RINS1405-1 TMD15 Internal EXP

RINS1405-1 TMD15 Internal EXP
Coverage Pattern And Plan View
HORIZONTAL COVERAGE
VERTICAL COVERAGE
Maximum Range Setting
Security Grade 3
Environmental Class 2
2.4m
6ft 6”
15m
®
TS50131-2-4
EN50131-1
PD6662:2004
INTERNATIONAL
®
TMD15 Specifications
2m
4m
6m
8m
10m
12m
15m
12m
Minimum Range Setting
2.4m
6ft 6”
10m
®
Model:
TMD 15 15m Internal detector
Colour:
WHITE
Casing:
3mm ABS, 0.4mm HDPE in Lens Area
Lenses:
2 Volumetric Lenses, with NO
overlapping zones
Detection Method:
2 Low noise dual element passive infrared
sensors and a microwave doppler unit
Dual Tech Sensitivity:
Selectable AUTO or HIGH
Temperature Compensation:
Digital
Microwave Detection Range:
15m PIR and 1-15m microwave
anti-mask Detection Range:
0m - 1m anti-masking
Detection Zones:
27 facets,54 zones in total.
Top Lens: 5 columns, 15 facets, 30 zones
90 field of view none-overlapping zones
Bottom Lens: 4 columns, 12 facets, 24 zones
69 field of view none-overlapping zones
Detection Speed:
0.25 - 2.5m/s
Operating Voltage:
9-16Vdc, 13.8Vdc typically
Current Consumption:
24mA @ 13.8Vdc Quiescent
Relay Output:
3 x SELV limits; 60Vdc 50mA (42.4Vac peak)
Mounting Height:
1.8 - 2.4m = 15m.
Tamper Switch:
12Vdc 50mA both front and rear
Storage Temperature:
-40 C to +80 C (-40 F to +176 F)
Operating Temperature:
-30 C to +70 C (-22 F to +158 F)
Emissions:
EN55022 Class 2
Immunity:
EN50130-4
8m
2m
6m
4m
6m
8m
10m
12m
15m
Dual Tech Lens
Volumetric
90
30 Zones
3 Planes
4m
2m
15m
50ft
Dual Tech
PIR
PIR Lens
Volumetric
69
24 Zones
3 Planes
3mm
(0.12")
Operation of Features
Switch 4. RI 1 Mode
A link on board marked “RI1/Spare” determines if the RI1 terminal is used for the
set/unset signalling or simply as a spare terminal to aid EOL wiring.
If the RI1/Spare link is fitted, the state of RI1 determines if the panel is set or unset.
The actions that can be performed in set and unset mode are also determined by
DIP switch 4 and 2. DIP switch 4 controls the action of RI1. If the switch is ON the
detector will operate permanently in Set Mode. When DIP switch 4 is OFF, the
detector will use the state of RI1 to determine the set or unset state.
Self Test
A 0V applied to input RI1 is interpreted as being unset.
Every 5 hours of detector none activity the detector will do an active diagnostic self
A +12V applied to input RI1 is interpreted as being set.
test. If in the unlikely event of a failed self test the detector anti-mask/fault relay will open.
DIP switch 2 determines if anti-masking is enabled all of the time or only when the panel
Low Voltage Detect
is unset. When nothing is connected to RI1, the input state is in the set state.
If the detector detects a low voltage fault, then the anti-mask/fault relay will open
Switch 5. Dual Tech (Alarm 1) Sensitivity
The EN anti-mask Operation
ON = Auto Sensitivity / OFF = High Sensitivity
FOR EN OPERATIONS DIP SWITCH 6 MUST BE ON
The bottom PIR will always remain in Auto Sensitivity
®
If an attempt is made to anti-mask the TMD15G3 the BLUE LED will start flashing at
Switch 6. Anti-anti-mask Relay Action
half a second intervals, signaling that the detector is going into ‘anti-mask processing’.
FOR EN OPERATION DIP SWITCH 3 MUST BE OFF
anti-mask processing will take 60 seconds to complete.
ON = Open Both anti-mask and Alarm Relays
If the detector still sees a anti-mask after 60 seconds then the anti-mask/fault and
Example of a control panel input looking for a anti-mask value of 13k7. See below
Alarm relays open, and the GREEN and ORANGE LEDs will be illuminated.
For None EN operation just the anti-mask/fault relay goes open.To select which relays to Alarm relay = 4k7, Tamper EOL = 2k2, anti-mask/Fault relay = 6k8.
open on a anti-mask activation see dip switch 6.To reset the detector to normal operating None EN operation only anti-mask relay opens.
OFF = Opens anti-mask Relay Only
mode, remove the blocking material, the BLUE LED will then flash again and during
Example of a control panel input looking for a anti-mask value of 14k2. See below
this time the detector should be walk tested to activate both Microwave and PIR, the
Alarm relay = Closed, Tamper EOL = 2k2, anti-mask/Fault relay = 12K.
GREEN and ORANGE LED will distinguish after 60 seconds and the relays will be
closed again.If the detector has been put into anti-mask processing by accident, you will Switch 7. Operational mode
need to walk test the detector so both the Microwave and PIR trigger, after 60
ON = TMD Mode.
seconds the BLUE LED will stop flashing and normal operation is resumed.
DIP Switch 7 determines the operational mode of the detector. When the switch is
Switch 1. 50/60Hz
ON (default) will operate as a TMD15G3 ®, where the Dual Tech and the Single PIR
operate independently.
ON = 50Hz
OFF = 60Hz
To open alarm contact 1, the Dual Tech’s PIR must trigger within a given time period
Switch 2. Anti-anti-mask Mode
of the microwave sensor. Alarm contact 2 is based on the operation of the Single PIR
This controls when the anti-masking algorithm is applied. When the DIP switch is ON only.
(Default), the anti-masking algorithm is enabled regardless of the set/unset status of
OFF = TriCover ® Detector Mode.
the detector. When the DIP switch is OFF, the anti-masking algorithm is enabled when When switch 7 is OFF, the detector will operate as a TriCover ® detector, with
the RI1 is in the unset state.
all technologies needing to trigger within a given time period of each other to open
alarm contact 1. Alarm contact 2 will operate in the inverse of alarm contact 1.
Switch 3. Blocking
In alarm, the only LED to be illuminated will be the Dual Tech alarm LED.
ON = Blocking Disabled / OFF = Blocking Enabled
‘Blocking’ works as follows: If an attempt to anti-mask the detector is made when the Switch 8. LED Enable/Disable
control panel is disarmed, the alarm relay will be held open until the anti-masking is
ON = LED Enable / OFF = LED Disable
removed (thus not allowing the control panel to arm). You must also connect the
To remotely enable the LEDs 0V must be applied to the “LED” terminal.
®
“RI 1” input on the TMD15G3 to a programmable output. When the control panel
If used with Pyronix panels, the LED terminal must be connected to a PGM
is disarmed, this input must be at 0V. When the panel is armed it must be at 12V.
output and programmed as “Remote LED Enable”.
To enable this feature dip switch 3 must be OFF.
For Standard G3 operations the DIP switches do not need to be adjusted.
Initial Power Up
®
On first power up of the TMD15G3, the detector will go into a self test, this will
involve the GREEN and ORANGE LEDs flashing on the dual tech, and the RED
LED flashing on the PIR. After a minute the detector will be ready.
If the ORANGE LED is still flashing then the detector has failed a Microwave test,
or if the GREEN LED or RED LED is still flashing then the detector has failed a PIR
test, if this occurs try restarting the detector (powering down and back up).
3m = 12m
Suggested Specification Detail:
A dual technology (PIR/Microwave) movement detector having a range capability
of 15 metres and five detection columns within an overall angle of coverage of 90
degrees. This is non-overlapping with a PIR movement detector, which has a
range capability of 15 metres and four detection columns with an overall angle of
coverage of 69 degrees installed in the (location) and at a height of (x) metres.
Switch Options
SWITCH
1
2
FEATURE
50/60Hz
Anti anti-mask
POSITION MEANING
ON
50Hz
OFF
60Hz
ON
24 Hour
OFF
Anti-anti-mask only enabled in
ON
Blocking processing Off
unset mode
3
Blocking
OFF
Blocking processing On
4
RI1 Mode
ON
Permanent in Set Mode
OFF
State of Ri1 = set/unset mode
5
Sensitivity
ON
Dual Tech = AUTO
OFF
Dual Tech = HIGH
6
anti-mask
ON
Open anti-mask & Alarm relays
when in anti-mask
OFF
Open anti-mask relay only when
Operational
ON
Two movement detector
Mode
OFF
TriCover ® detector
LED Enable
ON
Enable LEDs
OFF
Disable LEDS
in anti-mask
7
8
INTERNATIONAL
This product is approved for use in the Residential,
Commercial and Light Industrial Environment.
TS50131-2-4
EN50131-1
PD6662:2004
Security Grade 3
Environmental Class 2
This product complies with TS50131-2-4. at security grade 3,
environmental class 2.
UK = Suitable for use with systems installed to PD6662:2004 (AMD)
EXPORT = Suitable for use with systems installed to EN50131-1
Customer Support Line (UK only):
+44(0)845 6434 999 or or +44(0)1709 535225
Hours: Mon to Fri, 8:00am till 6:30pm
Email: customer.support@pyronix.com
Website: www.pyronix.com
Pyronix Limited, Pyronix House, Braithwell Way,
Hellaby, Rotherham, S66 8QY. UK
WARRANTY
This product is sold subject to our standard warranty
conditions and is warranted against defects in
workmanship for a period of five years.
In the interest of continuing improvement of quality,
customer care and design, Pyronix Ltd reserves the
right to amend specifications, without giving prior
notice.
RINS1405-1
The Tampers
Wall Mounting
Front Tamper
+
+
Back Tamper
Case Lid
Screw
-
TAMPER
EOL
ALARM 1
5K6
4K7
2K2
1K
anti-mask/FAULT
3K
15K
12K
8K2
6K8
KS
4K7
2K2
1
2
3
4
5
6
7
8
1K
Casing Knockouts
The back tamper operates by the use of the “rear
®
tamper break out” section of the TMD 15. If the
detector is forcibly removed the “rear tamper
break out” stays attached to the wall, thus opening
the back tamper.
Rear Tamper
Break Out
(See “The
Tamper”
section)
DIP
Switches
MW Range Adjust
Off
®
NOTE: When mounting the TMD 15,
ensure that it is mounted vertically
50Hz
ON
24 Hour
ALARM 2
8
7
6
5
4
Set Mode
Blocking Off
Dual Tech High Sensitivity
RI 1 Mode
3
Dual Tech Auto Sensitivity
Open Mask Relay
Blocking On
TAMPER
1K
Pyro Sensor
3K
15K
12K
8K2
6K8
ON
5K6
KS
Microwave
Module
4K7
1
2K2
2
3
4
5
6
7
8
Anti-mask Adjust
Increase
Decrease
Sensitivity
Sensitivity
(1m)
(0m)
Decrease
Sensitivity
(1m)
1K
(Must be at 0.1m - 1m
to be EN compliant)
5K6
Increase
Sensitivity
(15m)
FULLY ANTI-CLOCKWISE
TURNS THE anti-mask OFF
4K7
2K2
1K
Pyro Sensor
MW Range Adjust
2
Open Mask & Alarm Relays
anti-mask only in unset
1
KS
2 Movement Detector
2K2
Microwave Adjust
2K2
6K8
Disable LEDs
TriCover ® Detector
5K6
4K7
AM Adjust
5K6
4K7
0
Enable LEDs
Anti-mask EOL
Header
Disabled
Enabled
1K
PIR
Range:
5, 10 or 15m
(15m top)
Dip Switches
On
anti-mask/FAULT EOL
2K2
1K
TAMPER
Wall Fixing
Knockouts
RI1/Spare
4K7
6K8
ALARM 1
EOL Resistance
Headers
Dual Tech
(TAMPER,
ALARM 1,
anti-mask/FAULT)
6K8
5K6
ALARM 1 anti-mask/FAULT
RI 1 LED ALARM 2
EOL
EOL
EOL EOL
RI 1 / SPARE
anti-mask/FAULT
anti-mask/FAULT EOL
1K
ON
TAMPER
EOL
5K6
RI 1 / SPARE
5K6
4K7
2K2
-
LEDs
Left = Orange (Microwave)
Center = Blue (Alarm)
Right = Green (PIR)
ALARM 1 anti-mask/FAULT
RI 1 LED ALARM 2
EOL
EOL
EOL EOL
60Hz
The ‘notches’ as shown above, alter the range
of the PIR from 5m to 15m.
EOL Resistance
Headers
Single PIR
(TAMPER,
ALARM 2)
Top = 15m
Middle = 10m
Bottom = 5m
TAMPER
Make sure a
10mm gap exists
between the ceiling
and the top of the
TMD before fixing.
10mm
Physical Layout
PIR Range
AM Adjust
5K6
4K7
2K2
1K
Front
Tamper
0
6K8
ALARM 2
Case Lid Screw Fitting
®
TAMPER
The Installation Of The TMD15
5K6
4K7
2K2
LED
Red (Alarm)
1K
®
The Wiring Connections For The TMD15 (Examples)
Grade 3 Configuration (DEOL)
TriCover® mode configured to a single input with anti-mask
configured to a second input
NOTE: DIP SWITCH 7 MUST BE OFF
Grade 2 Configuration
TriCover® Mode SEOL Wired to a single input with anti-mask
configured to a second input
NOTE: DIP SWITCH 7 MUST BE OFF
Dual Tech
Grade 2 Configuration
Dual Tech and Single PIR Technologies
Configured To Separate Inputs (SEOL)
Dual tech to input 1
Single PIR to input 2
Dual Tech
Dual Tech
2K2
ALARM 1
4K7
2K2
1K
15K
15K
anti-mask/FAULT
12K
8K2
6K8
5K6
4K7
+
-
TAMPER
EOL
TAMPER
ALARM 2
RI 1 / SPARE
1K
2K2
1K
8K2
6K8
5K6
4K7
2K2
1K
1K
+
-
TAMPER
EOL
RI 1 LED ALARM 2
ALARM 1 anti-mask/FAULT
EOL
EOL
EOL EOL
Single PIR
Single PIR
2K2
4K7
5K6
4K7
ALARM 1 anti-mask/FAULT
RI 1 LED ALARM 2
EOL
EOL
EOL EOL
5K6
5K6
8K2
6K8
2K2
4K7
0
12K
12K
ANTI-MASK
FAULT EOL
LINK MUST
BE OFF
5K6
4K7
2K2
RI 1 / SPARE
TAMPER
1K
anti-mask/FAULT
3K
15K
6K8
MASK/FAULT EOL
Z2
2K2
3K
Single PIR
ANTI-MASK
FAULT EOL
LINK MUST
BE OFF
1K
5K6
3K
1K
RI 1 LED ALARM 2
ALARM 1 anti-mask/FAULT
EOL
EOL
EOL EOL
RI 1 / SPARE
+AUX- Z1
5K6
2K2
6K8
1K
6K8
MASK/FAULT EOL
5K6
4K7
2K2
1K
5K6
4K7
2K2
1K
0
0
ANTI-MASK
FAULT EOL
LINK MUST
BE OFF
NOTE: IF THE RESISTOR VALUES THAT YOU REQUIRE ARENT SHOWN, PLEASE CONTACT CUSTOMER SUPPORT.
6K8
MASK/FAULT EOL
ALARM 2
-
6K8
4K7
TAMPER
+
1K
4K7
1K
2K2
TAMPER
EOL
2K2
COM
TAMPER
Z2
4K7
ALARM 2
ALARM 1
Hard Wired
Resistor
(This example
would be 4k7)
+AUX- Z1
5K6
4K7
Hard Wired
Resistor
(This example
would be 4k7)
ALARM 1
1K
COM
TAMPER
2K2
6K8
Z2
anti-mask/FAULT
COM
+AUX- Z1
TAMPER
5K6
5K6
5K6
4K7
5K6
4K7
2K2
1K
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising