Birchwood Manor Kitty Home

Birchwood Manor Kitty Home
Birchwood Manor Kitty Home™
(House) Made in the USA with imported parts
K&H Manufacturing, LLC
Colorado Springs, CO
www.khmfg.com | (877) 738-5188
Assembly Instructions
Thank you for purchasing the Birchwood Manor Kitty Home™ by K&H Manufacturing.
NOTE: While this house may be used outdoors, like any pet home, rain or snow may get into the door flaps.
The purpose of the door flaps are to help keep warmth in. It is always best to use this or any pet home in
or under an enclosure such as a garage, car port, shed, barn, deck, etc…
Your Birchwood Manor Kitty Home™ comes with a packet of
Phillips-head screws. All you need is a Phillips-head screw driver!
Read all instructions carefully
3
NOTE: LOCKING
CHANNELS on the
different panels will face
the INTERIOR of the house.
These channels ensure an
extremely sturdy house
when fully assembled.
IMPORTANT: If you are going to use the CLEAR DOOR
FLAPS, NOW would be a good time to install them as it is much
easier to get a proper alignment. Simply remove the tape and
stick the door flap above the door. After initial installation, they
can be removed.
4
HOW TO ASSEMBLE:
NOTE: LOCKING
CHANNELS
1
2
Place the end panel
with door cutout
on a flat surface.
Make sure LOCKING
CHANNELS are
facing up.
See Figure a.
Insert side panels
into the channels
of the end panel
as shown, making
sure all LOCKING
CHANNELS align.
See Figure b.
a
b
Slide bottom platform
into LOCKING
CHANNELS and be
sure it seats fully into
each channel. Glossy
side should face the
interior of the house.
See Figure c.
Place 2nd end
panel with door
cutout onto the unit.
Be sure it fully seats
into the LOCKING
CHANNELS.
See Figure d.
5
Using the provided
screws, screw the
end panel through
the pre-drilled
holes onto the
side panels.
See Figure e.
6
Carefully turn unit
over and repeat this
step by screwing on
other end panel.
See Figure e.
c
d
e
OVER
Birchwood Manor Kitty Home™
(House) Made in the USA with imported parts
K&H Manufacturing, LLC
Colorado Springs, CO
www.khmfg.com | (877) 738-5188
Assembly Instructions
7
Place the house
right side up onto
its floor and install
pad into house.
See Figure f.
11
* NOTE: If you
purchased the
HEATED KITTY
HOME, be sure to
feed the cord through
the provided hole
located on the side
of the house.
See Figure f.
8
9
10
Fully seat roof
panel that has the
weather stripping
onto house,
ensuring weather
stripping is at
the peak of
the house.
See Figure g.
f
CORD
* FEED
THROUGH HOLE HERE
12
(Heated Kitty Home Only)
If desired, use
remaining screws
to secure roof
panels through
pre-drilled holes.
See Figure j.
NOTE:
g
While this house may be
used outdoors, like any
pet home, rain or snow
may get into the door
flaps. The purpose of the
door flaps are to help
keep warmth in.
It is always best to
use this or any pet
home in or under an
enclosure such as a
garage, car port,
shed, barn, deck, etc…
Remove
protective tape
from weather
stripping to
expose glue.
See Figure h.
Install 2nd roof
panel, making sure
channels are fully
seated.
Using hands, press
the roof together
at its peak to help
adhere the weather
stripping.
See Figure i.
h
i
j
Birchwood Manor Heated Pad
(Heated Pad) Made in China
K&H Manufacturing, LLC
Colorado Springs, CO
www.khmfg.com | (719) 591-6950
Care & Instructions
Thank you for purchasing K&H Manufacturing’s Birchwood Manor Thermo-Kitty Home™. When used
correctly, the kitty home and its included, heated pad should provide years of hassle-free warmth for your pet.
The Birchwood Manor Thermo-Kitty Home™ and its heated pad are intended for use indoors and outdoors and is
perfect for garages, porches, barns and animal shelters. The heated pad is designed for use with animals only.
WARNING: This is an electrical product. Read all directions and precautions carefully before operating.
Failure to properly follow all directions and instructions may lead to electrical shock or fire which could cause serious bodily injury.
USE INSTRUCTIONS
Read all instructions carefully. This is an electrical product,
pay special care to IMPORTANT SAFEGUARDS.
1
Place heated pad inside the kitty house. Area chosen for
the kitty house should be a sheltered area out of direct rain
or snow.
2
Plug into 110-120 volt AC outlet. Allow one to two hours
for the BIRCHWOOD MANOR HEATED PAD to warm. The
unit will feel slightly warm to the touch. When an animal
lies on it, the pad will reach a maximum temperature of
approximately 104 degrees F. The built in thermostat will
automatically regulate the temperature.
3
4
After initial warm-up, your BIRCHWOOD MANOR
HEATED PAD will feel cooler to the touch. This is the
intension for energy efficiency. When your pet lies on the
pad, it will warm to a cozy pet-pleasing temperature even
in the coldest of weather.
Testing your BIRCHWOOD MANOR HEATED PAD.
Place a blanket, pillow or other insulating object over part
of your BIRCHWOOD MANOR HEATED PAD. After a few
minutes, place your hand under the insulating object to
experience the warmth your pet will enjoy.
5
To store your BIRCHWOOD MANOR HEATED PAD,
unplug, clean, and store pad when not in use.
6
Save these instructions for your use.
Birchwood Manor
Thermo-Kitty
Home™
Heated Pad Included
IMPORTANT SAFEGUARDS
For household Use Only*
*The heated pad is an electrical device and must only be
operated inside an enclosure such as a porch, shed,
barn, dog house, or cat house.
When using electrical appliances, basic safety precautions
should always be followed including the following:
•
•
Read all instructions.
•
•
•
Close supervision is necessary when used by or near children.
•
•
•
•
DO NOT use appliance for anything other than its intended use.
To protect against electrical hazards, DO NOT immerse cord, plug, or appliance
in water or other liquid.
ALWAYS unplug from outlet when not in use.
DO NOT operate any electrical appliance with a damaged cord or plug, or if
the appliance malfunctions or has been damaged in any way. RETURN all
malfunctioning appliances to the factory for examination.
DO NOT PUNCTURE PLASTIC HOUSING FOR ANY REASON.
For use with 110-120 volt AC ONLY.
DO NOT cover your BIRCHWOOD MANOR HEATED PAD with blankets or
materials other than a fleece K&H HEATED PAD COVER. Other coverings may not
allow heat to radiate properly and could cause pad failure.
•
When placing the pad in an enclosed area, be sure pad covers no more
than half of the floor space so your pet has the option of sleeping on or
off the BIRCHWOOD MANOR HEATED PAD.
•
When used outside your home, this unit must be plugged into a properly grounded
electrical outlet rated for outdoor use. If you do not have a properly grounded outlet,
contact a certified electrician to have one installed.
•
Always make sure the cord exits your pet’s enclosure. Keep cord out of shelter.
Care Instructions:
You may clean the plastic housing of the BIRCHWOOD
MANOR HEATED PAD with a damp cloth when unplugged.
The unit may be plugged in when the plug is thoroughly dry.
Machine wash pad cover on gentle cycle in cold water and line dry.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising