PT IP Camera
Network Camera User’s Manual
WCS-6020 / WCS-6050
PT Network Camera,
2/5-Megapixel, 150Mbps 802.11b/g/n,
Day & Night, IR LEDs
User Manual
Version 1.0
1/54
Network Camera User’s Manual
Table of Contents
Overview ............................................................................................................... 3
Package Contents................................................................................................. 4
Hardware Description ........................................................................................... 5
Hardware Installation ............................................................................................ 7
Connect to the Network Camera ......................................................................... 10
Recording Software ............................................................................................ 17
Browser-based Viewer Introduction .................................................................... 18
Main Screen with Camera View ................................................................... 18
Client Setting ............................................................................................... 21
Definitions in Configuration ................................................................................. 23
System parameters ...................................................................................... 23
User Management ....................................................................................... 25
Network ....................................................................................................... 27
Access list .................................................................................................... 31
Audio and Video setting ............................................................................... 32
Video record ................................................................................................ 34
Stream ......................................................................................................... 36
Camera control ............................................................................................ 38
Application ................................................................................................... 40
Storage ........................................................................................................ 43
Syslog .......................................................................................................... 44
Status and Parameters ................................................................................ 45
Maintenance ................................................................................................ 46
Appendix ............................................................................................................. 48
A. Troubleshooting & Frequently Asked Questions ...................................... 48
B. Technical specifications ........................................................................... 53
Default Settings
IP Address
Username
Password
DHCP
root
2/54
Network Camera User’s Manual
Overview
The LevelOne WCS-6020 / WCS-6050 is a quality yet cost-effective surveillance
solution for the home and office. It is designed for easy and flexible installation,
provides a choice of either a 150Mbps wireless or wired connection and a WPS
(Wi-Fi protected setup) button to secure the wireless connection with just the
push of a button, and the motorized Pan and Tilt provides a viewing angle of
±355° pan and ±135° tilt. Equipped with a 2/5-Megapixel sensor and built-in IR
cut filter/IR illuminator LEDs, the camera provides high resolution quality and
sharp sensitivity – ideal for security applications both day and night.
The WCS-6020 is equipped with many advanced features such as Level1DNS™
Service, DI/DO for external alarm and sensor, a SD/SDHC card slot and USB
interface for local storage, built-in microphone and external speaker for 2-way
audio communications. Moreover, users can also set up 16 motion-detection
regions with the camera, each with adjustable size and sensitivity. When motion
is detected at the specified regions, the system can send an E-mail alert or send
captured images via FTP upload to a designated storage server. The WCS-6020
is indisputably the top choice for reliable and high performance surveillance.
Law in your country may prohibit the use of surveillance devices. The Network
Camera is not only a high-performance web-ready camera but also can be part
of a flexible surveillance system. It is the user’s responsibility to ensure that the
operation of such devices is legal before installing this unit for its intended use.
Minimum System Requirement
Personal Computer
Operating System
Web Browser
Network Card
Viewer
· CPU: Intel® Celeron® Dual-Core @2.70GHz or above
· Memory Size: 2 GB or above recommended
· VGA card resolution: 1024 x 768 or above
· Windows XP/ Windows 7
· Microsoft Internet Explorer 6.0 or later
· Firefox
· Chrome
· 10Base-T (10 Mbps) or 100Base-TX (100 Mbps) operation
· ActiveX control plug-in for Microsoft IE
3/54
Network Camera User’s Manual
Package Contents







Wireless Network Camera
Antenna x2
Power Adapter
Camera Stand
LAN Cable
Quick Installation Guide
CD Manual / Utility
If any of the above items are missing, please contact your dealer immediately.
Note: Using a power supply with a different voltage than the one included with
the Network Camera may cause damage and void the warranty for this product.
4/54
Network Camera User’s Manual
Hardware Description
1. Light Sensor
Automatically detects lighting condition to turn IR LEDs on/off.
2. Infrared LEDs
There are twelve Infrared (IR) LEDs in front of camera for night vision
purpose. The IR LEDs will auto or manual turn on when the camera is in the
dark environment.
3. Built-in Microphone
The camera has a built-in internal microphone. This microphone is hidden in
the pinhole located on the head of camera.
4. Front LEDs
Red LED indicates power, red LED will turn on always after plug-in power.
Green LED indicates networking, green LED will blink every second after
getting IP address.
Upon powering up, two of front LEDs will become lighted then the camera will
do self-rotation. During the self-rotation, red LED will be on and the network
camera is standing by for getting an IP address.
5. Ethernet Port
Beside the DC power Jack, the LAN socket is an RJ-45 connector for
connections to 10Base-T or 100Base-TX Fast Ethernet cabling. Please use a
Cat 5 “straight through” cable to connect the Network Camera to an Ethernet
network switch or hub.
5/54
Network Camera User’s Manual
6. General I/O Terminal Black
Used for connecting to external input/output devices like alarms or sensors.
7. Line Output
The Network Camera supports two way audio communication so that
operators can transmit and receive audio simultaneously. By using the
Network Camera’s built-in or external microphone and an external speaker,
you can communicate with people around the Network Camera.
8. SD/SDHC Card Slot
The SD/SDHC card slot offers a convenient and portable storage
(snapshots and video clips) option to prevent data loss in case of network
disconnection.
9. Microphone/Line In
The Network Camera supports two way audio communication so that
operators can transmit and receive audio simultaneously. By using the
Network Camera’s built-in or external microphone and an external speaker,
you can communicate with people around the Network Camera.
10. DC Power Jack
The input power is 12VDC. Note that supply the power to the Network
Camera with standard power adapter included in package. Otherwise, the
improper power adapter may damage the unit and result in danger.
11. WiFi Protected Setup (WPS) Button
WPS button for easily establishing a secured wireless connection.
12. USB Port
The USB slot offers a convenient and portable storage (snapshots and video
clips) option to prevent data loss in case of network disconnection.
6/54
Network Camera User’s Manual
Hardware Installation
1. Attach the Network Camera with the included stand
2. Place the Camera on the table or fix it onto ceiling or wall
Use screws to fix the Network Camera onto the ceiling or wall. You could also
place the Network Camera on the table directly.
3. Plug a RJ-45 Ethernet cable into the Network Camera
Connect an Ethernet cable to the LAN socket located on the rear of network
camera and connect it to a network.
Ethernet
Cable Socket
7/54
Network Camera User’s Manual
4. Connect the external power supply to the network camera
Connect the attached power adapter to the DC power jack of the Network
Camera. Note: Use the power adapter, 12VDC, included in the package and
connect it to wall outlet for AC power.
Power
Socket
Once you have installed the Network Camera well and powered on, the camera
will do self-rotation and then the red LED will turn on and green LED will flash
every second. It means that the system is booting
5. General I/O Terminal Block
1: Power
2: Digital output
3. Digital input
4. Ground
If you have external devices such as sensors and alarms, connect it to the I/O
terminal block.
8/54
Network Camera User’s Manual
9/54
Network Camera User’s Manual
Connect to the Network Camera
When you installed your Network camera on your LAN environment, you may install “IP
Finder” to discover Network camera’s IP address. The Administrator must place the
product software CD into the CD-ROM drive of the PC running in Microsoft Windows. An
auto-run program will pop up (If the program is not on auto-run, go to the root directory
of the software CD and click on “autorun.exe”).
Click on “Software Utility” item, after the window contents changed, click on “Install IP
Finder” to run “IP Finder” program.
10/54
Network Camera User’s Manual
“IP Finder” is used to search the IP address of Network Cameras or Video
servers on a LAN. After searching, Video Servers or Network Cameras will be
located by the IP Finder.
11/54
Network Camera User’s Manual
Search Camera
Click search Camera button, The program will search for all family network
devices on the same LAN. After searching, the main installer window will pop up.
Click on the MAC and model name which matches the product label on your
device to connect to the Network Camera via Internet Explorer.
12/54
Network Camera User’s Manual
Setup Camera
Auto Install Wizard will be started and that it can auto guide through the
installation process. Press the “Next” button execute next process. For more
information, please refer to the Network section on page 33.
13/54
Network Camera User’s Manual
14/54
Network Camera User’s Manual
15/54
Network Camera User’s Manual
16/54
Network Camera User’s Manual
Recording Software
The product software CD also contains recording software- IP CamSecure, allowing
simultaneous monitoring and video recording for multiple network cameras. Please
install the recording software; then launch the program to add the Network Camera to
the Channel list. For detailed information about how to use IP CamSecure, please refer
to the user’s manual of the software or download it at http://global.level1.com.
17/54
Network Camera User’s Manual
Browser-based Viewer Introduction
Main Screen with Camera View
3
2
1
The main page has three parts:
1. Configuration functions: The camera can be configured using these user
interfaces.
2. Pan/Tilt & connection control buttons: These buttons provide the direction
to control the pan and tile of camera.
3. Camera View: What the camera sees.
Configuration functions:
ePTZ Settings: Electronic pan/tilt/zoom capabilities that enable users to move to
a target region instantly for close-up shots by simply clicking on the video feeds
on their screen rather than moving the camera physically.
Client Settings: Clicking on this button links you to the client setting page.
Configuration: Please note that only the administrator can access it.
Language: Click this button to choose a language for the user interface.
Note: ePTZ function is only available under image size of 1280x800
18/54
Network Camera User’s Manual
Camera View:
1.
Click this button to capture and save still images. The captured images
will be displayed in a pop-up window. Right-click the image and choose “Save
Picture As” to save it in JPEG format.
2.
This button lets you open a digital zoom, and to control the window to
enlarge a specified area in the camera view.
3.
Click this button to switch to full screen mode. Press the “Esc” key to
switch back to normal mode.
4.
Click on this button to pause/play the video.
5.
Click on this button stop video output.
6.
Click on this button to adjust the audio volume.
7.
Click on this button to toggle mute On/Off.
8.
Click on this button to toggle 2-way audio on/off. Enabling this function
requires an external speaker connected. The server can play sound from the
client and receive sound from the environment and send to client.
9.
Once the Administrator has determined the preset
positions; the User can aim the camera using this control.
19/54
Network Camera User’s Manual
Pan/Tilt & connection control buttons:
1. Connection: User can choose Remote or
Local mode for best connection quality.
2. Video Stream: User can choose stream1 or
stream2.
3. Digital Output: Clicking on the “On” or “Off”
button turns the digital output to either on or off
status.
4. Control Buttons: “Left”, “Right”, “Up”,
“Down”, “Cross Angles”, and “Home”. Camera
returns to center when click “Home” button
5. Pan Angle: User can choose the angles when
the camera moves left and right each time.
6. Tilt Angle: User can choose the angles when
the camera moves up and down each time.
7. Pan: The camera will move from right side to
left side continuously when click the button.
8. Stop: User can stop the movement of camera,
such as Auto pan, Auto Patrol, and etc., by
clicking the button.
9. Patrol: The button directs the camera to patrol
among the preset positions in the patrol list,
which can be modified on the “Camera control
page”. The cycle of patrol is from 1 to 5.
20/54
Network Camera User’s Manual
Client Setting
1. Video output setting: Set video output format.
- Stream: Select use multiple stream video.
- Picture: Select use serial video picture.
2. Internet Protocol Options: Set internet protocol.
- UDP: Select to use UDP protocol.
- TCP: Select to use TCP protocol.
- HTTP: Select to use HTTP protocol.
3. Intranet Protocol Options: Set intranet protocol.
- UDP: Select to use UDP protocol.
- TCP: Select to use TCP protocol.
- HTTP: Select to use HTTP protocol.
NOTE:Protocol options allow choices on the connection protocol between client
and server. There are three protocols choices to optimize your usage – UDP, TCP,
HTTP.
The UDP protocol allows for more real-time audio and video streams. However,
some packets may be lost due to network burst traffic and images may be
obscured.
21/54
Network Camera User’s Manual
The HTTP protocol allows for less packet loss and produces a more accurate
video display. The downside with this protocol is that the real-time effect is worse
than that with the UDP protocol.
The TCP guarantees the complete delivery of streaming data and thus provides
better video quality. However, the real-time effect is not as good as that of the
UDP protocol.
If no special need is required, UDP protocol is recommended. Generally
speaking, the client choice will be in the order of UDP → HTTP. After the
Network Camera is connected successfully, “Protocol Option” will indicate the
selected protocol. The selected protocol will be recorded in the user's PC and will
be used for the next connection. If the network environment is changed, or the
user wants to let the web browser to detect again, manually select the UDP and
TCP protocol, save, and return HOME to re-connect.
22/54
Network Camera User’s Manual
Definitions in Configuration
Please note that only the Administrator can access the system configuration. Each
category in the left column will be explained on the following pages.
System parameters
Firmware version
1. General Setting
(1) Host name
The text displays the title on the top of the main page.
(2) LED indicator
Select turn on or turn off the led indicator.
23/54
Network Camera User’s Manual
2. Time Setting
(1) Time zone
Choose a time zone from the pull down menu.
(2) Daylight saving
Enable or disable daylight saving time.
(3) Current Time
Set the time of the network camera.
(A) Keep current date time
Click on this to keep the current date and time of the network camera. An
internal real-time clock maintains the date and time even when the power of
the system is turned off.
(B) Sync with PC
Synchronize the dat/ time of the network camera with the local computer.
(C) Manually set the time
Adjust the date and time manually.
(D) Adjust by NTP server
Synchronize the time according to NTP server over the Internet whenever
the Network Camera is switched on. It fails if the assigned time-server
cannot be found.
(a) NTP server: Assign the IP address or domain name of the time-server.
Leaving the text box blank connects the Network Camera to the default
time server.
(b) Update interval: Select 0 ~ 23 hours update with the time on the NTP
server.
3. DI and Do Setting
Select Open or Ground to define the DO active state.
Remember to click on “Finish” to immediately validate the changes. Otherwise,
the correct time will not be synchronized.
24/54
Network Camera User’s Manual
User Management
Security setting
The administrator account name is “root”, which is permanent and can not be
deleted. If you want to add more accounts in the Manage User column, please
set a password for the “root” account first. The network camera can provide up to
twenty accounts.
1. Change root password:
Change the Administrator’s password by typing in the new password identically in
both text boxes. The typed entries will be displayed as asterisks for security
purposes. After pressing “finish”, the web browser will ask the Administrator for
the new password to access.
2. Manage privilege
You can modify the manage privilege of operators or viewers. Check or uncheck
the item, then click finish to enable the settings.
25/54
Network Camera User’s Manual
3. Manage user
(1) Add a new user: Administrators can add up to 20 user accounts.
(A) Input the new user’s name and password.
(B) Select the privilege level for the new user account. Click Finish to
enable the setting.
(2) Delete a user: Select an existing user name. Click Finish to enable the
setting.
(3) Update a existing user: Select an existing user name. Administrators can
modify user’s password and privilege. Click Finish to enable the setting.
Access rights are sorted by user privilege (Administrator, Operator, and Viewer).
Only administrators can access the Configuration page. Operators cannot access
the Configuration page but can use the URL Commands to get and set the value
of parameters. Viewers access only the main page for live viewing.
26/54
Network Camera User’s Manual
Network
Any changes made on this page will restart the system in order to validate the
changes. Make sure every field is entered correctly before clicking on “Finish”
Network Setting
LAN / PPPoE / WIRELESS LAN
The default setting is LAN. Select PPPoE if using ADSL dialup.
1. LAN
The default status is Get IP address automatically. This could be tedious to
perform software installation whenever the Network Camera starts. Therefore,
once the network is set, the IP address should be entered correctly. Select Use
fixed IP address then the Network Camera will skip installation. The Network
Camera will automatically restart and operate normally after a power outage. You
can run CamFinder to check the IP address assigned to the Network Camera if
the IP address is forgotten, or you can use the UPnP function provided by the
Network Camera.
27/54
Network Camera User’s Manual
(1) Get IP address automatically
(2) Use fixed IP address
- IP address: This is necessary for network identification.
- Subnet mask: This is used to determine if the destination is in the same
subnet. The default value is “255.255.255.0”.
- Default router: This is a gateway used to forward frames to destinations
in a different subnet. Invalid router setting will fail the transmission to
destinations in different subnet.
- Primary DNS: The primary domain name server that translates
hostnames into IP addresses.
- Secondary DNS: Secondary domain name server backups the Primary
DNS.
- Enable UPnP presentation & port forwarding: Enable UPnP function.
- Http port: This can be typed besides the default Port 80. Once the port is
changed, users must make sure the change for the connection is successful.
For instance, when the Administrator changes the HTTP port of the Network
Camera which IP address is 192.168.0.20 from 80 or 1025 to 65535, the
users must type in the web browser “http://192.168.0.20:8080” instead of
http://192.168.0.20.
- RTSP Port: RTSP port can be typed besides the default Port 554.
- RTP Port: The RTP port can be typed besides the default Port 54.
Note: Please set Video RTP port in even number after default value port 54.
Then, Video RTCP port, Audio RTP port、Audio RTCP port will
automatically set the values in ascending.
- RTSP Streaming access names: The RTSP streaming currently
supports video only, audio only, and audio/video. To use the audio/video
stream, type the URL as“rtsp://61.30.125.43/liveN.sdp”.
2. PPPoE
If using the PPPoE interface, you should fill the following settings from ISP.
(1) User name: The login name of PPPoE account
(2) Password: The password of PPPoE account
(3) Confirm password: Input password again for confirmation
3. WIRELESS LAN
SSID (Service Set Identifier), it is to identify a wireless network. Access Points
and wireless clients attempting to connect to a specific WLAN (Wireless Local
Area Network) must use the same SSID. The default setting is default. Note: The
maximum length of SSID is 32 single-byte characters and SSID can’t be any of “,
<, > and space character.
Wireless mode Click the down arrow to select one from options
1. Infrastructure: The Network Camera connects to the WLAN via an Access
Point. (The default setting)
(1) TX rate: This field is for selecting the maximum transmission rate on the
network. The default setting is “auto”. It means the Network Camera will try
28/54
Network Camera User’s Manual
to connect to the wireless device with the highest transmitting rate.
(2) Security: Select the data encryption method
- None: Do not use data encryption.
- WEP: Allows communication only with other devices which are with
identical WEP settings.
- WPA-PSK: Use WPA pre-shared key.
- WPA2-PSK: Use WPA2 pre-shared key.
(3) Auth Mode: Choosing one of the following modes, (Default setting is
OPEN).
- Open: communicates the key across the network.
- Shared: allows communication only with other devices with identical
WEP settings.
(4) Key length: The administrator can select the key length of 64 or 128 bits.
64 bits is the default setting.
(5) Key format: Choose one of the following formats. HEX is the default
setting.
- HEX digits consist of the numbers 0~9 and the letters A-F.
- ASCII is a code for representing English letters as numbers from
0-127 except “, <, > and space characters that are reserved.
(6) Network Key: Enter a key in either hexadecimal or ASCII format. When
selecting different key length, acceptable input length is listed as following:
64 bits key length: 10 Hex digits or 5 characters.
128 bites key length: 26 Hex digits or 13 characters.
Note: When 22(“), 3C(<) or 3E(>) are input in network key, the key format
can’t be changed to ASCII format.
(7) Algorithm: Choose one of the following algorithms for WPA-PSK modes:
- TKIP
- AES
(8) Pre-shared Key” Enter a key in ASCII format. The length of the key is 8
~ 63
2. Ad-Hoc: Make the Network Camera connect directly to a host equipped
with a wireless adapter in a peer-to-peer environment.
(1) Channel: Under infrastructure mode, the channel will be selected
automatically to match the channel setting for the selected Access Point.
Under Ad-Hoc mode, the channel must be manually set to the same channel
for each wireless adapter. The default channel setting depends on the
installed region.
(2) TX rate: This field is for selecting the maximum transmission rate on the
network. The default setting is “auto”. It means the Network Camera will try
to connect to the other wireless device with highest transmitting rate.
(3) Security: Select the data encrypt method
- None: Do not use data encryption.
- WEP: allows communication only with other devices with identical
WEP settings.
(4) Auth Mode: Choose one of the following modes (Open is the default
29/54
Network Camera User’s Manual
setting).
- Open communicates the key across the network.
- Shared allows communication only with other devices, which are
with identical WEP settings.
(5) Key length: The administrator can select the key length of 64 or 128 bits.
64 bits is the default setting.
(6) Key format: Choose one of the following formats. HEX is the default
setting.
- HEX digits consist of the numbers 0~9 and the letters A-F.
- ASCII is a code for representing English letters as numbers from
0-127 except “, <, > and space characters that are reserved.
(7) Default key/Network Key: Enter a key in either hexadecimal or ASCII
format. When selecting different key length, acceptable input length is listed
as following:
64 bits key length: 10 Hex digits or 5 characters.
128 bites key length: 26 Hex digits or 13 characters.
Note: When 22(“), 3C(<) or 3E(>) are input in network key, the key format
can’t be changed to ASCII format.
DDNS Setting
1. Enable DDNS: This option turns on the DDNS function.
2. Host Name: If the User wants to use DDNS service, this field must be filled.
Please input the hostname that is registered in the DDNS server.
3. E-mail: The E-mail field is necessary for logging in the DDNS server or notify
the User of the new IP address.
4. Register: Click on this button after filling in Host Name and E-mail to register
for DDNS service.
5. Finish: Click on this button to save modified settings for the DDNS service.
30/54
Network Camera User’s Manual
Access list
Access list setting
1. Add denied address: This rule allows the user to assign a range of IP
addresses to the Deny List.
2. Delete denied address: Delete IP address list from the Address List.
31/54
Network Camera User’s Manual
Audio and Video setting
General Setting
1. Color mode: Select use color or monochrome video display.
2. Video orientation: The orientation of video
(1) Flip: Vertically rotate the video.
32/54
Network Camera User’s Manual
(2) Mirror: Horizontally rotates the video.
3. Environment: The orientation of video
(1) Indoor: This option is usually selected when the Network Camera is
placed in indoor environments.
(2) Outdoor: This option is usually selected when the Network Camera is
placed in outdoor environments.
4. Power frequency: Select 50 Hz or 60Hz power line frequency.
※The fluorescent light will flash according to the power line frequency that
depends on local utility. Change the frequency setting to eliminate uncomfortable
flash image when the light source is only fluorescent light.
Video Setting
1. Contrast: Adjust the image contrast level, which ranges from -5 to +5. The
default value is set to 0.
2. Brightness: Adjust the image brightness level, which ranges from -5 to +5.
The default value is set to 0.
3. Saturation: Adjust the image saturation level, which ranges from -5 to +5. The
default value is set to 0.
4. Sharpness: Adjust the image sharpness level, which ranges from -5 to +5.
The default value is set to 0.
5. EV: Exposure value represent the expected target value of the luminance of
the weighting result of AE windows in the image and its tolerance as offset.
6. Gain: In the slide bar of Gain, there are also two sliders, which represent the
limitations to control the maximum gain value and the minimum one, respectively.
Normally, the minimum value is to 1x for better quality.
Infrared Led Setting
1. “Infrared LED Control” IR led for Day and Night (Option). User can turn
on/off the built-in IR led. This function is very useful under low illumination
environment.
(1) Auto: Select IR sensitivity from 0 to 4.
(2) Manual: Turn on/off the IR led manually.
- Turn on: Turn on led
- Turn off: Turn off led
2. Low lux mode: The video quality will be improved when the camera is in low
lux environment.
(1) Disable dark mode: Disable low lux mode.
(2) Enable dark mode: Enable low lux mode.
Audio Setting
1. Mute: Audio mute.
2. Microphone Select: Internal microphone or external microphone select.
3. Mic Volume: Adjust microphone volume, which ranges from 1 to 46. The
default value is set to 40.
33/54
Network Camera User’s Manual
Video record
Schedule mode
(1) Every day: Enable/Disable every day application.
(2) Week day: Enable/Disable week day application.
(3) Selected day: Enable/Disable selected day application.
Schedule information
(1) Enter the Start time and Stop time for day mode.
Note that the time format is [hh:mm] and is expressed in 24-hour clock time.
By default, the start and end time of day mode are set to 01:00:00 and
23:59:59.
(2) Sun/Mon/Tue/Wed/Thu/Fri/Sat: Select the days of the week to perform the
application.
(3) Start day and Start time as the start timing the time. End day and End
time as the end day the time.
(4) Enable cyclic recording: The cyclic recording function is enabled, during
34/54
Network Camera User’s Manual
the transaction stage when a storage space is full and the incoming streaming
data is about to overwrite the previously saved videos.
Record parameters
(1) Source: Select a stream for the recording source.
(2) Recording interval: Select the recording time interval.
(3 )Prefix file name: You can setting the file name, and enable or disable to
add the date and time on file name.
Response mode: There are three choices of server types available: NAS, SD
Card, and USB storage. Select the item to display the detailed configuration
options.
(1)NAS
- NAS server address: Enter IP address of the NAS server.
- NAS shared directory: Enter the NAS shared directory path.
- Workgroup: Enter the NAS workgroup parameter.
- User account: Enter the login name of the NAS account.
- User password: Enter the password of the NAS account.
Note: Video record with the Application must be set to the same shared directory
path. If you would like do detail recording settings or multi-channel recording,
please install the bundled 64-channel Video Management Software in the CD.
35/54
Network Camera User’s Manual
Stream
Audio codec setting
(1) Audio codec type: There are two choices of audio codec types available:
AMR and AAC.
(2) Bit rate
-- AMR The bit rates are selectable at the following rates:
4750,5150,5900,6700,7400,7950,10200 and 12200.
-- AAC The bit rates are selectable at the following rates:
8Kbps, 16Kbps, 24Kbps and 32Kbps.
Video codec setting
(1) Select Stream: The Network Camera supports Stream 1 and Stream 2.
(2) Video codec: User can choose different video compression modes based
36/54
Network Camera User’s Manual
on requirement or application.
(3) Video size: Click the drop down bar to choose the quality of image
(4) Connection type: User can select this button to choose the better video &
links quality. (Internet mode or Intranet mode)
(5) Frame rate: This limits the maximal refresh frame rate per second. Set
the frame rate higher for a smoother video quality.
(6) Intra frame period: Determine how often to plant an “I frame”. The
shorter the duration, the more likely you will get a better video quality, but at
the cost of higher network bandwidth consumption.
(7) Video Quality type: Setting optimizes bandwidth utilization and video
quality.
-- Constant bit rate: User can adjust the video quality manually.
-- Fixed quality: User can select from lowest quality to get best quality
according.
Snapshot and time display setting
Adjust the photo size specifications and choose whether to mark time on the
video and photo.
37/54
Network Camera User’s Manual
Camera control
Camera control
The pan and tilt functions can be controlled with these buttons. The Left button
controls the camera to the left; the Right, Up, and Down buttons control the
camera accordingly.
38/54
Network Camera User’s Manual
(1) UL, UR, LL and LR buttons control the camera to an oblique angle. And
Home button controls the camera to the center.
(2) Pan angle: This sets the range of the horizontal movement of the camera.
The larger value is setting, the larger movement of Left or Right is performed
by the camera.
(3) Tilt angle: This sets the range of the vertical movement of the camera. The
larger value is setting, the larger movement of Up or Down is performed by the
camera.
(4) Patrol cycle: It is the cycle of patrol function.
(5) Auto pan speed: This defines the speed of auto panning. The larger value
is setting, the faster the camera will move.
(6) Auto patrol speed: This defines the speed of auto patrol. The larger value
is setting, the faster the camera will move.
Preset point setting
(1) Set the home position
--Set default value as home position: Restore home position to original
default home by clicking on this button.
--Set the current position as home position: Click on the button will set
the current aimed position as home of the Network Camera. Each time the
Network Camera reboots or finishes calibration, it will automatically aim to
the defined home position
(2) Set the auto pan range
--Set default value as auto pan range: Restore auto pan range to original
default auto pan range by clicking on this button.
--Set the auto pan range manually: Click on the button will set the auto
pan range of the Network Camera.
(3) Add or delete a preset point
--Add current point as a preset point: If the User wants to save the current
view as a preset location, enter a name to each of the current video view on
Preset points and click on the Finish button. The camera allows for 20
preset locations.
--Delete a preset point from below: This keeps a list for preset positions.
Clicking on the Finish button will remove the current selected position from
the preset list.
Patrol list setting
(1) Preset points: The preset points box list all preset points. User must use to
drag the preset points to Patrol list box. When the action is recognized, the
Patrol list box changes to red.
(2) Patrol list: The Patrol list box list all patrol points. Users use the drag to
adjust of the patrol point (Up or down). Dwelling time (sec): The stop time of
each preset location during auto patrols of the Network Camera.
(3) Remove patrol point: The remove patrol point box will remove the patrol
point.
39/54
Network Camera User’s Manual
Application
Schedule mode
(1) Every day: Enable/Disable every day application.
(2) Week day: Enable/Disable week day application.
(3) Selected day: Enable/Disable selected day application.
Schedule information
(1) Enter the Start time and Stop time for day mode.
Note that the time format is [hh:mm:ss] and is expressed in 24-hour clock
time. By default, the start and end time of day mode are set to 01:00:00
and 23:59:59.
(2) Sun/Mon/Tue/Wed/Thu/Fri/Sat: Select the days of the week to perform
the application.
(3) Start day and Start time as the start timing the time. End day and End
time as the end day the time.
40/54
Network Camera User’s Manual
Trigger mode
(1) Video motion detection: Enable/Disable video motion application.
(2) Periodically: This option allows the Network Camera to trigger
periodically for every other defined minute.
(3) Digital input: This option allows the Network Camera to use an external
digital input device or sensor as a trigger source. Depending on your
application, there are many choices of digital input devices on the market
which helps to detect changes in temperature, vibration, sound, and light,
etc.
Parameters
(1) Motion parameters: Higher sensitivity and small threshold will allow
easier motion detection.
(2) Period parameters: This option allows the Network Camera to trigger
periodically for every other defined seconds. Up to 999 seconds are allowed.
(3) Digital input parameters: Select the digital input type and set trigger
time.
Media mode
There are three choices of media types available: Snapshot, Generate digital
output signal, Record (Motion Detection only) and System log.
Snapshot & Record file setting
You can setting the file name, and enable or disable to add the date and time
on file name. Can setting the digital output duration seconds.
Response mode
There are five choices of server types available: Email, FTP, NAS, SD Card,
and USB storage. Select the item to display the detailed configuration options.
(1) Email
-- Email security mode: If your SMTP server requires a secure
connection (SSL or TLS), check this server requires a secure connection
(SSL or TLS).
-- Sender email address: Enter the email address of the sender.
-- Recipient email address: Enter the email address of the recipient.
-- Server address: Enter the domain name or IP address of the email
server.
-- User name: Enter the user name of the email account if necessary.
-- Password: Enter the password of the email account if necessary
-- Server port: The default mail server port is set to 25. You can also
manually set another port.
(2) FTP
-- Server address: Enter the domain name or IP address of the FTP
server.
-- Server port: By default, the FTP server port is set to 21.
-- User name: Enter the login name of the FTP account.
41/54
Network Camera User’s Manual
-- Password: Enter the password of the FTP account.
-- FTP folder name: Enter the folder where the media file will be placed. If
the folder name does not exist, the Network Camera will create one on the
FTP server.
(3) NAS
-- NAS server address: Enter IP address of the NAS server.
-- NAS shared directory: Enter the NAS shared directory path.
-- Workgroup: Enter the NAS workgroup parameter.
-- User account: Enter the login name of the NAS account
-- User password: Enter the password of the NAS account.
Note: Video record with the Application must be set to the same shared directory
path. If you would like do detail recording settings or multi-channel recording,
please install the bundled 64-channel Video Management Software in the CD.
42/54
Network Camera User’s Manual
Storage
Manage the storage device (like SD card or USB flash disk).
Storage Status
Displays the storage device information.
File operation
Move the mouse over the file. Press the mouse right button that Right-click menu
is displayed. You can delete files.
Move the mouse over the directory. Press the mouse left button that the file
structure expand. Press the mouse right button that Right-click menu is displayed.
You can choose upload or delete files.
NOTE:Allow the user to upload or delete files when the storage device is not
write- protected. If the SD card can’t be detected, please link to the following URL:
http://www.sdcard.org/consumers/formatter to download the “SD Formatter Kit”
formatting your SD card.
43/54
Network Camera User’s Manual
Syslog
The Network camera supports log the system messages on remote server.
The protocol is compliant to RFC 3164. If you have external Linux server with sys
log service, use “-r” option to turn on the facility for receiving log from remote
machine. Or you can use some software on Windows that is compliant to RFC
3164. An example is Kiwi Syslog Daemon. Visit
http://www.kiwisyslog.com/kiwi-syslog-daemon-overview/.
Check Setup and Enable then input the IP address and port number of the log
server to enable the remote log facility.
In the Current log, it displays the current system log file. The content of the log
provides useful information about configuration and connection after system
boot-up. Click on Finish to save modify settings.
44/54
Network Camera User’s Manual
Status and Parameters
User can find a lot of information about the system such as Upnp port forwarding,
Traversing NAT, Public IP and so on. User also can get the number of current viewer
of the Network Camera here.
45/54
Network Camera User’s Manual
Maintenance
1. Reboot system: The Reboot button will reboot the Network Camera. It’s
useful while the Network Camera has problems and needs to be rebooted.
2. Restore system: Click on Restore button on the configuration page to
restore the factory default settings. Restore all settings to factory default
except settings in Network type and Root Password. The system will restart
and require the installer program to set up the network again.
3. Calibrate: Recalibrate the home position to the default center to recover the
tolerance cased by some external forces. Please note that there is no
confirming message box after clicking on the Calibrate button. The Network
Camera will calibrate immediately.
4. Upgrade firmware: Select the firmware file and click upgrade button. Please
be aware that you should not turn off the power during updating the firmware
and wait for finish message.
46/54
Network Camera User’s Manual
Warning: The upgrade firmware procedure cannot be interrupted. If the
power and/or network connection are broken during the procedure, it might
possibly cause serious damage to the Network Camera.
Note: When upgrading firmware please wait for 90~180 seconds, and then you
can connect to Network Camera again. The system will restart and require the
installer program to set up the network again.
47/54
Network Camera User’s Manual
Appendix
A. Troubleshooting & Frequently Asked Questions
Q1: Status led does not light up.
A1: First, make sure that「Configuration>System>Turn off the LED indicator」is
disabled. If it is, check the item, and the led should light up. Second, if red led
does not light up, please check that the power adapter in the package is plugged
correctly. And last, if green led does not light up; please check that category 5
UTP cable is plugged correctly.
If the problem is still not solved, please contact your dealer for further help.
Q2: What kind of Ethernet cable is used by network camera?
A2: The network Camera uses Category 5 UTP cable allowing 10 and/or 100
Base-T networking.
Q3: The Network Camera will be installed and work if a firewall exists on
the network?
A3: There are two way to set up the IP camera at Internet.
(1) By UPnP Port Forwarding
1. Select an IP router. It must support UPnP port forwarding and enable this
function first.
2. Connect camera RJ45 cable to IP router and the router is also connected to
Internet.
3. Plug power cord to camera.
4. Go to camera Network page. Enable UPnP port forwarding
5. Check camera status, we can see the ports had been successfully opened.
48/54
Network Camera User’s Manual
6. Type IP address:8080 at browser. Then you can see camera through Internet.
7. You can also type the DDNS name at below label of camera on browser URL
field. For example, you may type user01.C2.mylevel1.com:8080.
(2) By Setting Port Forwarding Manually
1. Select a router. Set the port forwarding as following.
PS. Port 80 is HTTP Port, port 53 is stream port, port 554 is RTSP port. and port
443 is HTTPS port.
49/54
Network Camera User’s Manual
2. Go to camera Network page. Disable UPnP port forwarding function.
3. Type IP address at browser. Then you can see camera through Internet.
4. You can also type the DDNS name at below label of camera on browser URL
field. For example, you may type user01.C2.mylevel1.com.
Note: The firewall software at PC may block the transfer of network camera.
Please remove or stop the kind software.
Q4: What is the default name and password of administrator?
A4: The name is root and the password is <blank>.
Q5: How can I find the network camera in the local area network?
A5: By using the CamFinder program in the CD or using UPnP to find it.
Q6: CamFinder cannot find Network Camera in the local area network at
50/54
Network Camera User’s Manual
first time?
A6: Make sure the subnet of network camera is same as your PC. If the local
area network supports DHCP, the camera is “Get IP address automatically” in
the “Network” page default. If the local area network does not support DHCP,
change your PC IP address to “192.168.0.xxx”.
Q7: How can I restore the network camera to default value?
A7: Use a gem clip to press on the inside button until the led flashing. After three
cycles of the flashing, the network camera begins to restore default value.
Q8: Infrared led does not light up?
A8: Check「Configuration>Audio and Video>Infrared LED Control」 is Auto or
Manual. Turn on.
Q9: The network camera cannot focus accurately.
A9:
(1) The lens is dirty or dust is attached. Clean the lens with lens cleaner. And
then adjust the camera focus manually.
(2) The image may be out of focus. If the object is too near, move the object
away from Network Camera.
Q10: The cover of network camera is warm. Is it normal?
A10: Network camera is a precision device. The internal material has the
operational temperature, and it is normal when user touch the cover feels warm.
It is recommended to put the network camera at aired place and away from any
other device.
Q11: What is the scope of wireless network camera connecting AP?
A11: The scope of wireless connection is different form the environment. The
51/54
Network Camera User’s Manual
possible interference is (1) the direction of antenna (2) the material and
architecture of building (3) the temperature of environment (4) the position of the
network camera.
Q12: The process of upgrade firmware aborted.
A12: Contact your dealer for further help.
Q13: Cannot access the login page and other web pages of Network
Camera from Internet Explorer
A13:
• May be due to the network cable. Try correcting your network cable and
configuration. Test the network interface by connecting a local computer to the
Network Camera via a crossover cable.
• Make sure the Internet connection and setting is ok.
• Make sure enter the IP address of Internet Explorer is correct. If Network
Camera has a dynamic address, it may have changed since you last checked it.
• Network congestion may prevent the web page appearing quickly. Wait for a
while.
The IP address and Subnet Mask of the PC and Network Camera must be in the
same class of the private IP address on the LAN.
• Make sure the http port used by the Network Camera, default=80, is forward to
the Network Camera’s private IP address.
• The port number assigned in your Network Camera might not be available via
Internet. Check your ISP for available port.
• The proxy server may prevent you from connecting directly to Network Camera,
set up not to use the proxy server.
• Confirm that Default Gateway address is correct.
• The router needs Port Forwarding feature. Refer to your router's manual for
details.
• Packet Filtering of the router may prohibit access from an external network.
Refer to your router's manual for details.
• Access Network Camera from the Internet with the global IP address of the
router and port number of Network Camera.
• Some routers reject the global IP address to access Network Camera on the
same LAN. Access with the private IP address and correct port number of
Network Camera.
• When you use DDNS, you need to set Default Gateway and DNS server
address.
• If it’s not working after above procedure, reset Network Camera to default
setting and installed it again.
• Maybe the IP Address of the Network Camera is already being used by another
device or computer.
• If the problem is not solved, the Network Camera might be faulty. Contact your
dealer for further help.
52/54
Network Camera User’s Manual
B. Technical specifications
WCS-6020
WCS-6050
Image Sensor
2-Megapixel 1/2.7" Progressive CMOS
5-Megapixel 1/3.2" Progressive CMOS
Effective Pixels
1920x1080
2560x1920
Camera
Lens
Board lens, fixed-focal, f=4.0 mm, F2.0
62 ゚
Angle of View (H)
Color: 1.5 lux at F2.0
B/W: 1.0 lux at F2.0
Minimum Illumination
IR Cut Filter
Removable infrared-cut filter for day & night function
Shutter Time
1 to 1/10000 sec.
Pan/Tilt/Zoom
Pan range: ±355 ゚(-177.5°~177.5°)
Tilt range: ±135 ゚ (-45°~ 90°)
Auto pan mode
Auto patrol mode
IR LED
12 IR LEDs for illumination up to 10m
Video
Video Compression
H.264 / MPEG4 / MJPEG
H.264 / MJPEG
Resolutions
1080p(1920x1080) / SXGA(1280x1024) /
WXGA(1280x800) / VGA(640x480) /
QVGA(320x240) / QCIF(176x144)
Frame Rate
Up to 30 fps at 1920x1080
Video Streaming
5M(2560x1920) / 1080p(1920x1080) /
SXGA(1280x1024) / WXGA(1280x800) /
VGA(640x480) / QVGA(320x240) /
QCIF(176x144)
Up to 10 fps at 2560x1920
Up to 30 fps at 1920x1080
Multiple simultaneous streams, up to 2 streams
Image Setting
- Adjustable image size, quality and bit rate
- Configurable brightness, sharpness, contrast, saturation, white balance and exposure
- AGC/AWB/AES
- Flip & Mirror
- Time Stamp
Video Format
MPEG4
Audio
Audio Streaming
2-way audio
Audio Compression
G.726 / AMR
Audio Input/Output
Built-in microphone
Mic/line input, line output
Network
10/100 Mbps Ethernet, RJ-45
Built-in 802.11b/g/n WLAN
Networking
Multi-level user access with password protection
IP address filtering
Security
Supported protocols
TCP/IP, HTTP, SMTP, FTP, DDNS, UPnP, Telnet, NTP, PPPoE, DNS, DHCP, RTSP, Samba
Number of clients
20
53/54
Network Camera User’s Manual
DNS
Easy Internet monitoring via configuration free Level1DNS™ service
Wireless
Networking
Built-in 802.11b/g/n WLAN
802.11n: 6.5~72.2/13.5~150Mbps (20/40 MHz)
802.11g: 54 ~ 6 Mbps
802.11b: 11 ~ 1 Mbps
Transfer Rate
Wireless Security
WEP, WPA-PSK, WPA2-PSK
Ch.1 ~ 11 USA
Ch.1 ~ 13 EU
Channels
Operating Frequency
2.412 ~ 2.472GHz
Antenna
2x 2dBi antennas
Alarm and Event Management
Motion Detection
16 Detection Zones
Notification
FTP, SMTP, Samba
DI/DO
1 D/I and 1 D/O for external sensor and alarm
General
Local storage
SD/SDHC card slot, USB slot
Power
DC12V 1.5A
Power Consumption (Max.)
12W
RJ-45 10BASE-T/100BASE-TX
3.5mm line out
3.5mm mic/line in
WPS Button
I/O terminal block (DI/DO)
DC Power Jack
Connectors
LED Indicator
Power/Link
Button
Reset Button
Operating Temperature (°C)
0°C ~ 40°C
Operating Humidity (Non-condensing)
10% to 80%
Dimensions
105 x 105 x 110 mm
Weight
356 g
Approvals
Viewing System Requirements
Bundled Software
CE, FCC, Onvif
OS: Microsoft Windows 7/Vista/XP
Browser: Internet Explorer 6.x or above, Firefox, Chrome, Safari
Cell phone: 3GPP player
Real Player: 10.5 or above
Quick Time 6.5 or above
Bundled with 64-Channel LevelOne management software
54/54
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising