Somfy Product Catalogue 2010-2011

Somfy Product Catalogue 2010-2011
www.homeelectric.de
Somfy Product
Catalogue 2010-2011
Guide to Motorised & Automated Solutions
Contents
Introduction
Roman, Cellular & Venetian
Blinds
New products ........................... 3
Motor Selection Charts ................. 46
Why Somfy? ............................. 6
Tilt Wirefree RTS ......................... 51
Warranty ................................. 8
Cord Lift Wirefree RTS ................... 53
General Information .................. 10
CTS25 ...................................... 55
Somfy Technologies ................... 13
LV25 ....................................... 57
Important Information ................ 15
LW25 ...................................... 59
Roller Blinds
AMS25 .................................... 61
Motor Selection Chart ................. 18
CTS40 ..................................... 63
LT28 ...................................... 19
Altus 40 RTS ............................. 65
Roll-up Wirefree ....................... 21
LS40 ....................................... 67
Altus 40 RTS ............................. 23
J5 .......................................... 69
LS 40 ..................................... 25
J4 .......................................... 71
Altus 50 .................................. 27
Accessories ............................... 72
LT 50 ..................................... 29
Curtains
Sonesse 30 .............................. 31
Glydea 35 ................................ 84
Sonesse 40 .............................. 33
Glydea 60 ................................ 85
Sonesse 50 .............................. 34
Accessories ............................... 87
Accessories .............................. 38
[1]
Awnings
Commercial Building
Solutions
Motor Selection Chart ................. 91
Animeo Solo ............................ 140
Altus 50/60 RTS ......................... 93
Animeo IB+ Compact ................. 147
Orea 50/60 RTS / WT ................... 95
Animeo IB+ Premium ................. 155
LT 50/60 ................................. 99
LT 50/60 CSI ............................. 101
Controls
Phoenix ................................ 105
Telis Remotes ........................... 171
Accessories ............................. 107
RS485 RTS Transmitter ................. 175
Cables ................................... 116
RS485 ILT Interface .................... 176
Windows, Louvres, Domes
Transmitters ............................. 177
Sensors .................................. 178
Motor Selection Chart ................ 120
Receivers ................................ 179
Linkeo .................................. 125
Switches ................................ 180
Rodeo .................................. 129
Motor Brackets ......................... 131
Wiring Diagrams ........ 186
ILT Motors
ILT 2 Motors ............................. 133
Sonesse 50 ILT 2 ........................ 135
Controls .................................. 137
Accessories .............................. 138
[2]
2010 New Products
Glydea Range
Glydea 35 WT/RTS
Glydea 60 WT/RTS
Available in
Q3 2010
Glydea is the new solution for curtains by Somfy, for
a smooth and easy automation, with extraconvenience and better performance.
Wirefree Range
Roll-Up Wirefree
CordLift Wirefree
Tilt Wirefree
The Wirefree Range allows to motorise blinds in
difficult access areas, with its 2-year lasting battery
it is an easy and problem-free solution.
Sonesse 40 pa/rts
The new silent motor by Somfy, to extend the
already existing silent range for comfort and
convenience
Available in
Q4 2010
[3]
J4/j5
This motor has been designed for automation of
wooden venetian blinds, managing both the up and
down movement as well as the angle of the slats.
rs485 rts transmitter
To control your Somfy motors from your home automation solution with one centralised system. Functions
with all RTS Somfy devices.
Sunis and Thermosunis
Indoor Wirefree Sensors
Autonomous Temperature and Sunlight sensor, providing energy savings all-year round, that can be placed
anywhere in the house.
[4]
A Worldwide Presence
Somfy offices and subsidiaries around the world
Argentina
Australia
Austria
Baltic States
Belgium
Brazil
Canada
China
Croatia
Cyprus
Czech Republic
Denmark
France
France – Export
France – Head Office
Finland
Germany
Greece
Hong Kong
Hungary
India
Indonesia
Iran
Israel
Italy
Japan
Jordan
Kingdom of Saudi
Arabia
Kuwait
Lebanon
Malaysia
Mexico
Morocco
Netherlands
New Zealand
Norway
Poland
Portugal
Romania
Russia
Serbia
Singapore
Slovak Republic
South Africa
South Korea
Spain
Sweden
Switzerland
Syria
Taiwan
Thailand
Tunisia
Turkey
United Arab Emirates
United Kingdom
United States
Vietnam
www.somfy.co.in
[5]
W
For more than 40 years, Somfy is innovating and is now the world’s leading
manufacturer of motors and control systems for Blinds, Awnings, Roller Shutters,
Projection Screens, Windows and Gates.
Designed to provide convenience, comfort and energy savings, Somfy’s automated
solutions are an important enhancement for homes and commercial buildings. At
the push of a button, or automatically, they will open or close, extend or retract,
providing shade, privacy and security.
State-of-the-art technology is incorporated in the design and manufacture of
Somfy motors and controls, ensuring exceptional performance and reliability.
Somfy products undergo stringent quality controls and conform to national and
international standards. All Somfy products carry a five-year warranty.
Established in the heart of the European Community, Somfy comes from an area in
the Alps renowned for its precision instrument technologies. Somfy’s production
facilities include product research and development, robot assisted production
lines and stringent quality control of incoming parts and finished goods. Somfy’s
factories are certified to ISO 9001 by Lloyd’s of London.
Today, Somfy home and building automation solutions are sold in 54 countries
serviced by 53 subsidiaries. With 5,400 employees, Somfy has over 30,000
customers and 220 million users of our solutions worldwide.
[6]
Why Somfy?
Customer Support
Somfy are specialists in motors and controls for openings.
Somfy has a dedicated Customer Support Team to support our customers in India with
sales and technical assistance. For assistance please call + 91 (0) 11 46 111 523
Somfy has an After Sales Service team to quickly diagnose and resolve the cause of any
failures.
Technical Support
Somfy Technical Support includes:
•
Advice on motor and controller solutions
•
Assistance with special projects
•
Advice on electrical requirements
•
Providing wiring diagrams
•
Installation support
•
Advice when trouble shooting
•
After Sales Service
Marketing Support
Somfy is dedicated to promoting the use of motorised and automated solutions.
We are eager to work with you, our partner, to develop the markets for the automation
of openings in homes and buildings.
Somfy Marketing Support includes:
•
Promotional ideas/recommendations
•
Exhibition support
•
POS literature and tools
•
Direct mail
•
Joint advertising
Product Quality and Supply
Somfy is a global market leader certified to ISO 9001 standards.
The Somfy group produces over 7 million motors annually. Of these over 2 million have
built-in radio receivers.
Somfy carries a large stock of motors and controls with the majority of orders despatched
same day.
Somfy has a diverse range of motors including radio motors, hard-wired motors,
low voltage motors, curtain motors, gate motors and window openers.
Somfy has a diverse range of electronics and controls for all applications.
All products carry a 5-year warranty.
[7]
Warranty
All Somfy products carry a 5-Year Limited Warranty.*
*As per warranty condition of Somfy India Pvt. Limited.
Obligations
Exclusions
SOMFY’s only obligation shall
be to repair or replace, with the
least possible delay, defective
equipment which does not
conform to the warranty without any other indemnity
relating to installation and re-installation or
consequential damages.
The following are exclusions from warranty:
1. I f u s a g e , a d a p t a t i o n o r i n s t a l l a t i o n a r e n o t
in accordance with our written installation and
operating instructions.
2. If the product has been opened, dismantled or
returned with clear evidence of abuse or other
damage.
SOMFY shall not be liable for any injury, loss or
damage, direct or consequential, arising out of the
use of, or the inability to use, the equipment. Before
using, the Buyer and/or the end User shall determine
the suitability of the product for its intended use,
and User assumes all risks and liability in connection
therewith.
3. If our written specifications are not properly applied
by the Buyer when selecting the equipment.
4. I f o ur wr i t te n i n s tru c ti o n s fo r i n s ta l l a ti o n a n d
wiring of the electrical connections have not been
followed.
5. I f o u r e q u i p m e n t h a s b e e n u s e d t o p e r f o r m
functions other than the functions it was originally
designed to handle, namely motorising window
and door coverings and enclosures e.g. awnings,
internal & external blinds, curtains, roller shutters
& grilles, projection screens, gates and windows.
Please consult SOMFY about warranty for any uses
other than the above.
The articles that are replaced pursuant to the terms of
this warranty shall be retained by SOMFY.
All costs related to installation and re-installation of
the SOMFY equipment covered by this warranty are
not the responsibility of SOMFY.
The user is responsible for any freight costs relating to
repair or replacement. SOMFY will not be responsible
for any consequential damages during or following
installation procedures.
6. I f S O M F Y e q u i p m e n t i s u s e d w i t h e l e c t r i c a l
accessories (switches, relays etc.) that have not
been previously approved in writing by Somfy’s
Customer Support Department.
If the buyer resells any SOMFY products to another
buyer or end-user, it shall include all of the terms and
provisions of this warranty in such resale. SOMFY’s
responsibility to any such third party shall be no
greater than SOMFY’s responsibility under the warranty
to the original Buyer.
7. If the electrical accessories and other components
have been used in disregard of the basic wiring
diagram for which they were designed.
[8]
International Certification
Somfy motors have been tested by electrical authorities
around the world.
Australia &
New Zealand
Canada
Italy
Switzerland
Austria
France
Netherlands
United States
of America
Baumeister
gepruft
Belgium
Germany
Scandinavia
TUV
STUTTGART
We are proud that our motors carry the marks of the most recognised electrical testing
institutions. This indicates conformance to stringent operational and safety standards.
The Quality Management System of Somfy S.A. of Cluses, France has been certified by
Lloyds Register Quality Assurance Limited to the
Standard.
ISO 9001
[9]
General Information
All Somfy motors and controls have an IP (Protection index) rating. This rating is a guide to the degree of
protection required by the electrical equipment casing.
The IP rating is comprised of two numbers. Each number corresponds to a degree of protection in one of
the two following categories: - solid object
- water
eg:
IP 4 4
Protection against solid bodies.
IP
Protection against liquid bodies.
tests
IP
tests
0
No protection
0
No protection
1
Protected against solid particles greater than 50
mm (eg: unintentional contacts from the hand).
1
Protected against vertical water drops
(eg: condensation)
2
Protected against solid particles greater than 12.5
mm (eg: hand finger).
2
Protected against water drops falling up to 15°
from vertical.
3
Protected against solid particles greater than 2.5
mm (eg: tools, screw).
3
Protected against rain up to 60° from vertical.
4
Protected against solid particles greater than 1mm
(eg: tools, screw).
4
Protected against water splashes from all
directions.
5
Protected against dust (no deposit).
5
Protected against water squirts from all directions.
6
Totally protected against dust.
6
Protected against water projection similar to
ocean waves.
7
Protected against immersion effects.
8
Protected against lengthy, under pressure
submersions.
ATTENTION
• Somfy motors are not toys. Do not allow
children
to play with the control device(s).
• Somfy Motors are not waterproof. Electricity and
water do not mix.
• All motors mounted externally require covering.
• All motors must be mounted horizontally.
• Somfy motors are designed for intermittent use
only. A thermal overload switch protects the
motor from damage caused by overheating.
• Somfy motors are sensitive to impacts. Shocks
will damage sensitive parts.
• Drilling into the Somfy motor may cause
irreparable damage.
• When installing the Somfy motor in an outdoor
application always ensure a ‘drip loop’ is used.
• Parallel wiring and dual switching of standard
Somfy motors is strictly forbidden. See “Wiring
Diagrams” section for details.
• Failure to observe the above will void the
warranty of the motor and may pose a
significant electrical and/ or mechanical hazard.
[ 10 ]
General Information
Ensure you have read and are familiar with the electrical safety information included in this catalogue. All
work, electrical or otherwise must be carried out by trained and competent staff that are familiar with all safety
requirements and operational features of a Somfy motor.
MOTOR HEAD
LIMIT SWITCH
MOTOR
BRAKE
GEARBOX
OUTPUT SHAFT
The motor head
supports the
motorised roller
at one end of the
installation whilst
providing an
entry point for the
supply cable. Six
different mounting
positions allow for
easy access of the
limit switch push
buttons.
Push button or
electronic end
of travel limit
switches can be
easily adjusted
to set the exact
distance of travel
in both the UP and
DOWN directions.
The Somfy tubular
range comprises
asynchronous
single phase
motors with built
in capacitors.
They are thermally
protected, totally
enclosed,
brushless motors.
An electromagnetic
brake
automatically
stops and holds
the load in any
position.
Planetary type
gears lower
the rotor speed
and increase
the torque.
The gearbox is
lubricated for life.
The output shaft
is the point at
which the torque,
delivered by
the motor, is
transferred to the
roller tube via the
drive wheel to
which it will be
connected.
FUNCTIONING PRINCIPLE
The motor is supported by the bracket and the roller tube.
The motor drives the wheel.
The wheel drives the motor tube.
The roller tube drives the crown.
The crown turns the limit switch unit within the motor.
NOTE:
Not all Somfy motors are alike the one shown above. Motor heads,
limit switches, output shafts, size, weight, function and overall
design can vary depending on the installation type.
[ 11 ]
General Information
Basic concepts & Catalogue notes
Torque
Torque = load x radius
Torque unit: Nm or mkg (10Nm = 1mkg)
Load unit: N or kg
Radius (diameter ÷ 2) unit: m
radius
Example:
load
What will be the theoretical weight lifted by a Vega motor
(60 Nm or 6 mkg) mounted inside a Ø70 roller tube?
Load = torque ÷ radius
i.e 60 Nm ÷ 0.035 m = 1714 (171.4 kg)
What is the motor required to lift a 90 kg load with a Ø50 roller tube?
Torque = load x radius
i.e 900 N x (0.050 m ÷ 2) = 22.5 Nm (2.25 mkg)
As the roller tube is 50mm in diameter, the motor to choose is in the
LT50 or Altus 50 range.
The Gemini or Altus 25 has a torque of 25Nm, so either motor would
be suitable to use.
Speed
The speed shown is the rotation speed (in rpm) of the
motor, and thus the roller tube.
To calculate the average translation speed of the system (in
cm/ sec) being motorised, use the following formula.
Sm (cm/sec)
Sm = ((D + d) x 3.14 x n) ÷ (2 x 60)
d = Diameter of roller tube (cm)
D = Diameter of the system when rolled up (cm)
n = rotation speed (rpm) of motor
To calculate the opening time (in seconds) of a roller shutter,
use the following formula.
t = h ÷ SM
h = height of the system (cm)
Sm = average translation speed (cm/sec)
[ 12 ]
Somfy Technologies
As a world leader in the development of motors for openings Somfy is committed to delivering
control solutions for any installation. Listed below are the major technologies that Somfy employs
in order to cover the range of varying integration and connectivity techniques around the world.
Radio Technology Somfy is an exclusive remote control protocol used to operate
selected Somfy motors and controllers. RTS uses a rolling code with 16million
combinations to ensure that the RTS communication is safe and secure. In addition
RTS has a range of up to 200 metres (line of sight) or up to 20 metres through two
concrete walls. Fast becoming a standard, due to its ease of installation and its
flexibility RTS is the most reliable and successful radio system on the market.
ILT
ILTv2
Intelligent Limit Technology is employed by Somfy ILT series motors. These motors
are controlled by the ILT data cable with power drawn through the traditional
230v – 240v power lead. A feature of these motors is highly accurate limits. Control
connection is a very simple with groups and sub-groups easily managed by
incorporating matchbox size control boards on the ILT motor data cable. The addition
of remote or infrared control is equally simple.
Intelligent Limit Technology Version 2 uses the same connection method as the ILT
motors and controllers, but incorporates more sophisticated electronics. With ILT v2
motors and controllers, integration to a BMS/HAS allows for a greater flexibility in
control. ILT v2, for example, can be programmed through an AV system to lower a
projection screen to suit a 4:3 format for regular television viewing, then when movie
viewing is required, at the touch or a button can readjust the height of the screen to
suit a 16:9 or 16:10 format.
Infrared is another remote control method of operating selected Somfy motors and
controllers. Infrared control is most often used in the Audio-Visual industry with
infrared being an easily ‘learnt’ control method for universal remotes.
Wired Technology is the most basic method of control for a Somfy motor. It uses a
direct connection from a control point eg. a wall switch, to a motor, via a 230v - 240v
wire. This wired technique employs two active wires, one when powered, engages
the motor’s drive shaft in a clockwise rotation, the other when powered engages an
anti-clockwise rotation.
DIGITAL TECHNOLOGY SOMFY
RS485 is another control method that uses a two-wired bus. Due to the open source
nature of the RS485 protocol many building management systems (BMS) and home
automation systems (HAS) use this protocol to communicate to devices. Systems
that can use the RS485 connection can be programmed to Somfy RS485 motors or
controllers to operate the installation. Due to it’s open source nature, the integrator
just needs to plug the device directly into their BMS or HAS without the need for
additional controllers or the adaptation of peripherals.
[ 13 ]
Somfy Technologies
International Bus uses a three-wire configuration to communicate to Somfy motors
and controllers. Basic operations can be carried out ie. Up, Stop, Down and ‘My’
position. Many Somfy controllers use this connection method as it can be easily
integrated into Home Automation or Building Management Sytems.
International Bus Plus uses a four wire configuration to communicate to Somfy motors
and controllers. Digital information is carried across the fourth wired used in this
method in order for compatible controllers to carry out advanced functions. Basic
operation is still carried out along the other three wires. Somfy’s Animeo IB+ system
uses this connection method for complete façade management.
Local Outed Network is a two-wire communication method developed by the
Echelon Corp primarily as a commercial building control solution. This proprietary
communication is used to integrate many types of devices, from Somfy Motor
Controllers to HVAC and lighting controllers. Somfy’s LON 4AC Motor Controller employs
this protocol in order to directly integrate Somfy motors to this system. A specialised
integrator is required to be employed for programming the device.
KNX/European Installation Bus is a proprietary two-wire communication method
used to integrate many types of devices, from Somfy Motor Controllers to HVAC and
lighting controllers. Somfy’s EIB/KNX 4AC Motor Controller employs this protocol in
order to directly integrate Somfy motors to this system. A specialised integrator is
required to be employed for programming the device. The KNX/EIB protocol is mostly
employed in European made controllers for commercial buildings.
[ 14 ]
Important Information
Please read before using this catalogue
•
All measurements contained herein are shown in millimetres unless otherwise noted.
•
Each selection chart is intended as a guide only; variations exist between types of installations. Always check
with your manufacturer if you are unsure of any details.
•
Selection charts do not reflect altering factors such as links, mechanically induced drag, environmental
factors, etc.
•
Some motors have specific installation requirements; check with the hardware manufacturer or Somfy before
fitting / specifying an installation for the first time.
•
Whilst every effort has been taken to ensure the technical accuracy of the information contained herein, Somfy
does not assume responsibility for any errors that may exist. Variations within electrical tolerances, electrical
load, mechanical tolerances, etc. are a factor that must be kept in mind when specifying and / or relaying
information.
•
Somfy electronics, mechanical accessories, adaptors, cables, etc. have been designed and tested for use with
Somfy motors and associated Somfy equipment. We assume no responsibility nor guarantee the use of third
party devices with Somfy parts.
•
Functionality is not guaranteed on installations that are not covered under the norms of general use (custom
installations), unless specific written consent is issued via Somfy.
•
Every Somfy electrical item is issued with an installation guide(s). It is the responsibility of the recipient of the
goods shipped by Somfy, to forward this document(s) to all relevant parties. End user guides are available
for selected Somfy items. It is also the responsibility of the retailer to supply the end user with appropriate
information as to the requirements for the safe operation of their Somfy motorised system.
•
All work, electrical or otherwise, must be carried out by competent staff that have been trained, licensed and
are familiar with the equipment and goods required for the safe installation and operation of Somfy goods.
•
Always check the Somfy website for the latest updates on new products, changes to existing products and
discontinuations.
[ 15 ]
[ 16 ]
Roller Blinds
MOTORS & ACCESSORIES
Motor Selection Chart .......................................... 18
LT28 ............................................................... 19
Rollup Wirefree ................................................. 21
Altus 40 RTS ...................................................... 23
LS 40 ............................................................. 25
Altus 50 RTS ...................................................... 27
LT50 ............................................................... 29
Sonesse 30 RTS / Sonesse 30 Dry Contact .................... 31
Sonesse 40 RTS / Sonesse 40 PA .............................. 33
Sonesse 50 RTS / Sonesse 50 PA ............................ 34
Adaptors:
Rollup, Sonesse 30, 40, 50mm Motors ..................... 38
Motor Brackets:
LT28, Rollup, Sonesse 30, 40, 50mm Motors ............... 41
Bearings:
LT28, Rollup, Sonesse 30, 40, 50mm Motors ............... 43
Plug end Brackets:
Rollup, Sonesse 30, 40, 50mm Motors .................... 44
INTERNAL ROLLER BLINDS
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
Calculating the weight of the blind:
weight = width x drop x weight per m2
Also take into consideration the weight of the bottom bar.
How to select the tube and motor for roller blinds?
Step-1: To calculate the total weight of the blinds
Total weight (in Kg)= area (sq.m.) x weight of the blind (sq.m)
(Fabric + Bottom Bar)
Step-2: Tube selection
Based upon the width and weight of the blinds, tube can be selected.
[ 18 ]
LT 28
MAIN CHARACTERISTICS & FEATURES
24V DC tubular motor.
The LT28 is a SELV (Safety Extra Low Voltage) 24V DC tubular motor. With a torque of
0.7Nm, it is adapted for Ø28mm tubes. Fitted with rapid set limits and the advantage
of not requiring an electrician to install due to the utilisation of 24V DC SELV, the LT28
is a versatile tubular motor for small installations.
Rapid set limits.
40 turn limit capacity.
Suitable for tubes: Ø28.
24V switch control via electronic or mechanical means.
Supplied with a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
26mm
LT28 (PIN)
Torque (Nm)
0.7
[ 19 ]
Speed (RPM)
27
Ref.
1000039
LT 28
TECHNICAL CHARACTERISTICS
Grey = Positive or Negative
24V DC SELV
(Safety Extra-Low
Voltage) motor.
White = Negative or Positive
17
L1
LT28 (PIN)
29
L1 (mm)
285
Torque (Nm)
0.7
Speed (rpm)
27
Turn Capacity
40
Rated Voltage (V)
24
Rated Current (A)
0.375
Average running noise (dbA)
Minimum tube diameter
NOTE
The polarity used will determine the direction
of rotation for the motor.
Eg. Grey = Positive (+)
White = Negative (-)
will make the motor rotate in a clockwise direction
when mounted on the right.
50
28 x 0.7
Motor weight (kg)
0.27
Index Protection
IP44
Information about the noise is according to Somfy
measures and is for information only. Taken as the
worst value in load, for the up direction during
the first 10 seconds of travel.
Normal functioning temperature: -20°C to +60°C
[ 20 ]
ROLLUP WIREFREE RTS
MAIN CHARACTERISTICS & FEATURES
12V DC Battery tubular motor.
When a retrofit is required or power cannot be accessed the Roll Up
Wirefree is the answer. Utilising power saving software and a reloadable
battery wand, with RTS functionality and with its adaptable design, it
is suitable for Ø40mm to Ø45mm* tubes. The Roll Up Wirefree does not
require an electrician to install the unit due to the SELV (Safety Extra-Low
Voltage) 12v it uses. The Roll Up Wirefree requires no extra effort than a
manual blind to install.
Remote set limits.
Turning capacity limited only by thermal time.
Suitable for tubes: Ø40 to Ø45*.
Memory Capacity: 12 transmitters.
Programmable “my” position.
Requires the use of specific crowns and wheels for tube adaptation.
Horizontal mount only.
Intermittent Usage.
30mm
ROLLUP WIREFREE RTS
Torque (Nm)
1.13
Speed (RPM)
27
Ref.
1000637
* Any tube size other than the Ø40mm Louvolite is not catered for by Somfy.
NOTE: When utilising a louvolite system, the roll up wirefree RTS requires the bracketing and idler accessories
from a manual louvolite system, not supplied by Somfy.
[ 21 ]
ROLLUP WIREFREE RTS
TECHNICAL CHARACTERISTICS
12v DC SELV
(Safety Extra-Low
Voltage) motor.
The Rollup WF utilises
Lithium batteries, wiring
only is present to link the
battery to the motor.
WARNING
The Rollup Wirefree is
polarity sensitive.
Ensure correct connection
before powering. Damage
may result from incorrect
connection.
ROLLUP WIREFREE RTS
Do not force the one way
connector into the socket.
L1 (mm)
264
Torque (Nm)
1.13
Speed (rpm)
27
Rated Voltage (VDC)
12
NOTE
Rated Current (A)
1.0
Running time before thermal cut off (min)
2.5
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Average running noise (dbA)
65
Minimum tube diameter
40
Motor weight (kg)
0.22
Index Protection
IP30
Normal functioning temperature: 0°C to +60°C
[ 22 ]
ALTUS 40 RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Altus 40 RTS is ideal for roller blinds with limited room. With its slim 38mm
design, it can be adapted to Ø40mm tubes or larger. A quiet drive and built-in radio
receiver are a few of the design features of the Altus 40 RTS.
Remote set limits.
4 minute running time.
Suitable for tubes: Ø40
Memory Capacity: 12 transmitters, plus 3 sensors.
Programmable “my” position.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
40mm
ALTUS RTS 3/30
ALTUS RTS 4/14
ALTUS RTS 9/14
Torque (Nm)
3
Speed (RPM)
30
Ref.
1020056
Torque (Nm)
4
Speed (RPM)
14
Ref.
1021144
Torque (Nm)
9
Speed (RPM)
14
Ref.
1023117
[ 23 ]
ALTUS 40 RTS
TECHNICAL CHARACTERISTICS
Blue = Neutral
CLASS II
The Altus 40 is classified
as a Class II Double
Insulated Device. As such
an earth connection is
NOT required.
Brown = Active
L1
40mm
13.5
ø 38
L2
ALTUS RTS 9/14
L1 (mm)
497
457
497
L2 riveting distance (mm)
473
433
473
Torque (Nm)
3
4
9
Speed (rpm)
30
14
14
ALTUS RTS 3/30
ALTUS RTS 4/14
ø 12
29
Rated Voltage (V)
230
230
230
Rated Power consumption (W)
80
65
100
Rated Current (A)
0.4
0.35
0.5
4
4
4
140
140
140
Running time before thermal cut off (min)
Thermal cut off temp (°C)
52
52
54
40 X 1.5
40 X 1.5
40 X 1.5
Motor weight (kg)
1.08
1.01
1.18
Cable length (M)
3
3
3
Number of cores in cable
2
2
2
Cross section of cable (mm²)
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
Average running noise (dbA)
Minimum tube diameter
60
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Normal functioning temperature: -10°C to +40°C
[ 24 ]
LS40
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Ls40 is a hardwired motor suitable for roller blinds with limited room. With its
slim 38mm design, it can be adapted to Ø40mm tubes and above. A quiet drive,
reliable progressive limiting and low power consumption are a few of the design
features of the Ls40.
Progressive (screw type) set limits.
40 turn limit capacity.
Suitable for tubes: Ø40, Acmeda 45, etc.
230V switch control via electronic or mechanical means*.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
40mm
MERCURE 3/30
ARIES S 4/14
MARS 9/14
Torque (Nm)
3
Speed (RPM)
30
Ref.
1020009
Torque (Nm)
4
Speed (RPM)
14
Ref.
1021021
Torque (Nm)
9
Speed (RPM)
14
Ref.
1023010
* Parallel wiring of motors is prohibited without the use of an isolation controller, eg. 4AC Motor Controller,
4 Motor Group Controller, etc. Direct switching of a 230V motor must always be done via a mechanical interlock.
[ 25 ]
LS40
TECHNICAL CHARACTERISTICS
Blue = Neutral
CLASS II
The LS40 is classified as a
Class II Double Insulated
Device. As such an
earth connection is NOT
required.
Brown = Active 1
Black = Active 2
L1
40mm
13.5
ø 38
L2
MERCURE 3/30
ARIES S 4/14
MARS 9/14
ø 12
29
L1 (mm)
442
398
442
L2 riveting distance (mm)
421
377
421
Torque (Nm)
3
4
9
Speed (rpm)
30
14
14
Turn Capacity
40
40
40
Rated Voltage (V)
230
230
230
Rated Power consumption (W)
80
65
100
Rated Current (A)
0.4
0.35
0.5
4
4
4
140
140
140
Running time before thermal cut off (min)
Thermal cut off temp (°C)
52
52
54
40 x 1.5
40 x 1.5
40 x 1.5
Motor weight (kg)
0.95
0.94
1.06
Cable length (M)
2.5
2.5
2.5
3
3
3
Cross section of cable (mm²)
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
Average running noise (dbA)
Minimum tube diameter
Number of cores in cable
60
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Normal functioning temperature: -10°C to +40°C
[ 26 ]
ALTUS 50 RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Altus 50 RTS is suitable for a wide range of roller blind application types.
Available in torques from 6Nm & 15Nm, coupled with its flexible 48mm
design, it is adapted for Ø50mm tubes and above. Available in the traditional
star head style to allow for extra fabric drifting, a built-in radio receiver with
Somfy’s rolling code and the installation flexibility of remote control make the
Altus 50 RTS a suitable all round performer.
Remote set limits.
Turning capacity limited only by thermal time.
Suitable for tubes: Ø50 to Ø65.
Memory Capacity: 12 transmitters, plus 3 sensors.
Programmable “my” position.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
ALTUS RTS 6/17
ALTUS RTS 6/32
ALTUS RTS 15/17
Torque (Nm)
6
Speed (RPM)
17
Ref.
1032448
Torque (Nm)
6
Speed (RPM)
32
Ref.
1032558
Torque (Nm)
15
Speed (RPM)
17
Ref.
1039378
[ 27 ]
ALTUS 50 RTS
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active
Yellow /Green = Earth
L1
L2
3.95
Ø 47
50mm
25
17.15
min
20
ALTUS RTS 15/17
ALTUS RTS 6/32
ALTUS RTS 6/17
Ø 63
L1 (mm)*
605
655
655
L2 riveting distance (mm)*
590
640
640
15
Torque (Nm)
6
6
Speed (rpm)
17
32
17
Rated Voltage (V)
230
230
230
Rated Power consumption (W)
Rated Current (A)
Running time before thermal cut off (min)
Thermal cut off temp (°C)
90
120
140
0.45
0.5
0.65
4
4
4
140
140
150
NOTE
47
52
50
50 x 1.5
50 x 1.5
50 x 1.5
Motor weight (kg)
1.72
2.21
2.12
Cable length (M)
3
5
3
Number of cores in cable
3
3
3
Cross section of cable (mm²)
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
Average running noise (dbA)
Minimum tube diameter
Normal functioning temperature: -10°C to +40°C
Information about
the noise is according
to Somfy measures
and is for information
only. Taken as the
worst value in load,
for the up direction
during the first 10
seconds of travel.
*For wheels on tubes ø50 x 1.5 add 8mm to L1 (mm) and L2.
[ 28 ]
LT 50
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The LT50 is suitable for a wide range of roller blind application types. Available in
torques from 6Nm to 15Nm, coupled with its flexible 48mm design, it is adapted for
Ø50mm tubes and above. Available in the traditional star head style to allow for
fabric drift. Rapid set push button limits and the adaptability of 230V control
make the LT50 a suitable all round performer.
Rapid set limits.
46 turn limit capacity.
Suitable for tubes: Ø50 to Ø65.
230V switch control via electronic or mechanical means*.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
ARIANE 6/17
ARIANE 6/32
JET 10/17
ATLAS 15/17
ATLAS 15/32
Torque (Nm)
6
Speed (RPM)
17
Ref.
1032050
Torque (Nm)
6
Speed (RPM)
32
Ref.
1032066
Torque (Nm)
10
Speed (RPM)
17
Ref.
1037062
Torque (Nm)
15
Speed (RPM)
17
Ref.
1039051
Torque (Nm)
15
Speed (RPM)
32
Ref.
1039065
* Parallel wiring of motors is prohibited without the use of an isolation controller, eg. 4AC Motor Controller,
4 Motor Group Controller, etc. Direct switching of a 230V motor must always be done via a mechanical interlock.
[ 29 ]
LT 50
TECHNICAL CHARACTERISTICS
Blue = Neutral
NOTE
Brown = Active 1
Information about the noise is according to
Somfy measures and is for information only.
Taken as the worst value in load, for the up
direction during the first 10 seconds of travel.
Black = Active 2
Green/Yellow = Earth
L1
L2
3.95
Ø 47
50mm
17.15
min
25
20
24
ATLAS 15/32
L1 (mm)*
505
525
525
525
605
L2 riveting distance (mm)*
490
510
510
510
590
Torque (Nm)
6
6
10
15
15
Speed (rpm)
17
32
17
17
32
JET 10/17
ATLAS 15/17
ARIANE 6/17
ARIANE 6/32
Ø 63
Turn Capacity
46
46
46
46
46
Rated Voltage (V)
230
230
230
230
230
Rated Power consumption (W)
90
120
120
140
240
Rated Current (A)
0.4
0.5
0.5
0.65
1.1
4
4
4
4
4
140
140
140
140
150
Running time before thermal cut off (min)
Thermal cut off temp (°C)
Average running noise (dbA)
46
52
47
50
56
50 x 1.5
50 x 1.5
50 x 1.5
50 x 1.5
50 x 1.5
Motor weight (kg)
1.72
1.85
1.85
1.95
2.55
Cable length (M)
2.5
2.5
2.5
2.5
2.5
4
4
4
4
4
Cross section of cable (mm²)
0.75
0.75
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
IP44
IP44
Minimum tube diameter
Number of cores in cable
Normal functioning temperature: -10°C to +40°C
*For wheels on tubes ø50 x 1.5 add 8mm to L1 (mm) and L2.
[ 30 ]
Ø 74
SONESSE 30 RTS
SONESSE 30 DRY CONTACT
MAIN CHARACTERISTICS & FEATURES
24V DC tubular motor.
The Sonesse 30 has been adapted to be a quiet* DC roller blind motor.
Available in 2Nm and with its slim 29mm design, it is adapted for Ø40mm to Ø45mm
tubes. Utilising either RTS control or dry contact switching, the Sonesse 30 consumes
little power due to the SELV (Safety Extra-Low Voltage) 24v it runs on.The Sonesse 30
is a quick and quiet performer for installations that require a minimal level of noise.
silent
range
Remote set limits or setting tool for Sonesse Dry Contact.
35 turn limit capacity.
Suitable for tubes: Ø40 to Ø45.
Memory Capacity: 12 transmitters.
Programmable “my” position.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
30mm
SONESSE 30 RTS
SONESSE 30 DRY CONTACT
Torque (Nm)
2
Speed (RPM)
28
Ref.
1000460
Torque (Nm)
2
Speed (RPM)
28†
Ref.
1000668
* Quiet operation is dependant on installation factors, please contact Somfy or consult the installation guide
for the appropriate measures to take in order to achieve a minimum level of noise.
† Variable Speed
[ 31 ]
SONESSE 30 RTS
SONESSE 30 DRY CONTACT
TECHNICAL CHARACTERISTICS
Grey = Positive or
White = Negative
NOTE:
Maximum mounting
screw length into motor
head is 7.04mm.
SONESSE 30 DRY CONTACT
L1 (mm)
SONESSE 30 RTS
Damage may result from
exceeding this length.
407
407
WARNING
The Sonesse 30
is polarity sensitive.
Ensure correct connection
before powering. Damage
may result from incorrect
connection.
Do not force the one way
connector into the socket.
Torque (Nm)
2
2
Speed (rpm)
28
28*
Turn Capacity (per each directional rotation)
35
60
Rated Voltage (V)
24
24
Rated Current (A)
0.8
0.8
Running time before thermal cut off (min)
2.5
2.5
Average running noise (dbA)
44
44
40 x 1.5
40 x 1.5
Motor weight (kg)
0.49
0.49
Cable length (M)
2.2
2.2
Minimum tube diameter
Number of cores in cable
2
2
Cross section of cable (mm²)
0.2
0.2
Index Protection
IP30
IP30
Normal functioning temperature: 0°C to +60°C
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
*Variable speed
[ 32 ]
SONESSE 40 RTS
SONESSE 40 PA
230V/50Hz tubular motor.
Sonesse 40 RTS motor is integrated with a radio receiver in quiet range.
Available in 3 different torque, it is adapted for 40mm to 50mm diameter tubes.
Transmission range: up to 200m in free space and 20m with two reinforced concrete
walls in between.
Requires the use of a crown and wheel for tube adaptation
silent
range
Horizontal mount only.
Intermittent usage.
Sonesse
Sonesse
Sonesse
Sonesse
Sonesse
Sonesse
40
40
40
40
40
40
RTS
PA
RTS
PA
RTS
PA
3/30
3/30
6/20
6/20
9/12
9/12
Torque (Nm)
Torque (Nm)
Torque (Nm)
Torque (Nm)
Torque (Nm)
Torque (Nm)
3
3
6
6
9
9
Nominal Speed(RPM)
Nominal Speed(RPM)
Nominal Speed(RPM)
Nominal Speed(RPM)
Nominal Speed(RPM)
Nominal Speed(RPM)
30
30
20
20
12
12
Ref. 1001573
Ref. 1001540
Ref. 1001577
Ref. 1001550
Ref. 1001581
Ref. 1001551
Sonesse 40 6/20
Sonesse 40 9/12
Nominal torque (Nm)
Nominal speed (rpm)
Nominal voltage
Power consumption (W)
Rated current (A)
Radio frequency (MHz)
Running time (min)
Protection index IP
Wire Section (Sq.mm)
Number of wires in cable
Net weight of the motor (kg)
L1 (mm)
L 2 (mm)
L 3 (mm)
Sonesse 40 3/30
TECHNICAL DETAILS
3
30
230 V - 50Hz
110
0.5
433.42
4
31
0,75
2
1.225
504
480
517
6
20
230 V - 50Hz
130
0.6
433.42
4
31
0,75
2
1.225
504
480
517
9
12
230 V - 50Hz
130
0.6
433.42
4
31
0,75
2
1.225
504
480
517
[ 33 ]
Note:
Sonesse 40 will be
available in
Q4 2010
Information is subject to
change
Sonesse 50 RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
silent
range
The Sonesse 50 RTS has been adapted to be a quiet* roller blind motor. Available
in 3Nm, coupled with its flexible 48mm design, it is adapted for Ø50mm tubes
and above. Available in the traditional starhead style to allow for extra fabric drifting,
a built-in radio receiver with Somfy’s rolling code and the installation flexibility of
remote control make the Sonesse 50 RTS a quick and quiet performer for installations
that require a minimal level of noise.
Remote set limits.
Turning capacity limited only by thermal time.
Suitable for tubes: Ø50 to Ø65.
Memory Capacity: 12 channels / transmitters, plus 3 sensors.
Programmable “my” position.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
SONESSE 50 RTS 3/28
Torque (Nm)
3
Speed (RPM)
28
Ref.
* Quiet operation is dependant on installation factors, please contact Somfy or consult the installation
guide for the appropriate measures to take in order to achieve a minimum level of noise.
[ 34 ]
1030032
Sonesse 50 RTS
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active
Yellow /Green = Earth
L1
L2
3.95
Ø 47
50mm
17.15
min
25
20
SONESSE 50 RTS 3/28
Ø 63
L1 (mm)
783
L2 riveting distance (mm)
770
Torque (Nm)
3
Speed (rpm)
28
Rated Voltage (V)
230
Rated Power consumption (W)
90
Rated Current (A)
0.4
Running time before thermal cut off (min)
4
Thermal cut off temp (°C)
120
Average running noise (dbA)
<44
Minimum tube diameter
63 x 1.5*
Motor weight (kg)
2.87
Cable length (M)
3
Number of cores in cable
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
3
Cross section of cable (mm²)
0.75
Index Protection
IP31
Normal functioning temperature: 0°C to +60°C
*For the best results, it is advised that the minimum tube used is 63mm in diameter.
[ 35 ]
SONESSE 50
SONESSE 50 PA
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Sonesse 50 has been adapted to be a quiet† roller blind motor.
Available in 3Nm, coupled with its flexible 48mm design, it is adapted for
Ø50mm tubes and above. Rapid set push button or progressive limits (PA) and
the adaptability of 230V control make the Sonesse 50 a quick, quiet performer
for installations that require a minimal level of noise.
Rapid set or progressive limits.
46 turn limit capacity (29 for Sonesse 50 PA).
Suitable for tubes: Ø50 to Ø65.
230V switch control via electronic or mechanical means*.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
SONESSE 50 3/28
SONESSE 50 PA 3/28
Torque (Nm)
3
Speed (RPM)
28
Ref.
1030038
Torque (Nm)
3
Speed (RPM)
28
Ref.
1030039
* Parallel wiring of motors is prohibited without the use of an isolation controller, eg. 4AC Motor Controller,
4 Motor Group Controller, etc. Direct switching of a 240V motor must always be done via a mechanical interlock.
† Quiet operation is dependant on installation factors, please contact Somfy or consult the installation guide
for the appropriate measures to take in order to achieve a minimum level of noise.
Specific Idler end plug and stop wheel must be used for correct quiet operation.
[ 36 ]
SONESSE 50
SONESSE 50 PA
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active 1
Black = Active 2
Green/Yellow = Earth
L1
L2
3.95
Ø 47
50mm
17.15
min
25
20
24
Ø 74
SONESSE 50 PA 3/28
SONESSE 50 3/28
Ø 63
L1 (mm)
712
712
L2 riveting distance (mm)
701
701
Torque (Nm)
3
3
Speed (rpm)
28
28
Turn Capacity
46
29
Rated Voltage (V)
230
230
Rated Power consumption (W)
90
90
Rated Current (A)
0.4
0.4
Running time before thermal cut off (min)
4
4
Thermal cut off temp (°C)
120
120
Average running noise (dbA)
<44
<44
Minimum tube diameter
NOTE
63 x 1.5*
63 x 1.5*
Motor weight (kg)
2.52
2.52
Cable length (M)
2.5
2.5
Number of cores in cable
4
4
Cross section of cable (mm²)
0.75
0.75
Index Protection
IP31
IP31
Normal functioning temperature: 0°C to +60°C
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
*For the best silent results, it is advised at minimum the tube used is 63mm in diameter.
[ 37 ]
ADAPTORS
Roll Up, Sonesse 30mm,
40mm, 50mm MOTORS
Rollup
Ref.
9014046
Suitable only for the Rollup
Wirefree.
Louvolite
ø40
Note: When utilising a Louvolite system, the Rollup Wirefree RTS requires the bracketing
and idler accessories from a manual Louvolite system, not supplied by Somfy.
Sonesse 30
Ref.
ø40
Crown and
Drive round
tube kit
9014344
Adaptation for Sonesse 30 motor
to ø40 tube, requires suitable
ø40 wheel.
Ref.
9014045
Requires the use of Louvolite
brackets from a manual system.
Louvolite
ø40 kit
Ref.
9014333
Requires the use of Louvolite
brackets from a manual system.
Louvolite
ø45 kit
LS40 CROWN AND DRIVE ADAPTOR KIT
Allows for the use of LS40 wheels and crowns
with a Sonesse 30 motor.
Only Suitable for Sonesse 30
Ref.
9013776
[ 38 ]
ADAPTORS
Roll Up, Sonesse 30mm,
40mm, 50mm MOTORS
40mm
Tube
Profile
Wheel
Crown
1,5
Wheel
Ref.
9147544
Crown
Ref.
9147330
Wheel
Ref.
9132138
Crown
Ref.
9132139
Wheel
Ref.
9206088
ø40
40
2
4,5
Madopron
ø40
50
50mm
1,5
1,6
No Crown
Adaptor
Required
Ø50
Round
50
[ 39 ]
ADAPTORS
Roll Up, Sonesse 30,
40mm, 50mm MOTORS
50mm
Tube
Profile
Wheel
Crown
1,5
ø63 x 1.5
Round
Wheel
Ref.
9206019
Crown
Ref.
9707026
Wheel
Ref.
9751002
Crown
Ref.
9707030
Wheel
Ref.
9751002
Crown
Ref.
9707030
63
Issey
ø63
63
Sunmaster
ø65
[ 40 ]
MOTOR BRACKETS
LT28, Sonesse 30,
40mm, 50mm MOTORS
LT28
AN GL E B RACK E T K I T
Angle bracket for LT28 with pin.
Supplied with screws.
Ref.
9030000
Sonesse 30, 40mm
LS40 MOTOR BRACKET
LS 40 KIT
White angle motor head bracket.
Motor bracket, End plug bracket, End plug
Supplied with two screws.
Maximum Torque: 13 Nm
Ref.
9500683
Ref.
9137009
50mm
R I G H T A N G L E B R ACK E T
BRACKET WIT H 10mm S T UD
Right angle motor bracket for 50mm motors.
For standard star head 50mm motors.
Supplied with ring.
Use with bracket ref. 9410665 or 9137029.
Also available in White: 9410652.
Black: 9012878.
Maximum Torque: 25 Nm
Maximum Torque: 50 Nm
Ref.
9410651
Ref.
[ 41 ]
9910013
MOTOR BRACKETS
LT28, Sonesse 30,
40mm, 50mm MOTORS
50mm
B R ACK E T COV E R
UNIVERSAL ZAMACK BRACKET
Fix Points:
- 2 holes Ø6mm, 48mm apart.
Used to conceal bracketing.
White in colour, indoor use only.
- 2 holes Ø8mm, 60mm apart.
Use with 9410665, 9410651, 9410639.
- 2 holes Ø8mm, 60mm apart with bolt head.
Maximum Torque: 85 Nm
Ref.
9910000
Ref.
INTERMEDIATE BRACKETS
Sonesse 50mm MOTORS
50mm
INTERMEDIATE BRACKET
Allows the running of two fabrics on separate
tubes via a single motor.
Requires 2 x wheels for tube utilised.
Suitable only for a ø50 tube.
Also available in White: 9002564
Black: 9012880
Maximum Torque: 15 Nm
Ref.
9410654
[ 42 ]
9002519
BEARINGS
LT28, Sonesse 30,
40mm, 50mm MOTORS
LT28
PLUG END Ø28
Ø4 pin.
For tube adaptation.
Ref.
9013933
Sonesse 30, 40, 50mm
PLUG END WITHOUT SHAF T
PLUG END
For use with a plug end shaft.
Ø8 pin.
On Ø40 tubes.
Use with Ø40 wheel.
For tube adaptation.
Use with ref. 1781009.
34,5
47
Ref.
9129630
Maximum Torque: 13 Nm
Ref.
PLUG END SHAF T Ø12
9500688
SPRING LOADED PLUG END Ø12
Ø12 pin.
Length adjustment of: 30mm.
Use with plug end ref. 9129630.
Crown and Wheel adaptor required.
For tube adaptation.
(see adaptors section).
Maximum Torque: 50 Nm
Ref.
1781009
Ref.
9420801
CROWN & WHEEL MOUNTING FOR SPRING LOADED PLUG ENDS
When utilising the bearings, a crown and
wheel must be fixed to the item to ensure
correct operation.
[ 43 ]
PLUG END BRACKETS
Sonesse 30,
40mm, 50mm MOTORS
Sonesse 30, 40mm
LS40 PLUG END BRACKET
IDLER BRACKE T Ø12
White angle bracket.
Right angle mount.
For Ø8 plug end.
For Ø12 pin.
Use with ref. 9500688.
Also available in White: 9410634
Black: 9012879.
Maximum Torque: 4.5 Nm
Maximum Torque: 50 Nm
Ref.
9500685
Ref.
9410633
50mm
BRACKET COVER
IDLER BRACKE T Ø12
Used to conceal bracketing.
Right angle mount.
White in colour, indoor use only.
For Ø12 pin.
Use with 9410633, 9410635.
Also available in White: 9410634
Black: 9012879.
Maximum Torque: 50 Nm
Ref.
9002519
Ref.
[ 44 ]
9685181
9410633
Roman, Cellular &
Venetian Blinds
MOTORS & ACCESSORIES
Motor Selection Charts:
Venetian Blinds ................................................ 46
Pleated Blinds .................................................. 47
Cellular Blinds .................................................. 48
Timber Venetian Blinds ....................................... 49
Roman Blinds .................................................. 50
Tilt Wirefree ...................................................... 51
Cord Lift Wirefree ................................................ 53
CTS25 .............................................................. 55
LV25............................................................... 57
LW25.............................................................. 59
AMS25 ............................................................. 61
CTS40 ............................................................. 63
Altus 40 RTS ..................................................... 65
LS40 ............................................................... 67
J 5 ................................................................. 69
J 4 .................................................................. 71
Accessories - CTS25, CD25, LV25, LW25, AMS25 .............. 72
Shaft Adaptors - CTS25, CD25, LV25, LW25, AMS25.......... 73
Cones & Cone Covers - CTS25 ................................. 74
Rings & Ladder Grips - CTS25 ................................. 75
Roman Accessories - CTS 40 ................................. 76
Headrail & Shaft Adaptors - Tilt Wirefree................... 77
Headrail & Shaft Adaptors - Cord Lift Wirefree ........... 78
Accessories - Tilt & Cord Lift Wirefree ....................... 79
J 5 Accessories .................................................. 80
VENETIAN BLINDS
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the drop of the application (“y” axis).
• Select the width of the application (“x” axis).
• Follow both sizes until they intersect, the required motor will
fall on the intersection.
• If the sizes fall outside the chart then the application type is not
possible under those conditions.
25mm ALUMINIUM VENETIAN BLINDS WITH CTS25
• Slat weight: 550g/m²
• Bottom bar weight: 260g/m
• Cord diameter: 1.4mm
NOTE: These are the factors used within the
selection chart.
Width in metres
Maximum width with LV motors
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
0.6
0.8
1.0
1.2
1.4
0.4Nm
Drop in metres
1.6
0.6Nm
1.8
0.8Nm
2.0
2.2
Not Possible
2.4
2.6
2.8
3.0
3.2
Torque -->
0.4 Nm
0.6 Nm
LV Motor
Designation
3.4
LV25-B44
LV25-B64
LW Motor
Designation
Torque -->
0.4 Nm
0.8 Nm
LW25-B44
LW25-B83
LW25-E83
[ 46 ]
3.2
3.4
3.6
PLEATED BLINDS
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the drop of the application (“y” axis).
• Select the width of the application (“x” axis).
• Follow both sizes until they intersect, the required motor will
fall on the intersection.
• If the sizes fall outside the chart then the application type is not
possible under those conditions.
PLEATED BLINDS WITH CTS25
• Fabric weight: 130g/m²
• Bottom bar weight: 260g/m
• Cord diameter: 1.4mm
NOTE: These are the factors used within the
selection chart.
Width in metres
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
0.6
0.8
1.0
1.2
1.4
Drop in metres
1.6
1.8
0.4Nm
2.0
2.2
2.4
0.8Nm
2.6
2.8
3.0
3.2
3.4
3.6
LW Motor
Designation
Torque -->
0.4 Nm
0.8 Nm
LW25-B83
[ 47 ]
3.4
3.6
CELLULAR BLINDS
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the drop of the application (“y” axis).
• Select the width of the application (“x” axis).
• Follow both sizes until they intersect, the required motor will
fall on the intersection.
• If the sizes fall outside the chart then the application type is not
possible under those conditions.
CELLULAR BLINDS WITH CTS25
• Fabric weight: 310g/m²
• Bottom bar weight: 350g/m
• Cord diameter: 1.4mm
NOTE: These are the factors used within the
selection chart.
Width in metres
Maximum width with LV motors
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
0.6
0.8
1.0
1.2
1.4
0.4Nm
Drop in metres
1.6
1.8
0.6Nm
2.0
2.2
0.8Nm
2.4
2.6
2.8
Not Possible
3.0
3.2
3.4
0.4 Nm
LV Motor
Designation
Torque -->
LW Motor
Designation
Torque -->
0.6 Nm
LV25-B64
0.4 Nm
0.8 Nm
LW25-B83
[ 48 ]
3.6
[ 49 ]
TILT WIREFREE RTS
MAIN CHARACTERISTICS & FEATURES
12V DC Battery tilt only motor
When a retrofit is required or power cannot be accessed for a timber venetian
the Tilt Wirefree is the answer. Utilising power saving software and a reloadable
battery wand, RTS Modulis functionality and with an adaptable design, it is
suitable for 51 x 57mm or 38 x 57mm headrails and a variety of shafts. The Tilt
Wirefree does not require an electrician to install due to the SELV (Safety Extra-Low
Voltage) 12v it uses and requires no extra effort than a manual blind to install.
Remote set limits with Modulis compatibility.*
Suitable for headrails: 51 x 57mm and 38 x 57mm.
Suitable for shafts: 4mm square, 5mm hexagonal, D-rod
Memory Capacity: 12 channels / transmitters.
Programmable “my” position.
Requires the use of specific headrail and drive shaft adaptors.
Horizontal mount only.
Intermittent Usage.
TILT WIREFREE RTS
Torque (Nm)
1
* Modulis remote required.
For:
Timber Venetians
[ 51 ]
Speed (RPM)
12
Ref.
1000678
TILT WIREFREE RTS
TECHNICAL CHARACTERISTICS
12v DC SELV
(Safety Extra-Low
Voltage) motor.
The Tilt Wirefree utilises
lithium batteries,
wiring only is present
to connect the battery
to the motor.
WARNING
91.4
TILT WIREFREE RTS
The Tilt Wirefree is polarity
sensitive.
Damage may result from
incorrect connection.
Do not force the one way
connector into the socket.
Torque (Nm)
1
Speed (rpm)
12
NOTE
Rated Voltage (V)
12
Rated Current (A)
0.4
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Running time before thermal cut off (min)
5
Average running noise (dbA)
44
Motor weight (kg)
0.45
Index Protection
IP30
Normal functioning temperature: 0°C to +60°C
[ 52 ]
CORD LIFT WIREFREE RTS
MAIN CHARACTERISTICS & FEATURES
12V DC Battery cord / tape motor.
If the flexibility of battery operation is needed for a pleated, cellular,
Roman blind or balloon window covering that uses a tape take up,
the Cordlift Wirefree is the answer. Utilising power saving software and a
reloadable battery wand, RTS functionality and with an adaptable design,
it is suitable for a range of headrail sizes and shafts. The Cordlift Wirefree does
not require an electrician to install the unit due to the SELV (Safety Extra-Low
Voltage) 12V it uses.
Remote set limits.
Suitable for headrails: Kensington, HD East Glide, Easy Rise and Graber.
Memory Capacity: 12 transmitters.
Programmable “my” position.
Requires the use of specific headrail and drive shaft adaptors.
Horizontal mount only.
Intermittent Usage.
CORD LIFT WIREFREE RTS
Torque (Nm)
0.34
For:
Balloon / Roman Blinds
Pleated & Cellular Blinds
[ 53 ]
Speed (RPM)
58
Ref.
1000494
CORD LIFT WIREFREE RTS
TECHNICAL CHARACTERISTICS
12v DC SELV
(Safety Extra-Low
Voltage) motor.
The Tilt Wirefree utilises
lithium batteries,
wiring only is present
to connect the battery
to the motor.
WARNING
The Cord Lift Wirefree is
polarity sensitive.
Damage may result from
incorrect connection.
Do not force the one way
connector into the socket.
CORD LIFT WIREFREE RTS
113.95
Torque (Nm)
0.34
Speed (rpm)
58
NOTE
Rated Voltage (V)
12
Rated Current (A)
0.83
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Running time before thermal cut off (min)
3
Average running noise (dbA)
53
Motor weight (kg)
0.183
Index Protection
IP30
Normal functioning temperature: 0°C to +60°C
[ 54 ]
CTS25
CONCEPT 25
MAIN CHARACTERISTICS & FEATURES
The CTS25 (Cord Take Up System) has been patented by Somfy for the even
winding and tilting of blinds using a cord drive. It’s unique design allows
tilting in only a small movement and lowering / raising in a full movement,
in either direction using no additional components. By it’s traversing shaft a
maximum of 3.4m (Long Cone) can be wound up using this system.
Suitable for headrails: Holis, HD Basic, HD Ultimate, Faber, etc.
Requires the use of a specific cone and headrail adaptors as well.
No preferential direction of rotation.
Horizontal mount only.
CTS 25 CONE PARTS
CONE
Pg. 74
BEARING
Pg. 72
RING
Pg. 75
CONE COVER
Pg. 74
Horizontal
Applications
with CTS25
LV25 Size: ≤ 7m²
LW25 Size: ≤ 9m²
Height: ≤ 3.4m
Roman Blinds
with CTS25
(depending on fabric)
LW25 Weight: ≤ 4kg
Height: ≤ 3.4m
Venetian Blinds
with CTS25
LV25 Size: ≤ 4m²
LW25 Size: ≤ 5m²
Height: ≤ 3.4m
Pleated Blinds
with CTS25
LW25 Size: ≤ 12m²
Height: ≤ 3.4m
Cellular Blinds
with CTS25
LV25 Size: ≤ 7.5m²
LW25 Size: ≤ 11m²
Height: ≤ 3.4m
[ 55 ]
CTS25
CONCEPT 25
TECHNICAL CHARACTERISTICS
NOTE
The CTS25 is comprised of
many parts in order to
function correctly with the
headrail and drive shaft
within the installation.
Ensure the correct cone,
bearing, ring and cone
cover is choosen for the
application.
Long Cone: 108.3mm
13mm
Long Cone
NOTE
The above is shown only as
an example.
CTS25
CTS25 is a cord lift and tilt system for blinds driven by a
traversing shaft. It provides even cord winding on a cone.
Cord diameter (mm)
1.4
Cord type
Round Braided
Cord material
100% Polyester
Cord Braiding
16 Ends
Cord with core
Yes
Cord treatment
Stabilised
Maximum load per ø1.4mm cord (kg)
2
Maximum length of ø1.4 cord which can be rolled/turns
3.40m / 54
turns
Working temperature (˚C)
-10˚ to +85˚
*Measurements given for standard bearing types listed further on.
[ 56 ]
LV25
Concept 25
MAIN CHARACTERISTICS & FEATURES
24V DC shaft drive motor
The LV25 is a slim, single output drive shaft motor for aluminium, pleated and
cellular blinds. Adaptable for a wide range of common headrail sizes and drive
shafts, when used in conjunction with a CTS25 can lift and tilt your blind. An
integrated torque limiter and shaft play equaliser with the advantage of not
requiring an electrician to install due to the utilisation of SELV (Safety Extra-Low
Voltage) 24v.
Over torque limiting.*
No limit turn restrictions.
Suitable for headrails: Holis, Warema, HD Basic, HD Ultimate, Faber, etc.
24V switch control via electronic or mechanical means.
Requires the use of a specific bearing and drive shaft adaptors as well.
Not suitable for sealed glass applications.
Horizontal mount only.
Intermittent Usage.
LV25 - B64
Torque (Nm)
0.6
*Requires the use of an AMS25 for lower limit stopping.
For:
Aluminium Venetian Blinds
Pleated & Cellular Blinds
[ 57 ]
Speed (RPM)
35
Ref.
1000029
LV25
Concept 25
TECHNICAL CHARACTERISTICS
Grey = Positive or Negative
24v DC SELV
(Safety Extra-Low
Voltage) motor.
White = Negative or Positive
mm
mm
mm
LV25 - B64
NOTE
The polarity used will determine the direction
of rotation for the motor.
Eg. Grey = Positive (+)
White = Negative (-)
will make the motor rotate in a clockwise direction
when mounted on the right.
Torque (Nm)
0.6
Speed (rpm)
35
Rated Voltage (V)
24
Rated Current (A)
0.4
Running time before thermal cut off (min)
7
Motor weight (kg)
0.145
Index Protection
IP40
Information about the noise is according to Somfy
measures and is for information only. Taken as the
worst value in load, for the up direction during
the first 10 seconds of travel.
Normal functioning temperature: -10°C to +60°C
[ 58 ]
LW25
Concept 25
MAIN CHARACTERISTICS & FEATURES
24V DC shaft drive motor.
The LW25 is a slim, dual output drive shaft motor for aluminium, pleated and
cellular blinds. Adaptable for a wide range of common headrail sizes and drive
shafts, when used in conjunction with a CTS25 can lift and tilt your blind. With
an integrated torque limiter for the B64 and B83 motors or new for the range
the E83 motor equipped with an integrated encoder for precise movement, the
LW range is more than adequate for most installations.
Over torque limiting for LW25-B64, LW25-B83.*
Encoder limiting for LW25-E83.†
No limit turn restrictions.
Suitable for headrails: Holis, Warema, HD Basic, HD Ultimate, Faber, etc.
24V switch control via electronic or mechanical means.
Requires the use of a specific bearing and drive shaft adaptors as well.
Not suitable for sealed glass applications.
Horizontal mount only.
Intermittent Usage.
LW25 - B83
Torque (Nm)
0.8
*Requires the use of an AMS25 for lower limit stopping.
†Specific Encoder motor controller require for use.
For:
Aluminium Venetian Blinds
Pleated & Cellular Blinds
[ 59 ]
Speed (RPM)
30
Ref.
1000031
LW25
Concept 25
TECHNICAL CHARACTERISTICS
Grey = Positive or Negative
Grey = Positive or Negative
White = Negative or Positive
LW
LW-E
White = Negative or Positive
Purple = Encoder*
•Requires the use of a specific encoder motor controller.
24v DC SELV
(Safety Extra-Low
Voltage) motor.
205.5mm ± 1.3max
ø24 mm
195.5 mm ± 1.3
LW25 - B83
NOTE
The polarity used will determine the direction
of rotation for the motor.
Eg. Grey = Positive (+)
White = Negative (-)
will make the motor rotate in a clockwise direction
when mounted on the right.
Torque (Nm)
0.8
Speed (rpm)
30
Rated Voltage (V)
24
Rated Current (A)
0.47
Maximum Running time (min)
7
Motor weight (kg)
0.195
Index Protection
IP40
Information about the noise is according to Somfy
measures and is for information only. Taken as the
worst value in load, for the up direction during
the first 10 seconds of travel.
Normal functioning temperature: -10°C to +60°C
[ 60 ]
AMS25
CONCEPT 25
MAIN CHARACTERISTICS & FEATURES
The AMS25 (Adjustable Mechanical Stop) is a mechanical brake for use with the
Concept 25 range of motors. When used in an installation it will stall the motor
at its preset location, which can be adjusted at anytime. The AMS25 is built on
a reliable design and installation ease with the same mounting components as
the Concept 25 motors.
Suitable for headrails: Holis, Warema, HD Basic, HD Ultimate, Faber, etc.
Requires the use of a specific drive shaft adaptors as well.
To be used with a single Concept 25 motor only.
Horizontal mount only.
Ref.
AMS25
For:
Aluminium Venetian Blinds
Pleated & Cellular Blinds
[ 61 ]
9163030
AMS25
CONCEPT 25
TECHNICAL CHARACTERISTICS
NOTE
The AMS25 is an adjustable
mechanical brake for use
with the LV or LW concepts
motors. It is NOT an
electrically operated drive.
mm
mm
mm
mm
AMS25
mm
mm
Max Torque (Nm)
Max number of turns per direction
0.8
60
Adjustment Ratio
1/12.5
Weight (kg)
0.070
Index Protection
IP40
Normal functioning temperature: -10°C to +60°C
[ 62 ]
CTS40
MAIN CHARACTERISTICS & FEATURES
The CTS40 (Cord Take Up System) has been patented by Somfy for the even
winding and tilting of a particular installation using a cord drive. Its unique
design allows tilting in only a small movement and lowering / raising in a full
movement in either direction using no additional components. By its traversing
shaft a maximum of 5.5m of cord can be wound up using this system.
Suitable for 51 x 57 headrails.
No preferential direction of rotation.
Horizontal mount only.
CTS 40 CONE PARTS
CONE
Ref.
9162144
BEARING
Ref.
9162145
Timber
Venetian
Venetian
Blinds Blinds
with CTS40
ø40 Weight: ≤ 20kg
Max. Height: ≤ 5.5m
Roman Blinds
with CTS40
ø40 Weight: ≤ 20kg
Max. Height: ≤ 5.5m
[ 63 ]
CTS40
TECHNICAL CHARACTERISTICS
26.1±0.2 mm
8mm
±0.30
20 ±0.15 mm
40.5 ±0.3 mm
38 ±0.05 mm
41.8 ±0.2mm
ø45
31.1±0.3 mm
104.6 max mm
NOTE
The above is shown only as
an example.
CTS40
CTS40
Cord Take-up System. Cord lift and tilt system for blinds.
Driven by octagonal tube. Even cord winding on cone.
Cord diameter (mm)
1.4
Cord type
Round Braided
Cord material
100%
Polyester Yarn
Cord Braiding
16 Ends
Cord with core
Yes
Cord treatment
Stabilised
Maximum load per ø1.4mm cord (kg)
Maximum length of ø1.4 cord which can be rolled/turns
Working temperature (˚C)
4
5.5m / 35 turns
0˚ to +60˚
[ 64 ]
ALTUS 40 RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Altus 40 RTS (Radio Technology Somfy) is ideal for Roman blinds requiring
remote control. With its slim 38mm design, it can be adapted to Ø40mm tubes with
the cord take up system or Roman spools. A quiet drive and built-in radio receiver
are a few of the design features of the Altus 40 RTS.
Remote set limits.
4 minute running time.
Suitable for tubes: Ø40 and Ø40 octagonal.
Memory Capacity: 12 transmitters, 3 sensors.
Programmable “my” position.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
40mm
ALTUS RTS 3/30
ALTUS RTS 4/14
ALTUS RTS 9/14
Torque (Nm)
3
Speed (RPM)
30
Ref.
1020056
Torque (Nm)
4
Speed (RPM)
14
Ref.
1021144
Torque (Nm)
9
Speed (RPM)
14
Ref.
1023117
For:
Balloon / Roman Blind
[ 65 ]
ALTUS 40 RTS
TECHNICAL CHARACTERISTICS
Blue = Neutral
CLASS II
The Altus 40 is classified
as a Class II Double
Insulated Device. As such
an earth connection is
NOT required.
Brown = Active
L1
40mm
13,5
ø 38
L2
ALTUS RTS 3/30
ALTUS RTS 4/14
ALTUS RTS 9/14
ø 12
29
L1(mm)
497
457
497
L2 riveting distance (mm)
473
433
473
Torque (Nm)
3
4
9
Speed (rpm)
30
14
14
Rated Voltage (V)
230
230
230
Rated Power consumption (W)
80
65
100
Rated Current (A)
0.4
0.35
0.5
4
4
4
Thermal cut off temp (°C)
140
140
140
Average running noise (dbA)
52
52
54
Running time before thermal cut off (min)
40 X 1.5
40 X 1.5
40 X 1.5
Motor weight (kg)
1.08
1.01
1.18
Cable length (M)
3
3
3
Number of cores in cable
2
2
2
Cross section of cable (mm²)
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
Minimum tube diameter
60
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Normal functioning temperature: -10°C to +40°C
[ 66 ]
LS40
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The LS40 is a hardwired motor suitable for Roman blinds and timber venetians.
With its slim 38mm design, it can be adapted to Ø40mm tubes with the cord
take up system or Roman spools. A quiet drive, reliable progressive limiting and
low power consumption are a few of the design features of the LS40. Venetian
tilting functions are achieved through the use of a suitable wall switch or remote
receiver.
Progressive (screw type) set limits.
40 turn limit capacity.
Suitable for tubes: Ø40 and Ø40 octagonal.
230V switch control via electronic or mechanical means.*
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
40mm
MERCURE 3/30
ARIES S 4/14
MARS 9/14
Torque (Nm)
3
Speed (RPM)
30
Ref.
1020010
Torque (Nm)
4
Speed (RPM)
14
Ref.
1021002
Torque (Nm)
9
Speed (RPM)
14
Ref.
1023010
* Parallel wiring of motors is prohibited without the use of an isolation
controller, eg. 4AC Motor Controller, 4 Motor Group Controller, etc. Direct
switching of a 230V motor must always be done via a mechanical interlock.
For:
Balloon / Roman Blinds
Timber Venetians
[ 67 ]
LS40
TECHNICAL CHARACTERISTICS
Blue = Neutral
CLASS II
The Altus 40 is classified
as a Class II Double
Insulated Device. As such
an earth connection is
NOT required.
Brown = Active 1
Black = Active 2
L1
40mm
13,5
ø 38
L2
MERCURE 3/30
ARIES S 4/14
MARS 9/14
ø 12
29
L1(mm)
442
398
442
L2 riveting distance (mm)
421
377
421
Torque (Nm)
3
4
9
Speed (rpm)
30
14
14
Turn Capacity
40
40
40
Rated Voltage (V)
230
230
230
Rated Power consumption (W)
80
65
100
Rated Current (A)
0.4
0.35
0.5
4
4
4
140
140
140
Running time before thermal cut off (min)
Thermal cut off temp (°C)
52
52
54
40 x 1.5
40 x 1.5
40 x 1.5
Motor weight (kg)
0.95
0.94
1.06
Cable length (M)
2.5
2.5
2.5
Number of cores in cable
3
3
3
Cross section of cable (mm²)
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
Average running noise (dbA)
Minimum tube diameter
60
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Normal functioning temperature: -10°C to +40°C
[ 68 ]
J5
MAIN CHARACTERISTICS & FEATURES
The J5 motor is designed for the electric control of the external wooden Venetian blinds.
Utilizing a two-way drive system and suited for use with Somfy’s Modulis tilting electronics
to manage angle of the slats.
The upper and lower end limit is adjusted mechanically by actuating the setting button.
The upper end limit can also be off by the mushroom supplied with TN range only. Mushroom can be fitted separately in HTM range of J5 motor.
4 minute running time.
Suitable for 58 x 51 mm, 58 x 56 mm, 67 x 66 mm, 78 x 67 mm headrails.
Requires the use of a shaft adaptor.
Horizontal mount only.
Intermittent usage.
Quick and easy installation
J5 06 1 TN
J5 06 HTM
J5 10 1TN
J5 10 HTM
Torque (Nm)
Torque (Nm)
Torque (Nm)
Torque (Nm)
6
6
10
10
Speed (Rpm)
Speed (Rpm)
Speed (Rpm)
Speed (Rpm)
[ 69 ]
26
26
26
26
Ref. 1210122
Ref. 1210130
Ref. 1210123
Ref. 1210131
J5
J5 10 HTM
J5 101 TN
J5 06 HTM
J5 06 1 TN
TECHNICAL CHARACTERISTICS
Nominal torque (Nm)
6
6
6
6
Nominal speed (rpm)
26
26
26
26
230 V -
230 V -
230 V -
230 V -
50 Hz
50 Hz
50 Hz
50 Hz
Power consumption (W)
110
110
110
110
Rated current (A)
0.5
0.5
0.5
0.5
4 min
4 min
4 min
4 min
Thermal tripping tem
125
125
125
125
Protection index IP
54
54
54
54
Capacity of the LSU
60 turns
60 turns
60 turns
60 turns
0,75 Sq. mm
0,75 Sq. mm
0,75 Sq. mm
0,75 Sq. mm
3 + earth
3 + earth
3 + earth
3 + earth
Installation
Centre
Centre
Centre
Centre
Net weight of the motor
1.6 kg
1.76 kg
2 kg
2.1 kg
269
269
289
L 2 (mm)
35
35
35
35
L3 (mm)
237
255
257
275
L 4 (mm)
321
321
241
341
L 5 (mm)
16
16
16
16
Nominal voltage
Running time
Wire Section
Number of wire in cable
Dimensions L1 (mm)
289
[ 70 ]
J4
MAIN CHARACTERISTICS & FEATURES
The J4 motor is designed for the control of external wooden Venetian blinds.
Can be wired in paralled with other WT motors.
Mushroom is effective in both directions.
Setting of the motor from inside the building with the “standard setting tool”
Mushroom can be removed and plugged in the two sides of the motor.
The motor can be used in either n or u shape.
Requires the use of a shaft adaptor.
Horizontal mount only.
Intermittent usage.
For more information about J4 1TN / 2TN / HTM range, please contact customer support department
J408 WT
Ref. 1210293
J410 WT
Ref. 1210292
J406 WT
Ref. 1210291
TECHNICAL CHARACTERISTICS
Nominal torque (Nm)
6
10
Nominal speed (rpm)
26
26
26
230 V - 50Hz
230 V - 50Hz
230 V - 50Hz
Nominal voltage
Power supply tolerances (V)
18
207 - 253
207 - 253
207 - 253
Power consumption (W)
95
110
155
Rated current (A)
0.4
0.5
0.7
6 min
6 min
4 min
Running time
Protection index IP
54
54
54
Noise level (dB)
50
53
Not Confirmed
200 turns
200 turns
200 turns
0,75
0,75
0,75
3 + earth
3 + earth
3 + earth
Maximum Capacity of the LSU
Wire Section (Sq.mm)
Number of wire of cable
Installation
Centre
Centre
Centre
Dimensions L1 (mm)
254
269
289
L 2 (mm)
47
47
47
L3 (mm)
222
237
257
L 4 (mm)
306
321
341
L 5 (mm)
16
16
16
1.5 kg
1.7 kg
2.2 kg
Net weight of the motor
[ 71 ]
ACCESSORIES
FOR
CD25, LV25, LW25, AMS25, CTS25
Profile
Bearing
Headrail Adaptor
Holis/
HD Basic
Headrail type
Ref.
HD
Ultimate
9162159
Ref.
Colour: White
Colour: Black
Use with: CTS25
Use with: CD25, LV25 and LW25
use 2 pieces
AMS25 1 piece
Headrail type
Ref.
Faber
Minimatic
9163324
9162176
Ref.
9163260
Ref.
9163261
Colour: Translucent
Use with: CTS25
Headrail type
Ref.
Faber
Softline
9162139
Colour: Translucent
Use with: CTS25
Headrail type
Ref.
9162139
Ref.
9163262
Ref.
9162256
Ref.
9163331
Ref.
9163332
Ref.
9163268
Easy Rise
Headrail type
Colour: White
B.I.G
Use with: CTS25
Headrail type
Ref.
Verosol
Pleated
9162159
BEARING
PROVIDED BY VEROSOL
Headrail type
[ 72 ]
SHAFT ADAPTORS
FOR
CD25, LV25, LW25, AMS25, CTS25
Short Shaft Adaptors for AMS25
S H O RT S H A F T A D A PTO R 5 m m H E X A G O N A L
Ref.
SHORT SHAF T ADAPTOR 5mm SQUARE
9163251
Ref.
9163253
S H O RT SHAF T ADAPTO R 6m m HE X AGONA L
Used to adapt AMS25 to shaft.
Use with: AMS25 for 6mm hex shaft.
Colour: Black.
Ref.
9163252
Long Shaft Adaptors for CD25, LV25, LW25
LO N G SHAF T ADAPTOR 5m m HE XAG ONA L
Ref.
LONG SHAF T ADAPTOR 5mm SQUARE
9163254
Ref.
LO N G S H A F T A D A PTO R 6 m m H E X A G O N A L
Use with: LV25, LW25 or CD25 for 6mm
hex shaft.
Colour: Grey.
Add 4mm to LV25 and 8mm to LW25 length.
Ref.
9163255
[ 73 ]
9163256
CONES & CONE COVERS
FOR CTS25
LON G CO N E 5 m m H E X A G O N A L
Ref.
9162136
LON G CO N E 6 m m H E X A G O N A L
Used for cord takeup.
Use with: CTS25 for 6mm hex shaft.
Colour: White.
Ref.
9162137
LON G CON E 5m m SQU ARE
Used for cord takeup.
Use with: CTS25 for 5mm square shaft.
Colour: White.
Ref.
9162138
LO N G CO N E COV E R
Used for cord takeup.
Use with: CTS25 long cones.
Colour: White.
Ref.
9162140
[ 74 ]
RINGS & LADDER GRIP
FOR CTS25
RI N G 5m m H E X A G O N A L
Ref.
STOP RING
9162141
Ref.
RI N G 6m m H E X A G O N A L
STOP RING
Used to adapt cone to shaft.
Used to stop cone & accessories traversing
along the shaft.
Use with: CTS25 for 6mm hex shaft.
Colour: White.
Ref.
Use with: 6mm hex shaft and 5mm
square shaft.
9162142
Ref.
9162258
L A D D ER G RIP
RI N G 5m m SQU ARE
Ref.
9162257
9162143
Ref.
[ 75 ]
9163292
ROMAN ACCESSORIES
FOR 40mm MOTORS
Tube
Profile
Wheel
Crown
0,6
0,8
Deprat
Octagonal
ø40
Wheel
Ref.
9500344
Crown
Ref.
9132145
Wheel
Ref.
9147544
Crown
Ref.
9147330
40
1,5
ø40
40
C T S40 CONE
C T S40 B E ARI N G
One bearing required per cond / cone.
One cone required per cord.
Use with: 9162144 CTS40 Cone.
Use with: 9162145 CTS40 Bearing.
To Suit 51 x 57mm headrail.
Ref.
9162145
Ref.
PLUG E N D FOR 40 MM OC TA GON A L T UBE
9162144
C T S40 BRACKET
Use with: 9500736 CTS40 Bracket.
Two brackets required per system.
Pin: Ø8mm.
Use with: 9137018 Plug end and 40mm motor.
To Suit Ø40 Octagonal tube.
To Suit 51 x 57mm headrail.
Ref.
9137018
Ref.
[ 76 ]
9500736
HEADRAIL &
SHAFT ADAPTORS
FOR TILT WIREFREE
Tilt Wirefree
TILT HEADRAIL ADAPTOR 38 X 57
TILT HEADRAIL ADAPTOR 51 X 57
For use with Tilt Wirefree motors to
adapt to a 51 x 57 headbox.
For use with Tilt Wirefree motors to
adapt to a 38 x 57 headbox.
Ref.
9014528
Ref.
TILT SHAF T ADAPTOR D-ROD
T I LT SHAF T ADAPTOR 4 MM SQU ARE
For use with Tilt Wirefree motors to
allow the use of a 4mm square tilt rod.
Ref.
For use with Tilt Wirefree motors to
allow the use of a D shaped tilt rod.
9014540
Ref.
TILT SHAF T ADAPTOR 5MM HEX
For use with Tilt Wirefree motors to
allow the use of a 5mm hex tilt rod.
Ref.
9014529
9014535
[ 77 ]
9014536
HEADRAIL &
SHAFT ADAPTORS
FOR CORD LIFT WIREFREE
Cordlift Wirefree
HEADRAIL ADAPTOR HD EASY GLIDE
HEADRAIL ADAPTOR KENSINGTON
For use with Cordlift Wirefree motors
to adapt to a HD Easy Glide style headrail.
For use with Cordlift Wirefree motors
to adapt to a Kensington style headrail.
Ref.
9013443
Ref.
HEADRAIL ADAPTOR GRABER
HEADRAIL ADAPTOR HD EASY RISE
For use with Cordlift Wirefree motors
to adapt to a Graber style headrail.
For use with Cordlift Wirefree motors to adapt
to a HD Easy Rise style headrail.
Ref.
9013287
Ref.
SHAF T ADAPTOR 4MM SQUARE
For use with Cordlift Wirefree motors to
allow the use of a 5mm hex rod.
9013269
Ref.
SHAF T ADAPTOR SPEARS
9013285
SHAF T ADAPTOR TA PE REEL
For use with Cordlift Wirefree motors to allow
the use of a Comfortex / Kensington Omni-Rise,
Kirsch / Levelor Accordia, Rollease, Graber and
older style Easy Up systems.
Ref.
9013288
SHAF T ADAPTOR 5MM HEX
For use with Cordlift Wirefree motors to
allow the use of a 4mm square rod.
Ref.
9013444
For use with Cordlift Wirefree motors to allow
the use of a Hunter Douglas EasyRise and
Kensington Deluxe systems.
9013283
Ref.
[ 78 ]
9013284
ACCESSORIES
FOR TILT WIREFREE, CORD LIFT WIREFREE
Tilt Wirefree, Cordlift Wirefree
RELOADABLE BATT ERY WAND
RESET PROGRAMMING C ABLE
For use with wirefree motors to program / reset
motor memory.
For use with wirefree motors to power units.
Battery life dependant on installation.
Contact Somfy for approximate life time
based on installation.
Ref.
9013291
Ref.
WALL MOUNT CLIP PACK
For use with wirefree motors to secure battery
wand, ref. 9014020
Ref.
9013263
[ 79 ]
9014020
J5 ACCESSORIES
SHAFT ADAPTORS
6.2mm Hexagonal Shaft adaptor
7.2mm square Shaft adaptor
Compatible with 6.2mm shafts
Compatible with 7.2mm shafts
Also available upto 13.2mm size
Also available upto 12.2mm size
Ref.
9014163
Ref.
9014175
Other Accessories
Switch sensor extension piece
Adjustable Mushroom extension
To extend the upper limit for
Switch
S
sensor extension
all J5 Range
piece has to be fitted with
HTM range to stop upper
limit automatically
Ref.
9014158
Ref.
Black cover for mushroom extension
Also available in white color
Ref.
9014161
[ 80 ]
9014159
J5 ACCESSORIES
HEADRAIL ACCESSORIES
57MM X 51MM HEADRAIL CLIP
58MM X 56MM HEADRAIL CLIP
Stainless steel design used to secure
Stainless steel design used to secure
motor to headrail.
motor to headrail.
Headrail Clip External
Ref.
9014215
Headrail Clip Internal
Ref.
9014216
Ref.
78MM X 67MM HEADRAIL CLIP
9014217
78MM X 67MM HEADRAIL CLIP
Stainless steel design used to secure
Ca
Can be rotated to suit headrail
motor to headrail.
co
configurations
Ref.
9014218
Ref.
65MM X 64MM HEADRAIL ADAPTOR
Can be rotated to suit headrail
configurations
Ref.
9014220
[ 81 ]
9014219
J5 ACCESSORIES
CONNECTING LEAD NEEDED ON DRIVE UNIT SIDE
CONNECTING LEAD WITH A STAS 4 K MAINS LEAD
CONNECTING LEAD WITH A STAS 3 K MAINS LEAD
W 500mm lead length
With
With 500mm lead length
Ref.
9014181
With 900mm lead length
Ref.
9014182
Ref.
9014580
CONNECTING LEAD WITHOUT PLUG
With
Wit 900mm lead length
Ref.
9014184
CABLE SOCKET NEEDED ON CONSTRUCTION SIDE
CABLE SOCKET
CABLE SOCKET
STAK4
STAK3
Ref.
9014185
Ref.
STAS4
STAS3
Ref.
9014187
9014186
Ref.
[ 82 ]
9013713
Curtains
MOTORS & ACCESSORIES
Glydea 35 WT / Glydea 35 DCT ................................. 84
Glydea 60e WT / Glydea 60e DCT ............................ 85
Technical Characteristics
Glydea 35 WT / Glydea 35 DCT
Glydea 60e WT / Glydea 60e DCT ............................. 86
Glydea Accessories ............................................... 87
GLYDEA 35 WT
GLYDEA 35 DCT
MAIN CHARACTERISTICS & FEATURES
Glydea 35 curtain motorization solutions meet the requirements of the most
prestigious projects. Motorized curtains are becoming a common feature of
top-of-the-range projects such as high-quality hotels, luxury homes,
meeting and conference venues.
Glydea 35 is discreet, flexible and robust, offering personalized solutions to
serve your imagination and broaden your horizons.
Large choice of positions for the motor’s hook
Suitable for tracks up to 10m
Touch Motion feature, to open and close the curtain by simply pulling on
the fabric, only with Glydea DCT motor.
My Function, to automatically control the curtain to a preferred position.
2 minutes 30 seconds running time, one direction.
Interchangeable left or right hand mount
Two motor options:
Glydea WT: wired motor
Glydea DCT: dry contact
Possibility of false ceiling mounting
Dirtect AC supply, no adaptor is required.
Compatible with all Somfy RTS receivers.
To choose the right Glydea solution according to your
requirements and for more information, contact us.
A selection chart will be provided on request.
False ceiling mounting
Glydea 35 DCT
Glydea 35 WT
Torque (Nm)
0,6
Speed (cm/s)
20
Ref. 1001261
Torque (Nm)
0,6
Speed (cm/s)
20
Ref. 1001525
Note:
Glydea Range will
be available in
Q3 2010
Information is subject to
change
[ 84 ]
GLYDEA 60e WT
GLYDEA 60e DCT
MAIN CHARACTERISTICS & FEATURES
Glydea 60e curtain motorization solutions meet the requirements of the
most prestigious projects. Motorized curtains are becoming a common
feature of top-of-the-range projects such as high-quality hotels, luxury
homes, meeting and conference venues.
Glydea 60e is discreet, flexible and robust, offering personalized solutions to
serve your imagination and broaden your horizons.
Large choice of positions for the motor’s hook
Suitable for tracks up to 15m
Touch Motion feature, to open and close the curtain by simply pulling on
the fabric
My Function, to automatically control the curtain to a preferred position.
2 minutes 30 seconds running time
Interchangeable left or right hand mount
Two motor options:
Glydea WT: wired motor
Glydea DCT: dry contact
Possibility of false ceiling mounting
Dirtect AC supply, no adaptor is required.
Compatible with all Somfy RTS receivers.
Can be used in tandem, to lift up to 100kg.
False ceiling mounting
To choose the right Glydea solution according to your
requirements and for more information, contact us.
A selection chart will be provided on request.
Glydea 60e DCT
Glydea 60e WT
Torque (Nm)
1
Speed (cm/s)
20
Ref. 1001265
Torque (Nm)
1
Speed (cm/s)
20
Ref. 1001537
Note:
Glydea Range will
be available in
Q3 2010
Information is subject to
change
[ 85 ]
GLYDEA 35 WT & GLYDEA 35 DCT
GLYDEA 60 WT & GLYDEA 60 DCT
TECHNICAL CHARACTERISTICS
MOTOR AND TRACK DIMENSIONS
Control Methods
Glydea 60e WT
Control connector
Glydea 60e DCT
Running time in one direction
Glydea 35 WT
Nominal torque (Nm)
Nominal speed (cm/s)
Noise level (dB)
Protection index
Manual operation
Net weight of the motor (g)
Power consumption (W)
Touch motion
Glydea 35 DCT
TECHNICAL DETAILS
0.6
20
<50
31
Yes
1200
60
No
2min
30s
RJ 12
IR / 2no
or 3no
Dry
contact
0.6
20
<50
31
Yes
1200
60
No
2min
30sec
No
1
20
<50
31
Yes
1200
60
Yes
2min
30s
RJ 12
IR / 2no
or 3no
Dry
contact
1
20
<50
31
Yes
1200
120
No
2min
30sec
No
AC
switch
[ 86 ]
AC
switch
Note:
Glydea Range will
be available in
Q3 2010
Information is subject to
change.
Glydea Accessories
Pulley GA
Motor hook GA for classic curtain
Pulley assembly to put opposite the motor side
with bush bearing
Minimum one for 1-way and two for 2-way
Ref. 1 780 895
Ref. 1 780 897
Drive pulley GA
Pulley Cover GA
Pulley assembly to use on the motor side
with bush bearing
Pulley cover spare part
Ref. 1 780 945
Ref. 1 780 898
Motor Bottom Cover GA
P ulley Stopper Assembly GA
Motor bottom cover spare part
Spare pulley stopper assembly as a kit
Ref. 9 015 579
Ref. 1 780 954
Rail 5m by 6 GA
Swivel ceiling bracket GA
Ceiling bracket to minimize the light gap
(max 2mm)
5m long Glydea track aluminium profile
Ref. 1 780 906
Ref. 1 780 899 / 1 781 379
Rail joint GA
One Touch ceiling bracket GA
To link two rails
For easy installation
Ref. 1 780 891
Ref. 1 780 907
DCT Splitter GlydeaTM
RTS 433 receiver GlydeaTM
Ref. 9 015 442
Ref. 1 870 172
10 mm belt 100m ro
roll GA
Adjustable Wall Mount Bracket GA
Bracket with minimum 100mm projection
and 34 mm extension, to use with swivel
or one touch ceiling bracket
T5 timing belt with 5 steel core tension cord,
with textile on the back and the tooth
Ref. 1 780 909
Ref. 1 780 900
Double Adjustable Wall Mount Bracket GA GA
Cushion
shion for
f r belt G
fo
GA
Rubber part to be positionned in the
assembled track to prevent the belt off
splitted track transported folded
Wall bracket to mount 2 rails equiped with
swivel or one touch ceiling bracket. 200mm
projection and 44 mm extension
Ref. 1 780 955
Ref. 1 780 910
[ 87 ]
Glydea Accessories
Accessories for “classic” curtain
with Flexible master carrier / heavy duty master carrier
Master carrier GA 35
Overlap Arm GA 35
Maximum load 35 kg for 6m track
Ref. 1 780 890
Ref. 1 780 893
Straight Arm GA 35
Rotating Eye Runner GA
1.5 kg maximum load
Ref. 1 780 994
Ref. 1 780 892
Heavy Duty Overlap Arm Kit GA
Heavy duty master carrier GA
Stainless steel with roller
Maximum load 35 kg for 6m track
Ref. 1 781 4 17
Ref. 1 781 344
Heavy Duty Straight Arm GA
High Perf Rotating Eye Runner
Stainless steel
1.5 kg maximum load
Ref. 1 781 4 16
Ref. 1 781 415
ACCESSORIES FOR “RIPPLE” CURTAIN with Heavy Duty Master Carrier
Ripple runner 1 7/8 GA (48mm)
Ripple runner 2 1/8 GA (54mm)
Runner mounted on wheels for 120% fullness
ripple curtains
Runner mounted on wheels for 100% fullness
ripple curtains
Ref. 1 780 901
Ref. 1 780 902
Ripple runner 2 3/8 GA (60mm)
Ripple straight arm
Runner mounted on wheels for 80% fullness
ripple curtains
Stainless steel
Ref. 1 780 946
Ref. 1 780 903
Ripple Overlap arm Kit
Ripple
p Butt
utt Arms Kit
Stainless steel
Stainless steel
Ref. 1 780 947
Ref. 1 780 953
Ripple Motor Hook GA
Minimum one for 1-way and two for 2-way
Ref. 1 780 905
ELECTRICAL ACCESSORIES
DCT 2,5 m Cable Glydea
RJ9 / RJ12 Adapter
Cable equipped with a RJ 12 connector
Necessary to adapt IR3 ILT sensor
Ref. 9 015 443
Ref.9 014 068
[ 88 ]
[ 89 ]
Awnings
MOTORS & ACCESSORIES
Motor Selection Chart .......................................... 91
Altus 50 RTS & Altus 60 RTS .................................... 93
reaO 50 RTS & Orea 60 RTS .................................... 95
reaO 50 WT & Orea 60 WT ...................................... 97
50LT& LT60 ...................................................... 99
50LTCSI & LT60 CSI .............................................. 101
50LTCSI RTS ..................................................... 103
Phoenix ........................................................ 105
Adaptors - 50mm, 60mm Motors ........................... 107
Motor Brackets - 50, 60mm CSI Motors ..................... 110
Bearings - 50, 60mm Motors................................. 112
Plug End Brackets - 50, 60mm Motors ..................... 113
CSI Accessories - 50, 60mm CSI Motors...................... 114
Phoenix Accessories ............................................ 115
ables
C ............................................................. 116
FOLDING ARM AWNING
MOTOR SELECTION CHART
Tube Diameter (mm)
Tube Diameter (mm)
Tube Diameter (mm)
Tube Diameter (mm)
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
Refer to the chart that corresponds to the projection required.
Select the tube size from the left hand column.
Select the motor suitable by matching the arms & tube size together.
A safety factor has already been incorporated.
Installation length shown in metres.
Number of Arms -->
2
4
6
8
Installation length (m) -->
6
12
15
20
ø 63/70
ø 78
40
50
60
80
Nm
Nm
Nm
Nm
30/35
40
60
Nm
Nm
Nm
8
Installation length (m) -->
6
12
15
20
50
80
80
100
Nm
Nm
Nm
Nm
30/35
40
60
Nm
Nm
Nm
8
Installation length (m) -->
6
12
15
20
40
50
80
Nm
Nm
Nm
Nm
50
80
100
120
Nm
Nm
Nm
Nm
2
4
6
8
Installation length (m) -->
6
12
15
20
5o
8o
Nm
Nm
Nm
8o
100
120
Nm
Nm
Nm
100
25 Nm
30 Nm
35 Nm
40 Nm
50 Nm
LT 50 Gemini
Altus 50 25Nm
Orea 50 25Nm
Gemini CSI
LT 50 Helios
Orea WT 30Nm
Helios CSI RTS
Orea 50 35Nm
LT 50 Mariner
Orea WT 40Nm
Orea 50 40Nm
Mariner CSI
Mariner CSI RTS
LT 50 Vectran
Orea 50 50Nm
Orea WT 50Nm
Vectran CSI RTS
60 Nm
80 Nm
100 Nm
120 Nm
LT 60 Vega
Altus 60 60Nm
Vega CSI
LT 60 Sirius
Sirius CSI
LT 60 Titan
Altus 60 100Nm
Orea 60 100Nm
Orea WT 100Nm
Titan CSI
LT 60 Taurus
Altus 60 120Nm
Taurus CSI
■ Projection up to 3m
10
12
25
30
100
Number of Arms -->
ø50 Motor
Designation
30
40
6
Torque -->
12
25
Nm
4
ø 78
10
25
2
ø 63/70
■ Projection up to 2m
Nm
Number of Arms -->
ø 78
30
25
6
ø 63/70
12
25
Nm
4
ø 78
10
25
2
ø 63/70
■ Projection up to 1.5m
Nm
Number of Arms -->
Torque -->
ø60 Motor
Designation
HOW TO USE THIS SELECTION CHART
•
•
•
•
•
[ 91 ]
■ Projection up to 5m
10
12
25
30
DROP ARM AWNING
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Refer to the chart that corresponds to the number of arms to be
used in the system.
• Select the drop from the left hand column.
• Select the motor suitable by matching the width & drop together.
• A safety factor has already been incorporated.
• Installation sizes shown in metres.
■ 2 Arms
Total Width
(metres) -->
1.2
1.5
1.8
1.4
2.4
2.7
3.0
3.3
3.6
20 Nm
1.7
Drop - (metres)
2.1
3.9
4.5
4.8
5.1
5.4
5.7
6.0
25 Nm
20 Nm
25 Nm
2.0
20 Nm
25 Nm
2.3
20 Nm
25 Nm
2.6
4.2
20 Nm
25 Nm
■ 4 Arms
Total Width
(metres) -->
1.2
1.5
1.8
1.4
Drop - (metres)
2.7
3.0
3.3
3.6
3.9
40 Nm
30 Nm
40 Nm
2.0
30 Nm
40 Nm
2.3
30 Nm
40 Nm
2.6
ø50 Motor
Designation
2.4
30 Nm
1.7
Torque -->
2.1
30 Nm
40 Nm
20 Nm
25 Nm
30 Nm
40 Nm
LT 50 Meteor
Meteor CSI RTS
LT 50 Gemini
Altus 50 25Nm
Gemini CSI
LT 50 Helios
Helios CSI RTS
LT 50 Mariner
Mariner CSI
Mariner CSI RTS
[ 92 ]
4.2
4.5
4.8
5.1
5.4
5.7
6.0
ALTUS 50 RTS
ALTUS 60 RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Altus RTS (Radio Technology Somfy) is suitable for a wide range of awning
applications. Available in torques from 25Nm (50mm) to 120Nm (60mm) and coupled
with its 48mm or 60mm (respectively) design, it is adapted for Ø50 tubes and above.
A built-in radio receiver with Somfy’s rolling code for RTS control, the Altus RTS
allows the user to operate almost any application with the convenience of a
remote control.
Remote set limits.
Turning capacity limited only by thermal time.
Suitable for tubes: Ø50 to Ø85.
Memory Capacity: 12 transmitters, plus 3 sensors.
Programmable “my” position.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
Torque (Nm)
25
Speed (RPM)
17
Ref.
1043170
ALTUS RTS 70/17
Torque (Nm)
70
Speed (RPM)
17
Ref.
1163103
ALTUS RTS 100/12
ALTUS RTS 120/12
Torque (Nm)
100
Speed (RPM)
12
Ref.
1166047
Torque (Nm)
120
Speed (RPM)
12
Ref.
1167039
ALTUS RTS 25/17
60mm
[ 93 ]
ALTUS 50 RTS
ALTUS 60 RTS
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active
Yellow /Green = Earth
L1
L2
3.95
Ø 47
50mm
17.15
min
25
Ø 63
20
L1
L2
7.5
Ø 60
60mm
17
min
23
34
ALTUS RTS 25/17
ALTUS RTS 70/17
ALTUS RTS 100/12
ALTUS RTS 120/12
®
L1 (mm)
655
734
734
734
L2 riveting distance (mm)
640
717
717
717
Torque (Nm)
25
70
100
120
Speed (rpm)
17
17
12
12
Rated Voltage (V)
230
230
230
230
Rated Power consumption (W)
170
350
350
400
Rated Current (A)
0.8
1.5
1.5
1.8
4
4
4
4
Thermal cut off temp (°C)
150
130
130
140*
Average running noise (dbA)
56
66
65
65
Running time before thermal cut off (min)
50 x 1.5
63 x 1.5
63 x 1.5
63 x 1.5
Motor weight (kg)
2.34
4.50
4.82
5.03
Cable length (M)
3
3
3
3
Number of cores in cable
3
3
3
3
Cross section of cable (mm²)
0.75
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
IP44
Minimum tube diameter
Normal functioning temperature: -10°C to +40°C
Ø 63
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
* Thermal protection will not automatically reset. Power off then on the motor to reset.
[ 94 ]
OREA 50 RTS
OREA 60 RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Orea 50 / 60 RTS is suitable for awning application types that require the use of
a sealed cassette box. Available in torques from 25Nm (Orea 50) to 100Nm (Orea 60),
coupled with its flexible 48mm (Orea 50) or 60mm (Orea 60) design, it is adapted for
Ø50mm tubes and above. A built-in radio receiver with Somfy’s rolling code and over
torque upper limit functionality are integrated to provide a tightly sealed headbox.
Installation flexibility of remote control make the Orea 50 / 60 RTS ideal for cassette
style awnings.
Remote set limits with auto set over torque upper limit.
Turning capacity limited only by thermal time.
Suitable for tubes: Ø50 to Ø85.
Memory Capacity: 12 transmitters, plus 3 sensors.
Programmable “my” position.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
OREA RTS
OREA RTS
OREA RTS
OREA RTS
25/17
35/17
40/17
50/12
Torque (Nm)
25
Speed (RPM)
17
Ref.
1114130
Torque (Nm)
35
Speed (RPM)
17
Ref.
1116125
Torque (Nm)
40
Speed (RPM)
17
Ref.
1117119
Torque (Nm)
50
Speed (RPM)
12
Ref.
1118090
Torque (Nm)
55
Speed (RPM)
17
Ref.
1181068
Torque (Nm)
85
Speed (RPM)
17
Ref.
1183057
Torque (Nm)
100
Speed (RPM)
12
Ref.
1184058
60mm
OREA RTS 55/17
OREA RTS 85/17
OREA RTS 100/12
[ 95 ]
OREA 50 RTS
OREA 60 RTS
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active
Yellow /Green = Earth
L1
L2
3.95
Ø 47
50mm
25
17.15
min
Ø 63
20
L1
L2
Ø 60
60mm
17
min
23
7.5
34
OREA 60 RTS 55/17
OREA 60 RTS 85/17
OREA 60 RTS 100/12
675
745
675
734
734
734
660
730
660
717
717
717
Torque (Nm)
25
35
40
50
55
85
100
OREA 50 RTS 40/17
655
640
OREA 50 RTS 35/17
L1 (mm)
L2 riveting distance (mm)
OREA 50 RTS 25/17
OREA 50 RTS 50/12
®
Speed (rpm)
17
17
17
12
17
17
12
Rated Voltage (V)
230
230
230
230
230
230
230
Rated Power consumption (W)
170
240
270
240
290
400
350
Rated Current (A)
0.8
1.1
1.2
1.1
1.25
1.8
1.5
4
4
4
4
4
4
4
Thermal cut off temp (°C)
150
150
140
150
130
140*
130
Average running noise (dbA)
56
56
57
55
64
66
65
Running time before thermal cut off (min)
50 x 1.5
50 x 1.5
50 x 1.5
50 x 1.5
63 x 1.5
63 x 1.5
63 x 1.5
Motor weight (kg)
2.34
2.56
2.85
2.585
4.18
4.70
4.82
Cable length (M)
3
3
3
3
3
3
3
Number of cores in cable
3
3
3
3
3
3
3
Cross section of cable (mm²)
0.75
0.75
0.75
0.75
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
IP44
IP44
IP44
IP44
Minimum tube diameter
Normal functioning temperature: -10°C to +40°C
Ø 63
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
* Thermal protection will not automatically reset. Power off then on the motor to reset.
[ 96 ]
OREA 50 WT
OREA 60 WT
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The Orea 50 / 60 WT is suitable for awning applications that require the use of a
sealed cassette box. Available in torques from 25Nm to 100Nm, coupled with its flexible
48mm or 60mm (respectively) design, it is adapted for Ø50mm tubes and above.
Electronically set limits and the adaptability of 230V control plus over torque upper
limit functionality for a tightly sealed headbox make the Orea 50 / 60 WT
ideal for cassette style awnings.
Remote set limits with auto set over torque upper limit.
Turning capacity limited only by thermal time.
Suitable for tubes: Ø50 to Ø85.
230V switch control via mechanical or electronic means.*
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
OREA
OREA
OREA
OREA
WT
WT
WT
WT
25/17
35/17
40/17
50/12
Torque (Nm)
25
Speed (RPM)
17
Ref.
1114171
Torque (Nm)
35
Speed (RPM)
17
Ref.
1116171
Torque (Nm)
40
Speed (RPM)
17
Ref.
1117161
Torque (Nm)
50
Speed (RPM)
12
Ref.
1118122
Torque (Nm)
55
Speed (RPM)
17
Ref.
1181186
Torque (Nm)
85
Speed (RPM)
17
Ref.
1183148
Torque (Nm)
100
Speed (RPM)
12
Ref.
1184082
60mm
OREA WT 55/17
OREA WT 85/17
OREA WT 100/12
*Direct switching of a 230V motor must always be done via a mechanical interlock.
[ 97 ]
OREA 50 WT
OREA 60 WT
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active 1
Black = Active 2
Green/Yellow = Earth
L1
50mm
3.95
Ø 47
L2
25
17.15
min
Ø 63
20
L1
60mm
7.5
Ø 60
L2
17
min
23
34
OREA WT 55/17
OREA WT 85/17
OREA WT 100/12
675
745
675
734
734
734
660
630
660
717
717
717
Torque (Nm)
25
35
40
50
55
85
100
OREA WT 40/17
655
640
OREA WT 35/17
L1 (mm)
L2 riveting distance (mm)
OREA WT 25/17
OREA WT 50/12
®
Speed (rpm)
17
17
17
12
17
17
12
Rated Voltage (V)
230
230
230
230
230
230
230
Rated Power consumption (W)
170
240
270
240
240
400
350
Rated Current (A)
0.8
1.1
1.2
1.1
1.25
1.8
1.5
4
4
4
4
4
4
4
150
150
140
150
130
160*
130
Running time before thermal cut off (min)
Thermal cut off temp (°C)
56
56
57
55
64
66
65
50 x 1.5
50 x 1.5
50 x 1.5
50 x 1.5
63 x 1.5
63 x 1.5
63 x 1.5
Motor weight (kg)
2.20
2.55
2.8
2.75
4.39
5.03
4.83
Cable length (M)
3
3
3
3
3
3
3
Number of cores in cable
4
4
4
4
4
4
4
Average running noise (dbA)
Minimum tube diameter
Cross section of cable (mm²)
0.75
0.75
0.75
0.75
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
IP44
IP44
IP44
IP44
Normal functioning temperature: -10°C to +40°C
Ø 63
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
* Thermal protection will not automatically reset. Power off then on the motor to reset.
[ 98 ]
LT50
LT60
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The LT50 / LT60 motors are suitable for a wide range of awning applications.
Available in torques from 25Nm to 120Nm and with its flexible 48mm or 60mm
(respectively) design, it is adapted for Ø50mm tubes and above. Rapid set push
button limits and the availability of a wide range of 230v controllers make the LT50
and LT60 suitable all round performers.
Rapid set limits.
46 turn limit capacity (LT60 35 turn capacity).
Suitable for tubes: Ø50 to Ø85.
230V switch control via electronic or mechanical means*.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
GEMINI 25/17
HELIOS 30/17
MARINER 40/17
VECTRAN 50/12
Torque (Nm)
25
Speed (RPM)
17
Ref.
1043037
Torque (Nm)
30
Speed (RPM)
17
Ref.
1045041
Torque (Nm)
40
Speed (RPM)
17
Ref.
1049065
Torque (Nm)
50
Speed (RPM)
12
Ref.
1051029
Torque (Nm)
60
Speed (RPM)
12
Ref.
1162023
Torque (Nm)
80
Speed (RPM)
12
Ref.
1164021
Torque (Nm)
100
Speed (RPM)
12
Ref.
1166025
Torque (Nm)
120
Speed (RPM)
12
Ref.
1167017
60mm
VEGA 60/12
SIRIUS 80/12
TITAN 100/12
TAURUS 120/12
* Parallel wiring of motors is prohibited without the use of an isolation control, eg. 4AC Motor Controller,
4 Motor Group Controller etc. Direct switching of a 230V motor must always be done via a mechanical interlock.
[ 99 ]
LT50
LT60
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active 1
Black = Active 2
Green/Yellow = Earth
24
L1
L2
50mm
Ø 74
Ø 47
®
25
Ø 63
20
L1
L2
7.5
Ø 60
60mm
34
17
min
23
24
Ø 78
GEMINI 25/17
HELIOS 30/17
MARINER 40/17
VECTRAN 50/12
VEGA 60/12
SIRIUS 80/12
TITAN 100/12
TAURUS 120/12
®
L1 (mm)
555
605
655
605
614
614
659
659
L2 riveting distance (mm)
540
590
640
590
597
597
642
642
Torque (Nm)
25
30
40
50
60
80
100
120
Speed (rpm)
17
17
17
12
12
12
12
12
Turn Capacity
46
46
46
46
35
35
35
35
Ø 63
Rated Voltage (V)
230
230
230
230
230
230
230
230
Rated Power consumption (W)
170
240
270
240
280
320
410
450
Rated Current (A)
0.8
1.1
1.2
1.1
1.25
1.5
1.9
2.1
4
4
4
4
4
4
4
4
Thermal cut off temp (°C)
150
150
140
150
140
150
150
150*
NOTE
Average running noise (dbA)
56
55
57
55
65
65
65
65
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Running time before thermal cut off (min)
50 x 1.5
50 X 1.5
50 x 1.5
50 x 1.5
63 x 1.5
63 x 1.5
63 x 1.5
63 x 1.5
Motor weight (kg)
2.2
2.55
2.8
2.55
3.92
4.19
4.68
4.45
Cable length (M)
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
Number of cores in cable
4
4
4
4
4
4
4
4
Cross section of cable (mm²)
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
IP44
IP44
IP44
IP44
IP44
Minimum tube diameter
Normal functioning temperature: -10°C to +40°C
* Thermal protection will not automatically reset. Power off then on the motor to reset.
[ 100 ]
LT50 CSI
LT60 CSI
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The CSI (manual override) motor is suitable for awnings that require the added
flexibility of manual crank operation. Available in torques from 25Nm (50mm) to
120Nm (60mm) the CSI’s manual override function allows the versatility of operation
even if power is not present. With utilisation of the same adaptors as the
50 and 60mm range and rapid set push button limits, the CSI motor is a great
hardwired option for areas that are prone to power loss.
Rapid set limits.
34 turn limit capacity.
Suitable for tubes: Ø50 to Ø85.
230V switch control via electronic or mechanical means*.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
GEMINI 25/17
MARINER 40/17
VECTRAN 50/12
Torque (Nm)
25
Speed (RPM)
1043001
40
Speed (RPM)
17
17
Ref.
Torque (Nm)
Ref.
1049011
Ref.
1051000
Torque (Nm)
50
Speed (RPM)
12
Torque (Nm)
60
Speed (RPM)
12
Ref.
1162002
Torque (Nm)
80
Speed (RPM)
12
Ref.
1164003
Torque (Nm)
100
Speed (RPM)
12
Ref.
1166002
Torque (Nm)
120
Speed (RPM)
12
Ref.
1167003
60mm
VEGA 60/12
SIRIUS 80/12
TITAN 100/12
TAURUS 120/12
* Parallel wiring of motors is prohibited without the use of an isolation controller, eg. 4AC Motor Controller,
4 Motor Group Controller, etc. Direct switching of a 230V motor must always be done via a mechanical interlock.
[ 101 ]
LT50 CSI
LT60 CSI
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active 1
Black = Active 2
Green/Yellow = Earth
.
L1
L2
40
.
54
94
Ø 48
40
50mm
80
24
.
86
®
31
2 Holes
at ø 6.4
86 apart
.
L1
L2
80
40
39
®
.
86
54
94
Ø 60
40
60mm
24
VEGA 60/12
SIRIUS 80/12
594
664
646
646
681
681
579
649
630
630
665
665
Torque (Nm)
25
40
60
80
100
120
Speed (rpm)
17
17
12
12
12
12
Turn Capacity
34
34
34
34
34
34
TAURUS 120/12
MARINER 40/17
L1 (mm)
L2 riveting distance (mm)
TITAN 100/12
GEMINI 25/17
2 Holes
at ø 6.4
86 apart
Rated Voltage (V)
230
230
230
230
230
230
Rated Power consumption (W)
170
270
240
290
350
400
Rated Current (A)
0.8
1.2
1.05
1.25
1.5
1.8
4
4
4
4
4
4
150
140
140
130
130
140*
Running time before thermal cut off (min)
Thermal cut off temp (°C)
56
57
65
65
65
65
50 x 1.5
50 x 1.5
63 x 1.5
63 x 1.5
63 x 1.5
63 x 1.5
Motor weight (kg)
2.81
3.38
4.67
4.93
5.4
5.56
Cable length (M)
2.5
2.5
2.5
2.5
2.5
2.5
Number of cores in cable
4
4
4
4
4
4
Cross section of cable (mm²)
0.75
0.75
0.75
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
IP44
IP44
IP44
Average running noise (dbA)
Minimum tube diameter
Normal functioning temperature: -10°C to +40°C
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
* Thermal protection will not automatically reset. Power off then on the motor to reset.
[ 102 ]
.
LT50 CSI RTS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor
The CSI (Manual Override) RTS (Radio Technology Somfy) motor is suitable for a
wide range of awning application types. Available in torques from 20Nm to 50Nm,
the CSI’s manual override function allows the versatility of operation even if power
is not present*. With utilisation of the same adaptors as the 50mm range, rapid set
push button limits and RTS functionality, the CSI motor is a great remote option for
areas that are prone to power loss.
Rapid set limits.
34 turn limit capacity.
Suitable for tubes: Ø50 to Ø85.
Memory capacity: 12 transmitters, plus 3 sensors.
2 programmable "my" positions.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
50mm
METEOR CSI RTS 20/17
HELIOS CSI RTS 30/17
MARINER CSI RTS 40/12
VECTRAN CSI RTS 50/12
Torque (Nm)
20
Speed (RPM)
17
Ref.
1041023
Torque (Nm)
30
Speed (RPM)
17
Ref.
1045023
Torque (Nm)
40
Speed (RPM)
12
Ref.
1049037
Torque (Nm)
50
Speed (RPM)
12
Ref.
1051017
* RTS functionality is not available if power is lost to the motor.
[ 103 ]
LT50 CSI RTS
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active
Yellow /Green = Earth
L1
L2
Ø 48
50mm
24
.
31
.
80
774
774
774
774
759
759
759
759
Torque (Nm)
20
30
40
50
Speed (rpm)
17
17
12
12
Turn Capacity
34
34
34
34
Rated Voltage (V)
230
230
230
230
Rated Power consumption (W)
160
240
240
240
Rated Current (A)
0.75
1.1
1.1
1.1
4
4
4
4
Thermal cut off temp (°C)
150
150
150
150
Average running noise (dbA)
53
55
55
57
Running time before thermal cut off (min)
50 x 1.5
50 x 1.5
50 x 1.5
50 x 1.5
Motor weight (kg)
2.96
3.21
3.21
3.21
Cable length (M)
2.5
2.5
2.5
2.5
Number of cores in cable
3
3
3
3
Cross section of cable (mm²)
0.75
0.75
0.75
0.75
Index Protection
IP44
IP44
IP44
IP44
Minimum tube diameter
54
VECTRAN CSI RTS 50/12
86
MARINER CSI RTS 40/12
HELIOS CSI RTS 30/17
L1 (mm)
L2 riveting distance (mm)
®
METEOR CSI RTS 20/17
94
40
40
2 Holes
at ø 6.4,
86 apart
NOTE
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
Normal functioning temperature: -10°C to +40°C
[ 104 ]
.
PHOENIX
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz shaft drive motor.
The Phoenix motor has long been used to motorise greenhouse louvres
and as a retrofit to older style folding arm awnings that are normally
operated via a crank handle. Still utilising a manual override operation
when needed the Phoenix motor is a high torque, shaft driving, enclosed
unit. With it’s unique design it allows for a relatively simple fit to an
existing awning.
Progressive limits.
38 turn limit capacity.
Suitable for: 13, 14 and 19mm square shafts.†
230V switch control via electronic or mechanical means.*
Requires the use of adaptors depending on drive method.
Vertical mount only.
Intermittent Usage.
PHOENIX 50/12
Torque (Nm)
50
Speed (RPM)
12
Ref.
1205001
*Parallel wiring of motors is prohibited without the use of an isolation controller, eg. 4AC Motor Controller,
4 Motor Group Controller, etc. Direct switching of a 230V motor must always be done via a mechanical interlock.
†Adaptors required for 13mm and 14mm shafts.
[ 105 ]
PHOENIX
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active 1
Black = Active 2
Green/Yellow = Earth
277
204
49
9
171
PHOENIX 50/12
61
Torque (Nm)
50
Speed (rpm)
12
Turn Capacity
38
Rated Voltage (V)
230
Rated Power Consumption (W)
390
Rated Current (A)
1.85
Running time before thermal cut off (min)
Thermal cut off temp (°C)
5
Average running noise (dbA)
63
Motor weight (kg)
5.5
Cable length (M)
2.5
Number of cores in cable
NOTE
140
Information about the
noise is according to
Somfy measures and is for
information only. Taken as
the worst value in load, for
the up direction during the
first 10 seconds of travel.
4
Cross section of cable (mm²)
0.75
Index Protection
IP33
Normal functioning temperature: -10°C to +40°C
[ 106 ]
▼
ADAPTORS
50mm,
60mm MOTORS
▼
50mm
Tube
Profile
Wheel
Crown
1,5
ø60 x 1.5
Round
Wheel
Ref.
9751013
Crown
Ref.
9707033
Wheel
Ref.
9751013
Crown
Ref.
9707029
Wheel
Ref.
9751002
Crown
Ref.
9707030
Wheel
Ref.
9751002
Crown
Ref.
9707030
Wheel
Ref.
9751005
Crown
Ref.
9707034
60
2
ø60 x 2.0
Round
60
Issey
ø63
63
Sunmaster
ø65
Rochling,
Perma,
Turnils
ø70
[ 107 ]
▼
ADAPTORS
50mm,
60mm MOTORS
▼
50mm
Tube
Profile
Wheel
Crown
Imbac
ø70
Franciaflex
ø70
Perma, HD,
Turnils
ø70
1
Dohner,
Issey,
Turnils
ø78
Issey
ø85
Wheel
Ref.
9751005
Crown
Ref.
9128424
Wheel
Ref.
9410303
Crown
Ref.
9128429
Wheel
Ref.
9761011
Crown 1
Ref.
9707026
Crown 2
Ref.
9277167
Wheel
Ref.
9761001
Crown
Ref.
9707027
Wheel
Ref.
9761003
Crown
Ref.
9707035
2
Ø 78
85
[ 108 ]
▼
ADAPTORS
50mm,
60mm MOTORS
▼
60mm
Tube
Profile
Wheel
Crown
1,5
Wheel
Ref.
9206019
Wheel
Ref.
9761011
Crown
Ref.
9277167
Wheel
Ref.
9761010
Crown
Ref.
9700978
Wheel
Ref.
9761005
Crown
Ref.
9701051
Wheel
Ref.
9761001
Crown
Ref.
9705341
Wheel
Ref.
9761003
Crown
Ref.
9707641
Wheel
Ref.
9420300
Crown
Ref.
9690085
No Crown
Adaptor
Required
Ø63
Round
63
Perma, HD,
Turnils
ø70
Schenker
ø75
Dohner,
Turnils
ø78
Dohner,
Aluxor,
Issey,
ø78
Dohner,
Issey
ø85
Ø 85
1,2
Imbac
ø85
12
85
[ 109 ]
MOTOR BRACKETS
50mm,
60mm MOTORS
▼
50mm, 60mm
68
UNIVERSAL ZAMACK BRACKET
Three points for fixing bolts:
- m6, 44mm and 48mm.
157
110
Fix Points:
- 2 holes Ø6mm, 48mm apart.
HIGH LOAD BRACKET 50/60mm
- m8, 60mm.
- 2 holes Ø8mm, 60mm apart with bolt head.
Dimensions: 157h x 120w x 60d.
60
- 2 holes Ø8mm, 60mm apart.
120
Ref.
30
Maximum Torque: 85 Nm
9910000
UNIVERSAL ZAMACK THREADED
Threaded holes for fixing bolts:
-m6, 48mm apart.
-m8, 60mm apart.
-2 holes Ø8mm, 60mm apart with bolt head.
Maximum Torque: 85 Nm
Ref.
9910001
UNIVERSAL ZAMACK BRACKET WITH LOCKING RING
Fix Points:
-2 holes Ø6mm, 48mm apart.
-2 holes Ø8mm, 60mm apart.
-2 holes Ø8mm, 60mm apart with bolt head.
Maximum Torque: 120 Nm
Ref.
9910003
[ 110 ]
Maximum Torque: 120 Nm
Ref.
9430601
MOTOR BRACKETS
50mm CSI,
60mm CSI MOTORS
▼
50mm CSI, 60mm CSI
UNIVERSAL FIX POSITION BRACKET
SQUARE BRACKETS WITH MULTIPLE FIXING POINTS
Three point mounting:
- m6, 86mm apart.
Two point Motor fixng.
- m6, 48mm with a point for 120° positioning.
Square Bracket with multiple fixing points
Three threaded bracket mounting points:
- m6, 44mm and 48mm apart .
- m8, 60mm apart.
- 2 holes, 60mm & 44mm apart with bolt head.
Maximum Torque: 50 Nm
Maximum Torque: 120 Nm
Ref.
9910040
Ref.
9410658
30˚ FIX POSITION BRACKET
LT TO CSI BRACKET
Three point mounting:
- m6, 86mm apart.
30° motor fixing.
Allows for the use of a Zamack bracket
with a CSI motor.
Fixed with two supplied screws.
Use with ref. 9910001, 9910000.
Maximum Torque: 85 Nm
Ref.
Maximum Torque: 85 Nm
9910051
Ref.
[ 111 ]
9420654
▼
PLUG END BRACKETS
50mm,
60mm MOTORS
50mm, 60mm
HOL DE R FOR B ALL
NY LON BA LL
For use with ball ref: 9028665.
Ø12 bore.
For use with holder ref: 1781030.
Maximum Torque: 50 Nm
Ref.
Maximum Torque: 50 Nm
9685181
1781030
Ref.
HIGH LOAD INTERMEDIATE SUPPORT
HIGH LO AD PLUG END BRACKET
Four wheels to suit the tube being used are
required with this bracket.
(see adaptors section).
Adjustable saddle holder to suit: 9420674.
Dimensions: 157h x 120w x 60d.
Maximum Torque: 120 Nm
Ref.
9685181
9028665
Maximum Torque: 120 Nm
9685181
9420673
Ref.
[ 113 ]
9685181
9430603
PHOENIX ACCESSORIES
PHOENIX MOTOR
▼
PHOE N I X AN GLE B RACK E T
SQUARE PLUG END BRACKET
Adjustable position angle bracket for
Phoenix motor.
Painted in Epoxy colour cream.
Dimensions: 190h x 124w x 50d.
Mounting bracket with locking screw
for nylon bearing.
For use with ref. 1781015.
Maximum Torque: 55 Nm
Ref.
9129686
Ref.
BUSH ADAPTOR 13mm
BUSH ADAPTOR 14mm
For use with Phoenix Motor.
Allows for a 13mm shaft to be used with
the standard 19mm drive.
For use with Phoenix motor.
Allows for a 14mm shaft to be used with
the standard 19mm drive.
Maximum Torque: 55 Nm
Ref.
Maximum Torque: 55 Nm
9129576
Ref.
N YLON B E ARI N G
Ø12 bearing for Phoenix motor used
with end bracket.
For use with ref. 9127808.
Maximum Torque: 55 Nm
Ref.
9127808
1781015
PHOENIX EXPLODED DIAGRAM
[ 115 ]
9129577
▼
CABLES
NOTE: It is important to observe local wiring
regulations before fitting Somfy Motors.
HIRSCHMANN CONNEC TOR FOR SUPPLY (BL ACK)
HIRSCHMANN CONNEC TOR FOR MOTO R (BL ACK)
Detachable high protection connector: 3 terminals + earth.
IP54 rating.
Weight: 30g.
Connectors can be fitted to RTS and WT cables.
Supplied not connected.
Ref. 9686064
Detachable high protection connector: 3 terminals + earth.
IP54 rating.
Weight: 30g.
Connectors can be fi tted toRTS and WT cables.
Supplied not connected.
Ref. 9686065
H I - P R O M OTOR C A BL E V V F W H I T E
VVF white cable.
Four cores (blue, black,
brown and green/ yellow).
0.75mm² cross section.
Suitable for LT 50/ 60 motors.
Ref.
Length.
9203802
2.5m
9203804
5m
9203805
10m
H I - P R O M OTOR C A BL E R R F BL ACK
RRF black cable. Four cores (blue,
black, brown and green/ yellow).
0.75mm² cross section.
Suitable for LT 50/ 60 motors.
Ref.
Length.
9203834
3m
9203839
10m
RT S M OTOR C A BL E V V F W H I T E
VVF white cable. Three cores
(blue, brown and green/ yellow).
0.75mm² cross section.
Suitable for RTS 50/ 60 motors.
Ref.
Length.
9001647
3m
9001648
5m
9001659
10m
[ 116 ]
▼
CABLES
NOTE: It is important to observe local wiring
regulations before fitting Somfy Motors.
RT S M OTOR C A BL E R R F BL ACK
RRF black cable. Three cores
(blue, brown and green/ yellow).
0.75mm² cross section.
Suitable for RTS 50/ 60 motors.
Ref.
Length.
9001654
3m
C S I M OTOR C A BL E V V F W H I T E
VVF white cable. Four cores (blue,
black, brown and green/ yellow).
0.75mm² cross section.
Suitable for C.S.I 50/ 60 motors.
Ref.
Length.
9208282
2.5m
TEST LEAD
TEST LEAD FOR RT S MOTORS
For use with RTS motors.
3m cable with quick clip connectors.
Power illumination.
Ref.
9686071
[ 117 ]
[ 118 ]
Windows, Louvres,
Domes
MOTORS & ACCESSORIES
Motor Selection Charts:
Top and Bottom Opening Windows - Linkeo ............. 120
Bottom Opening Windows - Rodeo ......................... 121
Skylights - Linkeo .............................................. 122
Domes - Rodeo ................................................ 123
Louvres - Rodeo ............................................... 124
Linkeo 2.......................................................... 125
Linkeo 4 ......................................................... 127
Rodeo ............................................................ 129
Motor Brackets - Linkeo & Rodeo ........................... 131
LINKEO
TOP & BOTTOM OPENING WINDOWS
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the height of the window.
• Follow the column down and select the desired opening amount.
• Below the opening, the required power rating from the motor will be shown.
• Use the opening and the power required from the chart to select the
appropriate motor from the list below.
height of the window
500mm - 1000mm
1000mm - 2000mm
2000mm - 2500mm
desired opening (mm)
200
250
250
420
420
600
835
power required (N)
200
200
200
400
400
400
400
NOTE: Calculation of the power required is based on the most common systems on the market. For an exact calculation use the below formula.
W = width of the window
F = needed force in Kg
S
H
F
G
S = desired stroke in mm
F
H
S
W
W
G
H = height of the window in mm
G = weight of the window in Kg
F=
S
G
x
H
2
F x 10*
= Motor required
Torque -->
200N
400N
LINKEO DC
Motor
Designation
(Round up to the nearest N motor)
Linkeo DC 200mm
Linkeo DC 420mm
Linkeo DC 250mm
Linkeo DC 600mm
Torque -->
200N
400N
LINKEO AC
Motor
Designation
Linkeo DC 835mm
Linkeo AC 200mm
Linkeo AC 420mm
Linkeo AC 250mm
Linkeo AC 600mm
NOTE: Linkeo 835mm only available in DC
[ 120 ]
• The width (W) of the window must
not exceed 1500mm and must be at
minimum 500mm.
• The height (H) of the window must
be at least twice the size of the
desired opening, keep in mind the
maximum sag of the chain.
*As a general rule 10N of strength is
required per KG of force applied to
the motor.
RODEO
BOTTOM OPENING WINDOWS
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the height of the window.
• Follow the column down and select the desired opening amount.
• Below the opening, the required power rating from the motor is shown.
• Use the opening and the power required from the chart to select the
appropriate motor from the list below.
height of the window 500mm - 1000mm
desired opening (mm)
power required (N)
1000mm - 2000mm
0-200
0-200
450
450
2000mm - 2500mm
0-300
450
1000
0-300
450
1000
0-500
450
NOTE: Calculation of the power required is based on the most common systems on the market. For an exact calculation use the below formula.
W = width of the window
F = needed force in Kg
S = desired stroke in mm
F
H
S
G
W
H = height of the window in mm
G = weight of the window in Kg
F=
S
G
x
H
2
F x 10*
450N
1000N
RODEO DC
Motor
Designation
Rodeo DC 200mm
Rodeo DC 300mm
= Motor required
Rodeo DC 300mm
450N
1000N
RODEO AC
Motor
Designation
Rodeo DC 500mm
Torque -->
Rodeo AC 200mm
Rodeo AC 300mm
• The height (H) of the window must be at least
twice the size of the desired opening. Keep in
mind the maximum sag of the chain.
*As a general rule 10N of strength is required
per KG of force applied to the motor.
(Round up to the nearest N motor)
Torque -->
• The width (W) of the window must not exceed
1500mm and must be at minimum 500mm.
Rodeo AC 300mm
Rodeo AC 500mm
[ 121 ]
LINKEO
SKYLIGHTS
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the length of the skylight.
• Follow the column down and select the desired opening amount.
• Below the opening, the required power rating from the motor is shown.
• Use the opening and the power required from the chart to select the appropriate
motor from the list below.
length of the skylight
500mm - 1000mm
1000mm - 2000mm
Skylights are available in many types. The manner of rotation
can vary as well.
desired opening (mm)
200
250
250
420
A Velux type skylight in a horizontal roof that can be tilted
to 30˚ has a distributed weight of 50% at the hinges and 50%
at the motor.
power required (N)
200
200
200
400
On skylights that swivel, the weight is nil in the middle and the
power needed is determined only by the friction of the window.
NOTE: Calculation of the power required is based on the most common systems on the market. For an exact calculation use the below formula.
W = width of the skylight
F = needed force in Kg
Gsl G
L
S = desired stroke in mm
S
F
W
G = weight of the skylight in Kg
Gsl = snow load per m2†
F=
Fx
G + Gsl†
2
10* = Motor required
Torque -->
200N
400N
LINKEO DC
Motor
Designation
(Round up to the nearest N motor)
Linkeo DC 200mm
Linkeo DC 420mm
Torque -->
200N
400N
LINKEO AC
Motor
Designation
Linkeo DC 250mm
Linkeo AC 200mm
Linkeo AC 420mm
Linkeo AC 250mm
[ 122 ]
• The width (W) of the skylight must
not exceed 1500mm and must be at a
minimum 500mm.
• The length (L) of the skylight must be at
least twice the size of the desired opening.
Keep in mind the maximum sag of the
chain.
† If applicable.
* As a general rule 10N of strength is required
per KG of force applied to the motor.
RODEO
DOMES
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the desired opening amount.
• Below the opening, the required power rating from the motor will be shown.
• Use the opening and the power required from the chart to select the
appropriate motor from the list below.
desired opening (mm)
0 - 200
power required (N)
450
0 - 300
450
0 - 500
1000
450
NOTE: Calculation of the power required is based on the most common systems on the market. For an exact calculation use the below formula.
W = width of the dome
F = needed force in Kg
Gsl G
S = desired stroke in mm
S
F
G = weight of the dome in Kg
Gsl = snow load per m2†
W
L
G + Gsl†
F=
2
F x 10*
= Motor required
Torque -->
450N
1000N
RODEO DC
Motor
Designation
(Round up to the nearest N motor)
Rodeo DC 200mm
Rodeo DC 300mm
Rodeo DC 300mm
Torque -->
450N
1000N
RODEO AC
Motor
Designation
Rodeo DC 500mm
Rodeo AC 200mm
Rodeo AC 300mm
Rodeo AC 300mm
Rodeo AC 500mm
[ 123 ]
• The width (W) of the dome must not
exceed 1500mm and must be at
a minimum 500mm.
† If applicable.
* As a general rule 10N of strength is required
per KG of force applied to the motor.
RODEO
LOUVRES
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the desired opening amount.
• Below the opening, the required power rating from the motor will be shown.
• Use the opening and the power required from the chart to select the
appropriate motor from the list below.
desired opening (mm)
0 - 200
power required (N)
450
0 - 300
450
0 - 500
1000
450
NOTE: Theoretically louvres change little between systems. Friction/mechanics of a system are generally low and the blades are balance
therefore do not require much power to turn.
Torque -->
450N
1000N
RODEO AC
Motor
Designation
As a result the 450N motor is often suf cient to handle the friction in the system.
Rodeo DC 200mm
Rodeo DC 300mm
Rodeo DC 300mm
Torque -->
450N
1000N
RODEO DC
Motor
Designation
Rodeo DC 500mm
Rodeo DC 200mm
Rodeo DC 300mm
Rodeo DC 300mm
Rodeo DC 500mm
[ 124 ]
LINKEO 2
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz motor or 24V DC.
Natural ventilation is a breeze with the Linkeo 2 chain actuator range. Integrating a
powerful drive unit with a duplex chain in a compact design, the Linkeo 2 motor is the
perfect solution for window openings. When utilising Somfy control systems the Linkeo 2
motor can aid in expelling hot air and allow cool afternoon air to flow into a home,
office or any other installation via a timer, thermostat or at the touch of a button.
With low power consumption and available in either 230V AC or SELV (Safety Extra-Low
Voltage) 24V DC the range of possibilities with Somfy electronics is endless.
Electronic Factory set limits (can be connected in parallel).
4 minute running time.
Linkeo DC requires a regulated power supply.
Suitable for most glass window applications with no additional brackets required.
Maintenance Free.
Horizontal mount only.
Intermittent Usage.
24V DC
LINKEO 2 DC 200mm
LINKEO 2 DC 250mm
Torque (N)
200
Speed (mm/s)
10
Ref.
1230000
Torque (N)
200
Speed (mm/s)
10
Ref.
1230002
Torque (N)
200
Speed (mm/s)
10
Ref.
1230001
Torque (N)
200
Speed (mm/s)
10
Ref.
1230003
230V AC
LINKEO 2 AC 200mm
LINKEO 2 AC 250mm
NOTE: The Linkeo is not equipped with a safety cut-out.
Ensure a safety device is installed in installations that require it.
[ 125 ]
LINKEO 2
TECHNICAL CHARACTERISTICS
24V DC
230V AC
Blue = Positive or Negative
Blue = Neutral
Brown = Extend
Black = Retract
Brown = Negative or Positive
Stroke
Green/Yellow = Earth
LINKEO 2 AC 200mm
A (mm)
224
269
324
349
B (mm)
261.4
286.4
341
366
200
LINKEO 2 AC 250mm
LINKEO 2 DC 250mm
LINKEO 2 DC 200mm
B
Torque (Nm)
200
200
200
Speed (mm/s)
10
10
10
10
Stroke (mm)
200
250
200
250
Rated Voltage (V)
230AC
24DC
24DC
230AC
Rated Power consumption (W)
20
20
30
30
Rated Current (A)
0.8
0.8
0.13
0.13
Running time before thermal cut off (min)
4
4
4
4
Motor weight (kg)
1.1
1.1
1.1
1.1
1.5
Cable length (M)
1.5
1.5
1.5
Number of cores in cable
2
2
4
4
Cross section of cable (mm²)
1.0
1.0
1.0
1.0
Index Protection
IP20
IP20
IP20
IP20
Normal functioning temperature: -10°C to +40°C
[ 126 ]
LINKEO 4
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz motor or 24V DC.
Natural ventilation is a breeze with the Linkeo 4 chain actuator range. Integrating a powerful
drive unit with a duplex chain in a compact design, the Linkeo 4 motor is the perfect solution for
window openings. When utilising Somfy control systems the Linkeo 4 motor can aid in expelling
hot air and allow cool afternoon air to flow into a home, office or any other installation via a
timer, thermostat or at the touch of a button. With low power consumption and available in
either 230V AC or SELV (Safety Extra-Low Voltage) 24V DC the range of possibilities with Somfy
electronics are endless.
Electronic Factory set limits (can be connected in parallel).
4 minute running time.
Linkeo DC requires a regulated power supply.
Suitable for most glass window applications with no additional brackets required.
Maintenance Free.
Horizontal mount only.
Intermittent Usage.
24V DC
LINKEO 4 DC 420mm
LINKEO 4 DC 600mm
LINKEO 4 DC 835mm
Torque (N)
400
Speed (mm/s)
17
Ref.
1230005
Torque (N)
400
Speed (mm/s)
17
Ref.
1230006
Torque (N)
400
Speed (mm/s)
17
Ref.
1230004
Torque (N)
400
Speed (mm/s)
22
Ref.
1230007
Torque (N)
400
Speed (mm/s)
22
Ref.
1230008
230V AC
LINKEO 4 AC 420mm
LINKEO 4 AC 600mm
NOTE: The Linkeo is not equipped with a safety cut-out.
Ensure a safety device is installed in installations that require it.
[ 127 ]
LINKEO 4
TECHNICAL CHARACTERISTICS
24V DC
230V AC
Blue = Positive or Negative
Blue = Neutral
Brown = Extend
Black = Retract
Brown = Negative or Positive
LINKEO 4 DC 420mm
LINKEO 4 DC 600mm
LINKEO 4 DC 835mm
LINKEO 4 AC 420mm
LINKEO 4 AC 600mm
Stroke
Green/Yellow = Earth
A (mm)
458
553
667
458
553
B (mm)
478
573
687
478
573
C (mm)
514
609
723
514
609
400
Torque (Nm)
400
400
400*
400
Speed (mm/s)
17
17
17
22
22
Stroke (mm)
420
600
835
420
600
Rated Voltage (V)
24DC
24DC
24DC
230AC
230AC
50
50
50
160
160
2.08
2.08
2.08
0.69
0.69
Rated Power consumption (W)
Rated Current (A)
Running time before thermal cut off (min)
4
4
4
4
4
Motor weight (kg)
3.4
3.8
4.3
3.4
3.8
1.5
Cable length (M)
1.5
1.5
1.5
1.5
Number of cores in cable
2
2
2
4
4
Cross section of cable (mm²)
1.0
1.0
1.0
1.0
1.0
Index Protection
IP22
IP22
IP22
IP22
IP22
Normal functioning temperature: -10°C to +40°C
* Rated at: 200N thrust/push
400N Tensile/pull
[ 128 ]
RODEO
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz motor or 24V DC.
Glare control and ventilation can be easily managed with the help of the
Rodeo linear motor. With a powerful rod drive unit and a IP55 housing, the Rodeo
motor is the perfect solution for window openings, louvre panels and skylights.
When utilising Somfy control systems the Rodeo motor can aid in expelling hot air and
allow cool afternoon air to flow into a home, office or any other installation via a timer,
thermostat or at the touch of a button. If glare control is required when utilised on a
louvre system the Rodeo can accurately tilt the blades to the required position.
With low power consumption and available in either 230V AC or SELV (Safety Extra-Low
Voltage) 24V DC the range of possibilities with Somfy electronics is endless.
Adjustable stroke with electronic shut off (can be connected in parallel).
4 minute running time.
Suitable for most applications with no additional brackets required.
Maintenance Free.
Intermittent Usage.
24V DC
RODEO
RODEO
RODEO
RODEO
DC 450N 200mm
DC 450N 300mm
DC 450N 500mm
DC 1000N 300mm
Torque (N)
450
Speed (mm/s)
8
Ref.
1230010
Torque (N)
450
Speed (mm/s)
8
Ref.
1230012
Torque (N)
450
Speed (mm/s)
8
Ref.
Torque (N)
1000
Speed (mm/s)
3
Ref.
1230014
1230016
Torque (N)
450
Speed (mm/s)
8
Ref.
1230009
Torque (N)
450
Speed (mm/s)
8
Ref.
1230011
Torque (N)
450
Speed (mm/s)
8
Ref.
Torque (N)
1000
Speed (mm/s)
3
Ref.
1230013
1230015
230V AC
RODEO AC 450N 200mm
RODEO AC 450N 300mm
RODEO AC 450N 500mm
RODEO AC 1000N 300mm
NOTE: Requires the use of a safety device when utilised in an installation where
jamming may occur. Unit is not equipped with a safety cut-out.
[ 129 ]
RODEO
TECHNICAL CHARACTERISTICS
24V DC
230V AC
Blue = Positive or Negative
Blue = Neutral
Brown = Extend
Black = Retract
Brown = Negative or Positive
Green/Yellow = Earth
RODEO AC 1000N 300mm
RODEO AC 450N 500mm
RODEO AC 450N 300mm
RODEO AC 450N 200mm
RODEO DC 1000N 300mm
RODEO DC 450N 500mm
RODEO DC 450N 300mm
RODEO DC 450N 200mm
Stroke
A (mm)
330
430
630
430
330
430
630
430
B (mm)
200
300
500
300
200
300
500
300
408
C (mm)
308
408
608
408
308
408
608
D (mm)
234
334
535
334
234
334
535
334
Torque (Nm)
450
450
450
1000
450
450
450
1000
Speed (mm/s)
8
8
8
3
8
8
8
3
Stroke (mm)
200
300
500
300
200
300
500
300
Rated Voltage (V)
24DC
24DC
24DC
24DC
230AC
230AC
230AC
230AC
22
22
22
18
30
30
30
23
0.91
0.91
0.91
0.75
0.13
0.13
0.13
0.1
Rated Power consumption (W)
Rated Current (A)
4
4
4
4
4
4
4
4
Motor weight (kg)
1.19
1.40
1.40
1.73
1.19
1.40
1.40
1.73
1.5
Running time before thermal cut off (min)
Cable length (M)
1.5
1.5
1.5
1.5
1.5
1.5
1.5
Number of cores in cable
2
2
2
2
4
4
4
4
Cross section of cable (mm²)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
Index Protection
IP55
IP55
IP55
IP55
IP55
IP55
IP55
IP55
Normal functioning temperature: -10°C to +40°C
[ 130 ]
MOTOR BRACKETS
LINKEO,
RODEO
LINKEO 2 TOP BRACKET
R O D E O R O D B R ACK E T
Mounting suitable
for a top hung
window with or
without a sill.
Multi-fit rod bracket for
windows, skylights, louvre
panels, etc.
Use: Rodeo
Use: Linkeo 2
Ref. INCLUDED WITH MOTOR
Ref. INCLUDED WITH MOTOR
L I N K E O 2 B OTTO M B R AC K E T
RODEO MOTOR BRACKET
Mounting
suitable for a
bottom hung
window.
Multi-fit motor bracket for
windows, skylights, louvre
panels, etc.
Use: Rodeo
Use: Linkeo 2
Ref. INCLUDED WITH MOTOR
Ref. INCLUDED WITH MOTOR
L I N K E O 4 TOP B RACK E T
Mounting suitable
for a top hung
window with
or without a sill.
Use: Linkeo 4
Ref. INCLUDED WITH MOTOR
L I N K E O 4 B OTTO M B R ACK E T
Mounting
suitable for a
bottom hung
window.
Use: Linkeo 4
Ref. INCLUDED WITH MOTOR
[ 131 ]
ILT MOTORS
MOTORS,CONTROLS & ACCESSORIES
ILT2 Motors ....................................................... 133
Sonesse 50 ILT2 .................................................. 135
Controls ........................................................... 137
Accessories ....................................................... 138
ILT2 MOTORS
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor.
The ILT (Intelligent Limit Technology) motor has been specifically designed to
provide a modular control system. Available in torques from 6Nm to 35Nm, with a
flexible 48mm design, it is adapted for Ø50mm tubes and above. Utilising a 230V
powered connection with a telephone wire connection for control, modules can
be clipped onto the data wire to enable a plethora of control setups. The ILT motor
can become IR (Infrared) compatible with just a single simple plug in, RTS (Radio
Technology Somfy) with the addition of a receiver or wired control just as easily.
Using a specific plug in tool for limit setting/ adjustment the
great integrated control solution. Allows an illimited number of intermediate positions
Tool operated limit setting.
300 turn limit capacity.
Suitable for tubes: Ø50 to Ø65.
Volt free switch control via flat four core telephone data cable.
Requires the use of a crown and wheel for tube adaptation.
Horizontal mount only.
Intermittent Usage.
ILT2
ITL2
ITL2
ITL2
ITL2
ARIANE 6/17 VVF 3M UNIT
ATLAS 15/17 VVF 3M UNIT
APOLLO 35/17 VVF 3M UNIT
ARIANE 6/32 VVF 3M UNIT
ATLAS 15/32 VVF 3M UNIT
Torque (Nm)
6
Speed (RPM)
17
Ref.
1100031
Torque (Nm)
15
Speed (RPM)
17
Ref.
1100032
Torque (Nm)
35
Speed (RPM)
17
Ref.
1100033
Torque (Nm)
6
Speed (RPD)
32
Ref.
1100034
Torque (Nm)
15
Speed (RPD)
35
Ref.
1100035
[ 133 ]
ILT2 Range 1
230 V - 50 Hz
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active
Yellow /Green = Earth
Red = Up
Blue = Common
White = 5v
Yellow = Down
L1
L2
Data Cable
ILT2 Apollo 35/17
605
613
613
6
32
0,5
120
1,85
52
ILT2 Atlas 15/32
605
590
613
6
17
0,4
90
1,72
46
ILT2 Atlas 15/17
ILT2 Ariane 6/32
L1 (mm)
L2 (mm)
L3 (mm)
Torque (Nm)
Speed (rpm)
Max. Current consumption (A)
Power (W)
Motor Weight (Kg)
Power Level (dBa)
Voltage
Voltage Frequency
Protection Index
Head
Power Cable
ILT2 Ariane 6/17
3.95
Ø 47
50mm
605
705
705
613
690
690
613
713
713
15
15
35
17
32
17
0,65
1,1
1,1
140
240
240
1,95
2,55
2,55
50
56
56
230V
50Hz
IP44
Star
Included / 3m / 3 Wires
Included / 2.5m / 4wires / RJ9 phone
connectors
[ 134 ]
17.15
min
25
20
Ø 63
Sonesse 50 ILT2
MAIN CHARACTERISTICS & FEATURES
230V / 50Hz tubular motor
The Sonesse 50 has been adapted to be a quiet roller blind motor. Available in 3Nm, coupled
with its flexible 48mm design, it is adapted for 50mm tubes and above.
Utilising a 230V powered connection with a telephone wire connection for control, modules
can be clipped onto the data wire to enable a plethora of control setups. The Sonesse 50 ILT2
motor can become IR (infrared) compatible with just a single simple plug in, RTS (Radio
Technology Somfy) with the addition of a receiver or wired control just as easily. Using a
specific plug in tool for limit setting/ adjustement the ILT motor makes a great integrated
control solution.
Tool operated limit setting
300 turn limit capacity
Requires the use of a crown and wheel for tube adaptation
Horizontal mount only
Intermittent Usage.
SONESSE 50 ILT2 3/28 VVF 3M UNIT
Torque (Nm)
SONESSE 50 ILT2 3/28 VVF 3M UNIT
SONESSE 50 ILT2 3/28 VVF 3M BAR
Torque (Nm) 3
Torque (Nm) 3
[ 135 ]
3
Speed (RPM)
28
Speed (RPM) 28
Speed (RPM) 28
Ref.
1030051
Ref. 1030051
Ref. 1100052
Sonesse 50 ILT2
TECHNICAL CHARACTERISTICS
Blue = Neutral
Brown = Active 1
Black = Active 2
Green/Yellow = Earth
L1
L2
Soonesse 50 ILT2
3.95
Ø 47
24
L1 (mm)
783
L2 (mm)
770
L3 (mm)
796
Torque (Nm)
3
Speed (rpm)
28
Max. Current consumption (A)
0.4
Power (W)
90
Motor Weight (Kg)
2.875
Power Level (dBa)
ื 44
Voltage
230V
Voltage Frequency
50Hz
Protection Index
IP31
Head
Star
Power Cable
Included / 3m / 3 Wires
Included / 2.5m / 4wires
Data Cable
RJ9 phone connectors
[ 136 ]
25
17.15
min
20
Ø 63
Ø 74
CONTROLS
Screw Terminal/Phone Plug Interface
ILT General Control Devices
Controller board for connecting
indivisual and/or master control
of ILT motors
Controller board for interfacing a dry
contact switch to an ILT motor
4 RJ9 female phone connector or
ILT motors and switches
2 x RJ9 female phone connector for 2 ILT
motors (or one motor and one IR3 sensor)
Dimensions (with plastic casing) :
43x48mm
Dimensions (with plastic casing) :
43x48 mm
Ref. 9050200
Ref. 1860014
Multiple Phone Connector
Controller board for connecting
multiple ILT motors or switches together
4 x RJ 9 female phone connector for ILT
motors, IR3 sensors or switches
Dimensions ( with plastic casing ) :
43x48mm
Ref. 9050190
RS 485 4ILT Interface
Lon Biu-2ILT Motor Controller Device
Manage upto 4 Roller Blinds /
projection screens
Manage upto 2 Blinds
Compatible with ILT2 motors
Controlled by Lonworks network, 2x Local
Double push-buttons, 2 x 6
contact switches (RJ 11)
Compatible with ILT and ILT2 motors
Controlled by IR, RS485 Somfy
Commands or Trigger
Powered by the network
Upto 8 favourites formats
Installation with software, which includes Node,
Group control, Sun and Wind functions
Universal Power supply : 90-255V
Ref. 1860016
Ref. 1870130
KNX/EIB interface 510I
Manage 1 Blinds
Compatible with ILT and ILT2 motors
Controlled by EID Bus
Bi- Directional data exchange
Power supply : 24 VDC
Ref. 1860021
IR 1
IR 8
Single channel infrared remote control
8 channel infrared remote control
Compatible with IR3 Sensor 7M range
Compatible with IR3 Sensor 7M range
2 x AAA Battery (Included)
2 x AAA Battery (Included)
Ref. 1870132
Ref. 1870133
[ 137 ]
Accessories
IR 3 ILT Sensor
New ILT setting Tool
Infrared sensor IR 3
Color : White
Elecronic tool to program end-limits
and rotation direction of ILT1 and ILT2
motors
Compatible with :
- IR1 and IR8 Somfy remote control
- Universal Ir Remote
Motor’s connection: RJ19 female connector
Included :
- ILT phone cable (2.5m)
- Fixing screw
Ref. 9154186
Ref. 9050280
ILT Phone Cable
Roll of Phone Cable
Lenght 0.3m
Roll of flat phone cable,
for data communication with ILT motors
Four wires flat phone cable, for data
communication with ILT motors
Ref. 9209062
Lenght 1.5m
Ref. 9209061
Lenght : 100 meters
RJ9 Phone connectors
Color : White
Color : White
Lenght 2.5m
Ref. 9209062
Lenght 3m
Ref. 9209063
Ref. 9686031
[ 138]
Commercial Building
Solutions
Animeo Solo .................................................... 140
Animeo Solo Solution Examples ............................. 142
Animeo Solo Accessories ...................................... 144
Animeo IB+ Compact ........................................... 147
Animeo IB+ Compact Solution Examples .................. 149
Animeo IB+ Compact Building Controller, Operating Interface .......... 151
Animeo IB+ Compact Software, animeo IB+ Compact Sensor, Sensor Boxes ....... 152
Animeo IB+ Compact accessories ........................... 153
Animeo IB+ Premium ......................................... 155
Animeo IB+ Premium solution examples .................. 157
Animeo IB+ Specification Software “Quick-Quote” ..... 159
Animeo IB+ Building Controller ............................. 160
Animeo IB+ Premium OPC Software ................................ 161
Animeo IB+ Premium Accessories .......................... 162
Animeo IB+ Motor Controller ................................ 165
1 AC Motor Controller, 4 AC Motor Controller .............. 166
4 DC Motor Controller, 4 DC / DC-E Motor Controller, animeo IB+ DALI interface ........... 167
Animeo IB+ Accessories ....................................... 168
animeo solo
The starting point of the range. An easy
to use system. animeo Solo is a new
centralized opening and sun protection
device management system that brings
the benefits of bioclimatic façades to
small commercial buildings. The
building´s façade reacts in real time to
climate variations, providing greater
control over air, lighting, sunlight and
shade. The building´s occupants enjoy a
greater level of comfort.
Outside
2x
2x
sun & wind
or
or
sun
animeo Solo
2 zones
animeo Solo
1 zone
1 x Controlling
Technology (IB or IB+)
Motor
Controller
devices
Motor Controller devices:
To control motors and connection to e. g. local push
buttons
2 x Controlling
Technology (IB or IB+)
IB
IB+
M
M
M
animeo IB+
1 AC Motor
Controller
WM
Centralis Uno IB VB
animeo IB+
1 AC Controller
Circuit board
[ 140 ]
M
M
M
animeo
Motor
Controller
AC, DC, DC-E
(wall-mounted)
animeo 4 AC Motor
Controller (DIN-rail mounted)
animeo Solo
contributes to
the development of
bioclimatic façades.
animeo solo
Product advantages
Important for site managers
• Can control up to two zones (façade orientations).
• With its LCD configuration screen, animeo Solo is simple
and intuitive to install.
• The system comes with a basic configuration, and the user
can use the screen-based interface to program the system
and view the weather settings in real time.
• Automatic cold protection and natural heating function
implemented.
• Compatible with all Motor Controller devices from the
Somfy Controlling technology: animeo IB+, IB-Inteo, CD.
For maximum functionality we recommend animeo IB+
Motor Controller devices.
• Very suitable for users without experience in
controlling sun protection devices.
• The building manager can control (up-down-stop) each
zone separately or lock zones for maintenance operations.
• The built-in multi language backlit graphical LCD helps to
easy navigate and make any setting.
Manage 1 or 2 separate zones
Further features
• Very suitable for users without experience in
controlling sun protection devices.
• Operates 400 to 800 AC, DC or DCE (Encoder) motors.
• Precise setting of running and tilting times depending on
the selected end product to be controlled.
• Sun function with settable threshold values, delays,
positions and degree of angle, per zone.
• Wind security function with settable threshold values and
sensor assigning, per zone.
• Rain and frost security function with settable threshold
value and delay times, per zone.
• The LCD continuously presents the systems status and
weather data such as wind speed, rain, sun radiation and
temperature.
• Daily timer per zone with one settable time zone per day
to configure and positioning command.
• Potential free main alarm input.
• Choice of 14 different languages in the display.
· Easy functional extendability of an animeo Solo system to
an animeo IB+ Compact system by changing the Building
Controller and with sensors.
· In combination with the animeo IB+ Motor Controller
devices: 230 V AC, 24 V DC, 24 V DC/E motors can be
controlled.
[ 141 ]
Solution example 1
Desired functionality
Automatic functions
One zone (west) should be controlled. The façade is fitted
with exterior Venetian blinds. For the user the solution must
be simple and intuitive to install. For the user interface, an
easy to operate display is desired. Manual local control of
the motors is also requested to allow the user to choose his
preferred position. Installation-wise; individual sensors are
requested to be installed on the façade.
1. Wind security
2. Sun automatic
The solution
+
+
animeo Solo 1 zone
1 860 143
Page 46
Wind Sensor
9 001 608
Page 46
+
Sun Sensor
9 154 217
Page 46
+
animeo
Motor Controller device
1 860 049
Page 70
Push button
Centralis IB
1 810 138
Page 48
Solution in building
M
Motors
M
M
M
W
N
S
O
Building orientation
Engineering room
[ 142 ]
Solution example 2
Desired functionality
Automatic functions
Up to two separate zones (west and east) to be controlled.
One façade is fitted with exterior Venetian blinds, the other
with external screens. For the user the solution must be simple and intuitive to install. For the user interface, an easy to
operate display is desired. Radio control of the motors is also
requested for excellent user comfort. Installation-wise;
a complete integrated sensor unit is preferable.
1. Wind security per zone
2. Sun automatic per zone
3. Rain and frost security
4. Daily timer per zone
The solution
+
animeo Solo
2 zones
1 860 144
Page 46
+
Soliris Sensor
9 154 080
Page 46
+
Rain Sensor
9 705 588
Page 47
+
Outside
temperature
Sensor
9 001 611
Page 47
+
animeo Motor
Controller device
4 outputs
1 860 049
Page 70
+
RTS radio module
room control
device
1 860 105
Page 72
Telis 4
Modulis
RTS Lounge
1 810 664
Page 72
Solution in building
M
Motors
M
M
M
W
N
S
O
Building orientation
M
Motors
M
M
M
[ 143 ]
Engineering room
animeo Solo accessories
animeo Solo Building Controller
Central Control unit of the
animeo Solo system
Product advantages
• Controlling up to 2 zones /
façades.
• AC, DC or DC-E motor systems
can be controlled (one type per
zone).
Further features
• For each zone, up to 100 Motor
Controller devices can be connected.
• Compatible with all Motor Controller devices from the Somfy
Controlling technology: animeo
IB+, IB-Inteo, CD.
On zone / façade level
• Precise setting of running and
tilting times depending on the
Eolis Sensor
Wind sensor (without integrated
sun sensor).
selected end product to be
controlled.
• Sun function with settable
threshold values, delays, positions and degree of angle.
• Wind security function with
settable threshold values and
sensor assigning.
• Rain and frost security function
with settable threshold value
and delay times.
• Outside temperature function
with settable threshold value
and delay times.
• Direct connection of 1 or 2
independent zone switches for
maintenance purposes.
Further features
• Measurement of wind speed
and sun intensity combined in
one housing.
• Comfortable threshold setting
on the device.
Measurements (W x H x D):
Degree of protection:
Protection class:
Wiring recommendations:
Eolis Sensor
Wind Sensor (not heated)
225 × 148 × 48 mm
IP 20
II
230 V AC
0 °C to +45 °C
animeo Solo 1 zone
animeo Solo 2 zone
9 101 479
.
On building level
• Timer with 2 setting times
per day to configure an UP or
DOWN command (incl. blocking).
• An input for the main alarm,
potential free contact. When
the input is active all end
product will be blocked at the
UP position.
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
160 × 236 × 40 mm
IP 33
II
2 × 2 × 0,8 mm
Measurements:
1 860 143
1 860 144
Degree of protection:
Wiring recommendations:
Height 200 mm, ø 240 mm
max. ø-mast: 48 mm
IP 65
2 × 1,5 mm
Wind Sensor (not heated)
9 001 608
.
For wall mounted installation, 12 SUs.
.
Sun Sensor
Soliris Sensor
Combined weather station
Further features
• Measurement of wind speed
and sun intensity combined in
one housing.
• Comfortable threshold setting
on the device.
Measurements (W x H x D):
Degree of protection:
Protection class:
Wiring recommendations:
Measurements Sun Sensor (W x H x D):
Degree of protection:
Wiring recommendations:
Angel position:
160 × 236 × 40 mm
IP 43
II
2 × 2 × 0,8 mm
Soliris Sensor
34 × 88 × 47 mm
IP 43
2 × 0,8 mm
150 °
Sun Sensor without mounting bracket
Mounting bracket for sun sensor
9 154 217
9 127 888
.
9 154 080
.
[ 144 ]
animeo Solo accessories
Outside Temperature Sensor
Aquatic Rain Sensor
With solar radiation sensor
shelter.
Measurements:
Degree of protection:
Wiring recommendations:
Rain Sensor including power
supply. Potential free output
with change-over contact.
Height 150 mm, ø 115 mm
IP 65
2 × 0,8 mm
Outside Temperature Sensor
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Wiring recommendations:
Environment temperature:
9 001 611
.
70 × 100 × 130 mm
IP 65
III
24 V DC
2 × 2 × 0,8 mm
-25 °C to +50 °C
Aquatic Rain Sensor
9 011 235
Rain Sensor (230 V)
.
With thermostatically regulated
heater, potentially free output.
Room Thermostat
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Wiring recommendations:
70 × 185 × 30 mm
IP 65
I
230 V AC
2 × 2 × 0,8 mm
Rain Sensor (230 V)
Measurements (W x H x D):
Degree of protection:
Protection class:
Wiring recommendations:
9 705 588
.
75 × 75 × 25 mm
IP 20
III
2 × 2 × 0,8 mm
Room Thermostat
9 709 808
Rain Sensor
.
With direct 24 V supply over the
Outside Sensor Box.
Inside Temperature Sensor
With 1 m cable.
Measurements (W x H x D):
Degree of protection:
Wiring recommendations:
50 × 90 × 40 mm
IP 65
3 × 1,5 mm
Rain Sensor
9 001 610
Inside Temperature Sensor
.
[ 145 ]
9 008 044
animeo Solo accessories
Housing for Inside Temperature Sensor
Measurements (W x H x D):
75 × 75 × 25 mm
Housing for Inside Temperature Sensor
9 008 045
Push button Centralis IB
Manual controlling of several
motors over IB-Bus. Comfortable Central Control or group
operability. Operation via the big
UP, DOWN and STOP buttons is
possible at any time.
Centralis IB
1 810 138
Delivery incl.: Switch, inteo cover plate, inteo cover plate frame and
claws.
Centralis IB
1 800 278
Delivery incl.: Switch and matching cover (see selection in appendix
but without cover plate).
[ 146 ]
animeo ib+ compact
buildings. The animeo IB+ Compact
enables the cost-effective control of
sun protection systems and is easy to
This sun protection system completes
the animeo product range with special
solutions that are optimised for small
1x
3x
4x
2x
DCF
DCF
install and configure. The system can be
configured with or without a PC.
4x
Outside
Inside
Outside
Sensor Box
Inside
Sensor Box
OPTIONAL
OR
Compact Sensor
A compact
but complete
weather station
Operating interface or Compact PC software: The animeo Operating
Interface provides an intuitively designed, guided user interface for
configuring the control systems of sun protection systems.
Operating
Interface
OR
The Compact Building Controller
is the central control unit of the
animeo IB+ Compact system.
Compact Building Controller
for 4 zones
Central control
PC
4 x control cables (IB or IB+)
Motor
Controller
devices
Motor Controller devices:
To control motors and connection to e. g. local push
buttons
IB
IB+
M
M
M
animeo IB+
1 AC Motor
Controller
WM
Centralis Uno IB VB
M
M
M
animeo
Motor
Controller
AC, DC, DC-E
(wallmounted)
animeo IB+
1 AC Controller
Circuit board
animeo 4 AC Motor
Controller (DIN-rail mounted)
[ 147 ]
animeo ib+ compact
animeo IB+Compact
contributes to
the development of
bioclimatic façades.
· Easy functional extendability of an animeo IB+ Compact
system to an animeo IB+ Premium system by changing the
Building Controller and eventually also the Compact
sensor.
· In combination with the animeo IB+ Motor Controller devices: 230 V AC, 24 V DC, 24 V DC/E motors can be
controlled.
Product advantages
· Can control up to four zones (façade orientations).
· Free selecting of the user Interface: PC software or Operating Interface interchangeable at any time.
· Advanced operating mode: higher room-suited user comfort through supress of non-security functions (e. g. sun)
as soon as local operation has been assigned. The system
switches again to automatic at a pre-defined time.
· Compatible with all Motor Controller devices from the
Somfy Controlling technology: animeo IB+, IB-Inteo, CD.
For maximum functionality we recommend animeo IB+
Motor Controller devices.
Important for site managers
· Easy and favourably-priced and high performance.
· PC user interface or display. The PC user software is available at no extra cost.
· Greater user comfort in combination with animeo IB+
Motor Controller devices (see “advanced operating mode”
under “product advantages”).
Further features
· Suitable for users with or without experience in controlling
sun protection systems.
· Extendable up to 1600 motors.
· Building Controller and user interface can be installed
separately, user interface e. g. in the caretaker/facility
manager’s room.
· Through the application of the Compact Sensor, wiring is
made very easy as all sensors are integrated in the sensor.
· Communication between Compact Sensor/Outside Sensor
Box and Building Controller is monitored.
· Selection of functions and parameters are designed especially for the type of end product to be controlled, e. g.
Venetian blinds, blinds, roller shutters.
· Sun function with settable threshold values, delays, position, degree of angle, per zone.
· Wind security function with settable threshold values, sensor assigning, all per zone.
· Rain and ice security function with settable temperature
threshold value, delay times, all per zone.
· Central timer with two settable time zones per day to configure an on/off command with blocking.
· Potential free main alarm input with configurable action
per zone: up or down command with blocking.
· DCF-77 (radio controlled clock, Frankfurt) time synchronisation (standard in Compact Sensor, optional with Outside
Sensor Box).
· Password protection of the settings.
· Potential free error output, e. g. in the event of sensor
failure.
OR
[ 148 ]
Solution example 1
Automatic functions
A “small” project with a compact central control unit, PC
interface, and Motor Controllers in the flush-mounted box.
Desired functionality
Up to three separate façade zones (for example, east, south,
and west) need controlling. The façades are fitted with external Venetian blinds (AC motors). An easy-to-use PC software
is required as the operating interface. A completely integrated sensor unit is preferred for the installation.
1. Wind protection
2. Automatic sun protection
3. The automatic sun protection function can be deactivated
for the room by the room user by means of a sliding switch
integrated into the control point.
The solution
+
Compact Building Controller
1 822 189
Page 54
+
Compact Software
9 013 433
Page 55
+
Compact Sensor
9 015 047
Page 55
+
Compact
Power Supply
1 860 118
Page 56
Centralis Uno IB
1 810 282
Page 127
Solution in building
M
Motors
M
M
M
W
N
S
O
Building orientation
M
Motors
M
M
M
[ 149 ]
Engineering room
Solution example 2
A “small” project with a compact central control unit,
PC interface, and Motor Controllers in the flushmounted box.
Desired functionality
Up to three separate façade areas (for example, east,
south and west) need controlling. The façades are
fitted with external Venetian blinds (AC motors). An
easy-to-use screen is required as the operating interface. A completely integrated sensor unit is preferred
for the installation.
Automatic functions
1. Wind protection
2. Automatic sun protection
3. The room user can use the local control unit to
deactivate the automatic sun protection function
for the room for the rest of the day. animeo Motor
Controllers are required for this function.
The solution
+
+
Compact Building Controller
1 822 189
Page 54
Operating
Interface /
Display
9 013 219
Page 54
+
Compact Sensor
9 015 047
Page 55
+
Compact
Power Supply
1 860 118
Page 56
+
animeo motor
controller device
4 outputs
1 860 049
Page 70
Push button
Centralis IB
1 810 138
Page 48
Solution in building
M
Motors
M
M
M
W
N
S
O
Building orientation
M
Motors
M
M
M
[ 150 ]
Engineering room
animeo IB+ Compact
animeo IB+ Compact Building Controller
Central Control unit of the
animeo IB+ Compact system
Product advantages
• Controlling of up to
4 zones / façades.
· AC, DC or DC-E motor systems
can be controlled (one type per
zone).
Further features
• For each zone, up to 100 Motor
Controller devices can be connected.
· Compatible with IB-Inteo or
CD-IB-Motor Controller devices.
On zone / façade level
· A wide selection of functions
and standard parameters designed especially for the type
of end product to be controlled, e. g. Venetian blinds,
blinds, roller shutters etc.
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
animeo IB+ Operating Interface / Display
· Sun function with settable
threshold values, delays, position, angle positioning with
Venetian blinds, assigning of
sensors.
· Wind safety function with settable threshold values, delays,
and assigning of sensors.
· Rain / ice safety function with
settable delay times.
For the operating and configuration of the animeo Compact System. Display of current weather
and system data.
On building level
· Timer with 2 setting times
per day to configure an UP or
DOWN command (incl. blocking).
· An input for the main alarm,
potential free contact, with
configurable action per control
zone / façade: UP or DOWN
command.
· DCF reception via Compact Sensor or animeo Outside Sensor
Box.
· Operating mode selection:
standard or advanced.
· Password protection of the
settings.
· An error output, potential free
open contact to signal e. g.
sensor dropout.
Product advantages
· Intuitively designed and
comprehensive user display;
suitable for users without or
with only a little experience
in controlling sun protection
systems.
· Integrated wiring test facilitates easier planning and
start-up.
· The Operating Interface is
operable independent of the
location of the installed Building Controller.
Measurements (W x H x D):
Safety type:
Protection class:
Operating voltage:
Environment temperature:
210 × 90 × 61 mm
IP 20
II
230 V AC
0 °C to +45 °C
Compact Building Controller
Operating Interface
For wall mounted installation.
1 822 189
For DIN-rail installation, 12 SUs.
Kit animeo Compact Building Controller + Interface
1 822 195
Delivery incl.: Building Controller, Compact Sensor + Power Supply,
Operating Interface.
Kit animeo Compact Building Controller + Interface
1 822 203
Delivery incl.: Building Controller, Compact Sensor + Power Supply,
software, USB RS485 interface.
[ 151 ]
Further features
· 128 x 64 pixel display with
background lighting.
· Password protection for settings.
· Assigned configurations can
also be called up by the animeo Compact PC software and
modified.
· The Operating Interface can
be removed after a successful
configuration.
· Communication with animeo
Compact Building Controller
over RS485 interface.
· Manual blocking of zones is
possible (window cleaning
function).
· Operation of blinds according
to façades or zones.
130 × 182 × 98 mm
IP 20
II
230 V AC
0 °C to +45 °C
9 013 219
animeo IB+ Compact
animeo IB+ Compact Software and
USB Interface
Interface between the Building
Controller and the PC including configuration and operating
software.
Product advantages
· User-friendly display design:
large, high, good resolution,
multi-coloured.
· Intuitively designed and
comprehensive user display;
suitable for users without or
with only a little experience
in controlling sun protection
systems.
· Integrated wiring test facilitates easier planning and
start-up.
· The Operating Interface is
operable independent of the
location of the installed Building Controller.
Outside Sensor Box
Further features
· Assigned configurations can
also be called up and modified
by the animeo Compact Operating Interface.
· Communication with animeo
Compact Building Controller
over RS485 interface.
· Manual blocking of zones is
possible (window cleaning
function).
· For computers with minimum
Intel Pentium II, 500 MHz,
Windows 2000, CD Rom disc
drive, 128 MB storage and 40
MB free hard drive storage.
· Operation of blinds according
to façades or zones.
Product advantages
· Only two cables (power supply
24 VAC / DC and data cable) must
be laid to the outside.
· Convenient lightning protection
possible as only two cables are
laid to the outside.
The Outside Sensor Box is the
interface between the weather
station and the Building Controller. All measurement values
are evaluated here and sent
to the Building Controller. It
requires an external 24 V AC / DC
power supply.
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
Outside Sensor Box
Further features
· All sensors incl. Outside Sensor
Box can be fixed to the sensor
station mast.
· Up to eight sun sensors, two
wind sensors, a rain sensor, an
outside temperature sensor as
well as a DCF plug module can
be connected to the Outside
Sensor Box.
207 × 255 × 90 mm
IP 65
III
24 V DC
-30 °C to +70 °C
9 001 606
For wall mounted installation.
animeo IB+ Compact Software and USB Interface
9 013 433
Inside Sensor Box
animeo IB+ Compact Sensor
The complete weather station
in a small format. 3 x sun, 1 x
wind, 1 x outside temperature,
1 x rain, DCF receiver. Additional
requirements: 24 VDC power
supply.
Product advantages
· Wiring made easy as all sensors
are integrated in the device.
· Monitored communication between Building Controller and
Compact Sensor.
To connect external push buttons or key switches per zone.
Further features
Integrated sensors:
· Three sun sensors in fixed
direction 90 ° (east), 180 °
(south) and 270 ° (west).
· Wind speed sensor without
moving parts.
· Outside temperature sensor.
· Heated rain sensor.
· DCF receiver for time synchronisation.
· Bracket for wall or post
mounting.
Product advantages
· Window cleaners need no
access to the complete user
interface (display or PC interface).
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
Inside Sensor Box
For DIN-rail installation, 12 SUs.
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
96 × 77 × 118 mm
IP 65
III
24 V DC ± 10 %
-25 °C to +50 °C
animeo IB+ Compact Senor
9 015 047
[ 152 ]
210 × 90 × 61 mm
IP 20
II
230 V AC
0 °C to +45 °C
9 001 614
animeo IB+ Compact accessories
animeo Power Supply DC
animeo IB+ Compact Power Supply
To supply the Outside Sensor Box
(without heated sensors).
To supply the animeo Compact
Sensor and the Outside Sensor
Box (without heated sensors).
Measurements (W x H x D):
130 × 180 × 61 mm
Degree of protection:
IP 20
Protection class:
II
Operating voltage:
230 V AC
Output current:
2,5 A (switch on duration 100 %)
4,5 A (switch on duration 50 %: 3 mins on, 3 mins off)
animeo Power Supply DC
Measurements (W x H x D):
Safety type:
Protection class:
Operating voltage:
Output voltage:
Output current:
1 860 093
57 × 91 × 57 mm
IP 20
II
230 V AC
24 V DC
350 m A
For wall mounted and DIN-rail installation.
animeo IB+ Compact Power Supply
1 860 118
For wall mounted installation.
Lightning protection
Sensor Station
To protect the controls inside. Is
used in combination with the
Outside Sensor Box or Compact
Sensor.
Electronic lightning protection power supply
Electronic lightning protection RS 485
The Sensor Station consists
of an aluminium mast with
pre-mounted and pre-wired
Outside Sensor Box, 4 sun sensors, 1 wind sensor and 1 outside
temperature sensor. The Sensor
Station can be equipped with
additional sensors such as sun
sensors and a rain sensor. Wall
brackets included.
9 001 629
9 001 630
Measurements / mast height:
3200 mm
Sensor Station
Sensor Station without sensors
9 013 726
9 014 301
Roof mounting
For the installation of Sensor
Station on roof. Stainless steel.
Roof mounting
Strain connection for roof mounting only
[ 153 ]
9 014 300
9 014 303
animeo IB+ Compact accessories
Wind Sensor (not heated)
Outside Temperature Sensor
With solar radiation sensor
shelter.
Measurements:
Degree of protection:
Wiring recommendations:
Height 200 mm, ø 240 mm
max. ø-mast: 48 mm
IP 65
2 × 1,5 mm
Wind Sensor (not heated)
9 001 608
Measurements:
Degree of protection:
Wiring recommendations:
Height 150 mm, ø 115 mm
IP 65
2 × 0,8 mm
Outside Temperature Sensor
9 001 611
Rain Sensor
Heated Wind Sensor
With direct 24 V power supply
over the Outside Sensor Box.
Power supplied via outside
sensor box.
Measurements (W x H x D):
Degree of protection:
Wiring recommendations:
Heated Wind Sensor
Measurements (W x H x D):
Degree of protection:
Wiring recommendations:
Height 190 mm, ø 240 mm
max. ø-mast: 48 mm
IP 54
5 × 1,5 mm
50 × 90 × 40 mm
IP 65
3 × 1,5 mm
Rain Sensor
9 001 610
9 140 180
Sun Sensor
For direct connection on the
Outside Sensor Box.
DCF Receiver
For time synchronisation with
clock in Frankfurt. Pluggable
directly in the Outside Sensor
Box.
DCF Receiver
Measurements (W x H x D):
Degree of protection:
Protection class:
Wiring recommendations:
Angle position:
9 001 612
Sun Sensor without mounting bracket
Mounting bracket for Sun Sensor
[ 154 ]
34 × 88 × 47 mm
IP 43
III
2 × 0,8 mm
150 °
9 050 100
9 127 888
animeo ib+ premium
Higher performance, more functions.
animeo IB+ is a high performance and
intelligent solution for dynamic façade
management. animeo IB+ efficiently
regulates natural daylight, room tem-
perature and natural air-conditioning.
The system offers complete flexibility
and freedom and allows every room
user the exact desired controlling
of their living and working climate.
animeo IB+ is a favourably priced high
performance system for controlling
façades.
Outside Sensor Box and eventual extension box: The Outside
Sensor Box is usually mounted on a Sensor Station. When the
number of existing sensor inputs is insufficient, the Outside
Sensor Extension Box can be used.
8x
4x
2x
Outside
Direction
DCF
2x
2x
Outside
OPTIONAL
Zone
controlling
4x
Inside
2x
OPTIONAL
Zone
controlling
4x
OPTIONAL
Inside
+
Outside Sensor Box
Outside Sensor
Extension Box
Inside Sensor Box 1
Inside Sensor Box 2
PC Software or
Operating Interface
(up to 8 zones).
PC software for
configuration and operation
Building Controller
for zones 1 to 8
Building Controller
for zones 9 to 16
Central Controlling
1 to 16 Controlling Technology
(IB or IB+)
Motor
Controller
devices
Motor Controller devices:
To control motors and connection to e. g. local push
buttons
IB
IB+
M
M
M
animeo IB+
1 AC Motor
Controller
WM
Centralis Uno IB VB
M
M
M
animeo
Motor
Controller
AC, DC, DC-E
(wallmounted)
animeo IB+
1 AC Controller
Circuit board
animeo 4 AC Motor
Controller (DIN-rail mounted)
[ 155 ]
animeo ib+premium
animeo IB+ Premium
contributes to
the development of
bioclimatic façades.
· Sun function with settable thresholds, delays, positions,
slat angle, free sensor assigning, all per zone.
· Sun Tracking: Instead of a fixed position, up to three different positions can be moved to, each per zone. These
three positions can be pre-calculated with the software
and be different for each month. Manual entering of values in the system is possible.
· Wind security function in combination with wind direction: In order to extend the life of the blinds by certain
wind strengths, one can move to a safe position, but only
when the wind direction applies to this zone. Only with
strong winds will all blinds move to the safety position.
· Rain and snow safety functions with settable delay times,
each per zone.
· Ice safety function with settable temperature threshold,
delay times, each per zone.
· Zone timer with two settable time zones per day to configure an up, down or position command.
· Central timer with two settable time zones per day to configure an up or down or position command.
· Potential free main alarm input with configurable action
per zone: up or down command with blocking.
· DCF-77 (radio controlled clock, Frankfurt) time difference
adjustment (optional with Outside Sensor Box) works
within a radius of approx. 1500 km from Frankfurt, Germany.
· Password protection for settings.
· Potential free error output which signals e. g. in the event
of sensor dropout.
· Link to Building Management Systems (BMS) possible
through animeo IB+ Premium OPC Software.
Product advantages
· A system with one Building Controller can control up to 8
zones (façade orientation). A system with 2 Building Controllers controls up to 16 zones.
· Optimised energy savings in combination with a variety of
functions: natural air-conditioning, cooling, heating.
· Advanced operating mode: higher room-suited user comfort through pressing down of non-security functions (e. g.
sun) as soon as local operation has been assigned. The
system switches again to automatic at a pre-defined time.
· Limited tilting angle of the Venetian blinds for the room
user guarantee energy savings and provide nevertheless
exceptional lighting comfort.
· Compatible with all Motor Controller devices from the
Somfy Controlling technology. For maximum functionality
we recommend animeo IB+ Motor Controller devices.
Further features
· One system can encompass up to 6,400 motors.
· User-friendly configuration software (for the start-up,
good knowledge of sun protection and window controlling is recommended in order to achieve maximum system
performance).
· User-friendly and intuitive operating software.
· With system of up to 8 zones, free selection of the
Operating Interface: PC software or Operating Interface
(Operating Interface with reduced functionality compared
to the software).
· Building Controller and Operating Interface can be installed
separately; user interface e. g. in caretaker / facility manager room.
· Through separation of the sensor interfaces (Outside Sensor Box) that are usually mounted outside and the Central
Controller (Building Controller) mounted inside, it is possible to integrate very favourably-priced, system lightning
protection.
· Communication between the Outside Sensor Box and
Building Controller is monitored.
· Very extensive and comprehensive selection of functions
and parameters, specially matched to the type of end
product to be controlled such as Venetian blinds, blinds,
roller shutters and windows.
Important for site managers
· Very high performance and easy to configure system (configuration time: approx. 1 hour).
· User-friendly PC software.
· Optimised energy savings through splitting in separate
zones (up to 16) and additional sensors and software functions.
· Higher user comfort in combination with animeo IB+
Motor Controller devices (see “advanced operating mode”
under “product advantages“).
[ 156 ]
animeo ib+ premium
Solution example
Desired functionality
A “large” project with more than four façade orientations,
enhanced sensor functions, a PC user interface and multiple
Motor Controllers.
Desired functionality
Up to 8 separate façade zones are to be controlled. Six
façades are fitted with exterior Venetian blinds (AC motors),
another with interior Ventian blinds (DC-E motors). A courtyard is fitted with window motors. The HVAC system delivers
opening and closing commands over a potential free contact.
For the user interface an ergonomic PC software is desired.
However, the PC does not have to be connected to the controlling system all the time, except when a data archiving
function for sensor values, system actions etc. is desired. It
should be possible later, over the OPC interface, to link with
a BMS System. The management office rooms should be able
to be upgraded with radio controlling (requires animeo IB+
Motor Controller devices).
Automatic functions
1. Wind safety, as well as wind direction dependent (safe also
for window motors).
2. Rain monitor (safe also for window motors).
3. Sun automatic.
4. When a room user accesses the system via local operation,
the sun automatic is deactivated until midday or until
evening (for this function, animeo IB+ Motor Controller
devices are necessary, otherwise Inteo IB or CD-IB are also
possible).
5. In summer, the available Venetian blinds tilting angle for
the room user can be limited (e. g. maximum up to 45 °
open) so that the cooling system is not overloaded and
that energy for cooling is saved (for this function, animeo
IB+ Motor Controller devices are necessary, otherwise Inteo
IB or CD-IB are also possible).
The solution
+
+
Operating Software
9 012 519
Page 63
Building Controller
1 822 064
Page 63
+
+
Push button
Centralis IB
1 810 138
Page 48
+
animeo Power
Supply DC
1 860 093
Page 65
Sensor station
wall-mounted
9 013 727
Page 66
animeo Motor
Controller device
1 860 049
Page 70
+
RTS radio module
room control device
1 860 105
Page 72
[ 157 ]
Telis 4 Modulis RTS Lounge
1 810 664
Page 72
animeo ib+ premium
Solution in building
M
Motors
M
M
M
W
N
S
O
Building orientation
M
Motors
M
M
M
[ 158 ]
Engineering room
animeo ib+ specif ication
software “quick-quote”
Error-free and efficient planning for animeo IB+ Compact and
animeo IB+ Premium projects
What is the animeo
specification software?
A software tool that can be used for
greater planning assurance for automatic sun protection systems.
What important advantages does
the animeo IB+ specification
software offer?
· The planning process for sun protection is clearly structured.
· Comprehensive and very user-friendly
software.
· With the animeo IB+ specification
software, 80 % of usual building types
can be planned.
· When all basic information / function
preferences are available, you plan
the façade automation system within
30 minutes.
· The animeo IB+ specification software automatically generates a text
for tender which is either based on
Somfy products or neutral. The text for
tender is always individually customised and generated for the configured
project.
· Hardly any product-specific knowledge is required. The software asks
the right questions.
· On the basis of this specification, an
exact and reliable budgeting and
planning for sun protection controlling is possible.
The animeo IB+
specification software
As we are continuously implementing
new devices and updating our software, you may request the latest version from Somfy free of charge.
[ 159 ]
animeo IB+ Premium
animeo IB+ Building Controller
• Rain and snow safety function
with settable delay times,
both for each area.
• Ice safety function with settable temperature threshold
value and delay times, both
for each zone.
• Zone timer with two settable
time ranges per day for the
configuration of an UP and
DOWN or position command.
• Central timer with two settable
time ranges per day for the
configuration of an UP and
DOWN command.
Product advantages
• A system with one Building
Controller can control up to
eight zones (façade orientation) and a system with two
Building Controllers can control
up to 16 zones.
• Optimised energy saving in
conjunction with a wide range
of functions: Natural ventilation, cooling, heating.
• Enhanced operating mode:
Increased, room-based user
comfort thanks to the suppression of centralised non-safety
functions (for example, sun
function) as soon as local controls are used. The system is
switched back into automatic
mode at three freely definable
times each day.
• Restricted Venetian blinds
tilting angles for room users
ensure energy saving whilst
still enabling excellent lighting
comfort.
• Compatible with all conventional Motor Controllers
(animeo IB+, Inteo and CD).
For maximum functionality, we
recommend animeo IB+ Motor
Controllers.
Measurements (W x H x D):
Degree of protection:
Protetion class:
Operating voltage:
Environment temperature:
210 × 90 × 61 mm
IP 20
II
230 V AC
0° C to +45° C
animeo IB+ Building Controller
1 822 064
For DIN-rail installation, 12 SUs.
Other features
• One system can control up to
6400 motors.
• User-friendly configuration
software (for setup, it is recommended that the technician
has a good knowledge of sun
protection and window control
systems in order to ensure the
best possible system performance)
• User-friendly and intuitive
Operating software
• Free choice of operating interface for systems with up to
eight areas: PC software or Operating Interface (with reduced
functions).
• The Building Controller and
Operating Interface can be
installed separately with, for
example, the Operating Interface in the control room.
• The separation of the Sensor
Interface (Outside Sensor Box),
which is normally mounted
outside, and the control center
(Building Controller), which
is normally mounted inside,
enables extremely cost-effective lightning protection for
the system.
• Communication between the
Outside Sensor Box and the
Building Controller is monitored.
• Potential-free main alarm
input with configurable
action per area: UP and DOWN
command with lock.
• DCF-77 time levelling (optional
with Outside Sensor Box)
• Password protection for settings.
• Potential-free defect output if,
for example, a sensor fails.
• Connection to Building Management System (BMS) possible
using OPC Plug-in software.
Operating Software + Interface
• Extensive yet clear selection
of functions and parameters
which are specially tailored to
the type of end product to be
controlled (Venetian blinds,
blinds, roller shutters, and
windows)
• Sun function with settable
threshold values, delays, position, angled orientation for
Venetian blinds, freely defined
sensor assignment, for each
zone
• Sun tracking: Instead of one
fixed position, up to three
different positions can be actuated per day for each zone.
These three positions can be
pre-calculated by the software
and can differ for each month.
They can be manually maintained in the system.
• Wind safety function in combination with wind direction:
To increase the lifetime of the
blind elements, they can be
moved into a safety position if
a certain wind force is reached
and if the wind direction is
such that the specific zone is
affected.
• The blind elements are only
moved into the safety position
if there are strong winds (gale
warning).
Interface between the Building Controller and the computer
including configuration and user
software.
Product advantages
· User-friendly screen display:
large, high, good resolution,
multi-coloured.
· Intuitively designed, comprehensive and operator-friendly.
· The Operating software is
operable independent of
the location of the installed
Building Controller.
Further features
· For computers with minimum
Intel Pentium II, 500 MHz,
Windows 2000, CD Rom disc
drive, 128 MB storage and 40
MB free hard drive storage.
Software + USB / RS485 Interface
Software + RS 232 / RS485 Interface
[ 160 ]
9 012 519
9 011 217
animeo IB+ Premium
animeo IB+ Premium OPC Software
Outside Sensor Box / Outside Sensor Extension Box
Outside Extension Sensor Box
For the connection of 4 more
sun sensors and two wind sensors to an animeo IB+ system.
be executed through the Building Management System using
this connection to the animeo
IB+ Premium system: control
of individual zones, switching
between automatic and manual
priority, feedback of sensor status and values, and more.
The animeo IB+ Premium OPC
Software is a plug-in software
which can be used in combination with the animeo IB+ Operating Software 2.2. Through this
the link to Building Management System (BMS) can easily be
established and makes animeo
IB+ Premium systems even more
flexible. Various functions can
Outside Sensor Box
The Outside Sensor Box is the
interface between the weather
station and the Building Controller. All measurement values
are evaluated here and sent
to the Building Controller. It
requires an external 24 V AC / DC
power supply.
The animeo IB+ Premium OPC
Software allows managing up
8 animeo IB+ Premium systems resulting in the control
of max. 128 individual zones.
The animeo IB+ Premium OPC
Software is fully OPC certified
with the OPC foundation rules
and standards.
animeo IB+ Premium OPC Software
Product advantages
· Only two cables (power supply
24 VAC / DC and data cable) must
be laid to the outside.
· Convenient lightning protection
possible as only two cables are
laid to the outside.
9 015 866
Further features
· All sensors incl. Outside Sensor
Box can be fixed to the sensor
station mast.
· Up to 8 sun sensors, 2 wind
sensors, 1 wind direction sensor, 1 rain sensor, 1 outside
temperature sensor as well as
a DCF plug module can be connected to the Outside Sensor
Box. The Outside Sensor Extension Box offers extension possibilities of 2 additional wind
sensors and 4 sun sensors.
Inside Sensor Box
For connection to external push
buttons or key switches per zone
and up to 2 Inside Temperature
Sensors. In an animeo IB+ system, up to 2 Inside Sensor Boxes
can be used.
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
Product advantages
· Window cleaners need no
access to the complete user Interface (display or PC interface).
· The Inside Temperature Sensors
allow easy extendability of
energy saving options of the
system.
Further features
· In an animeo IB+ system, up
to 2 Inside Sensor Boxes can
be used regardless whether 2
Building Controllers are used.
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
210 × 90 × 61 mm
IP 20
II
230 V AC
0 °C to +45 °C
Outside Sensor Box
Outside Sensor Extension Box
For wall mounted installation.
Inside Sensor Box
Product advantages
· Only two cables (power supply
24 VAC / DC and data cable) must
be laid to the outside.
· Convenient lightning protection
possible as only two cables are
laid to the outside.
9 001 614
For DIN-rail installation, 12 SUs.
[ 161 ]
207 × 255 × 90 mm
IP 65
III
24 V AC / DC
-30 °C to +70 °C
9 001 606
9 001 607
animeo IB+ Premium accessories
animeo IB+ Compact Power Supply
Wind Sensor
To supply the Outside Sensor Box
(without heated sensors).
Measurements:
Measurements (W x H x D):
Safety type:
Protection class:
Operating voltage:
Output voltage:
Output current:
Degree of protection:
Wiring recommendations:
57 × 91 × 57 mm
IP 20
II
230 V AC
24 V DC
350 m A
animeo IB+ Compact Power Supply
Height 200 mm, ø 240 mm
max. ø-mast: 48 mm
IP 65
2 × 0,8 mm2
Wind Sensor
9 001 608
1 870 020
For wall mounted installation.
Heated Wind Sensor
Power supplied via
Outside Sensor Box.
animeo Power Supply DC
To supply the Outside Sensor Box
(with heated sensors).
Measurements:
Degree of protection:
Wiring recommendations:
Heated Wind Sensor
Measurements (W x H x D):
130 × 180 × 61 mm
Degree of protection:
IP 20
Protection class:
II
Operating voltage:
230 V AC
Output current:
2,5 A (switch on duration 100 %)
4,5 A (switch on duration 50 %: 3 mins on, 3 mins off)
animeo Power Supply DC
Height 190 mm, ø 240 mm
max. ø-mast: 48 mm
IP 54
5 × 1,5 mm2
9 140 180
Wind Direction Sensor
With high-quality bearing.
1 860 093
For wall mounted and DIN-rail installation.
Lightning protection
Measurements:
To protect the controls inside. Is
used in combination with the
Outside Sensor Box or Compact
Sensor.
Electronic lightning protection power supply
Electronic lightning protection RS 485
Degree of protection:
Wiring recommendations:
Wind Direction Sensor
9 001 629
9 001 630
[ 162 ]
Height 303 mm,
Arrow length 515 mm,
max. ø-mast: 48 mm
IP 54
5 × 1,5 mm2
9 013 807
animeo IB+ Premium accessories
Outside Temperature Sensor
DCF Receiver
For time synchronisation with
clock in Frankfurt. Pluggable
directly in the Outside Sensor
Box.
With solar radiation sensor
shelter.
Measurements:
Degree of protection:
Wiring recommendations:
Height 150 mm, ø 115 mm
IP 65
2 × 0,8 mm
Outside Temperature Sensor
DCF Receiver
9 001 612
9 001 611
Sensor Station
The Sensor Station consists
of an aluminium mast with
pre-mounted and pre-wired
Outside Sensor Box, 4 sun sensors, 1 wind sensor and 1 outside
temperature sensor. The sensor
station can be equipped with
additional sensors such as sun
sensors and a rain sensor. Wall
brackets included.
Rain Sensor
With direct 24 V Power Supply via
the Outside Sensor Box.
Measurements (W x H x D):
Degree of protection:
Wiring recommendations:
50 × 90 × 40 mm
IP 65
3 × 1,5 mm2
Rain Sensor
Measurements / mast height:
9 001 610
Sensor Station
Sensor Station without sensors
Sun Sensor
3200 mm
9 013 726
9 014 301
Sensor Station Extended
For direct connection on the
Outside Sensor Box.
Measurements Sun Sensor (W x H x D):
Degree of protection:
Protection class:
Wiring recommendations:
Angle position:
Sun Sensor without mounting bracket
Mounting bracket for Sun Sensor
The Sensor Station consists of
an aluminium mast with premounted and pre-wired Outside
Sensor Box, 8 sun sensors,
1 wind sensor, 1 wind direcion
sensor, rain sensor and outside
temperature sensor. Wall brackets included.
34 × 88 × 47 mm
IP 43
III
2 × 0,8 mm
150 °
9 050 100
9 127 888
Measurements / mast height:
Sensor Station extended
[ 163 ]
3200 mm
9 013 727
animeo IB+ Premium accessories
Roof mounting
For the installation of Sensor
Station on roof. Stainless steel.
Roof mounting
Strain connection for roof mounting only
9 014 300
9 014 303
Housing for Inside Temperature Sensor
Measurements (W x H x D):
75 × 75 × 25 mm
Housing for Inside Temperature Sensor
9 008 045
Inside Temperature Sensor
With 1 m cable.
Inside Temperature Sensor
9 008 044
[ 164 ]
animeo ib+
motor controller
animeo IB+ Motor Controller
contribute to
the development of
bioclimatic façades.
animeo IB+ is the favourite amongst the Motor Controlling devices and offers the best price for performance.
Product advantages
Further product features
· Maximum utility for minimum costs in combination with
animeo (Compact) Building Controller.
· Easy installation and quick maintenance:
· Easy and quick start-up in combination with animeo
(Compact) Building Controller. Also through the status
display of the LED’S on the Motor Controlling device.
· Direct counter commands via local operation possible
when central commands without priority (e. g. sun) have
been pre-assigned.
1. Quick assembly
· Integrated tension relief, usable with cable ties
2. Quick connectivity
· Spring connectors clip
· Double connectors (in-out), for example to connect to
the mains circuit
3. Quick maintenance
· Fuse holder per motor output accessible from the
outside
Important for site managers
· Maximum user comfort and energy savings in combination
with animeo IB+ Building Controller.
· Note that devices with this symbol can be upgraded with
radio technology for local control.
1.
Local control
with Radio
Technology
Somfy®
2.
3.
· Priority management between local and central comands
sthrough different operation modes, settable via animeo
(Compact) Building Controller.
· Motor position management in the controlling device per
output instead of in the Central Control leads to minimal
“dark phases” for the room user (move and tilt time settable per motor).
· Possibility to limit the tilting angle of the Venetian blinds
through local operation guarantees energy savings and
offers more lighting comfort.
· Note that devices with this symbol can be upgraded with
radio technology for the local control.
Local control
with Radio
Technology
Somfy®
[ 165 ]
animeo IB+ Motor Controller
4 AC Motor Controller
1 AC Motor Controller
1 AC Motor Controller
For roller shutters, screens, exterior Venetian blinds, exterior
Venetian blinds with 3 end
limits and windows. For the
individual controlling of 1 x 230
VAC motor via local push
buttons, or in groups with IB+
Controlling Technology.
For roller shutters, screens,
exterior Venetian blinds and
windows. For the individual
controlling of 4 x 230 VAC motors via local push buttons, or
in groups with IB+ Controlling
Technology.
Product advantages
· Upgradable for local controlling
per radio or infrared.
· Local setting of an intermediate position and of user
ergonomics.
1 AC Motor Controller
Output Converter
Provides 1 x potential free output
for the individual controlling via
local push buttons, or in groups
with animeo IB+ Controlling
technology.
Further features
· VDE certified.
· Further functionality: window
contact and presence detector
can be connected through the
Motor Controller Extension Box.
· Easy accessible safety fuses per
output.
Product advantages
· Compact construction form
suitable for e. g. installation in
under-window or wall
mounted wiring channels.
· Local setting of an intermediate position and of user
ergonomics.
Local control
with Radio
Technology
Somfy®
Further features
· Easy accessible fuses.
Protection class:
Operational voltage:
Environment temperature:
Output voltage:
Output current:
II
230 V AC
0 °C to +45 °C
230 V AC
max. 3,15 A per output
Measurements (W x H x D):
Degree of protection:
255 × 180 × 61 mm
IP 20
4 AC Motor Controller WM
1 860 049
For wall mounted installation.
Protection class:
Operational voltage:
Environment temperature:
Output voltage:
Output current:
II
230 V AC
0 °C to +45 °C
230 V AC
3,15 A
Measurements (W x H x D):
Degree of protection:
90 × 180 × 45 mm
IP 20
1 AC Motor Controller WM
1 AC Motor Controller WM 3 end limit
1 860 121
1 860 123
For wall mounted installation.
Measurements (W x H x D):
Degree of protection:
4 AC Motor Controller DRM
210 × 90 × 61 mm
IP 20
Operational voltage:
Output current:
max. 230 V AC
max. 3,15 A
1 860 081
1 AC Motor Controller WM Output Converter
For DIN-rail installation, 12 SUs.
1 860 125
For wall mounted installation.
Measurements (W x H x D):
Degree of protection:
4 AC Motor Controller Wieland
255 × 180 × 61 mm
IP 20
65 × 105 × 20 mm
according to installation type
1 860 103
Wieland Plug system compatible.
Measurements (W x H x D):
Degree of protection:
Measurements (W x H x D):
Degree of protection:
254 × 180 × 90 mm
IP 54
[ 166 ]
1 AC Motor Controller Platine
1 AC Motor Controller Platine 3 end limits
1 AC Motor Controller Platine Output Converter
1 860 122
1 860 124
1 860 126
Platine version for DIN-rail installation. Additional DIN-rail adaptor
needed.
animeo IB+ Motor Controller
4 DC Motor Controller
4 DC / DC-E Motor Controller
Product advantages
· Upgradable for local controlling
per radio or infrared.
· Local setting of an intermediate position and of user
ergonomics.
· Settable slats and turning
speed for optimum user ergonomics.
For interior blinds, interior
Venetian blinds and windows.
For the individual controlling of
4 x 24 VDC motors via local push
buttons, or in groups with IB+
Controlling Technology. External
24 VDC power supply required
(see accessories).
For interior blinds, interior
Venetian blinds and windows.
For the individual controlling of
4 x 24 VDC / DC-E motors from the
“Somfy Concept 25” series via
local push buttons, or in groups
with IB+ Controlling Technology.
Further features
· Output protected through current detection.
· Further functionality: window
contact and presence detector
can be connected through the
Motor Controller Extension Box.
Product advantages
· Easy installation: integrated
230 VAC power supply.
· In combination with the DC
encoder motor and the CTS
wind-up system, it allows for
a particularly precise setting of
Local control
with Radio
Technology
Somfy®
Measurements (W x H x D):
Degree of protection:
Protection class:
Operational voltage:
Environment temperature:
Output voltage:
Output current:
Measurements (W x H x D):
255 × 180 × 61 mm
Degree of protection:
IP 20
Protection class:
II
Operational voltage:
230 V AC
Environment temperature:
0 °C to +45 °C
Output voltage:
24 V DC
Output current:
max. 0,5 A continous current per output
1 860 086
For wall mounted installation.
Control diagram and connection plans can be found in the
appendix under ESY 07 018.
4 DC / DC-E Motor Controller WM
For wall mounted installation.
animeo IB+ DALI Interface
The blind positions (height and
angle) are stored just like lighting scenes. Whenever the saved
scene is called up, the blind
moves to the present position. It
is possible to save and recreate
a scene using the DALI SC, for
instance. This makes it possible
to save light and blind positions
in a single scene.
Measurements (W x H x D):
Degree of protection:
animeo IB+ DALI interface
Further features
· Output protected through
current identification.
· Further functionality: window
contact and motion detector
can be connected through the
Motor Controller Extension Box.
Local control
with Radio
Technology
Somfy®
255 × 180 × 61 mm
IP 20
III
24 V CD
0 °C to +45 °C
24 VDC
up to max. 2,1 A per output
4 DC Motor Controller
the slats and an exact postioning of the Venetian blinds.
· Settable up and down speed
(in combination with an animeo IB+ Building Controller)
· Upgradable for local controlling
per radio or infrared.
· Local setting of an intermediate position and of user
ergonomics.
· Settable slats and turning
speed for optimum user ergonomics.
• For integrating animeo
IB+Motor Controllers in the
DALI circuit.
• The interface requires 4 DALI
addresses and can therefore
independently control up to
4 blinds (i. e. 1 interface is
needed per motor controller).
• Lighting moods can be conjured up using different blind
positions.
• The interface supports 16 DALI
groups and 16 DALI scenes. It
is invorporated into the DALI
circuit like a DALI electronic
ballast.
255 × 180 × 61 mm
IP 20
1 860 140
For wall mounted installation.
[ 167 ]
1 860 087
animeo IB+ accessories
RTS Radio module – room operation
Centralis RTS
Receiver for upgrading from
4 AC, 4 DC or 4 DC / DC-E Motor
Controlling devices. Direct plugin to Motor Controller or Motor
Controller extension box.
1-channel radio wall transmitter.
New
design
available from
quarter 1
2011
Local control
with Radio
Technology
Somfy®
Measurements (W x H x D):
80 × 80 × 17 mm
Centralis RTS
Measurements (W x H x D):
52 × 92 × 27 mm
RTS Radio module
1 810 090
Delivery incl.: Switch, including inteo cover plate, inteo cover plate
frame and fixing screws.
1 860 105
Telis 1 Modulis RTS
Telis 1 RTS
Telis 1 RTS
Pure
Telis 1 RTS
Silver
Telis 1
Modulis
RTS Pure
Telis 1 RTS
Lounge
1-channel radio hand transmitter, manual controlling of one or
more motors per radio.
radio. Comfortable setting of the
slats through a handwheel.
Telis 1 Modulis RTS Pure
Telis 1 Modulis RTS Silver
Telis 1 Modulis RTS Lounge
1 810 630
1 810 637
1 810 649
1 810 974
1 810 975
1 810 976
Delivery incl.: hand transmitter including wall bracket and battery.
Delivery incl.: hand transmitter including wall bracket and battery.
Telis 4 Modulis RTS
Telis 4 RTS
Telis 1 RTS
Pure
Telis 1
Modulis
RTS Lounge
1-channel radio hand transmitter, manual controlling of one or
more Venetian blind motors per
Telis 1 RTS = 1-channel:
individual and group operation
possible.
Telis 1 RTS Pure
Telis 1 RTS Silver
Telis 1 RTS Lounge
Telis 1
Modulis
RTS Silver
Telis 1 RTS
Silver
Telis 4
Modulis
RTS Pure
Telis 1 RTS
Lounge
5-channel radio hand transmitter, manual controlling of one or
more motors per radio.
Telis 4
Modulis
RTS Lounge
5-channel radio hand transmitter, manual controlling of one
or more Venetian blind motors
per radio. Comfortable setting of
Telis 4 RTS = 5-channel:
individual and group operation
possible.
Telis 4 RTS Pure
Telis 4 RTS Silver
Telis 4 RTS Lounge
Telis 4
Modulis
RTS Silver
1 810 631
1 810 638
1 810 651
Telis 4 Modulis RTS Pure
Telis 4 Modulis RTS Silver
Telis 4 Modulis RTS Lounge
Delivery incl.: hand transmitter including wall bracket and battery.
the slats through a handwheel.
Telis 4 Modulis RTS = 5-channel:
individual and group operation
possible.
1 810 765
1 810 663
1 810 664
Delivery incl.: hand transmitter including wall bracket and battery.
The listed products use the 433 MHz frequency.
[ 168 ]
animeo IB+ accessories
animeo Power Supply DC
Push Button Centralis IB
To supply the Outside Sensor Box
(without heated sensors).
Manual controlling of several
motors over IB-Bus. Comfortable Central Control or group
operability. Operation via the big
UP, DOWN and STOP buttons is
possible at any time.
Measurements (W x H x D):
130 × 180 × 61 mm
Degree of protection:
IP 20
Protection class:
II
Operating voltage:
230 V AC
Output current:
2,5 A (switch on duration 100 %)
4,5 A (switch on duration 50 %: 3 mins on, 3 mins off)
animeo Power Supply DC
Centralis IB
1 810 138
Delivery incl.: Switch, including inteo cover plate, inteo cover plate
frame and claws.
Centralis IB
1 800 278
Delivery incl.: Switch and matching cover (see selection in appendix
but without cover plate).
1 860 093
For wall mounted and DIN-rail installation.
IB / IB+ Repeater
animeo switch zone splitter
Circuit board for signal amplification of IB / IB+ Controlling
Technology signal with longer
cable connection (from 1000 m).
For creating sub-groups within
an IB+ zone.
Measurements (W x H x D):
Degree of protection housing:
Protection class:
Measurements (W x H x D):
Degree of protection:
Protection class:
Operating voltage:
Environment temperature:
80 × 80 × 52 mm
IP 65
III
animeo switch zone splitter
165 × 160 × 60 mm
IP 54
II
230 V AC
0 °C to + 40 °C
IB / IB+ Repeater
1 810 392
9 011 809
For wall mounted installation.
animeo IB+ Wiring Test Tool
DIN-rail adaptor
To ensure that the system is
properly wired.
For installation on 35 mm DINrail for mounting of circuit board
versions CD 1 x 1 P6, CD 2 x 1 P6,
CD 1 x 4 P6, animeo 1 AC Motor
Controller.
Measurements (W x H x D):
DIN-rail adaptor
animeo IB+ Wiring Test Tool
70 × 105 × 23 mm
9 000 910
For 35 mm DIN-rail, colour; black, 4 SUs.
[ 169 ]
1 810 793
Controls
REMOTES & ACCESSORIES
Telis Collection................................................. 171
Remote Operation ........................................... 172
Hand Held RTS Remotes .................................... 173
RS485 RTS Transmitter ...................................... 175
RS 485 ILT Interface .......................................... 176
Wall Mount - RTS Transmitters ............................ 177
Hand Held - IR Transmitters............................... 177
Indoor and Outdoor - RTS Sensors ....................... 178
Indoor and Outdoor - RTS Receivers / Lighting &
Heating Receivers / Indoor RTS Receivers ................ 179
Electronic Switches / Mechanical Switches .............. 180
Motor Controllers / PowerSupplies - 24V ................ 182
Controllers Switches ........................................ 184
TELIS COLLECTION
LOUNGE FINISH
For high end
sophisticated decor.
SILVER FINISH
Fits naturally within
a contemporary
decor.
My button:
You can program the clients
favourite position and nd
it automatically simply by
pressing the “my” button
of the remote control.
PATIO FINISH
Stylish design for
outdoor use.
PURE FINISH
Simple, straight
forward and
functional.
Number of Channels
TELIS 1 RTS
TELIS 4 RTS
TELIS SOLIRIS RTS
1
5
1
•
•
•
Activation/ Deactivation
of Sun feature
Venetian Blade
Orientation
Telis 4 Modulis RTS
TELIS SOLIRIS 4
5
16 RTS
16
•
Only on the 5th channel
Telis Modulis Soliris RTS
•
Remote Channel Screen
FINISHES
Pure
Silver
Patio
Lounge
•
•
•
•
•
•
•
•
•
•
•
•
Telis Modulis Soliris RTS
•
•
Telis Modulis Soliris RTS
[ 171 ]
•
REMOTE OPERATION
Moving the End Product
>Product Stationary
Press = move to “my”
position order
Press = up
order
>Product in motion
Press = stop order
Press = down
order
Channel Selection (TELIS 4)
>Successive Presses =
channel selection
>The fifth channel is selected
when 4 LEDs flash
simultaneously
Activate / Deactivate “Sun” Function (TELIS SOLIRIS)
Combination button:
- Channel Selection
>Successive presses to select the
required channel
>The fifth channel is selected when
all 4 LEDs flash simultaneously
>Long Press = activate or
deactivate the “sun” function
- Enable/ Disable the “sun” function
>Long Press only on the fifth
channel
Telis 16 RTS
Possibility to associate an icon to the
channel (optional).
Channel number
Possibility to name each channel
and associate a number
Channel Selection
Press = Up order
Product stationary
Press = move to “my” position order
Product in motion
Press = stop order
Press = Down order
[ 172 ]
CONTROLS
HAND HELD - RTS REMOTES
PURE
SILVER
LOUNGE
PATIO
TELIS 1 RTS
One channel radio remote.
Allows for the individual or group control of RTS
motors / receivers. Somfy Rolling Code. 200m range
in an open area and up to 20m range through two
reinforced concrete walls.
Frequency: 433.42MHz.
IP30 (except for Patio: IP44).
Supplied with wall mount.
Ref.
1810630
Ref.
1810637
Shock Resistant
Ref.
1810649
Ref.
Shock Resistant
1810642
Dimensions: 145 x 49 x 22mm.
(except for Pure: 134 x 41 x 21mm)
Shock Resistant
Splash Proof
PURE
SILVER
LOUNGE
PATIO
TELIS 4 RTS
Five channel radio remote.
Allows for the individual and / or group control of
RTS motors / receivers. Somfy Rolling Code. 200m
range in an open area and up to 20m range through
two reinforced concrete walls.
Frequency: 433.42MHz.
IP30 (except for Patio: IP44).
Supplied with wall mount.
Ref.
1810631
Ref.
1810638
Shock Resistant
Ref.
1810651
Ref.
Shock Resistant
1810644
Dimensions: 145 x 49 x 22mm.
(except for Pure: 134 x 41 x 21mm)
Shock Resistant
Splash Proof
PURE
PATIO
TELIS SOLIRIS RTS
Sun / Wind radio remote.
Allows for the individual or group control of RTS
motors / receivers. Used to inhibit the Sun function.
Somfy Rolling Code.
200m range in an open area and up to 20m range
through two reinforced concrete walls.
Frequency: 433.42MHz.
IP30 (Pure) IP44 (Patio).
Supplied with wall mount.
Ref.
1810634
6
Ref.
1810646
6
Shock Resistant
Dimensions Pure: 134 x 41 x 21mm.
Dimensions Patio: 145 x 49 x 22mm.
Splash Proof
PATIO
TELIS 4 SOLIRIS RTS
Five channel Sun / Wind radio remote.
Allows for the individual and / or group control of RTS
motors / receivers. Used to inhibit the Sun function only
on the fth channel.Somfy Rolling Code. 200m range
in an open area and up to 20m range through two
reinforced concrete walls.
Frequency: 433.42MHz.
IP44.
Ref.
f
1810648
181064
Shock Resistant
NOTE: Replacement battery for:
- Telis 1 and Telis 4, 3V type CR2430 (Somfy Part # 9014943)
Splash Proof
[ 173 ]
Supplied with wall mount.
Dimensions: 145 x 49 x 22mm.
CONTROLS
HAND HELD - RTS REMOTES
PURE
SILVER
LOUNGE
TELIS MODULIS 1 RTS
One channel radio remote with Tilt Wheel. Allows for the
individual control of Modulis RTS receiver, 4AC Motor
Controller RTS card, Integrated DC Receiver or DC RTS Receiver.
Somfy rolling code. 200m range in an open area and up to
20m range through two reinforced concrete walls.
Frequency: 433.42MHz
IP30
Supplied with wall mount
Ref.
1810974
Shock Resistant
Ref.
1810975
Shock Resistant
Ref.
1810976
Dimensions: 145 x 49 x 26mm
Shock Resistant
Suitable only for tilting blade applications.
PURE
SILVER
LOUNGE
TELIS MODULIS SOLIRIS RTS
Sun / Wind radio remote with Tilt Wheel. Allows for the
individual or group control of Modulis RTS Receiver, 4AC Motor
Controller RTS card, Integrated DC Receiver or DC RTS Receiver.
Somfy Rolling Code. 200m range in an open area and up to
20m range through two reinforced concrete walls.
Frequency: 433.42MHz.
IP30.
Supplied with wall mount.
Ref.
1810666
Shock Resistant
Ref.
1810666
Shock Resistant
Ref.
1810665
Dimensions: 145 x 49 x 26mm.
Shock Resistant
Suitable only for tilting blade applications.
PURE
SILVER
LOUNGE
TELIS 4 MODULIS RTS
Five channel radio remote with Tilt Wheel. Allows for the
individual and / or group control of Modulis RTS Receiver, 4AC
Motor Controller RTS card, Integrated DC Receiver or DC RTS
Receiver. Somfy Rolling Code. 200m range in an open area and
up to 20m range through two reinforced concrete walls.
Frequency: 433.42MHz.
IP30.
Supplied with wall mount.
Ref.
1810663
Ref.
1810663
Shock Resistant
Shock Resistant
PURE
SILVER
Ref.
1810664
Dimensions: 145 x 49 x 26mm.
Shock Resistant
Suitable only for tilting blade applications.
TELIS 16 RTS
16 channel radio remote
Allows for the individual or group control of 16 RTS
motors /receivers. LCD screen.
Somfy rolling code. 200m range in oen area and 20m
through two reinforced concrete walls.
Frequency: 433,42 Mhz
IP30
Supplied with wall mount
Dimensions: 145 x 47 x 18mm.
Ref.
1811020
Shock Resistant
Ref.
1811021
Shock Resistant
[ 174 ]
Controls
RS485 RTS TRANSMITTER
The RS485 RTS Transmitter is a motor controller for all Somfy RTS
motors and receivers. It converts RS485 Somfy command coming
from home control systems into RTS orders.
Ref. 1810803
Up to 16 RTS adresses: the interface can manage up to 16 groups of
RTS products from the RS485 network and from dry contact inputs
(x5). Each group can control several motors and receivers.
Function with RTS motors & receivers: open, close, stop, record a
favorite light level, open the programming mode, dim up and
down.
Function with RTS lighting receiver: record a favorite light level,
open the programming mode, dim up and down.
The RS485 Transmitter cannot set motors end limits.
Mounting on DIN Rail with both plastic clips and wall mountings
using 2 screws (diameter 4mm).
TECHNICAL DETAILS
Power supply
Power supply frequency
Power supply consumption
Protection Index
Working temperature
Radio Protocol
Radio frequency
Connection dry contact
Connection RS485
Connection Antenna
Connection power supply
Box material
Color
Dimension (mm)
Weight
90 – 255V
50
65 mA @ 90V to 30 mA @255V
IP 20 ( interior product )
0 ˚C to 60 ˚C
RTS U80
433.42MHz
5x phoenix contactor block 3.5mm 3 - pins
1x phoenix contactor block 3.5mm 4 - pins
1 x BNC connector
IE C C8
ABS
Black
( L x I x D ): 175 x 100 x 46
430g (with antenna and power supply cable)
[ 175 ]
CONTROLS
RS485 ILT INTERFACE
The RS485 ILT Interface is a motor controller for multi radio
motortized systems. It can control upto 4 Somfy ILT motors.
Each motor can be set (no need to use the ILT seting tool) and
controlled individually through the interface.
Upto 8 formats can be memorized depending on ratio: 4:3,
16:9, 2, etc.
A group command is also available to raise or lower screens.
It can be used as an interface with infrared remote controls
(Somfy or universal IR remotes) or with RS485 data.
Ref. 1870130
TECHNICAL DETAILS
Power supply
Power supply frequency
Power supply consumption
Protection Index
Working temperature
Connectors IR sensors
Connectors ILT motors
Connectors Trigger Video projector
Connectors RS-485
Box material
90 – 255V
50 Hz
65 mA @ 90V to 30 mA @ 255V maximum
IP 20
0 ˚C to 60 ˚C
1x R J9 phone plug
4x R J9 phone plug
1x Phoenix contact connector block 3.5mm 2pin
1x Phoenix contact connector block 3.5mm 4pin
ABS
Color
Dimension (mm)
Weight
Black
( L x I x D ): 137 x 80 x 40
132g (without power supply cable)
[ 176 ]
CONTROLS
WALL MOUNT - RTS TRANSMITTERS
DRY CONTACT TRANSMITTER
CENTRALIS RTS
RTS Motor programming with dry contact Transmitter.
For one room one transmitter is recommended.
Programmed with remote to operate with one touch
panel, with common up and down.
One channel wall mount radio transmitter.
Allows for the individual or group control of RTS
motors / receivers. Somfy Rolling Code. 200m range
in an open area and up to 20m range through two
reinforced concrete walls.
Frequency: 433.42MHz.
Supplied with wall mount & screws.
Dimensions: 80 x 80 x 16mm.
Ref.
1810135
Ref.
1810090
INIS RT
Wireless switch compatible with all RTS recievers.
One sequencing button for UP,STOP, DOWN, STOP....
Ref.
1810180
HAND HELD - IR TRANSMITTERS
Ref.
IRT 103 INFRARED REMOTE
IRT 803 INFRARED REMOTE
Single channel infrared remote. Allows for
IR control of Somfy products utilising an IR
receiver. 7m range.
Eight channel infrared remote. Allows for IR
control of Somfy products utilising a suitable
multi-channel IR receiver. 7m range.
IP30.
IP20.
Dimensions: 110 x 35 x 15mm.
Dimensions: 180 x 45 x 30mm.
1870011
Ref.
NOTE: Replacement battery for:
- IRT 103 & IRT 803, 2 x 1.5V type AAA.
[ 177 ]
1870132
SENSORS
OUTDOOR, INDOOR & FOR RTS & WT MOTORS
EOLIS RTS SENSOR
Radio sensor that will automatically retract a
screen / awning based on wind speed. Compatible
with Altus RTS, Orea RTS, CSI RTS, Modulis Receiver
and the Universal Receiver. Somfy Rolling Code.
200m range in an open area and 20m range through
two reinforced concrete walls.
Frequency: 433.42MHz.
IP34.
Supplied with wall mount & screws.
Ref.
1816068
Dimensions: 160 x 236 x 25mm.
SOLIRIS RTS SENSOR*
SUNIS RTS SENSOR*
Radio sensor that will automatically retract a screen /
awning based on wind speed and extend / retract based
on a preset amount of sunlight. Compatible with Altus
RTS, Orea RTS, CSI RTS, Modulis Receiver and the Universal
Receiver. Somfy Rolling Code. 200m range in an open area
and 20m range through two reinforced concrete walls.
Radio sensor that will automatically extend a screen /
awning based on a preset amount of sunlight. Powered
connection not required. Compatible with Altus RTS, Orea
RTS, CSI RTS, Modulis Receiver and the Universal Receiver.
Somfy Rolling Code. 200m range in an open area and
20m range through two reinforced concrete walls.
Frequency: 433.42MHz.
Frequency: 433.42MHz.
IP34.
IP44.
Supplied with wall mount & screws.
Ref.
1818212
Supplied with wall mount & screws.
Dimensions: 160 x 236 x 25mm.
Ref.
SUNIS INDOOR WIREFREE SENSOR
9013075
THERMOSUNIS INDOOR WIREFREE SENSOR
Radio sensor that will automatically control an
external blind / shutter based on a preset amount of
sunlight. Not suitable for folding arm or drop arm
awnings. Somfy Rolling Code. 200m range in an open
area and 20m range through two reinforced concrete
walls.
Radio sensor that will automatically control a blind,
shutter or venetian based on a preset amount of
sunlight and inside temperature. Not suitable for
folding arm or drop arm awnings. Somfy Rolling
Code. 200m range in an open area and 20m
range through two reinforced concrete walls.
Frequency: 433.42MHz.
Frequency: 433.42MHz.
IP31.
Supplied with suction cup mount.
Dimensions: Ø55 x 23mm (not including suction cup mount)
IP31.
Supplied with suction cup mount.
Ref.
Ref.
9013707
Dimensions: Ø100 x 50mm.
Dimensions: Ø55 x 23mm (not including suction cup mount)
Ref.
9013708
EOLIS SENSOR
SOLIRIS SENSOR
Wind sensor for use with Soliris IB, Soliris UNO and
Eolis Box controllers. Measures horizontal wind
speed (km/h). Only one sensor can be connected
back to the control unit. Up to seven control boxes
can be connected to the one sensor.
IP33.
Dimensions: 160 x 236 x 115mm.
Combined sun and wind sensor for use with Soliris IB
& Soliris UNO controllers. Measures 360˚ sunlight
intensity (kLux) and the horizontal wind speed
(km/h). Only one sensor can be connected back to
the control unit.
IP33.
Dimensions: 160 x 236 x 115mm.
9101480
Ref.
NOTE: Replacement battery for:
- Eolis 3D RTS 2 x 1.5V type AAA.
*Must be used in conjunction with a Soliris Remote to enable Sun function
[ 178 ]
9101474
RECEIVERS
OUTDOOR RTS RECEIVERS
MODULIS SLIM RECEIVER RTS CABLE*
UNIVERSAL RECEIVER RTS
Outdoor radio receiver with Modulis scroll
functionality for connection to a standard motor
allowing use via an RTS transmitter and RTS sensor.
Compatible only with standard 230V motors.
Outdoor radio receiver for connection to a standard
motor allowing use via an RTS transmitter and RTS
sensor. Compatible only with standard 230V motors.
Frequency: 433.42MHz.
IP55.
Frequency: 433.42MHz.
Supplied with wall mount and screws.
IP54.
Compact high index protection housing.
Dimensions: 110 x 110 x 40mm.
Dimensions: 130 x 32 x 33mm.
Ref.
1810624
Ref.
Sensor Compatible
1810806
Sensor Compatible
LIGHTING & HEATING RECEIVERS
INDOOR LIGHTING RECEIVER RTS
Ref.
LIGHTING DIMMER RECEIVER RTS
Indoor radio receiver for connection to a standard
light allowing use via an RTS transmitter. Can
control virtually any bulb type.
Radio receiver for dimming a standard light via
the Modulis scroll functionality. Can control any
dimmable bulb type.
Frequency: 433.42MHz.
Frequency: 433.42MHz.
IP30.
IP54.
500W max load.
300W max load.
Dimensions: 80 x 80 x 45mm.
Dimensions: 40 x 52.7 x 24.7mm.
1810165
Ref.
9014281
Modulis Compatible
INDOOR RTS RECEIVERS
ACCESSORIES
CENTRALIS INDOOR RECEIVER*
SURFACE BOX FOR CENTRALIS INDOOR
Indoor radio receiver for connection to a standard
motor allowing use via an RTS transmitter.
Compatible with standard 230V motors. Visual motor
programming feedback.
Surface mount box for Centralis Indoor RTS,
Centralis Indoor RTS VB, Busline Transmitter, Dry
Contact Receiver and Indoor Lighting Receiver.
Use when a recess is not available for mounting.
Frequency: 433.42MHz.
Dimensions: 84 x 84 x 44mm.
IP30.
Supplied as flush mount.
Dimensions: 80 x 80 x 45mm.
Ref.
1810096
Ref.
*Not compatible with Rodeo or Linkeo motors.
[ 179 ]
9154122
ELECTRONIC SWITCHES / CONTROLLERS
FOR WT MOTORS
Ref.
Ref.
CENTRALIS UNO IB
EOLIS BOX
Used as the main interface controller for a 230V
AC motor with a busline input for master control
via an IB switch such as the Centralis IB. Two
intermediate positions programmable, along with
a busline disabling switch.
IP40.
Dimensions: 80 x 80 x 50mm.
A 230V AC wind controller interface unit mounted in a
splashproof box suitable for outdoor mounting. IB
switch input. A rain sensor can also be used with the
addition of a rain control board (see sensors).
IP44.
Dimensions: 150 x 150 x 40mm.
1810208
Ref.
1816046
CHRONIS UNO
CENTRALIS IB
230V AC controller for a single motor with timer
function and manual operation. Con gurable one
up, one down time per day that can differ each
day of the week.
IP40.
Dimensions: 80 x 80 x 50mm.
Used as a master control for an IB setup. Can also
be used with any Somfy device that has a Busline
input. eg. FTS Box, 4AC Motor Controller, etc.
IP40.
Dimensions: 81 x 81 x 28mm.
1805007
Ref.
1810094
MECHANICAL SWITCHES
FOR WT MOTORS
KEY SWITCH SURFACE MOUNTED
SPRING
LOADED
DOWN,
FIXED IN UP
DIRECTIONS
A single control key switch for an AC motor. Available as a spring operation in
both “up” and “down” directions or as a spring operation for “down” and
FIxed operation for the “up” direction.
Colour: Grey.
Max Current: 10A.
Weather and burglar proof.
Dimensions: 81 x 71 x 75mm.
Ref.
1850039
[ 180 ]
MECHANICAL SWITCHES
FOR WT MOTORS
STANDARD
MOMENTARY
INIS DUO
5 POSITION
A dual control switch for two 230V AC motors. Available as a standard lock in
(fixed) switch, momentary (spring loaded) or 5 position (spring and fixed).
Colour: White & grey.
Max Current: 6A per switch.
Supplied as wall mount.
Dimensions: 80 x 80 x 42mm.
Ref.
1800192
Ref.
1800025
Ref.
1800001
KEO INIS (SURFACE MOUNTED)
Renovation switch for indoor use only, to control
one motor or a group of motor via a relay box.
Ref.
Ref.
1800031
KEO INIS (RECESSED)
WATERPROOF SWITCH
Fixed position switch for indoor use only, to
control one motor or a group of motor via a relay
box.
Waterproof paddle switch to control one motor or a
relay box controlling a group of motor
1800019
Ref.
1870064
ROCKER SWITCH FIXED POSITION
ROCKER SWITCH MOMENTARY POSITION
Rocker switch momentary position
AC 3 position rocker switch for 230V WT motors.
Momentary position with
phase, neutral, common, up & down
Rocker switch fixed position
AC 3 position rocker switch for 230V WT motors.
Fixed position with phase, neutral,
common, up & down
Ref.
1800150
Ref.
[ 181 ]
1800158
MOTOR CONTROLLERS
FOR WT MOTORS
THREE MOTOR GROUP CONTROLLER
FOUR MOTOR GROUP CONTROLLER
Group control unit, allowing up to three motors
to be connected via a single controller / switch.
No individual control of the connected motors is
possible. The Three Motor Group Controller cannot
be utilised with a standard fixed position switch,
an interlocked / momentary switch is required.
IP40.
Dimensions: 112 x 52 x 106mm.
Ref.
Group control unit, allowing up to four motors
to be connected via a single controller / switch.
No individual control of the connected motors is
possible. The four Motor Group Controller cannot
be utilised with a standard fixed position switch,
an interlocked / momentary switch is required.
IP40.
Dimensions: 150 x 75 x 105mm.
1810054
Ref.
1810058
24V DC POWER SUPPLY
MOTOR SELECTION CHART
The following chart is a guide only.
Refer to the hardware manufacturer for more details.
HOW TO USE THIS SELECTION CHART
• Select the motor desired for the application (‘y’ axis).
• Select the power supply required (‘x’ axis).
• Follow the two until they intersect, the maximum number of motors
that can be utilised from that one power supply will be shown.
• A safety factor has already been taken into account.
POWER SUPPLY
MOTOR TYPES
Power 1.5DC
GPS100
3
9
2
7
3
11
1
2
LV25-B64
LW25-B83
LT28-B73
Sonesse 30
[ 182 ]
CONTROLLERS / POWER SUPPLIES
FOR 24V DC MOTORS
POWER 1.5DC
GPS 100
Power supply for 24V DC Somfy devices. Utilise with
a suitable DC switch or receiver. Regulated output.
LED for power veri cation.
Power supply for 24V DC Somfy devices. Utilise with a
suitable DC switch or receiver. Regulated output.
Nominal Load: 5A (intermittent).
IP40.
Dimensions: 135 x 120 x 44mm.
Nominal Load: 2.7A (intermittent).
IP20.
Dimensions: 110 x 53 x 20mm.
Ref.
Ref.
1870149
1870142
Ref.
INTEGRATED RECEIVER
DC RTS RECEIVER
Radio receiver for 24V DC WT motors. Allows for the
use of an RTS transmitter. Compatible only with
standard 24V WT motors, a suitable power supply is
also required. Suitable headrail adaptors required for
mounting. Rolling code.
Frequency: 433.42MHz.
IP20.
Dimensions: Ø24 x 97mm.
Max. Number of Motors: 2x LV25-B44/ LW25-B44.
2x LV25-B64.
2x LT 28.
2x LW25-B83.
1x Linkeo 2.
1x Rodeo.
Radio receiver for 24V DC WT motors. Allows for the
use of an RTS transmitter. Compatible only with
standard 24V WT motors, a suitable power supply is
also required. Rolling code.
Frequency: 433.42MHz
IP20.
Dimensions: 150 x 25 x 25mm.
Max. Number of Motors: 2x LV25-B44/ LW25-B44.
2x LV25-B64.
2x LT 28.
2x LW25-B83.
1x Linkeo 2.
1x Rodeo.
Ref.
Modulis Compatible
Ref.
1870002
1870035
1870137
Modulis Compatible
IRS 300
IR3 INFRARED SENSOR
Integrated infrared eye and controller for 24V WT DC
motors. Busline input for master control via a Centralis
IB and IR control when utilised with an IRT103 or
IRT803. Tilt control available. A suitable 24V power
supply is required.
Infrared eye for use with the GPS 1020. 2.5m cable
supplied.
IP30.
Supplied white in colour.
Dimensions: 47 x 43 x 34mm.
Max. Number of Motors: 3 x LV25-B44 / LW25-B44.
3 x LV25-B64.
3 x LT 28.
3 x LW25-B83.
1 x Linkeo 2.
2 x Rodeo.
Dimensions: 76 x 50 x 32mm.
Ref.
[ 183 ]
9154186
CONTROLLERS / SWITCHES
FOR 24V DC MOTORS
Ref.
Ref.
1870062
S31 ROCKER SWITCH
S51 ROCKER SWITCH
DC three position rocker switch for 24V DC WT motors.
Used in conjunction with a suitable power supply the
motors power will be inverted when a reversal
of direction is required.
DC five position rocker switch for 24V DC WT motors.
Used in conjunction with a suitable power supply
the motors power will be inverted when a reversal of
direction is required. Tilting accessed by brief presses.
Max. Number of Motor(s): 6 x LV25-B44 / LW25-B44.
5 x LV25-B64.
4 x LT 28.
4 x LW25-B83.
3 x Linkeo 2.
1 x Linkeo 4.
3 x Rodeo.
Max. Number of Motor(s): 6 x LV25-B44 / LW25-B44.
5 x LV25-B64.
4 x LT 28.
4 x LW25-B83.
3 x Linkeo 2.
1 x Linkeo 4.
3 x Rodeo.
Ref.
CENTRALIS DC IB
WHITE PLATE
DC Inteo style switch for the control of 24V DC WT motors.
Busline input for master control via a Centralis IB,
suitable 24V power supply required.
Max. Number of Motor(s): 6 x LV25-B44 / LW25-B44.
5 x LV25-B64.
4 x LT 28.
4 x LW25-B83.
3 x Linkeo 2.
1 x Linkeo 4.
3 x Rodeo.
Dimensions: 80 x 80 x 30mm.
Flush mount plate for S31 and S51 rocker switch.
Requires a reveal behind mounting surface.
Dimensions: 80 x 80mm.
1810153
Ref.
SURFACE BOX
Surface mount box for S31 and S51 rocker switch.
Dimensions: 86 x 42 x 39mm.
Ref.
1870061
9660135
[ 184 ]
9137159
[ 185 ]
Wiring Diagrams
Parallel Wiring................................................ 187
Dual Switching ............................................... 188
RTS motor ..................................................... 189
RTS motor with Sensor ...................................... 190
Keo Iris Recessed .................................................. 191
Centralis Indoor Receiver to a motor ..................... 192
Universal Receiver with Sensor ............................ 193
Centralis IB to three Centralis UNO IB's ................... 194
Chronis IB to three Centralis UNO IB's .................... 195
1AC Motor Controller to a motor ........................... 196
4AC Motor Controller to four motors ...................... 197
Glydea ......................................................... 198
DC RTS Receiver to a DC motor ............................. 201
S type Rocker Switch to a DC motor ....................... 202
FTS Controller ................................................. 203
Lighting Dimmer RTS ....................................... 204
4 Motor Group Controller .................................. 205
IR Receiver AC Motor ........................................ 206
Centralis IB Centralis UNO IB and Motor Group Controller .... 207
Parallel Wiring
[ 187 ]
Dual Switching
[ 188 ]
RTS motor
[ 189 ]
RTS motor with Sun & Wind Sensor
[ 190 ]
Keo Inis
OR
Keo Inis
Surface Mounted
Keo Inis
Recessed
1800031
1800019
Keo Inis’s Recessed
[ 191 ]
Centralis Indoor Receiver to a motor
[ 192 ]
Universal Receiver with Sensor
[ 193 ]
Centralis IB to three Centralis UNO IB's
[ 194 ]
Chronis IB to three Centralis UNO IB's
[ 195 ]
1AC Motor Controller to a motor
[ 196 ]
4AC Motor Controller to four motors
[ 197 ]
Glydea
Individual DCT Control with a Somfy switch
DCT Group Control with a Somfy Switch
[ 198 ]
Glydea
[ 199 ]
Glydea
[ 200 ]
DC RTS Receiver to a DC motor
[ 201 ]
S type Rocker Switch to a DC motor
[ 202 ]
FTS Controller
[ 203 ]
Lighting Dimmer RTS
[ 204 ]
Reference No. 1810058
Compatable with:
fixed or momentart switches
CD4
SM1
somfy Line
Inteo
4 Motor Group Controller
[ 205 ]
Reference No. 1860000
AC Infra-red reciever
IR Receiver AC Motor
[ 206 ]
Reference No. 1810094 and 1810208
Centralis IB and Centralis UNO IB
and Motor Group Controller
[ 207 ]
Somfy India PVT LTD
www.somfy.co.in
www.somfy-architecture.com
New Delhi
26, First Floor, (Front Side)
Okhla Industrial Estate
Phase-III
New Delhi - 110020
Tel: +91 11 46 11 15 55
Fax: +91 11 46 11 15 00
Mumbai
© copyright SOMFY India Pvt. Ltd. 2010
Bangalore
No 318-319, 3rd Floor, B-Wing,
Mittal Towers, MG Road,
Bangalore - 560001
Tel: +91 80 41 26 92 55
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising