Superthane and Urebrade Polyurethane Tubing and Hose in Ether

Superthane and Urebrade Polyurethane Tubing and Hose in Ether
123c
Polyurethane
P
olyurethane combines the best
properties of both plastic and
rubber. It offers abrasion and tear
resistance, high tensile and
elongation values, and low
compression set. Polyurethane is
naturally flexible and exhibits
virtually unlimited flexural
abilities.
Combining good
chemical resistance with
excellent weathering
characteristics sets
polyurethane apart
from most other
thermoplastics. It has
exceptional resistance
to most gasolines, oils,
kerosene, and other petroleumbased chemicals, making it an
ideal choice for fuel lines
(although additives in today’s
gasoline and petroleum products
warrant field testing).
The two basic formulations of
urethane, ester and ether, have
some important differences.
Water attacks ester-based
urethane, causing a significant
reduction in physical properties.
Ether urethanes exhibit far
superior hydrolytic stability,
especially in humid environments. Ether-based materials also
resist fungus growth better than
ester-based materials. ■
Superthane®
Transparent polyurethane
tubing . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Urebrade®
Transparent braid reinforced
polyurethane hose . . . . . . . . . . . . . . 4
Fluid Transfer Specialists ®
Applications
■ Abrasive Powder Transfer ■ Agriculture ■ Air Tools ■ Automated
Machinery ■ Automotive ■ Cement Slurries ■ Computer Disc Drive
Equipment ■ Fluid Circuitry ■ Fluid Feeds ■ Granular Transfer
■ Grease & Lubrication Lines ■ Hydraulic Control Systems ■
Instrumentation ■ Insulating Sleeves ■ Lubricated Air Feeds ■ Metering
Pumps ■ Oil & Fuel Lines ■ Oxygen & Gas Lines ■ Petroleum Products
Transfer ■ Pneumatic Control Systems ■ Pressure Measuring Devices
■ Robotics ■ Sensing Systems ■ Small Motor Fuel Lines ■ Transfer Lines
for Clean Liquids ■ Transfer Lines for Internal Contamination Fluids ■
Vacuum Equipment ■ Well Pipe and Cable Jacket ■ More
Sign up for our eNewsletter at www.newageindustries.com/extrusions
Superthane
123c
®
Tr a n s p a r e n t P o l y u r e t h a n e Tu b i n g
■ Available in Ester or Ether formulations
■ Both formulations made from non-toxic raw materials conforming to
FDA standards for use with wet and fatty food contact surfaces
■ Extremely resistant to weathering†, tearing, impact, radiation, and
abrasion
■ Transparent, flexible, resilient, tough; resistant to oils, greases,
and fuels††
■ Wide range of temperature resistance: -85°F to 185°F (ester)
■ Ether-based raw material is listed by the National Sanitation
Foundation (NSF 61) for use with potable water
■ Ester-based raw material is free of animal derived
components and REACH compliant
■ Free of DEHP, phthalates, BPA and conflict minerals
Made in U.S.A.
■ RoHS compliant
■ Can be heat sealed, coiled, fabricated, or bonded
Custom Services
Notes
†Hydrolytic Stability — For resistance to
moisture and fungi, SUPERTHANE ether is
recommended. (Ester polyurethane does not react
well with water, prolonged humid conditions, or
attack from fungi.) The raw material used in its
manufacture is listed by the National Sanitation
Foundation (NSF 61).
SUPERTHANE is much more resistant to
pressure and vacuum applications than
corresponding sizes of PVC or rubber.
††Although polyurethane is commonly used in
fuel applications, due to additives in today’s
gasoline and petroleum products, field testing
should be performed.
When used with Thermobarb® fittings,
SUPERTHANE will not require clamps, provided
that working pressures remain at or below 105 psi
at ambient temperature.
Custom coiled polyurethane is available — call
for details.
For easy identification, SUPERTHANE is
imprinted with the trademarked name.
■ Cut
■ Size
■ Color
■ Overbraid
■ Hot Bond
■ Heat-Form
■ Hardness
■ And More
Call for more information: 800-506-3924 or 215-526-2300
Recommended Fittings & Clamps
■ Thermobarb® barbed fittings
■ Cam operated couplings
■ Oetiker® ear type clamps
■ Kwik Clamp™ nylon double bond hose clamps
■ Worm gear clamps
Physical Properties**
Hardness, Shore A ±5
Tensile Strength, psi
Elongation at Break, %
Brittle Temperature, °F
Maximum Operating Temp., °F
ESTER
85
6100
490
-85
185
ETHER
85
7500
500
-85
175
**Values listed are typical for the material used in
manufacture, except where noted, and are meant only as
a guide to aid in design. Field testing should be
performed to find the actual values for your application.
2
www.newageindustries.com
Meet Some of NewAge Industries’ Owners
Through an Employee
Stock Ownership Plan
(ESOP), we’re part
owners in the company,
and that makes your
satisfaction an investment in our future.
Molly Doheny
Human Resources
Manager/Owner
3 years
Randy Decker
Graphic & Web
Designer/Owner
21 years
Bunna Soth
Silicone Molding/
Owner
9 years
Superthane
123c
®
Tr a n s p a r e n t P o l y u r e t h a n e Tu b i n g
PART NO.
ESTER
PART NO.
ETHER
ID
(IN.)
OD
(IN.)
WALL
(IN.)
STANDARD
LENGTH
(FT.)
WORKING
PSI AT
70°F
200 0075
210 0070
210 0070
210 0147
.063
.063
.125
.125
.125
.170
.188
.188
.250
.250
.250
.313
.313
.313
.375
.375
.375
.375
.438
.500
.500
.500
.500
.625
.625
.625
.750
.750
.875
1.000
1.000
1.500
2.000
.125
.125
.188
.188
.250
.250
.250
.313
.313
.375
.500
.438
.500
.563
.500
.500
.563
.625
.688
.625
.625
.688
.750
.750
.813
.875
.938
1.000
1.125
1.250
1.250
1.750
2.250
.031
.031
.031
.031
.063
.040
.031
.063
.031
.063
.125
.063
.094
.125
.063
.063
.094
.125
.125
.063
.063
.094
.125
.063
.094
.125
.094
.125
.125
.125
.125
.125
.125
100
500
100
1000
100, 1500
500
100
100, 1000
100
100, 1000
100
100
100
100
100
500
100
100
100
50
100
100
50, 100
100
100
100
100
50, 100
100
50
100
100
50
135
135
72
72
130
70
27
74
33
67
131
65
75
118
59
59
84
100
80
36
36
48
60
40
54
60
43
51
33
40
40
31
22
200
200
200
200
200
200
200
200
200
200
200
200
200
0152
0152
0229
0383
0460
0537
0768
0845
0999
1076
1153
1230
1307
200 1384
200 1461
200 1615
200 1692
200 1846
200 2000
200 2077
200 2231
200 2385
200 2539
210 0224
210
210
210
210
210
0455
0609
0686
0840
0917
210
210
210
210
1148
1148
1225
1302
210
210
210
210
210
210
210
210
210
210
210
210
210
210
1533
1533
1610
1687
1764
1841
1918
1995
2072
2226
2380
2380
2534
2688
LBS. PER
100 FT.
ESTER
.48
.79
.79
1.92
1.37
1.13
2.55
1.42
3.19
7.66
3.83
6.24
8.93
4.47
7.16
10.22
11.48
5.75
12.77
10.98
15.33
17.88
20.43
22.99
LBS. PER
100 FT.
ETHER
.45
.45
.74
1.77
2.38
1.33
2.98
7.15
3.57
4.17
4.17
6.68
9.54
5.36
5.36
8.47
11.92
6.56
10.25
14.30
12.03
16.69
19.07
21.46
21.46
30.99
40.53
Add length suffix to part number when ordering. Example: 100 ft. of .125” I.D. x .188” O.D. ester tubing is part number 200 0152-100.
Working pressures are calculated from burst testing using a 3:1 safety factor. Application testing is recommended.
Cut coils are available from coils of 100 ft. or less; charges apply — call for details. Coils over 100 ft. are sold by standard coil
length only. Due to the coil diameter, some larger sizes must ship via truck.
Tolerances: ID & OD ±3% but not less than ±.005".
BOLD indicates the critical dimension for fittings application.
More NewAge Industries’ Owners
www.newageindustries.com
Did you know . . . ?
We successfully undergo
multiple customer
audits each year.
Chris Boytim
Supplier Quality
Manager/ Owner
18 years
Nary Seng
Silicone Molding/
Owner
7 years
Jeremiah Brookins Peter Chao
Warehouse/Owner Silicone Manu1 year
facturing/Owner
16 years
Kathy Colon
Silicone Molding/
Owner
4 years
Dan Tropea
Director of Supply
Chain/Owner
1 year
3
Urebrade
123c
®
Tr a n s p a r e n t B r a i d R e i n f o r c e d P o l y u r e t h a n e H o s e
■ Open mesh polyester braiding incorporated within the wall of flexible,
ether-based polyurethane
■ Made from non-toxic raw ingredients conforming to FDA standards
■ Raw materials are listed by the National Sanitation Foundation
(NSF 61) for use with potable water
■ Offers much greater pressure capability than unreinforced
polyurethane tubing
■ Resistant to weathering†, tearing, impact, abrasion,
radiation exposure, oils, greases, and fuels††
■ Wide range of temperature resistance; -90°F to 175°F
Made in U.S.A.
■ Free of DEHP, phthalates, BPA and conflict minerals
■ RoHS compliant
■ Naturally transparent for visual contact with the flow
Notes
†Hydrolytic Stability — UREBRADE is
supplied in an ether formulation, making it
resistant to attack from moisture and fungi.
The raw materials used in UREBRADE are
listed by the National Sanitation Foundation
(NSF 61).
Where applications involve repeated
flexing, heavy vibration, or abrasion,
UREBRADE offers superior service life over
other materials.
Ester-based UREBRADE is available
through minimum order — call for details.
††Due to additives in today’s gasoline
and petroleum products, field testing should
be performed.
For easy identification, transparent
UREBRADE is imprinted with the
trademarked name.
Physical Properties**
Hardness, Shore A ±5
Tensile Strength, psi
Elongation at Break, %
Brittle Temperature, °F
Max. Operating Temperature, °F
PART NO.
ID
(IN.)
OD
(IN.)
WALL
(IN.)
STANDARD
LENGTH
(FT.)
220 0072
220 0149
220 0226
220 0303
220 0380
220 0457
220 0534
220 0611
220 0688
.250
.375
.500
.625
.750
1.000
1.250
1.500
2.000
.470
.630
.750
.905
1.025
1.300
1.710
1.930
2.500
.110
.127
.125
.140
.137
.150
.230
.215
.250
50, 100
50, 100
25, 50, 100
100
50, 100
25, 50, 100
50, 100
50, 100
100
WORKING BEND LBS. PER
PSI AT RADIUS 100 FT.
70°F
(IN.)
250
190
150
130
100
80
75
50
40
.750
.750
1.500
2.000
3.000
3.500
4.000
5.500
7.500
6.04
9.78
11.92
16.34
18.62
26.32
51.94
56.26
85.82
Add length suffix to part number when ordering. Example: 100 ft. of .250” I.D. x .470” O.D.
hose is part number 220 0072-100.
Working pressures are calculated from burst testing using a 4:1 safety factor. Application
testing is recommended.
Cut coils available; charges apply — call for details.
Due to the coil diameter, some larger sizes must ship via truck.
BOLD indicates the critical dimension for fittings application.
Custom Services
■ Cut
■ Size
■ Color
■ Overbraid
■ Hot Bond
■ Heat-Form
■ And More
Call for more information: 800-506-3924 or 215-526-2300
85
5500
580
-90
175
**Values listed are typical for the material used in
manufacture, except where noted, and are meant only as
a guide to aid in design. Field testing should be
performed to find the actual values for your application.
Recommended Fittings & Clamps
■ Thermobarb® barbed fittings
■ Cam operated couplings
■ Oetiker® ear type clamps
■ Kwik Clamp™ nylon double bond hose clamps
■ Worm gear clamps
Superthane, Urebrade, Kwik Clamp, Thermobarb, NewAge Industries, “Fluid Transfer Specialists” and The "N" Logo are trademarks of NewAge® Industries, Inc. • Oetiker reg. TM Oetiker, Inc.
WARRANTY: NewAge Industries’ products are warranted to be free from defects in material and workmanship. Any product found to carry such defects will be replaced without charge. This warranty is limited only to the replacement of NewAge Industries' products, item for item, which after examination
by NewAge Industries are deemed defective. NewAge Industries specifically disclaims any other liability. The data supplied is provided as a helpful guideline and is believed to be reliable; however, nothing stated shall constitute a guarantee, recommendation, or warranty for any application.
NOTICE: NewAge Industries, Inc. has been a privately owned corporation since 1954. Neither the corporation nor its principals are affiliated, in any way, with any other group or entity either representing themselves as or being referred to by the term New-Age.
© NewAge Industries, Inc. 2017
Specifications are subject to change without notice.
DISTRIBUTOR PARTNER
5/12/17
123c
145 James Way
Southampton, PA 18966
www.newageindustries.com
800-50-NEWAGE
(800-506-3924)
215-526-2300
Fax: 800-837-1856
215-526-2190
info@newageindustries.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising