CPP7510 - Cobra Electronics Corporation

CPP7510 - Cobra Electronics Corporation
The Cobra line of quality products includes:
CB Radios
Dash Cams
User Manual
Radar Detectors
Marine VHF Radios
Power Inverters
Portable Power - Anytime, Anywhere!
Thank you for purchasing the Cobra CPP7510 JumPack™
portable jump starter PowerPack. Before using this
product, please read these instructions carefully to learn
about the features and capabilities of the JumPack and
how to get the best performance.
Note: Please charge your CPP7510 JumPack completely
prior to using it for the first time.
©2016 Cobra Electronics Corp. Part No. 480-1075-P Printed in China Version A
Charge the JumPack fully prior to use.
Precautions when working with the JumPack:
WARNING: Keep the unit clear of fire and water.
WARNING: Shock Hazard. Keep away from children. Do not
insert foreign objects into the Jump Start Cable Input, the
USB Output Port, or the Charge Adapter Input Jack. Do not
expose this product to water, rain, snow, condensation, or
spray. Do not open the JumPack to replace the internal
battery. No user replaceable parts are inside the JumPack.
WARNING: Explosion Hazard. Do not use this product where
there are flammable fumes or gases, such as an inadequately
vented bilge of a boat, or near propane tanks. Do not use this
product in an enclosure containing automotive-type lead-acid
The Jump Start Cable clamps must be connected positive to
positive (red clamp to battery [+]) and negative to negative
(black clamp to battery [-]).
WARNING: Fire Hazard
Do not crush or puncture the JumPack. Never allow the Jump
Start Cable’s red and black clamps’ metal contacts to touch each
other or another common metal conductor. This could cause
damage to the unit and/or create a fire hazard. The jump start
feature is designed only for starting vehicles, and Jump Start
Cables must be disconnected from the vehicle's battery and from
the JumPack once the vehicle starts.
When jump starting a vehicle with the JumPack, turn the ignition
key for no more than 3 seconds at a time.
Amp Output
Charge Level Button
5V 3A
Battery Status Indicator
Light Bar
Charge Adapter
Input Jack
Jump Start
Cable Input
AC Adapter
Car Adapter
Recharging the JumPack:
The CPP7510 JumPack can be recharged with the supplied Car
Adapter or with the supplied AC Adapter.
When the CPP7510 is charging, the light bar will show the current
battery charge level. The last section of the light bar that is lit will blink
to show that the JumPack is charging. When the JumPack is fully
charged the light bar will turn off automatically.
For best battery performance the JumPack should be fully
recharged every 3 months.
5V 3A
Check Battery Charge Level:
To check the battery charge level of the JumPack press the
button on the top of the unit with no device connected.
The green light bar will show the remaining battery charge level:
LED Flashlight
Jump Start Cable
with Clamps
Caution: Operating temperature
Do not expose the JumPack to temperatures over +113° F (+45° C) or
under -14° F (-10° C). Using the JumPack at high or low temperatures
may reduce the internal battery capacity and shorten the battery life.
Note: In extreme cold weather conditions, please store the
JumPack indoors for best results.
The JumPack is supplied with a rechargeable Li-Cobalt battery.
This battery is self-contained and not consumer replaceable. Battery must
be disposed of properly when it no longer holds a charge. Proper
charging practices will increase the life of the batteries. For information
on battery recycling call toll free 800-822-8837.
Precautions when working with vehicle batteries:
WARNING: Explosion and fire hazard
1. Follow all instructions published by the battery manufacturer and the
manufacturer of the equipment in which the battery is installed.
2. Make sure the area around the battery is well-ventilated.
3. Never smoke or allow a spark or flame in the vicinity of the
engine or batteries.
4. Be careful not to drop a metal object on the battery or allow a
metal tool to simultaneously touch the positive and negative
cable ends or battery terminals.
5. Remove personal metal items such as rings, bracelets,
necklaces, and watches when working with batteries. Batteries
produce a short-circuit current high enough to weld a ring or
other similar objects to metal, causing a severe burn.
6. If you need to remove a battery, always remove the negative
terminal from the battery first. Make sure all accessories are
off to prevent causing a spark.
7. Someone should be within range of your voice, or close enough
to come to your aid when you work near batteries.
8. Have plenty of fresh water, soap and a supply of baking soda on
hand in the area of the batteries in case of contact with battery
acid. Baking soda neutralizes lead acid battery electrolyte.
Battery Status Indicator
Light Bar
1st Section on: 10%-40% charge
2nd Section on: 40%-65% charge
3rd Section on: 65%-85% charge
4th Section on: 85%-100% charge
Note: When charging a device the section light may decrease
because the JumPack cannot accurately measure the capacity
during rapid charging. To confirm the actual battery charge level,
disconnect the device being charged and press the
Flashlight/Battery Charge Level Button.
Checking the Fuse:
The Jump Start Cables are designed with an in-line fuse to protect
the Jumpack in the event of an over-load condition. The Jump Start
Cables include a clear case to that the in-line fuse is intact:
Starting a Vehicle:
1. Make sure the JumPack is fully charged.
2. Turn off all the accessories on the vehicle.
3. Connect the RED clamp to the POSITIVE post of the battery.
4. Connect the BLACK clamp to the NEGATIVE post of the battery.
5. Connect the Jump Start Cable into the Jump Start Cable Input.
Be sure that the plug is firmly pressed into the JumPack.
Fuse Intact
6. Turn the ignition key to start the vehicle. Do not crank the
ignition for more than 3 SECONDS at a time.
7. If the vehicle does not start on the first try, WAIT FOR
1 MINUTE before trying to start the vehicle again.
NOTE: If your vehicle does not start after 3 attempts, consult
with a mechanic.
If the engine starts:
8. Immediately disconnect the Jump Start Cable from the
JumPack, then from the battery posts.
Open or Damaged Fuse
CAUTION: Do not use the Jump Start Cables if the fuse appears
to opened or damaged. For any questions, please call 773-889-3087
for assistance or visit us online at: www.cobra.com
9. Leave the engine running for at least twenty minutes to
allow the vehicle’s battery to recharge.
Starting a Vehicle continued:
NOTES: The JumPack is designed for gasoline powered
passenger cars in good working order and with batteries that are
not damaged but require assistance commonly due to leaving
lights on, cold temperature, or sitting unused for limited periods
of time.
The JumPack jump starter uses a special high current battery
to provide up to 400 peak amps to start your engine. It can
provide 200 amps starting current to jump start up to 3 cars on
one charge. After this, the unit must be recharged.
The JumPack is intended to jump start a vehicle with a
battery that is not completely discharged.
Charging a 5V USB Device:
To charge a 5V USB device, connect the device’s cable to the
JumPack’s USB output.
The JumPack will turn on and start charging the device
automatically. The green light bar will indicate the device
is charging.
LED Flashlight:
Press the Flashlight/Battery/Charge Level Button for 3 seconds to
turn on the LED flashlight. Press again to activate the strobe
function. Press again to activate the SOS function. Press again to
turn Off.
Product Features:
• Lithium Cobalt rechargeable battery.
• 200 Amp Starting Current / 400 Amp Peak Current.
• 5V/3 Amp USB Output for rapid charging of portable devices.
• High Intensity work LED light, strobe and SOS .
• Rechargeable by car adapter, or 120 VAC Wall Adapter.
Product Specification:
• Li-Cobalt rechargeable battery: 11.1V/28Wh
• Size:
5.03” x 2.87” x 0.98”
(128mm x 73mm x 25mm)
• Weight:
10.58 oz. (300g.)
• Recharge times:
car or home - 4 hours
• Starting/Peak Current:
200 Amps/400 Amps
• USB Output:
3 Amps
Once the device reaches its charge capacity and ceases charging,
the light bar will turn off.
5V 3A
5V 3A
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician
for help.
WARNING: Any modifications made to this device that are not expressly
approved by party responsible for compliance could void the user’s
authority to operate this device.
Cobra® and the snake design are registered trademarks of
Cobra Electronics Corporation, USA.
Cobra Electronics Corporation™ is a trademark of Cobra
Electronics Corporation, USA.
PROPOSITION 65 WARNING: This product contains a chemical known to
the State of California to cause cancer and birth defects or other
reproductive harm.
Limited 1-Year Warranty:
For Products Purchased in the U.S.A.
Cobra Electronics Corporation warrants that its Cobra CPP7510
JumPack Charger, and the component parts thereof, will be free of defects
in workmanship and materials for a period of one year from the date of first
consumer purchase. This warranty may be enforced by the first consumer
purchaser, provided that the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, defective
products or component parts within the warranty period upon delivery to
the Cobra Factory Service Department, accompanied by proof of the date
of first consumer purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product
for warranty service, but the return charges will be at Cobra’s expense,
if the product is repaired, this warranty gives you specific rights, and
you may also have other rights which vary from state to state.
Exclusions: This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product, or as a result of
unauthorized alterations or repairs.
3. If the serial number has been altered, defaced or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and
fitness for a particular purpose are limited in duration to the length of
this warranty.
Cobra shall not be liable for any incidental, consequential or other
damages; including, without limitation, damages resulting from loss of
use or cost of installation.
Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you.
For Products Purchased Outside The U.S.A.
Please contact your local dealer for warranty information.
Product Service:
For any questions about operating or installing this new Cobra
product, or if parts are missing…PLEASE CALL COBRA
FIRST…do not return this product to the store. If this product
should require factory service, please call Cobra before sending the
product. This will ensure the fastest turn-around time on any repair.
If Cobra asks that the product be sent to its factory, the following
must be furnished to have the product serviced and returned:
1. For Warranty Repair include some form of proof-of-purchase,
such as a mechanical reproduction or carbon of a sales receipt.
Make sure the date of purchase and product model number are
clearly readable. If the originals are sent, they cannot be returned;
2. Send the entire product;
3. Enclose a description of what is happening with the product.
Include a typed or clearly printed name and address of where
the product is to be returned, with phone number (required
for shipment);
4. Pack product securely to prevent damage in transit. If possible,
use the original packing material;
5. Ship prepaid and insured by way of a traceable carrier such as
United Parcel Service (UPS) or Priority Mail with delivery
confirmation to avoid loss in transit to: Cobra Factory Service,
Cobra Electronics Corporation, 6500 West Cortland Street,
Chicago, Illinois 60707 U.S.A.;
6. If the product is in warranty, upon receipt of the product it will
either be repaired or exchanged depending on the model.
Please allow approximately 3 – 4 weeks before contacting Cobra
for status. If the product is out of warranty, a letter will
automatically be sent with information as to the repair charge or
replacement charge.
For any questions, please call 773-889-3087 for assistance or visit
us online at: www.cobra.com
Customer Support & Trademarks:
Customer Support
Should there be any problems with this product or further information
needed on its features please visit www.cobra.com for support, frequently
asked questions, Declarations of Conformity, and the electronic manual.
Waste Electrical and Electronic Equipment Information
This product has required the extraction and use of natural resources for
its production. It may contain hazardous substances that could impact
health and the environment, if not properly disposed. In order to avoid
the dissemination of those substances in our environment and to
diminish the pressure on the natural resources, we encourage you to use
the appropriate take-back systems for product disposal. Those systems
will reuse or recycle most of the materials of the product you are disposing
in a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you
to use the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse and recycling
systems, please contact your local or regional waste administration.
You may also contact your supplier for more information on the
environmental performances of this product.
The product label is located on the bottom of the unit.
Trademark Statement
Cobra, JumPack and the snake design are proprietary trademarks of
Cobra Electronics Corporation, USA.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF