DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19

DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19
DPI C13 PDU+, DPI C13 3-phase PDU+,
DPI C19 PDU+, and DPI C19 3-phase PDU+
Installation and Maintenance Guide
DPI C13 PDU+, DPI C13 3-phase PDU+,
DPI C19 PDU+, and DPI C19 3-phase PDU+
Installation and Maintenance Guide
Note: Before using this information and the product it supports, read the warranty information in Appendix B, “IBM Statement of
Limited Warranty Z125-4753-08 04/2004,” on page 57 and the notices information in Appendix C, “Notices,” on page 75.
Third Edition (November 2007)
© Copyright International Business Machines Corporation 2006, 2007. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
Safety
. . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Chapter 1. Introduction . . . . . . .
The IBM Documentation CD . . . . .
Hardware and software requirements .
Using the Documentation Browser . .
Notices and statements in this document .
Installation requirements . . . . . . .
Parts that come with the PDU . . . . .
Features of the PDU . . . . . . . .
Hardware components . . . . . . .
Front view . . . . . . . . . . .
Rear view . . . . . . . . . . .
PDU load groups . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
1
1
2
3
3
4
5
6
6
8
8
Chapter 2. Installing the PDU vertically in a rack cabinet . . . . . . . . 11
Installing the PDU in the side of a rack cabinet . . . . . . . . . . . . . 12
Installing the PDU in the side of an IBM Enterprise rack cabinet only . . . . . 15
Chapter 3. Installing the PDU horizontally in a rack cabinet . . . . . . . 19
Chapter 4. Cabling the PDU . . . .
Connecting the console . . . . . . .
Connecting to a LAN . . . . . . . .
Connecting output devices . . . . .
Connecting an environmental monitoring
. .
. .
. .
. .
probe
Chapter 5. Monitoring the power status .
Using the IBM DPI Configuration Utility . .
Using HyperTerminal . . . . . . . .
Configuration Utility menu choices . . .
Setting the IP address . . . . . . .
Using the Web interface . . . . . . .
Starting the Web interface . . . . . .
Environment status and configuration .
Modifying the basic settings . . . . .
Changing the network information . . .
History and event log summaries . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
25
25
25
26
26
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
27
27
27
31
32
33
33
34
36
42
43
Chapter 6. Using the environmental monitoring probe . . . . . . . . . 45
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Installing the environmental monitoring probe . . . . . . . . . . . . . . 46
Chapter 7. Customer replaceable unit parts . . . . . . . . . . . . . 49
Chapter 8. PDU specifications
. . . . . . . . . . . . . . . . . . 51
Appendix A. Getting help and technical assistance
Before you call . . . . . . . . . . . . . . .
Using the documentation . . . . . . . . . . .
Getting help and information from the World Wide Web
Software service and support . . . . . . . . .
Hardware service and support . . . . . . . . .
© Copyright IBM Corp. 2006, 2007
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
55
55
55
55
56
56
iii
IBM Taiwan product service . . . . . . . . . . . . . . . . . . . . 56
Appendix B. IBM Statement of Limited
Part 1 - General Terms . . . . . . .
Part 2 - Country-unique Terms . . . .
Part 3 - Warranty Information . . . .
Warranty
. . . .
. . . .
. . . .
Z125-4753-08 04/2004
57
. . . . . . . . . . . 57
. . . . . . . . . . . 60
. . . . . . . . . . . 72
Appendix C. Notices . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . .
Important notes . . . . . . . . . . . . . . . . . .
Product recycling and disposal . . . . . . . . . . . .
Battery return program . . . . . . . . . . . . . . .
Electronic emission notices . . . . . . . . . . . . .
Federal Communications Commission (FCC) statement . .
Industry Canada Class A emission compliance statement .
Avis de conformité à la réglementation d’Industrie Canada .
Australia and New Zealand Class A statement . . . . .
United Kingdom telecommunications safety requirement . .
European Union EMC Directive conformance statement . .
Taiwanese Class A warning statement . . . . . . . .
Chinese Class A warning statement . . . . . . . . .
Japanese Voluntary Control Council for Interference (VCCI)
Korean Class A warning statement . . . . . . . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
statement
. . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
75
75
76
77
78
80
80
80
80
80
80
80
81
81
81
82
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
iv
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
© Copyright IBM Corp. 2006, 2007
v
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Important:
All caution and danger statements in this documentation end with a number. This
number is used to cross reference an English caution or danger statement with
translated versions of the caution or danger statement in the IBM Systems Safety
Notices document.
For example, if a caution statement ends with a number D005, translations for that
caution statement appear in the IBM Systems Safety Notices document under
D005.
Be sure to read all caution and danger statements in this documentation before
performing the instructions. Read any additional safety information that comes with
your server or optional device before you install the device.
DANGER
Overloading a branch circuit is potentially a fire hazard and a shock hazard
under certain conditions. To avoid these hazards, ensure that your system
electrical requirements do not exceed branch circuit protection
requirements. Refer to the information that is provided with your device or
the power rating label for electrical specifications. (D002)
DANGER
Hazardous voltage, current, or energy levels are present inside any
component that has this label attached. Do not open any cover or barrier
that contains this label.
(L001)
vi
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
DANGER
Electrical voltage and current from power, telephone, and communication
cables are hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet. Ensure outlet supplies proper voltage and phase rotation
according to the system rating plate.
v Connect any equipment that will be attached to this product to properly
wired outlets.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described below when installing,
moving, or opening covers on this product or attached devices.
To Disconnect:
1.
2.
3.
4.
To
1.
2.
3.
4.
5.
Turn everything OFF (unless instructed otherwise).
Remove power cords from the outlet.
Remove the signal cables from connectors.
Remove all cables from devices.
Connect:
Turn everything OFF (unless instructed otherwise).
Attach all cables to devices.
Attach signal cables to connectors.
Attach the power cords to outlets.
Turn device ON.
(D005)
Safety
vii
The following general safety information should be used for all rack-mounted
devices:
DANGER
v Always lower the leveling pads on the rack cabinet.
v Always install stabilizer brackets on the rack cabinet.
v To avoid hazardous conditions due to uneven mechanical loading,
always install the heaviest devices in the bottom of the rack cabinet.
Always install servers and optional devices starting from the bottom of
the rack cabinet.
v Rack-mounted devices are not to be used as a shelf or work space. Do
not place any object on top of rack-mounted devices.
v Each rack cabinet might have more than one power cord. Be sure to
disconnect all power cords in the rack cabinet before servicing any
device in the rack cabinet.
v Connect all devices installed in a rack cabinet to power devices installed
in the same rack cabinet. Do not plug a power cord from a device
installed in one rack cabinet into a power device installed in a different
rack cabinet.
v An electrical outlet that is not correctly wired could place hazardous
voltage on the metal parts of the system or the devices that attach to the
system. It is the responsibility of the customer to ensure that the outlet
is correctly wired and grounded to prevent an electrical shock.
CAUTION:
v Do not install a unit in a rack where the internal rack ambient temperatures
will exceed the manufacturer’s recommended ambient temperature for all
your rack-mounted devices.
v Do not install a unit in a rack where the air flow is compromised. Ensure
that air flow is not blocked or reduced on any side, front, or back of a unit
used for air flow through the unit.
v Consideration should be given to the connection of the equipment to the
supply circuit so that overloading of the circuits does not compromise the
supply wiring or overcurrent protection. To provide the correct power
connection to a rack, refer to the rating labels located on the equipment in
the rack to determine the total power requirement of the supply circuit.
v (For sliding drawers.) Do not pull out or install any drawer or feature if the
rack stabilizer brackets are not attached to the rack. Do not pull out more
than one drawer at a time. The rack may become unstable if you pull out
more than one drawer at a time.
v (For fixed drawers.) This drawer is a fixed drawer and must not be moved
for servicing unless specified by manufacturer. Attempting to move the
drawer partially or completely out of the rack may cause the rack to
become unstable or cause the drawer to fall out of the rack.
(R001)
viii
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 1. Introduction
The IBM® power distribution unit plus (PDU+) products have power monitoring
capabilities. These PDU+ products enable you to connect up to nine or 12
(depending on the PDU model) servers or rack PDUs to a single dedicated power
source. The following single-phase and three-phase PDUs are available:
v IBM DPI® C13 PDU+ (IBM part number 39M2816)
v IBM DPI C13 3-phase PDU+ (IBM part number 39M2817)
v IBM DPI C19 PDU+ (IBM part number 39M2818)
v IBM DPI C19 3-phase PDU+ (IBM part number 39M2819)
This release contains enhancements that enable the IBM Systems Director Active
Energy Manager product to monitor the IBM PDU+ products. The Active Energy
Manager solution is an IBM Director extension that measures and reports server
power consumption as it occurs. Active Energy Manager includes a feature to
associate IBM Director-managed resources with the power outlets on the PDU+.
You can use the graphing capability of Active Energy Manager to show a trending
line for power that is being drawn by load groups of the PDU+, showing which
systems are connected to the load groups.
If firmware and documentation updates are available, you can download them from
the IBM Web site. The PDU+ might have features that are not described in the
documentation that comes with the PDU+, and the documentation might be updated
occasionally to include information about those features, or technical updates might
be available to provide additional information that is not included in the PDU+
documentation. To check for updates, complete the following steps.
Note: Changes are made periodically to the IBM Web site. Procedures for locating
firmware and documentation might vary slightly from what is described in this
document.
1. Go to http://www.ibm.com/systems/support/.
2. Click Hardware upgrades.
3. On the “Support for IBM Upgrades” page, in the Product family field, select
Power.
4. In the Type field, select Distributed power interconnect (DPI).
5. In the Part number field, select your PDU+ part number.
6. Click Go.
7. On the “Support for Power” page, click Downloads for firmware updates, or
click Install/use for documentation updates.
The IBM Documentation CD
The IBM Documentation CD contains documentation for the PDU in Portable
Document Format (PDF) and includes the IBM Documentation Browser to help you
find information quickly.
Hardware and software requirements
The IBM Documentation CD requires the following minimum hardware and
software:
v Microsoft Windows XP, Windows 2000, or Red Hat Linux
v 100 MHz microprocessor
© Copyright IBM Corp. 2006, 2007
1
v 32 MB of RAM
v Adobe Acrobat Reader 3.0 (or later) or xpdf, which comes with Linux operating
systems
Using the Documentation Browser
Use the Documentation Browser to browse the contents of the CD, read brief
descriptions of the documents, and view documents, using Adobe Acrobat Reader
or xpdf. The Documentation Browser automatically detects the regional settings in
your computer and displays the documents in the language for that region (if
available). If a document is not available in the language for that region, the
English-language version is displayed.
Use one of the following procedures to start the Documentation Browser:
v If Autostart is enabled, insert the CD into the CD or DVD drive. The
Documentation Browser starts automatically.
v If Autostart is disabled or is not enabled for all users, use one of the following
procedures:
– If you are using a Windows operating system, insert the CD into the CD or
DVD drive and click Start --> Run. In the Open field, type
e:\win32.bat
where e is the drive letter of the CD or DVD drive, and click OK.
– If you are using Red Hat Linux, insert the CD into the CD or DVD drive; then,
run the following command from the /mnt/cdrom directory:
sh runlinux.sh
Select the PDU from the Product menu. The Available Topics list displays all the
documents for the PDU. Some documents might be in folders. A plus sign (+)
indicates each folder or document that has additional documents under it. Click the
plus sign to display the additional documents.
When you select a document, a description of the document is displayed under
Topic Description. To select more than one document, press and hold the Ctrl key
while you select the documents. Click View Book to view the selected document or
documents in Acrobat Reader or xpdf. If you selected more than one document, all
the selected documents are opened in Acrobat Reader or xpdf.
To search all the documents, type a word or word string in the Search field and
click Search. The documents in which the word or word string appears are listed in
order of the most occurrences. Click a document to view it, and press Crtl+F to use
the Acrobat search function, or press Alt+F to use the xpdf search function within
the document.
Click Help for detailed information about using the Documentation Browser.
2
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Notices and statements in this document
The caution and danger statements in this document are also in the multilingual
Systems Safety Notices document, which is on the IBM Documentation CD. Each
statement is numbered for reference to the corresponding statement in your
language in the Systems Safety Notices document.
The following notices and statements are used in this document:
v Note: These notices provide important tips, guidance, or advice.
v Important: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
v Attention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage might occur.
v Caution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
v Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
Installation requirements
You will need the following tools to install the PDU in a rack cabinet:
v One Phillips screwdriver
v One 10 mm (11/32 in.) wrench
v One cage-nut-insertion tool or flat-blade screwdriver (for installing cage nuts in
some rack cabinets)
You can install a PDU vertically in the side of a rack cabinet or horizontally within 1
U1 of EIA mounting space in a rack cabinet.
v For vertical mounting instructions, see Chapter 2, “Installing the PDU vertically in
a rack cabinet,” on page 11.
v For horizontal mounting instructions, see Chapter 3, “Installing the PDU
horizontally in a rack cabinet,” on page 19.
Attention: Horizontal installation of the PDU is not supported during relocation
or shipping of a rack cabinet. Before you relocate the rack cabinet, you must
remove any horizontally mounted PDU from the EIA mounting space.
1. One U is equal to 4.45 cm (1.75 in.)
Chapter 1. Introduction
3
Parts that come with the PDU
Note: The illustrations in this document might differ slightly from your hardware.
5
6
3
4
1
2
LAN
The following parts come with the PDU:
v One PDU (some models include detached power cords)
v Two vertical-mounting brackets (for all rack cabinets)
Note: This part does not come with the DPI C13 3-phase PDU+.
v Two short mounting brackets (for horizontal mounting for all rack cabinets; for
vertical mounting in IBM Enterprise rack cabinets only)
v Two long mounting brackets (for horizontal mounting in all rack cabinets)
Note: This part does not come with the DPI C13 3-phase PDU+.
4
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
v One cable-management bracket (for vertical installations)
Note: This part does not come with the DPI C13 3-phase PDU+.
v One DB9-to-RJ-45 cable
Note: This part does not come with the DPI C13 3-phase PDU+.
v One 1 U blank filler panel
Note: This part does not come with the DPI C13 3-phase PDU+.
v Miscellaneous hardware kit (for attaching the mounting brackets to the PDU and
installing the PDU in a rack cabinet)
Note: The DPI C13 3-phase PDU+ comes with four M3 flat-head screws, four
M6 flange-head screws, and four M6 clip nuts.
v Cable straps
Note: This part does not come with the DPI C13 3-phase PDU+.
Notes:
1. Power cables for devices that you will connect to the PDU do not come with the
PDU.
2. You will have some unused parts depending on how you install the PDU.
Features of the PDU
The PDU has the following features:
v Versatile sensors that are supported through environmental monitoring probe
inputs
v
v
v
v
v
v
v
v
Note: This feature requires the environmental monitoring probe, which comes
with the PDU+ models, except the DPI C13 3-phase PDU+. For the DPI C13
3-phase PDU+, you can order the environmental monitoring probe at the time of
purchase.
Remote monitoring of connected devices and sensors
Monitoring of the PDU manually, remotely through IBM Systems Director Active
Energy Manager, or remotely through a console or network
Comprehensive power management and flexible configuration through a Web
browser, NMS, Telnet, SNMP, or HyperTerminal (console)
Configurable user-security control
Easy-to-use interface to display input and output status
Detailed data-logging for statistical analysis and diagnostics
Upgrade utility for easy firmware updates
Event notification through SNMP trap or e-mail alerts
Chapter 1. Introduction
5
v Daily history report through e-mail
v Address-specific IP security masks to prevent unauthorized access
Hardware components
The following sections provide descriptions of the front and rear components on the
PDU.
Front view
The following illustration shows the components and controls on the front of the DPI
C13 PDU+ and the DPI C13 3-phase PDU+.
Note: The DPI C13 3-phase PDU+ comes with an attached power cord.
Reset button
RJ-45 LAN
connector
6
4
3
Operation
mode DIP switch
5
2
LED
1
LAN
RS-232 serial
connector
Circuit breakers
Input power
connector
Power outlets
RJ-45
console connector
The following illustration shows the components and controls on the front of the DPI
C19 PDU+ and the DPI C19 3-Phase PDU+.
Note: The DPI C19 3-Phase PDU+ comes with an attached power cord.
Reset button
RJ-45 LAN
connector
Circuit breakers
6
4
3
Operation
mode DIP switch
5
2
LED
1
LAN
RS-232 serial
connector
Power outlets
Input power
connector
RJ-45
console connector
RS-232 serial connector
Use the RS-232 serial connector to update the PDU firmware.
Reset button
Use this button to reset the PDU for communication purposes only.
Resetting the PDU does not affect the loads.
LED
The green LED shows the PDU input voltage status. When this LED is lit,
the PDU is receiving voltage. If the input voltage is too low, this LED is
flashing.
Circuit breakers
If the load current rating for a power outlet exceeds 20 A, the associated
circuit breaker is activated (the breaker pole pops out) and power to the
6
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
outlet is turned off automatically. To reset the circuit breaker, firmly press
the breaker pole until it locks into place.
Note: To manually disconnect power to a device that is connected to the
PDU, disconnect the device power cord from the PDU power outlet.
Input power connector
Connect a power cord to this connector.
Note: Some PDU models come with an attached power cord.
Power outlets
You can connect a device to each power outlet. There are either six or 12
power outlets on the front of the PDU, depending on the PDU model.
Note: There are three C13 power outlets on the rear of the DPI C19 PDU+
and the DPI C19 3-Phase PDU+ models.
Operation mode DIP switch
Use the switch to set the mode of operation for the PDU. The default mode
is S1 off, S2 off for normal operation.
1=Off, 2=Off
The PDU will run normal operational firmware.
1=On, 2=On
The PDU will start in diagnostics mode.
1=On, 2=Off
Serial upgrade mode. You can upgrade the PDU firmware from the
serial connection if the network upgrade is not available.
1=Off 2=On
Read-only mode. The device will run normal operational firmware,
but no parameters of the device can be changed by a user.
RJ-45 console connector
Connect the DB9-to-RJ-45 cable that comes with the PDU to this connector
and to the serial (COM) connector on a workstation or notebook computer,
and use the workstation or notebook computer as a configuration console.
You can also connect an environmental monitoring probe to this connector.
The environmental monitoring probe monitors humidity and temperature.
The connection of an environmental monitoring probe is automatically
detected.
Green LED (on the left in a horizontal orientation; on the top in a vertical
orientation):
v This LED is lit when the power to the PDU is turned on.
v This LED flashes while the PDU is starting to indicate startup status.
Amber LED (on the right in a horizontal orientation; on the bottom in a
vertical orientation):
v This LED flashes while the PDU is communicating with a server or
computer or when it is reading data from an environmental monitoring
probe.
Chapter 1. Introduction
7
RJ-45 Ethernet (LAN) connector
Use this connector to configure the PDU through a LAN. The Ethernet
connector supports 10/100 auto sense network connection.
Green LED (on the left):
v This LED is lit when the PDU is connected to a 100 Mb network.
v This LED flashes while data is transmitted and received.
Amber LED (on the right):
v This LED is lit when the PDU is connected to a 10 Mb network.
v This LED flashes while data is transmitted and received.
Rear view
The following illustration shows the rear of the DPI C13 PDU+ and the DPI C13
3-phase PDU+.
The following illustration shows the power outlets on the rear of the DPI C19 PDU+
and the DPI C19 3-Phase PDU+.
1A
3A
5A
C13
outlets
Labels indicating associated
breakers on the front of the PDU
PDU load groups
The PDU load groups are described in the following tables.
Table 1. DPI C13 PDU+ and DPI C13 3-phase PDU+ load groups
8
Circuit breaker number
Associated front outlets
1
1 and 2
2
3 and 4
3
5 and 6
4
7 and 8
5
9 and 10
6
11 and 12
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Table 2. DPI C19 PDU+ and DPI C19 3-phase PDU+ load groups
Circuit breaker number
Associated front outlet
Associated rear outlet
1
1
1A
2
2
3
3
4
4
5
5
6
6
3A
5A
Chapter 1. Introduction
9
10
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 2. Installing the PDU vertically in a rack cabinet
This chapter describes how to install the PDU vertically in a rack cabinet. To install
the PDU in the side of an IBM Enterprise rack cabinet, see “Installing the PDU in
the side of an IBM Enterprise rack cabinet only” on page 15.
DANGER
Electrical voltage and current from power, telephone, and communication
cables are hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet. Ensure outlet supplies proper voltage and phase rotation
according to the system rating plate.
v Connect any equipment that will be attached to this product to properly
wired outlets.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described below when installing,
moving, or opening covers on this product or attached devices.
To Disconnect:
1. Turn everything OFF (unless instructed otherwise).
2. Remove power cords from the outlet.
3. Remove the signal cables from connectors.
4. Remove all cables from devices.
To Connect:
1. Turn everything OFF (unless instructed otherwise).
2. Attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach the power cords to outlets.
5. Turn device ON.
(D005)
© Copyright IBM Corp. 2006, 2007
11
Installing the PDU in the side of a rack cabinet
The mounting holes on the upper and lower side braces in a rack side compartment
must be between 48.6 cm (19.1 in.) and 56.9 cm (22.4 in.) apart. If your rack
cabinet has movable side braces, see the rack cabinet documentation for
information about relocating the side braces if they are not already spaced for this
installation.
Note: Removing the rack doors and side panels might make installation easier.
See the rack cabinet documentation for more information.
Review the documentation that comes with your rack cabinet for safety and cabling
information. When you install the PDU in a rack cabinet, observe the following
precautions:
v Make sure that the room air temperature is below 35°C (95°F).
v Do not block any air vents; usually 15 cm (6 in.) of air space provides proper
airflow.
v Connect all power cords to properly wired and grounded electrical outlets.
v Do not overload the power outlet when you install multiple devices in the rack
cabinet.
5
6
3
4
1
2
LAN
To install a PDU in the side of a rack cabinet by using the vertical mounting
brackets, complete the following steps:
1. Align the vertical mounting brackets to the front of the PDU and attach the
brackets to the PDU with two M3 x 5 screws per bracket. Use the screws that
come with the PDU. You can install the PDU in a rack cabinet with the power
outlets facing the rear or the front of the rack cabinet.
12
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
2. Hold the PDU in the side of the rack cabinet, and attach the vertical mounting
brackets to the side braces with four M6 screws and nuts that come with the
PDU.
Notes:
a. Leave enough space to connect, route, and disconnect power cords.
b. If you are installing a cable-management bracket in the same side of the
rack cabinet, leave enough space between the outlet side of the PDU and
the EIA mounting flanges for the cable-management bracket installation.
Attention: You must disconnect the main input power before you connect or
disconnect the input power cord from the PDU.
3. If the PDU comes with a detached power cord, connect the power cord. Align
the connector on the power cord that comes with the PDU with the connector
on the front of the PDU, turning as necessary for key alignment; then, turn the
twist-lock on the connector clockwise until it locks into place.
Key alignment
Twist lock
Chapter 2. Installing the PDU vertically in a rack cabinet
13
4. Install the optional cable-management bracket beside the PDU with four M6
screws and nuts that come with the PDU.
5. Route the power cord from the PDU toward the rack cabinet side braces; then,
route the power cord along a side brace toward the back of the rack cabinet,
and secure the power cord with the cable straps that come with the PDU.
6. Route the power cord toward a dedicated power source. Use the provided cable
straps to secure the power cord along the way. If the power cord must exit the
rack cabinet to connect to a power source, use the openings in the rack cabinet.
7. Connect the power cord to a properly wired and grounded dedicated power
source. Then, you can connect servers or rack PDUs in the rack cabinet to the
power outlets on the PDU.
14
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
8. Route all the other power cords neatly, using the cable-management bracket if it
is installed, and secure the power cords with cable straps.
Note: To route a power cord through the cable-management bracket, route the
cord through an opening in the bracket and against an upper or lower tab on
the bracket, as shown in the following illustration. Use cable straps as required.
Tab
Installing the PDU in the side of an IBM Enterprise rack cabinet only
Note: Removing the rack doors and side panels might make installation easier.
See the rack cabinet documentation for more information.
Review the documentation that comes with your rack cabinet for safety and cabling
information. When you install the PDU in a rack cabinet, observe the following
precautions:
v Make sure that the room air temperature is below 35°C (95°F).
v Do not block any air vents; usually 15 cm (6 in.) of air space provides proper
airflow.
v Connect all power cords to properly wired and grounded electrical outlets.
v Do not overload the power outlet when you install multiple devices in the rack.
Chapter 2. Installing the PDU vertically in a rack cabinet
15
You must use clip nuts to install the mounting brackets. Clip nuts come with the
PDU and are installed on the rack mounting flanges, as shown in the following
illustration.
21
20
19
5
6
3
4
1
2
LAN
To install the PDU in the 1 U mounting space in the side of an IBM Enterprise rack
cabinet, complete the following steps:
1. Align the vertical-mounting brackets to the front of the PDU. Make sure that you
attach the brackets so that the power outlets face the rear of the rack cabinet.
2. Attach the brackets to the PDU with two M3 x 5 screws per bracket. Use the
screws that come with the PDU.
16
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
3. Align the PDU with the opening in the side of the rack cabinet; then, while you
hold the PDU in place, attach the brackets to the rack-mounting flanges with
four clip nuts and four M6 screws that come with the PDU.
LA
N
1
2
3
4
5
6
Attention: You must disconnect the main input power before you connect or
disconnect the input power cord from the PDU.
4. If the PDU comes with a detached power cord, connect the power cord. Align
the connector on the power cord that comes with the PDU with the connector
on the front of the PDU, turning as necessary for key alignment; then, turn the
twist-lock on the connector clockwise until it locks into place.
Key alignment
Twist lock
Chapter 2. Installing the PDU vertically in a rack cabinet
17
5. Route the power cord from the PDU toward the rack cabinet side braces; then,
route the power cord along a side brace toward the back of the rack cabinet,
and secure the power cord with the cable straps that come with the PDU.
6. Route the power cord toward a dedicated power source. Use the provided cable
straps to secure the power cord along the way. If the power cord must exit the
rack cabinet to connect to a power source, use the openings in the rack cabinet.
7. Connect the power cord to a properly wired and grounded dedicated power
source. Then, you can connect servers or rack PDUs in the rack cabinet to the
power outlets on the PDU.
8. Route all the other power cords neatly and secure the power cords with cable
straps.
18
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 3. Installing the PDU horizontally in a rack cabinet
Attention: Horizontal installation of a PDU is not supported during relocation or
shipping of a rack cabinet. You must remove any horizontally mounted PDUs from
the EIA mounting space before you relocate the rack cabinet.
Note: Removing the rack doors and side panels might make installation easier.
See the rack cabinet documentation for more information.
Review the documentation that comes with your rack cabinet for safety and cabling
information. When you install the PDU in a rack cabinet, observe the following
precautions:
v Make sure that the room air temperature is below 35°C (95°F).
v Do not block any air vents; usually 15 cm (6 in.) of air space provides proper
airflow.
v Plan the device installation starting from the bottom of the rack cabinet.
v Install the heaviest device in the bottom of the rack cabinet.
v Do not extend more than one device out of the rack cabinet at the same time.
v Connect all power cords to properly wired and grounded electrical outlets.
v Do not overload the power outlet when you install multiple devices in the rack
cabinet.
Use cage nuts for rack cabinets with square holes, and use clip nuts for rack
cabinets with round holes. If your rack cabinet requires cage nuts, use a
cage-nut-insertion tool or a flat-blade screwdriver to install them.
Cage
nuts
Cage
nuts
© Copyright IBM Corp. 2006, 2007
Clip
nuts
19
DANGER
Electrical voltage and current from power, telephone, and communication
cables are hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet. Ensure outlet supplies proper voltage and phase rotation
according to the system rating plate.
v Connect any equipment that will be attached to this product to properly
wired outlets.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described below when installing,
moving, or opening covers on this product or attached devices.
To Disconnect:
1.
2.
3.
4.
To
1.
2.
3.
4.
5.
Turn everything OFF (unless instructed otherwise).
Remove power cords from the outlet.
Remove the signal cables from connectors.
Remove all cables from devices.
Connect:
Turn everything OFF (unless instructed otherwise).
Attach all cables to devices.
Attach signal cables to connectors.
Attach the power cords to outlets.
Turn device ON.
(D005)
20
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
5
6
3
4
1
2
LAN
To install the PDU horizontally in a rack cabinet, complete the following steps:
1. Align the short mounting brackets with the holes in the front of the PDU and
attach the brackets to the PDU with two M3 flat-head screws per bracket. Use
the screws that come with the rack-mounting kit.
Short mounting bracket
2. Align the long mounting brackets with the holes in the rear of the PDU and
attach the brackets to the PDU with two M3 pan-head screws with captive lock
washers per bracket. Use the screws that come with the rack-mounting kit.
5
6
3
4
1
2
LAN
Long mounting bracket
3. Hold the PDU at a slight angle and carefully insert it into the 1 U mounting
space in the rack cabinet. Pushing in slightly on both of the long mounting
brackets helps clear the brackets from the rack flanges.
Chapter 3. Installing the PDU horizontally in a rack cabinet
21
5
6
3
4
1
2
LAN
4. Secure the end of the PDU that has the short mounting brackets to the rack
cabinet first. Make sure that the short mounting brackets are aligned with the
outside of the rack flanges. Attach the brackets to the rack flanges with two M6
screws and two cage nuts or clip nuts per bracket. Use the cage nuts or clip
nuts and the screws that come with the rack-mounting kit.
5. Secure the long mounting brackets and the 1 U blank filler panel to the rack
cabinet.
Blank filler panel
a. Adjust the long mounting brackets to fit the depth of the rack cabinet.
b. Make sure that the long mounting brackets are aligned with the inside of
the rack flanges.
22
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
c. Align the blank filler panel on the outside of the rack flanges.
d. Attach the filler panel to the rack flanges and then to the long mounting
bracket with one M6 screw per bracket.
e. Tighten the M3 pan-head screws that secure the long mounting brackets to
the PDU.
6. If the PDU comes with a detached power cord, connect the power cord. Align
the connector on the power cord that comes with the PDU with the connector
on the front of the PDU, turning as necessary for key alignment; then, turn the
twist-lock on the connector clockwise until it locks into place.
Key alignment
Twist lock
7. Route the power cord from the PDU toward the rack cabinet side braces; then,
route the power cord along a side brace toward the back of the rack cabinet,
and secure the power cord with the cable straps that come with the PDU.
8. Route the power cord toward a dedicated power source. Use the provided
cable straps to secure the power cord along the way. If the power cord must
exit the rack cabinet to connect to a power source, use the openings in the
rack cabinet.
9. Connect the power cord to a properly wired and grounded dedicated power
source. Then, you can connect servers or rack PDUs in the rack cabinet to the
power outlets on the PDU.
10. Route all the other power cords neatly and secure the power cords with cable
straps.
Chapter 3. Installing the PDU horizontally in a rack cabinet
23
24
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 4. Cabling the PDU
This chapter provides information about cabling the PDU, connecting power, and
connecting devices.
Connecting the console
Use the DB9-to-RJ-45 cable that comes with the PDU to connect the serial (COM)
connector on a workstation or notebook computer to the RJ-45 console connector
on the PDU, as shown in the following illustration.
DB9-to-RJ-45 cable
5
RJ-45
console
connector
6
3
4
1
2
LAN
PDU
Serial
connector
For more information, see “Using the IBM DPI Configuration Utility” on page 27.
Connecting to a LAN
You can monitor the PDU power outlets and digital outputs over a network through
the Web interface, using a LAN connection.
Connect a router or switch to the RJ-45 LAN connector on the PDU, using an
Ethernet cable. You can then monitor the PDU from a workstation or notebook
computer that is connected to the same network. For more information about how
to monitor the PDU and its output devices through the Web, see “Using the Web
interface” on page 33.
Ethernet cable
Router
© Copyright IBM Corp. 2006, 2007
5
RJ-45
LAN
connector
6
3
4
1
2
LAN
PDU
25
Connecting output devices
The PDU has nine or 12 power outlets for connecting devices such as workstations,
servers, and printers. You can monitor the power status of a connected device
either manually or remotely through the LAN and console connectors. Connect a
device that you want to monitor to a power outlet on the PDU with the power cord
that comes with the device.
Connecting an environmental monitoring probe
The environmental monitoring probe that comes with the PDU has a built-in
temperature and humidity sensor and enables you to remotely monitor the
temperature and humidity of the environment that the PDU is operating in. Connect
the environmental monitoring probe to the RJ-45 console connector on the PDU, as
shown in the following illustration.
Environmental
monitoring
probe
5
RJ-45
console
connector
6
3
4
1
2
LAN
RJ-45
connector
PDU
Ethernet cable
For more information about the environmental monitoring probe, see Chapter 6,
“Using the environmental monitoring probe,” on page 45.
26
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 5. Monitoring the power status
You can monitor the power status of any device that is connected to the PDU,
either manually or remotely, through the PDU Web interface. You can use the IBM
DPI Configuration Utility to initially set up the PDU and to configure PDU settings
such as network parameters, access control table, and trap receivers table. You can
also use IBM Systems Director Active Energy Manager to monitor power usage of
the PDU+ and its load groups.
Note: All of the Configuration Utility configuration menu choices are available
through the Web interface after the PDU is set up on the local network.
Using the IBM DPI Configuration Utility
This section describes how to use the IBM DPI Configuration Utility to configure the
PDU settings, such as the IP address, network parameters, access control table,
and trap receivers table.
You can configure the PDU by using a workstation or notebook computer that is
connected to the PDU. Connect the DB9-to-RJ-45 cable that comes with the PDU
to the RJ-45 console connector on the PDU and to a RS-232 serial (COM)
connector on a workstation or notebook computer. For more information, see
“Connecting the console” on page 25.
Using HyperTerminal
HyperTerminal is a terminal program in a Microsoft Windows operating system that
you can use to configure or control a device, using command line parameters. You
can configure the PDU parameters and its outlets, using numerical commands from
a keyboard. You can also use Telnet or any other terminal program to configure the
PDU after the IP address is set.
© Copyright IBM Corp. 2006, 2007
27
To start HyperTerminal and communicate with the PDU, complete the following
steps:
1. To start HyperTerminal, click Start → Programs → Accessories →
Communications → HyperTerminal. The Connection Description window
opens.
2. In the Name field, type the name for the connection and select an icon for the
connection. Click OK. The Connect To window opens.
28
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
3. From the Connect using list, select the COM port that is connected to the
PDU. Click OK. The Properties window opens.
4. Click Restore Defaults to use the default settings. Make sure that 9600 is
selected in the Bits per second list and that None is selected in the Flow
control list. Click OK.
Chapter 5. Monitoring the power status
29
5. Press any key. The IBM DPI Configuration Utility main menu opens, and you
are prompted for a password. Type passw0rd (all lowercase letters with a zero,
not O) and press Enter.
The IBM DPI Configuration Utility main window opens.
See “Configuration Utility menu choices” on page 31 for descriptions of the choices
in this window.
30
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Configuration Utility menu choices
The following choices are on the Configuration Utility main menu:
v IBM DPI Settings
When you select IBM DPI Settings, the following window opens.
The following choices are available:
– Set the IP Address, Gateway Address and MIB System Group
Select this choice to view and change the IP address, date, time, and MIB
system information.
– Set IBM DPI Control Group
–
–
–
–
–
–
Select this choice to set the administrator user name, password, and access
protocols.
Set Write Access Managers
Select this choice to set up a list of users who can access and control the
PDU.
Set Trap Receivers
Select this choice to configure remote network management system (NMS)
servers to receive traps.
SNMPv3 USM Table
Select this choice to set the SNMPv3 USM Table to configure the PDU using
SNMPv3 tools.
Set Date and Time
Select this choice to adjust the date and time information for the PDU.
Set Superuser Name and Password
Select this choice to set the user name and password of the administrator
who will use a Web browser to configure the PDU.
E-mail Notification
Select this choice to set up a list of users who will be alerted with event
messages if an unusual event is triggered on the PDU.
Chapter 5. Monitoring the power status
31
– Set Multi-Users
Select this choice to configure other user and password logins and the read
and write access levels.
– Set IBM DPI Information
Select this choice to configure the PDU logging interval, refresh rate, and
custom name fields for the load groups.
– Settings and Event Log Summary
Select this choice to view all PDU configuration settings.
v Reset Configuration to Default
Select this choice to reset all PDU settings to their factory default values.
v Restart HD-PDU
Select this choice to restart the PDU.
Setting the IP address
Note: You must set the IP address before you can use the Web interface.
To set the IP address of the PDU, in the Configuration Utility main menu, select
IBM DPI Settings and then select Set the IP Address, Gateway Address and
MIB System Group. You must set the IP address before you can access the PDU
in an IP network (LAN/WAN). Contact your system administrator if you do not know
the IP address.
32
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Using the Web interface
This section provides information about using the Web interface to configure and
monitor the PDU remotely. The PDU provides a graphical user interface that you
can view from a Web browser. Using a Web browser, you can access and monitor
the PDU power outlets and output devices remotely from a workstation or notebook
computer.
Starting the Web interface
To start the Web interface, complete the following steps:
1. Start a Web browser from a workstation or notebook computer and enter the IP
address of the PDU in the address field. For more information about setting the
IP address of the system, see “Setting the IP address” on page 32.
2. The “Connect to” window opens. In the User name field, type USERID (all
uppercase letters). In the Password field, type passw0rd (all lowercase letters
with a zero, not O).
3. Click OK. The main status page opens.
The main page shows a graphical representation of the PDU power outlets and
input status:
v The left pane shows the menus and submenus for the PDU. Click a menu to
display the menu choices, expand the menu items, and modify the menu
choices as required.
v The graphic in the right pane shows the status of the outlets, input voltage,
output voltage, frequency, current and power, watt-hour consumption, and
cumulative kilowatt hour power consumption. If you connect an optional
environmental monitoring probe, the temperature and humidity environment
conditions are displayed.
Each menu page provides online help to assist you with configuring the PDU.
Click the Help icon at the top of each page to view the help.
Chapter 5. Monitoring the power status
33
Environment status and configuration
If an environmental monitoring probe is connected to the PDU, you can view the
temperature and humidity information. For more information about installing and
using the environmental monitoring probe, see Chapter 6, “Using the environmental
monitoring probe,” on page 45.
Viewing the status
On the Status of Environment Sensor page, you can view the environment status
(temperature and humidity).
To view the status of an environmental monitoring probe that is connected to the
PDU, click Status under Environment. The Status of Environment Sensor page
opens, and the temperature and humidity of the environment sensor are displayed.
34
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Changing the configuration settings
On the Configuration of Environment Sensor page, you can change the system
configuration of the environment sensor.
To configure the environmental monitoring probe that is connected to the PDU, click
Configuration under Environment. You can set the sensor names, high and low
set points, and the calibration offsets of the sensors.
Chapter 5. Monitoring the power status
35
Modifying the basic settings
Use the System menu to configure the PDU system parameters such as the
superuser name, password, IP address, date, time, and so on. Some of these
settings are described in the following sections.
Changing the superuser name and password
On the Configuration page, you can set the user name and password of the
administrator who will use a Web browser to configure the PDU.
To change the superuser name and password, complete the following steps:
1. From the main status page, in the left navigation pane, click System.
2. Click Configuration to view and modify the system configuration and superuser
user name and password.
36
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Identifying the PDU and Web/SNMP card
On the Identification of Power Management page, you can view the PDU and
Web/SNMP card information.
To view the power management information of the PDU and Web/SNMP card,
complete the following steps:
1. From the main status page, in the left navigation pane, click System.
2. Click Identification to view the PDU and Web/SNMP card information.
Chapter 5. Monitoring the power status
37
Adding users
On the Multi-User Configuration page, you can add users who can access and
control the PDU.
To create a list of users who can access and control the PDU, complete the
following steps:
1. From the main status page, in the left navigation pane, click System.
2. Click Multi-User. You can add users who can only view the PDU status or
users who can change the PDU settings.
38
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Changing the date and time
On the Date and Time page, you can change the date and time of the PDU.
Note: Changing the PDU date and time affects other PDU settings such as e-mail,
traps, and logs.
To change the date and time, complete the following steps:
1. From the main status page, in the left navigation pane, click System.
2. Click Date and Time to view and modify the system date and time. You can set
the date and time manually, synchronize it with the computer time, or
synchronize it with an NTP server.
Chapter 5. Monitoring the power status
39
Changing event alerts
On the SNMP Trap Receivers page, you can change event alerts.
To configure the PDU to send e-mail or SNMP trap alerts to specified users when
specific events occur, complete the following steps:
1. From the main status page, in the left navigation pane, click System.
2. Click Trap Receivers to create a list of users or workstations who will be
alerted with an SNMP trap message. You can specify the IP addresses of up to
eight trap receivers, the community information, type of trap, severity of trap,
and description of the events that cause the traps.
40
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
3. Click Email Notification under System to create a list of up to four users who
will be alerted with an e-mail. Use this menu to specify the mail server, user
account, DNS, and other information that is necessary to set up a mail server
for sending mail alerts. Use the Email Receivers Table to add the e-mail
addresses.
Chapter 5. Monitoring the power status
41
Changing the network information
Use the Network menu to change the network information for the PDU, for example,
the IP address.
Changing the network configuration
To view or change the network configuration of the PDU, under Network, click
Configuration. You can set the PDU IP address, gateway address, subnet mask,
and Domain Name System (DNS) address.
Click Control under Network to configure TCP/IP settings.
Click Access Control under Network to set access control to prevent unauthorized
users from accessing the PDU.
Click SNMPv3 USM Table to configure SNMPv3 settings.
42
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
History and event log summaries
The Logs menu provides a detailed description of all events and a record of the
PDU status. System administrators can use this page to analyze problems with
network equipment.
Viewing the history log
On the History Log page, you can view the complete history of the PDU inputs,
outputs, and environmental monitoring probe.
To view the history of the PDU, under Logs, click History. Each log file shows a
record of the input power, output power of each outlet, and environmental
monitoring probe temperature and humidity.
Viewing the event log
On the Event Log page, you can view the complete record of the PDU events.
To view the complete record of the PDU events, under Logs, click Event. Each
event log file shows the time, date, and description of all the events that have
occurred on the PDU.
Chapter 5. Monitoring the power status
43
44
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 6. Using the environmental monitoring probe
Note: The environmental monitoring probe comes with the PDU+ models, except
the DPI C13 3-phase PDU+. For the DPI C13 3-phase PDU+, you can order the
environmental monitoring probe at the time of purchase.
The environmental monitoring probe is a connectivity device that enables you to
remotely monitor the temperature, humidity, and status of two contact devices
through a standard Web browser, providing greater power management control and
flexible monitoring.
You can use the environmental monitoring probe with any IBM DPI PDU+ models.
When the environmental monitoring probe is connected to the RJ-45 console
connector on the PDU, temperature and humidity readings are automatically
displayed in the Web interface. To access the readings, you must run the Web
browser and connect to the PDU IP address.
Evironmental
monitoring
probe
RJ-45
connector
Features
The environmental monitoring probe has the following features:
v The hot-swap feature simplifies installation by enabling you to install the probe
safely without turning off power to the PDU or to the loads that are connected to
it.
v It monitors temperature and humidity information of any environment that you
want to protect your critical equipment.
v It measures temperatures between 0 and 80°C (32 and 176°F) with an accuracy
of ±1°C.
v It measures relative humidity between 10 and 90% with an accuracy of ±5%.
v It can be located away from the PDU with a CAT5 network cable up to 20 m
(65.6 ft) long.
v It monitors the status of the two user-provided contact devices.
v Temperature, humidity, and contact closure status can be displayed through a
Web browser.
v User-selectable alarm thresholds enable you to define acceptable temperature or
humidity limits
v E-mail notification through Simple Mail Transfer Protocol (SMTP), using e-mail
client software when acceptable alarm limits are exceeded or contact status
changes.
© Copyright IBM Corp. 2006, 2007
45
v Changes in contact closure status are logged in the PDU event history log.
v When temperature and humidity values exceed user-selectable limits, the event
is logged in the PDU event history log.
Installing the environmental monitoring probe
To install the environmental monitoring probe, complete the following steps:
1. If applicable, connect external contact closure inputs to the screw terminals on
the environmental monitoring probe.
Pin 1
Environmental
monitoring
probe screw
terminals
Note: Contact closure device 1 is connected between pins 1 and 2. Device 2 is
connected between pins 3 and 4 (as labeled to show device 1 and 2). Contact
closure devices can be normally open or normally closed.
Table 3. Environmental monitoring probe screw terminal pin assignment
Pin number
Description
Normally open/
normally closed
1
Contact 1 return
Normally closed
2
Contact 1 signal input
Normally open
3
Contact 2 return
Normally closed
4
Contact 2 signal input
Normally open
2. Connect the CAT5 network cable that comes with the PDU to the environmental
monitoring probe RJ-45 connector and to the RJ-45 console connector on the
PDU.
Note: If the cable is not long enough for your configuration, you can use a
cable that is 20 m (65.6 ft) or less.
Environmental
monitoring
probe
5
RJ-45
console
connector
6
3
4
1
2
LAN
RJ-45
connector
PDU
Ethernet cable
3. Make sure that the PDU has a network connection, the power cord is
connected, and the power to the PDU is turned on. The environmental
monitoring probe is automatically recognized by the PDU.
46
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
4. Start a Web browser and connect to the PDU IP address (for more information,
see “Using the Web interface” on page 33). The Web interface main status page
opens. Click Environment, and then click Status. The Status of Environment
Sensor page opens. The temperature and humidity status is automatically
displayed.
Chapter 6. Using the environmental monitoring probe
47
5. Before the status of the contact closures is displayed, you must configure and
enable this feature on the PDU Web interface. Click Environment, and then
click Configuration. The Configuration of Environment Sensor page opens.
You can configure and enable both contacts and set upper and lower ranges of
temperature and humidity that will generate SNMP traps and e-mail notification
if the PDU is configured to do so.
48
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 7. Customer replaceable unit parts
Replaceable components are of three types:
v Tier 1 customer replaceable unit (CRU): Replacement of Tier 1 CRUs is your
responsibility. If IBM installs a Tier 1 CRU at your request, you will be charged for
the installation.
v Tier 2 customer replaceable unit: You may install a Tier 2 CRU yourself or
request IBM to install it, at no additional charge, under the type of warranty
service that is designated for your server.
v Field replaceable unit (FRU): FRUs must be installed only by trained service
technicians.
For information about the terms of the warranty and getting service and assistance,
see Appendix B, “IBM Statement of Limited Warranty Z125-4753-08 04/2004,” on
page 57.
Important: The PDU does not contain any serviceable parts.
PDU
Tier 1 CRU
part number
Power cord
Tier 1 CRU
part number
DPI 32 amp/250 V 1-phase Enterprise C13 PDU+
with IEC 309 2P+N+Gnd connector
40K9637
39M5428
DPI 60 amp/208 V 1-phase Enterprise C13 PDU+
with IEC 309 2P+Gnd connector
40K9637
39M5431
DPI 63 amp/250 V 1-phase Enterprise C13 PDU+
with IEC 309 2P+N+Gnd connector
40K9637
39M5429
DPI 32 amp/250 V 3-phase Enterprise C13 PDU+
with IEC 309 3P+N+Gnd connector
40K9637
39M5427
DPI 30 amp/208 V 1-phase Enterprise C13 PDU+
with Nema L6-30P connector
40K9637
39M5430
DPI 60 amp/208 V 3-phase Enterprise C13 PDU+
with IEC 309 3P+Gnd connector
43V5995
Cord comes
attached to PDU
DPI 60 amp/208 V 1-phase Enterprise C19 PDU+
with IEC 309 2P+Gnd connector
40K9638
39M5431
DPI 63 amp/250 V 1-phase Enterprise C19 PDU+
with IEC 309 2P+N+Gnd connector
40K9638
39M5429
DPI 32 amp/250 V 3-phase Enterprise C19 PDU+
with IEC 309 3P+N+Gnd connector
40K9638
39M5427
DPI 60 amp/208 V 3-phase Enterprise C19 PDU+
with IEC 309 3P+Gnd connector
40K9639
Cord comes
attached to PDU
Environmental monitoring probe kit
41Y9210
Mounting hardware kit
41Y9284
DB9-to-RJ-45 cable
40K9640
PDU description
© Copyright IBM Corp. 2006, 2007
49
50
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Chapter 8. PDU specifications
The following table contains the product specifications of the PDUs. The PDUs in
the following list correspond by number to the rated voltages, maximum power
ratings, and power cords that are listed in the table:
1. DPI 32 amp/250 V 1-phase Enterprise C13 PDU+ with IEC 309 2P+N+Gnd
connector
2. DPI 60 amp/208 V 1-phase Enterprise C13 PDU+ with IEC 309 2P+Gnd
connector
3. DPI 63 amp/250 V 1-phase Enterprise C13 PDU+ with IEC 309 2P+N+Gnd
connector
4. DPI 32 amp/250 V 3-phase Enterprise C13 PDU+ with IEC 309 3P+N+Gnd
connector
5. DPI 30 amp/208 V 1-phase Enterprise C13 PDU+ with Nema L6-30P
connector
6. DPI 60 amp/208 V 3-phase Enterprise C13 PDU+ with IEC 309 3P+Gnd
connector
7. DPI 60 amp/208 V 1-phase Enterprise C19 PDU+ with IEC 309 2P+Gnd
connector
8. DPI 63 amp/250 V 1-phase Enterprise C19 PDU+ with IEC 309 2P+N+Gnd
connector
9. DPI 32 amp/250 V 3-phase Enterprise C19 PDU+ with IEC 309 3P+N+Gnd
connector
10. DPI 60 amp/208 V 3-phase Enterprise C19 PDU+ with IEC 309 3P+Gnd
connector
Height
43.9 mm (1.73 in.)
Width
447 mm (17.6 in.)
Depth
350 mm (13.78 in.)
Additional clearance
25 mm (0.98 in.) for circuit breakers
3 mm (0.12 in.) for outlets
Weight (not including power cord)
6.3 kg (13.8 lb)
Weight of power cord (approximate,
varies by PDU model)
5.4 kg (11.8 lb)
Operating temperature at 0 - 914 m
(0 - 3000 ft) (room ambient)
10°- 35°C (50°- 95°F)
Operating temperature at
914 -2133 m
(3000 - 7000 ft) (room ambient)
10°- 32°C (50°- 90°F)
Operating humidity
8 - 80% (noncondensing)
Localized air temperature in PDU
60°C (140°F) maximum
© Copyright IBM Corp. 2006, 2007
51
Rated voltage
1. 220 - 240 V ac, 32 amps, single-phase
2. 200 - 208 V ac, 48 amps, single-phase
3. 220 - 240 V ac, 63 amps, single-phase
4. 220 - 240 V ac, 32 amps, three-phase Wye
5. 200 - 208 V ac, 24 amps, single-phase
6. 200 - 208 V ac, 48 amps, three-phase Delta
7. 200 - 208 V ac, 48 amps, single-phase
8. 220 - 240 V ac, 63 amps, single-phase
9. 220 - 240 V ac, 32 amps, three-phase Wye
10. 200 - 208 V ac, 48 amps, three-phase Delta
Rated frequency
Maximum power rating
50-60 Hz
1. 7680 VA
2. 9984 VA
3. 15120 VA
4. 23040 VA
5. 4992 VA
6. 17292 VA
7. 9984 VA
8. 15120 VA
9. 23040 VA
10. 17292 VA
Circuit breakers
Power cord
Six double-pole branch rated circuit breakers rated
at 20 amps
1. One IEC 309 2P+N+Gnd connector rated at
32 amps
2. One IEC 309 2P+Gnd connector rated at 60
amps
3. One IEC 309 2P+N+Gnd connector rated at
63 amps
4. One IEC 309 3P+N+Gnd connector rated at
32 amps
5. One Nema L6-30P connector rated at 30
amps
6. One IEC 309 3P+Gnd connector rated at 60
amps
7. One IEC 309 2P+Gnd connector rated at 60
amps
8. One IEC 309 2P+N+Gnd connector rated at
63 amps
9. One IEC 309 3P+N+Gnd connector rated at
32 amps
10. One IEC 309 3P+Gnd connector rated at 60
amps
Power outlets
52
Six IEC 320-C19 outlets rated at 16 amps (VDE) /
20 amps (UL/CSA)
Twelve IEC 320-C13 outlets rated at 10 amps
(VDE) / 15 amps (UL/CSA)
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
You must connect the connector on the power cord that comes with your PDU to a
properly wired and grounded outlet. The following table shows illustrations of the
power cord connector and the correct outlet for each of the PDUs.
PDU
v DPI 32 amp/250 V 3-phase
Enterprise C13 PDU with IEC
309 3P+N+Gnd connector
v DPI 32 amp/250 V 3-phase
Enterprise C19 PDU with IEC
309 3P+N+Gnd connector
v DPI 32 amp/250 V 1-phase
Enterprise C13 PDU with IEC
309 2P+N+Gnd connector
Plug
Outlet
L3
Rating
L2
N
G
L3
L2
L1
L1
N
N
32 amps,
220-240/380-415 V
ac
IEC 309
3P+N+Gnd
G
32 amps, 250 V ac
IEC 309 P+N+Gnd
L
L
N
G
G
v DPI 63 amp/250 V 1-phase
Enterprise C13 PDU with IEC
309 2P+N+Gnd connector
N
L
L
v DPI 63 amp/250 V 1-phase
Enterprise C19 PDU with IEC
309 2P+N+Gnd connector
v DPI 30 amp/208 V 1-phase
Enterprise C13 PDU with
Nema L6-30P connector
63 amps, 250 V ac
IEC 309
3P+N+Gnd
N
G
G
X
G
G
Y
v DPI 60 amp/208 V 1-phase
Enterprise C13 PDU with IEC
309 2P+Gnd connector
Y
L2
v DPI 60 amp/208 V 1-phase
Enterprise C19 PDU with IEC
309 2P+Gnd connector
v DPI 60 amp/208 V 3-phase
Enterprise C19 PDU with IEC
309 3P+Gnd connector
v DPI 60 amp/208 V 3-phase
Enterprise C13 PDU with IEC
3P+Gnd connector
30 amps, 250 V ac
NEMA L6-30
X
60 amps, 250 V ac
IEC 309 2P+Gnd
L1
L1
L2
G
G
60 amps, 208 V ac
IEC 309 3P+Gnd
L1
L2
G
G L2
L3
L3
Chapter 8. PDU specifications
53
54
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Appendix A. Getting help and technical assistance
If you need help, service, or technical assistance or just want more information
about IBM products, you will find a wide variety of sources available from IBM to
assist you. This section contains information about where to go for additional
information about IBM and IBM products, what to do if you experience a problem
with your system, and whom to call for service, if it is necessary.
Before you call
Before you call, make sure that you have taken these steps to try to solve the
problem yourself:
v Check all cables to make sure that they are connected.
v Check the power switches to make sure that the system and any optional
devices are turned on.
v Use the troubleshooting information in your system documentation, and use the
diagnostic tools that come with your system. Information about diagnostic tools is
in the Problem Determination and Service Guide on the IBM Documentation CD
that comes with your system.
v Go to the IBM support Web site at http://www.ibm.com/systems/support/ to check
for technical information, hints, tips, and new device drivers or to submit a
request for information.
You can solve many problems without outside assistance by following the
troubleshooting procedures that IBM provides in the online help or in the
documentation that is provided with your IBM product. The documentation that
comes with IBM systems also describes the diagnostic tests that you can perform.
Most systems, operating systems, and programs come with documentation that
contains troubleshooting procedures and explanations of error messages and error
codes. If you suspect a software problem, see the documentation for the operating
system or program.
Using the documentation
Information about your IBM system and preinstalled software, if any, or optional
device is available in the documentation that comes with the product. That
documentation can include printed documents, online documents, readme files, and
help files. See the troubleshooting information in your system documentation for
instructions for using the diagnostic programs. The troubleshooting information or
the diagnostic programs might tell you that you need additional or updated device
drivers or other software. IBM maintains pages on the World Wide Web where you
can get the latest technical information and download device drivers and updates.
To access these pages, go to http://www.ibm.com/systems/support/ and follow the
instructions. Also, some documents are available through the IBM Publications
Center at http://www.ibm.com/shop/publications/order/.
Getting help and information from the World Wide Web
On the World Wide Web, the IBM Web site has up-to-date information about IBM
systems, optional devices, services, and support. The address for IBM System x™
and xSeries® information is http://www.ibm.com/systems/x/. The address for IBM
BladeCenter® information is http://www.ibm.com/systems/bladecenter/. The address
for IBM IntelliStation® information is http://www.ibm.com/intellistation/.
© Copyright IBM Corp. 2006, 2007
55
You can find service information for IBM systems and optional devices at
http://www.ibm.com/systems/support/.
Software service and support
Through IBM Support Line, you can get telephone assistance, for a fee, with usage,
configuration, and software problems with System x and xSeries servers,
BladeCenter products, IntelliStation workstations, and appliances. For information
about which products are supported by Support Line in your country or region, see
http://www.ibm.com/services/sl/products/.
For more information about Support Line and other IBM services, see
http://www.ibm.com/services/, or see http://www.ibm.com/planetwide/ for support
telephone numbers. In the U.S. and Canada, call 1-800-IBM-SERV
(1-800-426-7378).
Hardware service and support
You can receive hardware service through IBM Services or through your IBM
reseller, if your reseller is authorized by IBM to provide warranty service. See
http://www.ibm.com/planetwide/ for support telephone numbers, or in the U.S. and
Canada, call 1-800-IBM-SERV (1-800-426-7378).
In the U.S. and Canada, hardware service and support is available 24 hours a day,
7 days a week. In the U.K., these services are available Monday through Friday,
from 9 a.m. to 6 p.m.
IBM Taiwan product service
IBM Taiwan product service contact information:
IBM Taiwan Corporation
3F, No 7, Song Ren Rd.
Taipei, Taiwan
Telephone: 0800-016-888
56
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Appendix B. IBM Statement of Limited Warranty Z125-4753-08
04/2004
Part 1 - General Terms
Part 1 - General Terms
This Statement of Limited Warranty includes Part 1 - General Terms, Part 2 Country-unique Terms, and Part 3 - Warranty Information. The terms of Part 2
replace or modify those of Part 1. The warranties provided by IBM in this Statement
of Limited Warranty apply only to Machines you purchase for your use, and not for
resale. The term “Machine” means an IBM machine, its features, conversions,
upgrades, elements, or accessories, or any combination of them. The term
“Machine” does not include any software programs, whether pre-loaded with the
Machine, installed subsequently or otherwise. Nothing in this Statement of
Limited Warranty affects any statutory rights of consumers that cannot be
waived or limited by contract.
What this Warranty Covers
IBM warrants that each Machine 1) is free from defects in materials and
workmanship and 2) conforms to IBM’s Official Published Specifications
(“Specifications”) which are available on request. The warranty period for the
Machine starts on the original Date of Installation and is specified in Part 3 Warranty Information. The date on your invoice or sales receipt is the Date of
Installation unless IBM or your reseller informs you otherwise. Many features,
conversions, or upgrades involve the removal of parts and their return to IBM. A
part that replaces a removed part will assume the warranty service status of the
removed part. Unless IBM specifies otherwise, these warranties apply only in the
country or region in which you purchased the Machine.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE
ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE
EXCLUSION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH WARRANTIES
ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES
APPLY AFTER THAT PERIOD. SOME STATES OR JURISDICTIONS DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
What this Warranty Does not Cover
This warranty does not cover the following:
v any software programs, whether pre-loaded or shipped with the Machine, or
installed subsequently;
v failure resulting from misuse (including but not limited to use of any Machine
capacity or capability, other than that authorized by IBM in writing), accident,
modification, unsuitable physical or operating environment, or improper
maintenance by you;
v failure caused by a product for which IBM is not responsible; and
v any non-IBM products, including those that IBM may procure and provide with or
integrate into an IBM Machine at your request.
© Copyright IBM Corp. 2006, 2007
57
The warranty is voided by removal or alteration of identification labels on the
Machine or its parts.
IBM does not warrant uninterrupted or error-free operation of a Machine.
Any technical or other support provided for a Machine under warranty, such as
assistance with “how-to” questions and those regarding Machine set-up and
installation, is provided WITHOUT WARRANTIES OF ANY KIND.
How to Obtain Warranty Service
If the Machine does not function as warranted during the warranty period, contact
IBM or your reseller to obtain warranty service. If you do not register the Machine
with IBM, you may be required to present proof of purchase as evidence of your
entitlement to warranty service.
What IBM Will Do to Correct Problems
When you contact IBM for service, you must follow the problem determination and
resolution procedures that IBM specifies. An initial diagnosis of your problem can be
made either by a technician over the telephone or electronically by access to an
IBM website.
The type of warranty service applicable to your Machine is specified in Part 3 Warranty Information.
You are responsible for downloading and installing designated Machine Code
(microcode, basic input/output system code (called “BIOS”), utility programs, device
drivers, and diagnostics delivered with an IBM Machine) and other software updates
from an IBM Internet Web site or from other electronic media, and following the
instructions that IBM provides.
If your problem can be resolved with a Customer Replaceable Unit (“CRU”) (e.g.,
keyboard, mouse, speaker, memory, hard disk drive), IBM will ship the CRU to you
for you to install.
If the Machine does not function as warranted during the warranty period and your
problem cannot be resolved over the telephone or electronically, through your
application of Machine Code or software updates, or with a CRU, IBM or your
reseller, if approved by IBM to provide warranty service, will either, at its discretion,
1) repair it to make it function as warranted, or 2) replace it with one that is at least
functionally equivalent. If IBM is unable to do either, you may return the Machine to
your place of purchase and your money will be refunded.
IBM or your reseller will also manage and install selected engineering changes that
apply to the Machine.
Exchange of a Machine or Part
When the warranty service involves the exchange of a Machine or part, the item
IBM or your reseller replaces becomes its property and the replacement becomes
yours. You represent that all removed items are genuine and unaltered. The
replacement may not be new, but will be in good working order and at least
functionally equivalent to the item replaced. The replacement assumes the warranty
service status of the replaced item.
58
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Your Additional Responsibilities
Before IBM or your reseller exchanges a Machine or part, you agree to remove all
features, parts, options, alterations, and attachments not under warranty service.
You also agree to:
1. ensure that the Machine is free of any legal obligations or restrictions that
prevent its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided:
a. follow the service request procedures that IBM or your reseller provides;
b. backup or secure all programs, data, and funds contained in the Machine;
c. provide IBM or your reseller with sufficient, free, and safe access to your
facilities to permit IBM to fulfill its obligations; and
d. inform IBM or your reseller of changes in the Machine’s location.
4. (a) ensure all information about identified or identifiable individuals (Personal
Data) is deleted from the Machine (to the extent technically possible), (b) allow
IBM, your reseller or an IBM supplier to process on your behalf any remaining
Personal Data as IBM or your reseller considers necessary to fulfill its
obligations under this Statement of Limited Warranty (which may include
shipping the Machine for such processing to other IBM service locations around
the world), and (c) ensure that such processing complies with any laws
applicable to such Personal Data.
Limitation of Liability
IBM is responsible for loss of, or damage to, your Machine only while it is 1) in
IBM’s possession or 2) in transit in those cases where IBM is responsible for the
transportation charges.
Neither IBM nor your reseller are responsible for any of your confidential,
proprietary or personal information contained in a Machine which you return to IBM
for any reason. You should remove all such information from the Machine prior to its
return.
Circumstances may arise where, because of a default on IBM’s part or other
liability, you are entitled to recover damages from IBM. In each such instance,
regardless of the basis on which you are entitled to claim damages from IBM
(including fundamental breach, negligence, misrepresentation, or other contract or
tort claim), except for any liability that cannot be waived or limited by applicable
laws, IBM is liable for no more than
1. damages for bodily injury (including death) and damage to real property and
tangible personal property; and
2. the amount of any other actual direct damages, up to the charges (if recurring,
12 months’ charges apply) for the Machine that is subject of the claim. For
purposes of this item, the term “Machine” includes Machine Code and Licensed
Internal Code (“LIC”).
This limit also applies to IBM’s suppliers and your reseller. It is the maximum for
which IBM, its suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS
LIABLE FOR ANY OF THE FOLLOWING EVEN IF INFORMED OF THEIR
POSSIBILITY: 1) THIRD PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS OF,
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
59
OR DAMAGE TO, DATA; 3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES
OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES; OR 4) LOST
PROFITS, BUSINESS REVENUE, GOODWILL OR ANTICIPATED SAVINGS.
SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. SOME STATES
OR JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU.
Governing Law
Both you and IBM consent to the application of the laws of the country in which you
acquired the Machine to govern, interpret, and enforce all of your and IBM’s rights,
duties, and obligations arising from, or relating in any manner to, the subject matter
of this Statement of Limited Warranty, without regard to conflict of law principles.
THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR
JURISDICTION TO JURISDICTION.
Jurisdiction
All of our rights, duties, and obligations are subject to the courts of the country in
which you acquired the Machine.
Part 2 - Country-unique Terms
AMERICAS
ARGENTINA
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the Ordinary Commercial Court of the city of Buenos Aires.
BOLIVIA
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the courts of the city of La Paz.
BRAZIL
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the court of Rio de Janeiro, RJ.
CHILE
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the Civil Courts of Justice of Santiago.
60
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
COLOMBIA
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the Judges of the Republic of Colombia.
EQUADOR
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the Judges of Quito.
MEXICO
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the Federal Courts of Mexico City, Federal District.
PARAGUAY
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the courts of the city of Asuncion.
PERU
Limitation of Liability: The following is added at the end of this section:
In accordance with Article 1328 of the Peruvian Civil Code the limitations and
exclusions specified in this section will not apply to damages caused by IBM’s willful
misconduct (“dolo”) or gross negligence (“culpa inexcusable”).
URUGUAY
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the City of Montevideo Court’s Jurisdiction.
VENEZUELA
Jurisdiction: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the Courts of the Metropolitan Area Of the City of Caracas.
NORTH AMERICA
How to Obtain Warranty Service: The following is added to this Section:
To obtain warranty service from IBM in Canada or the United States, call
1-800-IBM-SERV (426-7378).
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
61
CANADA
Limitation of Liability: The following replaces item 1 of this section:
1. damages for bodily injury (including death) or physical harm to real property
and tangible personal property caused by IBM’s negligence; and
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws in the Province of Ontario.
UNITED STATES
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of the State of New York.
ASIA PACIFIC
AUSTRALIA
What this Warranty Covers: The following paragraph is added to this section:
The warranties specified in this Section are in addition to any rights you may have
under the Trade Practices Act 1974 or other similar legislation and are only limited
to the extent permitted by the applicable legislation.
Limitation of Liability: The following is added to this section:
Where IBM is in breach of a condition or warranty implied by the Trade Practices
Act 1974 or other similar legislation, IBM’s liability is limited to the repair or
replacement of the goods or the supply of equivalent goods. Where that condition
or warranty relates to right to sell, quiet possession or clear title, or the goods are of
a kind ordinarily acquired for personal, domestic or household use or consumption,
then none of the limitations in this paragraph apply.
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of the State or Territory.
CAMBODIA AND LAOS
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of the State of New York, United States of America.
CAMBODIA, INDONESIA, AND LAOS
Arbitration: The following is added under this heading:
Disputes arising out of or in connection with this Statement of Limited Warranty
shall be finally settled by arbitration which shall be held in Singapore in accordance
with the Arbitration Rules of Singapore International Arbitration Center (“SIAC
Rules”) then in effect. The arbitration award shall be final and binding for the parties
without appeal and shall be in writing and set forth the findings of fact and the
conclusions of law.
The number of arbitrators shall be three, with each side to the dispute being entitled
to appoint one arbitrator. The two arbitrators appointed by the parties shall appoint
a third arbitrator who shall act as chairman of the proceedings. Vacancies in the
62
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
post of chairman shall be filled by the president of the SIAC. Other vacancies shall
be filled by the respective nominating party. Proceedings shall continue from the
stage they were at when the vacancy occurred.
If one of the parties refuses or otherwise fails to appoint an arbitrator within 30 days
of the date the other party appoints its, the first appointed arbitrator shall be the
sole arbitrator, provided that the arbitrator was validly and properly appointed.
All proceedings shall be conducted, including all documents presented in such
proceedings, in the English language. The English language version of this
Statement of Limited Warranty prevails over any other language version.
HONG KONG S.A.R. OF CHINA AND MACAU S.A.R. OF CHINA
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of Hong Kong Special Administrative Region of China.
INDIA
Limitation of Liability: The following replaces items 1 and 2 of this section:
1. liability for bodily injury (including death) or damage to real property and tangible
personal property will be limited to that caused by IBM’s negligence; and
2. as to any other actual damage arising in any situation involving nonperformance
by IBM pursuant to, or in any way related to the subject of this Statement of
Limited Warranty, the charge paid by you for the individual Machine that is the
subject of the claim. For purposes of this item, the term “Machine” includes
Machine Code and Licensed Internal Code (“LIC”).
Arbitration: The following is added under this heading:
Disputes arising out of or in connection with this Statement of Limited Warranty
shall be finally settled by arbitration which shall be held in Bangalore, India in
accordance with the laws of India then in effect. The arbitration award shall be final
and binding for the parties without appeal and shall be in writing and set forth the
findings of fact and the conclusions of law.
The number of arbitrators shall be three, with each side to the dispute being entitled
to appoint one arbitrator. The two arbitrators appointed by the parties shall appoint
a third arbitrator who shall act as chairman of the proceedings. Vacancies in the
post of chairman shall be filled by the president of the Bar Council of India. Other
vacancies shall be filled by the respective nominating party. Proceedings shall
continue from the stage they were at when the vacancy occurred.
If one of the parties refuses or otherwise fails to appoint an arbitrator within 30 days
of the date the other party appoints its, the first appointed arbitrator shall be the
sole arbitrator, provided that the arbitrator was validly and properly appointed.
All proceedings shall be conducted, including all documents presented in such
proceedings, in the English language. The English language version of this
Statement of Limited Warranty prevails over any other language version.
JAPAN
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
63
Governing Law: The following sentence is added to this section:
Any doubts concerning this Statement of Limited Warranty will be initially resolved
between us in good faith and in accordance with the principle of mutual trust.
MALAYSIA
Limitation of Liability: The word “SPECIAL” in item 3 of the fifth paragraph is
deleted.
NEW ZEALAND
What this Warranty Covers: The following paragraph is added to this section:
The warranties specified in this section are in addition to any rights you may have
under the Consumer Guarantees Act 1993 or other legislation which cannot be
excluded or limited. The Consumer Guarantees Act 1993 will not apply in respect of
any goods which IBM provides, if you require the goods for the purposes of a
business as defined in that Act.
Limitation of Liability: The following is added to this section:
Where Machines are not acquired for the purposes of a business as defined in the
Consumer Guarantees Act 1993, the limitations in this section are subject to the
limitations in that Act.
PEOPLE’S REPUBLIC OF CHINA (PRC)
Governing Law: The following replaces “laws of the country in which you acquired
the Machine” in the first sentence:
laws of the State of New York, United States of America (except when local law
requires otherwise).
PHILIPPINES
Limitation of Liability: Item 3 in the fifth paragraph is replaced by the following:
SPECIAL (INCLUDING NOMINAL AND EXEMPLARY DAMAGES), MORAL,
INCIDENTAL, OR INDIRECT DAMAGES FOR ANY ECONOMIC
CONSEQUENTIAL DAMAGES; OR
Arbitration: The following is added under this heading:
Disputes arising out of or in connection with this Statement of Limited Warranty
shall be finally settled by arbitration which shall be held in Metro Manila, Philippines
in accordance with the laws of the Philippines then in effect. The arbitration award
shall be final and binding for the parties without appeal and shall be in writing and
set forth the findings of fact and the conclusions of law.
The number of arbitrators shall be three, with each side to the dispute being entitled
to appoint one arbitrator. The two arbitrators appointed by the parties shall appoint
a third arbitrator who shall act as chairman of the proceedings. Vacancies in the
post of chairman shall be filled by the president of the Philippine Dispute Resolution
Center, Inc. Other vacancies shall be filled by the respective nominating party.
Proceedings shall continue from the stage they were at when the vacancy occurred.
64
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
If one of the parties refuses or otherwise fails to appoint an arbitrator within 30 days
of the date the other party appoints its, the first appointed arbitrator shall be the
sole arbitrator, provided that the arbitrator was validly and properly appointed.
All proceedings shall be conducted, including all documents presented in such
proceedings, in the English language. The English language version of this
Statement of Limited Warranty prevails over any other language version.
SINGAPORE
Limitation of Liability: The words “SPECIAL” and “ECONOMIC” in item 3 in the
fifth paragraph are deleted.
EUROPE, MIDDLE EAST, AFRICA (EMEA)
THE FOLLOWING TERMS APPLY TO ALL EMEA COUNTRIES:
The terms of this Statement of Limited Warranty apply to Machines purchased from
IBM or an IBM reseller.
How to Obtain Warranty Service:
Add the following paragraph in Western Europe (Andorra, Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, Netherlands, Norway, Poland, Portugal, San Marino, Slovakia, Slovenia,
Spain, Sweden, Switzerland, United Kingdom, Vatican State, and any country
subsequently added to the European Union, as from the date of accession):
The warranty for Machines acquired in Western Europe shall be valid and
applicable in all Western Europe countries provided the Machines have been
announced and made available in such countries.
If you purchase a Machine in one of the Western European countries, as defined
above, you may obtain warranty service for that Machine in any of those countries
from either (1) an IBM reseller approved to perform warranty service or (2) from
IBM, provided the Machine has been announced and made available by IBM in the
country in which you wish to obtain service.
If you purchased a Personal Computer Machine in Albania, Armenia, Belarus,
Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic, Georgia, Hungary,
Kazakhstan, Kyrgyzstan, Federal Republic of Yugoslavia, Former Yugoslav Republic
of Macedonia (FYROM), Moldova, Poland, Romania, Russia, Slovak Republic,
Slovenia, or Ukraine, you may obtain warranty service for that Machine in any of
those countries from either (1) an IBM reseller approved to perform warranty
service or (2) from IBM.
If you purchase a Machine in a Middle Eastern or African country, you may obtain
warranty service for that Machine from the IBM entity within the country of
purchase, if that IBM entity provides warranty service in that country, or from an
IBM reseller, approved by IBM to perform warranty service on that Machine in that
country. Warranty service in Africa is available within 50 kilometers of an IBM
approved service provider. You are responsible for transportation costs for Machines
located outside 50 kilometers of an IBM approved service provider.
Governing Law:
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
65
The phrase “the laws of the country in which you acquired the Machine” is replaced
by:
1) “the laws of Austria” in Albania, Armenia, Azerbaijan, Belarus,
Bosnia-Herzegovina, Bulgaria, Croatia, Georgia, Hungary, Kazakhstan,
Kyrgyzstan, FYR Macedonia, Moldova, Poland, Romania, Russia, Slovakia,
Slovenia, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, and FR Yugoslavia; 2)
“the laws of France” in Algeria, Benin, Burkina Faso, Cameroon, Cape Verde,
Central African Republic, Chad, Comoros, Congo Republic, Djibouti,
Democratic Republic of Congo, Equatorial Guinea, French Guiana, French
Polynesia, Gabon, Gambia, Guinea, Guinea-Bissau, Ivory Coast, Lebanon,
Madagascar, Mali, Mauritania, Mauritius, Mayotte, Morocco, New Caledonia,
Niger, Reunion, Senegal, Seychelles, Togo, Tunisia, Vanuatu, and Wallis &
Futuna; 3) “the laws of Finland” in Estonia, Latvia, and Lithuania; 4) “the laws of
England” in Angola, Bahrain, Botswana, Burundi, Egypt, Eritrea, Ethiopia,
Ghana, Jordan, Kenya, Kuwait, Liberia, Malawi, Malta, Mozambique, Nigeria,
Oman, Pakistan, Qatar, Rwanda, Sao Tome, Saudi Arabia, Sierra Leone,
Somalia, Tanzania, Uganda, United Arab Emirates, the United Kingdom, West
Bank/Gaza, Yemen, Zambia, and Zimbabwe; and 5) “the laws of South Africa” in
South Africa, Namibia, Lesotho and Swaziland.
Jurisdiction: The following exceptions are added to this section:
1) In Austria the choice of jurisdiction for all disputes arising out of this Statement
of Limited Warranty and relating thereto, including its existence, will be the
competent court of law in Vienna, Austria (Inner-City); 2) in Angola, Bahrain,
Botswana, Burundi, Egypt, Eritrea, Ethiopia, Ghana, Jordan, Kenya, Kuwait,
Liberia, Malawi, Malta, Mozambique, Nigeria, Oman, Pakistan, Qatar, Rwanda,
Sao Tome, Saudi Arabia, Sierra Leone, Somalia, Tanzania, Uganda, United
Arab Emirates, West Bank/Gaza, Yemen, Zambia, and Zimbabwe all disputes
arising out of this Statement of Limited Warranty or related to its execution,
including summary proceedings, will be submitted to the exclusive jurisdiction of the
English courts; 3) in Belgium and Luxembourg, all disputes arising out of this
Statement of Limited Warranty or related to its interpretation or its execution, the
law, and the courts of the capital city, of the country of your registered office and/or
commercial site location only are competent; 4) in France, Algeria, Benin, Burkina
Faso, Cameroon, Cape Verde, Central African Republic, Chad, Comoros,
Congo Republic, Djibouti, Democratic Republic of Congo, Equatorial Guinea,
French Guiana, French Polynesia, Gabon, Gambia, Guinea, Guinea-Bissau,
Ivory Coast, Lebanon, Madagascar, Mali, Mauritania, Mauritius, Mayotte,
Morocco, New Caledonia, Niger, Reunion, Senegal, Seychelles, Togo, Tunisia,
Vanuatu, and Wallis & Futuna all disputes arising out of this Statement of Limited
Warranty or related to its violation or execution, including summary proceedings, will
be settled exclusively by the Commercial Court of Paris; 5) in Russia, all disputes
arising out of or in relation to the interpretation, the violation, the termination, the
nullity of the execution of this Statement of Limited Warranty shall be settled by
Arbitration Court of Moscow; 6) in South Africa, Namibia, Lesotho and
Swaziland, both of us agree to submit all disputes relating to this Statement of
Limited Warranty to the jurisdiction of the High Court in Johannesburg; 7) in Turkey
all disputes arising out of or in connection with this Statement of Limited Warranty
shall be resolved by the Istanbul Central (Sultanahmet) Courts and Execution
Directorates of Istanbul, the Republic of Turkey; 8) in each of the following specified
countries, any legal claim arising out of this Statement of Limited Warranty will be
brought before, and settled exclusively by, the competent court of a) Athens for
Greece, b) Tel Aviv-Jaffa for Israel, c) Milan for Italy, d) Lisbon for Portugal, and e)
66
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Madrid for Spain; and 9) in the United Kingdom, both of us agree to submit all
disputes relating to this Statement of Limited Warranty to the jurisdiction of the
English courts.
Arbitration: The following is added under this heading:
In Albania, Armenia, Azerbaijan, Belarus, Bosnia-Herzegovina, Bulgaria,
Croatia, Georgia, Hungary, Kazakhstan, Kyrgyzstan, FYR Macedonia, Moldova,
Poland, Romania, Russia, Slovakia, Slovenia, Tajikistan, Turkmenistan,
Ukraine, Uzbekistan, and FR Yugoslavia all disputes arising out of this Statement
of Limited Warranty or related to its violation, termination or nullity will be finally
settled under the Rules of Arbitration and Conciliation of the International Arbitral
Center of the Federal Economic Chamber in Vienna (Vienna Rules) by three
arbitrators appointed in accordance with these rules. The arbitration will be held in
Vienna, Austria, and the official language of the proceedings will be English. The
decision of the arbitrators will be final and binding upon both parties. Therefore,
pursuant to paragraph 598 (2) of the Austrian Code of Civil Procedure, the parties
expressly waive the application of paragraph 595 (1) figure 7 of the Code. IBM may,
however, institute proceedings in a competent court in the country of installation.
In Estonia, Latvia and Lithuania all disputes arising in connection with this
Statement of Limited Warranty will be finally settled in arbitration that will be held in
Helsinki, Finland in accordance with the arbitration laws of Finland then in effect.
Each party will appoint one arbitrator. The arbitrators will then jointly appoint the
chairman. If arbitrators cannot agree on the chairman, then the Central Chamber of
Commerce in Helsinki will appoint the chairman.
EUROPEAN UNION (EU)
THE FOLLOWING TERMS APPLY TO ALL EU COUNTRIES:
The warranty for Machines acquired in EU countries is valid and applicable in all
EU countries provided the Machines have been announced and made available in
such countries.
How to Obtain Warranty Service: The following is added to this section:
To obtain warranty service from IBM in EU countries, see the telephone listing in
Part 3 - Warranty Information.
You may contact IBM at the following address:
IBM Warranty & Service Quality Dept.
PO Box 30
Spango Valley
Greenock
Scotland PA16 0AH
CONSUMERS
Consumers have legal rights under applicable national legislation governing the sale
of consumer goods. Such rights are not affected by the warranties provided in this
Statement of Limited Warranty.
AUSTRIA, DENMARK, FINLAND, GREECE, ITALY, NETHERLANDS, NORWAY,
PORTUGAL, SPAIN, SWEDEN AND SWITZERLAND
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
67
Limitation of Liability: The following replaces the terms of this section in its
entirety:
Except as otherwise provided by mandatory law:
1. IBM’s liability for any damages and losses that may arise as a consequence of
the fulfillment of its obligations under or in connection with this Statement of
Limited Warranty or due to any other cause related to this Statement of Limited
Warranty is limited to the compensation of only those damages and losses
proved and actually arising as an immediate and direct consequence of the
non-fulfillment of such obligations (if IBM is at fault) or of such cause, for a
maximum amount equal to the charges you paid for the Machine. For purposes
of this item, the term “Machine” includes Machine Code and Licensed Internal
Code (“LIC”).
The above limitation shall not apply to damages for bodily injuries (including
death) and damages to real property and tangible personal property for which
IBM is legally liable.
2. UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS
LIABLE FOR ANY OF THE FOLLOWING, EVEN IF INFORMED OF THEIR
POSSIBILITY: 1) LOSS OF, OR DAMAGE TO, DATA; 2) INCIDENTAL OR
INDIRECT DAMAGES, OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES; 3) LOST PROFITS, EVEN IF THEY ARISE AS AN IMMEDIATE
CONSEQUENCE OF THE EVENT THAT GENERATED THE DAMAGES; OR
4) LOSS OF BUSINESS, REVENUE, GOODWILL, OR ANTICIPATED
SAVINGS.
FRANCE AND BELGIUM
Limitation of Liability: The following replaces the terms of this section in its
entirety:
Except as otherwise provided by mandatory law:
1. IBM’s liability for any damages and losses that may arise as a consequence of
the fulfillment of its obligations under or in connection with this Statement of
Limited Warranty is limited to the compensation of only those damages and
losses proved and actually arising as an immediate and direct consequence of
the non-fulfillment of such obligations (if IBM is at fault), for a maximum amount
equal to the charges you paid for the Machine that has caused the damages.
For purposes of this item, the term “Machine” includes Machine Code and
Licensed Internal Code (“LIC”).
The above limitation shall not apply to damages for bodily injuries (including
death) and damages to real property and tangible personal property for which
IBM is legally liable.
2. UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS
LIABLE FOR ANY OF THE FOLLOWING, EVEN IF INFORMED OF THEIR
POSSIBILITY: 1) LOSS OF, OR DAMAGE TO, DATA; 2) INCIDENTAL OR
INDIRECT DAMAGES, OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES; 3) LOST PROFITS, EVEN IF THEY ARISE AS AN IMMEDIATE
CONSEQUENCE OF THE EVENT THAT GENERATED THE DAMAGES; OR
4) LOSS OF BUSINESS, REVENUE, GOODWILL, OR ANTICIPATED
SAVINGS.
THE FOLLOWING TERMS APPLY TO THE COUNTRY SPECIFIED:
AUSTRIA
68
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
The provisions of this Statement of Limited Warranty replace any applicable
statutory warranties.
What this Warranty Covers: The following replaces the first sentence of the first
paragraph of this section:
The warranty for an IBM Machine covers the functionality of the Machine for its
normal use and the Machine’s conformity to its Specifications.
The following paragraphs are added to this section:
The limitation period for consumers in action for breach of warranty is the statutory
period as a minimum. In case IBM or your reseller is unable to repair an IBM
Machine, you can alternatively ask for a partial refund as far as justified by the
reduced value of the unrepaired Machine or ask for a cancellation of the respective
agreement for such Machine and get your money refunded.
The second paragraph does not apply.
What IBM Will Do to Correct Problems: The following is added to this section:
During the warranty period, IBM will reimburse you for the transportation charges
for the delivery of the failing Machine to IBM.
Limitation of Liability: The following paragraph is added to this section:
The limitations and exclusions specified in the Statement of Limited Warranty will
not apply to damages caused by IBM with fraud or gross negligence and for
express warranty.
The following sentence is added to the end of item 2:
IBM’s liability under this item is limited to the violation of essential contractual terms
in cases of ordinary negligence.
EGYPT
Limitation of Liability: The following replaces item 2 in this section:
as to any other actual direct damages, IBM’s liability will be limited to the total
amount you paid for the Machine that is the subject of the claim. For purposes of
this item, the term “Machine” includes Machine Code and Licensed Internal Code
(“LIC”).
Applicability of suppliers and resellers (unchanged).
FRANCE
Limitation of Liability: The following replaces the second sentence of the first
paragraph of this section:
In such instances, regardless of the basis on which you are entitled to claim
damages from IBM, IBM is liable for no more than: (items 1 and 2 unchanged).
GERMANY
What this Warranty Covers: The following replaces the first sentence of the first
paragraph of this section:
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
69
The warranty for an IBM Machine covers the functionality of the Machine for its
normal use and the Machine’s conformity to its Specifications.
The following paragraphs are added to this section:
The minimum warranty period for Machines is twelve months. In case IBM or your
reseller is unable to repair an IBM Machine, you can alternatively ask for a partial
refund as far as justified by the reduced value of the unrepaired Machine or ask for
a cancellation of the respective agreement for such Machine and get your money
refunded.
The second paragraph does not apply.
What IBM Will Do to Correct Problems: The following is added to this section:
During the warranty period, transportation for delivery of the failing Machine to IBM
will be at IBM’s expense.
Limitation of Liability: The following paragraph is added to this section:
The limitations and exclusions specified in the Statement of Limited Warranty will
not apply to damages caused by IBM with fraud or gross negligence and for
express warranty.
The following sentence is added to the end of item 2:
IBM’s liability under this item is limited to the violation of essential contractual terms
in cases of ordinary negligence.
HUNGARY
Limitation of Liability: The following is added at the end of this section:
The limitation and exclusion specified herein shall not apply to liability for a breach
of contract damaging life, physical well-being, or health that has been caused
intentionally, by gross negligence, or by a criminal act.
The parties accept the limitations of liability as valid provisions and state that the
Section 314.(2) of the Hungarian Civil Code applies as the acquisition price as well
as other advantages arising out of the present Statement of Limited Warranty
balance this limitation of liability.
IRELAND
What this Warranty Covers: The following is added to this section:
Except as expressly provided in these terms and conditions, all statutory conditions,
including all warranties implied, but without prejudice to the generality of the
foregoing all warranties implied by the Sale of Goods Act 1893 or the Sale of
Goods and Supply of Services Act 1980 are hereby excluded.
Limitation of Liability: The following replaces the terms of this section in its
entirety:
For the purposes of this section, a “Default” means any act, statement, omission, or
negligence on the part of IBM in connection with, or in relation to, the subject matter
of this Statement of Limited Warranty in respect of which IBM is legally liable to
70
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
you, whether in contract or tort. A number of Defaults which together result in, or
contribute to, substantially the same loss or damage will be treated as one Default
occurring on the date of occurrence of the last such Default.
Circumstances may arise where, because of a Default, you are entitled to recover
damages from IBM.
This section sets out the extent of IBM’s liability and your sole remedy.
1. IBM will accept unlimited liability for death or personal injury caused by the
negligence of IBM.
2. Subject always to the Items for Which IBM is Not Liable below, IBM will
accept unlimited liability for physical damage to your tangible property resulting
from the negligence of IBM.
3. Except as provided in items 1 and 2 above, IBM’s entire liability for actual
damages for any one Default will not in any event exceed the greater of 1) EUR
125,000, or 2) 125% of the amount you paid for the Machine directly relating to
the Default.
Items for Which IBM is Not Liable
Save with respect to any liability referred to in item 1 above, under no
circumstances is IBM, its suppliers or resellers liable for any of the following, even if
IBM or they were informed of the possibility of such losses:
1. loss of, or damage to, data;
2. special, indirect, or consequential loss; or
3. loss of profits, business, revenue, goodwill, or anticipated savings.
SLOVAKIA
Limitation of Liability: The following is added to the end of the last paragraph:
The limitations apply to the extent they are not prohibited under §§ 373-386 of the
Slovak Commercial Code.
SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND
Limitation of Liability: The following is added to this section:
IBM’s entire liability to you for actual damages arising in all situations involving
nonperformance by IBM in respect of the subject matter of this Statement of
Warranty will be limited to the charge paid by you for the individual Machine that is
the subject of your claim from IBM.
UNITED KINGDOM
Limitation of Liability: The following replaces the terms of this section in its
entirety:
For the purposes of this section, a “Default” means any act, statement, omission, or
negligence on the part of IBM in connection with, or in relation to, the subject matter
of this Statement of Limited Warranty in respect of which IBM is legally liable to
you, whether in contract or tort. A number of Defaults which together result in, or
contribute to, substantially the same loss or damage will be treated as one Default.
Circumstances may arise where, because of a Default, you are entitled to recover
damages from IBM.
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
71
This section sets out the extent of IBM’s liability and your sole remedy.
1. IBM will accept unlimited liability for:
a. death or personal injury caused by the negligence of IBM; and
b. any breach of its obligations implied by Section 12 of the Sale of Goods Act
1979 or Section 2 of the Supply of Goods and Services Act 1982, or any
statutory modification or re-enactment of either such Section.
2. IBM will accept unlimited liability, subject always to the Items for Which IBM is
Not Liable below, for physical damage to your tangible property resulting from
the negligence of IBM.
3. IBM’s entire liability for actual damages for any one Default will not in any event,
except as provided in items 1 and 2 above, exceed the greater of 1) Pounds
Sterling 75,000, or 2) 125% of the total purchase price payable or the charges
for the Machine directly relating to the Default.
These limits also apply to IBM’s suppliers and resellers. They state the maximum
for which IBM and such suppliers and resellers are collectively responsible.
Items for Which IBM is Not Liable
Save with respect to any liability referred to in item 1 above, under no
circumstances is IBM or any of its suppliers or resellers liable for any of the
following, even if IBM or they were informed of the possibility of such losses:
1. loss of, or damage to, data;
2. special, indirect, or consequential loss; or
3. loss of profits, business, revenue, goodwill, or anticipated savings.
Part 3 - Warranty Information
This Part 3 provides information regarding the warranty applicable to your Machine,
including the warranty period and type of warranty service IBM provides.
Warranty Period
The warranty period may vary by country or region and is specified in the table
below.
Note: “Region” means either Hong Kong or Macau Special Administrative Region
of China.
A warranty period of 3 years on parts and 1 year on labor means that IBM provides
warranty service without charge for:
1. parts and labor during the first year of the warranty period; and
2. parts only, on an exchange basis, in the second and third years of the warranty
period. IBM will charge you for any labor provided in performance of the repair
or replacement(s) in the second and third year of the warranty period.
IBM DPI C13 PDU+, IBM DPI C13 3-phase PDU+,
IBM DPI C19 PDU+, and IBM DPI C19 3-phase PDU+
Country or Region of
Purchase
Warranty Period
Type of Warranty Service*
Worldwide
1 year
1
* See “Types of Warranty Service” for the legend and explanations of warranty-service
types.
72
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Types of Warranty Service
If required, IBM provides repair or exchange service depending on the type of
warranty service specified for your Machine in the above table and as described
below. Warranty service may be provided by your reseller if approved by IBM to
perform warranty service. Scheduling of service will depend upon the time of your
call and is subject to parts availability. Service levels are response time objectives
and are not guaranteed. The specified level of warranty service may not be
available in all worldwide locations, additional charges may apply outside IBM’s
normal service area, contact your local IBM representative or your reseller for
country and location specific information.
1. Customer Replaceable Unit (“CRU”) Service
IBM provides replacement CRUs to you for you to install. CRU information and
replacement instructions are shipped with your Machine and are available from
IBM at any time on your request. Installation of Tier 1 CRUs is your
responsibility. If IBM installs a Tier 1 CRU at your request, you will be charged
for the installation. You may install a Tier 2 CRU yourself or request IBM to
install it, at no additional charge, under the type of warranty service designated
for your Machine. IBM specifies in the materials shipped with a replacement
CRU whether a defective CRU must be returned to IBM. When return is
required, 1) return instructions and a container are shipped with the replacement
CRU, and 2) you may be charged for the replacement CRU if IBM does not
receive the defective CRU within 30 days of your receipt of the replacement.
2. On-site Service
IBM or your reseller will either repair or exchange the failing Machine at your
location and verify its operation. You must provide suitable working area to allow
disassembly and reassembly of the IBM Machine. The area must be clean, well
lit and suitable for the purpose. For some Machines, certain repairs may require
sending the Machine to an IBM service center.
3. Courier or Depot Service*
4.
5.
6.
7.
You will disconnect the failing Machine for collection arranged by IBM. IBM will
provide you with a shipping container for you to return your Machine to a
designated service center. A courier will pick up your Machine and deliver it to
the designated service center. Following its repair or exchange, IBM will arrange
the return delivery of the Machine to your location. You are responsible for its
installation and verification.
Customer Carry-In or Mail-In Service
You will deliver or mail as IBM specifies (prepaid unless IBM specifies
otherwise) the failing Machine suitably packaged to a location IBM designates.
After IBM has repaired or exchanged the Machine, IBM will make it available for
your collection or, for Mail-in Service, IBM will return it to you at IBM’s expense,
unless IBM specifies otherwise. You are responsible for the subsequent
installation and verification of the Machine.
CRU and On-site Service
This type of Warranty Service is a combination of Type 1 and Type 2 (see
above).
CRU and Courier or Depot Service
This type of Warranty Service is a combination of Type 1 and Type 3 (see
above).
CRU and Customer Carry-In or Mail-In Service
This type of Warranty Service is a combination of Type 1 and Type 4 (see
above).
Appendix B. IBM Statement of Limited Warranty Z125-4753-08 04/2004
73
When a 5, 6 or 7 type of warranty service is listed, IBM will determine which
type of warranty service is appropriate for the repair.
* This type of service is called ThinkPad EasyServ or EasyServ in some countries.
The IBM Machine Warranty World Wide Web site at http://www.ibm.com/servers/
support/machine_warranties/ provides a worldwide overview of IBM’s Limited
Warranty for Machines, a Glossary of IBM definitions, Frequently Asked Questions
(FAQs) and Support by Product (Machine) with links to Product Support pages. The
IBM Statement of Limited Warranty is also available on this site in 29
languages.
To obtain warranty service contact IBM or your IBM reseller. In Canada or the
United States, call 1-800-IBM-SERV (426-7378). In the EU countries, see the
telephone numbers below.
EU Country Telephone List
Phone numbers are subject to change without notice. For the warranty service
contact telephone number in a country subsequently added to the EU and not yet
reflected in the list below, contact IBM in that country or visit the website above for
a current telephone listing.
Austria -- +43-1-24592-5901
Latvia -- +386-61-1796-699
Belgium -- +32-70-23-3392
Lithuania -- +386-61-1796-699
Cyprus -- +357-22-841100
Luxembourg -- +352-298-977-5063
Czech Republic -- +420-2-7213-1316
Malta -- +356-23-4175
Denmark -- +45-4520-8200
Netherlands -- +31-20-514-5770
Estonia -- +386-61-1796-699
Poland -- +48-22-878-6999
Finland -- +358-8001-4260
Portugal -- +351-21-892-7147
France -- +33-238-557-450
Slovakia -- +421-2-4954-1217
Germany -- +49-1805-253553
Slovenia -- +386-1-4796-699
Greece -- +30-210-680-1700
Spain -- +34-91-714-7983
Hungary -- +36-1-382-5720
Sweden -- +46-8-477-4420
Ireland -- +353-1-815-4000
United Kingdom -- +44-0870-550-0900
Italy -- +39-800-820-094
74
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Appendix C. Notices
This information was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the
products and services currently available in your area. Any reference to an IBM
product, program, or service is not intended to state or imply that only that IBM
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any IBM intellectual property right may be
used instead. However, it is the user’s responsibility to evaluate and verify the
operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions, therefore, this statement may not apply to
you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements and/or
changes in the product(s) and/or the program(s) described in this publication at any
time without notice.
Any references in this information to non-IBM Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for this
IBM product, and use of those Web sites is at your own risk.
IBM may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.
Trademarks
The following terms are trademarks of International Business Machines Corporation
in the United States, other countries, or both:
IBM
IBM (logo)
Active Memory
Active PCI
Active PCI-X
© Copyright IBM Corp. 2006, 2007
FlashCopy
i5/OS
IntelliStation
NetBAY
Netfinity
TechConnect
Tivoli
Tivoli Enterprise
Update Connector
Wake on LAN
75
AIX
Alert on LAN
BladeCenter
Chipkill
e-business logo
Eserver
PowerExecutive
Predictive Failure Analysis
ServeRAID
ServerGuide
ServerProven
System x
XA-32
XA-64
X-Architecture
XpandOnDemand
xSeries
Intel, Intel Xeon, Itanium, and Pentium are trademarks of Intel Corporation in the
United States, other countries, or both.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in
the United States, other countries, or both.
Adobe and PostScript are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States, other countries, or both.
UNIX is a registered trademark of The Open Group in the United States and other
countries.
Java and all Java-based trademarks are trademarks of Sun Microsystems, Inc. in
the United States, other countries, or both.
Adaptec and HostRAID are trademarks of Adaptec, Inc., in the United States, other
countries, or both.
Linux is a registered trademark of Linus Torvalds in the United States, other
countries, or both.
Red Hat, the Red Hat “Shadow Man” logo, and all Red Hat-based trademarks and
logos are trademarks or registered trademarks of Red Hat, Inc., in the United States
and other countries.
Other company, product, or service names may be trademarks or service marks of
others.
Important notes
Processor speed indicates the internal clock speed of the microprocessor; other
factors also affect application performance.
CD or DVD drive speed is the variable read rate. Actual speeds vary and are often
less than the possible maximum.
When referring to processor storage, real and virtual storage, or channel volume,
KB stands for 1024 bytes, MB stands for 1 048 576 bytes, and GB stands for
1 073 741 824 bytes.
When referring to hard disk drive capacity or communications volume, MB stands
for 1 000 000 bytes, and GB stands for 1 000 000 000 bytes. Total user-accessible
capacity can vary depending on operating environments.
Maximum internal hard disk drive capacities assume the replacement of any
standard hard disk drives and population of all hard disk drive bays with the largest
currently supported drives that are available from IBM.
76
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Maximum memory might require replacement of the standard memory with an
optional memory module.
IBM makes no representation or warranties regarding non-IBM products and
services that are ServerProven®, including but not limited to the implied warranties
of merchantability and fitness for a particular purpose. These products are offered
and warranted solely by third parties.
IBM makes no representations or warranties with respect to non-IBM products.
Support (if any) for the non-IBM products is provided by the third party, not IBM.
Some software might differ from its retail version (if available) and might not include
user manuals or all program functionality.
Product recycling and disposal
This unit must be recycled or discarded according to applicable local and national
regulations. IBM encourages owners of information technology (IT) equipment to
responsibly recycle their equipment when it is no longer needed. IBM offers a
variety of product return programs and services in several countries to assist
equipment owners in recycling their IT products. Information on IBM product
recycling offerings can be found on IBM’s Internet site at http://www.ibm.com/ibm/
environment/products/index.shtml.
Esta unidad debe reciclarse o desecharse de acuerdo con lo establecido en la
normativa nacional o local aplicable. IBM recomienda a los propietarios de equipos
de tecnología de la información (TI) que reciclen responsablemente sus equipos
cuando éstos ya no les sean útiles. IBM dispone de una serie de programas y
servicios de devolución de productos en varios países, a fin de ayudar a los
propietarios de equipos a reciclar sus productos de TI. Se puede encontrar
información sobre las ofertas de reciclado de productos de IBM en el sitio web de
IBM http://www.ibm.com/ibm/environment/products/index.shtml.
Notice: This mark applies only to countries within the European Union (EU) and
Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC
concerning waste electrical and electronic equipment (WEEE). The Directive
determines the framework for the return and recycling of used appliances as
applicable throughout the European Union. This label is applied to various products
to indicate that the product is not to be thrown away, but rather reclaimed upon end
of life per this Directive.
Appendix C. Notices
77
Remarque : Cette marque s’applique uniquement aux pays de l’Union Européenne
et à la Norvège.
L’etiquette du système respecte la Directive européenne 2002/96/EC en matière de
Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les
dispositions de retour et de recyclage applicables aux systèmes utilisés à travers
l’Union européenne. Conformément à la directive, ladite étiquette précise que le
produit sur lequel elle est apposée ne doit pas être jeté mais être récupéré en fin
de vie.
In accordance with the European WEEE Directive, electrical and electronic
equipment (EEE) is to be collected separately and to be reused, recycled, or
recovered at end of life. Users of EEE with the WEEE marking per Annex IV of the
WEEE Directive, as shown above, must not dispose of end of life EEE as unsorted
municipal waste, but use the collection framework available to customers for the
return, recycling, and recovery of WEEE. Customer participation is important to
minimize any potential effects of EEE on the environment and human health due to
the potential presence of hazardous substances in EEE. For proper collection and
treatment, contact your local IBM representative.
Battery return program
This product may contain a sealed lead acid, nickel cadmium, nickel metal hydride,
lithium, or lithium ion battery. Consult your user manual or service manual for
specific battery information. The battery must be recycled or disposed of properly.
Recycling facilities may not be available in your area. For information on disposal of
batteries outside the United States, go to http://www.ibm.com/ibm/environment/
products/index.shtml or contact your local waste disposal facility.
In the United States, IBM has established a return process for reuse, recycling, or
proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride,
and battery packs from IBM equipment. For information on proper disposal of these
batteries, contact IBM at 1-800-426-4333. Have the IBM part number listed on the
battery available prior to your call.
For Taiwan: Please recycle batteries.
For the European Union:
78
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Notice: This mark applies only to countries within the European Union (EU).
Batteries or packaging for batteries are labeled in accordance with European
Directive 2006/66/EC concerning batteries and accumulators and waste batteries
and accumulators. The Directive determines the framework for the return and
recycling of used batteries and accumulators as applicable throughout the European
Union. This label is applied to various batteries to indicate that the battery is not to
be thrown away, but rather reclaimed upon end of life per this Directive.
Les batteries ou emballages pour batteries sont étiquetés conformément aux
directives européennes 2006/66/EC, norme relative aux batteries et accumulateurs
en usage et aux batteries et accumulateurs usés. Les directives déterminent la
marche à suivre en vigueur dans l'Union Européenne pour le retour et le recyclage
des batteries et accumulateurs usés. Cette étiquette est appliquée sur diverses
batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôt
récupérée en fin de cycle de vie selon cette norme.
In accordance with the European Directive 2006/66/EC, batteries and accumulators
are labeled to indicate that they are to be collected separately and recycled at end
of life. The label on the battery may also include a chemical symbol for the metal
concerned in the battery (Pb for lead, Hg for mercury, and Cd for cadmium). Users
of batteries and accumulators must not dispose of batteries and accumulators as
unsorted municipal waste, but use the collection framework available to customers
for the return, recycling, and treatment of batteries and accumulators. Customer
participation is important to minimize any potential effects of batteries and
accumulators on the environment and human health due to the potential presence
of hazardous substances. For proper collection and treatment, contact your local
IBM representative.
For California:
Perchlorate material – special handling may apply. See http://www.dtsc.ca.gov/
hazardouswaste/perchlorate/.
The foregoing notice is provided in accordance with California Code of Regulations
Title 22, Division 4.5 Chapter 33. Best Management Practices for Perchlorate
Materials. This product/part may include a lithium manganese dioxide battery which
contains a perchlorate substance.
Appendix C. Notices
79
Electronic emission notices
Federal Communications Commission (FCC) statement
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the
interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to
meet FCC emission limits. IBM is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes or
modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Industry Canada Class A emission compliance statement
This Class A digital apparatus complies with Canadian ICES-003.
Avis de conformité à la réglementation d’Industrie Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Australia and New Zealand Class A statement
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
United Kingdom telecommunications safety requirement
Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for indirect
connection to public telecommunication systems in the United Kingdom.
European Union EMC Directive conformance statement
This product is in conformity with the protection requirements of EU Council
Directive 2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. IBM cannot accept responsibility for any
failure to satisfy the protection requirements resulting from a nonrecommended
modification of the product, including the fitting of non-IBM option cards.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
80
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
55022. The limits for Class A equipment were derived for commercial and industrial
environments to provide reasonable protection against interference with licensed
communication equipment.
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
European Community contact:
IBM Technical Regulations
Pascalstr. 100, Stuttgart, Germany 70569
Telephone: 0049 (0)711 785 1176
Fax: 0049 (0)711 785 1283
E-mail: tjahn@de.ibm.com
Taiwanese Class A warning statement
Chinese Class A warning statement
Japanese Voluntary Control Council for Interference (VCCI) statement
Appendix C. Notices
81
Korean Class A warning statement
82
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Index
A
L
assistance, getting 55
attention notices 3
LED, green 6
load groups, PDU
B
battery return program
8
M
78
monitoring power status
27
C
N
caution statements 3
Class A electronic emission notice 80
components and controls, PDU front 6
Configuration Utility
using to configure PDU 31
connecting the PDU
to a LAN 25
to an environmental monitoring probe
to output devices 26
to the console 25
CRU part numbers 49
notes 3
notes, important 76
notices 75
electronic emission 80
FCC, Class A 80
notices and statements 3
O
option package contents
4
P
D
danger statements 3
documentation CD 1
E
electronic emission Class A notice
environmental monitoring probe
connecting to PDU 26
features 45
installing 46
using 45
F
FCC Class A notice 80
features of PDU 5
G
getting help 55
green LED 6
H
hardware service and support
help, getting 55
I
IBM Support Line 56
important notices 3
installation requirements
26
56
80
parts that come with PDU 4
PDU
connecting an environmental monitoring probe
connecting output devices 26
connecting the console 25
connecting the power cord 13, 17
connecting to a LAN 25
CRU part numbers 49
features 5
front view components and controls 6
installation requirements 3
load groups 8
monitoring power status 27
parts that come with 4
rear view 8
specifications 51
starting Web interface 33
using Configuration Utility 31
using terminal program to configure 28
vertical mounting in rack cabinet 12
power cord, connecting 17
power status, monitoring 27
product recycling and disposal 77
26
R
rack-mounting
vertical 12
recycling and disposal, product 77
requirements, installation 3
RJ-45 console connector 7
routing power cords (vertical rack-mounting)
15
3
© Copyright IBM Corp. 2006, 2007
83
S
setting PDU IP address
using Configuration Utility 32
using Web interface 42
software service and support 56
specifications, PDU 51
statements and notices 3
support, web site 55
T
telephone numbers 56
terminal program, using to configure PDU
trademarks 75
28
U
United States electronic emission Class A notice
United States FCC Class A notice 80
80
W
Web interface
Environment page
changing configuration 35
viewing status 34
History page
viewing history log 43
Network page
changing network configuration 42
starting 33
System page
adding users 38
changing date and time 39
changing event alerts 40
changing superuser name and password 36
viewing power management information 37
web site
publication ordering 55
support 55
support line, telephone numbers 56
84
DPI C13 PDU+, DPI C13 3-phase PDU+, DPI C19 PDU+, and DPI C19 3-phase PDU+: Installation and Maintenance Guide
Part Number: 43V6030
Printed in USA
(1P) P/N: 43V6030
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising