2 Safety Information

Add to my manuals
42 Pages

advertisement

2 Safety Information | Manualzz

Contents

1 Introduction

1.1

1.1.1

1.2

1.3

Welcome .......................................................................................................................................... 1-2

Configuration and Usage of this Guide.............................................................................................. 1-2

Environmental Information............................................................................................................. 1-3

Legal Restrictions on Reproduction ............................................................................................. 1-4

2 Safety Information

2.1.8

2.1.9

2.2

2.2.1

2.2.2

2.2.3

2.3

2.3.1

2.1

2.1.1

2.1.2

2.1.3

2.1.4

2.1.5

2.1.6

2.1.7

2.3.2

2.3.3

2.3.4

2.3.5

2.3.6

2.3.7

2.3.8

2.3.9

2.3.10

2.3.11

2.3.12

2.3.13

2.3.14

2.3.15

2.3.16

2.4

2.4.1

2.4.2

2.4.3

2.4.4

2.4.5

2.4.6

2.4.7

2.4.8

Warnings and Precautions ............................................................................................................. 2-3

Power Source Connection ................................................................................................................. 2-3

Installation.......................................................................................................................................... 2-4

Using the Product .............................................................................................................................. 2-5

Consumables ..................................................................................................................................... 2-6

Glue Pellet.......................................................................................................................................... 2-7

Perfect Binder .................................................................................................................................... 2-7

Image Controller IC-313..................................................................................................................... 2-8

Image Controller IC-417/Image Controller IC-313............................................................................. 2-8

Image Controller IC-314..................................................................................................................... 2-8

Regulation Notices.......................................................................................................................... 2-9

Laser Safety ....................................................................................................................................... 2-9

Ozone Release ................................................................................................................................. 2-10

Electromagnetic Interference and Safety Approvals ....................................................................... 2-10

Warning and Caution Labels........................................................................................................ 2-12

Caution Labels on Fusing Part of Conveyance Fixing Unit ............................................................. 2-12

Warning Label on Waste Toner Box ................................................................................................ 2-13

Warning and Caution Labels on Saddle Stitcher SD-513................................................................ 2-14

Caution Label on Perfect Binder PB-503......................................................................................... 2-18

Caution Labels on Finisher FS-532.................................................................................................. 2-19

Caution Labels on Output Tray OT-510........................................................................................... 2-21

Caution Label on Finisher FS-531/Finisher FS-612......................................................................... 2-22

Caution Label on Finisher FS-531, Finisher FS-612, Finisher FS-532, or Output Tray OT-510

Connected .......................................................................................................................................2-23

Caution Label on Output Tray OT-511 Connected.......................................................................... 2-24

Caution Labels on Large Capacity Unit LU-202m ........................................................................... 2-25

Caution Labels on Large Capacity Unit LU-202XL.......................................................................... 2-26

Warning Labels for Current Leakage and Grounding on the Back of the Main Body ..................... 2-27

Warning Label on Paper Feeder Unit PF-602m Connected with Dehumidifier Heater HT-504 ...... 2-28

Warning Label on Large Capacity Unit LU-202m / Large Capacity Unit LU-202XL Connected with

Dehumidifier Heater HT-514 ............................................................................................................2-28

Warning Labels on Multi Punch GP-501.......................................................................................... 2-29

Caution and Warning Labels on Auto Ring Binder GP-502............................................................. 2-30

Operation Precautions.................................................................................................................. 2-32

Power Source .................................................................................................................................. 2-32

Operating Environment .................................................................................................................... 2-32

Storage of Printed Materials ............................................................................................................ 2-32

Ozone Release ................................................................................................................................. 2-32

Direct Sunlight.................................................................................................................................. 2-32

Authentication Unit AU-201S........................................................................................................... 2-32

Data Stored in This Machine............................................................................................................ 2-32

Precaution for Use of Folding Unit, Finisher and Output Tray......................................................... 2-33

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L Contents-1

Contents-2 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

1

Introduction

1 Welcome 1.1

1 Introduction

1.1

1.1.1

Welcome

Thank you for purchasing this machine.

This User’s Guide provides precautions and requests that should be followed to ensure safe usage of this machine. Please be sure to read this guide before using the machine.

Please keep this manual in a safe place where you can access them easily.

Configuration and Usage of this Guide

There are two types of User's Guides for this machine: booklet manuals and User's Guide CD.

When you want to learn about detailed functions or operation procedures, refer to the HTML User's Guide included in the User's Guide CD.

Title of booklet manual

[Quick Guide]

[Safety Information] (This Guide)

Overview

This guide describes the basic operations of the machine, how to install the printer driver and applications, and how to replace consumables.

This guide provides precautions and requests that should be followed to ensure safe usage of this machine.

Read this guide before using the machine.

Title of manual in User's Guide CD

HTML User's Guide

Overview

This guide describes basic operations, functions that enable more convenient operations, how to carry out maintenance, simple troubleshooting, and various settings of this machine.

Note that basic technical knowledge about the machine is required to enable users to perform maintenance work or troubleshooting operations. Maintenance and troubleshooting operations should be carried out as instructed in this guide and the HTML User's Guide included in the User's Guide CD.

Should you experience any problems, contact your service representative.

1-2 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

1.2

1.2

Environmental Information

Environmental Information

Energy Star

®

1

The ENERGY STAR® Program has been established to encourage the widespread and voluntary use of energy efficient technologies that reduce energy consumption and prevent pollution. As an ENERGY STAR Partner, this product meets the ENERGY STAR guidelines for energy efficiency, based on the following features.

Auto Low Power

Auto Low Power conserves energy by lowering the power consumption. The time period to activate this function can be set for --- minute, 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, 120 minutes, or 240 minutes. Power saving time periods, 90, 120, and 240 minutes, may not be displayed depending on regions.

As default of Auto Low Power, [--- min.] is specified. Setting [--- min.] for Auto Low Power means that Auto

Low Power is disabled.

Setting [--- min.] (OFF) for Auto Shut Off automatically changes the Auto Low Power setting to [5 min.] Setting change for Auto Low Power, however, can be made as desired.

When any option other than [--- min.] (OFF) is specified for Auto Shut Off, the time period for Auto Low Power cannot exceed that for Auto Shut Off.

Auto Shut Off

Auto Shut Off achieves further energy conservation by reducing power consumption. The time period to activate this function can be set for --- minute, 0 minute, 1 minute, 30 minutes, 60 minutes, 90 minutes, 120 minutes, or 240 minutes.

As default of Auto Shut Off, [1 min.] is specified. The touch panel display and LEDs other than the Power Save and Power LEDs turn off lowering power consumption of the machine.

Setting [--- min.] for Auto Shut Off means that Auto Shut Off is disabled.

The time period for Auto Shut Off cannot be shorter than that for Auto Low Power.

ErP Setting

This is a function that turns the main power switch OFF when a certain period of time elapses with Auto Low

Power activated, Auto Shut Off activated, or the sub power switch turned OFF.

The time period to activate this function can be set for none (Do Not Switch), 12 hours, 24 hours, 36 hours,

48 hours, 60 hours, or 72 hours.

If the Weekly Timer ON/OFF Setting is set to [Weekly Timer ON], the [02 ErP Setting] key will be grayed out to show inactivity.

Automatic Duplex Printing

To reduce paper consumption, use this function for double-sided (duplex) printing automatically.

Combine

To reduce paper consumption, use this function to print a fixed number (2, 4, or 8) of original pages onto one sheet of paper.

We recommend that you utilize the Auto Low Power, Auto Shut Off, ErP Setting, Automatic Duplex Printing, and Combine functions.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 1-3

1

1.3

Legal Restrictions on Reproduction 1.3

Legal Restrictions on Reproduction

Certain types of originals must never be reproduced with the purpose or intent to pass reproductions of such originals off as the originals.

The following is not a complete list, but is meant to be used as a guide to responsible reproduction.

-

-

-

-

<Financial Instruments>

-

-

Personal checks

Traveler’s checks

Money orders

Certificates of deposit

Bonds or other certificates of indebtedness

Stock certificates

-

-

-

-

-

-

<Legal Originals>

-

-

Food stamps

Postage stamps (canceled or uncanceled)

Checks or drafts drawn by government agencies

Internal revenue stamps (canceled or uncanceled)

Passports

Immigration papers

Motor vehicle licenses and titles

House and property titles and deeds

<General>

-

-

Identification cards, badges, or insignias

Copyrighted works without permission of the copyright

In addition, it is prohibited under any circumstances to reproduce domestic or foreign currencies, or works of art without permission of the copyright owner.

When in doubt about the nature of an original, consult with legal counsel.

NOTICE

This machine provides the forgery prevention function in order to prevent financial instruments from being reproduced illegally.

We appreciate your understanding that printed images may infrequently have some noise or image data may not be stored under certain circumstances due to this forgery prevention function.

1-4 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2

Safety Information

2

2 Safety Information

This section contains detailed instructions on the operation and maintenance of this machine. To achieve optimum utility of this device, all operators should carefully read and follow the instructions in this manual.

Please read the following section before connecting the machine to the supply. It contains important information related to user safety and preventing equipment problems.

Make sure that you observe all of the precautions that appear in different sections of this manual.

KMI_Ver. 02_E d

Reference

Some parts of the contents of this section may not correspond with the purchased product.

Warning and precaution symbols

Be sure to observe the safety precautions.

This manual contains the instructions that should be strictly observed at all times to prevent injury to yourself and other persons as well as damage to property.

Injuries and damage that might be caused by using the product improperly are classified according to the following symbols.

Pictorial indication Description

Improper handling can cause serious injury or death.

Improper handling can cause minor injury or damage to houses and property.

These are some of major exemplary graphical symbols.

Graphic symbols

Description Graphic symbols

Description

General

Prohibited

Do not disassemble

Graphic symbols

Description

Do not touch

Instructions Ground/Earth

General precaution

High temperature

Unplug from outlet

Electrical shock hazard

2-2 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.1

2.1

Warnings and Precautions

Warnings and Precautions

2.1.1

Power Source Connection

Do not use any power cord other than the one supplied in the package or attached on the products. If a power cord is not supplied, use only the power cord and plug that are specified in the user documentation. Failure to use this cord could result in a fire or electrical shock. If the power cord supplied in the package cannot be used in the country where this product was sold, use a power cord that meets the following conditions or contact your Technical Representative.

• The power cord has voltage and current rating appropriate for the rating plate on this machine.

• The power cord meets regulatory requirements for the area.

• The power cord is provided with grounding pin/terminal.

Do not use the power cord to other products.

Failure to do that could result in a fire or electrical shock.

Do not scratch, abrade, place a heavy object on, heat, twist, bend, step on, pull on, or damage the power cord. Use of a damaged power cord (exposed core wire, broken wire, etc.) could result in a fire or breakdown.

Should any of these conditions be found, immediately turn

OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative.

Do not use the power source voltage other than being specified on the machine. Failure to do that could result in a fire or electrical shock.

Do not use a multiple outlet adapter to connect any other appliances or machines. Use of a power outlet for more than the marked current value could result in a fire or electrical shock.

Do not use an extension cord. Use of an extension cord could cause a fire or electric shock. If the power cord furnished with the product is not long enough to be plugged into a wall outlet, contact your Technical Representative.

Do not unplug and plug in the power cord with a wet hand, as an electrical shock could result.

Plug the power cord all the way into the power outlet. Failure to do this could result in a fire or electrical shock.

Make sure to ground this product.(Connect the power cord to an electrical outlet that is equipped with a grounding terminal.) Failure to do so and an unlikely event of leakage could result in a fire or electrical shock.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2

2-3

2

The outlet must be near the equipment and easily accessible.

Otherwise you can not pull out the power plug when an emergency occurs.

Do not place any objects around the power plug, as the power plug may be difficult to pull out when an emergency occurs.

Do not tug the power cord when unplugging. Pulling on the power cord could damage the cord, resulting in a fire or electrical shock.

Remove the power plug from the outlet more than one time a year and clean the area between the plug terminals. Dust that accumulates between the plug terminals may cause a fire.

2.1.2

Installation

Keep this bag away from babies and children. Do not use in cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth and prevent breathing. This bag is not a toy.

Warnings and Precautions 2.1

Do not place a flower vase or other container that contains water, or metal clips or other small metallic objects on this product. Spilled water or metallic objects dropped inside the product could result in a fire, electrical shock, or breakdown.

Should a piece of metal, water, or any other similar foreign matter get inside the product, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your Technical Representative or your authorized service representative.

Make sure that the power cord is placed on a site in which no person would step on or trip over it. Stepping on or tripping over the power cord could heat the power cord, resulting in a fire or electric shock.

2-4

<If instructed to use fixing legs>

When the product has been installed, fix the product using the fixing legs. Not using the fixing legs could cause the product to move or topple over.

Do not place the product in a dusty place, or a site exposed to soot or steam, near a kitchen table, bath, or a humidifier.

A fire, electrical shock, or breakdown could result.

Do not place this product on an unstable or tilted bench, or in a location subject to a lot of vibration and shock. It could drop or fall, causing personal injury or mechanical breakdown.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.1

Warnings and Precautions

Do not let any object plug the ventilation holes of this product. Heat could accumulate inside the product, resulting in a fire or malfunction.

Whenever moving this product, be sure to disconnect the power cord and other cables. Failure to do this could damage the cord or cable, resulting in a fire, electrical shock, or breakdown.

When moving this product, always hold it at the locations specified in the User’s Guide or other documents. If the unit is moved while held at locations other than those specified, it may fall, causing severe personal injury.

2.1.3

Using the Product

Do not modify this product, as a fire, electrical shock, or breakdown could result. If the product employs a laser, the laser beam source could cause blindness.

Do not attempt to remove the covers and panels which have been fixed to the product. Some products have a high-voltage part or a laser beam source inside that could cause an electrical shock or blindness.

Do not keep using this product, if this product becomes inordinately hot or emits smoke, or unusual odor or noise. Immediately turn OFF the pow-er switch, unplug the power cord from the power outlet, and then call your Technical Representative or your authorized service representative. If you keep on using it as is, a fire or electrical shock could result.

Do not keep using this product, if this product has been dropped or its cover damaged. Immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your Technical Representative or your authorized service representative. If you keep on using it as is, a fire or electrical shock could result.

Do not use flammable sprays, liquids, or gases inside or near this machine. Do not clean the inside of this machine using a flammable gas duster. A fire or explosion could result.

<If an RFID module (limited only to 13.56 MHz) for use in inside-the-machine proximity communication or electromagnetic induction heating (IH) technology (limited only to 20.05 kHz to 100 kHz) is being used>

This machine generates a weak magnetic field. If you experience any unusual symptoms with your implantable medical equipment (cardiac pacemaker, etc.) while near the machine, move away from the machine and see a doctor immediately.

Please call your Technical Representative or your authorized service representative if you do not understand the purchased product corresponds or not.

<If a non-contact IC card reader is being used>

If you use an implantable medical equipment (cardiac pacemaker, etc.), do not bring the IC card reader close from the implant within 12 cm at all times. The radio waves may affect implantable medical equipment (cardiac pacemaker, etc.) operations.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2

2-5

2 Warnings and Precautions 2.1

Using this product in a poorly ventilated room for a long time or producing a large volume of copies or prints may cause the odor of exhaust air from the machine. Ventilate the room well.

The inside of this product has areas subject to high temperature, which may cause burns.When checking the inside of the unit for malfunctions such as a paper misfeed, do not touch the locations (around the fusing unit, etc.) which are indicated by a "Caution HOT" caution label. A burn could result.

Unplug the product when you will not use the product for long periods of time.

When using the machine, do not look at the light of the lamp for a prolonged time. Eyestrain could result.

Do not use stapled paper, conductive paper (such as silver paper or carbon paper) or treated heat-sensitive/inkjet paper, otherwise a fire may result.

2.1.4

Consumables

2-6

Do not throw toner or a container that contains toner (e.g., toner cartridge and developing unit) into an open flame. The hot toner may scatter and cause burns or other damage.

Do not leave toner-related parts (e.g., toner cartridge and developing unit) within easy reach of children. Licking any of these parts or ingesting toner could damage your health.

Do not store toner-related parts (e.g., toner cartridge and developing unit) near devices susceptible to magnetism, such as precision equipment and data storage devices, otherwise they may malfunction. They could cause these products to malfunction.

Do not force open the toner-related parts (e.g., toner cartridge and developing unit). If toner tumbles from the toner bottle, take utmost care to avoid inhaling it or even getting skin contact.

If toner lands on your skin or clothing, wash thoroughly with soap and water.

If you inhale toner, move to a place with fresh air and gargle with a lot of water repeatedly. Should you get symptoms such as coughing, seek medical advice.

If you get toner into your eyes, immediately rinse them with running water for over 15 minutes. Seek medical advice if irritation persists.

If you swallow toner, rinse out your mouth and drink a few glasses of water. Seek medical advice if necessary.

Never touch the electrical contacts of the units (e.g., toner cartridge and developing unit), as an electrostatic discharge may damage the product.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.1

Warnings and Precautions

Before handling, see the user documentation for the safety information.

<If instructed to replace the fusing unit>

The fusing section is extremely hot. Before replacing the fusing unit, be sure to open doors and covers of the machine.

Then, leave the machine to stand idle for a specified period of time and make sure that the fusing section has cooled down to room temperature. Failure to follow these instructions could result in a burn.

2.1.5

Glue Pellet

Do not put glue pellets close to fire. Glue pellets are flammable and easy to catch on fire.

Do not swallow glue pellets. Should you swallow any, drink large amount of water or milk to vomit, and immediately consult a doctor.

Keep out of reach of children in order to avoid unexpected accidents.

2.1.6

Perfect Binder

Do not use the perfect binder without ventilation for an extended period of time. Ensure to ventilate the room on a regular basis. It is recommended that the perfect binder should be installed in a place with a local exhaust system. Using the perfect binder in a room without appropriate ventilation could pose health hazard.

Handle melted hot glue carefully. If it gets in the eye, do not rub nor tray to open the eye, but cool it with cold water immediately and consult a doctor.

Do not touch melted hot glue as it may cause burn injury. If it sticks on your skin, cool that part of the skin with cold water immediately and consult a doctor.

Do not touch the glue tank unit immediately after you turned off the machine to avoid burn injury. Wait until the unit is no longer hot when you handle it directly with your hands.

Do not put the glue hopper and the glue tank unit close to fire.

Glue is flammable and easy to catch on fire.

Do not get close to the vapor emitted from melted hot glue.

If you have irritation in or around your eyes, nose or throat, move to an area where you can get fresh air.

Do not block up the vent for the fan on the back of the perfect binder. This will prevent the discharge of heat, and may cause fire or breakdown.

Do not change the temperature setting for the glue tank unit.

This may cause fire or breakdown.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2

2-7

2

2.1.7

Image Controller IC-313

Never lift the Image Controller IC-313 by grasping the top panel. The top panel does not support the weight of the system.

The Image Controller IC-313 touch panel is a liquid crystal display (LCD) that is made of glass and can break. Do not subject it to strong shocks. If the Image Controller IC-313 touch panel breaks and the liquid crystal material leaks out, do not inhale, ingest, or touch it. If the material gets on your skin or clothing, wash it off with soap and water immediately.

Do not apply excessive pressure to the panel. This changes the color of the panel.

2.1.8

Image Controller IC-417/Image Controller IC-313

Do not attempt to disassemble or modify the Image Control-

ler IC-417 or Image Controller IC-313. This may result in a fire or electrical shock.

Do not keep using the Image Controller IC-417 or Image

Controller IC-313 if the Image Controller IC-417 or Image

Controller IC-313 becomes inordinately hot, emits smoke, unusual odor, or noise. Immediately turn off the power switch, unplug the power cord from the power outlet, and call your authorized service representative.

2.1.9

Image Controller IC-314

The Image Controller IC-314 is heavy, and must be lifted by two people.

Each person must place both hands underneath the Image

Controller IC-314 from the sides.

Lift up the Image Controller IC-314 using the handle and not using the front panel. Lifting it up using the front panel may result in major injury.

Before opening the Image Controller IC-314 covers, ensure that the unit has been switched off. Switching off only the

ON/OFF power button will leave some circuits energized. For complete disconnection from the supply, the main power cable must also be disconnected from the power source.

Do not attempt to disassemble or modify the Image Control-

ler IC-314. This may result in a fire or electrical shock.

Do not keep using the Image Controller IC-314 if the Image

Controller IC-314 becomes inordinately hot, emits smoke, unusual odor, or noise. Immediately turn off the power switch, unplug the power cord from the power outlet, and call your authorized service representative.

Warnings and Precautions 2.1

2-8 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.2

2.2

Regulation Notices

Regulation Notices

2.2.1

2

Laser Safety

This product employs a Class 3B laser diode having maximum power of 15 mW and wavelength of 787-800 nm.

This product is certified as a Class 1 laser product. Since the laser beam is concealed by protective housings, the product does not emit hazardous laser radiation as long as the product is operated according to the instructions in this manual.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-9

2

2.2.2

2.2.3

Regulation Notices 2.2

Ozone Release

During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely. However, be sure the room where the machine is being used has adequate ventilation, especially if you are printing a high volume of materials, or if the machine is being used continuously over a long period.

Electromagnetic Interference and Safety Approvals

This product must be used with a shielded network cable and shielded USB cable.

The length of USB cable must be 3 meters or less.

The use of such cables is likely to result in interference with radio communications.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

For European Users

CE Marking (Declaration of Conformity) for users of the European Union (EU) Declaration of Conformity is available at " http://www.konicaminolta.eu/".

This product complies with IEC61000-3-12.

This product is GS-certified for the Konica Minolta branded model AccurioPress C2070, C2070P, C2060 and

AccurioPrint C2060L.

The product, PF-602m is GS-certified for the Konica Minolta branded model PF-602.

For German Users

Der Höchste Schalldruckpegel beträegt 85 dB(A) oder weniger nach ISO

7779.

This device is not intended for use in the direct field of view at visual display workplaces.

To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view.

For U.S.A and Canada Users

This product is cTUVus-certified for the Konica Minolta branded model AccurioPress C2070, C2070P, C2060 and AccurioPrint C2060L.

The product, PF-602m is cTUVus-certified for the Konica Minolta branded model PF-602.

Notification for California Customers

This product uses a CR Lithium Battery which contains perchlorate material.

This perchlorate warning applies to perchlorate-containing lithium batteries sold or distributed in California,

USA.

"Perchlorate Material - Special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate."

USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY DEVICES (For U.S.A. Users)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING:

The design and production of this unit conform to FCC regulations, and any changes or modifications must be registered with the FCC and are subject to FCC control. Any changes made by the purchaser or user without first contacting the manufacturer will be subject to penalty under FCC regulations.

2-10 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.2

Regulation Notices 2

This device must be used with a shielded network cable and a shielded USB cable. The use of non-shielded cables is likely to result in interference with radio communications and is prohibited under FCC rules.

INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 5) (For Canada Users)

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

For EU member states only

This symbol means: Do not dispose of this product together with your household waste!

Please refer to the information of your local community or contact our dealers regrading the proper handling of end-of-life electric and electronic equipments. Recycling of this product will help to conserve natural resources and prevent potential negative consequences for the environment and human health caused by inappropriate waste handling.

Graphic symbols used on this machine

These are some of major exemplary graphical symbols.

Graphic symbols

Descriptions Graphic symbols

Descriptions

"ON" position “OFF” position

Graphic symbols

Descriptions

STAND-BY push-push type switches

CLASS II

EQUIPMENT

General precaution

CAUTION moving fan blade

Ground/Earth

(Protective bonding terminal)

Class II equipment with functional earthing

High temperature

CAUTION

DOUBLE

POLE /

NEUTRAL

FUSING

Ground/Earth

(Protective earthing)

Functional earthing

Electrical shock hazard

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-11

2

2.3

Warning and Caution Labels 2.3

Warning and Caution Labels

This machine has warning label, caution labels and indicators for safety precaution in the following location.

These labels and indicators advise you to pay special attention to avoid any dangerous situations or serious injury when you replace the units.

7 CAUTION

DO NOT remove warning or caution labels!

Should any warning or caution label be removed, you may fail to check a specific part to be alert for unexpected trouble or injury. If you find any warning or caution label removed or illegible due to soilage, please contact your service representative.

2.3.1

Caution Labels on Fusing Part of Conveyance Fixing Unit

7 CAUTION

DO NOT touch the fusing part of the conveyance fixing unit. Otherwise, you may get burned.

Please be especially careful in withdrawing the conveyance fixing unit or opening the fusing part.

2-12 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

2.3.2

Warning and Caution Labels

Warning Label on Waste Toner Box

7 WARNING

NEVER throw the waste toner box into a fire.

Otherwise, the toner may ignite and cause a dangerous situation.

2

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-13

2

2.3.3

Warning and Caution Labels

Warning and Caution Labels on Saddle Stitcher SD-513

2.3

7 WARNING

When taking out output sheets from the bundle exit tray, do not put your hand into the shutter of the outlet.

If you put your hand into the shutter while sheets are being delivered onto the bundle exit tray, it may cause an unexpected accident.

Before removing out output sheets, make sure that they have all been delivered onto the bundle exit tray.

2-14 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

Warning and Caution Labels

7 CAUTION

When closing the clamp section, do not put your hand between the clamp section and the main body.

Your hand is caught between them, it may cause an unexpected accident.

Be careful to close the clamp section.

2

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-15

2 Warning and Caution Labels 2.3

7 CAUTION

When the clamp section is opened, the internal unit inside the saddle stitcher may be located forward. Do not touch the motor section of the internal unit with your hand.

The motor section of the internal unit may be hot. If you touch it with your hand, you may burn your hand.

Pay special attention to clear jammed paper inside the main body of the saddle stitcher.

2-16 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

Warning and Caution Labels

7 WARNING

Before starting the service, disconnect the power cord.

Otherwise, it may cause an electric shock.

7 WARNING

Be sure to connect this product to an earthed socket outlet only.

Failure to do so and an unlikely event of leakage could result in a fire or electrical shock.

2

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-17

2

2.3.4

Warning and Caution Labels 2.3

Caution Label on Perfect Binder PB-503

7 CAUTION

DO NOT touch the glue tank unit. Otherwise, you may get burned.

Please be especially careful if you push the glue tank unit backward in place.

2-18 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

2.3.5

Warning and Caution Labels

Caution Labels on Finisher FS-532

2

7 CAUTION

DO NOT put your hand on the top of printed sheets when removing them from the primary (main) tray.

Failure to do so may cause unexpected injury, such as getting your fingers squeezed between the main body and the primary (main) tray going upward. Be sure to hold both front and rear sides of the stack to remove it from the tray.

7 CAUTION

DO NOT insert your fingers into the space between the main body and the primary (main) tray.

Failure to do so may cause unexpected injury, such as getting your fingers squeezed by the primary

(main) tray sliding sideways. Please be careful when removing paper from the tray.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-19

2 Warning and Caution Labels 2.3

7 CAUTION

DO NOT put your hand into the hollow portion inside the finisher.

The finisher mounted with Punch Kit PK-522 has a hollow portion, in the back of which is located a motor. Touching the motor, you may get burned. Please do not put your hand deep into the hollow portion when removing mishandled paper.

2-20 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

2.3.6

Warning and Caution Labels

Caution Labels on Output Tray OT-510

2

7 CAUTION

DO NOT put your hand on the top of printed sheets when removing them from the primary (main) tray.

Failure to do so may cause unexpected injury, such as getting your fingers squeezed between the main body and the primary (main) tray going upward. Be sure to hold both front and rear sides of the stack to remove it from the tray.

7 CAUTION

DO NOT insert your fingers into the space between the main body and the primary (main) tray.

Failure to do so may cause unexpected injury, such as getting your fingers squeezed by the primary

(main) tray sliding sideways. Please be careful when removing paper from the tray.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-21

2

2.3.7

Warning and Caution Labels

Caution Label on Finisher FS-531/Finisher FS-612

2.3

7 CAUTION

DO NOT put your hand on the top of printed sheets when removing them from the primary (main) tray.

Failure to do so may cause unexpected injury, such as getting your fingers squeezed between the main body and the primary (main) tray going upward. Be sure to hold both front and rear sides of paper when removing printed sheets from the tray.

2-22 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

2.3.8

Warning and Caution Labels 2

Caution Label on Finisher FS-531, Finisher FS-612, Finisher FS-532, or Output Tray OT-510 Connected

The caution label shown below is affixed when Finisher FS-531, Finisher FS-612, Finisher FS-532, or Out-

put Tray OT-510 is directly connected to the left side of the machine.

This caution label is not affixed when the finisher or output tray is connected while the Relay Unit RU-509 is connected to the left side of the machine.

7 CAUTION

DO NOT touch the roller in the left side of the machine or surrounding metal parts.

Otherwise, you may get burned. Please be especially careful in pressing down a lever or clearing jammed paper.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-23

2

2.3.9

Caution Label on Output Tray OT-511 Connected

Warning and Caution Labels

7 CAUTION

DO NOT touch the roller in the left side of the machine or surrounding metal parts.

Otherwise, you may get burned. Please be especially careful in pressing down a lever or clearing jammed paper.

2.3

2-24 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

Warning and Caution Labels

2.3.10

Caution Labels on Large Capacity Unit LU-202m

2

7 CAUTION

DO NOT put your hand into the three holes on the tray bottom plate.

Failure to do so may cause unexpected injury, such as getting your hand squeezed. Be especially careful when loading paper.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-25

2

2.3.11

Caution Labels on Large Capacity Unit LU-202XL

Warning and Caution Labels 2.3

7 CAUTION

DO NOT put your hand into the five holes on the tray bottom plate.

Failure to do so may cause unexpected injury, such as getting your hand squeezed. Be especially careful when loading paper.

2-26 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

Warning and Caution Labels 2

2.3.12

Warning Labels for Current Leakage and Grounding on the Back of the Main

Body

7 WARNING

Make sure that this product is correctly grounded.

Before unplugging the main body, unplug all power plugs of optional devices.

Since a large amount of current leaks, make sure to connect the power plug into a power outlet that is grounded.

7 WARNING

Make sure that this product is correctly grounded.

Otherwise an electrical shock may result. Make sure to connect the power plug into a power outlet that is grounded.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-27

2 Warning and Caution Labels 2.3

2.3.13

Warning Label on Paper Feeder Unit PF-602m Connected with Dehumidifier

Heater HT-504

The caution label shown below is affixed when Dehumidifier Heater HT-504 is connected to Paper Feeder

Unit PF-602m.

7 WARNING

Be sure to connect this product to an earthed socket outlet only.

Failure to do so and an unlikely event of leakage could result in a fire or electrical shock.

2.3.14

Warning Label on Large Capacity Unit LU-202m / Large Capacity Unit LU-

202XL Connected with Dehumidifier Heater HT-514

The caution label shown below is affixed when Dehumidifier Heater HT-514 is connected to Large Capac-

ity Unit LU-202m or Large Capacity Unit LU-202XL.

Dehumidifier Heater HT-514 is an optional device that is only available in Australia.

7 WARNING

Be sure to connect this product to an earthed socket outlet only.

Failure to do so and an unlikely event of leakage could result in a fire or electrical shock.

2-28 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

Warning and Caution Labels

2.3.15

Warning Labels on Multi Punch GP-501

2

7 WARNING

This safety message means you could get an electrical shock because disconnecting power from this section does not cut off power from adjacent sections of the machine.

7 WARNING

This safety message means that you might get seriously hurt or killed if you open the product and expose yourself to hazardous voltage. NEVER remove the screws on covers. ALWAYS refer service requirements to qualified service personnel.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-29

2 Warning and Caution Labels

2.3.16

Caution and Warning Labels on Auto Ring Binder GP-502

2.3

7 CAUTION

NEVER put your hand on the display panel when closing the upper part of the auto ring binder!

Otherwise, you may be injured. Please be careful when closing the upper part of the auto ring binder.

7 CAUTION

When the top cover or bypass deck of the ring binder is opened, be careful of your head.

Otherwise, you may be injured getting bumped on your head. Please be especially careful when removing mishandled paper.

2-30 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.3

Warning and Caution Labels 2

7 WARNING

This safety message means you could get an electrical shock because disconnecting power from this section does not cut off power from adjacent sections of the machine.

7 WARNING

This safety message means that you might get seriously hurt or killed if you open the product and expose yourself to hazardous voltage. NEVER remove the screws on covers. ALWAYS refer service requirements to qualified service personnel.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-31

2

2.4

2.4.1

2.4.2

2.4.3

2.4.4

2.4.5

2.4.6

2.4.7

Operation Precautions

Operation Precautions

To ensure the optimum performance of this machine, observe the precautions described below.

2.4

Power Source

The power source requirements are as follows.

Destination North America

Voltage

Frequency

208 V to 240 V AC

60 Hz

Europe, Southeast

Asia, Australia

220 V to 240 V AC

50-60 Hz

Use a power source with as little voltage or frequency fluctuations as possible.

Operating Environment

The environmental requirements for correct operation of the machine are as follows.

Operating temperature: 10°C (50°F) to 30°C (86°F)

Humidity: 10% to 80%

Storage of Printed Materials

To store printed materials, follow the recommendation listed below.

Printed materials that are to be kept for a long time should be stored where they are not exposed to light or high temperature in order to prevent them from fading or sticking together.

Adhesive that contains solvent (e.g., spray glue) may dissolve the toner on printed materials.

Ozone Release

During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely. However, be sure the room where the machine is being used has adequate ventilation, especially if you are printing a high volume of materials, or if the machine is being used continuously over a long period.

Direct Sunlight

Do not install the machine and its options in a place exposed to direct sunlight, otherwise the machine performance may be degraded or any trouble may be caused.

Authentication Unit AU-201S

Do not use this product near water, otherwise it may be damaged.

Do not cut, damage, modify or forcefully bend the USB cable. A malfunction may occur as a result of a damaged or cut USB cable.

Do not diassembly this device, otherwise it may be damaged.

Do not store the IC card within 40 mm of the card scanning area.

Data Stored in This Machine

For the machine with hard disk, it is suggested to perform the [Delete All Data Setting] function to prevent leakage of data prior to transfer or disposal of the machine, or returning of the leased machine.

Using the [Delete All Data Setting] function, all data stored in all hard disk areas are overwritten and deleted.

Contact your service representative before using the [Delete All Data Setting] function.

It is recommended to backup HDD periodically as the measures for HDD defect. For the detail information of

HDD backup, contact your service representative.

2-32 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

2.4

2.4.8

Operation Precautions 2

Precaution for Use of Folding Unit, Finisher and Output Tray

The primary (main) tray of Folding Unit FD-503, Finisher FS-531, Finisher FS-532, Finisher FS-612, or of

Output Tray OT-510 gradually goes down while printed materials output. DO NOT allow any object to interfere with the operation of the tray on the left side of the finisher, as any interference may cause damage to the finisher or injury.

AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L 2-33

2 Operation Precautions 2.4

2-34 AccurioPress C2070/C2070P/C2060, AccurioPrint C2060L

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents