Edelbrock LS7 Corvette Supercharger

Edelbrock LS7 Corvette Supercharger
Edelbrock LS7 Corvette Supercharger
Part #1572 & 1573
FOR VEHICLES NOT EQUIPPED WITH AUX. OIL COOLER,
DRILL HOLES MARKED B
FOR VEHICLES EQUIPPED WITH AUX. OIL COOLER,
DRILL HOLES MARKED A.
LH
A
1.00
A
B
A
0.35
1.00
A
0.35
B
LINE UP TEMPLATE TO SHROUD
USING THESE FEATURES
0.35
1.38
TEMPLATE, FAN SHROUD,
C6 CORVETTE, LH
RH
TEMPLATE, FAN SHROUD,
C6 CORVETTE, RH
A
1.38
0.35
A
DRILL HOLES MARKED A FOR ALL VEHICLES
LINE UP TEMPLATE TO SHROUD
USING THESE FEATURES
11
11
2
4
15 64
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
INTRODUCTION
Thank you for purchasing the Edelbrock 7.0L GM Supercharger System for the Chevy Corvette Z06. The Edelbrock E-Force
Supercharger System for the 2006 to 2010 Corvette Z06 (not compatible with ZR1 or base models) utilizes Eaton’s new
Gen VI TVS Supercharger rotors, featuring a four lobe design with a full 160°. of twist for maximum flow, minimum
temperature rise, quiet operation, and the reliability for which Eaton is known. The Edelbrock Supercharger is a complete
system that maximizes efficiency and performance by minimizing air restriction into, and out of, the supercharger. This
results in maximum airflow, with minimal temperature rise and power consumption. The supercharger housing itself is
integrated into the intake manifold for a seamless design with minimal components, eliminating the possibility of vacuum
leaks between gasket surfaces. The system also utilizes a front drive, front inlet configuration giving it the shortest, least
restrictive inlet path on the market. The supercharger is inverted, expelling the air upward. Air pressure then builds in
the plenum, before being drawn down through each of two intercooler cores, oriented horizontally, next to, and below the
supercharger outlet. After passing through the intercooler cores, the air travels through the long 12” runners, which route
underneath the supercharger housing to the cylinder head ports, in a horizontal, nested configuration. The upper plenum
area is enclosed by a top cover that has been designed to provide an appealing and distinctive under-hood appearance.
This configuration allows for a compact package that can fit under the stock hood and cowl of the C6 Corvette, without
sacrificing runner length, or intercooler area. The E-Force supercharger features a uniquely styled plenum, and includes
matching side covers. The Edelbrock supercharger provides neck snapping performance that is safe to operate on a
completely stock engine. It is 50-state emissions legal, and can be had with an optional 5-year 100,000 mile warranty
so that there are no worries when installing it on a brand new car.
TOOLS AND SUPPLIES REQUIRED
l Jack and Jack Stands
OR Service Lift
l Panel Puller
l Ratchet and Socket Set including: 7mm, 8mm, 10mm
(standard, deep and universal), 11mm, 12mm (deep),
13mm, 15mm, 18mm, 21mm (deep), 24mm
l Wrenches including: 8mm, 18mm, 27mm
l 18mm Line Wrench
l 12” Ratchet Extension Bar
l 1/2” Breaker Bar
l Flat Blade & Phillips Screwdrivers
l Compressed Air
l Torx-20 Driver
l Allen Wrenches including: 5mm, 6mm, 8mm
l 2” Long 6mm Allen Socket
l 3/8” Fuel Line Removal Tool
l Torque Wrench
l Needle Nose Pliers
lPliers
OR Hose Clamp Removal Tool
l Pneumatic or Power Drill
l Impact Wrench
l Loctite 609 Retaining Compound or equivalent
l O-ring Lube
lAnti-seize
l Masking Tape
l DT-47731 Transmission Cooler Quick Disconnect Tool
l J-42188 Ball Joint Separator
l J-42386-A Flywheel Holding Tool
Edelbrock LLC, 2700 California Street, Torrance, CA 90503
Toll-Free Tech Line: 1-800-416-8628 Office/Sales Line: 310-781-2222
©2012 Edelbrock LLC
Part #1572 & 1573
Page 1
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
IMPORTANT WARNINGS
Before beginning installation, use the enclosed checklist to verify that all
components are present in the box then inspect each component for damage
that may have occurred in transit. If any parts are missing or damaged, contact
Edelbrock Technical Support (800-416-8628), not your parts distributor.
WARNING: Installation of this supercharger will result in a significant change to the
performance characteristics of your vehicle. It is highly recommended that you take some
time to familiarize yourself with the added power, and how it is delivered, in a controlled
environment. Take extra care on wet and slippery roads, as the rear tires will be more likely
to lose traction, with the added power. It is never recommended to turn off your vehicles
traction control system.
Proper installation is the responsibility of the installer. Improper installation will void all manufacture’s
standard warranties and may result in poor performance and engine or vehicle damage.
Due to the complexity of the Edelbrock E-Force Supercharging system, it is recommended that this system only be
installed by a qualified professional with access to a service lift, pneumatic tools, and a strong familiarity with automotive
service procedures. To qualify for the optional supplemental warranty, it is necessary to have this system installed by
a Certified ASE Technician, GM Dealership, or an Authorized Edelbrock Installer. Failure to do so will void and/or disqualify
any and all optional supplemental warranties offered with this system. Please contact the Edelbrock Technical Support
department if you have any questions regarding this system and/or how your installer of choice will affect any warranty
coverage for which your vehicle may qualify.
Any previously installed aftermarket tuning equipment must be removed and the vehicle returned to an as
stock condition before installing the supercharger.
Any equipment that directly modifies the fuel mixture or ignition timing of the engine can cause severe engine damage if
used in conjunction with the Edelbrock E-Force Supercharger System. This includes, but is not limited to: ignition boxes,
air/fuel controllers, OBDII programmers, and any other device that modifies signals to and/or from the ECU. Aftermarket
bolt-on equipment such as underdrive pulleys or air intake kits will also conflict with the operation of the supercharger
and must be removed prior to installation. Use of any of these products with the E-Force Supercharger could result in
severe engine damage.
91 octane or higher gasoline is required at all times. If your vehicle has been
filled with anything less, it must be run until almost dry and refilled with 91
or higher octane gasoline twice prior to installation.
Failure to use the required 91 octane gasoline or higher could permanently
damage your engine. Any failures associated with not using premium 91
octane gasoline or higher, will be ineligible for warranty repairs.
Edelbrock periodically releases improved versions of the calibration file found on the supplied handheld
programmer. Check the website to ensure you have the latest version, as described in step #228.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 2
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
INSTALLATION HARDWARE IDENTIFICATION GUIDE
Bag #1
(2x) - M8 Washer
(3x) - M8 x 1.25 x 20mm
Hex Flange Bolt
(1x) - M10 x 1.5 x 75mm Hex Flange Bolt
(3x) - M8 x 1.25 x 90mm Hex Flange Bolt
(1x) - M10 x 1.5 x 45mm Socket Head Bolt
Bag #2
(1x) - M8 x 1.25 x 30mm Hex Flange Bolt
(3x) - M6 x 1 x 16mm Hex Flange Bolt
(2x) - M6 x 1 x 20mm Hex Flange Bolt
(6x) - 3/4” Hose Clamp
(1x) - Nylon Body Pin
(1x) - M8 x 1.25 x 25mm Hex Flange Bolt
(1x) - Lower Intercooler Reservoir Bracket
(2x) - 1/2” Hose Clamp
(2x) - 1-3/4” Worm Clamp (1x) - 3/4” Worm Clamp
(Not to Scale)
(Not to Scale)
(1x) - Upper Intercooler Reservoir Bracket
©2012 Edelbrock LLC
Part #1572 & 1573
Page 3
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
Bag #3
(11x) - M8 x 1.25 x 25mm
Countersunk Socket Head Bolt
(8x) - M6 x 1 x 45mm
Hex Flange Bolt
(4x) - M6 x 1 x 12mm
Socket Head Bolt
(2x) - M6 x 1 x 16mm
Button Head Bolt
Bag #4
(1x) - GM Factory Harmonic Balancer Bolt
(1x) - M16 x 2 x 120mm Hex Bolt
Ream Hole
Drill Hole
Bolt Hole
(1x) - 1/4” x 3/4” Steel Dowel
(1x) - Crank Pinning Drill Guide
(1x) - 15/64” High Speed Steel Drill Bit
(1x) - .2500” Reamer
©2012 Edelbrock LLC
Part #1572 & 1573
Page 4
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
Bag #5
(1x) - Barbed Quick Connect Fitting
(1x) - Air Inlet Tube PCV Grommet
(2x) - Air Inlet Tube Retainer Grommet
Bag #6
(1x) - Coil Cover Dipstick Grommet
(4x) - Coil Cover Bracket
(4x) - Coil Cover Retainer Stud
(4x) - Coil Cover Standoff
©2012 Edelbrock LLC
Part #1572 & 1573
Page 5
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
HOSE IDENTIFICATION GUIDE
Oil Cooler Outlet
Intercoolers to Reservoir
Reservoir to
Water Pump
Oil Cooler Inlet
Heat Exchanger to Intercoolers
Water Pump to
Heat Exchanger
Valve Covers to
Dry Sump (rear)
Manifold to EVAP Solenoid
PCV
Brake Booster
Air Inlet to Dry
Sump (front)
EVAP Solenoid
to Firewall
AUX Dry Sump
& Tee
©2012 Edelbrock LLC
Part #1572 & 1573
Page 6
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
DRY SUMP ROUTING GUIDE
2009 & Later
Vehicles Only
D
NOTE: The stock valley tray
baffle must be transferred to
the Edelbrock valley tray.
B
A
A: Air inlet to dry sump (Front)
B: Valve covers to dry sump (Rear)
C: PCV to fitting on bottom of air
inlet, behind throttle body.
D: Auxiliary hose & tee fitting: From
auxiliary dry sump tank to “B” hose.
C
©2012 Edelbrock LLC
Part #1572 & 1573
Page 7
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
WIRE HARNESS GUIDE
TMAP Sensor
Engine Harness
(Stock MAF Connector)
Engine Harness
(Stock MAP Connector)
EVAP Solenoid
MAF Sensor
Engine Harness
(Stock EVAP
Connector)
Relay
(Radiator Shroud)
Power Supply Wire
(Fuse Box Power
Stud)
Fuse
(Fuse Box Stud)
Ground Strap
(Passenger Side Grounding Stud)
Intercooler Water Pump
©2012 Edelbrock LLC
Part #1572 & 1573
Page 8
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
Test Flash Procedure
Use the supplied programmer to flash the ECU and verify
its compatibility.
• Use directional pad to highlight your vehicle and
transmission combination then press Select.
Original Equipment Manufacturers often release updates
to the computer programming for your vehicle. Edelbrock
highly recommends that you verify, with your new car
dealer, that your vehicle is equipped with the latest
software version from your vehicle manufacturer, before
attempting to load the Edelbrock tune.”
• It is recommended that you check the Edelbrock
website (http://www.edelbrock.com/automotive_new/mc/
superchargers/fuel_injected_soft-tech.shtml) to confirm
that you have the latest calibration. Once you have found
the latest tune on the site, power on the programmer, press
the left arrow and select the Device Info option. Scroll down
to Tune Version and compare that number to the one on the
site. If they are different, download the new calibration with
the supplied USB cable.
• Put the car into Acc mode by pressing and holding the
start button on the steering column. But don’t start the
vehicle.
• Use directional pad to highlight your vehicle and
transmission combination then press Select, again.
• Use directional pad to highlight Begin Program then press
Select.
• Vehicles equipped with a manual transmission will have
three separate operations take place during this step, while
vehicles with an automatic transmission will have five.
Completion of each operation will cause the progress bar
to reset to zero.
DO NOT unplug the programmer until prompted.
• Connect the supplied PCM cable to the OBD-II connector
located below the steering wheel in the passenger
compartment.
• Use directional pad to highlight Program Vehicle option
and press Select button.
• Use directional pad to highlight Pre-programmed Tune
option and press Select button.
• Read parting message from programmer then press
Select to continue.
• Read disclaimer then press Select to continue.
• Verify ignition is in the ‘Key On’ position but that the
engine is not running then press Select.
©2012 Edelbrock LLC
Part #1572 & 1573
• Turn the car off when prompted to do so by the handheld
programmer.
• Unplug the programmer cable from the OBD-II port.
In the rare occurrence that you encounter an error message
during the test flash procedure, please refer to pg. 33, titled
Email Edelbrock Your Stock PCM Calibration.
Page 9
Brochure #63-1572
Rev. 04/30/12
11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
Post Successful Test Flash
If you are ready to install the supercharger, proceed to Step
1 of the Supercharger Installation
3. Use a 7mm wrench to remove the four bolts retaining
fascia center.
OR
If you wish to return the ECU back to the factory calibration,
such that the vehicle can still be driven until you are ready
to begin the installation, then:
• Put the car into Acc mode, but don’t start the vehicle.
• Connect the supplied PCM cable to the OBD-II connector.
• Use directional pad to highlight Program Vehicle option
and press Select button.
• Use directional pad to highlight Return To Stock option
and press Select button.
• Follow the on screen instructions.
Turn the car off when prompted to do so by the handheld
programmer.
4. Lift and support the front end of the vehicle using a jack
and appropriately load rated jack stands then loosen and
remove the lug nuts from both front wheels. Remove the
wheels and set them aside.
5. Use a panel puller to remove the 3 body pins on each
side that retain the inner fender wells. (Note: Some trim
packages use screws in place of pins along outer edge.)
• Read parting message from programmer then press
Select to continue.
• Unplug the programmer cable from the OBD-II port.
• When you are ready to Install the supercharger, proceed
with Step 1 and you will be prompted to re-flash the ECU
towards the end of the installation procedure.
Supercharger Installation
1. Use a 10mm socket to loosen and remove the negative
battery terminals.
6. Pull back the inner fender well to access the two bumper
studs on each side. Use a 10mm deep socket to remove the
nuts.
2. Use a 10mm socket to loosen and remove the positive
battery terminals.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 10
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
7. Remove the 10mm bolt that retains the brake cooling
duct on each side then remove the ducts.
12. Remove four body pins (two on each side) by reaching
up through the bottom of the fascia.
8. Place a drain pan below the passenger side of the
vehicle, then remove the radiator petcock and allow the
coolant to drain into the pan. Reinstall the plug once the
cooling system has drained completely.
13. Place multiple layers of masking tape on the nose of
the hood as well as the portion of the front fascia directly
below the hood to protect from damage during removal.
9. Disconnect the indicator and fog lamp electrical
connectors.
10. Remove the three screws and one body pin that retain
each front valance. 11. Remove the five 7mm and two 10mm nuts retaining
the fascia from below.
©2012 Edelbrock LLC
Part #1572 & 1573
14. The sides of the fascia can be pulled away from the
clips holding it in place, then down off the studs. The
center section must be pulled up and over the nose section,
and the whole assembly pulled straight off and set aside.
15. Disconnect the Mass Airflow Sensor connector.
Page 11
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
16. Disconnect the PCV tube from the air inlet tube.
22. Disconnect the Electronic Throttle Control connector on
the passenger side of the throttle body.
17. Use a flat head screwdriver to loosen all three air inlet
worm clamps.
18. Pull out the splash shield above the air filter housings
then release the four clamps retaining the air box lids and
remove them along with the filters.
19. Compress the flex tube to remove it from the throttle
body and the MAF sensor then remove the sensor. Remove
the airbox assembly by lifting it off the retaining pins on
either side then pulling the air filter housings back to
separate them from the grommets on the front bumper.
20. Use a 15mm socket and a breaker bar to turn the
tensioner until the serpentine belt has enough slack to
remove it. 23. Use a 10mm socket to remove the four bolts holding in
the throttle body and set it aside. 24. Disconnect the ignition coil harness and O2 sensor
connectors then disconnect the spark plug wires from the
ignition coils.
25. Use a 10mm socket to remove the five bolts retaining
the coil bracket on each valve cover then remove both coil
bracket assemblies.
26. Use a fuel line removal tool to disconnect the fuel line
from the rails using a shop rag to absorb excess fuel.
21. Remove coil covers from valve covers by lifting up and
working fuel line through slot on driver side.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 12
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
27. Disconnect and remove the hose connecting the
passenger and driver side valve covers to the rear dry sump
tank fitting.
33. Disconnect MAP sensor electrical connector.
34. Disconnect the vacuum hose from the brake booster
fitting; it will be removed with the manifold.
28. Disconnect all eight fuel injector connectors.
29. Use a 10mm socket to remove the four fuel rail bolts.
NOTE: You will also need to remove one 8mm manifold
bolt and bracket before removing the fuel rails.
35. Disconnect and remove the two EVAP tubes located at
the front of the manifold.
30. Lift the injectors out of the manifold and work the rails
forward until they can be set aside.
31. Use a 10mm socket to remove the seven remaining
manifold bolts (out of ten).
36. Disconnect passenger side PCV tube from valley plate.
32. Disconnect the EVAP solenoid electrical connector.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 13
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
37. Remove the intake manifold and disconnect the small
vacuum hose at the rear of the manifold next to the larger
brake booster hose, if it is present. Leave this hose hanging
from the firewall as it will be reconnected later.
38. Use masking tape to cover the exposed intake ports on
the cylinder head.
44. Use a small flathead screwdriver to remove the eight
O-ring seals from the stock valley plate and install them in
the new valley plate. Remove the bolts retaining the stock
oil baffle to the stock valley plate then use a small
screwdriver to pry off the baffle. Clean any remaining
silicone off the mating flange, apply fresh silicone then
install the stock baffle onto the underside of the new valley
plate using the stock bolts coated with blue LocTite.
39. Remove the O-ring port gaskets from the stock intake
manifold and set them aside for reuse later.
40. Use a 15mm socket to remove the two bolts retaining
the belt tensioner.
45. Apply anti-seize to the tapered surface beneath the
heads of the countersunk bolts supplied in Bag #3 and
install the valley plate along with the stock perimeter
gasket. Tighten the bolts from the center out with a
5mm allen tool. Give the bolts a second pass in the same
sequence and torque them to 18 ft-lbs.
41. Disconnect the oil pressure sensor electrical connector
at the rear of the valley plate.
42. Use a 27mm wrench to remove the oil pressure sensor
from the rear of the valley plate.
46. Install the oil pressure sensor into the supplied valley
plate with thread sealant and a 27mm wrench. Torque the
sensor to 15 ft-lbs.
47. Reconnect the oil pressure sensor electrical connector
at the rear of the valley plate.
48. Use a 15mm socket to remove the bolt retaining the
EVAP solenoid.
43. Clear engine valley of all debris then use a 13mm
socket to remove the 11 bolts retaining the valley plate and
remove it.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 14
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
49. Use a 10mm socket to remove the four bolts (two on
each side) retaining upper radiator shroud and remove it.
50. Drain the engine oil from the oil pan and remove the
oil filter.
51. Use the DT-47731 Transmission Cooler Quick
Disconnect Tool to detach two oil lines from the oil cooler.
52. Remove the two bolts on the driver side holding the oil
cooler to the shroud.
56. Use a hand siphon to drain the power steering fluid
reservoir.
57. Disconnect the power steering lines from the power
steering cooler.
58. Remove the three bolts retaining the power steering
cooler then remove the cooler.
59. Disconnect the alternator electrical connector.
53. Remove the nut holding the oil cooler bracket to the
shroud and remove the cooler.
54. Trace the oil cooler lines back to the oil pan and
disconnect them, then remove the lines as a single
assembly. The bolts can then be discarded.
55. Disconnect the radiator fan electrical connector then
use a 10mm socket to remove the two bolts retaining the
fan assembly. Pull the hoses from the six clips holding
them to the assembly and remove the fan from below.
©2012 Edelbrock LLC
Part #1572 & 1573
60. Use a 13mm socket to remove alternator power wire.
61. Use a 15mm socket to remove the two alternator
support bolts, and then remove the alternator.
WARNING: With the wheels of the vehicle facing straight
ahead, secure the steering wheel with a steering column
anti-rotation pin, steering column lock or strap. Failure
to do so may result in damage to or a malfunction of the
airbag deployment system.
Page 15
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
62. Use an 11mm socket and an extension bar to remove
the bolt securing the steering column to the rack then pull
the intermediate shaft off the gear. Do not attempt to turn
the steering wheel until this bolt has been reinstalled.
66. Use a 13mm socket to remove the four bolts retaining
the stabilizer brackets.
67. Use a 13mm socket to remove the two nuts retaining
the brake pressure modulator valve.
63. Use a 6mm Allen tool to hold the tie rod ball stud
stationary while using an 18mm wrench to loosen the nut.
64. Use GM Ball Joint Separator #J 42188 to separate the
steering knuckle from the tie rod ball stud then remove the
tool and the nut. Use this procedure for both sides.
65. Remove the lower nut from the endlink by placing a
6mm wrench on the end of the stud while using an 18mm
wrench on the nut. Repeat the procedure for both sides.
©2012 Edelbrock LLC
Part #1572 & 1573
68. Place a catch pan below the steering gear then use an
18mm line wrench to disconnect the two power steering
lines from the steering gear. Page 16
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
69. Use a 10mm socket to remove the bolts retaining the
power steering line brackets or fluid cooler, if equipped. 75. Use a 13mm socket to remove the lower brake
modulator bracket bolts.
70. Use a floor jack to support the oil pan.
71. Use a 21mm deep socket to remove or loosen the two
front engine cradle bolts.
72. Disconnect the ride height sensor electrical connector
from each side, if equipped. 73. Use a 10mm socket to remove the driver side brake
line bracket bolt.
74. Use a 10mm socket to remove driver side ride height
sensor bolt, if it is present.
©2012 Edelbrock LLC
Part #1572 & 1573
76. Use an 18mm socket to remove the two steering rack
nuts and bolts.
77. Remove the plastic clamp holding the power steering
lines to the steering rack.
78. Loosen the rear engine cradle nuts with a 21mm deep
socket and lower them until there is a gap of 10mm from
the cradle to the top of the nut.
79. Insert a pry bar between the frame and front driver side
cradle mount.
80. Work the power steering rack out through the driver
side wheel well. Use the pry bar to widen the gap when
needed and push the brake lines out of the way to clear
the gearbox. Inserting a 5/16” nut on its side into the gap
between the cradle and the frame as a spacer may help.
Page 17
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
NOTE: The following six steps detail the process needed
to loosen and remove the crank bolt. Manual vehicles have
the option of placing a passenger in the car to put the car
in first gear and apply firm brake pressure while turning the
crank bolt in steps #84, 86, 87 & 89. Do not attempt this
optional procedure if the rear wheels are on the ground or
vehicle damage and/or injury could result.
81. Disconnect the oil level sensor electrical connector
from the passenger side of the oil pan. 84. Disconnect electrical connector at top of starter. 85. Use a 13mm socket to remove the nuts retaining
power wires to the starter.
86. Remove and set aside the starter and bracket.
82. Use a 10mm socket to remove the starter support
bracket bolt.
87. Install GM Flywheel Holding Tool #J-42386-A to prevent
the crank from rotating while loosening the balancer bolt
and torque the bolts holding it to 37 ft-lbs.
88. Use a breaker bar and a 24mm socket to loosen and
remove the crank bolt. A long pipe slid over the breaker bar
can be helpful for increasing leverage.
83. Use a 13mm socket to remove the two starter bolts.
89. Mark off with a piece of masking tape 1.6” from the tip
of the supplied drill bit.
90. Use a 24mm socket to install the supplied bolt and
reamer guide to the end of the crank.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 18
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
91. Lubricate the 15/64” bit supplied in Bag #4 with a small
amount of engine oil, then drill into the guide hole with a
bushing until the tape mark on the bit meets the guide.
Loosen the bolt and blow out any chips with compressed air
then turn the guide until the ream hole lines up with the one
just drilled in the crank and balancer. Use the back side of
the ream tool to verify that the holes line up then tighten the
bolt and use the .2500” reamer to ream the hole.
92. Use compressed air to clear out any metal shards in
the hole. Apply Loctite 609 retaining compound or
equivalent to the supplied crank pin then tap it into the
drilled hole until it is flush.
98. Route the longer output hose between the motor mount
and the block so that the open end is in the vicinity of the
upper radiator hose and the male tube is near the oil filter
mounting location. 99. Route the shorter input hose between the motor mount
and the block so that the male tube is close to the fitting
installed in the side of the block and the female end is near
the oil filter mounting location.
100. Slide the supplied oil cooler up to the flange directly
adjacent to the oil filter mounting location and connect the
input and output hoses. Ensure that the lock clips are fully
engaged to prevent the possibility of leaks.
93. Install the supplied GM crank bolt into the crank and
torque it to 37 ft-lbs, then rotate it an additional 140°.
101. Secure the oil cooler by tightening the bolts that
come with it into the flange on the oil pan, then install the
supplied bolt through the oil cooler assembly and thread it
into the bracket mounted to the oil pan rail.
94. Use a 17mm Allen socket to remove the threaded
freeze plug located on the driver side of the engine block
near the front of the engine.
102. Insert the male end of the input hose into the fitting
in the side of the block.
95. Install the supplied threaded fitting into the hole
previously occupied by the freeze plug.
103. Use the supplied zip ties to secure the wiring harness
away from any exhaust components or suspension parts.
96. Remove the wire harness holding clamp from the gap
between the driver side motor mount and the block.
104. Fill the oil filter with engine oil and install it in the
stock mounting location.
97. Remove the 3rd bolt back from the front on the driver
side of the oil pan. Orient the supplied oil cooler bracket
so that it will line up with the back of the oil cooler, then
secure it with the stock oil pan bolt and tighten it to 18
ft-lbs.
105. Slide the steering rack back into place and
reconnect the electrical connector.
©2012 Edelbrock LLC
Part #1572 & 1573
106. Use an 18mm socket to reinstall the steering rack
nuts and bolts then torque them to 74 ft-lbs.
Page 19
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
107. Install the supplied spacers between the subframe
and the mounting nuts. The spacers with two notches go
in the front while those with one notch go in the rear.
108. Snug the front crossmember nuts then use a utility
jack to lift the crossmember. Torque all four crossmember
nuts to 81 ft-lbs.
109. Use a 13mm socket and the stock bolts to reinstall
the brake modulator bracket then torque them to 20 ft-lbs.
110. Use a 13mm socket and the stock bolts to mount the
brake pressure modulator to the bracket and torque them
to 106 in-lbs.
120. Install the starter dust shield and bolt it in place.
121. Reattach the starter electrical connector and the
power wires. Torque the power wire nuts to 71 in-lbs.
Reinstall the starter then use a 13mm socket to torque the
two bolts that hold it in place to 37 ft-lbs.
122. Apply blue loctite to the threads of a 20mm bolt
supplied in Bag #1, then use a 12mm socket and the
supplied washer to mount the pulley on the new lower idler
bracket so that the open side of the pulley faces away from
the bracket, then torque the bolt to 18 ft-lbs. 111. Use a 10mm socket and the stock bolts to reinstall
the power steering and brake line brackets.
112. Use an 18mm line wrench to reinstall the power
steering pressure and return hoses to the steering gear
then torque the fittings to 20 ft-lbs.
123. Use a 10mm socket to remove the three bolts on the
passenger side of the water pump.
113. Use a 10mm socket to reinstall the driver side ride
height sensor then plug in the electrical connector.
114. Use a 13mm socket and the four stock bolts to
reinstall the stabilizer and the brackets supporting it then
torque the bracket bolts to 43 ft-lbs.
115. Use an 6mm and an 18mm wrench to reattach the
stabilizer bar end links to the control arms then torque the
nuts to 56 ft-lbs.
116. Use a 6mm Allen tool and an 18mm wrench to
reattach the tie rod ends to the control arm. Tighten the nut
to 22 ft-lbs. then rotate it an additional 120°.
124. Use a 2” long 6mm Allen socket and the three 90mm
bolts supplied in Bag #1 to install the lower idler bracket on
the water pump, then torque them to 18 ft-lbs.
117. Reinstall the locating clamp around steering rack.
118. Reattach the steering column to the rack then use an
11mm socket to torque the stock bolt to 20 ft-lbs.
119. Reinstall the alternator, attaching the power wire and
electrical connector then torque bolts to 37 ft-lbs.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 20
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
CAUTION: If your vehicle is equipped with the depicted
transmission cooler lines, then check clearance between
said lines and any moving components. If necessary, gently
hand-bend the lines to avoid interference.
128. Use a 15mm socket and the 75mm bolt supplied in
Bag #1 to install supplied tensioner on new bracket and
torque it to 37 ft-lbs.
129. Use a 12mm socket and a 20mm bolt supplied in Bag
#1 to mount the EVAP purge solenoid on the back of the
new tensioner bracket. 125. Use a 15mm socket and the two stock bolts to mount
the new tensioner bracket onto the water pump then torque
them to 37 ft-lbs.
126. Use an 8mm Hex tool to install the 45mm bolt
supplied in Bag #1 that retains the tensioner bracket to the
cylinder head and torque it to 37 ft-lbs.
130. Use a 15mm wrench to remove two bolts retaining
the power steering reservoir bracket. Use a pair of pliers or
hose clamp tools to disconnect the lower reservoir-topump hose. Note that it is not necessary to fully remove the
reservoir from the engine.
127. Apply blue loctite to the threads of a 20mm bolt
supplied in Bag #1, then use a 12mm socket and the
supplied washer to mount the pulley on the tensioner
bracket and torque it to 18 ft-lbs.
131. Slide the old bracket off the reservoir then install the
supplied bracket using a 15mm socket and the stock bolts.
Slide the power steering reservoir onto the new bracket and
reattach the lower reservoir to pump hose.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 21
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
132. Reinstall the power steering cooler using the stock
bolts then reattach the lines to the cooler.
137. Use a 10mm socket to remove center air dam bolt.
133. Use a 13mm socket to remove the bolt holding the
horn bracket in place. Remove and set aside the horns.
138. Use a 10mm socket to install the heat exchanger,
using the 20mm bolts supplied in Bag #2 on the side, and
the stock air dam bolt on the bottom. 134. Line up the supplied templates on the radiator shroud
and drill the appropriate holes.
139. Locate the water pump bracket on the inboard,
passenger side of the bumper support rail using the lower
mounting hole. Mark the rail through the upper mounting
hole of the water pump bracket.
140. Drill the bumper support rail in the location previously
marked using a 5/16” drill bit.
141. Use a 12mm socket to install the water pump in its
bracket and secure it with the supplied strap. 135. Reinstall the radiator shroud by sliding it into place
from below then hold it in place using the four stock body
pins (two up front, and one on each side).
136. Clip the passenger side sensor back into place and
reattach the ambient air temperature sensor connector.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 22
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
144. NOTE: This step only applies to customers who
received version (1) of the water pump brackets. Install
the supplied stand-off and lock nut onto the OE horn
bracket. Proceed by mounting that assembly, with the
supplied M6 x 10mm bolt, to the water pump bracket as
shown below.
142. Remove the passenger side lower body pin.
143. Use a 10mm socket to install the pump bracket using
the M6 x 45mm bolt and M6 nut on top and the M8 x 30mm
bolt on the bottom, all supplied in Bag #2.
145. Re-install the horns using the OE nuts. Be sure to
orient the horns so as to allow a little bit of slack in the
horn’s wiring harness. Warning: Do not mount the horns
with the opening facing up, as they will accumulate
condensation and cease working.
NOTE: There are two different water pump brackets:
Version (1) requires the use of your OE horn bracket.
Version (2) has an integrated horn bracket. You should have
received one of the two brackets; If your supercharger kit
includes bracket version (2), you may disregard Step 144.
OE Horn brkt.
Version (1)
©2012 Edelbrock LLC
Part #1572 & 1573
Version (2)
146. Use the supplied bit to drill a 15/64” hole in the
passenger side of the upper radiator shroud according to
the supplied template.
Page 23
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
147. Use a 10mm socket and the four stock bolts to
reinstall the upper radiator shroud then attach the relay off
the supplied water pump wire harness to the upper radiator
shroud using the supplied body pin. Open and close the
hood to verify the relay clears the hood strut. 148. Route the intercooler water pump wire harness
extending from the relay down to the intercooler water
pump and plug in the connector.
150. Install the short molded hose from the outlet of the
intercooler water pump to the heat exchanger inlet. Secure
the fittings with the supplied hose clamps.
151. Lower the heat exchanger hose assembly along the
driver side of the radiator shroud. 152. Connect the heat exchanger hose assembly to the
heat exchanger through the hole drilled in the shroud.
Secure the fitting with a hose clamp supplied in Bag #2.
149. Plug the male connector on the T-segment of the
harness into the EVAP solenoid then plug the factory EVAP
connector into the female connector on the T-segment.
153. Connect TMAP harness to TMAP sensor near rear of
manifold. ©2012 Edelbrock LLC
Part #1572 & 1573
Page 24
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
154. Use a 10mm socket and an extension bar to loosen
the two nuts securing the fuse box.
155. Use a 7mm socket to remove the fuse box bolt
located in the passenger side fender well.
158. Use a 10mm socket to loosen rear hood hold down
latch bolt on passenger side fender.
159. Install intercooler reservoir by working molded hose
down along the passenger side of the radiator to the water
pump inlet and secure the hose on the pump fitting with a
hose clamp supplied in Bag #2.
160. Slide intercooler reservoir brackets behind loosened
fuse box nut and hood hold down latch bolt. Use a 10mm
socket to torque them to 89 in-lbs.
161. Use a 10mm socket to mount fuse on fuse box stud.
Then use a 13mm socket to attach the harness power wire
to the main positive terminal.
156. Install long end of molded hose on intercooler
reservoir outlet so that the hose will extend out and then
turn down when the reservoir is held upright. Secure the
hose with a hose clamp supplied in Bag #2. 162. Use a 10mm socket to attach the ground wire to the
ground stud near the relay. 157. Use a 10mm socket to install the brackets supplied
in Bag #2 on the reservoir. The image above shows the
installed orientation.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 25
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
163. Reinstall the fender well fuse box bolt.
164. Install supplied 15/32” hose on brake booster and
secure fitting with a hose clamp supplied in Bag #2.
165. Install the stock O-ring port gaskets in the supercharger
manifold. 168. (Refer to the Dry Sump Routing Guide located on page
7 of this instruction booklet for a clear depiction of the hose
routing procedure described below.) Attach the dry sump
breather hose assembly to the driver side valve cover fitting,
then route the rest of the hose along the firewall and over to
the passenger side. Connect the middle hose section to the
passenger side valve cover provision and the straight fitting
to the rear dry sump tank fitting. If your vehicle is an ’09
or newer and is equipped with an auxiliary dry sump tank
behind the primary, cut the supplied dry sump hose near
the rear dry sump fitting and install the supplied tee adapter
in line with that hose. Route the short section of hose
extending from the tee adapter to the auxiliary tank fitting.
169. Remove the tape covering the intake ports. Since two
of the stock manifold bolt hole provisions in the cylinder
heads break into the crankcase and are not used with this
supercharger, install the two button head bolts supplied in
Bag #3 in the front passenger side and rear driver side bolt
holes to ensure a good seal. With the assistance of one
or more people, lift the supercharger assembly onto the
engine.
166. Install supplied Manifold to EVAP Solenoid Hose on
manifold fitting below hub snout.
170. Tilt the manifold back slightly to install the small
factory vacuum hose running from the driver side firewall
fitting on the small fitting on the driver side of the air inlet
and the brake booster hose onto the larger fitting then
secure the brake hose with a clamp supplied in Bag #2. If
the smaller hose is not present, leave the fitting capped.
167. Clear engine valley of any hoses, wires, tools, etc.
Lay the intercooler-to-reservoir tank hose in the engine
bay, routed along the firewall behind the oil pressure
sensor, and connect it to the intercooler reservoir inlet,
securing the fitting with a hose clamp supplied in Bag #2.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 26
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
171. Use a 10mm universal socket with an extension bar
to install the eight intake manifold bolts following the torque
sequence below. Torque the bolts to 4 ft-lbs in the first
pass, then to 7.5 ft-lbs in the second.
172. Connect the Manifold to EVAP Solenoid hose to the
outer EVAP solenoid fitting and EVAP Solenoid to Firewall
Hose to the inner EVAP solenoid fitting. Route the Solenoid
to Firewall hose beneath hub snout and along driver side
valve cover to firewall fitting and connect it.
176. Apply O-ring lube to the sealing ring of the four
supplied fuel rail fittings. Use a 3/4” wrench to install the
two straight hose fittings on the radiator side of each fuel
rail then install the plug in the firewall end of the passenger
side fuel rail and the U-shaped fitting on the firewall end of
the driver side rail. Orient the fitting close to the injector,
leaving room for the injector connector.
177. Apply O-ring lube to the lower seals of each of the
fuel injectors.
178. Attach the supplied fuel rail crossover line to the
fitting on the passenger side fuel rail.
179. Install the fuel rails by sliding the injectors down
into the manifold provisions and applying pressure until
the mounting holes in the rails line up with the manifold.
Slide the crossover hose under the snout and air inlet of
the supercharger as you install the passenger side rail then
connect it to the driver side fuel rail fitting.
180. Use a 5mm Allen tool to install the four fuel rail bolts
supplied in Bag #3 and torque them to 91 in-lbs. 173. Use a 3/8” Fuel Line Removal Tool to remove the fuel
input line from the firewall fitting.
174. Take the fuel injectors out of their boxes and remove
their protective covers.
175. Apply O-ring lube to the upper injector seals, then
slide the injectors into the rails so that the electrical
connectors face away from the mounting flange.
©2012 Edelbrock LLC
Part #1572 & 1573
181. Clip the heat exchanger hose assembly to both lower
fittings at the front of the supercharger manifold.
Page 27
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
182. Attach one end of the supplied PCV hose to the 90°
fitting below the air inlet on the manifold.
187. Tuck the fuel injector wiring harness and the EVAP
Solenoid to Firewall Fitting Hose between the valve cover
and manifold then use a 10mm socket and the ten stock
bolts to install both coil brackets on to the valve covers.
188. Attach the ignition coil connectors and spark plug
wires to the coils.
189. Use a 10mm deep socket to remove the four stock
coil cover ball studs from the valve covers.
183. Route the other end of the PCV hose to the tube
extending from the valley plate and attach it.
184. Install the supplied fuel line from the firewall fitting to
the U-shaped fitting on the driver side fuel rail.
190. Remove the grommets from the stock coil covers.
185. Connect fuel injector electrical connectors.
186. Use a small flathead screwdriver to remove the wire
covers at the back of the coil brackets. Note that you will
need to separate the covers from the bracket, then split the
two halves of the cover.
191. Install the stock grommets into the coil cover brackets
supplied in Bag #6.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 28
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
192. Use a 10mm socket to remove the bolts securing the
#2, #3, #6 and #7 ignition coils.
197. Remove the upper radiator hose to install the
serpentine belt.
193. Install the coil cover brackets on top of the ignition
coils, then use a 10mm socket to secure them with the
stock bolts. 198. Route the serpentine belt according to the diagram.
Note that you must slide the belt around the bottom of the
bracket to get the belt on the lower passenger side idler
pulley.
194. Tuck the wire harness tight against the fuel rails.
Verify nothing will be pinched or damaged when the coil
covers are installed.
195. Use a 7/16” deep socket to install the four ball studs
supplied in Bag #6 onto the supplied coil covers.
196. Plug the OEM engine harness MAP sensor connector
into the supplied MAP harness then route the harness to the
vicinity of the air intake.
199. Use a breaker bar and a 16mm socket to push the
tensioner enough to get the belt on, then double check the
routing.
200. Line up the tee fitting on the end of the oil cooler
outlet hose with the upper radiator hose. Cut the radiator
hose at the base of the barb on each side and discard the
section in between.
201. Attach the radiator hose sections to both sides of the
tee and secure them with hose clamps. Attach the hose to
the radiator and secure it with a clamp.
202. Use a 10mm socket and the two stock bolts to
reinstall the radiator fan.
203. Attach the radiator fan electrical connector then push
the stock hoses back into the factory clips.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 29
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
204. Use a 10mm socket, an extension bar, the four stock
bolts and the OEM O-ring seal to install the throttle body.
Torque the bolts to 91 in-lbs.
208. Install the grommet supplied in Bag #5 into the new
air inlet tube.
209. Install the hose barb supplied in Bag #5 into the new
air inlet tube.
205. Connect ETC harness to the throttle body motor.
210. Lower supplied air filter onto the radiator shroud.
206. Connect the intercooler hose assembly to the two
upper hose fittings at the front of the manifold.
211. Use a T15 Anti-Tamper Torx driver to remove the MAF
sensor from the stock airbox.
212. Use a 3/32” Allen tool and bolts supplied in Bag #5 to
install the supplied MAF sensor in the new inlet tube.
207. Install the silicone inlet tube to the throttle body and
secure it with a supplied worm clamp.
213. Route the supplied MAF wire harness near the driver
side of the throttle body.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 30
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
214. Install the two supplied grommets into the ears of
the new air inlet tube on cars equipped with locating pins.
219. Use a 10mm socket to reconnect the positive battery
terminal.
220. Use a 10mm socket to reconnect the negative battery
terminal.
221. Remove intercooler reservoir cap and fill intercooler
system with a 50/50 blend of water and coolant.
222. Refill the power steering reservoir with power
steering fluid. Check engine oil and coolant levels and top
them off, if needed.
215. Slide the nose of the air inlet tube into the air filter
then hold the grommets in place with a socket as you tilt
the air inlet tube down into the silicone tube and onto the
locator pins, if so equipped.
216. Connect the passenger side PCV hose to the air inlet
tube fitting, then route the hose along the passenger side
valve cover and connect it to the front fitting of the dry
sump tank . Connect the MAF harness to the MAF sensor
then connect the OEM MAF connector to the supplied MAF
harness.
217. Rotate the worm clamps so that the gears are on the
driver side then secure the air inlet tube by tightening the
worm clamps on the air filter and the silicone hose.
218. Use a 5/8” wrench to install the coil cover stands
supplied in Bag #6 onto the valve covers.
223. Turn the vehicle to the ‘ON’ position but DO NOT
START THE VEHICLE . (This is done by pressing the start
button without depressing the brake or clutch pedal).
224. Carefully inspect the fuel rail, fuel hose fittings and
coolant hoses for any leaks. If any leaks are detected, shut
the engine off immediately and make any necessary repairs
before continuing.
225. With the ignition in the “ON” position, verify that the
coolant mixture is flowing briskly through the recovery
tank, then install the cap. The intercooler pump will cycle
and the water level may change. Repeat step 221 as
necessary until proper mixture level is reached. Turn the
vehicle off once complete.
226. Reinstall the front fascia and reconnect the fog lamp
and indicator light electrical connectors.
227. Secure the front fascia with the stock hardware,
including the four bolts under the hood, the two nuts on
each fender, the five bolts and two nuts on the underside
and the four body pins that clip into the radiator shroud.
Refer to steps #5 - #11 for fastener locations.
228. Reattach the front valances using the three stock
screws and one body pin on each side.
229. Secure the front inner fender wells with the stock
fasteners.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 31
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
230. Reinstall the front wheels and torque the lug nuts in
a crossing pattern to 100 ft-lbs.
239. Use directional pad to highlight your vehicle and
transmission combination then press Select, again.
If you have yet to flash your ECU, then proceed with
steps 231-244, otherwise disregard them.
240. Use directional pad to highlight Begin Program then
press Select.
231. It is recommended that you check the Edelbrock
website (http://www.edelbrock.com/automotive_new/mc/
superchargers/fuel_injected_soft-tech.shtml) to confirm
that you have the latest calibration. Once you have found
the latest tune on the site, power on the programmer, press
the left arrow and select the Device Info option. Scroll down
to Tune Version and compare that number to the one on the
site. If they are different, download the new calibration with
the supplied USB cable.
241. Vehicles equipped with a manual transmission will
have three separate operations take place during this step,
while vehicles with an automatic transmission will have
five. Completion of each operation will cause the progress
bar to reset to zero.
DO NOT unplug the programmer until prompted.
232. Put the car into Acc mode by pressing and holding
the start button on the steering column. But don’t start the
vehicle.
233. Connect the supplied PCM cable to the OBDII connector located below the steering wheel in the
passenger compartment.
234. Use directional pad to highlight Program Vehicle
option and press Select button.
235. Use directional pad to highlight Pre-programmed
Tune option and press Select button.
242. Turn the car off when prompted to do so by the
handheld programmer.
243. Read parting message from programmer then press
Select to continue.
244. Unplug the programmer cable from the OBD-II port.
245. Start the car and allow it to idle while closely
inspecting the engine bay for any fuel or coolant leaks.
236. Read disclaimer then press Select to continue.
Repair any leaks before operating vehicle!
237. Verify ignition is in the ‘Key On’ position but that the
engine is not running then press Select.
246. Install the coil covers by sliding it into place and
pressing the ball studs into bracket grommets.
238. Use directional pad to highlight your vehicle and
transmission combination then press Select.
Congratulations on the installation of your new Edelbrock
E-Force Supercharger System. If you have any questions,
please call our Technical Support hotline and one of our
technicians will be happy to assist you.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 32
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Edelbrock GM LS7 Supercharger System for
2006 - 2010 Z06 Corvettes
Installation Instructions
Email Edelbrock Your Stock Vehicle Calibration
In the rare occurrence that you encounter an error message that reads “Calibration not supported” during
the test flash procedure on page 9, you will need to email Edlecbrock your stock vehicle calibration to
Calibration@edelbrock.com. Otherwise, disregard this step.
• Begin by downloading the SCT device updater software to your computer; it can be downloaded from: http://www.
sctflash.com/software/SCTDeviceUpdater.exe • Put the car into Acc mode but do not start it. • Connect the supplied PCM cable from the tuner to the OBD-II connector. • Select PROGRAM VEHICLE, arrow over to UPLOAD STOCK, press SELECT and follow the prompts on the
screen. • If the upload fails, you will be asked to AUTO DETECT, press SELECT and follow the prompts on the sceen. If the auto
detect fail, then please contact Edelbrock Tech support @ 800-416-8628
• Once the stock calibration has loaded, disconnect the programmer from the OBD-II connector and connect it to your PC
using the supplied USB cable. • Open the SCT software and select the button on the lower left hand side that reads GET STOCK FILE FROM DEVICE.
Follow the instructions on the screen. • Once the download is complete E-mail your calibration to Edelbrock at calibration@edelbrock.com or call 1-800-4168628 and our tech support staff will assist you in E-mailing the file. NOTE: The subject line of your e-mail should be “file
update needed”, The file will automatically be labeled using your VIN # followed by “.sul “ (XXXXXXXXXXXXX.sul)
• Once we have this file we can update the tune to work with your application, then we will e- mail you the custom tune
which you may use until the release version is available. (This process can usually be completed within 1 to 2 business
days)
• Download the new tune to the programmer using the directions received with the custom tune.
• Re-try the test flash procedure using the custom tune.
©2012 Edelbrock LLC
Part #1572 & 1573
Page 33
Brochure #63-1572
Rev. 11/06/12 - QT/mc
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising