Find out what`s behind, in real time

Find out what`s behind, in real time
SV-6922.LM
170° Lip Mount Style
CMOS Color Camera
INSTALLATION INSTRUCTIONS:
The SV-6922.LM is an ultra-small universal lip-mount waterproof back-up camera, designed to
be installed on any vehicle. The small size allows it to fit in almost any location on any vehicle
and the ultra-wide vehicle angle makes it perfect for vehicles with larger blind spots.
This uniquely designed product can be of use for any passenger car, SUV and Van, also can be
of use for large truck, school bus, bus and boat as well. Furthermore, it can not only be installed
on the license plate bezel or trunk lid, but anywhere on the vehicle, such as under the bumper,
on the sides of cargo trailers or above the hatch.
FEATURES:
•
•
•
•
•
•
•
Universal design makes it a good choice to use for any vehicle.
The 170° ultra wide-angle CMOS color camera provides rear images in real time and
eliminates the dangerous “blind-spot” directly behind your vehicle when backing up.
Normal and reverse image selectable
Parking lines to help the driver accurately judge distance behind the vehicle
Constructed of high-grade plastic and durable die-cast metal
Kit includes all necessary parts to allow the camera to be flush mounted or bracket
mounted to any vehicle
Waterproof Design (IP67)
INSTALLATION
MOUNTING:
OPTION 1: BRACKET MOUNTING
1. Find a suitable location on the trunk lip or license plate bezel to secure the mounting bracket
down to the body of the vehicle
2. Use the supplied 3M double-side tape to mount the bracket or you can also use screws to
secure it down. If using screws, make sure to double check behind the mounting surface.
3. Route the wire harness through the rear bumper of the vehicle or through any kind of rubber
grommet on the vehicle. If you have to drill a hole, make sure to seal the hole once you route
the wiring through to prevent leaking or moisture damage.
4. The flexible mounting bracket can be bent to give the driver the best viewing angle
OPTION 2: FLUSH MOUNTING
1. Twist the front camera lens cover counter clockwise to remove it. Once the cover is remove,
slide the red O-Ring and the metal lip mount bracket off of the camera and then slide the
supplied alternate metal flush mounting bracket and the O-ring back onto the camera.
2. Twist the alternate flush-mount camera lens cover clockwise onto the camera
3. Use the provided hole saw bit to drill the hole of the camera
4. Route the wire harness through the drilled hole and into the vehicle.
5. Snap the camera into place and adjust to give the correct viewing angle
OPTION 2: FLUSH MOUNT
OPTION 1: LIP MOUNT
Mounting
Bracket
REMOVE RED O-RING
REMOVE LIP MOUNT
BRACKET
ATTACH ALTERNATE
FLUSH MOUNT BRACKET &
REPLACE RED O-RING
ATTACH ALTERNATE
FLUSH MOUNT LENS
COVER
Cable
Bracket
Screw
Mounting
Surface
DOUBLE SIDE TAPE
NOTE:
REMOVE LENS COVER
Mounting
Surface
Camera Lens
3M
3M
3M
UNSCREW LENS COVER
3M
3M
3M
Cable
SIDE
VIEW
You can use either the double-side tape
or screws to mount the bracket
Camera
Lens
NOTE:
Mounting Clip
Use provided hole saw bit to drill the
hole for the camera to mount
REVERSE (MIRROR) IMAGING:
The SV-6922.LM Camera has built-in circuitry to “mirror” the image so objects on the right of vehicle
appear on the right and objects on the left appear on the left when looking at a standard monitor. If
your existing monitor or in-dash monitor has a reverse camera input where the monitor itself performs
the mirror image, then your picture will not be correct. If this happens, the SV-6922.LM camera has
wire that can be cut reverse the image back to normal. (See Wiring Diagram)
WIRING:
1. Carefully choose a hidden out-of-sight location (possibly behind the plate) for drilling the cable
hole. Some vehicles may have an existing hidden rubber grommet or plug available to avoid
having to drill into the body. Be sure to double-check for any wiring or obstructions behind the
surface where you are going to drill the cable hole.
2. Choose a convenient place to run the camera cable up the left, right or center of the vehicle. As
a rule of thumb, try to avoid main factory harness looms that may contain high levels or RF noise
or interference.
3. You can connect the camera power at the rear of the vehicle behind the reverse lights. You may
also connect power inside the vehicle under the dash or in the trunk. The Red power wire goes to
Reverse Light +12V, and the Black wire to Ground. The White wire that comes out of the side of
the harness is for reverse imaging. Keep the wire connected for normal image or cut the wire in
half for reverse image.
4. Run the Yellow RCA video cable to the monitor’s video input or reverse camera input.
Connect to +12V
Reverse Light
YELLOW RCA
Connect to
Monitor
Ground
BLACK
WIRE
RED WIRE
WHITE WIRE
Mirror Image Option
SV-6922.LM CAMERA
MONITOR
CAMERA:
1. The color CMOS camera is maintenance-free, waterproof (IP-68) and vibration resistant.
2. This camera is designed to work well in day time or night time conditions.
3. The camera is completely electronic. There are NO manual adjustments for focus, etc.
TECH SUPPORT: (800) 998-6880
SPECIFICATIONS:
1/4 Inch Color CMOS Sensor
Dimension (MM): CAM: 14(L) × 14(W) × 16(D)
BKT: 6(L) × 36(W) × 17(D)
Weight: 10 Oz.
Pixels: 656 (H) x 492 (V)
Resolution: > 250,000 pixels
420 TV lines
Minimum Illumination: 1 LUX / F 1.2
Lens Type: Wide Angle
Horizontal Angle: 170°
Vertical Angle: 120°
Video Output: 1.0 V P-P composite (75 Ohm load)
Supply Voltage: +12VDC
Power Consumption: 70mA
Electronic Shutter: 1/50 s – 1/100000s
White Balance: Automatic
Gamma Correction: 0.45
S/N Ratio: More than 48dB
Operating Temp: -13° to 185° F (-20° to 75° C)
Gain Control: Automatic
DISCLAIMER:
Under no circumstances shall the manufacturer or distributor of the Securview™ be held liable for
consequential or incidental damages sustained in connection with the use of the Securview™ Rear
Vision System. The Securview™ is designed as a safety enhancement device and is in no way intended
as a replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when
backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are
closer than they appear. For the best fit, modification of the vehicle license may or may not be
necessary. It is the sole responsibility of the vehicle owner to check and verify any and all State or
Federal Motor vehicle codes with regards to modifications of vehicle license plates. The manufacturer of
the Securview™ assumes no liability or responsibility whatsoever with regards modifications of the
license plate.
www.crimestopper.com
email@crimestopper.com
Phone (800) 998-6880
FAX (805) 581-9500
© 2011 Crimestopper Security Products
4-6-2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising