Bypassing Zones - True Steel Security

Bypassing Zones - True Steel Security
Bypassing Zones
K E Y P AD C O N T R O L S & I N D I C AT O R S
1
2
GEMINI
SYSTEM ARMED
3
7
ED
ARM
TUS
STA
R
1
2
3
5
B
4
5
6
6
C
7
8
9
4
C O M P U TE R I Z E D S E C U R IT Y S Y S T E M
12
4
U
P
0
G
Q
8
9
10
11
K E Y P AD C O N T R O L S & I N D I C AT O R S
1
Window. Displays system status 5
messages, zone descriptions, etc.
2
STATUS Light. Lights (green) to
indicate that the system is ready 6
for arming.
If a zone is not
secured, the light will be off and
the zone will display in the
window.
7
ARMED Light. Lights (red) to
indicate that the system is armed.
If an alarm has occurred, the
ARMED LED will be flashing.
8
3
4
MENU Button. Selects available
system functions as displayed in
the window.
The selected 9
function is executed by pressing
the U button.
BYPASS Button. (1) Deactivates
selected zones from the system.
(2) reactivates a bypassed zone. 10
RESET Button.
(1) Resets
various system troubles, displays,
etc. (See text).
(2) Resets 11
residential smoke detectors.
Numerical Keys (1-9, 0). Used
to enter codes, zone numbers, 12
etc.
ENTER Button.
Entry key.
Causes the entered code or
selected function to be executed.
STAY Button. (1) Pressed after
a valid User Code, the system will
arm in Stay Mode. (2) If held
down for two seconds and EZ Exit
is enabled, the system will arm in
Stay Mode. (3) If held down for
two seconds and system is armed
STAY, system will arm INSTANT.
AWAY Button. Allows arming
with interior protection on.
STAR Button (G). Is used
with emergency buttons (see
below).
Emergency Buttons. Used with
the G button to signal an
emergency, as follows:
• Press the
7 and the
buttons for Fire Emergency.
G
• Press the
8 and the G
buttons for Auxiliary Emergency.
• Press the
9 and the G
buttons for Police Emergency.
5
A R M I N G AW A Y : S E T T I N G T H E AL A R M W H E N L E AV I N G
SYSTEM READY
INVALID ENTRY
TRY AGAIN
PLEASE EXIT
030 SECONDS
Arming the System
1 Check the keypad for a SYSTEM READY message. The green STATUS light
must be on in order to arm. The window will display “SYSTEM READY”. If the
green light is off and “ZONES FAULTED” is displayed in the window, see below
“Arming with a Faulted Zone”.
2 Arm the system.
! Enter your User Code and press Q.
ZONES FAULTED
! Hold down Q for 2 seconds (with Easy Arming enabled).
The green STATUS light will turn off, the red ARMED light will light and the window
will display “PLEASE
(where “XXX” represents the exit
0 2EXIT”,
B A C K“XXX
D O OSECONDS”
R
time remaining, in 2-second steps). Note: If you enter a wrong code, the keypad
will display “INVALID ENTRY, TRY AGAIN”. Re-enter your code immediately.
3 Leave the
premises. Leave through the exit door before exit time expires.
B Y PA S S ED
BYPASSED
FAULTED ZONES
02 BACK DOOR
CAN’T ARM SYSTEM
...ZONE FAULTED
6
Arming with a Faulted Zone
If the green light is off and “FAULTED ZONES” is displayed in the window, a faulted
zone exists Band
Y PA S Sthe
ED keypad will display the number and zone description of each
0 2problem
B A C K zone
D O Oand
R secure them by closing windows, doors,
faulted zone. Note each
etc. When all zones are secure, the green STATUS light will turn on and the window
will display “SYSTEM READY” or READY TO ARM”.
If you attempt to arm with a faulted zone, a 3-second tone will sound at the keypad.
“CAN’T ARM SYSTEM ...ZONE FAULTED”, will display in the window, indicating that
the faulted zone(s) must either be secured before the panel can be armed or the Zone
must be Selectively Bypassed. See next page, “Selectively Bypassing Zones”.
A R M I N G AW A Y : S E T T I N G T H E AL A R M W H E N L E AV I N G
CAN’T ARM SYSTEM
...ZONE FAULTED
02 BACK DOOR
BYPASS
SYS TBL
SYS TBL
PLEASE EXIT
040 SECONDS
SYSTEM TROUBLE
LOW BATTERY
CAN’T ARM SYSTEM
...PRESS RESET
Selectively Bypassing Zones
If you cannot locate or repair the problem yourself, call for assistance. If you
cannot get immediate help, bypass the problem zone(s) from the system by
pressing B, then the single-digit zone number. The word BYPASS appears on
the display. (You can “un-bypass” the bypassed zone by pressing B and the
zone number again). With the zone(s) bypassed, arm the system (enter your code
and press Q), and leave the premises.
Note: Bypassed zones are unprotected. Therefore, if armed with zones bypassed,
be sure to have the system checked as soon as possible.
System Trouble
If you attempt to arm with a “SYSTEM TROUBLE” display along with an indicated
trouble message (e.g. “LOW BATTERY”; see SYSTEM TROUBLES), the window
will display “CAN'T ARM SYSTEM...PRESS RESET”. If you cannot correct the
problem immediately, press C to arm in this condition. Be sure to call for service
as soon as possible.
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising