BlinkFX DMX 14 Channel Emitter Controls DMX QUICK START SET

BlinkFX DMX 14 Channel Emitter Controls DMX QUICK START SET
BlinkFX DMX 14 Channel Emitter Controls
CH 1 Dimmer
255 0
Dark Bright CH 2 Red
1) For DMX operadon of BlinkFX control emieer(s), set dip switch pin 10 to "On" then set fixture address start channel using pins 1-­‐9 (see DMX dip switch addressing key at boeom of page). The following example is set for DMX control with a fixture address of "1". Muldple emieers may be synchronized under one common address or zoned with different addresses. CH 3 Green
CH 4 Blue
193 -­‐ 208 = ID 13 CH 5 Color Wheel
0 = Honor RGB of CH 2, 3 & 4 CH 6 Color Wheel Speed
Change Speed When CH 5 = 147-­‐255 CH 7 Blink On Time
0 CH 8 Blink Off Time
0 CH 9 Pulse On Time
DMX QUICK START SET-­‐UP AND OPERATION 1-­‐16 17-­‐31 32-­‐47 241 -­‐ 255 = ID 16 147-­‐255 Cycle All 209 -­‐ 224 = ID 14 48-­‐63 64-­‐79 80-­‐95 96-­‐112 113-­‐129 130-­‐146 255 1 Fast Slow 255 Fast Slow 255 Fast Slow 255 0 Fast CH 10 Pulse Off Time
0 CH 11 Buzz On Time*
0 CH 12 Buzz Off Time*
0 Slow 255 2) Plug the BlinkFX control emieer into a 110v AC power plug. Then connect the emieer to an industry standard DMX512 lighSng control board with at least 14 Channels using 3-­‐pin XLR cable. Follow the instrucdons included with your DMX512 control board to set up a fixture profile for the 14 Channel BlinkFX emieer. 3) IMPORTANT! When connected to a DMX control board, set Channel 14 Emieer Power to a value greater than "0" before aeempdng to set other DMX channel values. Experiment with emieer power seings to maximize response rate for the area of use. Small areas require lower power seings. Too much power in a small area creates signal clueer reducing the responsiveness of the LED light devices. Larger areas require higher power seings for greater range and responsiveness. Test your venue thoroughly before the event to dial in the ideal power seings. Range and coverage results will vary depending on the venue. 4) Ideal placement of emieers is mounted on a truss or tower at least 10 feet above the audience at a downward angle. Smaller venues may work with lower placement, above head high. When using muldple fixtures to cover a large area or achieve zoned effects, experiment ahead of dme with placement and emieer power seings (adjust Channel 14 Emieer Power for test). Walk around the venue with BlinkFX receiver device to test for range and dead spots. Adjust emieer placement and power accordingly. Fast Slow 255 SPECIAL EFFECTS SETTINGS Strobe -­‐ White Channel 1 > 0; Channel 5 > 146; Channel 6 = 0 to 3 Fast Slow 225 -­‐ 240 = ID Strobe -­‐ Color Wheel Channel 1 > 0; Channel 5 > 146; Channel 6 = 4 to 15 255 Fast Slow 16 -­‐ 30 = ID 1 CH 13 Device ID
CH 14 Emitter Power
Strobe -­‐ Specific Color Channel 1 > 0; Channel 5 > 146; Channel 6 = 0 to 3 0 -­‐ 15 = Global All IDs Respond 31 -­‐ 45 = ID 2 46 -­‐ 60 = ID 3 61 -­‐ 75 = ID 4 91 -­‐ 105 = ID 6 106 -­‐ 120 = ID 7 121 -­‐ 135 = ID 8 136 -­‐ 150 = ID 9 151 -­‐ 165 = ID 10 166 -­‐ 180 = ID 11 181 -­‐ 195 = ID 12 196 -­‐ 210 = ID 13 211 -­‐ 225 = ID 14 226 -­‐ 240 = ID 15 241 -­‐ 255 = ID 16 76 -­‐ 90 = ID 5 Off STAND ALONE OFFLINE MODE (NO DMX REQUIRED) 255 0
Twinkle -­‐ Asynchronous Blink Channel 1 > 0; Choose Any Color; Channel 7 = 0; Channel 8 = 255 First, set dip switch pin 10 to off. Emieer will not require DMX input commands and no DMX controls or XLR cable are necessary. Only AC power is required to operate emieer in stand alone beacon mode. See "Stand Alone Mode Dip Switch Seings" chart at lower right for control seing opdons. Full Power 225 -­‐ 240 = ID 15 241 -­‐ 255 = ID 16 209 e-­‐quipped 224 = ID 14 with *Functional only on Wink devices optional buzzer.
STAND ALONE OFFLINE MODE DIP SWITCH SETTINGS (No DMX Required)
Pin
10
1
2
3
4
5
6
7
8
9
Function
OFF = Stand Alone Mode ON = DMX Mode (use Pins 1-­‐9 to address)
Pins 1-­‐3 determine power (Off-­‐Off-­‐Off = 100%, On-­‐Off-­‐Off = 80%, Off-­‐On-­‐Off = 40%, Off-­‐Off-­‐On = 20%, On-­‐Off-­‐On = 10%)
Blink at rate 500ms on / 500ms off
Pulse at rate 250ms on / 250ms off; Both Pin 4 & 5 on changes to 500ms on/off
TBD Future Function
Red
Green
Blue
Version v0.07, 1-­‐31-­‐14
DMX 512 MODE DIP SWITCH ADDRESSING CHART
Pin
10
1
2
3
4
5
6
7
8
9
Values
On
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
Function
Standard DMX Mode
DMX starting address bit 1 (Least Significant Bit)
DMX starting address bit 2
DMX starting address bit 3
DMX starting address bit 4
DMX starting address bit 5
DMX starting address bit 6
DMX starting address bit 7
DMX starting address bit 8
DMX starting address bit 9 (Most Significant Bit)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising