te-tccmos te-tccmos - iBEAM, Vehicle Safety Systems

te-tccmos te-tccmos - iBEAM, Vehicle Safety Systems
TE-TCCMOS
Product Manual
800.221.0932
iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
TE-TCCMOS
Product Manual
800.221.0932
iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
I. Specifications
II. Connection
Parking assist line disable loop
SENSOR
CMOS II
Effective Pixel
656 X 492
Horizontal Sync Frequency
15625KHZ
Vertical Sync Frequency
PAL50HZ / NTSC 60HZ
Scanning System
2 : 1 Interlace
Sync System
Internal
AGC
Auto
BLC
Auto
2) Connect the RED wire to the +12 volt reverse wire
Resolution
420 TV Lines
3) Connect the BLACK wire to ground (a metal, non-painted surface).
S/N Ratio
More Than 48dB
4) Run video cable though vehicle, up to video display. (Avoid placing video
cable where it can get pinched or damaged).
Current Consumption
No More 150mA
Power Supply
DC12V ± 10%
Operating Temperature
-22°
Storage Tempurature
~ 176° F
-40° ~ 176° F
Viewing Angle
150°
Water-Proof
IP67
Minimum Illumination
0.5Lux/F1.2(0Lux with LED)
I. Specifications
RED
BLACK
Video (in)
1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that
might damage the vehicle. When all connections have been made and before
mounting the camera, verify the camera is working and has good view of the
area. Then mount the camera down with screws.
5) Attach the YELLOW video rca to camera’s output and to the reverse camera
input of the radio or video display.
NOTE: The camera comes with the parking assist lines. If you want to remove the
parking lines follow the steps below:
A) Disconnect power to the camera
B) Cut the WHITE loop to remove the parking assist lines, isolate and tape the wires
C) Reconnect power to the camera
If the parking assist lines are wanted just follow the steps above and reconnect
the wires.
II. Connection
Parking assist line disable loop
SENSOR
CMOS II
Effective Pixel
656 X 492
Horizontal Sync Frequency
15625KHZ
Vertical Sync Frequency
PAL50HZ / NTSC 60HZ
Scanning System
2 : 1 Interlace
Sync System
Internal
AGC
Auto
1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that
might damage the vehicle. When all connections have been made and before
mounting the camera, verify the camera is working and has good view of the
area. Then mount the camera down with screws.
BLC
Auto
2) Connect the RED wire to the +12 volt reverse wire
Resolution
420 TV Lines
3) Connect the BLACK wire to ground (a metal, non-painted surface).
S/N Ratio
More Than 48dB
4) Run video cable though vehicle, up to video display. (Avoid placing video
cable where it can get pinched or damaged).
Current Consumption
No More 150mA
Power Supply
DC12V ± 10%
Operating Temperature
-22°
Storage Tempurature
~ 176° F
-40° ~ 176° F
Viewing Angle
150°
Water-Proof
IP67
Minimum Illumination
0.5Lux/F1.2(0Lux with LED)
RED
BLACK
Video (in)
5) Attach the YELLOW video rca to camera’s output and to the reverse camera
input of the radio or video display.
NOTE: The camera comes with the parking assist lines. If you want to remove the
parking lines follow the steps below:
A) Disconnect power to the camera
B) Cut the WHITE loop to remove the parking assist lines, isolate and tape the wires
C) Reconnect power to the camera
If the parking assist lines are wanted just follow the steps above and reconnect
the wires.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising