aquaspec faucets
AQUASPEC FAUCETS
MODEL – Z81000 SERIES
SINGLE CONTROL FAUCET
TECHNICAL INFORMATION
FLOW: 2.2 GPM [7.6 L] VARIABLE ORIFICE AERATOR*
MAXIMUM PRESSURE: 125 PSI
CARTRIDGE STYLE: CERAMIC DISC MIXING CARTRIDGE WITH TEMPERATURE LIMIT STOP
* OTHER AERATORS AVAILABLE BY REQUEST
INSTALLATION INSTRUCTIONS
1. MOUNT GASKET (ITEM #6) ONTO SHANKS OF FAUCET BODY (ITEM #5).
2. PLACE FAUCET WITH GASKET ON SINK THROUGH PRE-DRILLED MOUNTING HOLES IN SINK.
3. SECURE FAUCET (ITEM #5) TO SINK USING MOUNTING NUTS (ITEM #7A). DO NOT OVER
TIGHTEN.
4. INSTALL HANDLE (ITEM #1A).
4.1. REMOVE COLORED HOT/COLD INDEX (ITEM #1C) FROM HANDLE BY PRESSING OUT FROM
UNDERSIDE OF HANDLE (ITEM #1A).
4.2. LOOSEN SETSCREW (ITEM #1B) USING 3/32” ALLEN WRENCH.
4.3. SLIDE HANDLE ONTO STEM OF CERAMIC MIXING CARTRIDGE (ITEM #4).
4.4. TIGHTEN SETSCREW (ITEM #1B) USING 3/32” ALLEN WRENCH. DO NO OVERTIGHTEN.
4.5. PRESS COLORED HOT/COLD INDEX (ITEM #1C) INTO HANDLE.
5. ATTACH LAVATORY SUPPLIES TO SHANKS WITH RISER NUTS (ITEM #7B).
6. OPTIONAL:
POP-UP DRAIN (-P)
GRID STRAINER DRAIN (-G)
INSTALL POP-UP DRAIN OR GRID STRAINER DRAIN IN SINK OUTLET AND PLUMB WASTE
CONNECTION.
7. TURN SUPPLY WATER ON AND OPERATE FAUCET CHECKING FOR LEAKS.
8. INSTALL AERATOR INTO FAUCET AND HAND TIGHTEN INTO FAUCET SPOUT. IT MAY BE
NECESSARY TO REMOVE AND CLEAN THE AERATOR AT START UP.
MAINTENANCE
1. YOUR ZURN FAUCET HAS A HIGHLY POLISHED NICKEL CHROME PLATED FINISH. CLEAN WITH
SOAP AND WATER OR A MILD CLEANER WHICH IS SAFE FOR CHROME PLATING. DO NOT USE
ACIDS OR TOILET BOWL CLEANER AS THEY WILL DAMAGE THE FINISH.
2. AQUASPEC FAUCETS CONTAIN CERAMIC MIXING CARTRIDGES WHICH REQUIRE NO
MAINTENANCE. TO REMOVE AND REPLACE THE CARTRIDGE:
2.1. REMOVE HOT/COLD INDEX BUTTON (ITEM #1C) BY CAREFULLY PRYING LOOSE FROM
UNDERSIDE OF HANDLE (ITEM #1A).
2.2. LOOSEN SET SCREW (ITEM # 1B) IN HANDLE.
2.3. REMOVE HANDLE FROM CARTRIDGE STEM.
2.4. LOOSEN AND REMOVE CARTRIDGE CAP (ITEM # 2).
2.5. LOOSEN AND REMOVE CARTRIDGE RETAINING NUT (ITEM #3).
2.6. PULL CERAMIC MIXING CARTRIDGE (ITEM #4) BY PULLING ON STEM WHILE WIGGLING
FROM SIDE-TO-SIDE.
2.7. INSTALL NEW CARTRIDGE USING THE ALIGNMENT PINS FOR PROPER ORIENTATION AND
PROPER SEATING IN THE FAUCET BODY.
2.8. REINSTALL HANDLE ASSEMBLY BY REVERSING STEPS 2.1 THROUGH 2.5.
3. TEMPERATURE LIMIT ADJUSTMENT – THE Z81000 FAUCET MAY BE ADJUSTED TO LIMIT THE
MAXIMUM OPERATING TEMPERATURE.
Form # CF1040
PAGE 1 OF 3
C.N. No.
105499
Date:
Rev.
12/20/06
A
3.1. REMOVE CERAMIC MIXING CARTRIDGE (ITEM #4) PER MAINTENANCE INSTRUCTIONS 2.1
THROUGH 2.6 ABOVE.
3.2. REMOVE RED TEMPERATURE LIMIT RING FROM BLUE MIXING CARTRIDGE.
3.3. ROTATE RED TEMPERATURE LIMIT RING CLOCKWISE TO INCREASE MAXIMUM
TEMPERATURE OR COUNTERCLOCKWISE TO DECREASE MAXIMUM TEMPERATURE. RED
TEMPERATURE LIMIT RING IS MARKED WITH ARROWS AND +/- TO INDICATE DIRECTION OF
ROTATION AND EFFECT ON MAXIMUM TEMPERATURE.
3.4. REPLACE RED TEMPERATURE LIMIT RING IN DESIRED ORIENTATION.
3.5. REINSTALL HANDLE ASSEMBLY BY REVERSING STEPS 2.1 THROUGH 2.5.
3.6. TEST MAXIMUM TEMPERATURE FOR ACCEPTABILITY AND REPEAT STEPS 3.1 THROUGH
3.5 IF NECESSARY.
REPAIR PARTS
G66685
G60502
G66686
SINGLE CONTROL HANDLE ASSEMBLY
MOUNTING HARDWARE
CERAMIC MIXING CARTRIDGE
TROUBLE SHOOTING GUIDE
PROBLEM
CAUSE
SOLUTION
FAUCET LEAKS FROM
UNDER FAUCET HANDLE.
ALL SUPPLIES ARE ON.
CARTRIDGE
RETAINING NUT TOO
LOOSE
REMOVE FAUCET
HANDLE. TIGHTEN
CARTRIDGE RETAINING
NUT. DO NOT OVER
TIGHTEN. TIGHTEN UNTIL
NUT IS SNUG
NO WATER COMES OUT
OF FAUCET SPOUT. ALL
SUPPLIES ARE ON.
AERATOR IS CLOGGED.
REMOVE AERATOR. REMOVE
DEBRIS AND REINSTALL
AERATOR.
WATER DEFLECTS AT
AN ANGLE FROM THE
FAUCET SPOUT
AERATOR HAS DEBRIS
REMOVE AERATOR. REMOVE
DEBRIS AND REINSTALL AERATOR.
ZURN INDUSTRIES, INC.
COMMERCIAL BRASS OPERATIONS
2640 SOUTH WORK STREET
FALCONER, N.Y. 14733
PHONE: 1-716-665-1132 FAX: 1-716-665-1135
WORLD WIDE WEB: www.zurn.com
PAGE 2 OF 3
Form # CF1040
C.N. No.
105499
Date:
Rev.
12/20/06
A
Item
1
1A
1B
1C
2
3
4
5
6
7
7A
7B
8
Part Number
G66685
92025001
92024001
92023001
92026001
92027001
G66686
G66687
92041001
G60502
59530002
59532001
G63505
Description
Handle Assembly
Handle
Set Screw
Index
Cartridge Cap
Retaining Nut
Cartridge Assembly
Body Assembly
Gasket
Mounting Hardware
Mounting Nut
1/2" NPSM Riser Nut
13/16"-27 Male Aerator - 2.2 GPM
Qty.
1
1
1
1
1
1
1
1
1
1
2
2
1
Form # CF1040
PAGE 3 OF 3
C.N. No.
105499
Date:
Rev.
12/20/06
A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising