New Product Switch Mode Power Supply S8VK-S (60/120-W Models) A Perfect Fit for Small Control Panels Coated PCBs for Better Resistance to Environment Connections for Easy Wiring • Operation possible at ambient temperatures from -40 to 70°C. • DC input supported (90 to 350 VDC). • Power Boost function at 120%. • Horizontal side-by-side mounting. • Vibration resistance to 5G, and 300-VAC abnormal input voltage supported for 1 second. • Complies with EN/IEC 61558-2-16. • Push-In Plus terminals reduce wiring time by 60% compared to screw terminals • UL 508 Listing/UL 1310 Class 2 output standards *1 • ANSl/ISA 12.12.01 • Certification for 3,000 m altitude (UL/EN/IEC 60950-1 and EN 50178). ! • Lloyd’s, DNV GL *2 • Conforms to F47-0706 • Five-year warranty *3 *1.UL 1310 Class2 output (For 60W Only) *2.Certification is pending for DNV GL. *3.Refer to Period and Terms of Warranty on page 16 for details. Refer to Safety Precautions for All Power Supplies and Safety Precautions on page 11. Ordering Information Model Number Legend Note: Not all combinations are possible. Refer to List of Models in Ordering Information, below. S8VK- S@@@@@ 1 2 1. Power Ratings 060: 60 W 120: 120 W Power ratings 60 W 120 W 2. Output voltage 24: 24 V Rated input voltage 100 to 240 VAC (allowable range: 85 to 264 VAC or 90 to 350 VDC) Rated output voltage Rated output current Maximum boost current Model number 24 V 2.5 A 3A S8VK-S06024 24 V 5A 6A S8VK-S12024 Mounting Brackets Name Model Front-mounting bracket (for 60 W models) S82Y-VS10F Side-mounting bracket (for 60 W models) S82Y-VS10S DIN Rail Mounting Track Name/specifications Mounting Track Models 50 cm (l) × 7.3 mm (t) PFP-50N 1 m (l) × 7.3 mm (t) PFP-100N 1 m (l) × 16 mm (t) PFP-100N2 End Plate PFP-M Spacer PFP-S 1 S8VK-S Specifications Ratings, Characteristics, and Functions Power rating 60 W 120 W Output voltage 24 V 24 V 115 VAC input *1 87% typ. 90% typ. Efficiency 230 VAC input *1 89% typ. 92% typ. Voltage range *2 Single-phase, 85 to 264 VAC, 90 to 350 VDC *12, 265 to 300 VAC (1 second) Frequency *2 50/60 Hz (47 to 450 Hz) 50/60 Hz (47 to 63 Hz) 115 VAC input *1 1.1 A typ. 1.2 A typ. Input current 230 VAC input *1 0.66 A typ. 0.63 A typ. Power factor Input 230 VAC input, 100% load --0.9 min. 115 VAC input 0.5 mA max. Leakage current *3 230 VAC input 1 mA max. 16 A typ. Inrush current *4 (for a 115 VAC input cold start at 25°C) 230 VAC input 32 A typ. Rated output current 2.5 A 5A Rated output electric power 60 W 120 W Maximum boost current 3A 6A Voltage adjustment range *5 21.6 to 28 V (with V.DJ) Ripple & Noise voltage 100 to 240 VAC input, 190 mVp-p max. 110 mVp-p max. *6 100% load *1 at 20 MHz of bandwidth at 20 MHz of bandwidth Input variation influence *7 0.5% max. Output Load variation influence *8 1.5% max. Temperature variation 115 to 230 VAC input 0.05%/°C max. influence 115 VAC input *1 800 ms typ. 400 ms typ. Start up time *4 230 VAC input *1 600 ms typ. 300 ms typ. 115 VAC input *1 20 ms typ. 45 ms typ. Hold time *6 230 VAC input *1 90 ms typ. 45 ms typ. Overload protection Yes, automatic reset Yes, 130% or higher of rated output voltage, power shut off (shut off the input voltage and turn on Overvoltage protection *9 the input again) Additional functions Series operation Yes (For up to two Power Supplies, external diodes are required.) Parallel operation Yes (For up to two Power Supplies), Refer to Parallel Operation on page 15 for details. Output indicator Yes (LED: Green) 3.0 kVAC for 1 min. (between all input terminals and output terminals), current cutoff 10 mA Withstand voltage 2.0 kVAC for 1 min. (between all input terminals and PE terminals), current cutoff 10 mA Insulation 1.0 kVAC for 1 min. (between all output terminals and PE terminals), current cutoff 20 mA Insulation resistance 100 MΩ min. (between all output terminals and all input terminals/PE terminals) at 500 VDC −40 to 70°C (Derating is required according to the temperature. Refer to Engineering Data) (with Ambient operating temperature *10 no condensation or icing) Storage temperature −40 to 85°C (with no condensation or icing) Environment Ambient operating humidity 95% RH max. (Storage humidity: 95% RH max.) Vibration resistance 10 to 55 Hz, maximum 5G, 0.42 mm half amplitude for 2 h each in X, Y, and Z directions Shock resistance 150 m/s2, 3 times each in ±X, ±Y, ±Z directions MTBF 135,000 hrs min. Reliability Life expectancy *11 10 years min. Weight 250 g max. 400 g max. Construction Cooling fan No Degree of protection IP20 by EN/IEC 60529 Harmonic current emissions Conforms to EN 61000-3-2 Conducted Emissions Conforms to EN 61204-3 Class B, EN 55011 Class B EMI Radiated Emissions Conforms to EN 61204-3 Class B, EN 55011 Class B EMS Conforms to EN 61204-3 high severity levels UL Listing: UL 508,ANSI/ISA 12.12.01 (For 60 W only Class2 Output: Per UL 1310) cUL: CSA C22.2 No107.1, CSA C22.2 No213 (For 60 W only Class2 Output: Per CSA C22.2 No.223) Approved Standards UL UR: UL 60950-1 (Recognition) OVCII (≤ 3000 m) Pol2 Standards cUR: CSA C22.2 No.60950-1 OVCII (≤ 3000 m) Pol2 EN: EN 50178 OVCIII (≤ 2000 m) OVCII (2000 m≤ and≤3000) Pol2, EN 60950-1 OVCII (≤ 3000 m) Pol2 PELV (EN/IEC 60204-1) *12 Conformed Standards EN/IEC 61558-2-16 *12 Lloyd’s register Marine Standards *12 DNV GL (Certification is pending for DNV GL.) SEMI Conforms to F47-0706 (200 to 240 VAC input) Item 2 S8VK-S *1. The value is when both rated output voltage and rated output current are satisfied. *2. Do not use an inverter output for the product. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of the product may result in ignition or burning. If the input is connected to a UPS, do not connect a UPS with a square-wave output. Doing so will cause the internal temperature of the product to increase, possibly causing smoking or burning. *3. The value for the leakage current is determined according to the Electrical Appliances and Material Safety Act. *4. Refer to Inrush Current, Startup Time, Output Hold Time on page 8 for details. *5. If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than 28 V min of the voltage adjustment range. When adjusting the output voltage, confirm the actual output voltage from the product and be sure that the load is not damaged. *6. A characteristic when the ambient operating temperature is 25°C. *7. This is the maximum variation in the output voltage when the input voltage is gradually changed within the allowable input voltage range at the rated output voltage and rated output current. *8. 100 to 240 VAC input, in the range of 0 A to the rated output current. *9. Refer to Overvoltage Protection on page 8 for the time when input voltage shuts off and input turns on again. *10.At -40 to -25°C, time will be required before the rated output voltage is output after the input voltage is input. Also, the ripple noise value may exceed the value shown in the above table. *11.Refer to Recommended Replacement Periods and Periodic Replacement for Preventive Maintenance on page 16 for details. *12.Refer to Standard Compliance, below. Standard Compliance • EN/IEC 61558-2-16 The S8VK-S was designed based on EN/IEC 61558-2-16. IEC 61558-2-17 has been replaced by IEC 61558-2-16. When certification was received for EN/IEC 60204-1 (Machinery Safety), it was necessary to go through a control transformer to the control circuits. However, a control transformer is not always necessary for products that have been certified for the safety standard for OVCIII or for products that use a transformer that conforms to EN/IEC 61558-2-16. • Safety Standards for a DC Input The following safety standards are applicable for when a DC input is used: UL 60950-1, cUR (CSA C22.2 No. 60950-1), EN 50178, EN 60950-1, Lloyd's, and DNV-GL. (Certification is pending for DNV GL.) Safety standard compliance is achievable by connecting a UL-certified fuse as specified below. Select an external fuse that satisfies the following conditions: S8VK-S06024: 350 VDC min., 6 A S8VK-S12024: 350 VDC min., 8 A • Conformance to Marine Standards Noise filter “FN2080-10-06” manufactured by SCHAFFNER Corporation or equivalent should be connected to the Input terminals of S8VK-S series. Add an End Plate (PFP-M) to both sides of the Power Supply to hold the Power Supply in place. • To comply with PELV output requirements for EN/IEC 60204-1, ground the negative side of the output (-V) to a protective earth (PE). 3 S8VK-S Connections Block Diagrams S8VK-S06024 (60 W) AC (L) INPUT AC (N) Rectifier Fuse 250 VAC 6.3 A HBC Inrush current protection Smoothing circuit circuit +V +V Noise filter −V −V Rectifier/ smoothing circuit Drive control circuit Overcurrent circuit DC OUTPUT −V Current detection circuit Voltage detection circuit Overcurrent detection circuit Overvoltage detection circuit Photocoupler S8VK-S12024 (120 W) AC (L) INPUT AC (N) Harmonic current Inrush current suppression circuit protection Smoothing circuit Rectifier (Power factor improvement) circuit Fuse 250 VAC 8.0 A HBC +V +V Noise filter −V Rectifier/smoothing circuit −V −V Drive control circuit Overcurrent circuit Current detection circuit Voltage detection circuit Overcurrent detection circuit Overvoltage detection circuit Photocoupler 4 DC OUTPUT S8VK-S Construction and Nomenclature Nomenclature 60-W Models 120-W Models S8VK-S06024 S8VK-S12024 6 7 1 8 2 3 No. Terminal name 1 L1 2 L2 3 N1 4 N2 5 PE 6 +V1 7 +V2 8 -V1 9 -V2 10 -V3 9 10 4 6 7 8 9 10 11 11 12 12 5 1 2 3 4 5 Name Function Input terminals Connect the input lines to these terminals. *1 Protective Earth terminal (PE) Connect the ground line to this terminal. *2 DC Output terminals Connect the load lines to these terminals. 11 --- Output indicator (DC ON: Green) The green indicator indicates when a DC voltage is being output. 12 --- Output voltage adjuster (V.ADJ) Use to adjust the voltage. *1. The fuse is located on the (L) side. It is not user-replaceable. For a DC input, connect the positive voltage to the L terminal. *2. This is the protective earth terminal specified in the safety standards. Always ground this terminal. 5 S8VK-S Engineering Data Derating Curve 120 W (S8VK-S12024) 120 100 A 75% 80 Load ratio (%) Load ratio (%) 60 W (S8VK-S06024) 120 100 A 80 65% B 50% 60 40 20 20 −25 0 −40 −10 0 10 20 30 40 50 60 70 80 Operating temperature (°C) −25 50% −10 0 10 20 30 40 50 60 70 80 Operating temperature (°C) A. Standard mounting, mounted with Front-mounting Bracket, or mounted with Side-mounting Bracket B. Face-up mounting A. Standard mounting B. Face-up mounting 60 W (S8VK-S06024) Front, Side-by-side mounting 120 W (S8VK-S12024) Front, Side-by-side mounting 120 100 C 80 Load ratio (%) Note: 1. At less than 90 VAC, derate the load at 2.5%/V. 2.For a DC input, reduce the load given in the above derating curve by multiplying by the following coefficients. S8VK-S12024: 0.9 3.In the shaded area, time is required to reach the rated output voltage after the input voltage is applied. Also, the ripple noise value in this area may exceed the range given on page 2. Load ratio (%) Note: 1. At less than 90 VAC, derate the load at 2.5%/V. 2.For a DC input, reduce the load given in the above derating curve by multiplying by the following coefficients. S8VK-S06024: 0.9 3.In the shaded area, time is required to reach the rated output voltage after the input voltage is applied. Also, the ripple noise value in this area may exceed the range given on page 2. 120 100 60 40 40 20 20 −10 0 10 20 30 40 50 60 70 80 Operating temperature (°C) Note: 1. Apply the rated voltage 2.In the shaded area, time is required to reach the rated output voltage after the input voltage is applied. Also, the ripple noise value in this area may exceed the range given on page 2. C. Front, Side-by-side Mounting C 80 60 0 −40 −25 6 60 40 0 −40 B 0 −40 −25 −10 0 10 20 30 40 50 60 70 80 Operating temperature (°C) Note: 1. Apply the rated voltage 2.In the shaded area, time is required to reach the rated output voltage after the input voltage is applied. Also, the ripple noise value in this area may exceed the range given on page 2. C. Front, Side-by-side Mounting S8VK-S This Power Supply can be used at an altitude of 3,000 m. Between 2,000 and 3,000 m, derate the load according to the following derating curve. 120 W (S8VK-S12024) 120 100% 100 90% 87 80 75 77% 65% Load ratio (%) Load ratio (%) 60 W (S8VK-S06024) 120 100% 100 80% 82 80 65% 65 60 60 50% 55°C max 40 40 60°C 65°C 20 0 55°C max 500 65°C 20 70°C 0 60°C 0 1,000 1,500 2,000 2,500 3,000 3,500 Altitude (m) 70°C 0 500 1,000 1,500 2,000 2,500 3,000 3,500 Altitude (m) Standard mounting, mounted with Front-mounting Bracket, or mounted with Side-mounting Bracket Standard mounting 60 W (S8VK-S06024) Front, Side-by-side mounting 120 W (S8VK-S12024) Front, Side-by-side mounting 120 100% 100 85% 75% 80 60 Load ratio (%) Note: 1. At less than 90 VAC, derate the load at 2.5%/V. 2.For a DC input, reduce the load given in the above derating curve by multiplying by the following coefficients. S8VK-S12024: 0.9 Load ratio (%) Note: 1. At less than 90 VAC, derate the load at 2.5%/V. 2.For a DC input, reduce the load given in the above derating curve by multiplying by the following coefficients. S8VK-S06024: 0.9 120 100% 100 85% 75% 80 60 35°C max 40 55 °C 20 0 35°C max 40 40°C 0 500 Front, Side-by-side mounting 55 °C 20 1,000 1,500 2,000 2,500 3,000 3,500 Note: 1. Apply the rated voltage 40°C Altitude (m) 0 0 500 1,000 1,500 2,000 2,500 3,000 3,500 Altitude (m) Note: 1. Apply the rated voltage Front, Side-by-side mounting 7 S8VK-S Two phase application for Single phase models Mounting (B) Face-up mounting (A) Standard (Vertical) mounting (C) Front, Side-by-side mounting For All Single phase Models, S8VK-S OMRON single phase power supply can be used on two-phases of a 3–phase-system when some of conditions are satisfied like below. 1.The supplying voltage is below the maximum rated input. OMRON Power supply allows the input voltage equivalent or less than 240 VAC+10%. Please confirm the input voltage between two lines if the input voltage satisfies this condition before connecting. 2.The external protector is needed on N input line to secure a safety. N line has no protection of a fuse internally. An appropriate fuse or circuit breaker should be connected on N input line like the following. Overload Protection L1 L2 L3 PE Power Supply Internal Fuse An external fuse or a circuit breaker L Output voltage (V) The load and the power supply are automatically protected from overcurrent damage by this function. Overload protection is activated if the output current rises above 121% of the rated current. When the output current returns within the rated range, overload protection is automatically cleared. max. 240 VAC+10% The values shown in this diagram are for reference only. Intermittent operation 0 50 Reference Value 100 Output current (%) Note: 1. Internal parts may occasionally deteriorate or be damaged if a short-circuited or overcurrent state continues during operation. 2.Internal parts may possibly deteriorate or be damaged if the Power Supply is used for applications with frequent inrush current or overloading at the load end. Do not use the Power Supply for such applications. Reliability (MTBF) Consider the possibility of an overvoltage and design the system so that the load will not be subjected to an excessive voltage even if the feedback circuit in the product fails. If an excessive voltage that is approximately 130% of the rated voltage or more is output, the output voltage is shut OFF. Reset the input power by turning it OFF for at least three minutes and then turning it back ON again. Note: Do not turn ON the power again until the cause of the overvoltage has been removed. Inrush Current, Startup Time, Output Hold Time Input ON Input OFF Input Voltage Inrush current on input application Input Current 96.5% 90% Output voltage Startup time Hold time Note: Twice the normal inrush current will flow during parallel operation or for backup operation. Also, if crossover wiring is used for N number of Power Supplies, an inrush current of N times the inrush current for a standalone Power Supply will flow. Therefore, check the fusing characteristics of fuses and operating characteristics of breakers making sure that the external fuses will not burn out and the circuit breakers will not be activated by the inrush current. Value Single phase model 60 W: 640,000 120 W: 480,000 Definition MTBF stands for Mean Time Between Failures, which is calculated according to the probability of accidental device failures, and indicates reliability of devices. Therefore, it does not necessarily represent a life of the product. Life expectancy 10 yrs. Min. Definition The life expectancy indicates average operating hours under the ambient temperature of 40°C and a load rate of 50%. Normally this is determined by the life expectancy of the built-in aluminum electrolytic capacitor. Overvoltage Protection 8 N S8VK-S Dimensions (Unit: mm) S8VK-S06024 (60 W) 90 ±1 (1.2) 5.4 78.55 86 90 ±1 Rail Stopper 5.4 32 ±1 3.5 4.7 (Sliding: 10 max.) S8VK-S12024 (120 W) 90 5.4 (1.2) 90 ±1 78.55 Rail Stopper ±1 86 3.5 5.4 55 ±1 4.7 (Sliding: 10 max.) 9 S8VK-S DIN Rail (Order Separately) (Unit: mm) Mounting Rail (Material: Aluminum) PFP-100N PFP-50N 7.3±0.15 4.5 35±0.3 15 25 10 25 25 10 1,000 (500) * 25 27±0.15 15(5) * 1 * Values in parentheses are for the PFP-50N. Mounting Rail (Material: Aluminum) PFP-100N2 16 4.5 35±0.3 27 15 25 10 25 25 10 1,000 25 15 24 29.2 1 1.5 End Plate PFP-M 10 6.2 M4×8 panhead screw 1 50 1.8 1.8 35.5 35.5 11.5 1.3 10 M4 spring washer 4.8 Note: If there is a possibility that the Unit will be subject to vibration or shock, use a steel DIN Rail. Otherwise, metallic filings may result from aluminum abrasion. Mounting Brackets Name Model S82Y-VS10F Front-mounting bracket (for 60 W models) Side-mounting bracket (for 60 W models) S82Y-VS10S Note: Be sure to use the accessory screws. Mounting screw tightening torque (recommended): 4.43 to 5.31 lb-in (0.5 to 0.6 N·m) Type Model Dimensions Appearance 41 4.5 dia.±0.1 Two locations Mounting screw tightening torque: 0.5 to 0.6 N·m 35 25 Front-mounting S82Y-VS10F bracket (For 60 W models) 35±0.1 7.3 10 40 50 t = 1.0 Left-side mounting 4.5 dia.±0.1 55±0.1 35 64 t = 2.0 10 60±0.1 80 Side-mounting bracket S82Y-VS10S (For 60 W models) 13 Three locations Mounting screw tightening torque: 0.5 to 0.6 N·m Right-side mounting S8VK-S Safety Precautions Warning Indications WARNING Indicates a potentially hazardous situation which, if not avoided, will result in minor or moderate injury, or may result in serious injury or death. Additionally, there may be significant property damage. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage. Precautions for Safe Use Supplementary comments on what to do or avoid doing, to use the product safely. Precautions for Correct Use Supplementary comments on what to do or avoid doing, to prevent failure to operate, malfunction or undesirable effect on product performance. Meaning of Product Safety Symbols Used to warn of the risk of electric shock under specific conditions. Used to warn of the risk of minor injury caused by high temperatures. Use to indicate prohibition when there is a risk of minor injury from electrical shock or other source if the product is disassembled. Used for general mandatory action precautions for which there is no specified symbol. !WARNING Insert the solid wire or ferrule straight into the terminal block until the end touches the terminal block. !CAUTION Minor electric shock, fire, or Product failure may occasionally occur. Do not disassemble, modify, or repair the Product or touch the interior of the Product. Minor burns may occasionally occur. Do not touch the Product while power is being supplied or immediately after power is turned OFF. Minor injury due to electric shock may occasionally occur. Do not touch the terminals while power is being supplied. Always close the terminal cover after wiring. Minor electric shock, fire, or Product failure may occasionally occur. Do not allow any pieces of metal or conductors or any clippings or cuttings resulting from installation work to enter the Product. 11 S8VK-S Precautions for Safe Use Installation Environment • Do not use the Power Supply in locations subject to shocks or vibrations. In particular, install the Power Supply as far away as possible from contactors or other devices that are a vibration source. For usage onboard a ship, always attach an End Plate (PFP-M) to both sides of the Power Supply to hold the Power Supply in place. • Install the Power Supply well away from any sources of strong, high-frequency noise and surge. To dismount the Block, pull down portion (C) with a flat-blade screwdriver and pull out the Block. 25 mm min. (C) Rail stopper Operating Life • The life of a Power Supply is determined by the life of the electrolytic capacitors used inside. Here, Arrhenius Law applies, i.e., the life will be cut in half for each rise of 10°C or the life will be doubled for each drop of 10°C. The life of the Power Supply can thus be increased by reducing its internal temperature. Ambient Operating and Storage Environments • Store the Power Supply at a temperature of −40 to 85°C and a humidity of 95% or less. • Do not use the Power Supply in areas outside the derating curve otherwise, internal parts may occasionally deteriorate or be damaged. • Use the Power Supply at a humidity of 95% max. • Do not use the Power Supply in locations subject to direct sunlight. • Do not use the Power Supply in locations where liquids, foreign matter, or corrosive gases may enter the interior of Power Supply. Mounting • Take adequate measures to ensure proper heat dissipation to increase the long-term reliability of the Power Supply. Be sure to allow convection in the atmosphere around devices when mounting. Do not use in locations where the ambient temperature exceeds the range of the derating curve. • When cutting out holes for mounting, make sure that cuttings do not enter the interior of the Power Supplies. *1 *1 *1 *2 Wiring • Connect the ground completely. A protective earthing terminal stipulated in safety standards is used. Electric shock or malfunction may occur if the ground is not connected completely. • Minor fire may possibly occur. Ensure that input and output terminals are wired correctly. • When you insert wires or insert a screwdriver into a release hole, do not press down on the terminal block with a force of 40 N or greater. • Do not wire anything to the release holes. • Do not tilt or twist a flat-blade screwdriver while it is inserted into a release hole on the terminal block. The terminal block may be damaged. • Insert a flat-blade screwdriver into the release holes at an angle. The terminal block may be damaged if you insert the screwdriver straight in. • Do not allow the flat-blade screwdriver to fall out while it is inserted into a release hole. • Do not bend a wire past its natural bending radius or pull on it with excessive force. Doing so may cause the wire disconnection. • Do not insert more than one wire into each terminal insertion hole. • Do not pre-solder the ends of the wires. Doing so will inhibit proper connection. • Be sure to remove the sheet covering the Product for machining before power-ON so that it does not interfere with heat dissipation. • Use the following material for the wires to be connected to the S8VK-S to prevent smoking or ignition caused by abnormal loads. Terminal name Model Recommended wire gauge Solid/stranded wire AWG Input terminal *3 *1 *3 *1 *1 *2 *1. Convection of air *2. Vertical separation: 25 mm or more *3. Horizontal separation: 15mm or more • S8VK-S Power Supplies can be mounted side-to-side. Use the Product within the derating curve for the front, side-by-side mounting. DIN Rail Mounting To mount the Block on a DIN Rail, hook portion (A) of the Block onto the rail and press the Block in direction (B). S8VK-S06024, S12024 AWG22 to 14 0.34 to 2.5 mm2 DC output terminal S8VK-S06024 AWG20 to 14 0.5 to 2.5 mm2 S8VK-S12024 AWG18 to 14 0.75 to 2.5 mm2 PE (protective earth) terminal S8VK-S06024, S12024 2.0 to 2.5 mm2 AWG14 • Input crossover wiring can be used for the input side of this Power Supply. • Do not use crossover wiring for more than five Power Supplies, and do not allow the steady-state current to the input terminals to exceed 5 A. The above table gives the recommended wires for one Power Supply. • If you use crossover wiring for N number of Power Supplies, a current that is N times the current for a standalone Power Supply may flow to the input terminals. Take this into consideration when you select wiring materials. Stripping length (A) Stripping length Recommended Wire (B) Ferrules used 0.34 to 1.5mm2/Equivalent to AWG22 to 16 10 mm 8 mm 2 to 2.5mm2/Equivalent to AWG14 10 mm 12 mm Note: Please use Ferrules with UL certification (R/C). 12 Ferrules not used S8VK-S ● Connecting wires to the Push-In Plus Terminal Block Part Names of the Terminal Block Terminal (Insertion) hole Release hole ● Removing wires from the Push-In Plus Terminal Block Use the following procedure to remove wires from the terminal block. The same method is used to remove stranded wires, solid wires, and ferrules. 1.Hold a flat-blade screwdriver at an angle and insert it into the release hole. 2.With the flat-blade screwdriver still inserted into the release hole, remove the wire from the terminal insertion hole. 3.Remove the flat-blade screwdriver from the release hole. Connecting Wires with Ferrules and Solid Wires Insert the solid wire or ferrule straight into the terminal block until the end touches the terminal block. 2 10 to 15° Terminal (Insertion) hole 3 1 Flat-blade screwdriver ● Recommended Ferrules and Crimping Tools Applicable wire Release hole (mm2) Ferrules and solid wires If a wire is difficult to connect because it is too thin, use a flat-blade screwdriver in the same way as when connecting stranded wire. Connecting Stranded Wires Use the following procedure to connect the wires to the terminal block. 1.Hold a flat-blade screwdriver at an angle and insert it into the release hole. The angle should be between 10° and 15°. If the flat-blade screwdriver is inserted correctly, you will feel the spring in the release hole. 2.With the flat-blade screwdriver still inserted into the release hole, insert the wire into the terminal hole until it strikes the terminal block. 3.Remove the flat-blade screwdriver from the release hole. 2 10 to 15° Flat-blade screwdriver 1 (AWG) Recommended ferrules Manufactured Manufactured Manufactured by Phoenix by by Wago Contact Weidmuller 0.34 22 8 AI0.34-8 H0.34/12 FE-0.34-8N-TQ 0.5 20 8 AI0.5-8 H0.5/14 FE-0.5-8N-WH 0.75 18 8 AI0.75-8 H0.75/14 FE-0.75-8N-GY 1 18 8 AI1-8 H1.0/14 FE-1.0-8N-RD 1.5 16 8 AI1.5-8 2.5 14 10 AI2.5-10 CRIMPFOX6 CRIMPFOX6-F CRIMPFOX10S Recommended crimp tool H1.5/14 FE-1.5-8N-BK H2.5/16DS FE-2.5-10N-BU PZ6 roto Variocrimp4 Note: 1. Make sure that the outer diameter of the wire is smaller than the inner diameter of the insulating sleeve of the recommended ferrule. 2. Make sure that the ferrule processing dimensions conform to the following figure. 8 to 10 mm 3 Checking Connections • After the insertion, pull gently on the wire to make sure that it will not come off and the wire is securely fastened to the terminal block. • To prevent short circuits, insert the stripped part of a stranded or solid wire or the conductor part of a ferrule until it is hidden inside the terminal insertion hole. (See the following diagram.) Ferrule Conduct or length (mm) 2.6 mm max. 2.8 mm max. Recommended Flat-blade Screwdriver Use a flat-blade screwdriver to connect and remove wires. Use the following flat-blade screwdriver. The following table shows manufacturers and models as of 2015/Dec. Side Front 2.5 mm dia. 0.4 mm 2.5 mm Model Manufacturer XW4Z-00B Omron ESD0.40✕2.5 Wera SZF 0.4✕2.5 Phoenix Contact 0.4✕2.5✕75 302 Wiha AEF.2.5✕75 Facom 210-719 Wago SDI 0.4✕2.5✕75 Weidmuller 13 S8VK-S The boost current is a temporary current that exceeds the rated current. However, it should meet the following four boost current conditions. 1.Time that the boost current flows: t1 ≤ 10 s 2.The boost current: Ip ≤ Maximum boost current 3.The average output current: Iave ≤ Rated output current 4.The time ratio of the boost current flow: Duty ≤ 30% Series Operation Two Power Supplies can be connected in series. INPUT −V INPUT −V t1 × 100 [%] ≤ 30% t1 + t2 [A] Ip: Boost current output current +V Rated current lave: Average current Note: 1.The diode is connected as shown in the figure. If the load is short-circuited, a reverse voltage will be generated inside the product. If this occurs the product may possibly deteriorate or be damaged. Always connect a diode as shown in the figure. Select a diode having the following ratings. Type Schottky Barrier diode Dielectric strength (VRRM) Twice the rated output voltage or above t2 • Do not allow a boost current to flow for more than 10 s. Do not allow the duty to exceed 30%. These conditions may damage the Power Supply. • Do not allow the average current for one cycle of the boost current to exceed the rated current. The Power Supply may be damaged. • Derate the load at the boost current according to the ambient operating temperature and mounting direction. Overcurrent Protection • Internal parts may possibly deteriorate or be damaged if a short-circuited or overcurrent state continues during operation. • Internal parts may possibly deteriorate or be damaged if the Power Supply is used for applications with frequent inrush current or overloading at the load end. Do not use the Power Supply for such applications. Making Positive/Negative Outputs • The outputs are floating outputs (i.e., the primary circuits and secondary circuits are separated). You can therefore make positive and negative outputs by using two Power Supplies. You can make positive and negative outputs with any of the models. If positive and negative outputs are used, connect Power Supplies of the same model as in the following figure. (Combinations with different output capacities or output voltages can be made. However, use the lower of the two maximum rated output currents as the current to the loads.) INPUT +V +V Load t1 Forward current (IF) Twice the rated output current or above 2.Although Products having different specifications can be connected in series, the current flowing through the load must not exceed the smaller rated output current. −V Charging a Battery If you connect a battery as the load, install overcurrent control and overvoltage protection circuits. Output Voltage Adjuster (V.ADJ) • The output voltage adjuster (V.ADJ) may possibly be damaged if it is turned with unnecessary force. Do not turn the adjuster with excessive force. • After completing output voltage adjustment, be sure that the output power or output current does not exceed the rated output electric power or rated output current. INPUT Load 0V +V −V −V • Depending on the model, internal circuits may be damaged due to startup failure when the power is turned ON if loads such as a servomotor or operational amplifier may operate in series. Therefore, connect bypass diodes (D1, D2) as shown in the following figure. INPUT +V D1 INPUT +V −V D2 Load Load −V Load Duty= +V Load Power Boost Function • Use the following information as a guide to the diode type, dielectric strength, and current. Type Schottky Barrier diode Dielectric strength (VRRM) Twice the rated output voltage or above Forward current (IF) 14 Twice the rated output current or above S8VK-S IN 1 +V Load INPUT +V −V −V S8VK-S INPUT +V −V Load S8VK-S +V S8VK-S +V INPUT −V • Use the following information as a guide to the diode type, dielectric strength, and current. Type Schottky Barrier diode Dielectric strength (VRRM) Twice the rated output voltage or above Forward current (IF) Backup operation is possible if you use two Power Supplies of the same model. Even if one Power Supply fails, operation can be continued with the other Power Supply. Make sure that the maximum load does not exceed the capacity of one Power Supply. Use the S8VK-R or connect external diodes. For backup operation with 60-W or 120-W Power Supplies, use the S8VK-R10. S8VK-S INPUT S8VK-R +V IN 1 +V −V −V S8VK-S INPUT +V IN 2 −V S8VK-S INPUT +V −V S8VK-S +V INPUT −V • Use the following information as a guide to the diode type, dielectric strength, and current. Type Schottky Barrier diode Dielectric strength (VRRM) Twice the rated output voltage or above Forward current (IF) Twice the rated output current or above In Case There Is No Output Voltage IN 2 −V INPUT Backup Operation Load Parallel operation is used when the output current from one Power Supply is insufficient for the load. Power Supplies are connected in parallel to increase the output current. Two Power Supplies can be connected in parallel. 1. You must meet the following conditions to use parallel operation. • Standard mounting. • The range of ambient temperature is -25 to 40°C. Left and right interval 15 mm or more, Up and down interval 25 mm min. • Rated input voltage range and output voltage of 25 V max. 2. <S8VK-S06024 Only> The total output current must be 4 A max. 3. Adjust the output voltage difference of each Power Supply to 50 mV or less, using the output voltage adjuster (V. ADJ). 4. There is no current balancing function for S8VK-S. A high output voltage unit may work at overcurrent state and in this situation, a life of a Power Supply will be extremely short. After adjusting the output voltage, confirm the output current of the Power Supplies balances. 5. Using the parallel operation will not satisfy UL1310 Class2 output. 6. For Parallel Operation, to balance the current of the each unit, the length and thickness of each wire connected to the load and each unit must be same as much as possible. 7. If you use the S8VK-S in parallel operation the output voltage may drop by several volts if the load changes rapidly (e.g., if the load starts or is disconnected). Use the S8VK-R or connect external diodes as shown in the figure. For parallel operation with 60-W or 120-W Power Supplies, use the S8VK-R10. 8. Do not use parallel operation when there is the possibility that the input voltage will vary outside of the rated S8VK-R input range. S8VK-S Load Parallel Operation Twice the rated output current or above The possible cause for no output voltage may be that the overcurrent or overvoltage protection has operated. The internal protection may operate if a large amount of surge voltage such as a lightening surge occurs while turning ON the power supply. In case there is no output voltage, please check the following points before contacting us: • Checking overload protected status: Check whether the load is in overload status or is short-circuited. Remove wires to load when checking. • Checking overvoltage or internal protection: Turn the power supply OFF once, and leave it OFF for at least 3 minutes. Then turn it ON again to see if this clears the condition. Audible Noise at Power ON <S8VK-S12024 only> A harmonic current suppression circuit is built into the Power Supply. This circuit can create noise when the input is turned ON, but it will last only until the internal circuits stabilize and does not indicate any problem in the Product. 15 S8VK-S Period and Terms of Warranty Warranty Period The Power Supply warranty is valid for a period of five years from the date of shipment from the factory. Terms of Warranty The warranty is valid only for the following operating conditions. 1. Average ambient operating temperature of the Power Supply: 40°C max. (See note.) 2. Average load rate of 80% max. (See note.) 3. Mounting method: Standard mounting 4. Rated input voltage Note: The maximum ratings must be within the derating curve. If the Power Supply fails for reasons attributable to OMRON within the above warranty period, OMRON will repair or replace the faulty part of the Power Supply at the place of purchase or the place where the Power Supply delivered without charge. This warranty does not cover the following types of failures. (1) Failures that result from handling or operation of the Power Supply under conditions or in environments that are not given in this document and not given in any other specifications exchanged between OMRON and the customer (2) Failures that originate in causes other than the delivered product itself (3) Failures caused by disassembly, modification, or repair of the Power Supply by anyone other than OMRON (4) Failures caused by applications or uses for which the Power Supply was not originally intended (5) Failures caused by factors that could not be anticipated with the scientific or technical knowledge available when the Power Supply was shipped (6) Failures caused by other causes for which OMRON is not responsible, such as natural disasters and other acts of God This warranty is limited to the individual Power Supply that was delivered and does not cover any secondary, subsequent, or related damages. Recommended Replacement Periods and Periodic Replacement for Preventive Maintenance The recommended replacement period for preventive maintenance is greatly influenced by the application environment of the Power Supply. As a guideline, the recommended replacement period is 7 to 10 years.* To prevent failures or accidents that can be caused by using a Power Supply beyond its service life, we recommend that you replace the Power Supply as early as possible within the recommended replacement period. However, bear in mind that the recommended replacement period is for reference only and does not guarantee the life of the Power Supply. Many electronic components are used in the Power Supply and the Power Supply depends on the correct operation of these components to achieve the original Power Supply functions and performance. However, the influence of the ambient temperature on aluminum electrolytic capacitors is large, and the service life is reduced by half for each 10°C rise in temperature (Arrhenius law). When the capacity reduction life of the electrolytic capacitor is reached, the Power Supply failures or accidents may occur. We therefore recommend that you replace the Power Supply periodically to minimize product failures or accidents in advance. * The recommended replacement period applies under the following conditions: rated input voltage, load rate of 50% max., ambient temperature of 40°C max., and the standard mounting method. This product model is designed with a service life of 10 years minimum under the above conditions. 16 Terms and Conditions of Sale 1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed part of all quotes, agreements, purchase orders, acknowledgments, price lists, catalogs, manuals, brochures and other documents, whether electronic or in writing, relating to the sale of products or services (collectively, the "Products") by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron objects to any terms or conditions proposed in Buyer’s purchase order or other documents which are inconsistent with, or in addition to, these Terms. 2. Prices; Payment Terms. All prices stated are current, subject to change with out notice by Omron. Omron reserves the right to increase or decrease prices on any unshipped portions of outstanding orders. Payments for Products are due net 30 days unless otherwise stated in the invoice. 3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices sent to Buyer after deducting transportation charges, taxes and duties, and will be allowed only if (i) the invoice is paid according to Omron’s payment terms and (ii) Buyer has no past due amounts. 4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 5. Orders. Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all costs involved in, obtaining any government approvals required for the impor tation or sale of the Products. 7. Taxes. All taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on Omron or required to be collected directly or indirectly by Omron for the manufacture, production, sale, delivery, importa tion, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Omron. 8. Financial. If the financial position of Buyer at any time becomes unsatisfactory to Omron, Omron reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Omron may (without liabil ity and in addition to other remedies) cancel any unshipped portion of Prod ucts sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts. 9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Omron against all related costs or expenses. 10. Force Majeure. Omron shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron: a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship except in “break down” situations. b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall constitute delivery to Buyer; c. All sales and shipments of Products shall be FOB shipping point (unless oth erwise stated in writing by Omron), at which point title and risk of loss shall pass from Omron to Buyer; provided that Omron shall retain a security inter est in the Products until the full purchase price is paid; d. Delivery and shipping dates are estimates only; and e. Omron will package Products as it deems proper for protection against nor mal handling and extra charges apply to special conditions. 12. Claims. Any claim by Buyer against Omron for shortage or damage to the Products occurring before delivery to the carrier must be presented in writing to Omron within 30 days of receipt of shipment and include the original trans portation bill signed by the carrier noting that the carrier received the Products from Omron in the condition claimed. 13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL 14. 15. 16. 17. 18. ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or oth erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli gation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsi ble for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were prop erly handled, stored, installed and maintained and not subject to contamina tion, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Compa nies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environ ments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron247.com or contact your Omron representative for pub lished information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and their employees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, inves tigation, litigation or proceeding (whether or not Omron is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. Without limiting the foregoing, Buyer (at its own expense) shall indemnify and hold harmless Omron and defend or set tle any action brought against such Companies to the extent based on a claim that any Product made to Buyer specifications infringed intellectual property rights of another party. Property; Confidentiality. Any intellectual property in the Products is the exclu sive property of Omron Companies and Buyer shall not attempt to duplicate it in any way without the written permission of Omron. Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of Omron. All information and materials supplied by Omron to Buyer relating to the Products are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. Export Controls. Buyer shall comply with all applicable laws, regulations and licenses regarding (i) export of products or information; (iii) sale of products to “forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of regulated technology or information. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right and no course of dealing between Buyer and Omron shall operate as a waiver of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder without Omron's written consent. (c) Law. These Terms are governed by the law of the jurisdiction of the home office of the Omron company from which Buyer is purchasing the Products (without regard to conflict of law princi ples). (d) Amendment. These Terms constitute the entire agreement between Buyer and Omron relating to the Products, and no provision may be changed or waived unless in writing signed by the parties. (e) Severability. If any provi sion hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. (f) Setoff. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. (g) Definitions. As used herein, “including” means “including without limitation”; and “Omron Compa nies” (or similar words) mean Omron Corporation and any direct or indirect subsidiary or affiliate thereof. Certain Precautions on Specifications and Use 1. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Prod uct in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases but the following is a non-exhaustive list of applications for which particular attention must be given: (i) Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Prod uct. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO 2. 3. 4. 5. ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitabil ity and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our prac tice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifica tions of the Product may be changed without any notice. When in doubt, spe cial part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com OMRON CANADA, INC. • HEAD OFFICE Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com OMRON ARGENTINA • SALES OFFICE Cono Sur • 54.11.4783.5300 OMRON ELECTRONICS DE MEXICO • HEAD OFFICE México DF • 52.55.59.01.43.00 • 01-800-226-6766 • email@example.com OMRON CHILE • SALES OFFICE Santiago • 56.9.9917.3920 OMRON ELECTRONICS DE MEXICO • SALES OFFICE Apodaca, N.L. • 18.104.22.168.99.20 • 01-800-226-6766 • firstname.lastname@example.org OTHER OMRON LATIN AMERICA SALES 54.11.4783.5300 OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu Authorized Distributor: Automation Control Systems • Machine Automation Controllers (MAC) • Programmable Controllers (PLC) • Operator interfaces (HMI) • Distributed I/O • Software Drives & Motion Controls • Servo & AC Drives • Motion Controllers & Encoders Temperature & Process Controllers • Single and Multi-loop Controllers Sensors & Vision • Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors • Amplified Photomicrosensors • Measurement Sensors • Ultrasonic Sensors • Vision Sensors Industrial Components • RFID/Code Readers • Relays • Pushbuttons & Indicators • Limit and Basic Switches • Timers • Counters • Metering Devices • Power Supplies Safety • Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety Controllers • Light Curtains • Safety Relays • Safety Interlock Switches T63I-E-01 05/16 Note: Specifications are subject to change. Printed on recycled paper. © 2016 Omron Electronics LLC Printed in U.S.A.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project