2202412 Comm Stacked Dryer
COMMERCIAL STACKED DRYER
INSTALLATION INSTRUCTIONS
LEAVE THESE INSTRUCTIONS WITH THE OWNER
Printed in U.S.A
2202412
The following caution should be posted near the dryer in a prominent location.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
If you have gas appliances, instructions to be followed in the event the user smells gas should be posted near
the dryer in a prominent location. This information may be obtained by consulting with your local gas supplier.
FOR SAFETY
You should caution users of this product:
●
Not to dry articles containing flammable fumes or materials.
Not to dry articles containing foam rubber.
● Not to permit children to play in, on, with or around this equipment and that children should be
supervised if near at hand when the equipment is in use.
●
FOR BEST PERFORMANCE
Keep area around dryer clean, free of lint and combustibles such as gasoline and other flammable materials
and vapors.
Examine exhaust ducting system regularly during the year to assure proper drying operation.
Make sure dryer lint filter is kept clean to assure proper drying operation
Page 1
Read this before you start…
TOOLS needed for installation
●
●
●
●
●
●
Teflon tape or pipe joint
compound (gas)
Cutting knife
Pipe wrench (gas)
Ratchet
5/16” socket
5/16” nut driver
●
●
●
●
●
●
Level
Screw driver (standard)
Duct tape
Crescent wrench
T20 security torx driver
3/8” deep well socket
(electric – U.S. only)
Proper installation is the responsibility of the purchaser.
SERVICE CALLS PERFORMED AS A RESULT OF POOR INSTALLATION ARE THE RESPONSIBILITY OF
THE INSTALLER.
Make sure you have everything necessary for proper installation.
1.
2.
3.
4.
GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements starting on page 7.
POWER CORDS for electric dryers (except Canada).
GAS LINES (if a gas dryer) must meet National and Local Codes.
EXHAUST SYSTEM – use rigid metal or flexible metal exhaust ducting. See Exhaust Requirements in
this section.
NOTE: Dryer door reversal instructions are on page 13 item 10.
71-15/32
51
38-3/16
39-5/32
39-11/32
15-1/4
3-5/8
3-7/16
3-1/4
13-1/2
20-11/16
3/8” min.
6-13/16➝
➝
➝
➝
2-7/16
27-1/2
27
PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY BEFORE STARTING TO INSTALL THE
DRYER. THESE INSTRUCTIONS SHOULD BE RETAINED FOR FUTURE REFERENCE.
FOR GAS DRYERS THE INSTALLATION MUST CONFORM WITH THE NATIONAL FUEL GAS CODE
ANSI Z223.1, LATEST REVISION. ANY QUESTIONS CONCERNING THIS SHOULD BE REFERRED TO
THE LOCAL GAS UTILITY.
REMOVE THE DOOR FROM ALL DISCARDED DRYERS TO AVOID THE DANGER OF A CHILD
SUFFOCATING.
Page 2
LOCAL CONSIDERATIONS
The dryer should be located to permit adequate room in front for loading the dryer, and sufficient room behind
the dryer for the exhaust system.
This dryer is factory-ready for rear exhaust. To exhaust out the bottom or left side, use an accessory exhaust
kit available from your Commercial Distributor. Instructions are included with the kit.
When installing the dryer the following minimum clearances to combustibles apply; clearance to wall and sides
– 0 inches. Top – 0 inches with outside exhaust; rear – 0 inches with outside exhaust, 6 inches with inside
exhaust. If an inside exhaust is used (not recommended) 8 inches clearance must be maintained above top.
It is important to make sure the room has adequate make-up air. The area where the dryer is located must not
obstruct the flow of combustion or ventilating air. There must be a minimum of 24 square inches of unobstructed
space surrounding each dryer.
On gas dryers, adequate clearance as noted on the data plate must be maintained to insure adequate air for
combustion and proper operation of the dryer.
For gas dryer installations where dry cleaners are installed, the sources of all make-up air and air movement
to the dryers must be located away from dry cleaners.
THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO
WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR AND FREE FROM
COMBUSTIBLE MATERIALS, GASOLINE AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER
PRODUCES COMBUSTIBLE LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT FREE OF LINT.
EXHAUSTING
! WARNING
WARNING –
The dryer must be
exhausted to the
outside to reduce the
risk of fire.
Exhausting the dryer to the outside is
mandatory to prevent large amounts of
moisture and lint from being blown into
the room.
! WARNING
WARNING –
Plastic or nonmetal flexible
duct presents a potential
fire hazard.
NEVER USE PLASTIC
OR NONMETAL
FLEXIBLE DUCT.
If your existing ductwork is plastic, nonmetal or
combustible, replace it with metal. Use only metal
exhaust duct that will not support combustion to
insure the containment of exhaust air, heat and lint.
FOR BEST PERFORMANCE USE A MINIMUM OF 4-INCH DIAMETER RIGID ALUMINUM OR RIGID
GALVANIZED STEEL DUCT. Do not use smaller duct. Ducts larger than 4 inches in diameter can result in
increased lint accumulation. Lint accumulation should be cleaned regularly. If flexible metal duct must be
used, the type with a stiff sheet metal wall is preferred.
Page 3
Exhaust Hood Type
Number
of
90° Turns
4”
2-1/2”
Maximum length of 4-inch diameter
rigid metal duct
0
100 ft.
59 ft.
1
80 ft.
48 ft.
2
65 ft.
38 ft.
3
50 ft.
30 ft.
4
35 ft.
22 ft.
Maximum length of 4-inch diameter
flexible stiff walled metal duct
0
1
2
3
4
36
32
28
25
23
ft.
ft.
ft.
ft.
ft.
28
24
20
17
15
ft.
ft.
ft.
ft.
ft.
For difficult installations requiring a flexible transition, multi-layered thin foil exhaust duct may be used.
Thin foil duct:
●
●
●
●
●
●
●
●
●
●
●
must
must
must
must
must
must
must
must
must
must
must
be the type that is approved for dryer installations by UL or other comparable testing agency.
conform to all applicable codes.
only be used as a transition between the dryer and the wall connection.
not exceed 8 feet in length when stretched.
not interconnect with other thin foil flexible ducts.
be extended to the full length with any excess removed.
be installed only by a qualified and trained commercial dryer installer.
not be placed near sharp objects.
be kept as straight as possible.
not be used inside the dryer.
be inspected regularly to be sure that it has not become crushed or otherwise restricted.
Thin foil duct will reduce airflow resulting in longer drying times. To reduce the negative effect on drying
performance the thin foil ducting:
●
should be shaped such that there are no more than two 90-degree elbows in the foil duct.
should not be used in conjunction with rigid duct runs that are longer than 20 feet.
● should not be used in duct runs that include more than three 90-degree elbows.
● should be supported to minimize sagging.
●
Serious blockage can result in flexible metal duct if bent too sharp. Never install any type of ducting in walls,
ceilings, or other concealed spaces.
Keep exhaust duct as straight and short as possible. Exhaust systems longer than recommended can extend
drying times, affect machine operation and may collect lint. Secure joints with duct tape.
Do not use screws.
Page 4
DO NOT exhaust dryer into any wall, ceiling, crawl space or a concealed space of a building, gas vent,
or any other common duct or chimney. This could create a fire hazard from lint expelled by the dryer.
The exhaust duct should end with an exhaust hood with a swing out damper to prevent backdrafts and entry
of wildlife. NEVER use an exhaust hood with a magnetic damper. The hood should have at least 12 inches of
clearance between the bottom of the hood and the ground or other obstruction. The hood opening should
point down. NEVER install a screen over the exhaust outlet.
When possible, do not exhaust the dryer directly into a window well in order to avoid lint build-up. Do not
exhaust under a house or porch.
If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly down
towards the exhaust hood to reduce condensation and lint build-up.
If an existing exhaust system is to be used with your dryer(s) you must be sure:
●
●
●
●
●
The exhaust system meets all local, state and national codes.
That plastic flexible duct is not used.
To completely inspect and clean all lint accumulating from the interior of the duct.
The duct is not kinked or crushed.
The exhaust hood damper opens and closes freely.
Inspect and clean the interior of the exhaust system at least twice a year. Disconnect electric service prior to
cleaning. Check gas line on gas dryers anytime the dryer is moved.
Frequently check to be sure the exhaust hood damper opens and closes freely.
If multiple units are exhausted into a common duct:
1. An area of 12.57 square inches is required per dryer. This will allow for free air movement should all
dryers be operated simultaneously.
2. A power exhaust may be used on multiple installations.
3. Ducts larger than 4 inches in diameter can result in increased lint accumulation. Lint accumulation
should be cleaned regularly.
4. Exhausting should be kept as short and as direct as possible.
The static pressure in any exhaust system must be between 0 and 0.92 inches of water column. This can be
measured with a manometer at the point where the exhaust duct connects to the dryer. A “no heat” setting
should be used. The dryer tumbler should be empty and the lint filter clean.
Inspect and clean the interior or the exhaust system at least once a year. Disconnect electrical service prior
to cleaning. Check the gas line on gas dryers anytime the dryer is moved.
Frequently check to be sure the exhaust hood damper opens and closes freely.
Page 5
GAS REQUIREMENTS
Use only Natural or LP (liquid propane) gases.
THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES,
WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES),
OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).
Gas dryers are equipped with a burner orifice for operation on NATURAL gas. If the dryer is to be operated
on LP gas, it must be converted for safe and proper performance and must be converted by a qualified
service technician. Conversion kits from NATURAL to LP, or LP to NATURAL are available through your
Commercial Distributor (see Accessories). If other conversions are required, check with the local gas utility for
specific information concerning conversion requirements.
Each dryer will provide an input of 24,000 B.T.U. per hour. The size of the main line will depend on the
number of dryers.
A 1/2” gas supply line is recommended and must be reduced to connect to the 3/8” gas line on the dryer.
The internal gas shut-off is accessed by removing the front panel on the lower dryer and the access panel on
the upper dryer. The shut-off is positioned for easy access near the gas valve.
The National Fuel Gas Code requires that an acceptable, approved manual gas shut off valve be installed
within 6 feet of the dryer.
Additionally, a 1/8” N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge connection, must
be installed immediately upstream of the gas supply connection to the dryer.
The dryer must be disconnected from the gas supply piping system during any pressure testing of the system.
DO NOT re-use old flexible metal gas line. Flexible gas line must be design certified by American Gas
Association (CGA in Canada). NOTE: Any pipe joint compound used must be resistant to the action of any
liquefied petroleum gas.
NOTE: As a courtesy, most local gas utilities will inspect a gas appliance installation.
GAS IGNITION –
These dryers use an automatic ignition system to ignite the burners. There is no constant burning pilot.
●
Improper connection of the equipment-grounding conductor can result in a risk of
electrical shock. Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly grounded.
● Do not modify the plug provided with the appliance – if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
● To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring
and grounding must be done in accordance with the National Electrical Code
ANSI/NFPA, No. 70-Latest Revision (for U.S.) or the Canadian Electrical code
CSA C22.1-Latest Revision (for Canada) and local codes and ordinances. It is
the personal responsibility and obligation of the appliance owner to provide adequate electrical services
for this appliance.
● All gas installations must be done in accordance with the National Fuel Gas Code ANSI/Z223.1-Latest
Revision (for the U.S.) or the CAN/CGA-B149 Installation Codes-Latest Revision (for Canada) and local
codes and ordinances.
! WARNING
Page 6
ELECTRICAL REQUIREMENTS
! WARNING WARNING – To prevent
NOTE: Wiring diagram is located inside the lower cabinet on
the left hand side.
Export models (not U.S. or Canada):
See Additional Instructions for Export Models on the following pages.
GROUNDING
Each dryer must be grounded. In the event of malfunction or
breakdown, the ground will reduce the risk of electrical shock by
providing a path of least resistance for electrical current.
unnecessary risk of fire,
electrical shock or
personal injury, all wiring
and grounding must be
done in accordance
with local codes, with
the National Electrical Code, ANSI/
NFPA (for the United States) or the
Canadian Electrical Code CSA C22.1
(for Canada).
GAS MODELS
Each appliance is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided with the appliance – if it will not fit the
outlet, have a proper outlet installed by a qualified electrician.
If a separate ground is required by local codes, a grounding kit (Part No. 12001875) is available. It contains
ground wire, clamp, ground screw and washer. Connect ground wire to back of unit with the cabinet ground
screw and washer the ground screw and washer. Secure other end of ground wire to a suitable external
ground connection. The wire may be secured with the clamp to a grounded COLD metal water pipe. NEVER
CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES OR HOT WATER PIPES.
ELECTRIC MODELS
If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected to a grounded metal,
permanent wiring system; or an equipment grounding conductor
must be run with the circuit conductors and connected to the
equipment grounding terminal.
U.S. Electric models are shipped with a ground strap connected
from the neutral terminal block post to the frame of each dryer. If
local codes prohibits the use of the ground strap, the dryer must be
grounded in accordance with local codes.
! WARNING WARNING: Improper
connection of the
equipment grounding
conductor can result in a
risk of electric shock.
Check with a qualified
electrician or serviceman if you are in
doubt as to whether the appliance is
properly grounded.
Each electric dryer must be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected
to the equipment grounding terminal.
ELECTRICAL CONNECTIONS
BEFORE OPERATING OR TESTING, follow all grounding instructions in Grounding Section above.
An individual branch (or separate) circuit serving only this appliance is recommended. DO NOT USE AN
EXTENSION CORD.
GAS MODELS – U.S. and Canada
A 120 volt, 60 Hz AC, approved electrical supply, with a 15 ampere fuse or circuit breaker is required.
Page 7
ELECTRIC MODELS – U.S. and Canada
A 120/240 volt, 60 Hz AC approved electrical service fused through a 30 ampere fuse or circuit breaker on both
sides of the line is required.
If a power cord is used, the cord should be plugged into a 30 ampere receptacle.
U.S. ELECTRIC MODELS
The power cord is NOT provided with U.S. electric model dryers.
IMPORTANT: When permitted by local codes, the dryer electrical supply may be connected by means of a
new power supply cord kit, marked for use with clothes dryer, that is U.L. listed, rated at 120/240 volts minimum, 30 amperes with three No. 10 copper wire conductors terminated with closed loop terminals, open-end
spade lugs with turned up ends or with tinned leads.
Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring must be retained
at the dryer cabinet with a suitable UL listed strain relief.
If the dryer is to be installed in an area where local codes do not permit grounding through neutral, only a 4
conductor power cord, rated and terminated as above, may be used.
120/208 Volt Electrical Systems:
For maximum drying performance, a U.S. electric dryer can be converted if it is to operate on a 120/208 volt
electrical system. A heating element conversion kit is available (see Accessories).
CANADIAN ELECTRIC MODELS
All Canadian models are not shipped with the power cord attached.
It is not permissible to convert a dryer in Canada to 208 volts.
Additional Instructions for Export Models
(not U.S. or Canada)
Contact the distributor that sold the appliance or: Maytag International, 1475 East Woodfield Road,
Schaumburg, Illinois USA 60173, 847-273-3100, for information on product, shipping damage, replacement
parts and accessories.
Maytag dryer models manufactured for operation on 60 Hz AC are not designed for use on 50 Hz AC electrical service and conversion of the product from 60 to 50 Hz operation is not recommended. For additional
information on 50 Hz products, contact Maytag International.
The electric service requirements can be found on the data label located on the front of the dryer behind the
door.
EXPORT ELECTRIC MODELS
Export electric models are manufactured for operation on either 230/240 volt, 50 Hz or 220 volt, 60 Hz
approved electric service. A two-wire approved electrical service with a 30 ampere fuse or circuit breaker is
required. The dryer must be properly grounded with a ground wire.
IMPORTANT: When permitted by local codes, the dryer electrical supply may be connected by means of a
new power supply cord kit, marked for use with clothes dryers, that is agency listed, rated at 240 volts minimum, 30 amperes with two No. 10 copper wire conductors terminated with closed loop terminals, open-end
spade lugs with turned up ends or with tinned leads.
Do not reuse a power supply cord from an old dryer. The power cord or electric supply wiring must be
retained at the dryer cabinet with a suitable agency listed strain relief.
Page 8
ADDITIONAL INFORMATION
REPLACEMENT PARTS AND ACCESSORIES
If the dryer requires replacement parts or accessories, contact the Commercial Distributor from whom you
purchased your dryer or:
Maytag Customer Service
240 Edwards Street, S.E.
Cleveland, Tennessee 37311
Phone 615-472-3333, for information on the
nearest authorized Maytag Parts Distributor.
EXPORT MODELS
Contact the Commercial Distributor from whom
you purchased your dryer or:
Maytag International
1475 East Woodfield Road
Schaumburg, Illinois, USA 60173
Phone 847-273-3100, for information on the
nearest authorized Maytag Parts Distributor.
Crate
Nail
To install…
Figure 1
1.
Using a screwdriver, remove the crate
nails securing the wood shipping base to
the bottom of the dryer. (See figure 1.)
2.
Remove the wood base. Loosen the 4
leveling locking nuts and insert four vinyl
feet onto legs. (See figure 2)
3.
Move unit into position, level, tighten the
leveling lock nuts.
Figure 2
Page 9
4.
For gas dryers:
Remove red thread protector and apply pipe joint compound or about 1-1/2 wraps of Teflon tape over threaded
connection on the end of the pipe applying to both dryers.
(See figure 3.)
NOTE: Pipe joint compound must be resistant to the
action of any liquefied petroleum gas.
Remove the red
pipe thread
protective cap.
Add additional fitting to connect the 3/8” gas pipe to a
female threaded end of a 3/4” flexible connector making
sure connection is tight. (See figure. 4)
5.
6.
7.
Connect both dryers to the gas supply.
Open the gas service valve and check all gas supply connections from service valve to shut off valve for leaks using a
soap solution, DO NOT use an open flame to check for
gas leaks. If bubbles occur, tighten the connections and
recheck.
NOTE: As a courtesy, many local gas utilities will inspect a
gas appliance installation. Check with your local utility to
see if this service is provided in your area.
NOTE: The minimum permissible gas (natural or mixed)
supply pressure for purposes of input adjustment is 4.5
inches of water.
Open the gas shut off valve inside the upper dryer
(See figure 5.), and check the union
connection to the gas valve for leaks using a soap
solution, DO NOT use an open flame to check for
gas leaks. If bubbles occur, tighten the connections
and recheck.
NOTE: As a courtesy, many local gas utilities will
inspect a gas appliance installation. Check with your
local utility to see if this service is provided in your
area.
NOTE: The minimum permissible gas (natural or
mixed) supply pressure for purposes of input adjustment is 4.5 inches of water.
For gas dryer, plug in both power cords.
Page 10
Figure 3
Figure 4
Shown with gas
valve open.
Figure 5
8.
For electric dryers:
TO MAKE ELECTRICAL CONNECTION FOR U.S. DRYERS
Review electrical requirements on page 7 of these instructions.
IMPORTANT – All U.S. models are produced for a
3-WIRE SYSTEM CONNECTION. The dryer frame is
grounded to the neutral conductor at the terminal block.
A 4-WIRE SYSTEM CONNECTION is required for new
or remodeled construction, mobile homes, or if local
codes do not permit grounding through neutral. If the
4-wire system is used, the dryer frame cannot be
grounded to the neutral conductor at the terminal block.
Refer to the following instructions for 3- and 4-WIRE
SYSTEM CONNECTIONS.
Remove the terminal block cover plate. (See figure 6.)
Insert the power cord with a U.L. listed strain relief
through the hole provided in the cabinet near the
terminal block. Note, a strain relief must be used.
Terminal Block
Cover Plate
3-WIRE SYSTEM CONNECTIONS
(Refer to figures 7 and 8.)
Figure 6
Do not loosen the nuts already installed on the terminal block.
Be sure they are tight. Use a 3/8” deep well socket.
If the power cord has terminals, place the terminals over the
existing nuts on the posts. The neutral (white or center wire on
Neutral
power cord) conductor must always be connected to the center
Post
(silver colored) post of the terminal block.
Secure in place using the nuts provided in the parts package.
If the power cord does not have terminals, use the cupped
washers ahead of the nuts.
Be sure the terminal block nuts are tight. Secure the power
Terminal
Block
cord in position. Tighten the strain relief screw(s) in order to
Support
clamp the strain relief to the cord.
Replace the terminal block cover.
BEFORE OPERATING OR TESTING, follow the grounding
directions on page 7.
Figure 7
4-WIRE SYSTEM CONNECTIONS
Remove the ground strap screw from the terminal block
support. Fold the ground strap over so both ends of the
ground strap are attached to the center terminal block post.
Connect the neutral (white) conductor of the cord to the center
Neutral
(silver) post of the terminal block. Connect the grounding
Post
(green) wire of the cord to the terminal block support using the
ground strap screw.
Connect the red and black wires of the cord to the outer posts
of the terminal block.
Be sure the terminal block nuts are on tight. Secure the power
cord in position. Tighten the strain relief screw(s) in order to
clamp the strain relief to the cord.
Replace the terminal block cover.
WARNING: If converting from 4-wire electrical systems to
3-wire, the ground strap must be reconnected to terminal block
Figure 8
support to ground the dryer frame to the neutral conductor.
Page 11
3-Wire System
Ground
Strap
Ground
Strap
Screw
Hole for
power
cord
and
strain
relief
3-Wire System
Ground
Strap
Neutral
Strain
relief
2-WIRE AND GROUND SYSTEM CONNECTIONS
2-Wire and Ground System
Remove the terminal block cover plate.
Insert the power cord with an agency listed strain relief
through the hole provided in the cabinet near the terminal
block. Note, a strain relief must be used. (See figure 9.)
Do not loosen the nuts already installed on the terminal
block. Be sure they are tight. Use a 3/8” deep well
socket.
Neutral
Post
Power
Cord
Ground
Wire
Secure the power cord ground wire to the terminal block
support using the ground screw.
If the power cord has terminals, place the terminals over
the existing nuts on the posts. The neutral wire in power
cord must be connected to the center (silver colored)
post of the terminal block.
Power
cord
and
strain
relief
Neutral
Secure in place using the nuts provided in the parts package. If the power cord does not have terminals, use the
cupped washers ahead of the nuts.
Be sure the terminal block nuts are tight. Secure the
power cord in position. Tighten the strain relief screw(s) in Figure 9
order to clamp the strain relief to the cord.
Replace the terminal block cover.
BEFORE OPERATING OR TESTING, be sure the machine is properly grounded.
EXPORT GAS MODELS
Export gas models are manufactured for operation on either 230/240 volt, 50 Hz or 220 volt, 60 Hz AC
approved electrical service with a 15 ampere fuse or circuit breaker.
Export gas models have been manufactured for use with natural gas having a higher heating value of approximately 1025 BTU per cubic foot. Conversion to LP gas with a higher heating value of approximately 2500
BTU per cubic foot must be performed by a qualified service technician. A conversion kit is available.
FOR ALL MODELS
9.
Connect the exhaust ducts to duct work. (See figure 10.)
Figure 10
Page 12
10. The upper and lower dryer door direction can be reversed.
(See figure 11)
1. Remove the 2 hing hole covers by gently prying out with a screw driver.
2. While supporting the door remove the 4 screws in the hinges that secure the hinges to the front
panel.
3. Move the following parts to the opposite side of the door: 2 hinges and 4 screws, 4 door screws,
door strike and screw, inner door cover plate and screw.
4. Attach the door to the opposite side of the front panel using the 4 counter sink screws.
5. Replace the 2 hing hole covers in the opposite side of the front panel.
Door
Screws
Door Catch
Hinge
Door
Strike
Hinge
Hole
Cover
Inner Door
Cover Plate
Door
Screws
Figure 11
11. For MN models, remove dial skirts, knobs, nuts and caps from miscellaneous parts package.
Insert
each dial skirt onto each timer shaft, the long shaft pin will orient the skirt correctly. Insert knob onto
shaft and secure with the nut. Snap cap into knob. (See figure 12.)
12. Make sure all gas, exhaust and electrical connections are complete.
Plug dryer in, and check operation
by using the check list below.
13. (GAS MODELS ONLY)
The burner may not ignite initially due to air in the gas line. Allowing the dryer to operate on a heat
setting will purge the line. If the gas does not ignite within five minutes, turn the dryer off and wait
5 minutes. Be sure the gas supply to the dryer has been turned on. In order to confirm gas ignition,
check the exhaust for heat.
14. Remove tape from each corner of the front panel.
Figure 12
Dial Skirt
Knob
Nut
Cap
Long Shaft Pin
Timer Shaft
Page 13
FINAL INSTALLATION
CHECK LIST
COMMERCIAL
INSTALLATION ACCESSORIES
■ Dryer is plugged into electrical outlet and is
• Vent hood – 4” (10.16cm) opening – 059129
• Aluminum pipe – 4” x 24” (10.16cm x 60.96cm)
– 059130
• Aluminum elbow – 4” (10.16cm) – 059131
• Aluminum window plate – 15” x 20” (38.10cm x
50.80cm) – 4” (10.16cm) hole – 059134
• Flexible aluminum vent duct – 4” (10.16cm)
diameter – 38” (81.28cm) length stretches to
8’ (2.44cm) – 304353
• Clamp for flexible aluminum duct – 304630
• Exhaust duct kit for base or left side exhausting
– 33001881
• Rectangular vent kits – 059144
• Back draft damper 4” – 059146
• NATURAL to LP conversion kit – 308378
• LP to NATURAL conversion kit – 33001287
• Anchor bracket kit – 303740
• Heating element conversion kit, 208 v., not for
Canada – 308590
• Grounding kit 12001875
• Power cords – 240 v, 30 A
4’ – 3-wire – 33001780
5’ – 3-wire – 33001822
6’ – 3-wire – 33001823
10’ – 3-wire – 33001838
4’ – 4-wire – 33001781
6’ – 4-wire – 33001824
6’ – 4-wire – 33001825
properly grounded.
■ Exhaust duct work is hooked up and joints
taped.
■ Plastic flexible duct is NOT used.
■ Use rigid or stiff walled flexible metal vent
material.
■ Dryer is level with all legs firmly on the floor,
with the lock nuts tightened against the base.
■ Gas Models – gas is turned on, there are no
gas leaks.
■ Dryer runs, heats, shuts off.
Page 14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising