Guardian GRD501-AR Adapter Matrix

Guardian GRD501-AR Adapter Matrix
An ISO 9001:2008 Registered Company
Guardian GRD501-AR
Adapter Matrix
Note:
Based on vehicle age and transmission code, it may be necessary to use one
of the adapters listed below along with the GRD501 or GRD502 part number.
Adapter
GRDP1
Application
Ford Econoline – 2005-2006 Transmission Code A, F, or Q
Ford Econoline – 2004 w/Gasoline or CNG Engines Only
GRDP2
Ford Econoline – 2003 Gas Engine with Transmission Code E or 9 only
GRDP3
Ford Econoline – 2003 Gas Engine with Transmission Code U only
GRDP4
Ford Econoline – 2003 Diesel Engine All Transmission Codes
GRDP5
Ford Econoline – 2003 Ford 5.4L CNG Engine All Transmission Codes
GRDP6
Ford Econoline – 1997-2002 Gas Engine with Transmission Code E or 9 only
GRDP7
Ford Econoline – 1997-2002 Gas Engine with Transmission Code U only
GRDP8
Ford Econoline – 1997-2002 Diesel Engine All Transmission Codes
GRDP9
Ford Econoline – 1997-2002 Ford 5.4L CNG Engine All Transmission Codes
GRDP10
Ford Econoline – 2007-2008 Gas Engine with Transmission Code Q only
Intermotive Inc.
13395 New Airport Rd. Ste A
Auburn,CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
www.intermotive.net
products@intermotive.net
Guardian501AR-01
An ISO 9001:2008 Registered Company
Guardian Personal Mobility Lift Interlock
GRD501-AR
1997-2008 Select Ford E-Series
Installation Instructions
GUARDIAN MODULE - Remove the lower dash panel below the steering column. The
Guardian Module should be positioned behind the metal knee bolster bracket below the steering
column. It can be secured using self tapping screws, adhesive foam tape, or wire ties. Do not
secure the module until all harnesses are installed and proper lift operation has been verified.
LED DISPLAY PANEL – This harness can be identified by the blue tape
near the 6-pin connector. Locate a suitable position on the dashboard, within
view of the driver for the mounting of the LED Display Panel. The length of
the display harness is 40”. This is the maximum distance the display can be
from the Guardian module. Drill a ¾” hole in the dashboard where you wish
the center of the display to be. Snap the blue taped end of the LED display
harness into the Guardian Module in the connector labeled in blue “Display”.
Run the other end of the harness under the dash and out through the ¾” hole. Snap the end of the
display harness into the LED Display Panel. Ensure panel is level, and secure using the supplied
screws.
LIFT HARNESS – This harness can be identified by the green tape near the
6-pin connector. Attach the appropriate wheelchair lift adapter to the lift
harness, then attach adapter to the wheelchair lift. Run the lift harness from
the wheelchair lift to the Guardian Module. Finally, snap the green taped
end of the Lift Harness into the Guardian connector labeled in green “Lift”.
Before continuing installation, the following check must be performed:
Intermotive Inc.
13395 New Airport Rd. Ste A
Auburn,CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
www.intermotive.net
products@intermotive.net
Guardian501AR-01
Verify that the vehicle ignition is off and the lift is fully stowed for at least 5 minutes. This will
ensure the Guardian module is in sleep mode. Attempt to deploy the wheelchair lift. Both the
red and green indicators on the LED Display Panel should briefly illuminate as a prove-out after
the module wakes up. If they do not, check to make sure each harness is connected to the proper
Guardian Module connector as outlined in the above steps. Only proceed to the next step if the
indicators illuminate. Otherwise, damage can occur to the module.
VEHICLE 1 HARNESS
This harness can be identified by the orange tape near the 6-pin connector. Disconnect the black
Ford connector from the Parking Brake. Plug the female side of the connector from the Brown
wire on the Vehicle 1 harness to the parking brake. Install the male side of the connector to the
female connector in the Ford harness.
2005-2008 Econoline with B or T Transmission Code only
Locate the Ford OEM Blunt cut wire for “Park”. This wire is located under the hood in the cowl
area. On gas engines, it is a White/Orange wire labeled “Park Out”. On diesel engines, it is a
Yellow/White wire labeled “TRO_P”. Verify that this wire provides ground in Park only. The
orange wire from the Vehicle 1 harness will be run through the vehicle bulkhead. Drill a 5/8”
hole in the bulkhead. Feed the orange wire into the engine compartment. Secure the grommet
on this wire in the drilled hole. The grommet can be moved along the harness for a custom fit.
Trim wire to proper length and connect to the Ford OEM Blunt cut wire for “Park” by soldering
the wires and sealing the connection with heat shrink tubing. Secure the harness with wire ties.
2005-2008 Econoline with A, F, or Q Transmission Code or 2004 Econoline with Gasoline
or CNG Engine only
These applications will not have a Ford OEM Blunt cut wire
for “Park”. An auxiliary Park Harness (Part # GRDP1 for
2004-2006) or (Part # GRDP10 for 2007-2008) will be
needed and the Vehicle 1 Harness will need to be modified.
Cut the Orange wire near the connector. Save the grommet,
and discard the Orange wire. Locate the Ford black 16-pin
(2004-2006) or black 10–pin (2007-2008) connector located
above the transmission bell housing. Separate the connector
halves and connect the black “T” harness connectors from
the optional Park Harness between them. Drill a 5/8” hole
in the bulkhead flange for the engine cover (see picture).
Feed the two green wires through the hole from the engine compartment. Slide the saved
grommet onto the harness and secure in the hole. The grommet can be moved along the harness
for a custom fit. Install the two Green wire terminals into the Vehicle 1 Harness connector in the
two empty slots next to where the orange wire was. Either Green wire can
be installed in either slot. Ensure that the metal pins securely lock into the 6pin connector. Secure the harness with wire ties
Snap the Vehicle 1 Harness into the Guardian Module connector labeled in
orange “Vehicle 1”.
Intermotive Inc.
13395 New Airport Rd. Ste A
Auburn,CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
www.intermotive.net
products@intermotive.net
Guardian501AR-01
VEHICLE 2 HARNESS - Locate the Ford shift lock solenoid on the steering column and
disconnect the black 3-pin connector. Be careful not to break the plastic tab on the connector.
Insert the black female 3-pin connector from the Vehicle 2 harness into the shift lock solenoid.
Ensure that it is fully seated into the solenoid. Insert the black male 3-pin connector from the
Vehicle 2 harness into the connector that was originally installed in the shift lock solenoid. It is
imperative that these connectors mate with the tabs on the same side. Use the supplied
small wire tie to secure the two tabs together. These connectors must
not be allowed to separate!
Snap the Vehicle 2 Harness into the Guardian Module connector labeled in
white “Vehicle 2”
Secure the Guardian Module in its final location and test for proper operation. (See Post
Installation Check List).
Intermotive Inc.
13395 New Airport Rd. Ste A
Auburn,CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
www.intermotive.net
products@intermotive.net
Guardian501AR-01
An ISO 9001:2008 Registered Company
Guardian Personal Mobility Lift Interlock
GRD501-AR/601-AR
Post Installation Check List
The following checks must be made after installation of the InterMotive Guardian GRD501
or GRD601 to ensure correct and safe operation of the lift. If any of the checks do not pass,
do not deliver the vehicle. Recheck all connections as per the installation instructions.
Begin the checklist with the vehicle in the following state:
• Lift stowed
• Park brake set
• Transmission in park
• Ignition off
• All Guardian LED’s not illuminated (sleep mode)
• Lift access door open
1.
Turn on the ignition. Verify that all LED’s prove out and green lift power LED remains
illuminated.
2.
Release the park brake. The green LED for lift power should now be off. Attempt to
deploy the lift. The lift must not deploy.
3.
Set the park brake and shift the transmission out of park. The green LED for lift power
should now be off. Attempt to deploy the lift. The lift must not deploy.
4.
Place the transmission in park. The green LED for lift power should now be illuminated.
5.
Attempt to deploy the lift. The lift should deploy and the red LED for lift-not-stowed
should illuminate.
6.
With the lift deployed, attempt to shift the transmission out of park. The transmission
shift lever must not be able to shift.
7.
Stow the lift. The red LED for lift-not-stowed should now be off.
8.
Turn off ignition.
9.
Wait approximately 5 minutes for the module to enter “sleep mode.” This is verified
when all LED’s (including backlit icons) turn off.
10.
Attempt to deploy the lift. The module should prove-out all LED’s and the lift should
deploy.
11.
Stow the lift. Installation is complete.
Intermotive Inc.
13395 New Airport Rd. Ste A
Auburn,CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
www.intermotive.net
products@intermotive.net
Guardian501AR-01
An ISO 9001:2008 Registered Company
Guardian Personal Mobility Lift Interlock
GRD501-AR/601-AR
Operating Instructions
The Guardian is a microprocessor driven system for controlling wheelchair lift operation. Lift
operation will only be allowed when all of the following conditions are met:
1. The vehicle is in “Park”
2. The parking brake is applied.
3. The lift deploy switch is activated
The Guardian also will not allow the vehicle to be shifted out of park if the lift is not stowed.
The Guardian will operate with the vehicle ignition on or off. When the ignition is turned on or
the lift deploy switch is activated, the LED panel will prove out by illuminating the red and green
indicators briefly. When the wheelchair lift is stowed and ignition power is not present for 5
minutes, the Guardian will enter a low current “sleep” mode of operation. To wake up from
“sleep” mode, the ignition must be turned on or the lift deploy switch must be activated. After
prove out, the operation of the indicators is as follows:
1
Lift Power – Illuminates in green if power is available to the lift. This means that all
conditions for lift operation have been met.
1
Lift Not Stowed – Illuminates in red when the wheelchair lift is not stowed. If illuminated,
the driver will not be allowed to shift out of park.
The indicators can also be used for diagnostic purposes. For example, if the Lift Not Stowed
icon is illuminated when the lift is stowed, the driver will not be able to shift out of park. This
means that the Guardian detects that the lift is not stowed. Thus, a technician should inspect the
lift stowed switch and its circuit for proper operation.
Intermotive Inc.
13395 New Airport Rd. Ste A
Auburn,CA 95602
Phone: (530) 823-1048
Fax: (530) 823-1516
www.intermotive.net
products@intermotive.net
Guardian501AR-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising