Series 9200 - Auto Gate Tech

Series 9200 - Auto Gate Tech
Installation/Owner’s Manual
Series 9200
Heavy-Duty Vehicular Slide Gate Operator
Use this manual for circuit board 4404-010 Revision A or higher.
CA
CO
NF
AN OR
SI/U MS
L-32TO
CE
5
RT
CS IFI
A C2 ED
2.2 TO
NO
CU
. 24
LA
7
R
S
GA
N/
VE
HI
CL
533
82
AS
TE
MO
DE
L
SE
OP
ER
HP
RI
AL
AT
OR
WA
R
9210-065-M-9-14
NI
NG
VO
LT
S
AM
PS
MA
X GA
TE
LO
AD
Do
orKi
ng
, Inc
.,
PH
AS
60
E
Hz
Ing
lew
oo
d,
CA
MO
SE VIN
RIO G
US GAT
Op
era
IN E CA
an te
JU
d fre ga
RY N CA
e ofte on
Do
OR USE
pe ly wh
op
or not allo
le en
DEA
an ga
op
d ob te
era w
TH
te child
str are
Do
ga
uc a is
te. ren
tio in
pa not sta
to
ns sig
th
pla
.
ht
wh nd
y in
ile in
ga
Re
ga ga
te
te te
ad
are
is pa
ow
mo th
a
ne
vin or wa
r’s
g.
ma
lk
nu
thr
al
ou
an
gh
d saf
ety
ins
tru
cti
on
s.
Date Installed:
Installer/Company Name:
Circuit Board
Serial Number
and Revision Letter:
Phone Number:
Leave Manual with Owner
Copyright 2014 DoorKing, Inc. All rights reserved.
UL 325 Compliant
Copyright 2009 DoorKing, Inc. All rights reserved.
Motor
Power
Volt / Phase
Amps
115 / 1
208 / 1
230 / 1
208 / 3
230 / 3
460 / 3
208 / 1
230 / 1
208 / 3
230 / 3
460 / 3
9.7
5.0
4.9
3.3
3.4
1.7
11.5
11.7
6.6
6.2
3.3
208 / 3
9.8
9220
2HP
9230
3HP
9235
1HP
3HP
9240
9210
Model #
SPECIFICATIONS
3HP
230 / 3
9.6
208 / 3
12.8
230 / 3
12.6
208 / 3
9.8
230 / 3
9.6
Chain #
Max Gate
Weight - lbs.
50
2000
60
3000
50
1800
Gear
Reducer
Slow
Down
Gate
Speed
40:1
No
1 ft/sec Fixed
Solid State Relays
No
No
No
Not
Included
40:1
Yes
Up to 2 ft/sec
Adjustable
Speed Control
3 HP
Module
No
No
Not
Included
5 HP
Module
No
Yes
Included
10 HP
Module
Yes
Yes
Included
10 HP
Module
No
Yes
Included
60
2000
60
5000
40:1
Yes
60
3000
10:1
Yes
80
8000
40:1
Yes
Up to 2 ft/sec
Adjustable
Speed Control
Up to 4 ft/sec
Adjustable
Speed Control
Up to 2 ft/sec
Adjustable
Speed Control
AC Module Mechanical
Electronic
Pedestal
Speed Control Speed Brake AC Tech Brake Stand Kit
Class of Operation
Type of Gate
Max Gate Length
Series 9200 - UL 325 Class III, IV
Vehicular Slide Gates Only
100 Ft (Installed Level)
Cycles
Operating Temperature
Continuous
10° F to 140° F (-12° C to 62° C)
“Optional” heater kits recommended for colder temperatures.
Provision for connection of a non-contact sensor (Type B1)
and/or a contact sensor (Type B2).
Entrapment Protection
Heavy-Duty Pedestal
Mounting Stand Kit
18”
20”
2”
16”
16”
WARNING
P/N 9200-135
CONFORMS TO
ANSI/UL-325
53382
CERTIFIED TO
CAN/CSA C22.2 NO. 247
VEHICULAR GATE OPERATOR
CLASS
HP
MODEL
VOLTS
PHASE
AMPS
60 Hz
MAX GATE LOAD
DoorKing, Inc., Inglewood, CA
20”
MOVING GATE CAN CAUSE
SERIOUS INJURY OR DEATH
Operate gate only when gate area is in sight
and free of people and obstructions.
SERIAL
Do not allow children to play in gate area
or operate gate.
Do not stand in gate path or walk through
path while gate is moving.
Read owner’s manual and safety instructions.
18
”
”
12
5”
16
2
31.
.25
”
35.5”
14”
Chain Height:
Idler wheels in
factory set
position.
DoorKing, Inc. reserves the right to make changes in the products described in this manual without notice and without obligation of DoorKing, Inc. to notify any persons
of any such revisions or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to this manual. This manual is copyrighted, all rights
reserved. No portion of this manual may be copied, reproduced, translated, or reduced to any electronic medium without prior written consent from DoorKing, Inc.
9210-065-M-9-14
1
TABLE OF CONTENTS
SPECIFICATIONS
Slide Gate Requirements
4
Safety Information for Slide Gate Operators
5
Gate Construction
6
Important Safety Instructions
6
Instructions regarding intended installation:
6
Important Notices
7
UL325 Entrapment Protection
8
Glossary
9
SECTION 1 - INSTALLATION
10
1.1 Gate Hardware
10
1.2 Underground Conduit Requirements
10
1.3 Installation Options, Gate Types
1.4 Installation #1
1.5 Installation #2, Chain Tray Kit
11-12
13
14-15
1.6 Chain Installation
16
1.7 Installation of Warning Signs
17
SECTION 2 - AC POWER TO OPERATOR(S)
17
2.1 High Voltage Wire Runs
17
2.2 High Voltage Terminal Connection
18
SECTION 3 - ADJUSTMENTS
3.1 Circuit Board Description and Adjustments
3.2 DIP-Switch SW 1 and SW 2 Settings
3.3 Limit Switches
2
1
19
19
20-21
22
9210-065-M-9-14
TABLE OF CONTENTS
3.4 Inherent Reverse Sensor Adjustment
23
3.5 Current Sensor Adjustment
23
3.6 AC Module Adjustment
24
SECTION 4 - ENTRAPMENT AND SAFETY PROTECTION
4.1 UL 325 Terminal Description
4.2 Secondary Entrapment Protection Device Locations
4.3 Loop Detector Wiring
SECTION 5 - MAIN TERMINAL WIRING
25
25
26-27
28
29
5.1 Main Terminal Description
29
5.2 Control Wiring for Single/Primary Operator
30
5.3 Auxiliary Device Wiring
31
5.4 Bi-Parting Gates Wiring - Dual Gate Operators
32
SECTION 6 - OPERATING INSTRUCTIONS
33
6.1 AC Power and Reset Button(s)
33
6.2 Shutdown Conditions
34
Soft Shutdown
Hard Shutdown
6.3 Manual Gate Operation
SECTION 7 - MAINTENANCE AND TROUBLESHOOTING
7.1
Maintenance
7.2 Built-In Diagnostic Tests
36
36
37
7.3 Troubleshooting
37-38
7.4 Accessory Items
39
9200 Wiring Schematics
9210-065-M-9-14
35
40-49
3
Illustrations not to scale.
Slide Gate Requirements
The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate
access opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that
persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.
(ref. UL 325 56.8.4.b)
Adjacent fence that covers open gate position.
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Fence
High Risk of Entrapment Area
Closed Gate
All openings of a horizontal slide gate are guarded or
screened from the bottom of the gate to a minimum
of six (6) feet (1.83 m) above the ground to prevent
a 2 1/4 inch (57.2 mm) diameter sphere from
passing through the openings anywhere in the gate
and in that portion of the adjacent fence that the
gate covers in the open position.
(ref. ASTM F2200-11a, 6.1.2)
XXX
XXX
XXX
XXX
Gate Frame and Adjacent Fence Area
Drawings NOT to scale.
Less than 2 1/4”
Screened Wire Mesh.
Gate Frame and Adjacent Fence Area
4
72” (6 ft) minimum
Non-compliant openings wider than 2 1/4”.
A gap, measured in the horizontal plane parallel to
the roadway, between a fixed stationary object
nearest the roadway (such as a gate support post)
and the gate frame when the gate is in either the
fully open position or the fully closed position, shall
not exceed 2 1/4 inch (57.2 mm).
(ref. ASTM F2200 6.1.4)
Note: Install
screened wire
mesh to an
existing
non-compliant
gate and the
adjacent fence
that covers
open gate
position
(See above).
Note: A filler post or
barrier may need to
be installed in the gap
area to reduce the
distance to 2 1/4
inches or less. A
contact sensor should
be installed in this
area for safety.
(See A on next
page and page 26).
Gate Support Post
XXX
High Risk of Entrapment Area
XXX
2 1/4” maximum gap area
XXX
Gate Frame
XXX
6 ft. minimum
X
Gates shall be designed, constructed and
installed to not fall over more than 45
degrees from the vertical plane, when a gate
is detatched from the supporting hardware.
Rollers
Fall Over Bracket
Compliant openings less than 2 1/4”.
Guide
XXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
9210-065-M-9-14
Safety Information for Slide Gate Operators
Entrapment protection devices are required to reduce the risk of injury.
Install sensors where the risk of entrapment or obstruction exists while
gate is moving. Individual requirements will vary. See pages 25-28 for
more information on typical layout locations and setup.
Physical Stops
Positive stops shall be required
to limit travel to the designed
fully open and fully closed
positions. These stops shall be
installed either at the top of the
gate, or at the bottom of the
gate where such stops shall
horizontally or vertically project
no more than is required to
perform their intended function.
Helps minimize the potential of entrapment during the back
travel of the gate.
2
Contact Sensor (Reversing Edges)
A
Installed on the fence to help minimize the potential of
entrapment between the gate and fence. A filler post or
barrier MAY need to be installed between fence and gate.
B
Helps minimize the potential of entrapment during the
back travel of the gate.
Guide Rollers
Moving Gate Can Cause
Serious Injury or Death
See previous page for more information.
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
A
Minimizes the potential
of the gate closing
when a vehicle is
present. Number and
placement of loops is
dependent on the
application.
Warning Signs
Separate
Pedestrian
Walkway
1
C
Moving Gate Can Cause
Serious Injury or Death
Fence
Permanently mounted and easily
visible from either side of the gate.
1
Reverse
Loop
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
Physical Stop
Minimizes the potential
of the gate closing
when a vehicle is
present. Number and
placement of loops is
dependent on the
application.
Non-Secure Side of Gate
Reverse
Loop
Closed Gate
(Optional) will
provide an open
command to the
gate operator(s)
when a vehicle is
exiting the property.
Secure Side of Gate
Automatic
Exit Loop
May be necessary on part
of fence AND entire gate.
See previous page for more
information.
Warning Sign
B
Minimizes the potential of the gate closing on vehicular
or other traffic that loops cannot sense.
Screened
Wire Mesh
XXX
C
Fence
2
XXXXXXXXX
Minimizes the potential of the gate closing on vehicular or
other traffic that loops cannot sense. It can be installed on the
secure OR non-secure side of gate.
High Risk of Entrapment Area
Non-Contact Sensors (Photo Sensors)
1
Illustration not to scale.
Note: DO NOT USE MMTC,
Inc. Model IR55 Photo
Sensor - P/N 8080-010 for
the 9200 series slide gate
operator.
Located so pedestrians
cannot come in contact
with the vehicular gate.
9210-065-M-9-14
5
ASTM F2200 Standard for Gate Construction
Vehicular gates should be constructed and installed in accordance with ASTM F2200; Standard Specification for Automated
Vehicular Gate Construction. For a copy of this standard, contact ASTM directly at 610-832-9585; service@astm.org; or
www.astm.org.
Important Safety Instructions
WARNING - To reduce the risk of injury or death:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with gate controls. Keep the remote control away from children.
3. Always keep people and objects away from gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
4. Test the operator monthly. The gate MUST reverse on contact with a rigid object or stop or reverse when an object
activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust
and retest the gate operator properly can increase the risk of injury or death.
5. Use the emergency release only when the gate is not moving.
6. KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a qualified service person make repairs to gate
hardware.
7. The entrance is for vehicles only. Pedestrians must use separate entrance.
8. SAVE THESE INSTRUCTIONS!
Instructions regarding intended installation:
• Install the gate operator only if:
1. The operator is appropriate for the construction of the gate and the usage class of the gate.
2. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 6 feet
(1.83 m) above the ground to prevent a 2 ¼ inch (57.2 mm) diameter sphere from passing through the openings
anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open position.
3. All exposed pinch points are eliminated or guarded.
4. Guarding is supplied for exposed rollers.
• The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate
access opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that
persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.
• The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures
when opening and closing to reduce the risk of entrapment. Swinging gates should not open into public access areas.
• The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. Do not
over-tighten the operator clutch, pressure relief valve or reduce reversing sensitivity to compensate for a damaged gate.
• For gate operators utilizing Type D protection:
1. The gate operator controls must be placed so that the user has full view of the gate area when the gate is moving.
2. A warning placard shall be placed adjacent to the controls.
3. An automatic closing device (such as a timer, loop sensor, or similar device) shall not be employed.
4. No other activation device shall be connected.
• Controls intended for user activation must be located at least ten feet (10’) away from any moving part of the gate and
where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or
easily accessible controls should have a security feature to prevent unauthorized use.
• The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset control shall not
cause the operator to start.
• A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.
• For gate operators utilizing a non-contact sensor:
1. See the instructions on the placement of non-contact sensors for each type of application.
2. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate
is still moving in the opening direction.
3. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exist, such as the
perimeter reachable by a moving gate or barrier.
6
9210-065-M-9-14
• For gate operators utilizing contact sensors:
1. One or more contact sensors shall be located where the risk of entrapment or obstruction exist, such as at the
leading edge, trailing edge, and post mounted both inside and outside of a vehicular horizontal slide gate.
2. One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.
3. One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate.
4. A hardwired contact sensor shall be located and its wiring arranged so that the communication between the sensor
and the gate operator is not subjected to mechanical damage.
5. A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for
entrapment protection functions shall be located where the transmission of the signals are not obstructed or
impeded by building structures, natural landscaping or similar obstructions. A wireless contact sensor shall function
under the intended end-use conditions.
6. One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm).
Important Notices
Vehicular gate operator products provide convenience and security. However, gate operators must use high levels of force
to move gates and most people underestimate the power of these systems and do not realize the potential hazards associated with an incorrectly designed or installed system. These hazards may include:
• Pinch points
• Entrapment areas
• Reach through hazards
• Absence of entrapment protection devices
• Improperly located access controls
• Absence of vehicle protection devices
• Absence of controlled pedestrian access
In addition to these potential hazards, automated vehicular gate systems must be installed in accordance with the UL 325
Safety Standard and the ASTM F2200 Construction Standard. Most lay persons are unaware of, or are not familiar with,
these standards. If an automated vehicular gate system is not properly designed, installed, used and maintained, serious
injuries or death can result. Be sure that the installer has instructed you on the proper operation of the gate and gate
operator system.
Be sure that the installer has trained you about the basic functions of the required reversing systems associated with your
gate operating system and how to test them. These include reversing loops, inherent reversing system, electric edges,
photoelectric cells, or other external devices.
• This Owner’s Manual is your property. Keep it in a safe place for future reference.
• Be sure that all access control devices are installed a minimum distance of 10 feet away from the gate and gate
operator, or in such a way that a person cannot touch the gate or gate operator while using the device. If access
control devices are installed in violation of these restrictions, immediately remove the gate operator from service
and contact your installing dealer.
• Loops and loop detectors, photo-cells or other equivalent devices must be installed to prevent the gate from
closing on vehicular traffic.
• The speed limit for vehicular traffic through the gate area is 5 MPH. Install speed bumps and signs to keep
vehicular traffic from speeding through the gate area. Failure to adhere to posted speed limits can result in
damage to the gate, gate operator, and to the vehicle.
• Be sure that all persons who will use the gate system are familiar with the proper use of the gate and gate
operator and are familiar with the possible hazards associated with the gate system.
• Be sure that warning signs are permanently installed on both sides of the gate in an area where they are fully
visible to traffic.
• It is your responsibility to periodically check all entrapment protection devices. If any of these devices are
observed to function improperly, remove the operator from service immediately and contact your installing or
servicing dealer.
• Follow the recommended maintenance schedule.
• Do not allow children to play in the area of the operator or to play with any gate-operating device.
• To remove the gate operator from service, operate the gate to the full open position and then shut off power to
the operator at the service panel.
9210-065-M-9-14
7
UL325 Entrapment Protection
Class I
Class II
A vehicular gate operator (or system) intended for use in a
home of one-to four single family dwelling, or a garage or
parking area associated therewith.
A vehicular gate operator (or system) intended for use in a
commercial location or building such as a multi-family
housing unit (five or more single family units) hotel,
garages, retail store or other building servicing the general
public.
STATE PRISON
Class III
Class IV
A vehicular gate operator (or system) intended for use in a
industrial location or building such as a factory or loading
dock area or other locations not intended to service the
general public.
A vehicular gate operator (or system) intended for use in a
guarded industrial location or building such as an airport
security area or other restricted access locations not
servicing the general public, in which unauthorized access
is prevented via supervision by security personnel.
This table illustrates the entrapment protection requirements for each of the four UL325 classes.
UL325
Classifications
Horizontal Slide, Vertical Lift, Vertical Pivot
Secondary Protection
Primary Protection
A
B1, B2 or D
A or C
A, B1, B2, C or D
Class III
A, B1 or B2
A, B1, B2, D or E
A, B1, B2 or C
A, B1, B2, C or D
Class IV
A, B1, B2 or D
A, B1, B2, D or E
A, B1, B2, C or D
A, B1, B2, C, D or E
Class I and II
Primary Protection
Swing and Vertical Barrier (arm)
Secondary Protection
A - Inherent entrapment protection system.
B1 - Provision for connection of, or supplied with, a non-contact sensor (photoelectric sensor or the equivalent).
When used as the PRIMARY device, must be monitored.
B2 - Provision for connection of, or supplied with, a contact sensor (edge device or the equivalent).
When used as the PRIMARY device, must be monitored.
C - Inherent adjustable clutch or pressure relief device.
D - Provision for connection of, or supplied with, an actuating device requiring continuous pressure to maintain
opening or closing motion of the gate.
E - An inherent audio alarm.
8
9210-065-M-9-14
Glossary
GATE - A moving barrier such as a swinging, sliding, raising, lowering, or the like, barrier, that is a stand-alone passage
barrier or is that portion of a wall or fence system that controls entrance and/or egress by persons or vehicles and
completes the perimeter of a defined area.
RESIDENTIAL VEHICULAR GATE OPERATOR – CLASS I - A vehicular gate operator (or system) intended for use in a home
of one-to four single family dwelling, or garage or parking area associated therewith.
COMMERCIAL / GENERAL ACCESS VEHICULAR GATE OPERATOR - CLASS II - A vehicular gate operator (or system)
intended for use in a commercial location or building such as a multi-family housing unit (five or more single family units),
hotels, garages, retail store, or other building servicing the general public.
INDUSTRIAL / LIMITED ACCESS VEHICULAR GATE OPERATOR - CLASS III - A vehicular gate operator (or system)
intended for use in an industrial location or building such as a factory or loading dock area or other locations not intended
to service the general public.
RESTRICTED ACCESS VEHICULAR GATE OPERATOR - CLASS IV - A vehicular gate operator (or system) intended for use in
a guarded industrial location or building such as an airport security area or other restricted access locations not servicing
the general public, in which unauthorized access is prevented via supervision by security personnel.
VEHICULAR BARRIER (ARM) OPERATOR (OR SYSTEM) - An operator (or system) that controls a cantilever type device (or
system), consisting of a mechanical arm or barrier that moves in a vertical arc, intended for vehicular traffic flow at
entrances or exits to areas such as parking garages, lots or toll areas.
VEHICULAR HORIZONTAL SLIDE-GATE OPERATOR (OR SYSTEM) - A vehicular gate operator (or system) that controls a
gate which slides in a horizontal direction that is intended for use for vehicular entrance and exit to a drive, parking lot, or
the like.
VEHICULAR SWING-GATE OPERATOR (OR SYSTEM) - A vehicular gate operator (or system) that controls a gate which
moves in an arc in a horizontal plane that is intended for use for vehicular entrance and exit to a drive, parking lot, or the
like.
SYSTEM - In the context of these requirements, a system refers to a group of interacting devices intended to perform a
common function.
WIRED CONTROL - A control implemented in a form of fixed physical interconnections between the control, the associated
devices, and an operator to perform predetermined functions in response to input signals.
WIRELESS CONTROL - A control implemented in means other than fixed physical interconnections (such as radio waves or
infrared beams) between the control, the associated devices, and an operator to perform predetermined functions in
response to input signals.
INHERENT ENTRAPMENT PROTECTION SYSTEM - A system, examples being a motor current or speed sensing system,
which provides protection against entrapment upon sensing an object and is incorporated as a permanent and integral part
of the operator.
EXTERNAL ENTRAPMENT PROTECTION DEVICE - A device, examples being an edge sensor, a photoelectric sensor, or
similar entrapment protection device, which provides protection against entrapment when activated and is not incorporated
as a permanent part of an operator.
ENTRAPMENT - The condition when an object is caught or held in a position that increases the risk of injury.
9210-065-M-9-14
9
SECTION 1 - INSTALLATION
Prior to beginning the installation of the slide gate operator, we suggest that you become familiar with the
instructions, illustrations, and wiring guide-lines in this manual. This will help insure that your installation is
performed in an efficient and professional manner compliant with UL 325 safety and ASTM F2200 construction
standards.
The proper installation of the vehicular slide gate operator is an extremely important and integral part of the
overall access control system. Check all local building ordinances and building codes prior to installing this
operator. Be sure your installation is in compliance with local codes.
1.1 Gate Hardware
6 Inch
4 Inch
DoorKing has a full line of Tandem V-wheels that are ideal for heavy gates and
will ensure safe, reliable and long lasting gate operation. The gate must be
properly installed and roll smoothly in both directions.
Guide Rollers with Protective Covers
Helps to minimize a pinch point on the
gate.
1.2 Underground Conduit Requirements
Secondary
Operator
Position
Primary/Secondary Interconnection Cable (Dual Operator Application Only)
Control and/or P.A.M.S. Wires (Low Voltage wire insulation)
Loop Lead-In Wires (Low Voltage wire insulation)
AC Input Power (High Voltage wire insulation)
AC Input Power (High Voltage wire insulation)
Sweeps
3/4 Inch Minimum
Concrete Pad
Concrete Pad
Single/
Primary
Operator
Position
• The conduit requirements are for a typical slide gate operator installation (the secondary operator is shown for
those applications where a secondary operator may be used). The conduit requirements for your application may
vary from this depending on your specific needs.
• Use only sweeps for conduit bends. Do not use 90° elbows as this will make wire pulls very difficult and can cause
damage to wire insulation.
Sweep
• DoorKing recommends using 3/4-inch conduit.
YES
Elbow
• Be sure that all conduits are installed in accordance with local codes.
NO
• Never run low voltage rated wire insulation in the same conduit as high voltage rated wire insulation.
10
9210-065-M-9-14
1.3 Installation Options
The operator MUST be level. See the next page for typical gate types. We suggest that you contact the local building department to determine the required depth of the concrete pad since soil conditions and code requirements vary from city to city.
#1 - Operator Mounted Directly on a Concrete Pad
Typically used when gates are less than 20 feet in length and under 2000 lbs. in weight. V-rail v-wheel gate type shown.
Chain
Configuration
CONF
ANSIORM
/UL-3S TO
CAN/ CERT
25
CSA IFIED
VEHI C22.2 TO
CULA NO.
53382
CLAS
247
R
S
GATE
MOD
OPER
EL
ATOR
SERI
HP
AL
VOLT
S
AMPS
MAX
PHAS
GATE
DoorK
LOAD
ing,
E
60
Hz
Inc.,
Ingle
wood
, CA
WAR
See page
16 for
details.
NI
NG
MOV
SER ING
IOUS
GAT
Opera
INJUE CAN
and te
freegate
RY CAU
of only
OR
Do
peoplewhen
DEASE
or not allow
and gate
opera
TH
area
obstru
te childr
Do
gate.
is
ctionsin sight
en
pathnot stand
to
play
.
while
in
in
gate
Read
gate gate
area
is path
owner
movin
or
’s
g. walk
manu
throug
al
and
h
safety
instru
ctions
.
Idler
Wheels
See page 13 for details.
Co
ncr
ete
Pa
d
Idler wheels are factory set in the correct position.
Remove the chain knock-outs in operator housing.
#2 - Operator Mounted on the Heavy-Duty Pedestal Mounting Stand
The pedestal mounting stand kit (P/N 9200-135) MUST be used when gates require a chain tray (Typically for gates that are
longer than 20 feet in length). The chain tray helps support the weight of the chain and reduce the chain stretching that occurs
over time. DoorKing offers a chain tray kit that will fit any length gate (P/N 2601-270 10 ft. connecting sections).
DoorKing highly recommends using the pedestal stand for gates heavier than 2000 lbs. for a more secure attachment to a larger
and heavier concrete pad. V-rail v-wheel gate type shown.
CONF
ORMS
ANSI/
UL-32TO
CAN/CCERT
5
SA IFIED
VEHI C22.2 TO
CULA NO.
53382
CLAS
247
R
S
GATE
MODE
OPER
L
ATOR
SERIA
HP
L
VOLT
S
WAR
NI
NG
AMPS
MAX
GATE
LOAD
DoorK
ing,
Inc.,
PHAS
E
60
Hz
Inglew
ood,
CA
MOV
SER ING
IOUS
Chain
Configuration
GAT
Opera
INJUE CAN
and te
free gate
RY CAU
of only
Do
OR
people when
or not allow
DEASE
and gate
operat
TH
childre obstruarea
e gate.
Do
is
ctions
n to
in
pathnot stand
sight
play
.
while
in
in
gate
Read
gate gate
area
is path
owner
movin
or
’s
manua g. walk
throug
l and
h
safety
instruc
tions.
See page
16 for
details.
See pages 14 and 15 for details.
ain
al
est g
Peduntin
Motand
S
y
Tra
Ch
Co
ncr
ete
Idler
Wheels
Pa
d
The idler wheels must be moved to the lower position to
use a chain tray. DO NOT remove the chain knock-outs.
9210-065-M-9-14
11
1.3 Continued
Gate Types
• Steel or Aluminum.
• 8,000 lb Max. Weight
per Gate (9240).
He
-D
y
v
a
u
rn
O
ty
e
am
n
C
tal
an
v
tile
so
ate
ed
nd
me
g
for
om
c
and
d
tan
s
ting
n
y
tra
rec
oun
CONFORMS
ANSI/UL-325
TO
CLASS
NO.
G
OPERATOR
HP
VOLTS
GATE
LOAD
DoorKing,
MOVING
SERIOUS
PHASE
60
Operate
and
free
Hz
Inc.,
Inglewood,
CA
B
ut y
o
ra
xF
GATE
INJURY
CAN
gate
of
people
CAUSE
only
Do
OR
when
and
or not allow
DEATH
operate
obstructions.
gate
children
area
Do
gate.
is in
pathnot stand
to
sight
play
while
in gate
in gate
Read
gate
owner’s is moving.
path
area
or
walk
manual
through
and
safety
instructions.
m
lm
sta
e
53382
247
GATE
SERIAL
Ped
WARNIN
C22.2 TO
VEHICULAR
MODEL
AMPS
MAX
He
er
hai
CAN/CSA
CERTIFIED
-D
y
v
a
a
eC
n
v
tile
WARNIN
C22.2 TO
VEHICULAR
CLASS
53382
NO.
247
MODEL
GATE
SERIAL
HP
G
OPERATOR
VOLTS
AMPS
MAX
PHASE
GATE
DoorKing,LOAD 60
Hz
Inc.,
Inglewood,
MOVING
SERIOUS
Operate
and
free
CA
GATE
INJURY
CAN
gate
of
people
only
Do
CAUSE
when
and OR
or not allow
operate
obstructions.
gate DEATH
children
area
Do
gate.
is in
pathnot stand
to
sight
play
while
in gate
in gate
Read
gate
owner’s is moving.
path
area
or
walk
manual
through
and
safety
instructions.
er
es
l
sta
e
Ped
and
e
end
ec
yr
tra
un
mo
d
ty
-Du
B
F
ox
ra
CONFORMS
ANSI/UL-325
CAN/CSA
CERTIFIED TO
C22.2
VEHICULARNO.
TO
CLASS
247 53382
GATE
MODEL
OPERATOR
SERIAL
HP
VOLTS
AMPS
MAX
PHASE
GATE
DoorKing,LOAD60
Hz
Inc.,
Inglewood,
nd
da
ing
tal
t
oun
n
sta
eco
m
H
D
vya
e
cha
V
ut y
-R
V
ail
g
for
s
e
mm
yr
ra
in t
es
Ped
th h
eng engt
L
ate ate L
x. G tal G
a
Ft Max. To
0
0
M
1
r - 00 Ft
o
t
era - 2
Op tors
e
l
g
ra
Sin l Ope
a
Du
12
nde
er
oll
vy
o
m
om
nd
sta
2
ver
o
df
in
cha
at
rg
ate
R
me
t.
0f
ting
CONFORMS
ANSI/UL-325
CAN/CSA
CERTIFIED TO
a
He
t.
0f
2
ver
-
e
Wh
e
na
r
O
l
r
ove
m
20
ft.
ta
en
l
WARNING
MOVING
SERIOUS
and
Operate GATE
free INJURY
CAN
gate
of
people
Do
only ORCAUSE
or not
when
and DEATH
operate
allow
Do
gate
children obstructions.
CA pathnot gate.
area
stand
while
is in
to
Read
in gate play
sight
gate
in gate
owner’s is
path
moving.
manual or walk area
through
and
safety
instructions.
CONFORMS
ANSI/UL-325
CAN/CSA
CERTIFIED
TO
WAR
C22.2 TO
VEHICULAR
CLASS
NO.
NING
53382
247
GATE
MODEL
OPERATOR
SERIAL
HP
VOLTS
AMPS
MAX
GATE
LOAD
DoorKing,
MOVING
SERIOUS
PHASE
60
GATE
Hz
Inc.,
Inglewood,
CA
Operate
INJURY
and
CAN
free gate
CAUSE
of only
Do
people when
OR
or not allow
DEATH
and gate
operate
area
children obstructions.
Do
gate.
is
in
pathnot stand
to
sight
play
while
in
in
gate
Read
gate gate
area
path
owner’s is moving.
or
walk
manual
through
and
safety
instructions.
in
chat.
d
n
f
d a 20
tan over
s
ing es
unt r gat
o
m fo
tal ded
s
e
n
Ped mme
th h
o
eng engt
L
rec
L
e
at ate
x. G tal G
a
Ft M . To
00 t Max
1
F
rato - 200
r
e
Op rs
gle erato
n
i
S l Op
a
Du
y
tra
9210-065-M-9-14
The operator is heavy. Two persons are required
when handling the operator during installation.
1.4 Installation #1
Operator Mounted Directly
on a Concrete Pad
Tip: Trace the base plate of the operator on a
piece of masonite (Not provided) and make a
template to help locate where the conduit runs
will be positioned in the concrete pad.
Ele
CO
NFO
AN RM
SI/U S
L-3 TO
CAN CER
25
/CS TIF
A C22IED
VE
.2 TO
HIC
NO
. 247
CLA ULAR
SS
GA
TE
MO
OP
DEL
SER
5338
2
ctr
IN
ER
AT
OR
HP
IAL
WA
RN
G
VO
LTS
AM
PS
MA
X GAT
E LOA
Doo
D
rKin
g,
Inc
.,
PH
ASE
60
Hz
Ing
lew
ood
, CA
oni
cB
MO
SE VING
RI
OU GA
Ope
S IN TE
and rate
JU CAN
free gate
RY CA
of only
Do
OR US
peo whe
ple
or not allo
DE E
andn gate
ope
AT
rate w chil
obs area
H
truc is
Do
gate dren
pathnot stan
whi
ox
tion in
to
s. sigh
play
t
d
in
le in gate
gate
Rea
gate
d own
area
is path
mov
er’s
ing.or wal
man
k thro
ual
ugh
and
safe
ty
inst
ruct
ions
.
.
1
18
te
pla d
m
e
e
T
ite ovid
son ot Pr
a
M N
Limit Assembly Guard
”
20”
2
3
Gain Access Inside
Operator
Caution: DO NOT lay the operator on it’s
side or oil will leak out of the gear reducer.
Remove the limit assembly guard.
Remove the 3 locknuts inside the
electronic box to swing box open.
Gate
1”
1”
Important: Operator
6.75”
MUST be parallel to gate!
Base Plate
11.75” 10.75”
Conduit
Area
Conduit
Area
Conduit
Area
1/2
DO NOT set anchor bolts in
wet concrete. Sleeve anchors
should be used after concrete
has cured for greater
flexibility in positioning the
operator on the pad.
23”
7.5”
11.25”
12”
16”
16.75”
20.5”
4”
4”
Concrete Pad
To attach operator to
concrete pad DoorKing
recommends twelve (12)
1/2” x 3” sleeve anchors
(not supplied).
28”
Conduit suggestions:
• High voltage conduit
• Low voltage access control device conduit
• Automatic exit loop conduit
• Reverse loop conduit
Concrete pad
MUST be level!
Pad depth is determined by
soil conditions and local
building codes. Minimum
depth is 18 inches.
Reinforced concrete
recommended.
9210-065-M-9-14
Concrete Pad
4” Minimum Above Ground
Wire Mesh
Conduit
13
1.5 Installation #2
Operator Mounted on the Heavy-Duty
Pedestal Mounting Stand
The operator is heavy. Two persons are required when handling
the operator during installation.
Caution: DO NOT lay the operator on it’s side or oil will leak out
of the gear reducer.
1. Assemble and install the pedestal mounting stand kit (P/N
9200-135) on the concrete pad, then mount the operator to it.
Follow the instructions that came with the pedestal mounting
stand kit for assembly of the stand.
2. Move the idler wheels to the lower operating position in the
operator AFTER the operator has been installed on the pedestal
mounting stand. See the previous page’s instructions to gain
access inside the operator.
3. Install chain tray kit on the gate (See next page for details).
Gate
1”
1.75”
4”
Important: Pedestal
mounting stand MUST
be parallel to gate!
1/2
4”
11.625”
DO NOT set anchor bolts
in wet concrete. Sleeve
anchors should be used
after concrete has cured
for greater flexibility in
positioning the pedestal
stand on the pad.
Conduit
11.75” Area
15.75”
6.25”
Reinforced concrete
recommended.
14
11.625”
4”
Concrete Pad
39”
Pedestal mounting
stand MUST be level!
Pad depth is determined
by soil conditions and
local building codes.
Minimum depth is 18
inches.
4”
Concrete Pad
22”
To attach pedestal
stand to concrete
pad DoorKing
recommends
sixteen (16)
1/2” x 3” sleeve
anchors
(not supplied).
Conduit suggestions:
• High voltage conduit
• Low voltage access control device conduit
• Automatic exit loop conduit
• Reverse loop conduit
4” Minimum Above Ground
Wire Mesh
Conduit
9210-065-M-9-14
1.5 Continued - Chain Tray Kit
Installing the Chain Tray Kit
A chain tray is recommended for gates longer than 20 ft. to support the weight of the chain. DoorKing offers a
chain tray kit in sections to fit any length gate. (DoorKing P/N 2601-270 10 Ft. section)
Chain Tray
Supporting
Bracket
(Facing up)
Ft.
Carriage Bolts
Se
gm
ent
Weep Hole
Chain Tray
Segments
Connection
10
Ft.
Se
gm
ent
Chain Tray
Supporting
Bracket
(Facing down)
Gate
10
1”
Tip: Chain tray supporting brackets can be
mounted facing down (as shown on right),
facing up or extended depending on the
chain height and position. For further
information, refer to instructions provided
with the chain tray kit.
Note: The chain should sag at least
one (1) inch per 10 feet of travel.
10.5”
Note: All gate types can
have the chain tray
installed on them, V-rail
v-wheel ornamental is
shown here.
Chain Tray
Supporting
Bracket
4” Minimum Pad
Ground
9210-065-M-9-14
15
1.6 Chain Installation
1 Operator MUST be parallel to gate!
Note: Be sure to follow all 3 guidelines. Installing the chain in any
other manner will cause excessive noise, chain idler wheel wear
and chain stretching.
2 Chain brackets MUST align with
3 Chain brackets MUST be mounted
idler wheels so chain stays parallel
to gate!
so the chain remains the same
height as it is on the idler wheels!
Directly on a Concrete Pad - #1 Factory Set Idler Wheels
Gate
2
2
Chain
Bracket
Chain
Bracket
Idler Wheels
Chain
Configuration
1
3
3
Idler
Wheels
14”
14”
Ground
4” Min.
14”
14”
Concrete Pad
Heavy-Duty Pedestal Mounting Stand - #2 Lower Idler Wheel Position
Gate
2
2
Chain
Bracket
Chain
Bracket
Idler Wheels
Chain
Configuration
1
Gate
Frame
Chain Bracket
Chain Bracket
on
ti
Op
1
n
tio
Op
Chain
Nut
Chain
Bolt
2
r
ste
k
Lin
Idler
Wheels
3
Connect Chain Bracket
to Gate. Weld completely
around bracket. Chain nut
and chain bolt should not
protrude past gate frame.
10.5”
10.5”
3
10.5”
10.5”
Ma
Ground
4” Min.
Concrete Pad
Connect Chain to Chain Bracket. Connect chain to chain bolt
with master link. Adjust the chain nuts to tighten the chain. The
chain should sag no more than one (1) inch per 10 feet of travel.
Do not over tighten the chain.
16
9210-065-M-9-14
1.7 Installation of Warning Signs
This DoorKing Slide Gate Operator is shipped with two warning signs. The purpose of the
warning sign is to alert uninformed persons, and to remind persons familiar with the gate
system, that a possible hazard exists so that appropriate action can be taken to avoid the
hazard or to reduce exposure to the hazard. See page 5 for typical placement of signs.
• Permanently install the supplied warning signs in locations so
that the signs are visible by persons on both sides of the gate.
• Use appropriate hardware such as wood or sheet metal screws
(not supplied) to install the warning signs.
SECTION 2 - AC POWER TO OPERATOR(S)
Before attempting to connect any wiring to the operator, be sure that the circuit breaker in the electrical panel is in the OFF position. Permanent wiring must be installed to the operator as required by local electrical codes. It is recommended that a licensed electrical contractor
perform this work.
Since building codes vary from city to city, we highly recommend that you check with your local building department prior to installing
any permanent wiring to be sure that all wiring to the operator (both high and low voltage) complies with local code requirements.
THIS GATE OPERATOR MUST BE PROPERLY GROUNDED!!
Typical
Grounding
Sources
Electrical
Panel
Ground to existing
electrical system.
Ground to metallic
cold water pipe.
Ground
Wire
Grounding rod
10 feet in soil.
Ground
Wire
IMPORTANT: Ground wire shown without safety protection for clarity. Make sure ground
wire is protected from being touched or electrical shock could occur!
2.1 High Voltage Wire Runs
The 9200 draws significant power and each operator should have a “Dedicated” circuit breaker at the power source. If power wiring is
greater than the maximum distance shown, it is recommended that a service feeder be installed. When large gauge wire is used, a separate
junction box must be installed for the operator connection. The wire table is based on stranded copper wire. Wire run calculations are based
on the NEC recommended maximum 3% voltage drop on the power line, plus an additional 10% reduction in distance to allow for other losses
in the system.
This table illustrates the high voltage AC power wire size and distance limitations for a single operator.
Never run low voltage rated wire insulation in the
same conduit as high voltage rated wire insulation.
Single Phase
Three Phase
9210 Single 1 HP: 115 VAC
9210 Single 1 HP: 208 VAC
9210 Single 1 HP: 230 VAC
9220 Single 2 HP: 208 VAC
9220 Single 2 HP: 230 VAC
9210 Single 1 HP: 208 VAC
9210 Single 1 HP: 230 VAC
9210 Single 1 HP: 460 VAC
9220 Single 2 HP: 208 VAC
9220 Single 2 HP: 230 VAC
9220 Single 2 HP: 460 VAC
9230, 9240 Single 3 HP: 208 VAC
9230, 9240 Single 3 HP: 230 VAC
9235 Single 3 HP: 208 VAC
9235 Single 3 HP: 230 VAC
Wire Size / Max Distance in Feet
Amps
12 AWG
10 AWG
8 AWG
6 AWG
9.7
5.0
4.9
11.5
11.7
3.3
3.4
1.7
6.6
6.2
3.3
9.8
9.6
12.8
12.6
110
390
440
165
180
680
730
2900
340
400
1500
225
255
177
195
175
620
700
270
290
1090
1170
4600
545
640
2400
365
415
280
315
295
1040
1170
450
490
1815
1950
7800
905
1070
4000
610
690
465
525
440
1560
1760
675
735
2720
2920
11700
1360
1605
6000
915
1035
700
790
“Optional” Heater Installation Note: When installing a heater, refer to the “high voltage AC power wire size
and distance limitations” table on the instruction sheet with the heater kit for AC power wire run limitations.
9210-065-M-9-14
17
2.2 High Voltage Terminal Connection
• Route incoming AC power wire through the high voltage conduit and run wire in the operator electronic box as shown.
• Be sure wiring is installed in accordance with local codes. Be sure to color code all wiring.
• It is recommended that a surge suppressor be installed on the high voltage power lines to help protect the operator
and circuit board from surges and power fluctuations.
Dual Operators
• Dual operators (Primary/Secondary) require AC power to EACH operator.
AC Power
AC Power
RESET
AC
POWER
Hot
DO NOT power up and cycle the operator until the
OFF
Neu
“DIP-Switches” and the “Limit Switches” have been
adjusted. Damage could occur to the gate and operator.
115 VAC Output
115
VAC
SINGLE Phase
Chassis
Ground
DANGER
High Voltage
AC Input Wire
White - Neutral
Black - 115 VAC Hot
Green - Chassis Ground
HIGH VOLTAGE!
CO
NF
AN OR
SI/ MS
UL TO
-32
CA CE
5
N/ RT
CS IFI
A C2 ED
VE
2.2 TO
HI
NO
CU
. 24
CL
LA
AS
7
R
S
MO
GA
TE
DE
L
SE
RI
AL
VO
LT
S
AM
MA
533
OP
ER
HP
AT
X GA
TE
LO
AD
Do
orK
ing
, Inc
.,
PH
AS
E
60
Hz
Ing
lew
oo
d,
WA
R
82
OR
PS
CA
NI
High
Voltage
AC Input
Wire
NG
Hot
Hot
115 VAC Output
MOV
SE IN
RI G GA
OU
Op
S IN TE
era
and te
JU CAN
fre gate
RY CA
e of on
Do
OR US
peo ly wh
ple en
or not allo
DE E
and gat
op
AT
era w
ob e are
te chi
H
str
Do
gat ldr
uct a is
e. en
ion in sig
pat not sta
to
s.
h wh nd
pla
ht
y in
ile in
gat
gat gat
ad
e are
e is e pat
ow
mo h
a
ner
vin or wa
’s
g.
ma
lk
nu
thr
al
ou
and
gh
saf
ety
ins
tru
ctio
ns.
Re
Chassis
Ground
1
Electronic Box
CAUTION
High Voltage AC input power
MUST MATCH the operator
specifications or DAMAGE will
occur and VOID the warranty!
SINGLE Phase
High Voltage
AC Input Wire
2
Hot
Hot
Hot
115 VAC Output
3
Remove the 3
locknuts inside
the electronic
box to swing
box open.
High Voltage
Conduit
Keep wire clear of all moving parts.
18
208/230 VAC
Chassis
Ground
208/230
VAC
THREE Phase
High Voltage
AC Input Wire
Check polarity of
three phase motor.
See page 22.
External Power Disconnect Switch
A separate power disconnect switch
may be needed in your area. Check
local building codes before installation.
Recommended by DoorKing.
9210-065-M-9-14
SECTION 3 - ADJUSTMENTS
The switch settings and adjustments in this chapter should be made after your installation and wiring to the operator(s) is
complete. Whenever any of the programming switches on the circuit board are changed, power must be shut-off, and then
turned back on for the new setting to take effect.
3.1 Circuit Board Description and Adjustments
LEDs Indicates that low voltage power is applied to the circuit board. Input LEDs should be OFF and will only
illuminate when the input is activated (seep age 29). Limit LEDs will be on when the respective limit switch is
activated.
Single Channel Loop Detector Dual Channel Loop Detector
AC Module Dual
See page 28.
See page 32.
Adjustment
AC Module
Adjustment
9235 models with
mechanical disc brake.
9220, 9230, 9235,
and 9240 models
9409
1495-010
P2
9410
HIGH SPEED
ADJUST
1 ft/s
1.5 ft/s
Limit Switch Plug P2
See page 28
See page 22
See page 22
LMT
1 2 3 4
ON
SW 1 is Upside-Down on Board
Self-Test
1 2 3 4
1 2 3 4 5 6 7 8
ON
ON
Self-test (when turned on)
SW 2, switch 1.
1 2 3 4
P7
ON
NC
SW 2 is Upside-Down on Board
Main Terminal
8 Input
7 LEDs
6 5See 4page329 2 1
Inherent
Reverse
Sensors
OPEN
NO
Dry Relay Contact
NC
Dry relay contacts
(terminals 11-12) can be
set for Normally Open
(NO) or Normally Closed
(NC) operation by placing
the relay shorting bar on the
N.O. or N.C. pins respectively.
SW 1, switches 4 and 5 must
be set to control relay. See
SW 1 is Upside-Down on Board
next 2 pages for descriptions.
ON
Max
Sensitivity
1 2 3 4 5 6 7 8
CLOSE
Min
CAUTION
Do not run self-test with the
operator connected to the gate.
The drive chain MUST be
disconnected before running the
self-test. This feature is designed
for bench testing ONLY.
Auto-Close Timer
Auto-close timer (when
turned on) SW 1, switch 2.
ON
NO
UL 325 Terminal See page 25
20 19 18 17 16 15 14 13 12 11 10 9
9210-065-M-9-14
ON
SW 2 is Upside-Down on Board
TIME
DELAY
REV SENSE
CLOSE
See page 23
P6
Motor
Plug P6
Sensor Input LEDs
4404-010
4404-010
REV SENSE
OPEN
9235 model ONLY
DIP-Switches
Set the DIP-switches on the circuit
board to the desired setting. See
switch descriptions on next 2 pages.
P8
Mechanical
Disc Brake
Plug P8
Exit Loop Port See page 28 See page 24.
EXIT
LOOP
Power LED
LMT
LOOP
REVERSE
See page 24.
Limit LEDs
Reverse Loop Port
Min Max
Speed
Adjust reversing
sensitivity for
open and close
directions.
Full counter
clockwise for
minimum
sensitivity, full
clockwise for
maximum
sensitivity.
See page 23.
SLOW SPEED
ADJUST
P1
2 ft/s
1 2 3 4 5 6 7 8
0 ft/s
1 2 3 4 5 6 7 8
.5 ft/s
SW 1 is Upside-Down on Board
Adjust from 1 second
(full counter-clockwise) to
approximately 23 seconds
(full clockwise).
1
23
19
3.2 DIP-Switch SW 1 and SW 2 Settings
The two DIP-switches located on the circuit board are used to program the operator to operate in various modes and to turn on
or off various operating features. Whenever a switch setting is changed, power to the operator must be turned OFF and then
turned back on for the new setting to take affect. Check and review ALL switch settings prior to applying power to the operator.
1 2 3 4
Typical
Settings
SW 1 - Right 8 Switches
ON
ON
SW 2 is Upside-Down on Circuit Board.
1 2 3 4 5 6 7 8
Left 4 Switches - SW 2
SW 1 is Upside-Down on Circuit Board.
SW 1 - Right 8 Switches
Switch
1
Function
Setting
Changes the direction
the operator will
open/close the gate.
Description
Opening direction
using OFF setting.
Opening direction
using ON setting.
Opening direction
using ON setting.
Factory Set Configuration
2
3
Auto-Close
Timer
Exit Loop Port
Output
Full Open Input
Jumper
Wire
Needed
Opening direction
using OFF setting.
Lower Configuration
OFF Auto-close timer is OFF. Manual input required to close gate.
ON Auto-close timer is ON. Adjustable from 1-23 seconds to close gate.
OFF The output wired to terminal #4 becomes the output from the loop detector
installed in the EXIT loop port. Plug-in loop detector required for “OFF” function.
ON Normal Setting. Terminal #4 is a normal full open input for a single gate operator.
Relay Activation 4-OFF 5-OFF Relay activates and LED is ON when the gate is fully open.
and
4-OFF 5-ON Relay activates and LED is ON when the gate is not closed.
4 and 5
LED Indicator 4-ON 5-OFF Relay activates and LED is ON when the gate is opening and open.
Light Activation
4-ON 5-ON Relay activates and LED is ON when the gate is opening and closing.
6
Warn Before
Operate
7
Reverses Gate
Stops Gate
8
Quick-Close
Timer Override
OFF Normal Setting. No sound.
ON Internal alarm will sound before gate starts and throughout gate’s cycle.
OFF Normal Setting. Input to terminal #6 and/or reverse loops will REVERSE gate
during CLOSE cycle.
ON Input to terminal #6 and/or reverse loops will STOP gate during CLOSE cycle.
OFF Normal Setting. Timer will function normally.
ON Opening gate will stop and begin to close as soon as all reversing inputs (Reverse
loops, photo sensors) are cleared regardless of the distance the gate has opened.
SW 2 - Left 4 Switches
20
Switch
Function
1
Self-Test
2
Gate Opens
Uphill
3
Gate Opens
Downhill
4
Spare
Setting
Description
OFF
ON
OFF
ON
OFF
ON
Normal Setting. Normal gate operation.
Self-test mode. Operator MUST be disconnected from gate to run self-test.
Normal Setting. Normal gate operation.
MUST be ON if gate opens UPHILL.
Normal Setting. Normal gate operation.
MUST be ON if gate opens DOWNHILL.
OFF Leave in the OFF position.
9210-065-M-9-14
3.2 Continued
The two DIP-switches located on the circuit board (Upside-Down ) are used to program the operator to operate in various
modes and to turn on or off various operating features. Whenever a switch setting is changed, power to the operator must be
turned OFF and then turned back on for the new setting to take affect. Check and review ALL switch settings prior to applying
power to the operator.
Switch Definitions
Typical Settings
1 2 3 4 5 6 7 8
SW 1 - Right 8 Switches
SW 1 is Upside-Down on Circuit Board.
ON
Switch 1 Motor direction switch - Must OPEN the gate upon initial AC power up and open command. If the open command
begins to close the gate, turn AC power off and reverse this switch.
Switch 2 Turns the auto-close timer on or off. Can be adjusted from 1 to 23 seconds to close gate.
Switch 3 A device wired to terminal #4 (Switch 3 ON) is a normal full open input. The output wired to terminal #4 (Switch 3
OFF) becomes the output of a plug-in loop detector that is installed in the EXIT loop port of the circuit board (Which must be
installed for the “OFF” setting to function). A jumper wire is needed to open and close gate(s). Terminal #4 jumpered to #5 is
used for partially opening an automatic exit loop using a single channel plug-in loop detector for a single gate operator (Page
28) OR terminal #4 jumpered to #2 will fully open bi-parting gates using a dual channel plug-in loop detector (Page 32).
Switches 4-5 These work in conjunction with each other and determine when the relay on the board will be activated. This relay
can be used as a switch for various functions such as illuminating a warning light when the gate is moving, or turning on a
green light when the gate is full open. If a magnetic lock is used with the gate operator, these switches must be set for magnetic
lock operation which limits the relay to activate only when the gate is opening and full open.
Switch 6 Warn Before Operate, When set to the ON position, the internal alarm in the operator will start sounding 2-3 seconds
prior to the gate starting and continue throughout the gate’s cycle.
Switch 7 Determines if an input to terminal #6 (Photo Sensors) AND/OR reverse loops will reverse OR stop a CLOSING gate.
A tailgating vehicle can activate terminal #6 (Photo sensors) and/or reverse loops while the gate is in the closing cycle from the
previous vehicle’s authorized entry:
If switch 7 is turned OFF (Reverse), the closing gate that gets activated by a tailgating vehicle will reverse back to the open
position, possibly allowing the tailgating vehicle unauthorized entry while the gate is reversing back to the open position.
If switch 7 is turned ON (Stop), the closing gate that gets activated by a tailgating vehicle will stop, partially or completely
blocking the pathway, NOT allowing the tailgating vehicle to enter without proper authorization. The gate will not move until all
sensors are clear, usually forcing the tailgating vehicle that activated the sensors to back away from the gate. The gate will then
continue until closed, helping prevent the tailgating vehicle from unauthorized entry.
Switch 8 Turning the quick-close feature on will cause the auto close timer to close the gate after 1 second, regardless of the
setting of the auto close timer potentiometer. This will also cause an opening gate to stop and reverse when the reverse loops
and/or photo sensors are cleared. This feature, along with turning switch 7 ON above, is useful to help prevent tailgating
vehicles from unauthorized entry.
Typical Settings
1 2 3 4
SW 2 - Left 4 Switches
SW 2 is Upside-Down on Circuit Board.
ON
Switch 1 This switch is a self-test feature that checks various functions of the circuit board and is used for bench test only.
Do not run this test with the operator connected to the gate.
Switch 2 Set to the OFF position for normal operation. Set to the ON position if gate OPENS in an UPHILL direction.
Switch 3 Set to the OFF position for normal operation. Set to the ON position if gate OPENS in an DOWNHILL direction.
Switch 4 Spare switch, leave in the OFF position.
9210-065-M-9-14
21
Check the polarity of “Three Phase” operator ONLY: Position the gate half
way open. Give open command and while gate is opening, activate the
appropriate limit switch with your finger. Gate should STOP. If it does not,
activate the other limit switch. If this STOPS the gate, AC power wires must
be changed (Reverse the connection of any 2 wires and re-check limits).
3.3 Limit Switches
Adjust Limit Nuts
Important: Turn power OFF and set AC module (On select
models) to maximum speed before adjusting limit nuts!
1
Push and hold the lock plate down where shown to adjust the
Open and Close limit nuts.
2
After adjusting the limit nuts, be sure that the lock-plate is
engaged in the slots on the limit nuts to prevent them from
rotating.
3
On select 9200 models, the slow-down limit assembly will
move up or down 3/4 inch. DO NOT remove the slow-down
limit assembly from the 3/4 inch slot and re-attach it in the
partial open adjustment rail to gain further adjustment. This
will cause mechanical damage to the switch assembly
when the operator is activated.
4
5
Turn power on and activate the gate operator.
A
A
Push
Slow-Down Limit
A1
Lock-Plate
Partial Open Adjustment Rail
Slow-Down
Limit
(3/4 inch
adjustment
ONLY)
A1
Limit Nut
Limit
Switch
Re-adjust the limit nuts as necessary for full-open and
full-close gate travel. After you are satisified with the gate
limit settings, the AC module (On select models) can then be
adjusted to personal preference (See page 24).
Partial Open Feature: When using the
Middle Limit Nut
partial open feature, the operator’s access
Magnet - Align with pick-up sensor control device must be connected to terminal
#5 . Adjust the middle limit nut and
B Magnetic Pick-Up Sensor
magnetic pick-up sensor assembly to the
gate’s desired stopping position. Be sure to
align the magnet (Recessed in the limit nut)
with the magnetic pick-up sensor.
B
Push
Partial Open
Magnetic
Pick-up
Sensor
Adjustment
Limit LEDs
A1
A
LMT
LMT
T
C1
C
4404-010
1 2 3 4 5 6 7 8
ON
TIME
DELAY
1 2 3 4
ON
P6
REV SENSE
CLOSE
Limit
Switch
REV SENSE
OPEN
C
EXIT
LOOP
LMT
MT
T
LOOP
REVERSE
C
P8
C1
B
Limit Nut
C
A
Limit Nut
Slow-Down
Limit
(3/4 inch
adjustment
ONLY)
Slow-Down Limit
C1
P7
NO
Note: If limit
plug is not
connected to
the circuit
board and
AC power is
turned on,
alarm will
sound and
operator will
NOT
function.
NC
CAUTION
Power MUST be OFF to operator
BEFORE adjusting limit nuts or
injury could occur!
22
Main Terminal Partial Open Connection
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4 3
2 1
9210-065-M-9-14
3.4 Inherent Reverse Sensors Adjustment
This vehicular gate operator is equipped with an inherent adjustable reversing sensor (Type A) used as the primary entrapment
protection system according to UL 325 standards. The gate will reverse direction after “physically” encountering an
obstruction in either the opening or closing gate cycle.
If the Auto-Close Timer (DIP-switch SW 1, switch 2) is ON and the gate physically encounters an obstruction during the
CLOSING cycle, it will reverse to the open position and HOLD the gate at this position (Soft shutdown condition). Another input
command is needed before the gate will reset and close again.
If the Partial Open Feature is being used and the gate physically encounters an obstruction during the CLOSING cycle, the gate
will only reverse to the FULL open limit switch setting and NOT the partial open setting.
For the reverse system to function correctly, the gate must be properly installed and work freely in both directions and the limit
switches must be properly adjusted before adjusting these sensors. The ideal adjustment will allow the operator to move the
gate through its entire travel cycle without reversing, but will reverse upon contact with an obstruction with no more than 40
Min
Lbs of force. This force can be measured with a gate scale, P/N 2600-225.
1 Momentarily jumper a wire across terminals 1 and 4 to OPEN the gate.
Max
2 After opening gate reaches full speed, slowly rotate the OPEN reverse sensor clockwise until the LED Sensitivity
5 Cycle the gate a few times to be sure that it cycles completely. The current sensor may
need to be adjusted if gate will not reverse properly (See 3.5 below)
Test the operator reversing sensitivity:
Reverse Sensors
LED lights up and the gate reverses direction. Rotate the CLOSE reverse sensor back counterclockwise approximately 1/8 turn to decrease the sensitivity (LED will turn off). The gate will assume
a soft shutdown so momentarily jumper a wire across terminals 1 and 4 to cycle the operator.
LED
CLOSE
3 Momentarily jumper a wire across terminals 1 and 4 to CLOSE the gate.
4 After closing gate reaches full speed, slowly rotate the CLOSE reverse sensor clockwise until the
OPEN
lights up and gate reverses direction. Rotate the OPEN reverse sensor back counter-clockwise
approximately 1/8 turn to decrease the sensitivity (LED will turn off). The gate will assume a soft
shutdown so momentarily jumper a wire across terminals 1 and 4 to cycle the operator.
LED
Note: Each operator must be
individually adjusted if dual
operators have been installed.
Place an immobile object along the gate path, allowing the gate to strike it while in the open and close cycles. The gate must
reverse direction after striking the object. If it does not, increase the OPEN and CLOSE reverse sensitivity (steps 2 and 4 )
and repeat this testing until the correct sensitivity has been achieved in BOTH directions. The operator will assume a soft
shutdown after striking and reversing the gate which will require a momentary jumper wire across terminals 1 and 4 to cycle
the operator again.
3.5 Current Sensor Adjustment
This vehicular gate operator uses a current sensing device to detect any obstructions in the path of the opening or closing gate.
The current sensor uses a sensing coil with a given number of turns through it to monitor the current flow into the operator.
Each time the wire passes through the coil, it is considered a turn. The number of turns through the sensing coil is dependant
on the operating voltage of the operator, the speed of the gate and the weight of the gate.
In general, light weight gates may require additional turns of wire through the current sensor, while heavier gates may require
less turns. In addition, the speed of the gate can affect how the current sensor works. Gates running at a higher speed may
require less turns of wire through the sensor. CAUTION – HIGH VOLTAGE: Be sure power is turned OFF before changing the
number of wire turns to the current sensor. If you are setting the reverse sensors (section 3.4 above) and reach the full sensitive
position without activating the reversing function, add an additional turn of wire through the current sensor. If you are decreasing the sensitivity and the gate will not run properly, reduce the number of turns through the current sensor.
Sample
Turns
Voltage and Phase Turns
1
1 Turn
9210-065-M-9-14
2
2 Turns
5
5 Turns
6
6 Turns
115 Single Phase
208 Single Phase
230 Single Phase
208 Three Phase
230 Three Phase
1
2
2
5
6
23
3.6 AC Module Adjustment
The 9220, 9230, 9235 and 9240 models are equipped with an AC module that allows you to adjust the speed of the gate from 0
to 2 feet per second. To adjust the speed, simply rotate the speed control knob clockwise to increase the gate speed, or
counter-clockwise to decrease the gate speed. The digital readout on the AC module will display the gate speed.
L1 L2 L3
L1 L2/N
B- B+
B- B+
L1
PE
Min Max
Speed
1.5 ft/s
.5 ft/s
.5 ft/s
1.5 ft/s
Mode
Mode
2 ft/s
0 ft/s
SCM series
SCM series
basic I/O control
1
2
5
6
11
13A
13B
13E
25
17
16
basic I/O control
1
2
5
6
11
13A
13B
13E
25
2 ft/s
SCF series
basic I/O control
Min Max
Speed
1
2
5
6
11
12
2
14
13A
13B
13C
15
25
2
30
31
TXA
TXB
0 ft/s
17
2 ft/s
L3
2. 0
EPM
1 ft/s
1.5 ft/s
Mode
0 ft/s
L2
Min Max
Speed
1. 6
EPM
1 ft/s
16
.5 ft/s
1. 0
EPM
1 ft/s
Min Max
Speed
2 ft/s
1 ft/s
3 ft/s
T1
T2
T3
U
V
W
9235 Models with AC Module Dual Adjustment and Mechanical Disc Brake
U
V
W
U
PE PE
V
W
PE PE
B-
B+
There are 2 speed
adjustments
on the
The high speed
adjust
(Emergency
designed to
3 HP AC
Module that must be adjusted
5 HP
AC 9235.
Module
10 Close)
HP AC is
Module
0 ft/s
4 ft/s
close an open gate as quick as possible. All secondary entrapment protection
devices
and
reversing
sensors
9235 Only
WILL NOT WORK during the high speed closing operation! The slow speed adjust is for normal gate operation.
The 9235 models are equipped with a mechanical disc brake. It is automatically controlled by the AC module and needs NO
adjustment. Note: There is a manual release lock on the disc brake that must be unlocked before the gate can be manually
operated (See section 6.3 manual gate operation on page 35 for further information).
DANGER
AC Module
Dual Adjustment
Gate WILL NOT stop after the Emergency
Close is activated until gate is closed!
Min Max
Speed
Emergency Close Adjustment: Adjust the high speed
from 0 to 6 feet per second. Closing device must be
connected to P2 terminal on 1495 circuit board.
HIGH SPEED
ADJUST
Y
ENC
RG
EME
L3
2. 0
EPM
SE
CLO
Stand-Alone
Push-Button
Normal Gate Adjustment: Adjust the slow speed from
0 to 4 feet per second. Opening device must be connected
to 4404 main circuit board (See page 30).
Mode
P1
SLOW SPEED
ADJUST
To adjust the speed, rotate each speed control potentiometer clockwise to increase
the gate speed, or counter-clockwise to decrease the gate speed. The digital
readout on the AC module will display EITHER high speed OR slow speed, which
ever open/close device has been activated.
24
L2
SCF series
basic I/O control
1
2
5
6
11
12
2
14
13A
13B
13C
15
25
2
30
31
TXA
TXB
Important: Closing device must be far enough from
the gate so that the user is prevented from coming in
contact with the gate while operating the device.
Outdoor or easily accessible closing device should
have a security feature to prevent unauthorized use.
L1
1495-010
P2
T1
T2
T3
U
V
W
B-
B+
10 HP AC Module
9210-065-M-9-14
SECTION 4 - ENTRAPMENT AND SAFETY PROTECTION
Secondary Entrapment Protection Devices:
In addition to the inherent reversing sensor system, the 9200 Series has a 6-pin UL 325 terminal for the connection of photo sensors-Type B1
and reversing edges-Type B2 secondary entrapment protection devices required by UL 325 standards. Entrapment protection devices must
be installed to reduce the risk of injury. Install these devices where the risk of entrapment or obstruction exists while the gate is moving.
The 9200 Series offers numerous options to meet your specific needs. The next 2 pages show wiring and typical positioning of the entrapment
protection devices but specific installations will vary.
Note: Secondary entrapment protection devices will open the gate to the “Partial Open” setting when the opening device is connected to main
terminal #5 (See page 30 for opening device wiring information).
115 VAC
Convenience
Outlets
4.1 UL 325 Terminal Description
EXIT
LOOP
LMT
LOOP
REVERSE
6-Pin UL 325 Terminal
2
1
2
LMT
Secondary Entrapment Protection
Device Connection
1
1
3
4
2
3
4
3
4
EXIT
LOOP
LMT
LOOP
REV SENSE
CLOSE
P8
Note: The 6-pin terminal
can be unplugged from
circuit board for easy
wire connections.
REVERSE
-010
4404
P6
All inputs are normally
open (NO).
P7
1 2 3 4
1 2 3 4 5 6 7 8
ON
ON
1 OPEN Entrapment Sensor (Photo Sensor): Obstructed
opening-direction photo beam will stop the gate during the
opening-direction only. Gate will resume the open cycle
when the obstructed photo beam has been cleared.
OPEN Entrapment Sensor
2 1
CLOSE Entrapment Sensor
NC
6 5 4 3
OPEN Contact Sensor
NO
7
CLOSE Contact Sensor
P7
8
Low Voltage Common
TIME
DELAY
REV SENSE
CLOSE
P6
20 19 18 17 16 15 14 13 12 11 10 9
Low Voltage Common
REV SENSE
OPEN
4404-010
Electronic Box
P8
6 5 4 3 2 1
Wall / Fence
Closed Gate
Opening-Direction Photo Beam
Entrapment Area
Entrapment Area
2 CLOSE Entrapment Sensor (Photo Sensor): Obstructed
closing-direction photo beam will stop the gate during the
closing-direction only. Gate will resume the close cycle
when the obstructed photo beam has been cleared.
Closing-Direction Photo Beam
Wall / Fence
Closed Gate
3 OPEN Contact Sensor (Reversing Edge(s)): Obstructed opening-direction reversing edge(s) will stop, then reverse the gate to the close position during the
opening-direction only.
Wall / Fence
Filler Post if necessary
• After the gate reverses to the full close position, any
Closed Gate
opening input will cycle the gate again. Note: If the gate is
Opening-Direction Reversing Edges
opening by a time clock and an opening-direction reversing
Gate Support Post if Installed
Entrapment Area
edge gets obstructed, the gate will return to the closed
position and another input (automatic exit loop, reverse loop. etc.) is needed to cycle the gate open
again.
• When the opening-direction reversing edge(s) gets obstructed and the gate is traveling back to the close position and
the closing-direction reversing edge gets obstructed, the gate will stop and enter a soft shutdown condition (See page 34).
position, during the
4 CLOSE Contact Sensor (Reversing Edge): Obstructed closing-direction reversing edge will stop, then reverse the gate to the open
Entrapment Area
closing-direction only.
Closing-Direction Reverse Edge
Wall / Fence
• After the gate reverses to the open position, the timer will
Closed Gate
automatically close the gate (if it is turned on). If the
closing-direction reverse edge is activated a second time prior to the gate reaching the
close position, the operator will stop and enter a soft shutdown condition (See page 34).
• When the closing-direction reversing edge gets obstructed and the gate is traveling back to the open
position and the opening-direction revering edge gets obstructed, the gate will stop and enter a soft shutdown condition (See page 34).
5&6
Low Voltage Common: Common terminals for all the secondary entrapment protection device inputs.
9210-065-M-9-14
25
4.2 Secondary Entrapment Protection Device Locations
Typical UL Photo Sensor mounting height
and distance away from gate.
Secure Side
5”
or
Less
5”
or
Less
Inside Property
If the distance between the gate
and wall is greater than 2 1/4”.
Filler Post or Barrier
Non-Secure Side
Outside Property
Reversing Edge (Open Contact Sensor)
Gate Frame
UL sensor mounted on wall.
UL sensor mounted on post.
Gate Frame
Note: Additional
photo sensors can
be added above
the 27.5” height.
Wall
No higher than
27.5” above grade.
21” is typical for
most installations.
Photo sensors may be installed on either side of gate frame, as close as
practical to the gate but no further away than 5”.
A filler post or barrier may need to be installed between the
gate and wall area to reduce the distance to 2 1/4” or less.
A reversing edge should be installed on the post or barrier
for safety (See page 4 for more information).
Photo Sensors (With Filler Post and Reverse Edge) Sample Setup
Closing-Direction Photo Beam
Wall
Filler Post with Opening-Direction Reversing Edge (If necessary, see above)
Closed Gate
LMT
Closing-direction photo sensors wired to UL 325 terminal.
LMT
OPEN Entrapment Sensor
P8
1 2 3 4 5 6 7 8
ON
TIME
DELAY
1 2 3 4
ON
REV SENSE
CLOSE
P7
NO
NC
6 5 4 3 2 1
20 19 18 17 16 15 14 13 12 11 10 9
Normally Open
Normally Open
IF the closing-direction photo sensor is wired to the UL 325 terminal, a
closing-direction photo beam that gets obstructed will STOP the gate, then
resume closing the gate when the obstructed photo beam has been cleared.
Photo Sensor Power Note: Photo sensors can be powered by the built-in
convenience outlets located on the operator (See previous page).
7
6 5 4 3
2 1
Common
ON
Common
Common
8
Normally Open
1 2 3 4 5 6 7 8
Normally Open
Common
26
REV SENSE
OPEN
“Reverse” Closing-Direction Option
4404-101
P6
CLOSE Entrapment Sensor
CLOSE Contact Sensor
OPEN Contact Sensor
Low Voltage Common
Low Voltage Common
6-Pin
UL 325
Terminal
Wiring
EXIT
LOOP
LOOP
REVERSE
Opening-Direction Photo Beam
SW 1, switch 7
MUST be OFF.
SW 1 is Upside-Down on Board
IF the closing-direction photo sensor is wired to the #6 main
terminal, a closing-direction photo beam that gets
obstructed will REVERSE the gate back to the open position.
9210-065-M-9-14
Wireless Reverse Edge Sample Setup - Single Receiver
Edge
Transmitter
Normally Open
Filler Post Note: Install reversing edges on all
the gate support posts or filler post in this area
(e.g. cantilever gate installations, See below).
9 V battery operated transmitter mounted on gate.
Normally Open
Common
OPEN Entrapment Sensor
Filler Post
(If necessary)
Opening-Direction
Reversing Edge
Opening-Direction Reversing Edge (If filler post is used).
Closed Gate
1
2
3
4
5
6
Antenna mounted
outside operator cover.
LMT
6-Pin UL 325
Terminal Wiring
ClosingDirection
Reversing
Edge
EXIT
LOOP
LMT
LOOP
REVERSE
CLOSE Entrapment Sensor
OPEN Contact Sensor
CLOSE Contact Sensor
Low Voltage Common
Low Voltage Common
Wall
Normally Open
P8
REV SENSE
OPEN
Normally Open
1 2 3 4
1 2 3 4 5 6 7 8
ON
TIME
DELAY
REV SENSE
CLOSE
P6
Common
Common
ON
Install
Jumper Wire
4404-101
When either direction reversing edge get obstructed,
the gate will STOP and reverse direction.
Coax Antenna Kit
P/N 1514-073
24 VAC Receiver
Place receiver in operator.
P7
NO
NC
Wireless Note: Refer to the
instruction sheet that comes
with the receiver/transmitter
for more specific wiring and
mounting instructions.
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4 3
20-Pin
Main
Terminal
2 1
To #1 Com
To #3 24 Volt - Power is limited to 250 mamps.
Photo Sensor and Wireless Reverse Edge Sample Setup
reverse edges on the gate
support post(s) in this area.
Cantilever Gate
ClosingDirection
Reversing
Edge
EXIT
LOOP
LMT
LOOP
REVERSE
Photo Sensor Power Note: Photo sensors can be powered by the built-in convenience
outlets located on the operator (See page 25).
Install Opening-Direction
LMT
P8
Opening-Direction Photo Beam
1 2 3 4
Normally Open
1 2 3 4 5 6 7 8
TIME
DELAY
REV SENSE
CLOSE
P6
9 V battery operated transmitter mounted on gate.
Edge
Transmitter
ON
ON
P7
NO
NC
CLOSE Entrapment Sensor
OPEN Entrapment Sensor
OPEN Contact Sensor
Low Voltage Common
Low Voltage Common
CLOSE Contact Sensor
REV SENSE
OPEN
4404-101
6-Pin
20 19 18 17 16 15 14 13 12 11 10 9
6 5 4 3 2 1 UL 325
8
7
6 5 4 3
2 1
Terminal
Wiring
Normally Open
Common
To #3 24 Volt - Power is limited to 250 mamps.
To #1 Com
Common
20-Pin
Main
Terminal
Antenna mounted
outside operator
cover.
When a reversing edge gets obstructed, the
Coax Antenna Kit
gate will STOP and reverse direction. When
P/N 1514-073
24
VAC
Receiver
a photo beam gets obstructed the gate will
Normally Open
STOP, then continue in the same direction
Place receiver in operator.
Common
after obstructed photo beam has been
cleared until the gate cycle is complete.
Wireless Note: Refer to the instruction sheet that comes with the receiver/transmitter for more specific wiring and mounting instructions.
9210-065-M-9-14
27
4.3 Loop Detector Wiring
To help protect the operator from accidentally closing on vehicles in the gate’s path, DoorKing highly recommends that loops
and loop detectors be installed. Loops are laid underneath, cut into asphalt or concrete driveways or buried beneath gravel and
earth driveways. A loop detection system will sense a vehicle like a metal detector and send a signal to the gate operator
preventing the gate from automatically opening or closing on a vehicle when it is in the gate’s path. DoorKing recommends that
a licensed installer perform this work.
DoorKing offers a free “Loop and Loop-Detectors
Information Manual” PDF located at DoorKing’s
web site for more information. www.dkaccess.com
CONFO
ANSI/U
RMS
CAN/CS
CERTIF
A
TO
L-325
WA
RN
IN
G
IED
VEHIC C22.2 TO
NO.
CLASS ULAR
247
53382
GATE
MODEL
OPERA
SERIAL
TOR
HP
VOLTS
AMPS
MAX
PHASE
GATE
DoorKin
LOAD
g,
60
Hz
Inc.,
Inglewo
od,
CA
MOVI
SERIONG
GATE
Operate US
INJURCAN
and
free gate
Y ORCAUS
of only
Do
people when
or not allow
DEATE
and gate
operate
area
children obstructi
H
Do
gate.
is
ons.in sight
pathnot stand
to
play
while
in
in
gate
Read
gate gate
area
path
owner’s is moving.
or
walk
manual
through
and
safety
instructio
ns.
Reverse Loops
Reverse loops are placed on each side of the gate to
prevent the gate from closing on a vehicle in the gate’s
path. They will stop or reverse the cycling of the gate
while a vehicle is in or near the gate’s pathway.
p
PVC Conduit
In
W
ire
s
Note: SW 1, switch 7 must
be set for the reverse loops.
See page 21 for more
information about SW 1,
switch 7 ON/OFF options.
ad
Le
A
ire
op
In
W
Lo
DoorKing
Plug-in
Loop Detectors
Le
ad
ON
Reverse loop
lead-in wires are
twisted approx.
6 twists per foot
and are wired in
series.
1 2 3 4 5 6 7 8
LOOP 1
A
Loo
ate e.
id g renc
o
v
e
f
a
to ter
Re
ate e.
in. ent in
M
id g renc
o
t. em
v
e
F
f
a
4 ov
to ter
m
p
in. ent in
M
.
Loo
t. m
e
nce
s
4 F ove
e
r
d
r
i
e
e
m
v
avo terf
Re
. to op in
n
xit
i
o
cE
i
t. Mrse l
t
F
4 eve
ma op
r
uto Lo
se
ver
Lo
op
SW 1 is Upside-Down on Board
Single Channel
A
9410
1 2 3 4 5 6 7 8
1 2 3 4
ON
1 2 3 4 5 6 7 8
ON
LOOP 1
Exit Loop Port
LMT
TIME
DELAY
4404
NC
1 2 3 4 5 6 7 8
ON
28
NO
SW 1 is Upside-Down on Board
P7
Note: The plug-in exit loop detector can be
wired to partially open the gate if SW 1,
switch 3 is turned OFF. A jumper wire must
be connected from terminal #4 to terminal
#5 (See next page for more information).
REV SENSE
CLOSE
P6
SW 1 is Upside-Down on Board
REV SENSE
OPEN
4404-010
4404-010
LMT
P8
Exit loop lead-in
wires are twisted
approx. 6 twists
per foot.
SW 1, switch 3
must be ON to
FULLY open gate
(Normal function).
Reverse Loop Port
B
LOOP
REVERSE
PVC Conduit
9410
EXIT
LOOP
Automatically opens the gate for exiting
vehicles without having to use a transmitter or
keypad. The exit loop can be placed a
minimum of 4 feet away from the reverse loop
or far enough away from the gate so the gate
has started opening or even completely opened
by the time you drive up to it (Free exit).
Single Channel
B
ON
Automatic Exit Loop
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4 3
Note: Loop detector
wiring is shown for
DoorKing plug-in
loop detector P/N
9410-010 (Single
Channel). If other
loop detectors are
used, refer to the
installation
instructions
supplied with those
detectors for wiring
and separate power
instructions.
2 1
Exit Loop Partial Open
9210-065-M-9-14
SECTION 5 - MAIN TERMINAL WIRING
P7
NO
Auxiliary Common
Terminal
4404
Connect any low
voltage common wire
to these 2 terminals.
Used in conjunction with the
circuit board inherent
reversing sensors. See page
23 for further information.
Low Voltage Common
2 1
Full Open
24 VAC - 250 mamp. max.
Full Open
Partial Open
Standard Reverse OR Stop
3-Button Full Open
6 5 4 3
(DoorKing 3-Button Station ONLY)
3-Button Close
(DoorKing 3-Button Station ONLY)
Gate Tracker - Data
Gate Tracker - Busy
Dry Relay Contact
Dry Relay Contact
Low Voltage Common
Entrapment Alarm
Alarm Reset
Current Sensor
Current Sensor
Motor Hot
Motor Neutral
16
17
7
• SW 1, switch 3 is ON, terminal #4 functions as a normal FULL
open input. (Normal Setting). Single operator use ONLY.
• SW 1, switch 3 is OFF, input to terminal #4
becomes the output from a plug-in loop
detector installed in the EXIT loop port of the
circuit board. A jumper wire is needed to open
and close the gate(s) for these applications:
4
ON
DANGER
HIGH VOLTAGE!
8
1 2 3 4 5 6 7 8
Earth Ground
20 19 18 17 16 15 14 13 12 11 10 9
Low Voltage Common
NC
#2
Main Terminal Input LEDs #10
#9 #8
#7 #6 #5 #4
#2 - Jumper Wire - SW 1, switch 3 OFF (Dual Operators Full Open)
#1 - Jumper Wire - SW 1, switch 3 OFF (Single Operator Exit Loop Partial Open)
Low Voltage Common
5.1 Main Terminal Description
SW 1 is Upside-Down on Board
#1 Terminal #4 jumpered to terminal #5 will PARTIALLY open an
automatic exit loop using a single channel plug-in loop detector
installed in the exit loop port when using a single gate operator.
#2 Terminal #4 jumpered to terminal #2 will FULLY open
bi-parting gates using a dual channel plug-in loop detector
installed in the exit loop port when using dual gate operators.
5
11
12
ON
This input ONLY fuctions when gate is fully opened or in the
closing cycle.
• When gate is closing: SW 1, switch 7 is OFF, an input to
terminal #6 (eg: photo beam gets obstructed) will reverse and
open the gate.
Note: If the auto-close timer is ON, when
gate reaches the open position, timer will
not close the gate. Another input command
SW 1 is Upside-Down on Board
is needed to reset and close the gate.
ON
NC
9210-065-M-9-14
SW 1 is Upside-Down on Board
NO
Relay contacts can be set for
Normally Open (NO) or Normally
Closed (NC) operation.
Contact rating is 1 amp maximum
at 24-volts DC.
1 2 3 4 5 6 7 8
Operation of relay is dependent on
setting of SW 1, switches 4 and 5.
See page 20 and 21 for DIP-switch
function descriptions.
6
For long gate applications. An input device connected to
terminal #5 will open the gate to the partial open setting,
See page 22 for more information.
1 2 3 4 5 6 7 8
Main Terminal Input LEDs Note: The LED
that is above the main terminal wiring input
will light when that terminal input gets
activated.
• When gate is closing: SW 1, switch 7 is ON, an input to
terminal #6 (eg: photo beam gets obstructed) will stop the
gate, then continue to close the gate when input is clear
(Used to help prevent tailgating vehicles from unauthorized
enrty). See page 21 for more information.
29
5.2 Control Wiring for Single/Primary Operator
Important: Controls intended for user activation must be located at least six (6) feet away from any moving part of the gate and
where the user is prevented from reaching over, under, around or through the gate to operate the controls.
Emergency access controls only accessible by authorized personnel (e.g., fire, police, EMS) may be placed at any location in the
line-of-sight of the gate.
P7
UL 325 Terminal
NO
See pages 25-27
NC
4404
Auxiliary Common
Terminal
Connect any common
wire to these 2 terminals.
20 19 18 17 16 15 14 13 12 11 10 9
7
6 5 4 3
Green Close
White Com
1 2 3 4 5 6 7 8
ON
3-Button Control Station
SW 1 is Upside-Down on Board
DoorKing ONLY
SW 1, Switch 3 MUST be ON
except for dual operators or
exit loop partial open
applications.
9235 Model Operator
1495-010
P2
CY
2 1
#1-Com
#2-Fully opens gate.
Safety Opening Device
#1-Com
HIGH SPEED
ADJUST
GEN
R
EME
#4 - Full Open
Red Full Open
#5 - Partial Open (See page 22)
Note: All stand-alone and
telephone entry devices must
use a separate power source.
8
#2 or #5-Relay
#3-24 volt
250 mamp. max.
E
LOS
C
Stand-Alone
Push-Button
P1
3-Wire Radio Receiver
SLOW SPEED
ADJUST
Telephone Entry
“Optional” REVERSE GATE
for Closing Direction
Photo Sensors
Functions ONLY during gate closing cycle.
1 2 3 4 5 6 7 8
Key Switch
#1-24 Volt Power Com
#1-Relay Com
#2 or #5-Relay
#3-24 Volt Power
4-Wire Radio Receiver
ON
SW 1 is Upside-Down on Board
SW 1, switch 7: After photo sensor beam
gets obstructed:
OFF Setting - REVERSES GATE.
Stand-Alone
Keypad
Com
Stand-Alone
Card Reader
30
ON Setting - Stops gate then continues
closing when gate is clear (Same function
as UL 325 terminal #2).
Note: The ON setting is used to help
prevent tailgating but the photo sensor
should be wired to the UL 325 terminal #2
when the “stop gate” function is desired,
see page 26 for more information.
To #4 or #5
#5 Terminal Note: Any opening
device connected to terminal #5 will
open the gate to the partial open
setting. Secondary entrapment
protection devices will also open the
gate to the partial open setting. If the
Inherent Reverse Sensor gets
activated during the close cycle, it
will always fully open the gate.
9210-065-M-9-14
5.3 Auxiliary Device Wiring
P7
NO
NC
4404-010
4404
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4 3
2 1
Gate Tracker - DoorKing Access Control System (Model 1833, 1835, 1837 or
1838) tracker system can be connected. This system can keep track of gate
operator cycle count, shorted inputs, loop detector problems, any forced entry
attempts, if the gate has struck anything during the open or close cycle,
power interruptions, etc. For more detailed information refer to the Tracker
Installation and Wiring Manual, DoorKing P/N 2358-010.
Terminal #2 (Full open) or #5 (Partial open) required only if the tracker
board will activate the gate operator. Refer to the manual 2358-065 for
detailed information.
9210-065-M-9-14
Gate Tracker
(Quad Box Shown)
31
5.4 Bi-Parting Gates Wiring - Dual Gate Operators
P7
NO
1 2 3 4 5 6
• Requires AC power to each operator.
UL 325
Terminal
NC
4404-010
4404
• Both operator DIP-switches must be set.
• Connect all control devices, auxiliary
devices and loops to the primary
operator only.
Primary Operator
8
Brown
3-Wire Receiver
Com
Relay
Note: 4-wire
radio receiver, or
any other
opening devices
get wired to
primary operator
ONLY, as shown
on page 30.
PVC Conduit
A
SW 1 is Upside-Down on Board
Primary SW 1, switch 3
must be OFF.
Com to #1
LOOP 2
Automatic
Exit Loop
24 Volt Power
250 mamp. max.
When using plug-in
loop detector
Connect a jumper
from #4 to #2:
fully opens gates.
ON
A
Normally Open to #6
Reverse loop
lead-in wires are
twisted approx.
6 twists per foot
and are wired in
series.
PVC Conduit
Dual Channel
9409
B
Plug the DoorKing DUAL
channel loop detector
into Primary Operator’s
Exit Loop Port.
LOOP 1
Sold separately from DoorKing.
5 wires used (8 - 18 AWG wires total).
Green to primary operator
chassis ground.
1 2 3 4 5 6 7 8
Reverse
Loop
Loop Lead-In Wires
Interconnection Cable
2 1
Loop Detector
Reverse
Loop
B
6 5 4 3
Gray
Orange
DoorKing offers a free “Loop and Loop-Detectors
Information Manual” PDF located at Doorking’s
web site for more information. www.dkaccess.com
7
Yellow
20 19 18 17 16 15 14 13 12 11 10 9
To Open Photo #1
Secondary Entrapment
Protection Devices
for Bi-Parting Gates
To Close Photo #2
To Open Edge #3
To Common #5
Exit loop lead-in
wires are twisted
approx. 6 twists
per foot.
To Open Edge #3
Closing Non-Contact Sensor
Fence
Fence
Opening Contact Sensor
Opening Contact Sensor
Gate
Filler Post if necessary (See page 4 for more info).
Gate
Opening Non-Contact Sensor
Opening Non-Contact Sensor
Primary
Operator
Secondary
Operator
To Open Edge #3
To Open Photo #1
• Separate power source for photo sensors.
See page 25 for more information.
To Common #5
P7
NO
1 2 3 4 5 6
NC
4404-010
4404
UL 325
Terminal
Secondary Operator
32
2 1
Yellow
6 5 4 3
Brown
7
Orange
8
Gray
20 19 18 17 16 15 14 13 12 11 10 9
Note: Secondary operator ‘s
DIP-switches MUST be set for
the dual operators to cycle
correctly. See pages 20 and 21
for more information about dual
operator DIP-switch settings.
Green to secondary operator
chassis ground.
9210-065-M-9-14
SECTION 6 - OPERATING INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING - To reduce the risk of injury or death:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with gate controls. Keep the remote control away from children.
3. Always keep people and objects away from gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
4. Test the operator monthly. The gate MUST reverse on contact with a rigid object or stop or reverse when an object
activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to
adjust and retest the gate operator properly can increase the risk of injury or death.
5. Use the emergency release only when the gate is not moving and power has been shut-off.
6. KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a qualified service person make repairs to gate
hardware.
7. The entrance is for vehicles only. Pedestrians must use separate entrance.
8. SAVE THESE INSTRUCTIONS.
6.1 AC Power and Reset Button(s)
Motor Reset Button
On select 1 HP models.
Used to reset the motor
when weight overload
or overheating occurs.
Press firmly to reset.
CA
CO
NF
AN OR
SI/ MS
UL TO
-32
CE
5
N/C RT
SA IFIED
C2
2.2 TO
HI
NO
CU
. 24
LA
7
R
S
GA
VE
533
CL
AS
MO
DE
L
SE
RIA
L
VO
LTS
TE
82
OP
ER
AT
HP
OR
AM
PS
MA
X GA
TE
LO
AD
Do
orK
ing
, Inc
.,
PH
60
AS
E
Hz
Ing
lew
oo
d,
CA
RESET
WA
R
NIN
G
MOV
SE IN
RI G
OU GA
Op
S IN TE
era
and te
JU CAN
free gate
RY CA
of onl
Do
OR US
peo y wh
ple en
or not allo
DE E
and gat
ope
AT
rate w chi
obs e are
H
Do
tru a is
gat ldre
ctio in
e.
n to
pat not sta
ns. sig
h wh nd
pla
ht
y in
ile in
gat
Rea
gat gat
e are
e is e pat
d ow
mo h
a
ner
vin or wa
’s
g.
ma
lk
nua
thr
oug
l and
h
saf
ety
ins
tru
ctio
ns.
Unlock the power switch cover and
open to access the main power, and the
operator reset button.
RESET
AC
POWER
Reset Button - Used to turn off the
entrapment alarm and to reset the
operator after a HARD shutdown has
occurred.
Alarm Siren
AC Power Switch - Powers the operator
ON (toggle up) or OFF (toggle down).
OFF
9210-065-M-9-14
33
6.2 Shutdown Conditions
Under various entrapment conditions the operator will assume either a soft or hard (alarm) shutdown. To determine what
type of reset action is required, you will need to understand how the different entrapment conditions affect the gate operator.
Soft Shutdown
This occurs in various situations where the inherent or secondary entrapment protection devices have been activated. In a soft
shutdown condition, the operator will not respond to any input that was present when the entrapment protection device sensed an
obstruction. If the gate stops at the open position, the operator will not respond to the automatic close timer.
• Example 1 - A time clock keys the gate open in the morning and an entrapment protection device senses an
obstruction prior to the gate reaching the full open position. If the entrapment is sensed by the inherent system, the
gate will reverse and run back to the closed position. The time clock input is still present, but the gate will not re-open.
Note: In some systems, the time clock input comes from the telephone entry system relay. This same relay may also provide open
commands for a card reader, MicroPLUS transmitters and the visitor telephone entry. If so, these devices will also be disabled in a
soft shutdown condition.
• Example 2 - If the gate is closing and an entrapment protection device is activated, the gate will either stop or reverse
and run back to the open position, depending upon if the secondary or inherent device was activated. The automatic
close timer will not close the gate.
• Example 3 - Vehicle arrives at exit loop and gate runs towards the open position. If the inherent entrapment protection
gets activated during this opening cycle, the gate reverses and runs back to the closed position. After the inherent
entrapment protection is cleared, If the vehicle is still present at the exit loop, a soft shutdown condition does not
occur. The exit loop input provides an immediate reset of the operator and the gate will again run to the open position.
Resetting a Soft Shutdown
In some conditions, a soft shutdown will reset as soon as the entrapment condition clears. For example, if a non-contact sensor
(photo cell) is sensing an obstruction, the operator will stop the gate and assume a soft shutdown condition. When the photocell
clears, the operator will return to normal operation.
When the operator is in a soft shutdown, activation of any “intended input” will reset the operator. An “ intended input” includes
any command, any standard safety input and any loop input. Activating any of these inputs will reset the gate. At that point the
gate will return to normal operation. If the gate is open, the automatic close timer will then time out and close the gate.
Hard Shutdown (Alarm Activated)
A hard shutdown condition occurs when: (1.) The inherent entrapment protection system (Type A) gets activated TWO
consecutive times before the gate completes the open or close cycle. (2.) The reversing edge (Type B2) gets activated
and reverses but before the gate completes the reverse cycle the inherent entrapment protection system (Type A) gets
activated.
• Example of a Hard Shutdown - The gate is closing and the inherent entrapment protection system senses an obstruction and
causes the gate to reverse direction. As the gate begins to run in the open direction, a second obstruction is sensed prior to the
gate reaching the full open position. Once the second obstruction has been sensed, the operator will stop, the audio alarm will
sound and all standard inputs are shut down (including open commands, safety commands, loop inputs, etc.).
– To silence the alarm, press the reset button or after 5 minutes, the audio alarm will shut off but will “chirp” every 5
seconds. This indicates that the operator is in a hard shutdown condition (The reset button must be pressed to reset the
operator and stop the alarm “chirping”).
Resetting a Hard Shutdown
The operator is in a hard shutdown condition when the audio alarm is sounding OR “chirping” every 5 seconds.
• Before resetting a hard shutdown, determine why the shutdown occurred. Inspect the gate for any obstructions along
its path that could have activated the inherent entrapment sensing system. Inspect the gate and gate hardware.
The audio alarm will sound for five minutes, or until the operator’s reset button is pushed. After (5) five minutes the
alarm will “chirp every 5 sec.” and the hard shutdown condition will remain in affect until the reset button is pushed.
Once the operator has been reset, an open or close command is needed to start the gate operator. Most activating commands
will cause the gate operator to cycle to the open position. This includes activation of a key switch or open command and
activation of an automatic exit loop. Activation of a close command will run the gate to the closed position.
Note: DoorKing operators have a built-in alarm reset push button mounted on the operator (See previous page for reset button location).
Activating this button will return the gate operator to normal operation, but will not cycle the gate operator.
34
9210-065-M-9-14
6.3 Manual Gate Operation
Caution: Never attempt to manually operate any gate until you have verified that power to the operator has been shut-off.
2
1
Insert the supplied manual hand crank into the
access hole until it engages with the motor shaft.
Turn the crank to open the gate. 9235 mechanical
disc brake model operators MUST also
have the disc brake manually
released before manually
cranking the hand crank
(See below).
M
a
Acc nua
ess l C
Pan rank
el
Unlock Manual Crank
Access Panel
Cuts off AC power to the operator.
Manual Crank
Mo
Sh tor
aft
2
1
2
1
1
3
4
2
3
4
3
4
RESET
EXIT
LOOP
LMT
LOOP
REVERSE
REV SENSE
CLOSE
CA
CO
NF
AN OR
SI/ MS
UL TO
-32
CE
5
N/C RT
SA IFIED
C2
2.2 TO
NO
CU
. 24
LA
AS
7
R
S
GA
WA
R
VE
HI
533
CL
MO
SE
TE
DE
L
RIA
82
OP
ER
AT
HP
OR
NIN
G
BL2
LTS
L1
AM
PH
AS
E
60
Ing
lew
.
B+
L3
L
VO
PS
MA
X GA
TE
LO
AD
Do
orK
ing
, Inc
.,
Ma
cranual
stonk in
po red
siti
on
Hz
ood
, CA
MOV
SE IN
RI G GA
OU
Op
S IN TE
era
and te
JU CAN
free gate
RY CA
of onl
Do
OR US
peo y wh
ple en
or not allo
DE E
and gat
ope
AT
rate w chi
obs e are
H
Do
tru a
gat ldre
EP
ctio is in
e.
n to
pat not sta
ns. sig
h wh nd
pla
ht
y in
ile in
gat
Rea
gat gat
e are
e is e pat
d ow
mo h
a
ner
vin or wa
’s
g.
ma
lk
nua
thr
oug
l and
h
saf
ety
ins
tru
ctio
ns.
Mod
00
0
M
ies
ser l
MO contro
SC
I/
sic
e
6
ft/s
5
1.5
1
2
1 ft/s
11
13A
13B
13E
25
16
17
ba
.5
ft/s
2 ft/s
0 ft/s
EXIT
LOOP
REV SENSE
CLOSE
Tur
1/4n ma
n
to turn ual r
rel clo ele
dis eas ck ase
c b e th wis
rak e e
e.
LMT
R
E
L
E
A
S
E
REVERSE
MA
RE NU
LEAAL
SE
LOOP
R
E
S
E
T
Dis
c
Bra
k
Ac e
ces
Pa s
nel
R
E
S
E
T
MANUAL
RELEASE
R
E
L
E
A
S
E
9235
Mechanical Disc
Brake
The disc brake MUST be manually
released (disengaged) with a slotted
screwdriver (Not provided) before
manually operating the gate.
Disc brake will automatically
reengage after power has been
restored.
9210-065-M-9-14
35
SECTION 7 - MAINTENANCE AND TROUBLESHOOTING
Inspection and service of this gate operator by a qualified technician should be performed anytime a malfunction is observed or
suspected. High cycle usage may require more frequent service checks.
7.1 Maintenance
When servicing the gate operator, always check any secondary (external) reversing devices (loops, photocells, etc.) for proper
operation. If external reversing devices cannot be made operable, do not place this operator in service until the malfunction can
be identified and corrected.
Always check the inherent reversing system when performing any maintenance. If the inherent reversing system cannot be
made operable, remove this operator from service until the cause of the malfunction is identified and corrected. Keeping
this operator in service when the inherent reversing system is malfunctioning creates a hazard for persons which can result
in serious injury or death should they become entrapped in the gate.
When servicing this gate operator, always turn power OFF!!
If gearbox requires oil, use only Mobil SHC-629 Synthetic Gear Oil. Do not completely fill gearbox with oil. Gearbox
should be half full only. Do not exceed this level.
Operator
Component
36
Monthly Interval
Maintenance
Alarm
Activate the primary (inherent) reverse system by blocking the
gate with a solid object. When the gate reverses, block the gate
in the opposite direction prior to the limit being reached. The
entrapment alarm should activate. Press the reset button to
silence the alarm.
Chain
Check for sagging. Tighten if necessary.
Fire Dept.
Check emergency vehicle access device for proper operation.
Gate
Inspect for damage. Check gate wheels. rollers and guides for
wear and grease if necessary.
Grease
Wheels and guide rollers if necessary.
Loop(s)
Check vehicular exit and reverse loops for proper operation.
Primary Reverse System
Check that the gate reverses on contact with an object in both
the opening and closing cycles.
Adjust the reversing sensor if necessary.
Release
Check manual release for proper operation.
Secondary Reverse Device
Check secondary (external) reverse device(s) stop or reverse the
gate when activated.
Sprockets
Check set screws for tightness.
Complete System
Complete check of gate and gate operating system.
3
6
12
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
9210-065-M-9-14
7.2 Built-In Diagnostic Tests
This gate operator is designed with built-in diagnostics that will alert you to potential or existing problems that the microprocessor has detected. Specific fault conditions are checked and the operator will signal that a fault exist through the built-in alarm.
Constant alarm is heard when power is applied: This indicates that the limit switch wire harness is not
connected to the circuit board. In this condition, the operator will not run and the tone will continue until the fault is
corrected. Check to be sure that the limit switch plug is properly inserted into the limit switch plug on the circuit
board.
Constant alarm is heard: This indicates that the operator is in a hard shutdown condition (section 6.2 on page
34). The tone will continue to sound for five minutes, and then will beep once every five seconds. The operator-reset
button must be pressed or power must be removed and then reapplied to return the operator to normal operation.
Short “chirp” is heard every five seconds: This indicates that the operator has been in a hard shutdown
condition in excess of five minutes. This will continue until the operator-reset button is pressed or until power is
removed from the operator (section 6.2 on page 34).
Operator runs for 1 second and stops, two short “chirps” are heard: This indicates that there may be
a fault with the current sensor circuit.
7.3 Troubleshooting
Have a good VOM meter to check voltages and continuity. A Meg-Ohm meter capable of checking up to 500 meg-ohms of
resistance is necessary to properly check the integrity of the ground loops. When a malfunction occurs, isolate the problem to
one of three areas: 1. the operator, 2. the loop system, 3. the keying devices. Use caution when checking high voltage
terminals, motor capacitor and the motor.
1. Check the input indicator LEDs. They should only come ON when a keying device (card reader, push button, etc.) is activated.
If any of the input LEDs are ON continuously, this will cause the gate operator to hold open. Disconnect the keying devices one
at a time until the LED goes OFF.
2. Check any external secondary entrapment protection devices. Any short or malfunction in these devices can cause the gate
operator to stop or to hold open.
3. A malfunction in a loop or loop detector can cause the gate operator to hold open, or to not detect a vehicle when it is
present over the loop. Pull the loop detector circuit boards from the loop ports on the operator circuit board. If the malfunction
persists, the problem is not with the loop system. For more information on trouble shooting loops and loop detectors, refer to
your loop detector instruction sheet and to the DoorKing Loop and Loop Detector Information Manual located on DoorKing’s
web site.
4. Check to be sure that there are no shorted or open control wires from the keying devices to the gate operator. If a keying
device fails to open the gate, press the Key Switch or momentarily jumper across terminals 1 and 4 on the operator circuit
board. If the gate operator starts, this indicates that a problem exist with the keying device and is not with the gate operator.
5. If a three-button control station (open-close-stop) is connected to this gate operator, check for proper wiring. Only a
DoorKing three button control station (P/N 1200-006 or 007) can be used with this gate operator. Others will cause a
malfunction.
6. Check the high voltage supply. A voltage drop on the supply line (usually caused by using too small supply voltage wires) will
cause the operator to malfunction. Refer to the wire size chart in section 2.1 on page 17.
9210-065-M-9-14
37
Symptom
Operator will not run.
Power LED is OFF.
38
Possible Solution(s)
• Check that AC power to the operator is turned ON.
• Transformer may be overheated. Turn power off and allow board to cool for several minutes then retest. Check
for low VAC power and low voltage shorts.
• Check for VAC at high voltage input terminal. If voltage measures 0, check the incoming power wires or
replace the circuit board.
Gate opens a short
distance, then stops
and reverses.
• Disconnect the gate from the gate operator and check that the gate slides freely without any binding.
• Re-adjust the reverse sensitivity.
• Continue troubleshooting or replace circuit board.
Gate opens but
will not close.
• Check the input LEDs. Any ON will hold the gate open and indicates a problem with a keying device.
• Check the secondary safety devices. Any activated will hold the gate open and indicates a problem with the
safety device.
• Check the loop detectors. Any activated can hold the gate open and indicates a problem with the loop detector
or ground loop.
• Operator may be in a “soft shutdown.” Activate any keying device to determine if operator returns to normal
operation.
• If automatic close is desired, be sure SW 1, switch 2 is ON and set timer open from 1-23 seconds.
• Bypass circuit board and check motor as above.
Gate closes but
will not open.
• Operator may be in a “soft shutdown.” Check input LEDs. If any are ON, momentarily disconnect, then
re-connect the wire going to the respective terminal. Operator should open.
• Check to be sure that the operator is running in the proper direction. Turn power OFF, and then back ON.
Activate a keying device. Operator should run in the open direction. If operator runs in the close direction, turn
power OFF and change direction switch SW 1, switch 1. Go to above section if operator now opens but will not
close.
• Be sure that the each LED on the control board lights when the keying device connected to the that terminal is
activated. If LED does not light, momentarily place a jumper wire from terminal 1 to the input terminal being
checked. If LED lights and gate opens, problem is with the keying device. If LED does not light, replace control
board.
• Bypass circuit board and check motor as described above.
Gate starts to close,
then reverses to open.
•
•
•
•
Gate closes then
re-opens.
• Check for any input or loop detector LED’s that are ON.
• Check that the operator is running in the proper direction (see “gate closes but will not open”).
Alarm is sounding.
Operator will not run.
• Operator is in a “hard shutdown” condition. Reset button must be pushed to return operator to normal
operation, see Section 6.2 Shutdown Conditions, page 34.
• Check the gate and gate hardware for any binding, correct where necessary.
• Gate may be too heavy.
Alarm chirps once
every 5 seconds.
Operator will not run.
• Operator has been in a “hard shutdown” condition in excess of 5 minutes. Reset button must be
pushed to return operator to normal operation, see Section 6.2 Shutdown Conditions, page 34.
Alarm sounds when
power is applied and
operator will not run.
• The limit switch wire harness is not plugged into the circuit board. Check that the limit switch connector is
properly plugged into the limit switch plug on the circuit board.
Operator runs for 1
second and stops, two
short chirps are heard.
• There may be a problem with the current sensor on the circuit board. Replace the circuit board.
Re-adjust the reverse sensitivity.
Disconnect the gate from the gate operator and check that the gate slides freely without any binding.
Check the loop detector LEDs and input LEDs. Any that flash ON will cause the gate to reverse.
Continue troubleshooting or replace circuit board.
9210-065-M-9-14
7.4 Accessory Items
The following accessory items are available for the series 9200 slide gate operators.
Contact Sensors - For use as a secondary entrapment protection device. Miller Edge, Inc., MGO20, MGR20, MGS20
Chain Tray Kit - 10 Ft. section. Sections connect together to fit any length gate. P/N 2601-270
Pedestal Mounting Stand - Heavy-duty pedestal mounting stand for the 9200 series operator. P/N 9200-135
Heater and Fan Kit - Recommended for cold weather climates.
P/N 1601-195: 115 VAC models
P/N 1601-197: 208/230 VAC models
Photo Cell - Non-contact (photocell) sensors for use as a secondary entrapment protection device.
MMTC, Inc. Model 60-278 - P/N 8080-011
Carlo Gavazzi Type PMP12 - P/N 8080-030
Carlo Gavazzi Type PMT - P/N 8080-031
Note: DO NOT USE MMTC, Inc. Model IR55 - P/N 8080-010 for the 9200 series slide gate operator.
Loop Detector - Detectors plug directly into ports on circuit board simplifying wiring.
Single channel detector - P/N 9410-010 Dual channel detector - P/N 9409-010
Loop Wire - 18 AWG loop wire with XLPE insulation is ideal for ground loops. Available in 500 and 1000 foot rolls. Red, blue or
black insulation.
Pre-Fab Loops - Prefabricated ground loops. 24-foot circumference with 50-foot lead-in. Available in yellow, red or blue jackets.
Not for use in asphalt roadways.
Loop Test Meter - Meg-ohm meter checks the integrity of ground loops. P/N 9401-045
3-Button Control Station - Provides open-close-stop manual operation of the gate.
Stand Alone Box - P/N 1200-006 Interior (fits in single gang box) - P/N 1200-007
Interconnection Cable - Interconnect wire cable contains all the necessary wires to interconnect primary / secondary operators.
Cable length: 30 ft. - P/N 2600-755 40 ft. - P/N 2600-756 50 ft. - P/N 2600-757
Time Clock - 7 day and 365 day time clocks can be used to automatically open gate at pre-set time and days. Compact clock fits
inside the operator. 7 day clock - P/N 2600-791 365 day clock - P/N 2600-795
V-Wheels - 4 inch and 6 inch. UHMW or Steel. Roller bearings or sleeve bearings. Single or tandem wheel configurations.
Surge Devices - High and low voltage surge suppressors help prevent circuit board failure caused by lightning strikes and
power surges. High Voltage - P/N 1876-010 Low Voltage - P/N 1878-010
Gate Scale - Use to test torque required to move gate. P/N 2600-225
Speed Bumps - Prefabricated six-foot speed bump reduces traffic speed through gate system. P/N 1610-150
9210-065-M-9-14
39
Model 9210 1 HP 1-Phase 115 VAC
50uf Capacitors
Yellow
Blue
Blue
Black
Red
Orange
1 HP 115 VAC
Single Phase
Limit Assembly
Blue
2
1
VDC +
2
3
4
VDC +
3
VAC
1
Relay
State
Solid
4
VAC
White
Black
VAC
1
P/N 2600-348
Red
Gear Reducer
40:1
Yellow
White
Orange
Blue
P/N 2600-278
Black
Reset Button
NO
3
Com
Partial
Open
Limit
Sensor
Relays
4
VDC +
Black
Bottom Limit
Com
Red
White
Yellow
White
Blue
Top Limit
2
NO
White
Com
Blue
NO
115 VAC
Convenience
Outlets
EXIT
LOOP
LMT
LOOP
REVERSE
Power
Black
Limit
Switch
Plug P2
Neutral
White
LMT
P2
Red
Blue
Red
White
1 2 3 4
L2
ON
L1
TIME
DELAY
Neu
P6
Hot
REV SENSE
CLOSE
Motor Plug P6
1 2 3 4 5 6 7 8
White
ON
Black
REV SENSE
OPEN
Black
Chassis
Ground
P8
Yellow
White
P7
Com
4404-010
Auxiliary
Common
Terminal
NC
Interlock
NO
Board Ground
NO
Black
VAC Input Power
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4
3
White
Red
Red
White
Yellow
Black
Green
Black
2 1
Alarm Reset
White
Black
Alarm
Black
Red
Current Sensor
AC Power
40
Black
Black
9210-065-M-9-14
Model 9210 1 HP 1-Phase 208/230 VAC
Gear Reducer
40:1
30uf Capacitor
P/N 2600-348
Yellow
Blue
Black
Red
Orange
1 HP
Single Phase
Blue
P/N 2600-280
Reset Button
Red
Black
2
3
4
VDC +
3
VAC
1
Relay
State
2
Limit Assembly
Relays
VDC +
4
White Com
Blue
NO
3
Black
Partial
Open
Limit
Sensor
Red
Yellow
Com
Red
Bottom Limit
Com
Red
EXIT
LOOP
LMT
Red
LOOP
Blue
REVERSE
1
2
3
4
5
Limit
Switch
Plug P2
Blue
Black
1 2 3 4
1 2 3 4 5 6 7 8
ON
ON
TIME
DELAY
Blue
P6
REV SENSE
CLOSE
Motor Plug P6
White
Red
REV SENSE
OPEN
Yellow
LMT
P2
P8
AC Power
Power
Black
P7
Neutral
L1
L2
NO
Board Ground
8
7
6 5 4
3
White
2 1
White
Red
Green
Black
VAC Input Power
20 19 18 17 16 15 14 13 12 11 10 9
Red
Hot
Auxiliary
Common
Terminal
Black
Hot
White
4404-010
NC
Blue
NO
White
Red
NO
Black
Blue
White
White
White
115 VAC
Convenience
Outlets
Chassis
Ground
Top Limit
NO
White
208 VAC
OR
230 VAC
230 Step-Down
Transformer
VDC +
4
Blue
Red
208 Step-Down
Transformer
Blue
VAC
Black
1
Red
2
Solid
1
2
3
4
5
Yellow
VAC
1
Orange
Black
Blue
Black
White
Yellow
Interlock
Alarm Reset
Com
Black
White
Black
Alarm
Black
Red
Current Sensor
9210-065-M-9-14
41
Model 9210 1 HP 3-Phase 208/230 VAC
Black
1 HP
Three Phase
Blue
Red
P/N 2600-295
A1
Red
Blue
A2
Red
Black
C1 VAC
B2
C2
White Com
Blue
NO
VDC
Top Limit
NO
Black
Blue
Red
Partial
Open
Limit
Sensor
Com
NO
Bottom Limit
Com
Red
White
White
Red
1
2
3
4
5
Limit Assembly
D1
D0
D2
Black
208 VAC
OR
230 VAC
Blue
Blue
EXIT
LOOP
Black
LMT
Blue
LOOP
Red
REVERSE
230 Step-Down
Transformer
B1
Solid State Relay
Black
208 Step-Down
Transformer
White
Black
P/N 2600-348
1
2
3
4
5
Blue
Red
Gear Reducer
40:1
ON
Red
White
1 2 3 4
1 2 3 4 5 6 7 8
ON
Blue
LMT
TIME
DELAY
REV SENSE
CLOSE
Black
Motor Plug P6
P6
Power
Red
REV SENSE
OPEN
AC Power
P2
P8
115 VAC
Convenience
Outlets
Limit
Switch
Plug P2
Neutral
White
P7
Blue
L2
L3
Black
VAC Input Power
NO
Interlock
8
7
6 5 4
3
White
2 1
White
Red
Green
Red
L1
20 19 18 17 16 15 14 13 12 11 10 9
Black
Red
Hot
Board Ground
Chassis
Ground
Hot
Auxiliary
Common
Terminal
NC
Black
NO
Hot
White
4404-010
Yellow
Alarm Reset
Com
Black
White
Black
Alarm
Black
Red
Current Sensor
42
9210-065-M-9-14
Model 9210 1 HP 3-Phase 460 VAC
Black
Blue
Red
1 HP
Three Phase
P/N 2600-295
Black
Blue
Red
Gear Reducer
40:1
P/N 2600-348
A1
B1
C1 VAC
B2
C2
White Com
Blue
NO
VDC
Top Limit
White
NO
Blue
Partial
Open
Limit
Sensor
Black
Blue
1
2
3
4
5
Red
Com
Red
Black
NO
Bottom Limit
Black
460 Step-Down
Transformer
A2
Limit Assembly
D1
D0
D2
Solid State Relay
Com
Red
White
Blue
EXIT
LOOP
LMT
LOOP
REVERSE
ON
Red
White
1 2 3 4
1 2 3 4 5 6 7 8
ON
Blue
LMT
TIME
DELAY
REV SENSE
CLOSE
Black
Motor Plug P6
P6
Power
Red
REV SENSE
OPEN
AC Power
P2
P8
115 VAC
Convenience
Outlets
Limit
Switch
Plug P2
Neutral
White
P7
Blue
L2
L3
Black
VAC Input Power
NO
Interlock
8
7
6 5 4
3
White
2 1
White
Red
Green
Red
L1
20 19 18 17 16 15 14 13 12 11 10 9
Black
Red
Hot
Board Ground
Chassis
Ground
Hot
Auxiliary
Common
Terminal
NC
Black
NO
Hot
White
4404-010
Yellow
Alarm Reset
Com
Black
White
Black
Alarm
Black
Red
Current Sensor
9210-065-M-9-14
43
Model 9220 2 HP 1-Phase 208/230 VAC with Speed Controller
Shielded Cable
B- B+
Gear Reducer
40:1
2 HP
Single Phase
P/N 2600-348
P/N 2600-263
Red
Blue
Black
Orange
White
Blue
1
2
3
4
5
Red
L1 L2/N
PE
Black
1. 0
EPM
208 VAC
OR
230 VAC
Speed
Controller
Mode
SCM series
1.5 ft/s
White Com
208 VAC P/N 9210-410
230 VAC P/N 9210-411
1 ft/s
.5 ft/s
Limit Assembly
Speed
Controller
Blue NO
208 Step-Down
Transformer
Black
Top Limit
Com
basic I/O control
Red
U
V
W
Top
Slow Down
Yellow NO
17
16
1
2
5
6
11
13A
13B
13E
25
2 ft/s
Red
Black
Blue
1
2
3
4
5
Yellow
White
NO
Partial
Open
Limit
Sensor
PE PE
Com
Bottom
Slow Down
Green NO
Black NO
Red
Blue
Yellow
Blue
Com
EXIT
LOOP
LMT
115 VAC
Convenience
Outlets
LOOP
REVERSE
Red
Black
Black
Blue
230 Step-Down
Transformer
0 ft/s
LMT
AC Power
Red
Bottom Limit
Com
Limit
Switch
Plug P2
ON
Red
White
1 2 3 4
1 2 3 4 5 6 7 8
TIME
DELAY
P6
Red
REV SENSE
CLOSE
Motor Plug P6
ON
Neutral
REV SENSE
OPEN
Black
P8
Power
Black
White
Shield
Orange
Shield
Blue
White
Interlock
NO
VAC Input Power
Auxiliary
Common
Terminal
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4
3
2 1
White
Red
Red
Yellow
Black
Black
Green
Black
Com
White
L2
Board Ground
L1
4404-010
NC
Hot
NO
Hot
P7
Chassis
Ground
Blue
Yellow
Alarm Reset
Black
White
Black
Alarm
Current Sensor
Red
Black
Black
44
9210-065-M-9-14
Model 9220 2 HP 3-Phase 208/230 VAC with Speed Controller
Red
Blue
Black
Shielded Cable
Orange
Red
Black
Ground
Blue
Red
L1 L2 L3
Speed
Controller
Black
208 VAC P/N 9210-412
230 VAC P/N 9210-413
208 VAC
OR
230 VAC
1. 0
EPM
Gear Reducer
40:1
2 HP
Three Phase
P/N 2600-348
P/N 2600-263
Speed
Controller
Mode
Limit Assembly
White Com
1 ft/s
1.5 ft/s
Top Limit
Com
basic I/O control
Red
U
V
W
Top
Slow Down
17
Yellow NO
Blue
1
2
3
4
5
SCM series
2 ft/s
1
2
5
6
11
13A
13B
13E
25
Black
White
Yellow
0 ft/s
Red
.5 ft/s
230 Step-Down
Transformer
B- B+
Blue NO
1
2
3
4
5
16
208 Step-Down
Transformer
White
NO
Partial
Open
Limit
Sensor
PE PE
Com
Bottom
Slow Down
Green NO
Red
Blue
Black
Yellow
Black NO
Red
Com
EXIT
LOOP
LMT
115 VAC
Convenience
Outlets
LOOP
REVERSE
Blue
Blue
Black
LMT
AC Power
Com
Limit
Switch
Plug P2
ON
White
1 2 3 4
1 2 3 4 5 6 7 8
Red
TIME
DELAY
P6
Black
REV SENSE
CLOSE
Motor Plug P6
ON
Red
REV SENSE
OPEN
Neutral
White
Red
Bottom Limit
P8
Power
Black
Shield
Orange
Shield
Blue
P7
VAC Input Power
Interlock
Auxiliary
Common
Terminal
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4
3
2 1
Com
Green
Black
White
Red
NO
Black
Black
L3
Yellow
L2
Red
L1
4404-010
Black
Hot
White
Hot
NC
Hot
Board Ground
White
NO
Chassis
Ground
Blue
Yellow
Alarm Reset
Black
Black
White
Current Sensor
Alarm
Red
9210-065-M-9-14
45
Model 9220 2 HP 3-Phase 460 VAC with Speed Controller
Red
Blue
Black
Shielded Cable
Orange
Red
Shield
Orange
Shield
Blue
Black
Ground
460 Step-Down
Transformer
1. 0
EPM
White
Blue
1
2
3
4
5
B- B+
Speed
Controller
Mode
1.5 ft/s
P/N 2600-263
Limit Assembly
White Com
SCM series
Top Limit
Com
V
W
Top
Slow Down
Yellow NO
17
1
2
5
6
11
13A
13B
13E
25
U
16
basic I/O control
2 ft/s
Red
Black
Yellow
0 ft/s
P/N 2600-348
P/N 9210-406
1 ft/s
.5 ft/s
2 HP
Single Phase
Speed
Controller
Red
Black
Gear Reducer
40:1
Blue NO
L1 L2 L3
NO
Partial
Open
Limit
Sensor
PE PE
Com
Green NO
Red
Blue
Black
Yellow
Black NO
Red
Com
EXIT
LOOP
LMT
115 VAC
Convenience
Outlets
LOOP
REVERSE
Blue
Blue
Bottom
Slow Down
LMT
AC Power
Limit
Switch
Plug P2
ON
White
1 2 3 4
1 2 3 4 5 6 7 8
Red
TIME
DELAY
P6
Black
REV SENSE
CLOSE
Motor Plug P6
ON
Red
REV SENSE
OPEN
Neutral
White
Com
P8
Power
Black
Red
Bottom Limit
P7
Interlock
NO
VAC Input Power
Auxiliary
Common
Terminal
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4
3
2 1
Com
Black
White
Red
Green
Black
L3
Yellow
L2
Red
L1
4404-010
Black
Hot
White
Hot
NC
Hot
Board Ground
White
NO
Chassis
Ground
Blue
Yellow
Alarm Reset
Black
White
Black
Current Sensor
Alarm
Red
Black
Black
46
9210-065-M-9-14
Model 9230 3 HP 3-Phase 208/230 VAC with Speed Controller
Black
Ground
Blue
Gear Reducer
40:1
Red
L1 L2 L3
P/N 2600-404
Black
1. 0
EPM
208 VAC P/N 9210-414
230 VAC P/N 9210-415
208 VAC
OR
230 VAC
AC Tech Brake
Speed
Controller
Mode
Limit Assembly
White Com
Blue NO
Speed
Controller
1 ft/s
1.5 ft/s
Blue
1
2
3
4
5
SCM series
Top Limit
Com
basic I/O control
42
43
46
47
17
1
2
5
6
11
13A
13B
13E
25
2 ft/s
Red
Black
White
Yellow
0 ft/s
16
.5 ft/s
230 Step-Down
Transformer
3 HP
Three Phase
P/N 2600-348
B- B+
B-
B+
Red
White
Red
U
V
W
PE PE
Top
Slow Down
Yellow NO
208 Step-Down
Transformer
White
1
2
3
4
5
Red
Black
White
Shielded Cable
Orange
Red
NO
Partial
Open
Limit
Sensor
Red
Blue
Com
Black
Bottom
Slow Down
Green NO
Red
Black
White
Yellow
Black NO
Red
Com
EXIT
LOOP
LMT
115 VAC
Convenience
Outlets
LOOP
REVERSE
Blue
Blue
Black
LMT
AC Power
Com
Limit
Switch
Plug P2
ON
White
1 2 3 4
1 2 3 4 5 6 7 8
Red
TIME
DELAY
P6
Black
REV SENSE
CLOSE
Motor Plug P6
ON
Red
REV SENSE
OPEN
Neutral
White
Red
Bottom Limit
P8
Power
Black
Shield
Orange
Shield
Blue
P7
Interlock
NO
VAC Input Power
Auxiliary
Common
Terminal
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4
3
2 1
Com
Black
White
Red
Green
Yellow
L3
Red
L2
Black
L1
4404-010
Black
Hot
White
Hot
NC
Hot
Board Ground
White
NO
Chassis
Ground
Blue
Yellow
Alarm Reset
White
Black
Black
Alarm
Red
Current Sensor
Black
Black
9210-065-M-9-14
47
Model 9235 3 HP 3-Phase 208/230 VAC with Speed Controller
Blue
Red
Black
Red
Black
White
Shielded Cable
Gear Reducer
10:1
Speed Controller
P/N 2600-388
Red
208 VAC P/N 9210-416
230 VAC P/N 9210-417
Shield
Orange
Shield
Orange
Ground
3 HP
Three Phase
P/N 2600-404
208 Step-Down
Transformer
White
Blue
Red
White
Black
L1
L2
VAC
4. 0
Blue
1
2
3
4
5
Limit
Assembly
Red
White Com
AC Tech Brake
Com
1
2
5
6
11
12
2
14
13A
13B
13C
15
25
2
30
31
TXA
TXB
T1
T2
T3
U
V
W
B-
NO
Partial
Open
Limit
Sensor
B+
Com
Green NO
Yellow
Com
Black NO
Red
Black
White
Bottom
Slow Down
Red
EXIT
LOOP
LMT
LOOP
Blue
Blue
B+
Red
Blue
REVERSE
Red
B-
White
Black
115 VAC
Convenience
Outlets
LMT
AC Power
Red
Bottom Limit
Com
Limit
Switch
Plug P2
P8
Red
White
1 2 3 4
ON
Red
TIME
DELAY
Black
REV SENSE
CLOSE
P6
Motor Plug P6
1 2 3 4 5 6 7 8
Neutral
REV SENSE
OPEN
Speed Brake Plug P8
ON
Power
White
Top
Slow Down
42
43
46
47
Red
Black
Black
Top Limit
basic I/O control
Red
Black
White
Black
SCF series
4 ft/s
Yellow
0 ft/s
3
Blue NO
Mode
3 ft/s
VDC +
4
Speed
Controller
2 ft/s
1 ft/s
2
Solid State
Relay
Yellow NO
208 VAC
OR
230 VAC
R
E
L
E
A
S
E
L3
1
EPM
MANUAL
RELEASE
Mechanical
Speed
Brake
Black
Black
Blue
Black
230 Step-Down
Transformer
White
Blue
R
E
S
E
T
Black
1
2
3
4
5
P7
VAC Input Power
Interlock
Auxiliary
Common
Terminal
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4
3
2 1
Com
Green
Black
White
Red
NO
Black
Yellow
L3
Red
L2
Black
L1
4404-010
Black
Hot
White
Hot
NC
Hot
Board Ground
White
NO
Chassis
Ground
Blue
Yellow
Alarm Reset
Black
Black
48
White
Current
Sensor
Alarm
Red
9210-065-M-9-14
Model 9240 3 HP 3-Phase 208/230 VAC with Speed Controller
Shield
Ground
Shielded Cable
Orange
Red
Black
Gear Reducer
40:1
Blue
P/N 2600-348
L1
L2
Mode
1.5 ft/s
Limit Assembly
White Com
basic I/O control
42
43
46
47
B-
Blue
T1
T2
T3
U
V
W
B-
B+
NO
Partial
Open
Limit
Sensor
B+
Red
Black NO
White
Green NO
Blue
Yellow
Com
LMT
EXIT
LOOP
Red
Bottom
Slow Down
LOOP
REVERSE
Blue
Black
Com
115 VAC
Convenience
Outlets
LMT
AC Power
Red
Bottom Limit
Com
Limit
Switch
Plug P2
P8
White
1 2 3 4
ON
Red
TIME
DELAY
P6
Black
REV SENSE
CLOSE
Motor Plug P6
1 2 3 4 5 6 7 8
Red
REV SENSE
OPEN
Neutral
ON
Power
White
Top
Slow Down
Red
Black
Black
Top Limit
Com
1
2
5
6
11
12
2
14
13A
13B
13C
15
25
2
30
31
TXA
TXB
Red
Black
230 Step-Down
Transformer
White
AC Tech Brake
SCF series
2 ft/s
Yellow
0 ft/s
P/N 2600-404
Speed
Controller
1 ft/s
.5 ft/s
L3
2. 0
EPM
208 VAC
OR
230 VAC
208 VAC P/N 9210-416
230 VAC P/N 9210-417
Blue NO
Black
1
2
3
4
5
3 HP
Three Phase
Speed Controller
Red
Yellow NO
208 Step-Down
Transformer
White
1
2
3
4
5
Shield
Orange
Red
Black
White
Blue
P7
Interlock
NO
VAC Input Power
Auxiliary
Common
Terminal
20 19 18 17 16 15 14 13 12 11 10 9
8
7
6 5 4
3
2 1
Com
Black
White
Red
Green
Yellow
L3
Red
L2
Black
L1
4404-010
Black
Hot
White
Hot
NC
Hot
Board Ground
White
NO
Chassis
Ground
Blue
Yellow
Alarm Reset
White
Black
Black
Alarm
Current Sensor
Red
Black
Black
9210-065-M-9-14
49
Installation/Owner’s Manual
Series 9200
Heavy-Duty Vehicular Slide Gate Operator
Use this manual for circuit board 4404-010 Revision A or higher.
9210-065-M-9-14
www.doorking.com
DoorKing, Inc.
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
Phone: 310-645-0023
Fax: 310-641-1586
Copyright 2009 DoorKing, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising