Product Instructions VERDE LEDDownlights, PEREGRINE

Product Instructions VERDE LEDDownlights, PEREGRINE
Product Instructions
VERDE LED Downlights, PEREGRINE
USER GUIDE:
The purpose of this user guide is to explain the necessary steps for the proper use of a LED Downlight and
to assure peak performance of this product. It is intended for use as reference by a fully qualified
electrician or technician. This document should never be considered a substitute for any provision of a
regulation or state and/or local code. Please read this entire manual to fully understand and safely use this
product. Specifications are subjected to change without notice. Please visit www.verdeled.com for the
most recent technical data.
GETTING STARTED This guide contains important information about installing and operating your new LED
Downlight safely and accurately.
Product description:
MODEL
VER-2D90-X-YYY
VER-2D165-X-YYY
VER-2D205-X-YYY
Dimension of cut-outs
Ø90-100mm
Ø165-185mm
Ø205-230mm
Exterior dimensions
Ø110x55mm
Ø195x54mm
Ø245x54mm
Declaration of the product:
Each package box includes LED Downlight 1pc, LED driver 1pc.
CAUTION:
1. Risk of fire or electric shock. Ensure that the power supply is off when installation is carried out.
2. Before installation the fully qualified installer must determine whether the power supply is in
the electrical input range stated in the Product Parameters table (see below) of the luminaire.
3. Do not remove the LED Downlight or LED driver cover.
4. Any constructive change of the luminaire or driver is not permitted.
5. Lamp suitable for 50Hz or 60Hz operation.
6. The device should be installed and operated by a qualified electrician or technician in accordance
with relevant local codes.
7. Do not use sharp tools near or on the surface of the device.
8. Lamp is suitable for dimming when operated with a dimmable driver.
9. Lamp is suitable for emergency operation when operated with an external emergency pack.
10. Ingress grade IP20, Driver IP20. Lamp to be used in dry conditions.
11. Do not install the downlight in touch with insulating material under any circumstances.
12. All VERDE products comply with surge immunity as specified by EN 61547:2009. However, the
Verde Warranty also requires additional surge protective devices to be installed on-site against
the effects caused by remote lightning strikes, inductive or capacitive coupling, and switching
surge voltages. These are typically installed at the main distribution and sub-distribution panels
and are to be maintained and operational always. Refer to industry experts such as
www.phoenixcontact.com for further surge protection advice
Unpacking:
1. Unpack and carefully examine the product.
2. Report any damage and save all packing materials if any part of the product was damaged during
transportation.
3. Do not attempt to use the apparatus if it is damaged.
Page 1 of 2
May 2017
User Responsibilities:
The responsibility to comply with all national and local laws, ordinances, and regulations in regards to the
installation, maintenance and operation of the device lies with the buyer and handler of the device. These
parties may include, but are not limited to the contractor, installer, purchaser, owner, and user of the
product. Consult Lighting Application Engineering services as needed.
Product parameters:
Model number
VER-2D90-6-840
VER-2D165-12-840
VER-2D205-20-840
Input Voltage
Power
Optics
Working
Temperature (°C)
AC220-240V 50/60Hz
AC220-240V 50/60Hz
AC220-240V 50/60Hz
6W
12W
20W
Frosted
Frosted
Frosted
-20°C to 40°C
-20°C to 40°C
-20°C to 40°C
INSTALLATION INSTRUCTIONS:
1. Ensure the mains are disconnected before handling the luminaire.
2. In case of a new installation: Make a cut-out of diameter between the limits stated in the Product
Description Table (see above).
3. In case of replacing an existing downlight: Remove from the ceiling the existing downlight
according to the manufacturer’s instructions and disconnect it from the mains. Make sure the
existing cut-out has a diameter between the limits stated in the Product Description Table (see
above).
4. Wire the LED driver and downlight as the following diagram:
5. For dimmable installation you will need a 1-10V dimmer switch (not provided with the product). In
this case please follow the wiring instructions of your dimmer switch & take note of the input
voltages.
6. Push both clips up and carefully insert the downlight into the ceiling.
7. Turn on power supply.
Page 2 of 2
May 2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising