2013
INSTALLATION
INSTRUCTIONS
PARTS LIST
Accessory
Application
FRONT LOWER TRIM
P/N 08P46-T0A-100
2013 CR-V
Publications No.
AII 13140
Issue Date
AUG 2012
TOOL AND SUPPLIES REQUIRED
Phillips screwdriver
Hex wrench
Front lower trim
Drill
3 mm, 5 mm, 8 mm, and 13 mm Drill bits
Pushpin
Eye protection (face shield, safety goggles, etc.)
Ruler
Tape
4
Bolts
Torque wrench
Rigid rack
3
Small well nuts
The following tool is available through the Honda Tool and
Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter
the number under “Search.” Or call 888-424-6857.
• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Front Lower Trim Installed on the
Vehicle
4
Large well nuts
3
Washer-screws
2
Clips
FRONT LOWER
TRIM
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
AII 47363 (1208)
Q0D2212AD
08P46-T0A-1000-90
1 of 4
INSTALLATION
2.
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
Position the front lower trim on the front bumper, and
install the front lower trim with the two clips removed
in step 1.
FRONT
BUMPER
NOTE: Be careful not to damage the paint finish.
1.
With the vehicle on a lift, remove the two center clips
from the front bumper.
FRONT
BUMPER
FRONT
FRONT LOWER
TRIM
CLIPS
Removed
in step 1.
3.
Using a pushpin, pierce the front bumper through the
seven holes in the front lower trim.
FRONT
FRONT
BUMPER
CLIP
Q0D2202BD
FRONT
LOWER
7 HOLES
TRIM
Pierce
FRONT
perpendicularly.
BUMPER
Q0D2201BD
PUSHPIN
FRONT
PUSHPIN
4.
2 of 4
AII 47363 (1208)
Q0D2203CD
Remove the front lower trim (two clips).
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
5.
While wearing eye protection, drill the four outboard
pierced marks to 13 mm. First drill with a 3 mm drill
bit, then with a 5 mm drill bit, then with an 8 mm, and
finish with a 13 mm drill bit.
6.
While wearing eye protection, drill the three inboard
pierced marks to 8 mm. First drill with a 3 mm drill bit,
then with a 5 mm drill bit, and finish with an 8 mm drill
bit.
•
Wrap tape around each drill bit 10 mm away
from the tip or use a drill stop.
•
Wrap tape around each drill bit 10 mm away
from the tip or use a drill stop.
•
Remove all burrs.
•
Remove all burrs.
DRILL FRONT
BUMPER
BIT
Drill
DRILL FRONT
BUMPER perpendicularly.
BIT
Drill
perpendicularly.
10 mm
(0.4 in.)
10 mm
(0.4 in.)
FRONT
BUMPER
OUTBOARD
PIERCED
MARK
FRONT
BUMPER
DRILL
TAPE
DRILL
TAPE
OUTBOARD
PIERCED MARK
INBOARD
PIERCED MARK
FRONT
FRONT
3 mm 5 mm
8 mm
13 mm
DRILL BITS
DRILL
3 mm
5 mm
8 mm DRILL BITS
Q0D2207BD
7.
DRILL
Q0D2208BD
Install one large well nut into each 13 mm outboard
hole. Install one small well nut into each 8 mm
inboard hole.
4 LARGE WELL NUTS
Install one well nut
into each 13 mm hole.
FRONT
BUMPER
FRONT
SMALL WELL NUTS
Install one well nut into
each 8 mm hole.
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
AII 47363 (1208)
Q0D2209BD
3 of 4
8.
While wearing eye protection, drill the inboard holes
in the front lower trim using a 5 mm drill bit. Remove
all burrs. Do not drill the two clip installation holes.
10. Position the front lower trim on the front bumper, and
install it with two new clips. Make sure the rubber
molding is not twisted or rolled under the front lower
trim.
FRONT LOWER
TRIM
INBOARD
HOLES
RUBBER MOLDING
(Not twisted or rolled under)
FRONT
BUMPER
5 mm
DRILL BIT
DRILL
Q0D2205AD
9.
While wearing eye protection, drill the four outboard
holes to 8 mm. First drill with a 5 mm drill bit, and
finish with an 8 mm drill bit. Remove all burrs.
FRONT
FRONT LOWER
TRIM
OUTBOARD
HOLE
OUTBOARD
HOLE
FRONT LOWER
TRIM
NEW CLIP
Q0D2210BD
11. Install one washer-screw into each 8 mm well nut
in the order
. Torque the washer-screws to
0.4 N·m (0.3 lbf·ft).
FRONT LOWER
TRIM
FRONT
BUMPER
5 mm
8 mm
DRILL BITS
Press.
DRILL
4 BOLTS
Q0D2204AD
2
1
Press.
2
FRONT
WASHERSCREWS
Q0D2211CD
12. Install one bolt into each outboard 13 mm well nut
and torque each bolt to 1.0 N·m (0.7 lbf·ft). Press the
front lower trim against the front bumper when
tightening the bolts on each side.
4 of 4
AII 47363 (1208)
© 2012 American Honda Motor Co., Inc. – All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising