Power Flood 44-6 4 in 1 RGBW IP20

Power Flood 44-6 4 in 1 RGBW IP20
Power Flood 44-6 4 in 1 RGBW
IP20
1
INTRODUCTION
Thank you for having chosen our LED lighting
Unpack the device, inside the box you should find:
The fixture device
One power cable
One XLR connection cable
This manual
Please check carefully that there is no damage caused by
transportation. Should there be any problems, consult your dealer and
don’t install this device.
DESCRIPTION
Features

Easy multi fixture hanging system, outdoor version available

44pcs RGBW 4in1 LED, no ultraviolet radiation

More than 50,000 hours for the LED light source

12,000 lm

35 degree

1/3/4/5/10/14/15 DMX channels

16 Bit Dimmer

DMX Mode /Master-slave mode

AC 100-240V 50/60Hz 260W

Diecasting heatsink, convection cooling, no fans, no noise

With temperature sensor to extend the lamp life

7000 Hz LED scan rate

L: 490mm H:285mm W:105mm, Weight 9Kg

IP65/IP43 selectable
SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to
maintain this condition and to ensure a safe operation, it
is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
This device falls under protection-class I. Therefore it is essential that
the device should be earthed.
The electric connection must carry out by qualified person.
If the external flexible cable or cord of this luminaire is damaged,
2
it shall be exclusively replaced by the manufacturer or his
service agent or a similar qualified person in order to avoid a hazard.
Make sure that the available voltage is not higher than stated at the
end of this manual.
Make sure the power cord is never crimped or damaged by sharp
edges.
If this would be the case, replacement of the cable must be done by
an authorized dealer.
Always disconnect from the mains, when the device is not in use or
before cleaning it. Only handle the power cord by the plug. Never
pull out the plug by tugging the power cord.
Never look directly into the light source, as
sensitive persons may suffer an epileptic shock.
Important:
Damages caused by the disregard of this user manual are not
subject to warranty. The dealer will not accept liability for any
resulting defects or problems.
DMX-512 control connection
The product has a DMX 512 input fitted with 3-pin XLR connectors.
Screened cables in compliance with EIA RS-485 specifications and the
following characteristics must be used for connections:
- 2 conductors plus screen
- 120Ohm impedance
- low capacitance
- max. transmission rate 250kBaud.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is
in an electrically noisy environment,such as in a discotheque, it is
recommended to use a DMX terminator. This helps in preventing
corruption of the digital control signal by electrical noise. The DMX
terminator is simply an XLR plug with a 120 OHM resistor connected
between pins 2 and 3,which is then plugged into the output XLR
socket of the last fixture in the chain.
3
Display Menu
Main menu
address
config
System Info
Color Menu
White Balance
Static color
Auto Test
Load Default
Firmware Version
Sub-menu
DMX Address Setting
channel 1Ch
channel 3Ch
channel 4Ch
channel
channel 5Ch
channel 10Ch
channel 15Ch
Mode L
Mode Q
Dimmer Curve
Mode I
Mode S
Cipher Setup
0-999
Lock
Key Mode
UnLock
Celsius Degree
Temp Uint CS
Fahrenht Degree
Value Clear
DMX Status
Value Hold
Auto
Display Mode
On
Temp
Hour
Red
0-255
Green
0-255
Blue
0-255
White
0-255
Set Red
0-255
Set Green
0-255
Seg Blue
0-255
Color 0-51
4
Main functions
1. address:Current DMX address
A.Setting DMX address by button
press ENTER button when show the address menu, then adjust
the DMX address by pressing [UP] or [DOWN] button
Press [ENTER] to confirm or pressing [ESC] to return to main
menu.
B.Setting DMX address by controller
1.Set the DMX value of channel 5 to 10-15,channel 17 to 20-26,
channel 7 to 30-36,channel 8 to 40-46,then the devices
connected to the controller will enter to the setting address mode
2. Set the DMX value of channel 1 from 0-59,then you will see
the the first number of the Address change to (channel 1
vaule)/10.
For example,when set the value of channel 1 to 20,the first DMX
address number will be 2(20/10=2) ,
3. Set the DMX value of channel 2 from 0-99,then you will see
the the sencond number of the Address change to (channel 2
vaule)/10.
For example,when set the value of channel 2 to 30,the first DMX
address number will be 2(30/10=3) ,
4.Set the DMX value of channel 3 from 0-99,then you will see the
the third number of the Address change to (channel 3 vaule)/10.
For example,when set the value of channel 1 to 40,the first DMX
address number will be 3(40/10=4) ,
And the DMX address you set by conctroller will be 234.
5. Set the DMX value of channel 4 to 255,then you will save the
DMX address setted by the controller.
Caution: It won’t save the address if the address number is
over 512
6. set the value of channel 5-8 out of the value range show on the
step 1,and the device will exit the setting address mode
2. config
Setting DMX mode
press ENTER button when show the channel menu, then select
the DMX mode by pressing [UP] or [DOWN] button
5
Setting Dimmer Curve
press ENTER button when show the dimmer curve menu, then
select the dimmer curve by pressing [UP] or [DOWN] button
Setting Cipher
press ENTER button when show the cipher setup menu, then
setup cipher by pressing [UP] or [DOWN] button
Key mode
press ENTER button when show the key mode menu, then
select lock or unlock by pressing [UP] or [DOWN] button
Show Temperature
press ENTER button when show the Temp Uint CS menu, select
the way of showing the fixture’s temperature in ℃ or ℉ by
pressing [UP] or [DOWN] button
DMX status
press ENTER button when show the DMX Status menu, then
select clear value or hold value by pressing [UP] or [DOWN]
button
Display mode
press ENTER button when show the Display Mode menu, then
select auto or on by pressing [UP] or [DOWN] button
3. System info
Temperature
press ENTER button when show the Temperature menu, then it
will show the temperature of the fixture
Fixture time
press ENTER button when show the Fixture time menu, then it
will show how long time of the fixture already used
4. Color menu
press ENTER button when show the Color menu, press Enter
button to select the color mode, then adjust the color by pressing
[UP] or [DOWN] button
5. White balance
press ENTER button when show the white balance menu, press
6
Enter button to select the color mode, then adjust the color by
pressing [UP] or [DOWN] button
6. Auto test
press ENTER button when show the auto test menu, select test
mode by pressing [UP] or [DOWN] button
DMX functions and values
1CH Mode
1
0-255
Static color
2CH Mode
0-007
8-015
16-151
1
152-175
176-199
200-244
245-255
2
0-255
Shutter Blackout
Shutter open
Variable Strobe
Pulse Close
Pulse Open
Variable Random Strobe
Shutter Open
Master Dimmer
3CH Mode
1
2
3
0-255
0-255
0-255
Red Dimmer
Green Dimmer
Blue Dimmer
4CH Mode
1
2
3
4
0-255
0-255
0-255
0-255
Red Dimmer
Green Dimmer
Blue Dimmer
White Dimmer
7
6CH Mode
1
2
3
4
5
6
0-007
8-015
16-151
152-175
176-199
200-244
245-255
0-255
0-255
0-255
0-255
0-255
Shutter Blackout
Shutter open
Variable Strobe
Pulse Close
Pulse Open
Variable Random Strobe
Shutter Open
Master dimmer
Red Dimmer
Green Dimmer
Blue Dimmer
White Dimmer
8CHF Mode
1
0-255
2
0-255
3
0-255
4
0-255
5
0-255
6
0-255
7
0-255
8
0-255
Red Dimmer
Red Dimmer Fine
Green Dimmer
Green Dimmer Fine
Blue Dimmer
Blue Dimmer Fine
White Dimmer
White Dimmer Fine
9CHF Mode
1
0-255
2
0-255
3
0-255
4
0-255
Master dimmer
Red Dimmer
Red Dimmer Fine
Green Dimmer
8
5
6
7
8
9
0-255
0-255
0-255
0-255
0-255
10CHF Mode
1
0-255
2
0-255
3
0-255
4
0-255
5
0-255
6
0-255
7
0-255
8
0-255
9
0-255
10
0-255
Green Dimmer Fine
Blue Dimmer
Blue Dimmer Fine
White Dimmer
White Dimmer Fine
Master dimmer
Master dimmer fine
Red dimmer
Red dimmer fine
Green dimmer
Green dimmer fine
Blue dimmer
Blue dimmer fine
White dimmer
White dimmer fine
10CHD Mode
1
2
3
4
5
0-007
8-015
16-151
152-175
176-199
200-244
245-255
0-255
0-255
0-255
0-255
Shutter Blackout
Shutter open
Variable Strobe
Pulse Close
Pulse Open
Variable Random Strobe
Shutter Open
Master dimmer
Red1 dimmer
Green1 Dimmer
Blue1 Dimmer
9
6
7
8
9
10
0-255
0-255
0-255
0-255
0-255
14CHD Mode
1
0-255
2
0-255
3
0-255
4
0-255
5
0-255
6
0-255
7
0-255
8
0-255
9
0-255
0-15
10
16-255
11
0-255
12
13
14
0-35
36-71
72-107
108-143
144-179
180-215
216-255
0-255
0-63
64-127
White1 Dimmer
Red2 Dimmer
Green2 Dimmer
Blue2 Dimmer
White2 Dimmer
Master dimmer
Red1 dimmer
Green1 Dimmer
Blue1 Dimmer
White1 Dimmer
Red2 Dimmer
Green2 Dimmer
Blue2 Dimmer
White2 Dimmer
No Effect
Strobe Rate(0 - 30HZ)
Color Macro Color+Black
Auto run
No Effect
ramp up
ramp down
ramp up/down
color mix mode
4-colors
43-colors
dimmer speed
dimmer curve
L curve
S curve
10
128-191
192-255
15CHF Mode
1
0-255
2
0-255
3
0-255
4
0-255
5
0-255
6
0-255
7
0-255
8
0-255
9
0-255
10
0-255
0-15
11
16-255
12
0-255
13
14
15
0-35
36-71
72-107
108-143
144-179
180-215
216-255
0-255
0-63
64-127
128-191
192-255
I curve
Q curve
Master dimmer
Master dimmer fine
Red dimmer
Red dimmer fine
Green dimmer
Green dimmer fine
Blue dimmer
Blue dimmer fine
White dimmer
White dimmer fine
No Effect
Strobe Rate(0 - 30HZ)
Color Macro Color+Black
Auto run
No Effect
ramp up
ramp down
ramp up/down
color mix mode
4-colors
43-colors
dimmer speed
dimmer curve
L curve
S curve
I curve
Q curve
11
CLEANING AND MAINTENANCE
We recommend a frequent cleaning of the device. Please use a soft
lint-free and moistened cloth. Never use alcohol or solvents!
CAUTION!Disconnect from mains before starting
maintenance operation.
There are no servicable parts inside the device. Maintenance and
service operations are only to be carried out by authorized dealers.
If you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to
be replaced by authorized dealers only in order to avoid hazards.
If you have further questions, please contact your dealer.
INSTALLATION
The device must only be installed at a vibration-free, oscilation-free
and fire-resistant location.
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising