PANORAM V12 Mini
12 function cycle computer
(Wire/Wireless version)
INSTALLATION FOR WIRE VERSION
DETAILED PARTS DESCRIPTION
GB
DISPLAY
FUNCTION
ACCESSORIES FOR
ACCESSORIES FOR
WIRELESS
WIRE VERSION
ACCESSORIES (Fits all size handlebar.)
1
2a-3
VERSION
2b-2
2a-5
Option A
Option A
S
Bike1/Bike2 wheel
circumference setting
Trip Distance
ACCESSORIES FOR WIRE VERSION
Total time
1. Computer Body
2. Computer Bracket set A
2-1 Spacer
2-2 Washer
2-3a M4 x 12mm Bolt
2-3b M4 x 23mm Bolt
2a-1 Computer Bracket
2a-2 Sensor
2a-3 Sensor Cable
Standard: 83cm
Extra long: 170cm
2a-4 Sensor Rubber Pad
Low battery indicator
12H/24H clock
Speed pace indicator
wireless version
Art. no TPC-11 (standard)
TPC11-XL (extra long) for trainer
Art. no. TPC-12
Button lock
Contact
Unit selection
DETERMINE WHEEL CIRCUMFERENCE FIRST
Tire Size Designation
32-630
28-630
40-622
40-622
40-635
37-622
18-622
20-622
23-622
25-622
28-622
32-622
35-622
40-622
1217
1590
1948
1907
1973
2026
2051
2070
2089
2114
2133
2105
2086
27x1 1/4
27x1 1/4 Fifty
28x1.5
28x1.75
28x1 1/2
28x1 1/8x1 5/8
700x18c
700x20c
700x23c
700x25c
700x28c
700x32c
700x35c
700x40c
2199
2174
2224
2268
2265
2205
2102
2114
2133
2146
2149
2174
2205
2224
23mm
+
LR44
-
CHANGING BATTERIES
WIRELESS
VERSION
KM/H:
Wheel Circumference
=mm x 3.14
Wheel Circumference
SENSOR
3. Wheel Magnet Set
3-1 Wheel Magnet
3-2 Magnet Ring
3-3 Magnet Screw
4. Handlebar Bracket
4-1 Bracket (26.0~22.2)
4-2 Bracket (31.8~28.6)
4-3 Handlebar Bracket Bolt
4-4 Rubber Pad (Thin)
4-5 Rubber Pad (Thick)
BIKE 1:
+
LR44
-
90˚
A˚< 15˚
CR2032
BIKE 2:
mm X 3.14
NOTE:
The sensor battery is supplied,
but not installed. Install the
sensor battery before using
the computer.
TROUBLE SHOOTING
FUNCTION
SHOWN ON SCREEN
Bike1/Bike2 wheel
circumference setting
READ ON SCREEN
SPECIFICATIONS
INCREMENTS ACCURACY
BIKE1: 2265mm, BIKE2: 2050mm 0~3999
over 99.9 "o.o"
Current speed
99.9 KM/H, 99.9 M/H
0.1 KM/H or M/H
Average speed
99.9 KM/H, 99.9 M/H
0.1 KM/H or M/H
Maximun speed
21.9 KM/H
99.9 KM/H, 99.9 M/H
0.1 KM/H or M/H
Trip Distance
0.79 KM
Odometer
0 KM
Ride time
Total time
0H1M58S
3H5M
Low battery indicator
low battery
12H/24H clock
11H15M47S AM (12H)
Trip Time
0H31M42S
SPD > AVG
Sensor:
Sensor Cable:
Wheel Circumference Setting:
Operating Temperature:
Storage Temperature:
Computer Body Battery Power:
0.1 mm
21.9 KM/H will apprear
21.3 KM/H
Speed pace indicator
WIRE VERSION
Bike1: 0.0~999.99 KM or M
Bike2: 0.0~999.99 KM or M
Bike1: 0~9999 KM or M
Bike2: 0~9999 KM or M
over 99:59:59
Bike1: 00:00:00~99(H):59(M):59(S)
"Err" will apprear Bike2: 00:00:00~99(H):59(M):59(S)
Bike1: 0:00~9999(H):59(M)
Bike2: 0:00~9999(H):59(M)
over 999.9 "Err"
will apprear
0.1 KM or M
0.1 KM or M
1 Second
1 Minute
_+1 %
_+0.1 %
_+0.1 %
_+0.1 %
_+0.1 %
_+0.1 %
_+0.1 %
Dimensions/Weight:
WIRELESS VERSION
Sensor with Transmitter:
Wireless Sensing Distance:
Cross-Talking Interference:
No Contact Magnet sensor with Wireless Transmitter.
75cm (29.5") between the sensor(transmitter) and the computer body.
Within 40 cm (15.8"), no interference by 2 bicycles carrying similar cycle
computers,even when ridden side by side.
Wheel Circumference Setting: 0mm - 3999mm (1mm increment)
Operating Temperature:
0˚C ~ 60˚C (32˚F ~ 140˚F)
Storage Temperature:
- 20˚C ~ 80˚C (-4˚F ~ 176˚F)
Main Unit Battery Power:
3V battery x 1 (CR2032), Battery life, approximately 1.3 years.
(Based on an average of 1.5 hours use per day)
Transmitter Battery Power: 1.5V battery x 1 (typical LR44). 15,000 miles riding distance, or approximately
two years. (Battery included with sensor may have shorter battery life due
to initial shipping and storage time.)
Dimensions/ Weight:
Computer Body: 40 x 32 x 16 mm / 17g
Sensor(Transmitter): 20.0 mmø x 48.0 mm / 13g
3V
1:00:00~12:59:59 (12H)
0:00:00~23:59:59 (24H)
0:00:00~99(H):59(M):59(S)
_+0.01 %
_+0.01 %
1 Second
1 Second
SPD < AVG
Button lock
lock
Wheel circumference default: BIKE1-2155mm, BIKE2-2050mm
1. The TOPEAK PANORAM cycle computer can be used
CHECK ITEMS
REMEDY
No display
1. Is the battery exhausted?
2. Is the battery installed correctly?
1. Replace the battery.
2. Make sure that the positive (+) pole of the battery is facing the battery cap.
1. Is it in setup mode?
2. Are the contacts between the computer body and the bracket poor?
3. Are the relative positions and gap between sensor and magnet correct?
4. Is the wheel circumference correct?
1. Refer to the data setting procedure and complete the adjustment.
2. Clean the contacts.
3. Refer to INSTALLATION and re-adjust correctly.
4. Refer to CIRCUMFERENCE SETTING and enter correct value.
No current
speed or
incorrect
data
LCD is black
Display is slow
Did you leave the main unit in direct sunlight when
not riding the bicycle for a long while?
Place the computer body in the shade to return to normal state.
Is the temperature below 0˚C (32˚F)?
The unit will return to normal state when the temperature rises.
M
+
S
3sec
SET Button/
Button Lock S
M
SCREEN 1
A2. UNIT SELECTION
Press
S
A3. BIKE1
CIRCUMFERENCE
SETTING
M
2sec
M
NOTE:
When no data inputs for
20 seconds, the screen
will switch to SCREEN 1
automatically.
S
M
M
digit 0~3
digit 0~9
2sec
M
2sec
M
M
M
digit 0~23 (24H) /
1~12 (12H)
2sec
• • •
M
ODO
2sec
M
SCREEN 2
SCREEN 3
M
4sec
2sec
BIKE1
SCREEN 4
CLEAR DATA
M
(AS, DST, MS, RT, TRIP TIME)
BIKE2
SCREEN 3
M
digit 0~9
digit 0~9
digit 0~9
SCREEN 5
4sec
1sec
CLEAR DATA
(AS, DST, RT, TRIP TIME)
CLEAR
SCREEN 4
M
• • •
M
WIRELESS
M
4sec
S
M
M
M
M
digit 0~9
digit 0~9
digit 0~5
digit 0~9
SCREEN 1
During non-riding status,
if no button is touched for
30 minutes, the screen will
go into Sleep Mode.
Screen will wake up by
touching MODE button.
LIMITED WARRANTY
1. CLEAR ALL DATA SETTING will clear all stored data.
2-year Warranty: All electronic and mechanical components
against manufacturer defects only. Batteries are not covered
under any implied warranty.
3. KM/H or M/H selection is only available from CLEAR
ALL DATA SETTING.
SENSOR
4. Before changing battery, write down stored data
ODO and ART. All of data of Bike1 & Bike 2 will
be cleared when replacing battery, however, this
computer will allow you to re-enter your stored
data.
M
2sec
NOTE:
2. CLEAR ALL DATA SETTING is required during FIRST
SETUP or BATTERY CHANGE.
When DST over "999.9" or
RT over "99:59:59, "Err"
will appear. Use CLEAR
DATA function to erase DST
& RT data.
M
>5 sec
CLEAR
digit 0
SLEEP MODE
2sec
M
M
Following the
setup procedure
A3 ~ A6
M
WIRE
2sec
4sec
S
BIKE2 SET UP
S
STOP
5sec
M
S
ODO
M
>5 sec
4sec
M
digit 0~5
2sec
STOP
M
• • •
digit 0~9
M
M
2sec
REBUILD KIT
M
A6. BIKE1 ART SETTING
>5 sec
M
M
M
2sec
2sec
START
CLEAR DATA
S
A5. BIKE1 ODO SETTING
2sec
M
M
S
M
M
M
4sec
START
M
ODO
TRIP TIME
(AS, DST, MS, RT, TRIP TIME)
• • •
M
computer body or its accessories.
M
2sec
1sec
M
A4. CLOCK SELECTION
6. Do not use thinner, alcohol, or benzine to clean the
CLEAR DATA
M
M
2sec
computer body periodically.
(AS, DST, MS, RT, TRIP TIME)
SCREEN 1
RESET DATA
SCREEN 2
5. Clean the bracket contacts and the button of the
TRIP TIME
M
S
M
magnet periodically.
C. NORMAL DATA SETTING (RIDING STATUS)
M MODE
Press and Hold
when not riding the bicycle.
3. Do not disassemble the computer body or its accessories.
7. Remember to pay attention to the road while riding.
S
Button
2. Do not leave the main unit exposed to direct sunlight
4. Check relative positions and gap between sensor and
Refer to "Clear All Data setting" and initiate the computer again.
Irregular display
LOCK MODE
A1. CLEAR ALL DATA
in the rain but should not be submerged in water.
PROBLEM
B. NORMAL DATA SETTING (NON-RIDING STATUS)
A. SETUP
PRECAUTIONS
Check the following before bringing unit in for repair.
No Contact Magnetic Sensor.
TPC-6: 83cm(Standard), TPC6-XL: 170cm (Extra Long)
0mm - 3999mm (1mm increment)
0˚C ~ 60˚C (32˚F ~ 140˚F)
- 20˚C ~ 80˚C (-4˚F ~ 176˚F)
3V battery x 1 (CR2032), Battery life, approximately two years.
(Based on an average of 1.5 hours use per day)
Computer Body: 40 x 32 x 16 mm / 17g
A˚
NOTE: During non-ride periods, never leave wheel magnet next to fork
sensor. This will shorten sensor battery life.
SPECIFICATIONS
DISPLAY
Max. 5mm (0.2")
Max. 5mm (0.2")
(2
16 x1.75 x2
20 x1.75x2
24x1 3/8A
24x1.75x2
26x1
26x1.5
26x1.6
26x1.75x2
26x1.9
26x2.00
26x2.215
26x1 3/8
26x1 3/8x1 1/2
1. Computer Body
2. Computer Bracket set B
2-1 Spacer
2-2 Washer
2-3a M4 x 12mm Bolt
2-3b M4 x 23mm Bolt
2b-1 Computer Bracket
2b-2 Sensor (Transmitter)
with Zip Belt
2b-3 Sensor Rubber Pad
METHOD B). WHEEL CIRCUMFERENCE MEASUREMENT
Tire Size Designation
23mm
5cm
L < 7 eet)
.5 f
47-305
47-406
37-540
47-507
23-571
40-559
44-559
47-559
50-559
54-559
57-559
37-590
37-584
Wheel Circumference
ACCESSORIES FOR WIRELESS VERSION
2a-5 Sensor Zip Tie
3-1 Wheel Magnet
3-2 Magnet Ring
3-3 Magnet Screw
4. Handlebar Bracket
4-1 Bracket (26.0~22.2)
4-2 Bracket (31.8~28.6)
4-3 Handlebar Bracket Bolt
4-4 Rubber Pad (Thin)
4-5 Rubber Pad (Thick)
WHEEL CIRCUMFERENCE OF MY BIKES
METHOD A). WHEEL CIRCUMFERENCE REFERENCE TABLE
Option B
4-2 4-3 4-4 4-5
Trip Time
wire version
Option B
2a-1
Release
Button
Release
Button
2b-1
3-1 3-2 3-3
Ride time
Battery
Cover
12mm
2b-3
2-3b
Odometer
SET Button/
Button Lock
S
SENSOR
12mm
S
MODE
Button
4-1
S
M
2-1 2-2
SENSOR
2a-2
S
2-3a
Average speed
Maximun speed
2a-4
S
Current speed
INSTALLATION FOR WIRELESS VERSION
S
PANORAM V12 Mini
#RK-TPC-6
STANDARD
SENSOR CABLE: 83cm
#RK-TPC6-XL
EXTRA LONG
SENSOR CABLE: 170cm
#RK-TPC-7
Warranty Claim Requirements
To obtain warranty service, you must have your original sales
receipt. Items returned without a sales receipt will assume
that the warranty begins on the date of manufacture. All
warranties will be void if PANORAM V12 Mini cycle computer
is damaged due to user crash, abuse, system alteration,
modification, or used in any way not intended as described
in this operating manual.
* The specifications and design are subject to change without notice.
Topeak products are available only from professional bicycle shops.
Please contact your nearest Topeak authorized bicycle dealer for any questions.
For customers in the USA, call: 1-800-250-3068 Website: www.topeak.com
Copyright © Topeak, Inc. 2009
M-TPC11-12-GB 5/09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising