Full D1 Realtime H.264 DVR – 4 CH. Quick Setup

Full D1 Realtime H.264 DVR – 4 CH. Quick Setup
DDR-04
Full D1 Realtime H.264 DVR – 4 CH.
Quick Setup Guide
PACKAGE CONTENTS
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
A.
One (1)
One (1)
Two (2)
One (1)
Two (2)
Four (4)
One (1)
One (1)
One (1)
One (1)
DDR-04 DVR
Remote Controller
AAA Battery for Remote Controller
USB Mouse
4 Screw on Terminal Connector
Hard Drive Screws
12V DC / 2Amp Power Adapter
SATA Cable Inside DVR
Quick Set up Guide Book
User’s Manual & CMS Software CD
B.
C.
x2
D.
E.
F.
x4
x2
G.
H.
Inside the DVR
I.
J.
*Note: Any Return Must Include All Components.
Missing Components will be charge.
We highly recommend installing a UPS Battery Backup System to avoid
power failure restore damage to Hard Drive & motherboard.
Please read this Quick Setup Guide before installation.
MADE IN TAIWAN
R201304-V10
DDR-04 Quick Setup Guide
Panel Definition
1. Front Panel
Item #
Label Name
Function
1
2
3
4
5
6
REC / FOCUS
PLAY / IRIS
REW / SPEED
FF / P.T.Z.
MENU / +
BACKUP / -
7
STOP / ESC
Manual record / focus adjustment(PTZ)
Enter Playback/ iris adjustment (PTZ)
Fast rewind on playback mode / speed adjustment (PTZ)
Fast forward on playback mode / enter PTZ mode
Enter menu page / increase value
Enter backup page / decrease value
Stop playback on playback mode /
Exit menu or jump back to previous page
8
Split / Direction Key
Switch split / Move selected item
9
10
11
Enter
USB
IR Indicator
Validate action
Connect USB thumb drive or mouse
IR Remote receiver
2. Back Panel
Item #
Label Name
Function
1
2
3
4
5
ALARM OUT
Audio in
Video in
Audio out
Video out
6
Spot out
7
8
9
10
11
12
13
14
Power Switch
GND
RS485
ALARM IN
HDMI port
VGA port
LAN
USB port
15
DC12V
1-ch relay output. Connect to external alarm
4 CH Audio input
Video input channels from 1-4
Audio output, connect to the sound box
Connect to monitor
Connect to monitor as an AUX output channel by channel. Video
would be displayed without OSD.
Power on/off
Grounding
Connect to speed dome or keyboard
Connect to external sensor 1-4
Connect to high-definition display device
VGA output, connect to monitor
Network port
To connect external USB devices like USB flash, USB HDD or USB
mouse. Recommend using for USB mouse
POWER INPUT
-2-
R201304-V10
DDR-04 Quick Setup Guide
Control Option
1. Remote Controller
◆ This remote control use AAA battery, the definition as following:
Item #
Button
Function
1
2
3
4
5
6
Record Button
Search Button
Exit Button
Direction button
Enter Button
PIP Button
To record manually
To enter into search mode
To exit the current interface
To move cursor in setup or pan/title PTZ
To confirm the choice or setup
To enter into picture in picture setting mode
To control playback. Play/Pause/Stop/Previous Section/Next
Section/Rewind/Fast Forward
To enter into auto dwell mode
Get information about DVR like firmware version,
HDD information
To enter into menu
To zoom in the images
To choose multi screen display mode
To switch the live image
7
8
SEQ
9
Info Button
10
11
12
13
Menu Button
Zoom Button
Multi Button
Next Button
◆ Switch Remote Control ID
1. Take remote control and point to DVR then continuously press “8”,”8”,”ID(0-65535)”,”Enter”.
2. Make change on DVR ID Setting,
Go to “SYSTEM MENU” > “DEVICE ID” to make change
*The ID must be the same on DVR.
*For example: If ID=1 ,
Please take remote control and point to DVR then press 8,8,1,Enter.
Then go to “SYSTEM MENU” > “DEVICE ID” change the ID=1
2.3 Mouse Control: REQUIRED
◆Connection: Recommend to connect the USB mouse to the back panel.
◆Mouse functions:
1)Under LIVE mode:
On every channel,you could double click the left button to switch FULL SCREEN and double click again to
switch back to original split mode.
On every channel,you could single click right button to popup MENU page.
2)Under MENU page:
Single click left button on any functional icon could enter the
function page and Single click right button to exit function page
or jump back to previous page.
If you want to key in letter or digit, please move mouse to
textbox then single click left button on textbox. The OSD
keyboard will pop up as following,
3)Under Backup mode:
Single click left button to select item, single click right button to jump back to previous page.
4)Under PTZ mode:
Single click left button to operate PTZ function, single click right button to jump back to previous page.
-3-
R201304-V10
DDR-04 Quick Setup Guide
Wizard setup
1. Wizard for language and time setup
Device Name: to set a name of DVR.
Language: to set a proper language.
Date Format: to set a proper display format of time.
Time Format: to set 24 hour or 12 hour format to display.
Time Zone: to set proper time zone (GMT-8: Los
Angeles)
*Caution: Please make sure to set time zone correctly.
To prevent getting different time stamps between local
and remote site.
System Date: to set current system date time.
Please click “next” to next wizard process.
2. Wizard for Record setup
You can setup record frame rate and quality for each
channel and change record resolution.
Adjustable parameter as following,
Resolution: CIF, HD1 or D1
Frame rate: Number of channel.resolution@NTSC frame rate
(PAL frame rate)
4 CH
4CIF@30(25)
4HD1@30(25)
4D1@30(25)
Quality: Highest/ Higher/ Normal/ Low/ Lower/ Lowest
If you want to change all channel setup at once, please
click “All” then setup resolution, frame rate and quality at
right hand side.
Please click “next” to next wizard process.
2.1 Motion Detection Recording:
Motion Detection Recording: Enter Main Menu  Setup  Alarm  Motion
Enable the Channels to turn on Motion Detect Record.
**Motion Schedule Default: is set to Full Time motion recording on all channels.
-4-
R201304-V10
DDR-04 Quick Setup Guide
If Schedule Motion Recording needs to be changed:
To modify motion recording schedule click on the pencil icon located on the upper right of the screen, then
click on desired days and times to schedule recording when motion trigger.
If same schedule apply to all channels. After highlighting desired squares apply settings to “All” Channel, click
“Copy”and click Apply to save setting. To Enable full time motion Recording, highlight the entire Blue Grid.
2.2 Full Time Recording :
1. Press “Record” Button on the front panel of the DVR. Green box will appear on screen to confirm that
manual recording is enabled. Press “Record” Button again to stop recording.
OR Right click on main screen and select “Record”.
Note: Definition of Holding Time (on motion detect setting) :
After motion record is activated and there is NO activity within 10 seconds this will be handled as one event.
Otherwise if there IS activity within that time frame it will continue recording.
Note: Change Daylight Savings on the first week of March and second week of November.
3. Wizard for HDD setup
You can format HDD by using “Format” function.
After HDD format completed, it will show
“Normal” label on status.
*Please make sure to backup all HDD data
before you format the HDD.
All HDD data will be erased after HDD formatted.
Please click “Finish” to get into login page.
-5-
R201304-V10
DDR-04 Quick Setup Guide
Network Setup: Static IP Address & DDNS
Part 1. Static IP Address
1. Enter Main Menu screen by pressing the MENU
button on the front panel of the DVR.
Then enter password “123456” and click Login
2. Select Setup.
3. Select Network.
4.
Select “Obtain an IP address automatically,”
turn on this feature.
Then Select Apply at the bottom of the screen to
restart the network.
This will generate a new IP Address.
(Make sure Ethernet Cable is plugged in)
5. After Apply, the IP Address, Netmask, Gateway, and DNS addresses should automatically be generated.
*For STA
TIP: Write down HTTP Port, Server Port, and IP Address on a piece of paper for reference. You will need
these numbers later in the installation.
TIP: If you do not know a DNS address and the DVR did not populating those fields by itself, try 8.8.8.8 and
8.8.4.4. These are Google's public DNS addresses, and in addition to working well.
6. Uncheck “Obtain an IP address automatically” to turn off this feature and make IP Address stay the same.
Then click Apply.
Continued For DDNS
Set up
Part 2
-6-
R201304-V10
DDR-04 Quick Setup Guide
Part 2. DDNS
1. Continue Part 1: Select “Other Setting” from the Tab bar and turn on DDNS.
2. Select DDNS Type and pick one website from the given field to register your Host Domain Name.
TIP: We recommend using www.dvrdydns.com, www.dynddns.us, and www.no-ip.com because they are free.
3. Using your Internet Browser, go to that website you selected and REGISTER to obtain User Name,
Password, and Host Domain information to setup DDNS for your DVR.
TIP: Write down Name, Password, and Host Domain information for reference to use later in installation.
Step 1
Step 2
Step 3
Tip: When using other DDNS websites you may be
required to enter your external IP Address to
register your Host Domain Name.
- To find your external IP Address use this website:
http://www.whatsmyip.net
-7-
R201304-V10
DDR-04 Quick Setup Guide
4. Now enter User Name, Password, and Host Domain that you wrote down earlier and click Test - After Test passes,
then click Apply and Exit.
TIP: The DDNS URL will always be in the form of
<hostname>.dvrdydns.com
If you are unable to access the DVR from the
internet using the DDNS URL, but the IP works,
please double check that you have the DDNS URL
correctly typed
5. Finally, you will need to set port forwarding on your internet-facing router/gateway to direct port 80 traffic to the DVR.
Also you will need to port forwarded your server port 6036 to stream video and audio as well. Locate the page in your
router settings to set port forwarding (may also be labeled “firewall”).
HTTP Port: Port for IE connection. (Default is 80)
Server Port: Port for video and audio streaming. (Default is 6036)
Incoming Port Range (advance)
Forward Port (advance)
IP
Protocol (advanced)
80
6036
80-80 (or alternative if port 80 is being used)
80, 6036
Your DVR’s internal IP, typically 192.168.x.x
TCP & UDP
TIP: Some consumer router/gateway devices may present the firewall settings as a list of services to forward. In this case,
consult the manual for settings for creating a custom service and use the above values. For router/gateway devices provided
by your ISP, please contact your ISP technical support.
DDNS Hosting Server
Item #
DDNS Server Website
Notes
1
www.dvrdydns.com
Recommended, Free
Log In or Create a FREE account to start monitoring this domain name.
2
www.no-ip.com
Recommended, Free for entry level service. Enhanced Domain membership for more features is
available but is charged. Visit website for more information.
3
www.dyndns.us
Recommended, Free
Log In or Create a FREE account to start monitoring this domain name.
4
www.meibu.com
It’s a Chinese website, Free for second- level domain names, but the website will verify your
information.
5
www.dyndns.com
$15/year.
* Note: For further assistance regarding technical support and more details, please visit DDNS Server Website.
Mobile App: Super Live Pro
*Please check specification sheet on the User’s Manual.
**Quick Setup Guide & User’s Manual are subject to change without notice.
-8-
R201304-V10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising