0.07.B.0008 SMART NOVA Receiver Insert-23Jul2012-CT

0.07.B.0008 SMART NOVA Receiver Insert-23Jul2012-CT
NOVA and SMART2
single channel receiver
instructions
VERSATILE
MULTI-USER
RECEIVER
The NOVA system incorporates code-hopping
technology to offer the ultimate security in a
remote control.
A unique, randomly changing code is transmitted
with each operation making it impossible to
duplicate the system.
The SMART system uses a unique fixed code
protocol to provide a convenient and efficient
remote control system.
Whether NOVA or SMART, the receiver uses selflearning technology, making it quick and easy to set up.
For the best results, we recommend that the receiver be
mounted as high up as possible, and preferably
away from metal objects and other radio
equipment.
The receiver enclosure is weatherproof, but any holes
drilled during installation should be properly
sealed.
The antenna wire has been tuned to an optimum length,
and should not be modified.
1. Configuring the system
1. Transmitter
Whether NOVA or SMART, each transmitter is uniquely
coded at the factory. It is NOT necessary to open the
transmitter, except when changing the battery. To replace
the battery, rotate the inner casing, and remove from the
outer clip. Using a coin, price apart the inner casing to
expose the battery. Replace with type GP23 or similar.
2. Receiver
Open the receiver housing by inserting a screwdriver into
the slot at the base and twisting (See diagram overleaf).
For pulsed operation:
1. Locate the “learn / JI” pins. With power on, bridge
the two pins with the jumper provided. The red
LED will now illuminate.
2. Press the required button on the transmitter. The red
LED will flash once, indicating that the button has
been learned as a memory button.
If the red LED flashes rapidly, the memory is
full, and the button cannot be memorised.
3. If further buttons are to be memorised, repeat from
step 2. If not, remove the jumper from the “learn / J1”
pins and store on one of the pins. The system is now
ready for use.
For latched operation:
1. Locate the “erase / J2” pins. With power off, bridge
the two pins with the jumper provided. Power up
the unit. The red LED will now illuminate.
2. Press the required button on the transmitter. The red
LED will flash twice, indicating that the button has
been learned as a latched button.
If the red LED flashes rapidly, the memory is
full, and the button cannot be memorised.
3. If further buttons are to be memorized, repeat from
step 2. If not, remove the jumper from the “erase / J2”
pins and store on one of the pins. The system is now
ready for use.
Self-learning memory: The NOVA receiver is
capable of memorising up to 62 buttons; the
SMART, 125 buttons.
Erasing the memory
1. With the power on, the memory may be erased by
bridging the “erase / J2” pins with the jumper
provided. The red LED will begin to flash.
During this time, removing the shunt will
cancel the erase process.
2. After twelve flashes, the red LED will remain
illuminated. Remove the jumper, and the red LED
will flash rapidly as the memory is erased.
3. Store the jumper on one of the pins.
This procedure will remove ALL existing users
from the system memory.
Autolearn mode (for pulsed operation only):
1. The receiver can be set into Autolearn mode by
bridging the “learn / J1” pins prior to applying
power.
Each valid signal received in this mode will both
activate the contact, and be stored in memory. This is
useful when setting up systems with a large number of
transmitters.
The system can be left in Autolearn mode for a period
of time, and will automatically memorise the
transmitters as they are used.
Removing the jumper will cancel Autolearn
mode.
When using Autolearn mode, whether the
receiver is NOVA or SMART, any
corresponding transmitter operated in the
nearby vicinity, may be memorized.
Receiver signal indicator
1. If a signal is received from an unauthorised
transmitter button, the red LED will flash briefly. This
indicates that the transmitter is functioning, but
has not been learned into the system.
NOVA and SMART receiver
technical specifications
Specifications
Operating frequency
Supply voltage
Quiescent current
@12V DC
Maximum current
@ 12V DC
Operating
temperature
Humidity
Sensitivity
Self-learning memory
Receiver enclosure
NOVA
SMART
433.92 MHz
12 - 24V DC
11mA
40mA
-15°C to 50°C
0 - 90% non-condensing
-115dB
62 buttons
125 buttons
UV stabilised ABS
continued overleaf
RECEIVERS
Installation
instructions
Remove cover
1. Insert screwdriver into
slot.
2. Twist screwdriver.
1
2
Figure 1
3. Remove cover.
3
Figure 2
Mount unit
1. Mark position of unit
against mounting
surface.
2. Using a 5mm masonry
bit, drill a hole into
mounting surface.
3. Mount unit using the
fastener supplied.
Rawlplug
O ring
Fastener
Figure 3
Wiring
1. Use a 6mm drill bit to
open the required
cable entry hole.
Cable
entry
holes
6mm
drill bit
Figure 4
5V
2. Route cable into
housing.
3. Terminate cable onto
receiver - refer to
connection diagram
below.
4. Fix cable to wall using
cable saddles.
5. Feed aerial through
one of the spare holes
- stretch out fully for
best results.
6. Seal cable entry
holes with silicone
sealant.
12V
Cable
saddles
Aerial
Figure 5
Connections
1. Supply the unit with 12-24V AC/DC.
2. The output contact is potential-free.
Some applications may require an external
link between NEG and COM.
COM NC
NO
J1=Learn
J2=Erase
M7
NC
NO
12-24V AC/DC
12V-24V AC/DC
NEG
COM
Figure 6
Replace cover
1. Hook the top edge of
the cover onto the top
of the unit.
2. Lower the cover and
press securely into
position.
1
2
Figure 7
FCC information to users
USA and Canada only – where a FCC ID number is
inscribed on the receiver, the following information
is applicable to users:
FCC Label @ FCC 15.21 and 15.105
For Class B – Unintentional radiators:
This equipment has been tested and found to comply with the limits
for Class B digital devices, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications, however, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
&
Reorient or relocate the receiving antenna
&
Increase the separation between the equipment and receiver
&
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
&
Consult the dealer or an experienced radio/TV technician for
help
&
Warning to users @ FCC 15.21 & 15.105
Changes or modifications not expressly approved by
Centurion Systems (Pty) Ltd could void the user's
authority to operate the equipment.
FCC Label @ FCC 15.19
For Class B - Unintentional radiators:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
0.07.B.0008 SMART NOVA Receiver Insert-23Jul2012
www.centsys.com.au
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising