CK60 Vehicle Dock Quick Start Guide
VBUS
PWR
PWR_OUT to power USB peripherals
Shell
C-GND
PWR
Chassis Ground
NC
7
NC
8
NC
P/N 930-006-001
CK60 Vehicle Dock Quick Start Guide
tel
*930-006-001*
www.intermec.com
© 2005 Intermec Technologies
Corporation. All rights reserved.
I
RS-232 Data set ready
7
RTS
O
RS-232 Request to send
4
NC
8
CTS
I
RS-232 Clear to send
9
POWER
PWR
5 volts @ .5 Amps 2.5 Watts
Shell
C-GND
PWR
Chassis Ground
5
GND
Ethernet receive negative
PWR
CK60 Vehicle Dock
425.348.2600
6001 36th Avenue West
Everett, Washington 98203 U.S.A.
Corporate Headquarters
DSR
NC
TXD
O
RS-232 Transmit data
Signal Name
I/O to Computer
Description
4
DTR
O
RS-232 Data terminal ready
1
USBH_D-
I/O
USB Host data negative
5
GND
PWR
Signal Ground
2
USBH_D+
I/O
USB Host data positive
Pin Number
Signal Name
I/O to Computer
Description
1
DCD
I
RS-232 Data carrier detect
2
RXD
I
RS-232 Receive data
Quick Start Guide
Serial RS-232 DB9M Connector Pin Outs
CK60 Vehicle Dock Features
Out of the Box
The Intermec CK60 Vehicle Dock:
•
•
•
•
9
6
6
3
3
Pin Number
USB Host Micro DB9F Connector Pin Outs
Operating Temperature: -20°C to +50°C (-4°F to +122°F)
Storage temperature:
-30°C to 70°C (-22°F to +158°F)
Relative Humidity:
5% to 95%
Environmental Specifications
CK60 Vehicle Dock Features
Release button
provides power and charges the battery pack for the CK60 Handheld Computer.
secures CK60 Handheld Computer in dock while vehicle is in motion.
provides an RS-232 serial connector for serial scanners, printers, and other devices.
USB A Host connection allows connection of peripheral devices such as keyboards to
the CK60 Handheld Computer.
CK60 Handheld Computer
holding bay
Handheld computer retaining
assembly
The CK60 Vehicle Dock shipping box should contain these items:
•
•
•
CK60 Vehicle Dock
CK60 Vehicle Dock Quick Start Guide
Product Warranty Card and Compliance Statement
What You Need
Handheld computer
protection bumpers
To Install and use the CK60 Vehicle Dock, you need:
•
•
•
Intermec cabling kits to connect Vehicle Dock to vehicle power source. Your Intermec
sales team will be able to assist you with kit requirements. The Vehicle Dock may be
used with or without an external power connection. Using without a power cable, the
mobile computer is not charged while docked.
Intermec Vehicle Dock Mounting Kit (p/n: 805-638-001) allows mounting of the vehicle dock in a truck cab or forklift. This mounting kit is specifically selected for use with
the Vehicle Dock and is designed to reduce the amount of vibration transferred to the
mobile computer. Substitution of mounting devices or methods not approved by
Intermect is not recommended.
Data Cables, as required by your application.
Mounting kit attachment
location area
Docking connector
CK60 Vehicle Dock Rear View
CK60 Vehicle Dock Front View
CK60 Vehicle Dock Installation Instructions
CK30 Handheld Computer Quick Start Guide
Installing Your CK60 Vehicle Dock
1
2
3
Install Vehicle Dock and Mounting Kit to your vehicle in a location that is convenient to the operator but does not interfere with vehicle operation or operator
safety. See instructions included with Mounting Kit for details.
Installing Your CK60 into the CK60
Vehicle Dock
Removing Your CK60 from the CK60 Vehicle Dock
1
1
Using your thumb, press the CK60 Handheld Computer release button.
Connect power cable to the power cable connector on the bottom of the Vehicle
Dock. See instructions included with the applicable Power Cable Kit for detail.
Using your thumb, press the CK60 Handheld Computer release button to lift up
the retaining bar.
2
Lift the CK60 Handheld Computer straight up from the connector.
2
Line the CK60 Handheld Computer over the docking connector and push your
CK60 down until it is securely seated on the connector.
3
Position your hand in the middle of the Retaining Bar and push down to secure
the CK60 Handheld Computer. Power is provided to your CK60 Handheld Computer only when the retaining bar is secured.
Connect data cables if applicable.
•
Five (5) volts DC is provided on the RS232 serial connector to power selected
Intermec tethered scanners.
•
The USB Adapter Cable (p/n: 236-051-001) is required to connect a standard
USB-A male cable to the Intermec special connector.
•
This cable is required only if you want to attach a USB device.
Retaining bar must be depressed and engaged to properly secure your
CK60 Handheld Computer before moving your vehicle. Failure to secure
your CK60 Handheld Computer could result in serious injury.
Cable Connectors
Push down in middle to properly secure CK60 in bay
Serial connector
Handheld retaining bar
Vehicle power
source connector
Press with your thumb
to release button
USB micro DB9 connector
CK60 Vehicle Dock Bottom View
Release button
Handheld retaining bar
assembly
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising