XtraLam 110H roll laminator

XtraLam 110H roll laminator
XtraLam 110H roll laminator
XtraLam laminators are the ideal starter device for digital printers and repro houses and photo shops that are wanting to in-source their lamination process adding value to your business proposition.
XtraLam 110H roll laminator
Features
• All the laminators feature high spec silicone rollers which are far better than natural rubber
rollers found on cheaper machines. The advantage of the silicone rubber rollers is that they
are more conforming to the thickness of the digital print (yes digital printer toner and ink has a
definite thickness that makes the surface of the sheet irregular) and better presses the laminate
to the substrate. This is because the silicone rubber gives a little to take up the irregular surface
and gives a more equal pressure to the film, reducing the incidence of bubbles under the film*
• The machines all are robustly built with heavy roller steel cores, heavy side frames and heavy
duty drive motors and electrics
• Quick warm up time
• The laminate rolls are easily mounted to the roller shafts which can adapt to several core sizes
• The finished products is outfed by the secondary feed rollers
• The film web tension is controlled by the tension rollers
• The mandrel turning resistance (tension on the film) can be adjusted
• The roller spacing can be adjusted by knob to many positions for different thickness of substrate
to 0.6 mm, the top roller is held down by spring pressure on to the laminate
• The control panel is easy to understand and allows you to adjust temperature, feed speed,
forward or back motion, according to the substrate and film requirements. The last settings are
memorized for your convenience
• The infeed of the film web is easy and straightforward
• The infeed area is guarded
• There is a adjustable left side guide on the infeed table to align the substrate to be fed into the
rolls
• A reverse function is also included
• A optional corner rounder with 2 diameter punch tools is available to finish the process
Specifications subject to change without notice, errors and omissions excepted. - Preliminary Specifications.
Tasco Gent
Tasco Lille
Tasco Paris
Industrial Park Asper - Legen Heirweg 59
130, Boulevard de la Liberté
13, Rue Marie Poussepin - Z.A. Lavoisier
9890 Gavere BE
F-59000 LILLE
F-91410 DOURDAN
Tel. +32 9 281 08 50
Tel. +33 3 62 26 00 22
Tel. +33 3 62 26 00 20
Fax +32 9 281 08 70
E-mail info@tascofrance.fr
Fax +33 3 62 26 00 23
E-mail info@tasco.be
RCS LILLE METROPOLE B 793 237 843 - Capital : 25.000 €
Site www.tasco.be - www.tascofrance.fr - Webshop www.inkjetlabel.com - Webshop papier www.tapaper.eu
Features
XtraLam 110H roll laminator
Width: 110cm
Control panel: Digital
Optimal film thickness: 30 to 150 micron
Slitter for trimming the film on the outfeed
Newly designed easy to fit roller carrier shafts with multiple mandrel diameters.
Silicone rubber rollers with long life and high temperature resistance (all three)
Substrate: to 1mm**
Warm up time: ca. 10 min.
Min./max. temp.: 40 to 150 °C or room temp (cold function)
Variable roller setting using an index lever
Variable feed speed in 9 steps from 0.35 to 3 m/min.
Lower roller off switch for single side lamination*
Reverse button
• Note, sheets with fuser oil should be left to dry for 4 to 6 hours before lamination, to avoid
bubbling, special film with heavy glue application may be needed for best results when used
with xerographic production
• Trimming of the film overhang may reduce adherence
* When doing single side lamination the substrate should be as wide as the fold to avoid the glue going on to
the opposite roller.
** Can be even more, up to 3mm, but film wrap will be less tight.
Specifications subject to change without notice, errors and omissions excepted. - Preliminary Specifications.
Tasco Gent
Tasco Lille
Tasco Paris
Industrial Park Asper - Legen Heirweg 59
130, Boulevard de la Liberté
13, Rue Marie Poussepin - Z.A. Lavoisier
9890 Gavere BE
F-59000 LILLE
F-91410 DOURDAN
Tel. +32 9 281 08 50
Tel. +33 3 62 26 00 22
Tel. +33 3 62 26 00 20
Fax +32 9 281 08 70
E-mail info@tascofrance.fr
Fax +33 3 62 26 00 23
E-mail info@tasco.be
RCS LILLE METROPOLE B 793 237 843 - Capital : 25.000 €
Site www.tasco.be - www.tascofrance.fr - Webshop www.inkjetlabel.com - Webshop papier www.tapaper.eu
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising