Your professional partner

Your professional partner
KOLLER GmbH · Kufsteiner Wald 26 · A-6334 Schwoich bei Kufstein/Austria · Tel. 0043-5372-63257 · Fax 63257-7
Your professional partner
Edition 2015
www.kollergmbh.com
K 300 T
Tractor mounted yarder – for uphill logging
The K300T is an internationally approved tractor / 3-point mounted yarder for uphill logging.
It assures easy handling, reliable and rugged design, as well as short rig up and dismantling times.
A hydraulically raised lattice tower is standard.
 Worldwide, over 450 in use
 Compact and cost-effective solution for small volume harvest
 Ideal for the small woodlot owner
T E C H N I C A L
D A T A :
Line pull:
Skyline
Mainline
9,700 lbs / 44 kN
3,970 lbs / 18 kN
(tension section)
(average drum)
Line capacity:
Skyline 1650’ Ø 9/16” /
500 m Ø 14 mm swaged
(1300’ Ø 5/8” / 450 m Ø 15 mm)
Mainline
2250’ Ø 5/16” /
550 m Ø 8 mm swaged
(1450’ Ø 3/8” / 450 m Ø 9 mm)
Guyline
3x100’ Ø 5/8” / 3x30 m Ø 16 mm
2x30’ / 2x10 m extensions
Line speed:
Unloaded drive
Loaded drive
user defined by brake
up to 705 ft/min / 215 m/min
Tower:
Standard
24’ / 7,2 m
With tower extension 28’ / 8,4 m
Operating range
on the left side of the yarder
K 300T w i th standard tower
Power station:
 P.T.O. of the tractor (mechanically driven)
 Engine power of the tractor: minimum 49 HP (36 kW)
 Hydraulically operated single disk dry clutches
on both drums
Brakes:
Skyline
Mainline
manually actuated band brake
hydraulically actuated spring-applied
band brake
Operation:
 Hydromechanical / electro-hydraulic single lever
operation with dead-man´s control
Carriage:
SKA 1 / SKA 1-Z
Weight:
3,400 lbs / 1.550 kg without lines
4,500 lbs / 2.050 kg including lines
4,950 lbs / 2.250 kg including lines
(non-swaged lines)
(swaged lines)
2
w w w . k o l l e r g m b h . c o m
K 301 T
Tractor mounted yarder – for uphill logging
The K301T is a tractor / 3-point mounted yarder for uphill logging.
It assures easy handling, reliable and rugged design, as well as very short rig up and dismantling time.
Particularly suitable for thinning and small wood harvesting operations.
 Logging is possible off both sides of the yarder
 Compact and cost-effective solution for small diameter tree harvest
 Ideal for the start-up companies
T E C H N I C A L
D A T A :
Line pull:
Skyline
Mainline
11,000 lbs / 50 kN (tension section)
5,740 lbs / 26 kN (average drum)
Line capacity:
Skyline
1700’ Ø 5/8” /
500 m Ø 16 mm swaged
(1150’ Ø 3/4” / 400 m Ø 18 mm)
Mainline
1800’ Ø 3/8” /
630 m Ø 9 mm swaged
(1250’ Ø 7/16” / 500 m Ø 10 mm)
Guyline
4x160’ Ø 5/8” / 4x50 m Ø 16 mm
2x30’ / 2x10 m extensions
Line speed:
Unloaded drive
Loaded drive
user defined by brake
up to 605 ft/min / 185 m/min
up to 740 ft/min / 255 m/min
K 301T w i th tower extensi on
(with optional auxiliary transmission)
Tower:
Standard
29’ / 8,8 m
With tower extension 33’ / 10,0 m
Operating range
360°
Power station:
 P.T.O. of the tractor (mechanically driven)
 Engine power of the tractor: minimum 89 HP (66 kW)
120 HP (90 kW) with an auxiliary transmission
 Hydraulically operated single disk dry clutches
on both drums
Brakes:
Skyline
Mainline
manually actuated band brake
hydraulically actuated spring-applied
band brake
Operation:
 Hydromechanical / electro-hydraulic single lever
operation with dead-man´s control
Carriage:
SKA 1 / SKA 1-Z
Weight:
5,000 lbs / 2.260 kg without lines
6,950 lbs / 3.150 kg including lines
7,600 lbs / 3.450 kg including lines
(non-swaged lines)
(swaged lines)
K 301T w i th standard tower
w w w . k o l l e r g m b h . c o m
3
K 300 H / K 303 H Trailer
Trailer mounted yarder - for uphill and downhill logging
The K300H is a yarder for uphill logging with an optional haulbackline drum (K303H).
Also for downhill logging and for flat terrain. It assures easy handling, reliable and rugged design, as well as very short rig up
and dismantling times.
 Lightweight and compact yarder mounted on a single axle trailer
 For thinning, selective cuts and small wood harvesting operations
 Cost-effective and lightweight 3-drum yarder
T E C H N I C A L
D A T A :
Line pull:
Skyline
Mainline
Haulbackline
9,700 lbs / 44 kN
3,970 lbs / 18 kN
3,970 lbs / 18 kN
(tension section)
(average drum)
(average drum)
Line capacity:
Skyline 1650’ Ø 9/16” /
500 m Ø 14 mm swaged
(1300’ Ø 5/8” / 450 m Ø 15 mm)
Mainline
2250’ Ø 5/16” /
550 m Ø 8 mm swaged
(1450’ Ø 3/8” / 450 m Ø 9 mm)
Haulbackline (only K303H)2900’ Ø 3/8” / 980 m Ø 9 mm
(2050’ Ø 7/16” / 800 m Ø 10 mm)
Guyline
3 or 4x100’ Ø 5/8” /
3 or 4x30 m Ø 16 mm
2x30’ / 2x10 m extensions
K 303H w i th tower extensi on
Line speed:
Mainline
Unloaded drive
user defined (by brake) or
up to 1115 ft/min / 340 m/min
hydrostatic
Loaded drive
up to 1115 ft/min / 340m/min
Haulbackline
Unloaded drive
up to 1500 ft/min / 460m/min
Loaded drive
up to 750 ft/min / 230m/min
Tower:
Standard
24’ / 7,2 m
With tower extension 28’ / 8,4 m
Operating range
on the left side of the yarder
Power station:
 Deutz 4-cylinder diesel engine with 101 HP (75 kW)
 Continuous hydrostatic transmission for all winches
 Hydraulically operated single disk dry clutches on the
skyline / mainline drum and oil motor on the
haulbackline drum
K 300H w i th standard tower
Brakes:
Skyline
manually actuated band brake
Mainline
hydraulically actuated band brake
Haulbackline hydraulically actuated shoe brake
Operation:
 Hydromechanical / electro-hydraulic single lever
operation with dead-man´s control for up and downhill
logging with hydraulic interlock
Carriage:
SKA 1 / SKA 1-Z / USKA 1,5
Total weight:
K300: 8,400 lbs / 3.800 kg including lines
K303: 10,600 lbs / 4.800 kg including lines
4
For non-European market only.
K 303H w i th standard tower
w w w . k o l l e r g m b h . c o m
K 307 H Trailer
Trailer mounted yarder - for uphill and downhill logging
NE
W
The K307H is a development of the K306H with new winch transmission and improved towerhead. The K307H
is a proven yarder for uphill and downhill logging with an optional haulbackline drum. It is principally used for
thinning, selective cuts and for general wood harvesting operations. A tandem axle trailer with pressure air-brakes is used as
a carrier.
 4 hydraulically powered guyline winches – operation by radio control
 Skyline spooling guided by hydraulic cylinder
 Large dimension, maintenance-free radial air clutches
T E C H N I C A L
Line pull:
Skyline
Mainline
Haulbackline
Line capacity:
Skyline
Mainline
Haulbackline
Straw line
Guyline
Line speed:
Mainline
Unloaded drive
Loaded drive
Haulbackline
Unloaded drive
Loaded drive
Tower:
Standard
Foldable tower
Operating range
D A T A :
14,330 lbs / 65 kN (tension section)
5,500 lbs / 25 kN (average drum)
5,280 lbs / 24 kN (average drum)
2800’ Ø 5/8” /
840 m Ø 16 mm swaged
2500’ Ø 3/8” /
840 m Ø 9 mm swaged
5400’ Ø 3/8” /
1850 m Ø 9 mm swaged
6800’ Ø 3/16” / 1900 m Ø 5 mm
4x160’ Ø 5/8” / 4x50 m Ø 16 mm
2x30’ / 2x10 m extensions
up to 2100 ft/min / 640 m/min
up to 1150 ft/min / 350 m/min
K 307H w i th hydraul i cal l y fol dabl e tower
up to 1540 ft/min / 470 m/min
up to 1050 ft/min / 320 m/min
33’ / 10,2 m
33’ / 10,2 m
360°
Power station:
 Deutz 4-cylinder diesel engine with 168 HP (125 kW)
 Continuous hydrostatic transmission for all winches
 Pneumatically operated radial clutches
on the skyline / mainline drum
Brakes:
Skyline
hydraulically actuated
disk brake
Mainline
hydraulically actuated
band brake
Haulbackline hydraulically actuated
multi-disk brake
Straw line
hydraulically actuated
multi-disk brake
spring-applied
spring-applied
spring-applied
spring-applied
Steuerung:
 KollerMultiMatik by operator console
 Radio control for auxiliary functions
Carriage:
SKA 1-Z / USKA 1,5
Total weight including lines:
Trailer for uphill logging: 19,800 lbs / 9.000 kg
Trailer for up and downhill logging: 24,300 lbs / 11.000 kg
Add. weight - foldable tower (optional): 265 lbs / 120 kg
K 307H for uphi l l and dow nhi l l l oggi ng
w w w . k o l l e r g m b h . c o m
5
K 602 H Trailer
Trailer mounted yarder - for uphill and downhill logging
The K602H is a powerful yarder for uphill, downhill or flat terrain logging with an optional haulbackline. It is principally used for
selective cuts and for general wood harvesting operations. A tandem axle trailer with pressure air-brakes is used as a carrier.
The trailer supports are hydraulic.
 Proven components and maximum power – long reach and high line pull power
 Optional with hydrostatic axle drive – electrically controlled by the engine of the trailer
 Adaptable by many options to suit your individual requirements
 Skyline spooling guided by hydraulic cylinder
T E C H N I C A L
6
D A T A :
Line pull:
Skyline
Mainline
Haulbackline
Line capacity:
Skyline
Mainline
Haulbackline
700 m Ø 13/16” / 2250’ Ø 7/8” /
830 m Ø 20 mm swaged
2100’ Ø 1/2” /
730 m Ø 12 mm swaged
3950’ Ø 1/2” /
1350 m Ø 12 mm swaged
(5150’ Ø 7/16” / 1600 m Ø 11 mm swaged)
20,940 lbs / 95 kN (tension section)
11,020 lbs / 50 kN (average drum)
9,480 lbs / 43 kN (average drum)
Straw line
5500’ Ø 1/4” / 1700 m Ø 6 mm
Guyline
4 or 5x160’ Ø 3/4” /
4 or 5x50 m Ø 20 mm
2x50’ / 2x15 m extensions
Line speed:
Mainline
up to 1960 ft/min / 600 m/min
Haulbackline
Unloaded drive
up to 1655 ft/min / 504 m/min
Loaded drive
up to 1260 ft/min / 384 m/min
Tower (according to country-specific traffic laws!):
Standard
34’ / 10,5 m
With tower extension possible up to 46’ / 14 m
Foldable tower
34’ / 10,5 m
Telescopic tower
up to 44’ / 13,5 m (two working positions)
Operating range
360°
Power station:
 Deutz 6-cylinder diesel engine with 197 HP (147 kW)
 Continuous hydrostatic transmission for all winches
 Pneumatically operated radial clutches on the skyline /
mainline drum
Brakes:
Skyline
2 hydraulically actuated spring-applied
disk brakes
Mainline
pneumatically actuated spring-applied
band brake
Haulbackline hydraulically actuated spring-applied
multi-disk brake
Straw line
hydraulically actuated spring-applied
multi-disk brake
Operation:
 KollerMultiMatik by operator console
 Radio control for auxiliary functions
Carriage:
SKA 2,5-Z / USKA 2,5 / MSK 4 / MSK 10
Total weight including lines:
Trailer for uphill logging: 28,700 lbs / 13.000 kg
Trailer for up and downhill logging: 32,600 lbs /14.800 kg
Add. Weight – tool boxes (optional): 660 lbs / 300 kg
Add. Weight – powered axle (optional): 2,000 lbs / 900 kg
Add. Weight – foldable tower (optional): 660 lbs / 300 kg
Add. Weight – tower extension (optional): up to 620 lbs / 280 kg
Add. Weight – telescopic tower (optional): 1,100 lbs / 500 kg
NE
W
K 602H w i th tel escopi c tower
K 602H w i th hydraul i cal l y fol dabl e tower
w w w . k o l l e r g m b h . c o m
K 307 GH Mountain Harvester
Truck mounted yarder - for uphill and downhill logging, with crane and processor head
NE
W
The K307GH Mountain harvester is a compact tower yarder for uphill and downhill logging with an optional haulbackline drum.
It is principally used for thinning and selective cuts, but it can also be used for general wood harvesting operations. A 3- oder
4-axle truck with special reinforced frames is used as a carrier.
 4 hydraulically powered guyline winches – operated by radio control
 Skyline spooling guided by hydraulic cylinder
 Large dimension, maintenance-free, pneumatic actuated radial air clutches
T E C H N I C A L
Line pull:
Skyline
Mainline
Haulbackline
Line capacity:
Skyline
Mainline
Haulbackline
Straw line
Guyline
Line speed:
Mainline
Unloaded drive
Loaded drive
Haulbackline
Unloaded drive
Loaded drive
Tower:
Standard
Operating range
D A T A :
14,330 lbs / 65 kN (tension section)
5,510 lbs / 25 kN (average drum)
5,280 lbs / 24 kN (average drum)
2800’ Ø 5/8” /
840 m Ø 16 mm swaged
2500’ Ø 3/8” /
840 m Ø 9 mm swaged
5400’ Ø 3/8” /
1850 m Ø 9 mm swaged
6800’ Ø 3/16” / 1900 m Ø 5 mm
4x160’ Ø 5/8” / 4x50 m Ø 16 mm
2x30’ / 2x10 m extensions
K 307GH 4-axl e tr uck for up and dow nhi l l l ogging
up to 2100 ft/min / 640 m/min
up to 1150 ft/min / 350 m/min
up to 1540 ft/min / 470 m/min
up to 1050 ft/min / 320 m/min
34’ / 10,5 m
360°
Power station:
 Truck diesel engine with 434 HP (324 kW) for example
 Utilization of the direct auxiliary drive
(gearbox independent) – so the full engine power can
be used without any transmission problems
 Continuous hydrostatic transmission for all winches
 Pneumatically operated radial clutches on the
skyline / mainline drum
Brakes:
Skyline
hydraulically actuated
disk brake
Mainline
hydraulically actuated
band brake
Haulbackline hydraulically actuated
multi-disk brake
Straw line
hydraulically actuated
multi-disk brake
spring-applied
spring-applied
spring-applied
spring-applied
Operation:
 KollerMultiMatik and operator cabin
 Radio control for auxiliary functions
Carriage:
SKA 1-Z / USKA 1,5
Total weight including lines:
On a 3-axle truck for uphill logging: 61,700 lbs / 28.000 kg
On a 4-axle truck for up and downhill logging:
70,500 lbs / 32.000 kg
K 307GH 3-axl e tr uck for uphi l l l oggi ng
w w w . k o l l e r g m b h . c o m
7
K 507 GH Mountain Harvester
Truck mounted yarder - for uphill and downhill logging, with crane and processor head
The K507GH is a powerful mountain harvester for uphill, downhill and flat terrain logging.
It is principally used for selective cuts and for general wood harvesting operations. A 8x6 or 8x8 MAN truck with special reinforced
frames is used as a carrier. It has two equivalent winches which can be combined in any order (both possible as mainline or
haulback line). All 4 guylines run inside the tower.
 Comfortable and safe operator cabin
 Skyline drum is equipped with a hydraulic cylinder to aid in drum spooling (radio controlled)
 Hydraulically controlled landing ramps and tiltable truck cab guards optional available (on both sides)
T E C H N I C A L
Line pull:
Skyline
Winch 1 & 2
D A T A :
26,450 lbs / 120 kN (tension section)
9,480 lbs / 43 kN (average drum)
Line capacity:
Skyline
3600’ Ø 3/4” /
1000 m Ø 20 mm swaged
(2550’ Ø 7/8” / 800 m Ø 22 mm swaged)
Winch 1 & 2
5150’ Ø 7/16” /
1600 m Ø 11 mm swaged
(3950’ Ø 1/2” / 1350 m Ø 12 mm swaged)
Straw line
Guyline
5500’ Ø 1/4” / 1700 m Ø 6 mm
4x250’ Ø 3/4” / 4x75 m Ø 20 mm
2x50’ / 2x15 m extensions
Line speed:
Winch 1 & 2
Unloaded drive
Loaded drive
up to 1655 ft/min / 504 m/min
up to 1260 ft/min / 384 m/min
Tower:
Standard
Operating range
34’ / 10,5 m
360°
Power station:
 Truck diesel engine with 434 HP (324 kW) for example
 Utilization of the direct auxiliary drive
(gearbox independent) – so the full engine power can
be used without any transmission problems
 Continuous hydrostatic transmission for all winches
Brakes:
Skyline
Winch 1 & 2
Straw line
hydraulically actuated spring-applied
multi-disk brake
hydraulically actuated spring-applied
multi-disk brake
pneumatically actuated spring-applied
drum brake
Operation:
 KollerMultiMatik and operator cabin
 Radio control for auxiliary functions
Carriage:
USKA 2,5 / MSK 4
Total weight including lines:
On a 4-axle truck: 77,200 lbs / 35.000 kg
8
K 507GH E uro 6 and ai r-condi ti oned cab in
w w w . k o l l e r g m b h . c o m
K 602 GH Mountain Harvester
Truck mounted yarder - for uphill logging, with crane and processor head
The K602GH is a powerful and robust yarder for uphill logging.
It is principally used for selective cuts and for general wood harvesting operations. High speed at maximum tension. A 6x4 or 6x6
MAN truck with special reinforced frames is used as a carrier.
 4 hydraulically powered guyline winches – operated by radio control
 Durable mainline drum constructed with cast steel
 High efficient straight bevel winch gearbox
 Skyline spooling guided by hydraulic cylinder
T E C H N I C A L
Line pull:
Skyline
Mainline
D A T A :
20,940 lbs / 95 kN
11,020 lbs / 50 kN
(tension section)
(average drum)
Line capacity:
Skyline
Mainline
Straw line
Guyline
700 m Ø 13/16” / 2250’ Ø 7/8” /
830 m Ø 20 mm swaged
2100’ Ø 1/2” /
730 m Ø 12 mm swaged
5500’ Ø 1/4” / 1700 m Ø 6 mm
4 or 5x160’ Ø 3/4” /
4 or 5x50 m Ø 20 mm
2x50’ / 2x15 m extensions
Line speed:
Mainline
up to 1960 ft/min / 600 m/min
Tower (depending on country-specific traffic regulations!):
Standard
34’ / 10,5 m
With tower extension possible up to 46’ / 14 m
Foldable tower
34’ / 10,5 m
Telescopic tower
up to 44’ / 13,5 m (two working positions)
Operating range
360°
Power station:
 Truck diesel engine with 473 HP (353 kW)
 Utilization of the direct auxiliary drive
(gearbox independent) – so the full engine power can
be used without excessive transmission wear
 Continuous hydrostatic transmission of all winches
Brakes:
Skyline
Mainline
Straw line
2 hydraulically actuated spring-applied
disk brakes
pneumatically actuated spring-applied
band brake
hydraulically actuated spring-applied
multi-disk brake
K 602GH w i th tower extensi on
NE
W
K 602GH w i th tel escopi c tower
Operation:
 KollerMultiMatik and operator cabin
 Radio control for auxiliary functions
Carriage:
SKA 2,5-Z / MSK 4 / MSK 10
Total weight including lines:
Truck for uphill logging: 68,300 lbs / 31.000 kg
Add. Weight – tower extension (optional): up to 620 lbs / 280 kg
Add. Weight – telescopic tower (optional): 1,100 lbs / 500 kg
K 602GH
w w w . k o l l e r g m b h . c o m
9
K 507 S
Truck mounted yarder - for uphill and downhill logging, as tower yarder only
W
E
N
The K507S is a result of further development of the K507 truck version. This powerful truck mounted yarder was designed to
work with excavator based processor. The shortest truck based yarder of it's class.
 Easy accessibility landed trees by excavator based processor
 Space required similar to trailer mounted yarder
 Skyline spooling guided by hydraulic cylinder
 Total weight less than 57,320 lbs / 26.000 kg
T E C H N I C A L
Line pull:
Skyline
Winch 1 & 2
D A T A :
26,450 lbs / 120 kN (tension section)
9,480 lbs / 43 kN (average drum)
Line capacity:
Skyline
3600’ Ø 3/4” /
1000 m Ø 20 mm swaged
(2550’ Ø 7/8” / 800 m Ø 22 mm swaged)
Winch 1 & 2
5150’ Ø 7/16” /
1600 m Ø 11 mm swaged
(3950’ Ø 1/2” / 1350 m Ø 12 mm swaged)
Straw line
Guyline
5500’ Ø 1/4” / 1700 m Ø 6 mm
4x250’ Ø 3/4” / 4x75 m Ø 20 mm
2x50’ / 2x15 m extensions
Line speed:
Winch 1 & 2
Unloaded drive
Loaded drive
up to 1655 ft/min / 504 m/min
up to 1260 ft/min / 384 m/min
Tower:
Standard
Operating range
39’ / 12 m
360°
Power station:
 Truck diesel engine with 394 HP (294 kW) for example
 Utilization of the direct auxiliary drive
(gearbox independent) – so the full engine power can
be used without any transmission problems
 Continuous hydrostatic transmission for all winches
Brakes:
Skyline
Winch 1 & 2
Straw line
hydraulically actuated spring-applied
multi-disk brake
hydraulically actuated spring-applied
multi-disk brake
pneumatically actuated spring-applied
drum brake
K 507S
Operation:
 KollerMultiMatik by operator console
 Radio control for auxiliary functions
Carriage:
USKA 2,5 / MSK 4
Total weight including lines:
Minimum 54,000 lbs / 24.500 kg
10
w w w . k o l l e r g m b h . c o m
K 602 Power Yarder
Truck or trailer mounted yarder - for uphill logging, automated or manual
The K602 is a powerful yarder for uphill logging. The machine is equipped with a self-supporting frame, allowing a simple
assembly on various trucks or trailers as well as easy worldwide export. It is principally used for selective cuts and for general
wood harvesting operations. The machine is characterized by its robust power transmission and its simple operation.
 Very low fuel consumption - approx. 1 gal/hour (4 litres/hour)
 High speed with heavy loads because of torque-converter and powershift transmission
 Easy maintenance due to its simple construction
 Skyline spooling guided by hydraulic cylinder
T E C H N I C A L
Line pull:
Skyline
Mainline
D A T A :
25,350 lbs / 115 kN (tension section)
14,330 lbs / 65 kN (average drum)
Line capacity:
Skyline
Mainline
Straw line
Guyline
700 m Ø 13/16” / 2250’ Ø 7/8” /
830 m Ø 20 mm swaged
2100’ Ø 1/2” /
730 m Ø 12 mm swaged
4250’ Ø 1/4” / 1500 m Ø 6 mm
4 or 5x160’ Ø 3/4” /
4 or 5x50 m Ø 20 mm
2x50’ / 2x15 m extensions
Line speed:
Mainline
Unloaded drive
Loaded drive
up to 1960 ft/min / 600 m/min
up to 1140 ft/min / 350 m/min
Tower:
Standard
With tower extension
Telescopic tower
Operating range
34’ / 10,5 m
possible up to 46’ / 14 m
up to 44’ / 13,5 m (two working positions)
360°
W
E
N
K 602 Power Yarder automated w i th
K o l l e r M u lt i M at i k
Power station:
 6-cylinder Cummins diesel engine
with 185 HP (138 kW)
 Allison automatic transmission
 Pneumatically operated radial clutches
on the skyline / mainline drum
Brakes:
Skyline
Mainline
Straw line
2 hydraulically actuated spring-applied
disk brakes
pneumatically actuated spring-applied
band brake
hydraulically actuated spring-applied
multi-disk brake
K 602 Power Yarder manual versi on
Operation:
 Manual version: manual control by operator cabin
 Automated version:
KollerMultiMatik and operator cabin
 Empty cycle is done by mainline brake automatically
 Radio control for auxiliary functions
Carriage:
SKA 2,5 / SKA 2,5-Z / MSK 4 / MSK 10
Total weight:
26,500 lbs / 12.000 kg including lines
19,800 lbs / 9.000 kg without lines
Add. Weight – tower extension (optional): up to 620 lbs / 280 kg
Add. Weight – telescopic tower (optional): 1,100 lbs / 500 kg
11
w w w . k o l l e r g m b h . c o m
K 702 Power Yarder
Track, truck or trailer mounted yarder - for uphill and downhill logging
The K702 is the most powerful and fastest Koller yarder for uphill, downhill and flat terrain logging.
The machine is equipped with a self-supporting frame, allowing simple assembly on various trucks and trailers as well as easy
worldwide export. It is principally used for selective cuts and for general wood harvesting operations.
All 4 guylines run inside the tower, they are not disturbing at setup. All guylines are powerd hydraulically.
 Low fuel consumption
 High speed with heavy loads because of converter and powershift transmission
 Easy and low-cost maintenance due to simple construction
 Skyline spooling guided by hydraulic cylinder
T E C H N I C A L
Line Pull:
Skyline
Winch 1 & 2
D A T A :
26,450 lbs / 120 kN (tension section)
17,640 lbs / 80 kN (average drum)
Line capacity:
Skyline
2550’ Ø 7/8” swaged /
800 m Ø 22 mm swaged
(700 m Ø 24 mm)
Winch 1 & 2
Straw line
Guyline
2800’ Ø 9/16” /
900 m Ø 14 mm swaged
5500’ Ø 1/4” / 1700 m Ø 6 mm
4x160’ Ø 7/8” / 4x50 m Ø 22 mm
2x50’ / 2x15 m extensions
Line speed:
Winch 1 & 2
up to 2160 ft/min / 660 m/min
Tower:
Standard
39’ / 12 m
With tower extension 49’ / 15 m
Operating range
left and right side of the vehicle
Power station:
 6-cylinder Cummins diesel engine with 214 HP (160 kW)
 John Deere powershift transmission (3 f / 3 r gears)
 Straight bevel gear transmission with a common
main shaft for both mainline drums
 Stepless hydrostatic transmission
for skyline and straw line
Brakes:
Skyline
Winch 1 & 2
Straw line
K 702 Power S tati on automated w i th
K o l l e r M u lt i M at i k
hydraulically actuated spring-applied
multi-disk brake
pneumatically actuated spring-applied
band brake
pneumatically actuated spring-applied
drum brake
Operation:
 Manual version: manual control by operator cabin
 Automated version:
KollerMultiMatik and operator cabin
 Radio control for auxiliary functions
Carriage:
SKA 2,5 / SKA 2,5-Z / USKA 2,5 / MSK 4
Total weight:
With standard cabin:
24,300 lbs / 11.000 kg without lines
33,100 lbs / 15.000 kg including lines
With comfort cabin & rollover protection:
K 702 track based
(for assembling on a track vehicle)
12
30,900 lbs / 14.000 kg without lines
41,900 lbs / 19.000 kg including lines
K 702 w i th comfor t cabi n
& rol l over protecti on
w w w . k o l l e r g m b h . c o m
Cabin & crane & processor head
Additional equipment
Customer-specific special requests and additional accessories and parts can be provided.
Numerous attachments and options are available.
G E N E R A L
D E S C R I P T I O N:
CABIN:
 Comfort cabin mounted on the side of the crane
 Front and side entry
 Air suspended comfort seat with integrated crane and
winch joysticks
 Temperature-controlled auxiliary heating system
 Air conditioner (optional)
 3 LED working lights and interior light
 Wiper and windscreen washer system on the front door
 Radio with hands-free equipment
 Back window and dormer window for ventilation
 Glazing with bullet-resistant polycarbonate windows on
the area at risk (protection against parts from the
processor chain)
 Certified cabin according to
- FOPS ISO 8083
- OPS ISO 8084
- Bullet resistance rate UL752 Level I
(9 mm Full Metal Jacket)
- Optional also SAE J 1356
CRANE:
 Different models of cranes are available
 Hydraulic power supply specifically sized for the crane
 Cranes up to 200000 ftlbs (270 kNm) lifting moment
and 31’ (9,4 m) operating distance
 Rugged supports
PROCESSOR HEAD:
 Different processor models are available
(Standard: Woody 50 / 60)
 Hydraulic power supply specifically sized for the
processor head
LANDING RAMPS:
 Two hydraulically actuated landing ramps
 Sturdy, anti-slip construction
 Adjustable, sturdy fence elements
TRUCK CAB GUARD:
 Two extendable swiveling and tiltable cab protectors
OTHER OPTIONS:
 Additional diesel fuel tank and fuel transfer pump
 Spooling winch or storage drum for guyline extensions
 Connection voltage 230 V
 Compressed-air connection
 Hydraulic oil filter system for longer maintenance
intervals and longer lifetime
 Bio-degradable hydraulic oil
 Rigging accessories etc. from our large accessory
catalogue
13
w w w . k o l l e r g m b h . c o m
KMM & wireless module & radio control
Operation of KollerMultiMatik, wireless module, & radio control
 Excellent ergonomics
 Durable and long lasting
 Continual product refinement
K
o
l
l
e
r
M
u
l
t
i
M
a
t
i
k
General aspects:
 Radio controlled operation of the yarder unit supported by an innovative display unit
 Electronic synchronized run control for downhill operation
-Stepless single lever operation
-Application area “All-Terrain“
-Electronic regulated line-tension for every operating situation
-Full winch control when moving the carriage (in both directions)
 Fuel efficency caused by electronic control
 Error diagnostics and debugging by GPRS-mobile phone
Display control:
 Operation and control of the machine
 Multiple operating displays (e.g. motor data, operating power, carriage speed and position,
hydraulic oil temperature, fuel level, drive counter, operating hours)
Radio control:
 2 man crew
-Choker-setter controls carriage and winches during breakout
-Yarder operator controls carriage and winches to unload
-Between loading- and unloading point the carriage drives automatically
along the programmed range
-Operator has time for tree processing and choker setter has time to set chokers
 Chokersetter controls yarder and carriage by radio transmitter
 Yarder operator controls yarder and carriage by radio transmitter or
multifunctional joysticks in the cabin
 Stepless hydrostatic transmission for all winches
 1000 m range by radio control (without additional converter)
 Battery operating time up to 1 week
 Four-point channel selection
 Reliable electro-mechanical slackwire protection forworking winches
and straw line
Range programming:
 Display for easy range programming
 Start – Endpoint for slow cruising ranges with different adjustable speeds
 Continuous programmable automatic drive – speed by radio control
 Carriage arrival point changes according to work progress
Rigging functions:
 Freewheel for all winches
 Electronic haulback function for all winches
Safety:
 Cable break protection at carriage with emergency clamping
 Radio control carriage emergency clamping
 Radio controlled skyline emergency drop down
 Adjustable overload shutdown for working winches
 Adjustable maximum pull warning for chocker setter through carriage horn
 Motor and machine control for self-protection of the machine
WIRELESS
MODULE
Display can be transferred by radio module to a slave unit, so that all
KollerMultiMatik-functions are available – reaches up to 330 ft (100 m)
RADIO
14
CONTROL
Separate radio control for auxiliary functions:
guyline drums – brace supports – hydraulic landing ramps…
w w w . k o l l e r g m b h . c o m
Koller Carriages
Carriages for uphill logging
 SKA –The skyline clamping and loadhook release are triggered by reversing the direction of carriage travel (3-6 ft / 1-2 m)
 ZIR –The normal cycling system can be out of order. Tripping time from 3 up to 25 seconds
 Z
–The switching operation of the skyline and mainline clamp can be effected anytime also with reeled-out choker
SKA–1
Skyline
Mainline
Weight
Payload
SKA–1Z
Ø 1/2” – 1” / Ø 12 – 24 mm
Ø 5/16” – 7/16” / Ø 8 – 11 mm
350 lbs / 160 kg (without accessories)
limited by mainline
Skyline
Mainline
Weight
Payload
Ø 1/2” – 1” / Ø 12 – 24 mm
Ø 5/16” – 7/16” / Ø 8 – 11 mm
420 lbs / 190 kg (without accessories)
limited by mainline
 Gravity operation for uphill logging
 Mechanical cycling system still mounted
 Optional with timing system ZIR
 2 skyline pulleys
 Gravity operation for uphill logging
 Mechanical cycling system still mounted
 With radio control and mainline clamp
 2 skyline pulleys
SKA–2,5
SKA–2,5Z
Skyline
Mainline
Weight
Payload
Ø 3/4” – 1 1/8” / Ø 18 – 28 mm
Ø 3/8” – 9/16” / Ø 10 – 14 mm
595 lbs / 270 kg (without accessories)
limited by mainline
 Gravity operation for uphill logging
 Mechanical cycling system still mounted
 Optional with timing system ZIR
 4 skyline pulleys
Skyline
Mainline
Weight
Payload
Ø 3/4” – 1 1/8” / Ø 18 – 28 mm
Ø 3/8” – 9/16” / Ø 10 – 14 mm
680 lbs / 310 kg (without accessories)
limited by mainline
 Gravity operation for uphill logging
 With radio control and mainline clamp
 4 skyline pulleys
w w w . k o l l e r g m b h . c o m
15
Koller Carriages
Carriages for up- and downhill logging
U S K A­– 1 , 5
Skyline
Mainline
Weight
Payload
USKA–2,5Z
Ø 9/16” – 1” / Ø 14 – 24 mm
Ø 3/8” – 7/16” / Ø 9 – 11 mm
760 lbs / 345 kg (without accessories)
limited by mainline
Skyline
Mainline
Weight
Payload
 Slack pulling carriage for up- and downhill operation
 Slack pulling by pulling cable off storage drum
 Radio controlled skyline- and mainline clamp
 Slack pulling distance: 83’ / 70 m with Ø 3/8” / Ø 10 mm
 Radio controlled emergency clamping and
cable break protection
 2 skyline pulleys
MSK–4
Skyline
Mainline
Weight
Payload
16
 Slack pulling carriage for up- and downhill operation
 Slack pulling by pulling cable off storage drum
 Radio controlled skyline- and mainline clamp
 Slack pulling distance: 83’ / 70 m with Ø 3/8” / Ø 10 mm
 Radio controlled emergency clamping and
cable break protection
 4 skyline pulleys
W
E
N
Ø 3/4” – 1 1/4” / Ø 18 – 32 mm
Ø 3/8” – 9/16” / Ø 10 – 14 mm
1750 lbs / 795 kg (without accessories)
limited by mainline
 Proven and improved technology of MSK–3
 Intermediate supports traversable from different
manufacturers
 Motorized slack pulling carriage for up- and
downhill operation
 Slack pulling force up to 1365 lbs (620 kg)
 2 different speeds around 2.6 and 3.9 ft/sec (ca. 0,8 und 1,2 m/s)
Ø 3/4” – 1 1/8” / Ø 18 – 28 mm
Ø 3/8” – 9/16” / Ø 10 – 14 mm
790 lbs / 360 kg (without accessories)
limited by mainline
Wyssen com pat i bl e
safety gate
 Power station by 7.4 HP (5,5 kW) diesel engine
 Radio controlled skyline- and mainline clamp
 Radio controlled emergency clamping and cable break
protection
 4 skyline pulleys
 Unlimited slack pulling length
 Haulbackline has no damage, it´s just fixed at the
backside of the carriage by a shackle
 Radio controlled engine start-stop
 Sideways swing in skyline clamp
 Improved safety gate
 Clutch system with mit brake function
w w w . k o l l e r g m b h . c o m
Koller Carriages
Slack puller for uphill logging
MSK–10
Skyline
Mainline
Weight
Payload
Ø 3/4” – 1” / Ø 18 – 25 mm
Ø 3/8” – 5/8” / Ø 10 – 16 mm
1320 lbs / 600 kg (without accessories)
limited by mainline
 Engine slack puller for uphill logging
 Slack pulling force up to 550 lbs (250 kg)
 Speed around 3.9 ft/sec (1,2 m/sec)
 Power station by 10.3 HP (7,7 kW) diesel engine
 Radio controlled skyline- and mainline clamp
 Active hydraulic clamp for the skyline
 2 skyline pulleys
 Unlimited slack pulling length
 Radio controlled engine start-stop
17
w w w . k o l l e r g m b h . c o m
Accessories
NE
Mechanical felling wedge
W
The felling of the treetops is now much safer due to a vibration-free and simple operation. The felling
wedge is characterized by its small size and light weight.
A simple take away of the wedge is made possible by hooking the felling wedge on the belt (only with the
foldable ratchet possible). Your hands are free for other tools.
Another advantage is the direction of rotation of the spindle. The actuation occurs counterclockwise.
The worker can ergonomically prop up on the tree and operate with his right hand pulling the lever.
Granted patent of utility model!
Koller felling wedge for big trees
Koller felling wedge up to Ø 24” / Ø 60 cm
Unique ergonomic handling and carry. The mechanical
felling wedge is operated using a ratchet.
The lightest and smallest felling of its kind.
When used with large diameter logs, we also recommend a
telescopic ratchet (Item no. V-0800139).
Special burlings at the spreader plate prevent the
coming-out of the chock.
Unique ergonomic handling and carry. The mechanical
felling wedge is operated using a ratchet.
Special burlings at the spreader plate prevent the
coming-out of the chock.
 Item no.
060-024-008
 Item no.
060-025-008
 Net weight
6.5 lbs / 2,95 kg
 Net weight
5 lbs / 2,30 kg
 Foldable ratchet
1.4 lbs / 0,65 kg
 Foldable ratchet
1.4 lbs / 0,65 kg
 Telescopic ratchet optional 2.4 lbs / 1,10 kg
 Total weight
6.5 lbs / 2,95 kg
 Total weight
7.9 lbs / 3,60 kg
 Length/width/height
13.78/3.74/3.35 in
350/95/85 mm
 Length/width/height
13.78/2.56/3.35 in
350/65/85 mm
 Drive per revolution
0.098 in / 2,5 mm
 Drive per revolution
0.098 in / 2,5 mm
 Lever length
12.2 in / 310 mm
 Lever length
12.2 in / 310 mm
 Lift per turn
0.04 in / 1,0 mm
 Lift per turn
0.04 in / 1,0 mm
 Max. lift
1.38 in / 35 mm
 Max. lift
1.38 in / 35 mm
 Max. lifting force
33,070 lbs / 15 t
 Max. lifting force
44,100 lbs / 20 t
 Wood thickness
medium trees
 Wood thickness
big trees
18
w w w . k o l l e r g m b h . c o m
Accessories
Extract from our accessories program
Tailspar Block E2
Wire rope cutter C16
Choker with ring
Wedge clamps
You can find the whole
range of products in
our new webshop!
http://shop.kollergmbh.com
Swivel
High performance block
Kunstfaserseil Samson (Dyneema)
Multistamp anchor
Tree climbing spurs
Length measuring counter
Tracing instrument
Safety belt
Straw line block
Radio controlled chokers
Intermediate supports
Skyline clamps
Mainline blocks
Rigging blocks
Cable tensioner
Cable hoists
Communication systems
Tree climbing spurs
Tracing instrument
Clinometer
Cable tensioning clamps
Wedge clamps
Polyester straps
Chokers
Skylines
Mainlines
Reels for wire rope
Ackja winch
Splicing tools
Steel cables
Intermediate support TS 1
w w w . k o l l e r g m b h . c o m
19
The quality of our products
is the result of 55 years
of experience and
continuous product
development.
We can assure very
high productivity and
excellent resale value
through combining the
use of reliable, high
quality components
with the technical
experience of our
employees.
20
KOLLER GmbH
Kufsteiner Wald 26
A-6334 Schwoich bei Kufstein/Austria
Phone0043-5372-63257
Fax 0043-5372-63257-7
E-Mail: office@kollergmbh.com
Homepage: www.kollergmbh.com
We reserve the right to make changes as technical advances are made.
www.kollergmbh.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising