92968066 500943 IN 0.0
PANEL CONNECTION BLOCK
to dome and door jamb switches
from 500942 bag "D"
HEADLTS
14
15
3
(12V BATTERY)
RED/YELLOW
ORANGE
(PARK LIGHTS)
BROWN
(PARK LIGHTS)
see detail "A"
BROWN
YELLOW/RED
(PARK LIGHTS)
(DIMMER SW FEED)
BROWN
right
tail light
(12V BATTERY)
GREEN/YELLOW
left
tail light
WHITE/BLACK
license plate
light
to grey lamp wire
from 500353 bag "E"
GREEN/YELLOW
(HEADLIGHT HI)
to light green hi beam indicator
lamp from 500353 bag "E"
GREEN/YELLOW
(HI BEAM IND)
YELLOW/GREEN
(PARK LIGHTS)
GAUGES
13
BROWN
HORN OUT
12
(HEADLIGHT LO)
HORN SW
11
YELLOW/GREEN
PARK
10
(HEADLIGHT LO)
BAT 2
9
Right
Headlight
YELLOW/GREEN
STOP/CRTSY
8
BLACK (GROUND)
BAT 3
7
Left
Headlight
HEADLIGHT
CONNECTOR
BLACK (GROUND)
TURN SW
6
left
parking
light
(HEADLIGHT HI)
HAZARD
HIGHWAY 15 NOSTALGIA WIRING KIT
( right side )
right
parking
light
(HEADLIGHT LO)
YELLOW/GREEN
4
GREEN/YELLOW
black
DETAIL "A"
150 Heller Pl #17 W - Bellmawr, NJ 08031 - 856-933-0801
PAGE 1
500943 C
DESCRIPTION:
NOTICE !!!
All connector drawings are shown viewing the
connector from the FRONT, and plugging wire in
from REAR
PART #
insert
Yellow / Red
wire in this cavity
GM COLUMN MOUNT
DASH MOUNT
UNIVERSAL
HEADLIGHT SWITCH KIT
92968066 instruction sheet
Rev 0.0
5/18/2009
HIGHWAY 15 NOSTALGIA WIRING KIT
INSTALLATION INSTRUCTIONS:
WIRE COLOR
CIRCUIT
INSTALLATION PROCEDURE
WHITE/BLACK
DOME/CTSY LT GROUND
BROWN
PARKING LAMP FEED
BROWN
REAR RUNNING LIGHT
BROWN
LICENSE PLATE LIGHT
RED/YELLOW
YELLOW/RED
BAT FEED TO HEADLIGHT
SWITCH
DIMMER SWITCH FEED
Route this wire to your dome light assembly and door jamb switches. This is a ground wire which activates
interior lights. If dome or courtesy lights are not being used, remove this wire from the headlight switch
connector.
Route this wire from the headlight switch connector #3 to one of the front parking lights. Cut this wire to length.
Double this wire with the cut cut off portion and route the loose end to the other parking light. Universal light socket
button terminals "E" are provided for those light sockets using this type of contact terminal.
Route this wire from the headlight switch connector #3 to one of the rear tail lights. Cut this wire to length. Double
this wire with the cut cut off portion and route the loose end to the other rear tail light. Universal light socket
button terminals "E" are provided for those light sockets using this type of contact terminal.
Splice in or double this loose piece wire with the single "BROWN" wire at the rear tail light connection from above.
Route the other (loose) end of this wire to the license plate light connection.
Route this wire to the fuse panel and install in the "HEADLTS" location.
ORANGE
GRAY/WHITE
PARK LIGHT 12V FEED
INSTRUMENT LAMP FEED
Route this wire to your dimmer switch connector #4. Cut to length, install terminal "D", and plug into the
location shown on page 1.
Route this wire to the fuse panel and install in the "PARK LTS" location.
Connect this wire to the instrument lamps, as shown in 500939 kit, bag “E”.
DIMMER SWITCH CONNECTOR #4 Plug this connector into your dimmer switch.
GREEN/YELLOW
(heavy gauge)
HI BEAM
GREEN/YELLOW
(thin gauge)
YELLOW/GREEN
HI BEAM INDICATOR LIGHT
LO BEAM
BLACK WIRES
HEADLIGHT GROUNDS
Route this wire from your dimmer switch to one headlight. Cut this wire to length, double this wire with the cut
off portion using terminal "C" and plug into the headlight connector "A" in the location shown on page 1.
Route the cut off wire to the other headlight, install terminal "B" and plug into the headlight connector "A"
in the location shown on page 1.
Connect this wire to the high beam indicator lamp connection from 500939 bag "E".
Route this wire from your dimmer switch to one headlight. Cut this wire to length and double this wire with the
cut off portion, using terminal "C" and plug into connector "A" in the location shown on page 1. Route the
cut off wire to the other headlight, install the supplied terminal "B" and plug into the headlight connector in
the location shownon page 1.
Attach a ring terminal and loose black wire assembly to a good ground. Route the other end of the wire to the
headlight assembly, cut to length, and install single terminal “B” and plug into connector “A” in the location
shown on page 1. Repeat this process for the opposite headlight assembly.
500943
A
PAGE 2
B
C
D
E
HEADLIGHT SWITCH
92968066 instruction sheet
Rev 0.0
5/18/2009
BROWN
left
parking
light
Left
Headlight
HEADLIGHT
CONNECTOR
GREEN/YELLOW
(HI BEAM IND)
(HEADLIGHT LO)
YELLOW/GREEN
to light green hi beam indicator
lamp from 500939 bag "E"
(HEADLIGHT LO)
GREEN/YELLOW
(PARK LIGHTS)
BROWN
BLACK (GROUND)
license plate
light
to grey lamp wire
from 500939 bag "E"
YELLOW/RED
(PARK LIGHTS)
right
tail light
(PARK LIGHTS)
(DIMMER SW FEED)
BROWN
BLACK (GROUND)
(HEADLIGHT HI)
left
tail light
BROWN
SPECIAL HEADLIGHT WIRING
see detail "A"
3
Right
Headlight
right
parking
light
YELLOW/GREEN
YELLOW/GREEN
BROWN
4
PART #
GREEN/YELLOW
black
DETAIL "A"
NOTICE !!!
All connector drawings are shown viewing the
connector from the FRONT, and plugging wire in
from REAR
PAGE 3
500943 C
DESCRIPTION:
insert
YELLOW/RED
wire here
HEADLIGHT SWITCH KIT
92968066 instruction sheet
Rev 0.0
5/18/2009
INSTALLATION INSTRUCTIONS:
WIRE COLOR
CIRCUIT
SPECIAL HEADLIGHT WIRING
BROWN
GREEN/YELLOW
(heavy gauge)
HI BEAM
YELLOW/GREEN
LO BEAM
BLACK WIRES
HEADLIGHT GROUNDS
INSTALLATION PROCEDURE
The connections to the front end of open roadster cars with exposed headlights and parking / directional lights
do not follow the installation procedure explained on Page 2. The following alternative installation procedure
can be used for these vehicles.
Route this wire from your headlight switch to the left hand parking light assembly. Cut this wire to length and install
in the parking light assembly. Take the remaining wire and route it to the right hand parking light assembly.
Cut to length and install in the right hand parking light assembly. Select a point under the dash where the
parking light wires and the main lead from the headlight switch can be joined in an in-line splice.
Route this wire from your dimmer switch to the left hand headlight connector. Cut this wire to length, install
a single wire terminal "B" and plug into the headlight connector "A" in the location shown on page 1.
Take the remaining wire, install a single wire terminal "B" and plug into the right hand headlight connector "A"
as shown on page 1. Select a point under the dash where the headlight wires can be joined in an in-line
splice. This point can be at the dimmer switch connection or at a convenient point before the final connection
to the dimmer switch.
Route this wire from your dimmer switch to the left hand headlight connector. Cut this wire to length, install
a single wire terminal "B" and plug into the headlight connector "A" in the location shown on page 1.
Take the remaining wire, install a single wire terminal "B" and plug into the right hand headlight connector "A"
as shown on page 1. Select a point under the dash where the headlight wires can be joined in an in-line
splice. This point can be at the dimmer switch connection or at a convenient point before the final connection
to the dimmer switch.
Attach a ring terminal and loose black wire assembly to a good ground. Route the other end of the wire to the
headlight assembly, cut to length, and install single terminal “B” and plug into connector “A” in the location
shown on page 1. Repeat this process for the opposite headlight assembly.
A
B
C
D
E
500943
HEADLIGHT SWITCH
PAGE 4
92968066 instruction sheet
Rev 0.0
5/18/2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising