important advice for initial setup

important advice for initial setup
OWNER’S MANUAL
Model AC510
Baby Video and Sound Monitor
Model AC417, AC517
Baby Video, Sound and Movement Monitor
IMPORTANT ADVICE FOR INITIAL SETUP
DON
’T
FORG
ET
Movement Alarm
Your monitor comes with the movement alarm activated.
When switching on your monitor it will alarm, with or without
the Sensor Pad plugged in, if no movement is detected.
Deactivate the movement function to use the monitor without
the Sensor Pad.
Cord Safety
Ensure the Nursery Unit is at least 1 metre away from your
baby’s cot. The Sensor Pad cord must always be kept out of
reach of baby and secured using the cord cover kit provided.
PLEASE FOLLOW THE INSTRUCTIONS CAREFULLY FOR CORRECT SETUP
Please DO NOT return this product to the store. For assistance please
contact our helpline on 0345 009 1789 or email helpline@babyhelpline.co.uk
Mon – Fri 10am – 4pm, excluding bank holidays.
TABLE OF CONTENTS
WARNINGS...................................................................................................................................................3
SETUP REQUIREMENTS....................................................................................................................................5
STEP 1 - Charging the Parent Unit (9 hours)..............................................................................................6
STEP 2 - Positioning the Movement Sensor...............................................................................................7
STEP 3 - Setting up the Camera.....................................................................................................................8
STEP 4 - Getting to know your monitor.................................................................................................... 12
STEP 5 - A
ctivating and deactivating additional functions................................................................ 16
STEP 6 - A
dding accessories........................................................................................................................ 26
Troubleshooting................................................................................................................................................ 28
Limited warranty............................................................................................................................................... 29
Technical specifications.................................................................................................................................. 29
OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING
& USING THE PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH OR DAMAGES TO THE PRODUCT.
THE SENSOR PAD FEATURE IS NOT FOR USE WITH ADULTS, CHILDREN OR INFANTS
OLDER THAN 24 MONTHS.
THE SENSOR PAD IS NOT INTENDED TO BE USED TO DETERMINE IF A CHILD IS OUT OF
THE CRIB.
WARNING
Adult assembly required.
Keep small parts away from children when assembling.
We, at Angelcare®, stand behind all of our products.
If you are not completely satisfied or have any questions,
United States and Canada: Please contact us at: angelcare@cdecinc.ca
Other countries: Please contact your local distributor.
FCC AND IC REGULATIONS
RF radiation exposure statement
The Camera complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
Caution: To maintain the compliance with the FCC’s and Industry Canada’s RF exposure guideline, install the
Camera at least 20 cm from ALL persons. The transmitter of this device must not be co-located or operating
in conjunction with any other antenna or transmitter.
Industry Canada
This product meets the applicable Industry Canada technical specifications.
CAN ICES-3 (B)/NMB-3 (B)
2
WARNINGS
1 . T H I S P R O D U C T C A N N OT R E P L A C E
RESPONSIBLE ADULT SUPERVISION. This product
is designed to aid in the monitoring of your child.
When using the monitor, you must still provide the
supervision necessary for the continued safety
of your child. Monitoring of premature babies,
or those considered to be at risk, should always
be carried out under the supervision of a health
professional. This monitor SHOULD NOT be used
as a medical device, nor as a device to prevent
Sudden Infant Death Syndrome (SIDS).
2. WARNING Strangulation Hazard — Children
have STRANGLED in cords. Keep adapter cords
o ut of th e re a ch of
children (more than 1
meter away). NEVER use
Sensor Pad(s) without
t h e p r o te c t i ve c o r d
covering.
Check
protective cord covering
before
each
use.
Immediately discontinue
use of Sensor Pad(s) if
protective covering is
damaged or broken.
3. Never use extension cords with adapters. ONLY
use the adapters provided.
4. When an adapter is plugged into an electrical
outlet, DO NOT touch the exposed end.
5. ALWAYS be sure that both the transmitter and
receiver are working properly and are within range
of each other. Test the monitor before first use,
periodically and when changing location of the
Camera.
6. ALWAYS be sure to immediately check on baby
whenever an alarm sounds.
7. DO NOT use monitor near water (such as bath
tub, sink, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT EXPOSE TO RAIN OR MOISTURE
8. Keep monitor AWAY from heat sources (such
as stoves, radiators, etc.).
9. ALWAYS place both the Camera and the Parent
Unit on a flat surface in an upright position and
allow for proper ventilation. DO NOT place on
sofas, cushions, beds, etc. which may block
ventilation.
10. This monitor uses public airwaves to transmit
signals. The Parent Unit may pick up signals or
interference from other nursery monitors in your
area. Your monitor may even be picked up by
other households. To protect your privacy, make
sure both units are turned OFF when not in use. If
you experience interference, change the channel
on both units.
11. This product is NOT a toy. DO NOT allow
children to play with it.
12 . This product contains small parts. Adult
assembly required. Exercise care when unpacking
and assembling the product and keep small parts
away from children.
E
N
13. When using the monitor, the room temperature
should be between 10°C and 40°C.
BATTERY WARNING
14. The Parent Unit battery is a replaceable Li-Ion
battery. Only use the Angelcare recommended
replacement battery. Danger of explosion if the
wrong battery is used or if replaced incorrectly.
Refer to your user manual for correct battery
installation. DO NOT short circuit supply terminals.
Only use the Angelcare provided power adapter
to charge the battery. Remove the battery from
your Parent Unit if product is to be stored for an
extended period of time. Dispose of batteries
according to your local ordinances. ALWAYS keep
all batteries away from children.
15. IMPORTANT SAFETY INSTRUCTIONS
15.1 Heed all warnings – All warnings on the
product and in the operating instructions should
be adhered to.
15.2 Follow all instructions – All operating and
use instructions should be followed.
15.3 Water and moisture - DO NOT use this
apparatus near water. For example, near a bath
tub, wash bowl, kitchen sink, laundry tub, in a wet
environment or near a swimming pool and the
like. Care should be taken so that objects DO NOT
fall onto units and that liquids are not spilled into
either unit or Sensor Pad through its openings.
15.4 Cleaning - Disconnect all units before
cleaning. DO NOT immerse in water any part of
the monitor. Clean only with dry cloth.
15.5 Ventilation - DO NOT block any ventilation
openings. Allow for proper ventilation when units
are in use. DO NOT cover the Camera or the Parent
Unit with any object such as a blanket. DO NOT
place it in a drawer or in any location which would
muffle the sound or interfere with the normal flow
of air.
15.6 Heat sources - DO NOT install near any heat
sources such as radiators, heat registers, stoves,
TVs or other apparatus (including amplifiers)
that produce heat. Heat can damage the case or
electrical parts.
15.7 Power cord protection - Protect the Sensor
Pad cord and Adapter’s power cord from being
walked on or pinched by furniture or other items –
Power supply cords should be routed so that they
are not likely to be walked on or pinched by items
upon or against them, paying particular attention
to cords and plugs, convenience receptacle, and
the point where they exit from the product.
The socket outlet shall be installed near the
equipment and shall be easily accessible. Make
sure to plug the adapter to the socket outlet
nearest to the equipment and that is easily
accessible. To disconnect from mains, unplug
the adapter.
3
15 . 8 Accessories - Only use attachments/
accessories specified by the manufacturer. DO
NOT place this product on an unstable cart,
stand, tripod, bracket or table. The product may
fall, causing serious injury to a child or adult and
serious damage to the product. Use ONLY with a
cart, stand, tripod, bracket or table recommended
by the manufacturer or sold with the product.
Any mounting of the product should follow the
manufacturer’s instructions.
15.9 Unplug this appliance during lightning storms
or when not used for long periods of time.
15.10 Servicing - DO NOT attempt to service
this product yourself as opening or removing
covers (except battery door) may expose you to
dangerous voltage or other hazards.
15.11 Replacement parts - When replacement
parts are required, be sure the replacement parts
specified by the manufacturer have the same
characteristic as the original part. Unauthorized
substitution may result in fire, electric shock or
other hazards.
15.12 Usage - This baby monitor is intended as
an aid. It is NOT a substitute for responsible and
proper adult supervision and should not be used
as such. Use this appliance ONLY for its intended
use as described in this manual.
15.13 Power Sources - Operate this product only
from the type of power source indicated on the
type plate of the adaptor. If you are unsure of the
type of power supply to your home, consult your
dealer or local power company.
15.14 Overloading - DO NOT overload wall
outlets, extension cords or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
15.15 Object and Liquid Entry - NEVER push
objects of any kind into this product through
casing slots as they may touch dangerous voltage
points or short out parts that could result in a risk
of fire or electric shock. NEVER spill liquid of any
kind on the product.
15.16 Antenna - The antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from all
persons and must not be collocated or operating in
conjunction with any other antenna or transmitter.
15.17 Power Lines - An outside antenna system
should NOT be located in the vicinity of overhead
power lines or other electric light or power circuit,
or where it can fall into such power lines or circuits
as contact with them may be fatal.
15.18 Vibration Source - When the monitor is
in use, DO NOT use a crib mobile or other crib
accessories that may produce vibrations. Other
sources of vibrations may include fans, washing
machines, loud music, etc. These sources of
vibration may interfere with the performance of
your Angelcare® monitor and the alarm will not
sound if it continues to detect any movement
other than your baby’s. Be sure all vibration
sources are eliminated before using the monitor.
You may experience false alarms for several reasons.
The most common reason is the Camera has not
been turned OFF after you have removed your baby
from the crib. Another reason is the Sensor Pad
has not been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm surface
4
with the printed side facing up. The sensitivity
level may also need to be adjusted. Refer to Step
5.1. Always be sure to immediately check on baby
whenever an alarm sounds.
15.19 Sensor Pad - Your Sensor Pad can be used
in any crib that is stationary. If the crib has a
spring or slat base, place a hard board between
the crib base and the Sensor Pad measuring
at least 33 x 33 cm and 6 mm thick. Only use
your Angelcare® monitor in a stationary sleeping
environment such as a crib where the Sensor
Pad can rest on a completely flat, firm surface.
The Sensor Pad is made of plastic and does not
permit the air to circulate. Therefore, mildew
build up could develop underneath the mattress
in the Sensor Pad area. We suggest rotating
the mattress regularly to prevent any mildew.
1 6 . I M P O R TA N T SA F E T Y I N S T R U C T I O N S
RELATED TO USE OF BATTERIES
16.1 Use ONLY the type and size of batteries
specified in the owner’s manual. There is a risk
of explosion if batteries are replaced with an
incorrect type.
16.2 Charge the battery for 9 hours prior to first
use. Be sure to have the monitor in the OFF
position during this period. ONLY use the adapters
included with your monitor.
16.3 DO NOT use these adapters with any other
equipments.
16.4 When unplugging the adapter from the
Camera, be sure it is switched to the OFF position.
If it isn’t, the unit will revert to battery mode if
batteries are installed.
16.5 DO NOT use rechargeable batteries in the
Camera. Use alkaline batteries ONLY.
16.6 DO NOT dispose batteries in fire. They may
explode. Check with local regulations for possible
special disposal instructions.
16.7 Exercise care in handling batteries in order
not to short out the batteries with conducting
materials such as rings, bracelets and keys.
Overcharging, short circuiting, reverse charging,
mutilation, or incineration of batteries must be
avoided to prevent one or more of the following
occurrences: release of toxic materials, release of
hydrogen and/or oxygen, gas and rise in surface
temperature.
16.8 DO NOT attempt to recharge batteries
provided with or identified for use with this
product that are not intended to be charged.
The batteries may leak corrosive electrolyte or
explode.
16.9 DO NOT attempt to rejuvenate the batteries
provided with or identified for use with this
product by heating them. Sudden release of
battery electrolyte may occur, causing burns or
irritation to eyes or skin.
16.10 If and when necessary, the batteries must
be replaced with identical new ones or equivalent
(volts and size). If a battery to be replaced is
connected with other batteries in series, replace
the other batteries at the same time as well. DO
NOT mix old and new batteries.
16.11 Reverse polarity installation of the batteries
in the end product must be avoided. Reverse
insertion of batteries can cause charging, and
that may result in leakage or explosion.
16.12 Remove batteries from both units if you store
the product over 30 days because the batteries
could leak and damage the product.
16.13 Discard ‘dead’ batteries as soon as possible
since ‘dead’ batteries are more likely to leak in a
product. If a battery has leaked or vented, it should
be replaced immediately using protective gloves.
16.14 DO NOT store this product, or the batteries
provided with or identified for use with this
product, in high-temperature areas.
WARNING
17.1 Warning: Changes or modifications to this
equipment not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
17. 2 NOTE: This equipment has been tested
and found to comply with part 15 of the FCC
Rules and the Industry Canada license-exempt
RSS standard(s). These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
17. 3 H owever, there is no guarantee that
inter ference will not occur in a par ticular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct
the interference by one or more of the following
measures:
E
N
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
17.4 This device complies with the part 15 of the
FCC Rules and the Industry Canada license exempt RSS standards(s). Operation is subject
to the following two conditions:
17.5 ( 1) This device may not cause harmful
interference, and
17.6 (2) This device must accept any interference
received, including interference that may cause
undesired operation.
Model AC510
SETUP REQUIREMENTS
Baby Video and Sound Monitor
Model AC417, AC517
INCLUDED:
Touch control Parent Unit
AC adapter
(for Parent Unit)
Baby Video, Sound and
Movement Monitor
Camera
Lithium ion battery pack
(for Parent Unit)
Tabletop stand
(for camera)
AC adapter
(for camera)
5
INCLUDED (CONTINUED):
* Always place printed side up *
CR3032 battery
(for Sensor Pad)
Adhesive strips
(for flat micro USB cable)
Wall mount
(for camera)
with hardware
(Screwdriver required
for wall mounting)
Flat micro USB cable
(for camera adapter)
Wireless movement Sensor Pad
(only for Model AC417, AC517)
STEP 1 - CHARGING THE PARENT UNIT (9 HOURS)
Battery compartment lock
1) Unlock the battery compartment on
the backside and remove the cover.
Insert the provided rechargeable
battery into the compartment.
Contacts of the battery and the
contacts in the compartment must be
aligned.
2) Connect the USB plug to the
Parent Unit.
3) Connect the power adapter
with an electrical outlet.
2
4) Charge the unit for 9
continuous hours prior to first
use.
3
6
PARENT UNIT:
Power
On/Off
E
N
Power indicator
Visual sound indicator
Microphone
Volume
control +/(on the side)
Micro USB
charging port
(on the side)
Folding stand (on backside)
Rechargeable battery
compartment (on reverse)
WARNING
STRANGULATION HAZARD.
Children have STRANGLED in cords:
•Keep adapter cords out of the reach of children (more
than 3 feet / 1 meter away).
•Because of the serious strangulation risk to infants
and toddlers, parents and caregivers should never
place the Camera within 3 feet / 1 meter of a crib.
•NEVER use extension cords with adapters. ONLY use
the adapters provided. This product is not a toy. Never
allow children to play with it.
7
STEP 2 - POSITIONING THE MOVEMENT SENSOR
Note: If you have model AC510 (no Sensor Pad) you can skip to Page 9.
2.1 - POWERING THE MOVEMENT SENSOR PAD
1) When using the Sensor Pad for the first time, you will need to insert the provided
CR3032 battery.
2) Remove the battery cover using a coin. Turn in the direction of the arrow.
3) Place the included battery (CR3032) in the compartment.
Note: The + symbol should be facing up.
4) Replace the battery cover (the two dots will line up). The Sensor Pad is now ON.
5) Verify the wireless Sensor Pad icon is on the status bar of your Parent Unit when
monitor is set up.
2.2 - INSTALL THE SENSOR PAD ON THE MATTRESS SUPPORT
2
1) Remove the mattress from the crib.
2) Place the Sensor Pad - printed side up
- in the center of the crib. It should be
centered on the hardboard if your crib
requires a hardboard support.
3) Replace the mattress.
Sensor Pad
8
IMPORTANT
If your crib does not have a solid, stable surface for the
Sensor Pad, you will need to place a hard support board
(not included) underneath the Sensor Pad to ensure correct
operation of the system.
This hardboard support should be at least ¼” (6 mm) thick
and should have minimum dimensions of 13” x 13” (33 cm x
33 cm). This support board must be larger than the Sensor
Pad surface area.
E
N
Hardboard
• Place the Sensor Pad directly underneath the mattress (and on top of support board, if
needed) in the center of the crib. Make sure there is nothing between the mattress and
Sensor Pad to interfere with operation.
• Never immerse the Sensor Pad in water or other liquids!
STEP 3 - POSITIONING THE CAMERA
3.1 - SELECT A LOCATION FOR THE CAMERA
WARNING
IMPORTANT
Place the crib near a supporting wall and far from air currents. Install the Camera on a flat,
stable surface facing the crib at a distance of at least 1 meter / 3 feet. Make sure to plug
the adapter to the socket outlet nearest to the equipment and that is easily accessible.
Place the
camera at least
3 ft (1m) from
the crib
9
3.1 - CAMERA
A
B
C
D
A)POWER ON/OFF
B)Pause Sensor Pad
E
C)Speaker
D)Microphone
F
E)Camera
F)Room temperature display
G)Micro USB charging port
G
Front Side
3
1) Place the Camera at a
minimum of 1 meter /
3 feet away from the crib.
2) Connect the USB plug to
the Camera.
2
3) Connect the USB plug to
the power adapter and then
into an electrical outlet.
4) Adjust the camera using
the magnetic mount to get
the best view of baby in the
crib.
10
SWITCHING ON YOUR MONITOR
E
N
1
1) Press and hold the Parent Unit
ON/OFF button for 2 seconds until
LCD screen is switched ON. Angelcare’s
logo will be shown for 1 second.
2
2) Slide the Camera ON/OFF switch to
the ON position
3) The Parent Unit will now display Video
mode screen.
If there is a lost connection between the
2 units after 15 seconds, the Out-of-Range
alarm will sound on the Parent Unit (refer to
troubleshooting):
When Parent Unit is turned
ON and Camera is OFF,
Parent Unit will display
Out-of-Range mode.
• The Out-of-Range icon will appear on the
screen.
• The Out-of-Range icon will appear on the info
bar.
INFO BAR IMPORTANT ICONS
Sensor Pad Status icons: Indicates the current status of the Sensor Pad
Normal Status
Sensor Pad Alert
Sensor Pad is Paused
Camera icons: Indicates which camera is currently viewed
Talk icon: Indicates when the Talk button is being pressed
Vox icon: Indicates when the camera is in VOX mode
Temperature icon: Indicates room temperature
Temperature Alerts Icons: Indicates Temperature Alarm is active
Too Warm
Too Cold
Connection Icon: Indicates the connection quality between the Parent Unit and the Camera
Out-of-Range
Poor connection
Medium connection
Good connection
Sound Level Icon: Indicates sound level
Mute (0/5)
2/5
3/5
4/5
5/5
Battery Level icon: Indicates battery life
Empty
1/4 Full
1/2 Full
3/4 Full
Full
Fully charged
11
STEP 4 - GETTING TO KNOW YOUR MONITOR
Time/Temperature
Camera connection
signal strength
Volume level
Active Camera
2:04
18°C
Battery status
of parent unit
Adjust screen
brightness
Pause sensor pad
Zoom
Main settings menu
Activate talk
back feature
Show reporting
Select Camera
Your Angelcare® monitor can be used with the preprogrammed factory settings or you
can customize the settings to your preference. Your monitor is equipped with a touch
screen. Just a tap anywhere on the screen will bring up the menu and feature selections.
IMPORTANT
When in menu or sub-menu modes, sound transmission between Parent and Cameras
will be temporarily deactivated. ONLY movement-detection alarm will remain active (if
function is activated).
4.1 - SENSOR PAD (MODEL AC417 & AC517)
Note: If you have model AC510 (no Sensor Pad) you can skip to Page 15.
IMPORTANT
• To ensure adequate monitoring of your baby’s movements, you can adjust the
sensitivity of the Sensor Pad in the main settings menu.
• Set a high sensitivity for a newborn and a lower sensitivity as baby grows and gains
weight. A thicker mattress will also need a higher sensitivity.
• Alarm will sound if there is no movement after 20 seconds.
IMPORTANT
The Sensor Pad is not designed for use with adults, children or infants older than 24
months. Once you are finished using the Sensor Pad, deactivate the movement function
then remove it from the baby’s crib and store it away.
12
TO ACTIVATE/DEACTIVATE THE SENSOR PAD:
18°C
E
N
1) Tap the screen anywhere to bring up the
menu.
2
2) Tap the Settings Icon
3) Tap the Sensor Pad Icon
18°C
4
3
5
.
.
4) Tap the Sensor Pad Toggle button to
activate the Sensor Pad (the toggle
button will turn blue).
5) Tap the Save Icon at the bottom of the
screen.
TO TEST THE SENSOR PAD:
IMPORTANT
• Test your monitor before first use.
• Test your monitor regularly to ensure it is functioning correctly.
• Test your monitor every time you move the Sensor Pad to a different place.
1) After activating the Sensor Pad, the alarm will
sound after 20 seconds.
2) Rub you hand over the mattress and confirm
the alarm stops.
MOVEMENT ALARM
IF THE ALARM DOES NOT SOUND
• Alarm activates when no movement
is detected by the Sensor Pad for
20 seconds.
• Both the Parent Unit and the
Camera speakers will emit
continuous beeps.
• Movement Alarm icon will show on
the LCD screen.
• Avoid contact with the crib while
Sensor Pad is in operation.
• Place the crib near a supporting wall to
reduce vibrations.
• Adjust the Sensor Pad sensitivity level.
• Do not use bedside crib, mobile, fans,
loud music or anything else that may
cause vibration.
13
PAUSING AND RESTARTING THE SENSOR PAD:
• If you remove baby from the crib
to feed/comfort, you can pause
the sensor pad:
1. Tap screen, press Sensor Pad
in top left of screen to
icon
see pause icon . To deactivate,
tap anywhere on screen
2. Press the pause button on
nursery unit to see the pause
icon. To deactivate press pause
button again or tap anywhere on
screen.
• Don’t forget to restart by utilizing
the same methods to re-engage
the Sensor Pad.
Pause Sensor Pad
18°C
IMPORTANT
If you do not pause the Sensor Pad, the alarm will sound if there is no movement after
20 seconds
TO ADJUST THE SENSOR PAD SENSITIVITY LEVEL:
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
3) Tap the Sensor Pad Icon
.
.
18°C
or
4) Tap
level.
3
4
5
14
to adjust the sensitivity
5) Tap the Save Icon at the bottom of the
screen to confirm your settings.
4.2 - BATTERY
E
N
HOW TO CHECK THE BATTERY:
Unplug the adapter from the Parent
Unit and check the battery level
indicator.
1/4 full
1/2 full
3/4 full
full
HOW TO CHARGE THE BATTERY IN THE PARENT UNIT:
Leave the Parent Unit connected to power
to fully charge the unit. Although the battery
at 1/4 capacity works normally, we recommend
that you fully recharge it.
PARENT UNIT BATTERY ALERT
• Alert activates when the battery needs to be
recharged.
• Parent Unit will emit a beep sound every
30 seconds.
• Battery Alert icon will show on LCD screen.
15
YOU ARE NOW READY TO USE YOUR MONITOR
The Angelcare® monitor can be used with the pre-programmed factory settings or you can also customize
your settings to your preference.
DEFAULT SETTINGS
Parent Unit Volume: Level 3 (of 4)
NU Speaker Volume: Level 3 (of 4)
Camera Microphone Sensitivity: Level 2 (of 4)
Movement Mode:
ON (AC417, AC517)
OFF (AC510)
Sensor Pad Sensitivity: Level 2 (of 4) (AC417, AC517)
Temperature Unit: Fahrenheit
Temperature Alert: OFF
Temperature Graphing: OFF (AC510)
ON (AC417, AC517)
Movement Graphing: ON (AC417, AC517)
VOX: OFF
Camera Color Changing Mode: White (No Color)
Screen Saver Timer: 30 seconds
LCD Brightness: Level 3 (of 5)
STEP 5 - ACTIVATING AND DEACTIVATING ADDITIONAL FUNCTIONS
IMPORTANT
When in the menu or sub-menu modes, sound transmission between Parent and
Cameras will be temporarily deactivated. ONLY the movement detection alarm will
remain active (if function is activated).
IMPORTANT
Movement function is pre-activated whether the battery is inserted in the Sensor Pad or
not. If there is no movement on the Sensor Pad after 20 seconds, a series of loud beeps
will emit from the Parent Unit and Nursery Unit - this is the movement alarm.
When not monitoring movement or changing/activating any settings on your monitor, to
prevent this alarm you can either:
1. Plug in/connect the Sensor Pad and gently tap the top of the Sensor Pad
2. Deactivate the movement function and refer to step 4.1
5.1 - SOUND TRANSMISSION (VOX)
VOICE ACTIVATION (VOX ON) OR CONTINUOUS SOUND (VOX OFF) MODE
16
SELECT VOX ON OR VOX OFF
1) Tap the screen anywhere to bring up
the menu.
18°C
2
2) Tap the Settings Icon
E
N
.
3) Tap the icon
to select the Camera
settings menu.
18°C
3
4
4) Tap the VOX Toggle button to activate
or deactivate the VOX function (toggle
will turn blue when VOX is active).
5) Tap the Save Icon at the bottom of the
screen to confirm your settings.
5
TO ADJUST THE SOUND SENSITIVITY:
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
.
3) Tap the icon
to select the Camera
settings menu.
18°C
3
or
to adjust the VOX
4) Tap
sensitivity level.
5) Tap the Save Icon at the bottom of the
screen (Icon will turn blue) to confirm
your settings.
4
5
5.2 - TALK BACK
Your parent monitor is equipped with Two Way Talk. This feature allows you to talk to baby
without being in the nursery.
TO ACTIVATE TWO WAY TALK:
1) Tap and hold the microphone icon
to activate talk back (Icon will expand
and turn blue).
2
18°C
1
2) Make sure you speak into the
microphone whilst pressing the
microphone icon..
3) Release the microphone icon
off the two way talk function.
to turn
17
TO ADJUST THE CAMERA VOLUME:
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
.
3) Tap the icon
to select the Camera
settings menu.
18°C
3
4
5
or
to adjust the two way talk
4) Tap
volume level.
5) Tap the Save Icon at the bottom of the
screen (Icon will turn blue) to confirm
your settings.
TO ADJUST & MUTE SOUND:
1) Press the Volume up / Volume down
button at the right side of the Parent
Unit to adjust the sound level.
1
18°C
2) To mute the sound press the Volume
down button until the mute symbol is
displayed.
3) To deactivate sound, press the Volume
up button until at desired level.
IF YOU HEAR NO SOUND:
•
•
•
•
Check that both units are powered ON.
Check that Parent Unit is not on MUTE.
Check the battery on the Parent Unit (recharge it if necessary).
Bring the Parent Unit closer to the Camera.
IMPORTANT
To avoid feedback (whistling), keep both units at least 3 meters / 10 feet apart.
18
5.3 - ROOM TEMPERATURE DISPLAY
E
N
TO CHANGE FROM CELSIUS TO FAHRENHEIT:
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
18°C
4
3
.
3) Tap the Temperature Icon to enter
the temperature settings menu.
to enter the
4) Tap the Edit Icon
temperature unit setting.
18°C
5
5) Tap the Temperature Unit Toggle
button to switch between °C and °F
(the toggle button and the chosen
setting will turn blue).
6) Tap the Save Icon at the bottom of the
screen (Icon will turn blue) to confirm
your settings.
6
TO ACTIVATE THE ROOM TEMPERATURE ALERT:
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
18°C
3) Tap the Temperature Icon to enter
the temperature settings menu.
3
4
18°C
66
.
5
86
to enter the
4) Tap the Edit Icon
temperature alarm setting menu.
5) Tap the Temperature Alarm Toggle
button to activate the alarm function
(the toggle button will turn blue when
active).
6) Tap the Save Icon at the bottom of the
screen (Icon will turn blue) to confirm
your settings.
6
19
TO SET THE ROOM TEMPERATURE RANGE:
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
18°C
3) Tap the Temperature Icon to enter
the temperature settings menu.
3
4
to enter the
4) Tap the Edit Icon
temperature alarm setting menu.
5) Set the lower and upper temperature
limit tapping the up/down arrows
18°C
5
66
.
.
6) Tap the Save Icon at the bottom of the
screen (Icon will turn blue) to confirm
your settings.
86
6
TO ACTIVATE THE CAMERA COLOR CHANGING MODE:
When activated, if the temperature goes outside of your set preferences, the temperature
digits on the Nursery Unit will either:
TOO HOT: display red
TOO COLD: display blue
Within your preferences: display white
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
18°C
3) Tap the Temperature Icon to enter
the temperature settings menu.
3
4
18°C
5
6
20
.
to enter the color
4) Tap the Edit Icon
changing mode menu.
5) Tap the Color Changing Mode Toggle
button to activate the color changing
mode (the toggle button will turn blue
when active).
6) Tap the Save Icon at the bottom of the
screen (Icon will turn blue) to confirm.
TEMPERATURE ALERT
• Alert activates when temperature reaches maximum or
minimum set temperature.
E
N
• Parent Unit will emit 4 consecutive beeps, every 5 seconds.
• Temperature Alert icon will show on LCD screen.
5.4 - HOW TO ACTIVATE TIME
For model AC510, please skip to Step 1.
For model AC417, AC517:
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
general settings menu.
to enter the
18°C
3
4
18°C
5
2
3) Tap the Edit Icon
settings menu.
to access the time
4) Tap the Time Mode Toggle button to
switch between 12 h and 24 h mode.
5) Set the hours and minutes using the
.
up/down arrows
08
6) Tap the Save Icon at the bottom of the
screen to confirm your settings.
6
IMPORTANT
Please remember to turn the Sensor Pad back on after setting the time / date if
deactivated.
21
5.5 - HOW TO CHANGE DATE
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
general settings menu.
to enter the
18°C
3
18°C
5
08
to access the date
4) Tap the Date Mode Toggle button to
switch between Month/Day/Year and
Day/Month/Year display.
4
2016
3) Tap the Edit Icon
settings menu.
5) Set the day, month and year using the
.
up/down arrows
22
6) Tap the Save Icon at the bottom of the
screen (Icon will turn blue) to confirm
your settings.
6
IMPORTANT
Please remember to turn the Sensor Pad back on after setting the time / date if
deactivated..
5.6 - SCREEN SAVER
Allows you to set the screen saver.
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
general settings menu.
to enter the
18°C
3
22
3) Tap the Edit Icon
to access the
screen saver settings menu.
1) Tap the Screen Saver Toggle button
to switch the screen saver on or off
(the toggle button will turn blue when
active).
4
18°C
00:00:30
00:01:00
00:02:00
00:03:00
5
E
N
2) Tap to select between 30 seconds to
3 minutes.
3) Tap the Save Icon at the bottom of the
screen to confirm your settings.
6
NOTE: SETTING:
MANUAL
The touchscreen will turn black when video is in Screen Saver mode. Tap the screen
To manually activate the Screen Saver mode, press the Parent Unit POWER ON/OFF button.
anywhere to return to Video mode.
5.7 - MOVEMENT AND TEMPERATURE MONITORING
(Model AC510 has Temperature Monitoring Only)
Activity analysis and room temperature tracking give you insight into your little one’s
activity level during sleep, helping you to better adapt routines and respond to their needs.
The movement monitoring records data every ten seconds. Three times every hour the
system compiles the collected data and a “movement activity report” can be viewed on the
Parent Unit.
TO TURN ON MOVEMENT AND TEMPERATURE MONITORING:
NOTE:
Model AC417, AC517 have movement settings ON. Model AC510, you will need to activate
movement monitoring if adding a Sensor Pad. .
IMPORTANT
Before turning on the movement and temperature monitoring, ensure you have set the
date and time in sections 5.4 and 5.5.
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
general settings menu.
to enter the
18°C
3) Tap the Edit Icon
to access the
monitoring settings.
3
23
4
1) Tap the Monitoring Toggle button to
switch the monitoring function
ON/OFF (the toggle button will turn
blue when ON).
18°C
2) Tap the Save Icon at the bottom of the
screen to confirm.
5
NAVIGATING MOVEMENT AND TEMPERATURE REPORTS:
18°C
1) Tap the screen anywhere to bring up
the menu.
2) Tap the Settings Icon
2
3
3
3) In the movement and temperature
reports, tap the arrows to navigate
hour by hour or day by day.
18°C
4
17
20
20
18
23
24
24
20
.
18
4) Tap the back arrow
Main Menu.
to go back to the
IMPORTANT MONITORING BUTTONS AND ICONS
Navigation Icons:
Go to previous page
Go to next page
Go to previous day
Go to next day
Sensor Pad Movement Levels: Indicates the amount of movement from your Sensor Pad
Low Movement
Medium Movement
High Movement
Graphing Icons:
Indicates an alert during the period
Indicates the system was turned off during the period
TO DELETE GRAPHING DATA:
Allows you to delete saved statistical graphs.
18°C
2
1) Tap the screen anywhere to bring up
the menu.
2) Tap the Settings Icon
general settings menu.
24
to enter the
18°C
3) Tap the Edit Icon
to access the
monitoring settings.
E
N
3
18°C
4
5) Tap the Bin Icon
to delete previously
saved graph data. If no data has been
saved yet, this option will not be
available.
18°C
6
4) Tap the Bin Icon
to access the
graph delete menu.
5
to cancel deleting
6) Tap the Arrow
of previously saved graph data. You will
return to the previous screen.
5.8 - DIGITAL PAN AND ZOOM
Allows you to zoom in to twice the normal view.
1) Tap the screen anywhere to bring up
the menu.
18°C
2
18°C
2) Tap the Magnifier Icon
the zoom.
to activate
3) Use the arrow keys to zoom in on what
you want to see more closely.
3
4) Tap anywhere on the screen, except on
the arrows, to return to the Main Menu.
The camera will stay zoomed in. When
zoomed in, the Magnifier Icon will be
blue.
18°C
5
5) Tap on the blue Magnifier Icon
to
return to normal viewing mode. Zoom
is deactivated.
25
5.9 - LCD SCREEN BRIGHTNESS
Allows you to adjust the LCD screen brightness on the Parent Unit.
18°C
2
1) Tap the screen anywhere to bring up
the menu.
2) Tap the Brightness Icon
.
18°C
4
3
3) Tap
/
to decrease / increase the
brightness level.
4) Tap again the Brightness Icon
return to the Main Menu.
to
STEP 6 - ADDING ACCESSORIES
6.1 - ADDING A WIRELESS SENSOR PAD
If you have purchased a wireless Sensor Pad, please refer to page 8, step 2, to add this
to your monitor.
To activate/deactivate the Sensor Pad, and adjust if required, please refer to page 13,
step 4.1.
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
3) Tap the Pairing Icon
device pairing menu.
18°C
4
3
26
4) Tap the Icon
.
to enter the
to add a Sensor Pad.
appears,
5) When the trash can icon
the Sensor Pad is now paired.
6.2 - ADDING AN ADDITIONAL CAMERA
If you have purchased an Accessory Camera, please follow the steps below to add it to the
system.
E
N
18°C
1) Tap the screen anywhere to bring up
the menu.
2
2) Tap the Settings Icon
3) Tap the Pairing Icon
device pairing menu.
.
to enter the
to select/highlight
4) Tap the Icon
CAMERA 2 (icon will be grayed out).
18°C
5) Plug in and turn your Camera on.
7
4
3
6) Press and hold the Pause / Pairing
on the top right of the
button
Camera.
7) When the trash can icon
the Camera is paired.
appears,
VIEWING MULTIPLE CAMERAS:
With more than one camera you can view each camera individually or use the split screen
mode to view all cameras connected simultaneously. Follow the steps below for multicamera viewing:
2:04
18°C
1) Tap the camera selection icon CAM.
The Camera Select Menu will popup and active cameras will have an
icon with a camera number (inactive
cameras will be grayed out).
1
3
2:04
2) Tap on the Camera Icon
of the
camera you would like to view (the icon
turns blue).
18°C
3) The CAM # icon will appear in the left
hand side of the info bar.
2
2:04
18°C
4) To view the split screen option, tap the
.
Camera Icon
4
27
TROUBLESHOOTING
TAKING CARE OF YOUR RECHARGEABLE BATTERY
• Ensure that you fully charge your battery for 9 hours before its first use.
• To maintain maximum battery life it is recommended that you fully discharge your battery periodically.
If your Parent Unit is not in use, please turn it OFF.
FALSE ALARMS WHEN SENSOR PAD IS IN USE
• Turn OFF the Camera.
• Make sure there is no bedding between the mattress and the Sensor Pad.
• If the crib has a spring or slat base, place a hardboard between the crib base and the Sensor Pad
measuring at least 13 in x 13 in x ¼ in thick.
• Make sure the Sensor Pad is positioned as described under the setup requirements. Sensitivity
may need to be adjusted.
ALARM WILL NOT SOUND
• Avoid contact with the crib when the monitor is ON.
• Place crib near a solid supporting wall to avoid Sensor Pad from detecting movement from outside the
crib.
• You may need to decrease the sensitivity.
NO SOUND IS BEING TRANSMITTED (REFER TO PAGE 18)
•
•
•
•
Check monitor is not on mute, refer to step 5.1.
Check the volume level on the Parent Unit and the Camera to ensure they are set to an appropriate level.
Try bringing the Parent Unit closer to the Camera.
Charge the Parent Unit.
WEAK RECEPTION
•
•
•
•
•
Intermittent sound - change to vox off, refer to step 5.1.
Bring units closer together.
Change the position of one or both units.
Place units on a flat surface away from baby’s reach.
Recharge the Parent Unit.
STATIC, DISTORTION, INTERFERENCES
(FROM OTHER MONITORS, WIRELESS PHONES, WALKIE-TALKIES, ETC.)
• Rotate Parent Unit or move it away from source of interference.
FEEDBACK (LOUD NOISES EMITTED FROM THE PARENT UNIT)
• Move units farther apart (at least 3 meters).
• Decrease volume on Parent Unit.
THE PARENT UNIT SCREEN IS BLANK
•
•
•
•
28
Turn the Parent Unit back ON by pushing and holding the POWER ON/OFF button for 2 seconds.
Recharge the Parent Unit.
Check the nursery unit is on.
Reconnect the parent and nursery unit.
LIMITED WARRANTY
Angelcare® warrants to the original owner of this
product that Angelcare® video, movement and sound
monitor is free from any material and workmanship
defects, for a period of one (1) year from the date
of the original purchase. If this monitoring system
fails to function properly when used as directed
under normal conditions within the one year period,
Angelcare® will either repair or replace the product,
at our discretion, free of charge. Please contact your
distributor.
The product must be accompanied by a proof
of purchase, either a bill of sale or other proof
that the monitoring system is within the warranty
period. Angelcare® will bear the cost of repairing or
replacing the product and shipping it back to you.
This warranty does not apply to a product which
has been damaged as a result of improper
maintenance, an accident, improper voltage
supply or any other form of misuse. The warranty
is also void if the owner repairs or modifies the
product in any way. Angelcare® is not liable for
any incidental or consequential damages with
regard to this product. The warranty also excludes
any liability other than what is stated above. No
other warranty is given.
This warranty does not cover products and
accessories which are not Angelcare-branded, or
any problems that result from usage that is not
in accordance with product instructions, failure
to follow the product instructions, or problems
caused by using accessories, parts or components
not supplied by Angelcare.
E
N
LEGAL RIGHTS VARY FROM COUNTRY TO
COUNTRY. SOME COUNTRIES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
WE ARE NOT IN ANY WAY RESPONSIBLE FOR
ANY OUTCOME RESULTING FROM THE USE OF
THIS PRODUCT.
IMPORTANT! This Angelcare® monitor is a personal
care product. Please do not return this product
to the store. If you have questions or need help,
please call your distributor before returning this
product.
TECHNICAL SPECIFICATIONS
Range:
Open field (Open area without obstructions):
up to 820 ft / 250 meters.
Number of Channels:
USA/Canada: 24 channels.
Europe: 24 channels.
Power Supply:
1 included Li-Ion battery (Parent Unit)
100 - 240 VAC / 5 VDC adapter for the Parent Unit
100 - 240 VAC / 5 VDC adapter for the camera
1 included CR3032 battery (wireless Sensor Pad)
(AC417, AC517)
Caution: To reduce the risk of electric shock, do
not expose this product to rain or moisture.
Danger of explosion if batteries are incorrectly
replaced. The battery included for the Parent Unit
is a user replaceable Li-ion rechargeable battery,
manufactured by Icon Energy System (Shenzhen)
Co Ltd. Only use the Angelcare recommended
replacement battery. To obtain information on
replacement batteries please contact Angelcare
customer service: www.angelcarebaby.com or
contact your local distributor. Instructions will be
included with the replacement battery. Dispose
of exhausted batteries properly according to your
local ordinances. Keep all batteries away from
children.
Batteries:
• DO NOT mix alkaline standard
(carbon-zinc), or rechargeable
(NI-CD, NIMH, etc.) batteries.
Transmission:
Data transmission between the Parent
Unit and the Camera is made on the 2.4 GHz
frequency.
Maximum RF Power Transmitted = 13.6dBm
(22.9mW)
Hereby, Angelcare Monitors Inc., declares that
this Baby Monitor is in compliance with Directive
2014/53/EU. Please click here to be directed
to the full text version of the EC Declaration of
Conformity .
PROTECT THE ENVIRONMENT
This electronic equipment contains reusable material and must not be
disposed with domestic waste. Please take it to a collecting point for
electric and electronic equipment (ask your local authorities for details).
29
This Angelcare Baby Monitor is a Personal Care Product. Please DO NOT return
this to the store, but contact us initially for advice and assistance:
Angelcare Helpline on 0345 009 1789
Website: www.angelcare.co.uk
Email: helpline@babyhelpline.co.uk
NOTE: Helpline is open Monday to Friday, 10am to 4pm, excluding bank holidays.
IM510-UK-100217
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising