VF-S150-XXA Series Datasheet - switching power supply | CUI Inc

VF-S150-XXA Series Datasheet - switching power supply | CUI Inc
For more information, please visit the product page.
rev.
page
1 of 5
date
11/2009
DESCRIPTION: switching power supply
PART NUMBER: VF-S150-XXA
features
·
·
·
·
·
·
·
·
·
ac input range auto-selectable
power factor correction
remote on/off
power good signal
short circuit protection
over load protection
over voltage protection
over temperature protection
providing Peak Power 600W within
500uS duty duration
· approved to UL, CUL, TUV, CE with CB
scheme
· high power density: 6.25 watts cu. in.
E210311
preset
MODEL
VF-S150-03A
VF-S150-05A
VF-S150-12A
VF-S150-18A
VF-S150-24A
VF-S150-48A
ripple & noise 3, 4
output current
output 1, 2
3 - 4 V
5 - 6 V
12 - 16 V
17 - 23 V
24 - 30 V
35 - 56 V
voltage
3.3V
5V
12V
18V
24V
48V
convection
20 A
20 A
8.33 A
5.56 A
4.17 A
2.08 A
16 CFM
30 A
30 A
12.5 A
8.33 A
6.25 A
3.13 A
max. power 5
120 W
150 W
150 W
150 W
150 W
150 W
regulation 4
+/- 1%
+/- 1%
+/- 1%
+/- 1%
+/- 1%
+/- 1%
(Vpp)
50 mV
50 mV
+/- 1%
+/- 1%
+/- 1%
+/- 1%
notes:
1 Output is fully isolated.
2 Output voltage is measured at output power connector.
3 1% minimum load is required to maintain the ripple and regulation.
4 Ripple and noise is measured from 10 kHz to 20 MHz at output terminals with a 0.1 μF ceramic and a 22 μF electrolytic capacitor in parallel.
5 Maximum power is 100 W with convection cooling except for VF-S150-03A where power is 80 W max.
CUSTOM CONFIG KEY
VF-S150- XX A- X X - CXX
Output voltage
Input/Output connector:
“blank” = Molex input / Molex output
1 = Terminal block input / Terminal block output
2 = Molex input / Terminal block output
3 = Terminal block input / Molex output
4 = IEC320 input / Molex output
5 = IEC320 input / Terminal block output
Reserved for custom
configurations
Low leakage option:
“blank” = standard specification
L = low leakage (contact factory)
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
www.v-infinity.com
For more information, please visit the product page.
rev.
PART NUMBER: VF-S150-XXA
page
2 of 5
date
11/2009
DESCRIPTION: switching power supply
INPUT
parameter
input frequency
input voltage
input current
inrush current
power factor
conditions/description
90-132 / 180-264 auto-selectable
At 115 VAC
At 230 VAC
peak measured at 115 VAC at full load, cold start
peak measured at 230 VACat full load, cold start
Passive Power Correction meets EN61000-3-2 class A
min
47
90/180
nom
max
63
132/264
4
2
35
70
units
Hz
VAC
A
A
A
A
min
nom
max
units
OUTPUT
parameter
transient response
overshoot
efficiency
turn on delay
hold up time
adjustability
LED display
power good
fan drive
conditions/description
Output voltage returns to within 1% in less than
2.5 mS for a 50% load change. Peak
transient does not exceed 5%.
Turn-on and turn-off overshoot shall not exceed
5% over nominal voltage.
Measured at 230 V and full load
3.3 V model:
70%
5 V model:
75%
12 V model:
80%
minimum for all other models:
83%
At 120 VAC
At 120 VAC and 80% of rated maximim load
20
Adjustable with built-in trim pot.
+/- 5%
When green (LED1) is on the power supply is operating normally.
Designated as PG on the CN1. This signal
goes high 100-500 mS after the output reaches regulation.
It goes low at least 1 mS before loss of regulation.
12 VDC/300mA for external fan
1
second
ms
PROTECTION CIRCUIT
parameter
input fuse
overload
short circuit
output over-voltage
over temp.
conditions/description
Built-in ac fuse. A blown fuse usually indicates permanent
damage to the power supply serviceable by factory only.
Current limiting starts at 110-140% of the rated output current in foldback mode and
recovers automatically.
Short circuit can be continuous. Recovers automatically upon removal of short.
Output is protected agaist overvoltage. Unit shuts down and latches
when voltage at output terminals exceeds 130%. AC input needs to be
reset to restart the power supply.
Power supply shuts down when temperature is in excess of 85 ºC. Auto recovery.
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
www.v-infinity.com
For more information, please visit the product page.
rev.
PART NUMBER: VF-S150-XXA
page
3 of 5
date
11/2009
DESCRIPTION: switching power supply
GENERAL AND SAFETY
parameter
operating temp.
conditions/description
Derates linearly from 100% load at 50°C to
50% load at 70ºC.
storage temp.
operating humid.
storage humid.
EMI
-20
Non-condensing
5%
Non-condensing
5%
CISPR 22/EN55022 class B, EN61000-3-2, 3,
EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024 CE marked (LVD)
UL60950(E222889), CSA C22.2 No. 60950, TUV EN60950 and CB
240VAC
safety
leakage Current
switching frequency
vibration
isolation voltage
(HI-POT)
grounding test
warranty
MTBF
burn-in
remote on/off
min
0
nom
max
70
units
ºC
85
90%
95%
ºC
RH
RH
1.5
50
mA
Hz
Hz
0.1
VAC
VAC
VAC
Ω
25K
Acceleration ± 7.35 M/(SxS), on X, Y and Z Axis
Applied for 3 seconds at 10 mA max.
Primary to secondary:
Primary to transformer core:
Primary to chassis:
Allowable resistance measured when 25 A current is
applied from the ground pin of the three prong plug
to the farthest earthed connection point.
Standard warranty length
According to MIL-HDBK-217 at 30 ºC
Full load, at 45 ± 5 ºC, 230 VAC.
Designated as RMSW on the CN1, requires a low signal
to inhibit ouput. Hiccough mode.
5
3000
1500
1500
2
100,000
1
years
hours
hours
MECHANICAL
parameter
weight
enclosure
conditions/description
min
nom
max
400
5(L) x 3.2(W) x 1.5(H)
units
grams
inches
LOGIC CONNECTOR - (CN1)
parameter
logic
pin assignments:
conditions/description
JS B7B-XH-A
Suggested mating connector: JST XHP-3 or equivalent (CHYAO SHIUNN JS-2001-03)
1. Power good
2. Remote switch
3. RTN
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
www.v-infinity.com
For more information, please visit the product page.
rev.
PART NUMBER: VF-S150-XXA
page
4 of 5
date
11/2009
DESCRIPTION: switching power supply
FAN DRIVER CONNECTOR - (FAN)
parameter
fan
conditions/description
Suggested mating connector: JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02)
OUTPUT CONNECTOR - (CN2)
parameter
output (option 1)
output (option 2)
conditions/description
Molex Part No. 26-48-1061 or similar (6 pin)
Output pin assignment, V+ (Pins 1-3), V- (Pins 4-6)
Suggested mating connector: Molex Part No. 09-91-0600 or equivalent (6)
Howder Terminal block Part No. HD-601-4P (4 pin, M3.5 Screw) 6.35 mm spacing
Output pin assignment, V+ (Pins 1-2), V- (Pins 3-4)
Suggested mating connector: Molex 19198-0045 or similar
INPUT CONNECTOR - (CN3)
parameter
AC input (option 1)
AC input (option 2)
conditions/description
Molex Part No. 26-48-1051 or similar (5 pin, 3 used).
Suggested mating plug: Molex Part No. 09-91-0500 or equivalent (5 pin, 3 used)
Howder Terminal block Part No. HD-601-3P (3 pin, M3.5 Screw) 6.35 mm spacing
Suggested mating connector: Molex 19198-0045 or similar
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
www.v-infinity.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising