Quick Operation Guide of 0700/8800/8700 Series NVR

Quick Operation Guide of 0700/8800/8700 Series NVR
Quick Operation Guide of
0700/8800/8700 Series NVR
Quick Operation Guide of 0700/8800/8700 Series NVR
TABLE OF CONTENTS
NVR Pre-Installation ............................................................................................................................... 2
NVR Installation ...................................................................................................................................... 2
Hard Disk Installation ............................................................................................................................. 2
Front Panel ............................................................................................................................................... 5
Rear Panel............................................................................................................................................... 12
Peripheral Connections ......................................................................................................................... 15
Wiring of Alarm Input / Output ................................................................................................................ 15
Using of Alarm Connectors ...................................................................................................................... 15
Controller Connection .............................................................................................................................. 16
Specifications .......................................................................................................................................... 17
HDD Storage Calculation Chart ........................................................................................................... 24
Menu Operation ..................................................................................................................................... 25
Menu Structure......................................................................................................................................... 25
Startup and Shutdown .............................................................................................................................. 26
Using the Start Wizard ............................................................................................................................. 26
Live View ................................................................................................................................................. 31
Adding and Configuring IP Cameras ....................................................................................................... 31
Adding IP Cameras .......................................................................................................................... 31
Configuring Basic Parameters of IP Cameras .................................................................................. 32
PTZ Control ............................................................................................................................................. 33
PTZ Settings..................................................................................................................................... 34
PTZ Control ..................................................................................................................................... 34
Playback ................................................................................................................................................... 35
Instant playback by channel ............................................................................................................. 35
Playback by channel ......................................................................................................................... 35
Backup ..................................................................................................................................................... 36
Accessing by Web Browser .................................................................................................................... 38
Logging In................................................................................................................................................ 38
Live View ................................................................................................................................................. 38
Recording ................................................................................................................................................. 39
Playback ................................................................................................................................................... 40
Log
....................................................................................................................................................... 41
1
Quick Operation Guide of 0700/8800/8700 Series NVR
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
This manual is applicable to 8700, 8800 and 0700 series NVR.
NVR Pre-Installation
The 0700/8800/8700 series NVR are highly advanced surveillance equipment that should be installed with care.
Please take into consideration the following precautionary steps before installation of the NVR.
1. Keep all liquids away from the NVR.
2. Install the NVR in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory specifications.
4. Install a manufacturer recommended HDD.
NVR Installation
During the installation of the NVR:
1.
2.
3.
4.
5.
6.
7.
8.
Use brackets for rack mounting.
Ensure there is ample room for audio and video cables.
When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter.
Connect both the alarm and RS-485 cable.
Allow at least 2cm (~0.75-inch) of space between racks mounted devices.
Ensure the NVR is grounded.
Environmental temperature should be within the range of -10 ºC ~ 55 ºC, 14ºF ~ 131ºF.
Environmental humidity should be within the range of 10% ~ 90%.
Hard Disk Installation
Before you start:
Disconnect the power from the NVR before installing a hard disk drive (HDD). A factory recommended HDD
should be used for this installation.
Up to 8 SATA hard disks can be installed on your NVR.
Tools Required: Screwdriver.
Steps (for 0700):
1. Fasten the hard disk mounting handle to the hard disk with screws.
2. Insert the key and turn in clockwise direction to open the panel lock.
2
Quick Operation Guide of 0700/8800/8700 Series NVR
3. Press the buttons on the panel of two sides and open the front panel.
4. Insert the hard disk along the slot until it is placed into position.
5. Repeat the above steps to install other hard disks onto the NVR. After having finished the installation of all
hard disks, close the front panel and lock it with the key again.
3
Quick Operation Guide of 0700/8800/8700 Series NVR
Steps (for 8700 and 8800):
1.
2.
Remove the cover from the NVR by unfastening the screws on the rear and side panel.
Connect one end of the data cable to the motherboard of NVR and the other end to the HDD.
3. Connect the power cable to the HDD.
4. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
4
Quick Operation Guide of 0700/8800/8700 Series NVR
Front Panel
0700 Series
No.
Name
Function Description
ALARM
READY
Turns red when a sensor alarm is detected.
Ready LED is normally blue, indicating that the device is
functioning properly.
Turns blue when device is controlled by an IR remote.
STATUS
Turns red when controlled by a keyboard and purple when IR
remote and keyboard is used at the same time.
1
Status
HDD
Indicators
MODEM
TX/RX
Flashes red when data is being read from or written to HDD.
Reserved for future usage.
Flashes blue when network connection is functioning properly.
Guard LED turns blue when the device is in armed status; at this
time, an alarm is enabled when an event is detected.
GUARD
The LED turns off when the device is unarmed. The arm/disarm
status can be changed by pressing and holding on the ESC
button for more than 3 seconds in live view mode.
2
IR Receiver
Receiver for IR remote
3
DVD-R/W
Slot for DVD-R/W.
Switch to the corresponding channel in Live view or PTZ
Control mode.
Input numbers and characters in Edit mode.
4
Alphanumeric Buttons
Switch between different channels in Playback mode.
The light of the button is blue when the corresponding channel is
recording; it is red when the channel is in network transmission
status; it is pink when the channel is recording and transmitting.
5
USB Interfaces
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
Back to the previous menu.
ESC
6
Press for Arming/disarming the device in Live View mode.
Composite
Enter the Manual Record setting menu.
Keys
REC/SHOT
In PTZ control settings, press the button and then you can call a
PTZ preset by pressing Numeric button.
5
Quick Operation Guide of 0700/8800/8700 Series NVR
No.
Name
Function Description
It is also used to turn audio on/off in the Playback mode.
The button is used to enter the Playback mode.
PLAY/AUTO
It is also used to auto scan in the PTZ Control menu.
ZOOM+
Zoom in the PTZ camera in the PTZ Control setting.
Adjust focus in the PTZ Control menu.
A/FOCUS+
It is also used to switch between input methods (upper and
lowercase alphabet, symbols and numeric input).
Edit text fields. When editing text fields, it will also function as
a Backspace button to delete the character in front of the cursor.
On checkbox fields, pressing the button will tick the checkbox.
EDIT/IRIS+
In PTZ Control mode, the button adjusts the iris of the camera.
In Playback mode, it can be used to generate video clips for
backup.
Enter/exit the folder of USB device and eSATA HDD.
MAIN/SPOT/ZOO Switch between main and spot output.
M-
In PTZ Control mode, it can be used to zoom out the image.
Select all items on the list when used in a list field.
In PTZ Control mode, it will turn on/off PTZ light (if
F1/ LIGHT
applicable).
In Playback mode, it is used to switch between play and reverse
play.
Cycle through tab pages.
F2/ AUX
In synchronous playback mode, it is used to switch between
channels.
Press the button will help you return to the Main menu (after
successful login).
Press and hold the button for 5 seconds will turn off audible key
MENU/WIPER
beep.
In PTZ Control mode, the MENU/WIPER button will start wiper
(if applicable).
In Playback mode, it is used to show/hide the control interface.
Switch between single screen and multi-screen mode.
PREV/FOCUS-
In PTZ Control mode, it is used to adjust the focus in
conjunction with the A/FOCUS+ button.
Enter the PTZ Control mode.
PTZ/IRIS-
In the PTZ Control mode, it is used to adjust the iris of the PTZ
camera.
The DIRECTION buttons are used to navigate between different
fields and items in menus.
7
Control
Buttons
In the Playback mode, the Up and Down button is used to speed
DIRECTION
up and slow down recorded video. The Left and Right button
will select the next and previous record files.
In Live View mode, these buttons can be used to cycle through
channels.
6
Quick Operation Guide of 0700/8800/8700 Series NVR
No.
Name
Function Description
In PTZ control mode, it can control the movement of the PTZ
camera.
The ENTER button is used to confirm selection in any of the
menu modes.
It can also be used to tick checkbox fields.
ENTER
In Playback mode, it can be used to play or pause the video.
In single-frame Playback mode, pressing the button will advance
the video by a single frame.
In Auto-switch mode, it can be used to stop /start auto switch.
Move the active selection in a menu. It will move the selection
up and down.
In Live View mode, it can be used to cycle through different
channels.
8
JOG SHUTTLE Control
In the Playback mode: For 0700-R series, the ring is used to
jump 30s forward/backward in video files.
In PTZ control mode, it can control the movement of the PTZ
camera.
9
POWER ON/OFF
Power on/off switch.
7
Quick Operation Guide of 0700/8800/8700 Series NVR
8800 Series
No.
Name
Function Description
POWER
Turns green when NVR is powered up.
READY
The LED is green when the device is running normally.
The light is green when the IR remote control is enabled;
1
Status
STATUS
Indicators
The light is red when the function of the composite keys (SHIFT)
are used;
The light is out when none of the above condition is met.
ALARM
2
The light is red when there is an alarm occurring.
HDD
Blinks red when HDD is reading/writing.
Tx/Rx
Blinks green when network connection is functioning normally.
DVD-R/W
Slot for DVD-R/W.
In menu mode, the direction buttons are used to navigate between
different fields and items and select setting parameters.
In playback mode, the Up and Down buttons are used to speed up
DIRECTION
and slow down record playing, and the Left and Right buttons are
used to move the recording 30s forwards or backwards.
In the image setting interface, the up and down button can adjust
3
the level bar of the image parameters.
Control
In live view mode, these buttons can be used to switch channels.
Buttons
The Enter button is used to confirm selection in menu mode; or
used to check checkbox fields and ON/OFF switch.
In playback mode, it can be used to play or pause the video.
ENTER
In single-frame play mode, pressing the Enter button will play the
video by a single frame.
In auto sequence view mode, the buttons can be used to pause or
resume auto sequence.
Switch between the numeric or letter input and functions of the
SHIFT
composite keys. (Input letter or numbers when the light is out;
Realize functions when the light is red.)
4
Composite
Keys
1/MENU
Enter numeral “1”;
Access the main menu interface.
2/ABC/F1
Enter numeral “2”;
Enter letters “ABC”;
8
Quick Operation Guide of 0700/8800/8700 Series NVR
No.
Name
Function Description
The F1 button when used in a list field will select all items in the
list.
In PTZ Control mode, it will turn on/off PTZ light and when the
image is zoomed in, the key is used to zoom out.
Enter numeral “3”;
Enter letters “DEF”;
3/DEF/F2
The F2 button is used to change the tab pages.
In PTZ control mode, it zooms in the image.
Enter numeral “4”;
4/GHI/ESC
Enter letters “GHI”;
Exit and back to the previous menu.
Enter numeral “5”;
Enter letters “JKL”;
5/JKL/EDIT
Delete characters before cursor;
Check the checkbox and select the ON/OFF switch;
Start/stop record clipping in playback.
Enter numeral “6”;
6/MNO/PLAY
Enter letters “MNO”;
Playback, for direct access to playback interface.
Enter numeral “7”;
7/PQRS/REC
Enter letters “PQRS”;
Open the manual record interface.
Enter numeral “8”;
8/TUV/PTZ
Enter letters “TUV”;
Access PTZ control interface.
9/WXYZ/PRE
V
Enter numeral “9”;
Enter letters “WXYZ”;
Multi-channel display in live view.
Enter numeral “0”;
0/A
Shift the input methods in the editing text field. (Upper and
lowercase, alphabet, symbols or numeric input).
Double press the button to switch the main and auxiliary output.
Move the active selection in a menu. It will move the selection up
and down.
In Live View mode, it can be used to cycle through different
channels.
5
JOG SHUTTLE Control
In the Playback mode, it can be used to jump 30s
forward/backward in video files.
In PTZ control mode, it can control the movement of the PTZ
camera.
6
POWER ON/OFF
7
USB Interfaces
8
IR Receiver
Power on/off switch.
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
IR receiver interface
9
Quick Operation Guide of 0700/8800/8700 Series NVR
8716:
No.
Name
Function Description
POWER: the POWER LED turns green when NVR is powered
up.
READY: The LED is green when the device is running
normally.
STATUS: 1.The light is green when the IR remote control is
enabled; 2.The light is red when the function of the composite
1
Status Indicators
keys (SHIFT) are used; 3. The light is out when none of the
above condition is met/
ALARM: the light is red when there is an alarm occurring.
HDD: the LED flashes red when HDD is reading/writing.
Tx/Rx: TX/RX LED flashes green when network connection is
functioning normally.
2
USB Interface
Connects USB mouse or USE flash memory devices.
Enter numeral “1”;
1/MENU
Access the main menu interface.
Enter numeral “2”;
Enter letters “ABC”;
2/ABC/F1
The F1 button when used in a list field will select all items in the
list.
In PTZ Control mode, it will turn on/off PTZ light and when the
image is zoomed in, the key is used to zoom out.
Enter numeral “3”;
Enter letters “DEF”;
3/DEF/F2
The F2 button is used to change the tab pages.
In PTZ control mode, it zooms in the image.
3
Composite
Keys
Enter numeral “4”;
4/GHI/ESC
Enter letters “GHI”;
Exit and back to the previous menu.
Enter numeral “5”;
Enter letters “JKL”;
5/JKL/EDIT
Delete characters before cursor;
Check the checkbox and select the ON/OFF switch;
Start/stop record clipping in playback.
Enter numeral “6”;
6/MNO/PLAY
Enter letters “MNO”;
Playback, for direct access to playback interface.
7/PQRS/REC
Enter numeral “7”;
Enter letters “PQRS”;
10
Quick Operation Guide of 0700/8800/8700 Series NVR
Open the manual record interface.
Enter numeral “8”;
8/TUV/PTZ
Enter letters “TUV”;
Access PTZ control interface.
Enter numeral “9”;
9/WXYZ/PREV
Enter letters “WXYZ”;
Multi-channel display in live view.
Enter numeral “0”;
0/A
Shift the input methods in the editing text field. (Upper and
lowercase, alphabet, symbols or numeric input).
Double press the button to switch the main and auxiliary output.
Switch between the numeric or letter input and functions of the
4
SHIFT
composite keys. (Input letter or numbers when the light is out;
Realize functions when the light is red.)
In menu mode, the direction buttons are used to navigate
between different fields and items and select setting parameters.
In playback mode, the Up and Down buttons are used to speed
DIRECTION
up and slow down record playing, and the Left and Right buttons
are used to move the recording 30s forwards or backwards.
In the image setting interface, the up and down button can adjust
the level bar of the image parameters.
5
Control
In live view mode, these buttons can be used to switch channels.
Buttons
The Enter button is used to confirm selection in menu mode; or
used to check checkbox fields and ON/OFF switch.
In playback mode, it can be used to play or pause the video.
ENTER
In single-frame play mode, pressing the Enter button will play
the video by a single frame.
And in auto sequence view mode, the buttons can be used to
pause or resume auto sequence.
6
IR Receiver
Receiver for IR remote.
11
Quick Operation Guide of 0700/8800/8700 Series NVR
Rear Panel
0700/0700-R
8800
No.
Item
Description
1
VIDEO OUT
BNC connector for video output.
2
CVBS
BNC connector for audio output. This connector is synchronized with CVBS
AUDIO
OUT
video output.
VGA AUDIO OUT
BNC connector for audio output. This connector is synchronized with VGA
video output.
3
LINE IN
BNC connector for audio input.
4
RS-232 Interface
Connector for RS-232 devices.
5
VGA
DB9 connector for VGA output. Display local video output and menu.
6
HDMI
HDMI video output connector.
7
eSATA (Optional)
Connects external SATA HDD, CD/DVD-RM.
8
LAN Interface
1 network interface provided for 8800 and 2 network interfaces for 0700
9
Termination
RS-485 termination switch.
Switch
Up position is not terminated.
Down position is terminated with 120Ω resistance.
RS-485 Interface
Connector for RS-485 devices. T+ and T- pins connect to R+ and R- pins of
PTZ receiver respectively.
D+, D- pin connects to Ta, Tb pin of controller. For cascading devices, the first
Controller Port
NVR’s D+, D- pin should be connected with the D+, D- pin of the next NVR.
ALARM IN
Connector for alarm input.
ALARM OUT
Connector for alarm output.
11
GROUND
Ground(needs to be connected when NVR starts up).
12
AC 100V ~ 240V
AC 100V ~ 240V power supply.
13
POWER
Switch for turning on/off the device.
14
USB interface
Universal Serial Bus (USB) ports for additional devices such as USB mouse
10
and USB Hard Disk Drive (HDD).
12
Quick Operation Guide of 0700/8800/8700 Series NVR
8800-P8
8800-P16
No.
Item
Description
1
VIDEO OUT
BNC connector for video output.
2
CVBS AUDIO OUT
BNC connector for audio output. This connector is synchronized with
CVBS video output.
VGA AUDIO OUT
BNC connector for audio output. This connector is synchronized with
VGA video output.
3
LINE IN
BNC connector for audio input.
4
RS-232 Interface
Connector for RS-232 devices.
5
VGA
DB9 connector for VGA output. Display local video output and menu.
6
HDMI
HDMI video output connector.
7
eSATA (Optional)
Connects external SATA HDD, CD/DVD-RM.
8
LAN Interface
Connector for LAN (Local Area Network).
9
Termination Switch
RS-485 termination switch.
Up position shows the RS-485 is not terminated.
Down position shows the RS-485 is terminated with 120Ω resistance.
RS-485 Interface
Connector for RS-485 devices. T+ and T- pins connects to R+ and Rpins of PTZ receiver respectively.
D+, D- pin connects to Ta, Tb pin of controller. For cascading devices,
Controller Port
the first NVR’s D+, D- pin should be connected with the D+, D- pin of
ALARM IN
Connector for alarm input.
ALARM OUT
Connector for alarm output.
11
GROUND
Ground (needs to be connected when NVR starts up).
12
AC 100V ~ 240V
AC 100V ~ 240V power supply.
13
POWER
Switch for turning on/off the device.
14
USB interface
Universal Serial Bus (USB) ports for additional devices such as USB
10
the next NVR.
mouse and USB Hard Disk Drive (HDD).
15
Network Interfaces with
Network interface for the cameras and to provide power over Ethernet.
PoE function
13
Quick Operation Guide of 0700/8800/8700 Series NVR
8716
No.
Item
Description
1
VIDEO OUT
BNC connector for video output.
2
AUDIO OUT
BNC connector for audio output.
3
AUDIO IN
BNC connector for audio input. (Also for two-way audio)
4
RS-232 Interface
Connector for RS-232 devices.
5
VGA
DB9 connector for VGA output. Display local video output and menu.
6
HDMI
HDMI video output connector.
7
USB
Connects USB disks and devices.
8
LAN Interface
1 network interface.
RS-485 Interface
Connector for RS-485 devices. T+ and T- pins connect to R+ and R-
9
pins of PTZ receiver respectively.
ALARM IN
Connector for alarm input.
ALARM OUT
Connector for alarm output.
10
Power Supply
12VDC power supply.
11
Power Switch
Switch for turning on/off the device.
14
Quick Operation Guide of 0700/8800/8700 Series NVR
Peripheral Connections
Wiring of Alarm Input / Output
The alarm input/output interface of the NVR is shown as below:
The alarm input is an open/closed relay. If the input is not an open/closed relay, follow the connection diagram
below:
NVR
Relay alarm
input
NVR
Relay alarm
input
To connect to an alarm output (AC/DC load), use the following diagram:
For DC load, JP4 can be used within the limit of 12V/1A safely. If the interface is connected to an AC load, JP4
should be left open. Use an external relay for safety (as shown in the figure above).
There are 4 jumpers (JP1, JP2, JP3, and JP4) on the motherboard, each corresponding with one alarm output. By
default, jumpers are connected. To connect an AC load, jumpers should be removed.
Note: An external relay is needed to prevent electric shock when connecting to an AC load.
Using of Alarm Connectors
To connect alarm devices to the NVR:
1. Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block.
2. Unfasten stop screws from the pluggable block, insert signal cables into slots and fasten stop screws. Ensure
signal cables are in tight.
3. Connect pluggable block back into terminal block.
15
Quick Operation Guide of 0700/8800/8700 Series NVR
Controller Connection
To connect a controller to the NVR:
1.
Disconnect pluggable block from the KB terminal block.
2.
Unfasten stop screws from the KB D+, D- pluggable block, insert signal cables into slots and fasten stop
screws. Ensure signal cables are in tight.
3.
Connect Ta on controller to D+ on terminal block and Tb on controller to D- on terminal block. Fasten stop
screws.
4.
Connect pluggable block back into terminal block.
Note: Make sure both the controller and NVR are grounded.
16
Quick Operation Guide of 0700/8800/8700 Series NVR
Specifications
Specifications of 0700
Model
Video/Audio
input
0708
0716
0732
0764
IP video input
8-ch
16-ch
32-ch
64-ch
Two-way audio
1-ch, BNC (2.0 Vp-p, 1kΩ)
Recording
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Main stream: 25 fps (P) / 30 fps (N)
Frame rate
Sub-stream: 25 fps (P) / 30 fps (N)
Video/Audio
output
CVBS output
1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 ×576 (PAL); 704 × 480 (NTSC)
HDMI output
1-ch, resolution:
1920 × 1080P /60Hz, 1920×1080P /50Hz, 1600 × 1200/60Hz,
1280 ×1024 /60Hz, 1280 × 720 /60Hz, 1024 ×768 /60Hz
VGA output
1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz,
1280 ×720 /60Hz, 1024 ×768 /60Hz
Audio output
2-ch, BNC (Linear, 600Ω)
Playback
resolution
Synchronous
playback
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
External
interface
Others
16-ch
16-ch
16-ch
eSATA
8 SATA interfaces for 4 HDDs + 1 DVD-R/W (default), or
8HDDs
1 eSATA interface
Capacity
Up to 4TB capacity for each HDD
Network interface
2 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interfaces
Serial interface
RS-232; RS-485; Keyboard
USB interface
3 × USB 2.0
Alarm in
16
Alarm out
4
Power supply
100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz
SATA
Hard disk
8-ch
Consumption
(without
hard
disk
or
DVD-R/W)
Working
temperature
Working
humidity
≤ 35 W
≤ 40 W
≤ 45 W
≤ 45 W
-10 ℃ ~ +55 ℃
10 % ~ 90 %
Chassis
19-inch rack-mounted 2U chassis
Dimensions
(W × D × H)
445 × 470 ×90 mm (17.52" ×18.5"× 3.54")
Weight
≤ 8 Kg (17.64 lb) ( without hard disk or DVD-R/W )
17
Quick Operation Guide of 0700/8800/8700 Series NVR
Specifications of 0700-R
Model
Video/Audio
input
0708-R
0716-R
0732-R
0764-R
IP video input
8-ch
16-ch
32-ch
64-ch
Two-way audio
1-ch, BNC (2.0 Vp-p, 1kΩ)
Recording
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Main stream: 25 fps (P) / 30 fps (N)
Frame rate
Sub-stream: 25 fps (P) / 30 fps (N)
Video/Audio
output
Hard disk
Disk array
CVBS output
1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 ×576 (PAL); 704 × 480 (NTSC)
HDMI output
1-ch, resolution:
1920 × 1080P /60Hz, 1920×1080P /50Hz, 1600 × 1200/60Hz, 1280
× 1024 /60Hz, 1280 × 720 /60Hz, 1024 ×768 /60Hz
VGA output
1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz,
1280 ×720 /60Hz, 1024 ×768 /60Hz
Audio output
2-ch, BNC (Linear, 600Ω)
Playback
resolution
Synchronous
playback
SATA
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity for each HDD
Array type
RAID0, RAID1, RAID5, RAID10
Number of array
4
Number of virtual
disk
External
interface
Others
8-ch
16-ch
16-ch
16-ch
8 SATA interfaces for 4 HDDs + 1 DVD-R/W (default), or 8HDDs
8
Network interface
2 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interfaces
Serial interface
RS-232; RS-485; Keyboard
USB interface
3 × USB 2.0
Alarm in
16
Alarm out
4
Power supply
100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz
Consumption
(without
hard
disk
or
DVD-R/W)
Working
temperature
Working
humidity
≤ 35 W
≤ 40 W
≤ 45 W
-10 ℃ ~ +55 ℃
10 % ~ 90 %
Chassis
19-inch rack-mounted 2U chassis
Dimensions
(W × D × H)
445 × 470 ×90 mm (17.52" ×18.5"× 3.54")
Weight
≤ 8 Kg (17.64 lb) ( without hard disk or DVD-R/W )
18
≤ 45 W
Quick Operation Guide of 0700/8800/8700 Series NVR
Specification of 8800
Model
Video/Audio
input
8808
8816
8832
IP video input
8-ch
16-ch
32-ch
Two-way audio
1-ch, BNC (2.0 Vp-p, 1kΩ)
Recording
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Main stream: 25 fps (P) / 30 fps (N)
Frame rate
Sub-stream: 25 fps (P) / 30 fps (N)
CVBS output
Video/Audio
output
HDMI output
VGA output
Hard disk
External
interface
Others
1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 ×576 (PAL); 704 × 480 (NTSC)
1-ch, resolution:
1920 × 1080P /60Hz, 1920 × 1080P /50Hz, 1600 × 1200 /60Hz, 1280
× 1024 /60Hz, 1280 × 720 /60Hz, 1024 ×768 /60Hz
1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280
× 720 /60Hz, 1024 ×768 /60Hz
Audio output
2-ch, BNC (Linear, 600Ω)
Playback
resolution
Synchronous
playback
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
SATA
4 SATA interfaces for 2 HDDs + 1 DVD-R/W (default), or 4HDDs
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity for each HDD
Network interface
1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface
Serial interface
RS-232; RS-485; Keyboard
USB interface
3 × USB 2.0
Alarm in
16
Alarm out
4
Power supply
100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz
Consumption
(without hard disk
or DVD-R/W)
Working
temperature
8-ch
16-ch
≤ 35 W
≤ 40W
16-ch
≤ 45 W
-10 ℃ ~ +55 ℃
Working humidity
10 % ~ 90 %
Chassis
19-inch rack-mounted 2U chassis
Dimensions
(W × D × H)
445 × 390 ×90 mm
Weight
≤ 4 Kg (8.82 lb) ( without hard disk or DVD-R/W )
19
Quick Operation Guide of 0700/8800/8700 Series NVR
Specification of 8800-P8
Model
Video/Audio
input
8808-P8
8816-P8
8832-P8
IP video input
8-ch
16-ch
32-ch
Two-way audio
1-ch, BNC (2.0 Vp-p, 1kΩ)
Recording
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Main stream: 25 fps (P) / 30 fps (N)
Frame rate
Sub-stream: 25 fps (P) / 30 fps (N)
CVBS output
1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 ×576 (PAL); 704 × 480 (NTSC)
HDMI output
1-ch, resolution:
1920 × 1080P /60Hz, 1920 × 1080P /50Hz, 1600 × 1200 /60Hz, 1280
× 1024 /60Hz, 1280 × 720 /60Hz, 1024 ×768 /60Hz
VGA output
1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280
× 720 /60Hz, 1024 ×768 /60Hz
Audio output
2-ch, BNC (Linear, 600Ω)
Playback
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Synchronous
playback
8-ch
SATA
4 SATA interfaces for 2 HDDs + 1 DVD-R/W (default), or 4HDDs
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity for each HDD
Video/Audio
output
Hard disk
16-ch
16-ch
1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface
Network interface
8 independent 100 Mbps PoE network interfaces
External
interface
Others
Serial interface
RS-232; RS-485; Keyboard
USB interface
3 × USB 2.0
Alarm in
16
Alarm out
4
Power supply
100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz
Consumption
(without hard disk
or DVD-R/W)
Working
temperature
≤ 35 W
≤ 40W
≤ 45 W
-10 ℃ ~ +55 ℃
Working humidity
10 % ~ 90 %
Chassis
19-inch rack-mounted 2U chassis
Dimensions
(W × D × H)
445 × 390 ×90 mm
Weight
≤ 8 Kg (17.64 lb) ( without hard disk or DVD-R/W )
20
Quick Operation Guide of 0700/8800/8700 Series NVR
Specification of 8800-P16
Model
Video/Audio
input
8816-P16
8832-P16
IP video input
16-ch
32-ch
Two-way audio
1-ch, BNC (2.0 Vp-p, 1kΩ)
Recording
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF
Main stream: 25 fps (P) / 30 fps (N)
Frame rate
Sub-stream: 25 fps (P) / 30 fps (N)
CVBS output
1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 ×576 (PAL); 704 × 480 (NTSC)
HDMI output
1-ch, resolution:
1920 × 1080P /60Hz, 1920 × 1080P /50Hz, 1600 × 1200 /60Hz, 1280 ×
1024 /60Hz, 1280 × 720 /60Hz, 1024 × 768 /60Hz
VGA output
1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz,
720 /60Hz, 1024 ×768 /60Hz
Audio output
2-ch, BNC (Linear, 600Ω)
Playback
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF
Synchronous
playback
16-ch
SATA
4 SATA interfaces for 2 HDDs + 1 DVD-R/W (default), or 4HDDs
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity for each HDD
Video/Audio
output
Hard disk
Network
interface
External
interface
Others
16-ch
1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface
16 independent 100 Mbps PoE network interfaces
Serial interface
RS-232; RS-485; Keyboard
USB interface
3 × USB 2.0
Alarm in
16
Alarm out
4
Power supply
100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz
Consumption
(without
hard
disk
or
DVD-R/W)
Working
temperature
Working
humidity
≤ 40W
≤ 45 W
-10 ℃ ~ +55 ℃
10 % ~ 90 %
Chassis
19-inch rack-mounted 2U chassis
Dimensions
(W × D × H)
445 × 390 ×90 mm
Weight
≤ 8 Kg (17.64 lb) ( without hard disk or DVD-R/W )
21
1280 ×
Quick Operation Guide of 0700/8800/8700 Series NVR
Specifications of 8700
Model
Video/Audio
input
8716
IP video input
16-ch
Audio in
1-ch, BNC (2.0 Vp-p, 1kΩ) (Two-way audio)
Recording
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Main stream: 25 fps (P) / 30 fps (N)
Frame rate
Sub-stream: 25 fps (P) / 30 fps (N)
CVBS output
Video/Audio
output
HDMI output
VGA output
Hard disk
External
interface
Others
1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 ×576 (PAL); 704 × 480 (NTSC)
1-ch, resolution:
1920 × 1080P /60Hz, 1920 × 1080P /50Hz, 1600 × 1200 /60Hz, 1280
× 1024 /60Hz, 1280 × 720 /60Hz, 1024 ×768 /60Hz
1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280
× 720 /60Hz, 1024 ×768 /60Hz
Audio output
1-ch, BNC (Linear, 600Ω)
Playback
resolution
Synchronous
playback
SATA
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Capacity
Each interface supports up to 4TB capacity for recording
Network interface
1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface
Serial interface
RS-232; RS-485;
USB interface
2 × USB 2.0
Alarm in
4
Alarm out
2
Power supply
12 VDC
Consumption
≤ 13 W (without hard disk or DVD-R/W)
Working
temperature
-10 ℃ ~ +55 ℃
Working humidity
10 % ~ 90 %
Chassis
19-inch rack-mounted 1U chassis
Dimensions
(W × D × H)
445 × 261 ×44.5 mm
Weight
≤ 4 Kg (8.82 lb) ( without hard disk or DVD-R/W )
16-ch
2 SATA interfaces
22
Quick Operation Guide of 0700/8800/8700 Series NVR
Specifications of 8700-P8
Model
Video/Audio
input
8708-P8
8716-P8
IP video input
8-ch
16-ch
Audio in
1-ch, BNC (2.0 Vp-p, 1kΩ) (Two-way audio)
Recording
resolution
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
Main stream: 25 fps (P) / 30 fps (N)
Frame rate
Sub-stream: 25 fps (P) / 30 fps (N)
CVBS output
Video/Audio
output
HDMI output
VGA output
Hard disk
1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 ×576 (PAL); 704 × 480 (NTSC)
1-ch, resolution:
1920 × 1080P /60Hz, 1920 × 1080P /50Hz, 1600 × 1200 /60Hz, 1280
× 1024 /60Hz, 1280 × 720 /60Hz, 1024 ×768 /60Hz
1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280
× 720 /60Hz, 1024 ×768 /60Hz
Audio output
1-ch, BNC (Linear, 600Ω)
Playback
resolution
Synchronous
playback
5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF
/QCIF
SATA
2 SATA interfaces
Capacity
Each interface supports up to 4TB capacity for recording
8-ch
16-ch
1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface
Network interface
8 independent 100 Mbps PoE network interfaces
External
interface
Others
Serial interface
RS-232; RS-485;
USB interface
2 × USB 2.0
Alarm in
4
Alarm out
2
Power supply
12 VDC
Consumption
≤ 13 W (without hard disk or DVD-R/W)
Working
temperature
-10 ℃ ~ +55 ℃
Working humidity
10 % ~ 90 %
Chassis
19-inch rack-mounted 1U chassis
Dimensions
(W × D × H)
445 × 261 ×44.5 mm
Weight
≤ 4 Kg (8.82 lb) ( without hard disk or DVD-R/W )
23
Quick Operation Guide of 0700/8800/8700 Series NVR
HDD Storage Calculation Chart
The following chart shows an estimation of storage space used based on recording at one channel for an hour at a
fixed bit rate.
Bit Rate
96K
128K
160K
192K
224K
256K
320K
384K
448K
512K
640K
768K
896K
1024K
1280K
1536K
1792K
2048K
Storage Used
42M
56M
70M
84M
98M
112M
140M
168M
196M
225M
281M
337M
393M
450M
562M
675M
787M
900M
Note: Please note that supplied values for storage space used is just for reference. The storage values in the chart
are estimated by formulas and may have some deviation from actual value.
24
Quick Operation Guide of 0700/8800/8700 Series NVR
Menu Operation
Menu Structure
The menu structure of the 0700/8800/8700 Series NVR:
The menu structure of the 0700-R Series NVR:
25
Quick Operation Guide of 0700/8800/8700 Series NVR
Startup and Shutdown
Proper startup and shutdown procedures are crucial to expanding the life of the NVR.
To start your NVR:
1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power LED on the front
panel should be red, indicating the device gets the power supply.
2. Press the POWER button on the front panel. The Power LED should turn green. The unit will begin to start.
To shut down the NVR:
1. Enter the Shutdown menu.
Menu > Shutdown
Shutdown Menu
2. Select the Shutdown button.
3. Click the Yes button.
Using the Start Wizard
By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure below.
Start Wizard Interface
Operating the Setup Wizard:
1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the
Setup Wizard at that moment, click the Cancel button. You can also choose to use the Setup Wizard next
time by leaving the “Start wizard when NVR starts?” checkbox checked.
2. Click Next button on the Wizard window to enter the Login window.
26
Quick Operation Guide of 0700/8800/8700 Series NVR
Login Window
3. Enter the admin password. By default, the password is 12345.
4. To change the admin password, check the New Admin Password checkbox. Enter the new password and
confirm the password in the given fields.
5. Click the Next button to enter the date and time settings window.
Date and Time Settings
6. After the time settings, click Next button which takes you back to the Network Setup Wizard window.
27
Quick Operation Guide of 0700/8800/8700 Series NVR
0700
8700/8800
Network Configuration
Note: Dual-NIC is only supported by 0700 series device. And for 8700/8800-P8 series NVR, the internal NIC IPv4
address should be configured for the cameras connecting to the PoE network interface of the NVR.
7. Click Next button after you configured the network parameters, which takes you to the Array Management
window (supported by 0700-R series only).
28
Quick Operation Guide of 0700/8800/8700 Series NVR
Array Management
8. Click Next button after you configured the network parameters, which takes you to the HDD Management
window.
HDD Management
9. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.
10. Click Next button. You enter the Adding IP Camera interface.
11. Click Search to find online IP Camera. Select the IP camera to be added, and click the Add button.
29
Quick Operation Guide of 0700/8800/8700 Series NVR
Search for IP Cameras
12. Click Next button. Configure the recording for the searched IP Cameras.
Record Settings
13. Click Copy to copy the settings to other channels.
Copy Record Settings
30
Quick Operation Guide of 0700/8800/8700 Series NVR
14. Click OK to complete the startup Setup Wizard.
Live View
Some icons are provided on screen in Live View mode to indicate different camera status. These icons include:
Live View Icons
In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can find problems as soon as possible.
Alarm (video loss, tampering, motion detection or sensor alarm).
Record (manual record, schedule record, motion detection or alarm triggered record)
Alarm & Record
Adding and Configuring IP Cameras
You should add and configure the online IP cameras to enable the live view and recording function.
Adding IP Cameras
You can search and add the online IP cameras by following the startup wizard, or according to the following steps.
Steps:
1.
Enter the Camera Management interface.
Menu> Camera> Camera
Main Menu
2.
To add the online cameras with same network segment:
1)
Click Search to search the online cameras.
31
Quick Operation Guide of 0700/8800/8700 Series NVR
Camera Settings Interface
3.
2)
Check the checkbox of certain cameras to be added.
3)
Click Quick Add to add the camera.
To add other IP cameras:
1)
On the left side of the interface, you can enter the IP address, protocol, management port, and other
information of the IP camera to be added.
2)
Click Add to add the camera.
Note: If you check the Synchronize IP Camera checkbox, the default settings of the NVR for the IP
camera is applied to the added camera.
Configuring Basic Parameters of IP Cameras
After the adding of the IP cameras, the basic information of the camera lists in the page, and you can configure the
basic setting of the IP cameras.
Steps:
1.
Click the
icon to edit the parameters; you can edit the IP address, protocol and other parameters.
32
Quick Operation Guide of 0700/8800/8700 Series NVR
Edit the Parameters
2.
Click apply to save the settings and click OK to exit the editing interface.
To edit more parameters:
1.
Click the
icon.
Network Configuration of the Camera
2.
You can edit the network information and the password of the camera.
3.
Click Apply to save the settings and click OK to exit the interface.
Explanation of the icons:
Edit basic parameters of the camera
Delete the IP camera
Get the live view of the camera
PTZ Control
Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before
you set the PTZ camera.
Before you start, please check that the PTZ and the NVR are connected properly through RS-485 interface.
33
Quick Operation Guide of 0700/8800/8700 Series NVR
PTZ Settings
Steps:
1.
Enter the PTZ Settings interface.
Menu >Camera> PTZ
Camera Settings Interface
2.
Choose the camera for PTZ setting next to Camera label.
3.
Enter the parameters of the PTZ camera.
Note: All the parameters should be exactly the same as the PTZ camera parameters.
4.
Click Copy if you want to configure same settings to other PTZ cameras.
5.
Click the Apply button to save and exit the interface.
PTZ Control
In the Live View mode, you can press the PTZ Control button on the front panel or on the remote, or choose the
PTZ Control icon
to enter the PTZ panel.
PTZ Control panel
Description of the PTZ panel icons
Icon
Description
Icon
Description
Direction button and
Zoom+, Focus+,
the auto-cycle button
Iris+
Icon
Description
Zoom-, Focus-, Iris-
The speed of the
Light on/off
PTZ movement
34
Wiper on/off
Quick Operation Guide of 0700/8800/8700 Series NVR
Icon
Description
Icon
Description
Icon
Description
Image
3D-Zoom
Preset
Centralization
Patrol
Pattern
Menu
Previous item
Next item
Start pattern/patrol
Stop the patrol or
Minimize
pattern movement
windows
Exit
Playback
Play back the record files of a specific channel in the live view menu. Channel switch is supported.
Instant playback by channel
Choose a channel under live view using the mouse and click the
button in the shortcut operation menu.
Note: Only record files recorded during the past five minutes on this channel will be played back.
Instant Playback Interface
Playback by channel
Steps:
1.
Enter the Playback menu.
Mouse: right click a channel in live view mode and select Playback from the menu.
35
Quick Operation Guide of 0700/8800/8700 Series NVR
Right-click Menu under Live View
Front Panel: press PLAY button to play back record files of the channel under single-screen live view.
Under multi-screen live view, record files of the top left channel (not masked) will be played back.
Note: pressing numerical buttons will switch playback to related channels during playback process.
2.
Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing process.
Playback Interface
Just check the channel or channels if you want to switch playback to another channel or execute
simultaneous playback of multiple channels.
Backup
Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer.
Steps:
1.
Enter Video Export interface.
Choose the channel(s) you want to back up and click on the
36
button.
Quick Operation Guide of 0700/8800/8700 Series NVR
Quick Export Interface
2.
Enter Export interface, choose backup device and press Export button to start exporting.
Quick Export using USB1-1
3.
Check backup result.
Choose the record file in Export interface and press button
to check it.
Checkup of Quick Export Result Using USB1-1
37
Quick Operation Guide of 0700/8800/8700 Series NVR
Accessing by Web Browser
Logging In
If the device has successfully connected to the network, you can get access to the device via web browser. Open
web browser, input the IP address of the device and then press Enter. The login interface appears.
Input the user name and password, and click the Login button.
Notes:
1. The default IP address is 192.0.0.64.
2. The default user name is admin, and password is 12345.
3. You may use one of the following listed web browsers: Internet Explorer 6.0, Internet Explorer 7.0, Internet
Explorer 8.0, Internet Explorer 9.0, Internet Explorer 10.0, Apple Safari, Mozilla Firefox, and Google Chrome.
4. The supported resolutions include 1024*768 and above.
When you log in for the first time, the system will remind you to install the Plug-in control. After the installation,
you can configure and manage the device remotely.
Live View
The live view interface appears by default when you log in the device.
Interface Introduction
① Camera List: Displays the list of cameras and the playing and recording status of each camera.
② Live View Window: Displays the image of camera, and multi-window division is supported.
③ Play Control Bar: Play control operations are supported.
④ PTZ Control: Pan, tilt, zoom operations are supported, as well as preset editing and calling.
Note: PTZ function can only be realized if the connected camera supports PTZ control.
⑤ Video Parameters Configuration: Brightness, contrast, saturation and other parameters of the image can be
modified.
38
Quick Operation Guide of 0700/8800/8700 Series NVR
Start Live View
Steps:
1.
In the live view window, select a playing window by clicking the mouse.
2.
Double-click a camera from the device list to start the live view.
3.
You can click the
button on the toolbar to start the live view of all cameras on the device list.
Refer to the following table for the description of buttons on the live view window:
Icon
Description
Icon
Description
Select the
window-division
/
Start/Stop all live view
mode
Capture pictures in
Start/Stop all
/
the live view mode
Previous page
/
recording
Next page
Start/Stop two-way
Open/Close audio
/
Adjust volume
/
audio
Enable/Disable digital
zoom
Full-screen
Recording
Before you start
Make sure the device is connected with HDD or network disk, and the HDD or network disk has been initialized
for the first time to use.
Two recording types can be configured: Manual and Scheduled. The following section introduces the
configuration of scheduled recording.
Steps:
1.
Click Remote Configuration> Camera Settings> Record Schedule to enter Record Schedule settings interface.
2.
Select the camera to configure the record schedule.
3.
Check the checkbox of Enable Record Schedule to enable recording schedule.
4.
Click Edit to edit record schedule.
5.
Choose the day in a week to configure scheduled recording.
1)
Configure All Day or Customize record:

If you want to configure the all-day recording, please check the All Day checkbox.

If you want to record in different time sections, check the Customize checkbox. Set the Start Time and
End Time.
Note: The time of each segment can’t be overlapped. Up to 8 segments can be configured.
2)
Select a Record Type. The record type can be Normal, Motion, Alarm, Motion & Alarm, and Motion |
Alarm.
3)
Check the checkbox of Select All and click Copy to copy settings of this day to the whole week. You
can also check any of the checkboxes before the date and click Copy.
4)
Click OK to save the settings and exit the Edit Schedule interface.
6.
Click Advanced to configure advanced record parameters.
7.
Optionally, check the checkboxes of other cameras to copy the settings to.
8.
Click Save to validate the above settings.
39
Quick Operation Guide of 0700/8800/8700 Series NVR
Playback
Interface Introduction
① Camera List: Displays the list of cameras and the playing status of each camera.
② Playback Window: Displays the video of camera.
③ Play Control Bar: Play control operations are supported.
④ Time Line: Displays the time bar and the records marked with different colors.
⑤ Playback Status: Displays the playback status, including camera No. and playback speed.
⑥ Calendar: You can select the date to play.
Start Playback
Steps:
1.
Click Playback on the menu bar to enter playback interface.
2.
Click the camera from the device list for playback.
3.
Select the date from the calendar and click Search.
Note: The day with record will be marked like
.
4.
Click the
button to play the video file searched on the current date.
5.
Use the buttons on the toolbar to operate in playback mode.
Button
Description
/
Play/Pause
Stop
Slow down
Speed up
Play by single frame
Capture
Stop All Playback
Download
/
Button
Video Clip
Description
Open/Close audio
/
Full-screen
6.
You can drag the progress bar with the mouse to locate the exact playback point. You can also input the time
in the textbox
and click
button to locate the playback point.
The color of the video on the progress bar stands for the different video types.
40
Quick Operation Guide of 0700/8800/8700 Series NVR
Log
You can view and export the log files at any time, including operation, alarm, exception and information of device.
Before you start
The Log function can be realized only when the device is connected with HDD or network disk. And make sure
the HDD or network disk has been initialized for the first time to use.
Steps:
1.
Click Log on the menu bar to enter the Log interface.
2.
Set the log search conditions to refine your search, including the Major Type, Minor Type, Start Time and
End Time.
3.
Click the Search button to start searching log files.
4.
The matched log files will be displayed on the list shown below.
Note: Up to 100 log files can be displayed on each page.
You can click the
button to save the searched log files to local directory.
41
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising