HBD7S - Honeywell Video
HBD7S(X) Bullet Camera Quick Installation Guide
Introduction
Dimensions
8.54″ (217 mm)
Thank you for purchasing a Honeywell HBD7S(X) bullet camera. Follow the instructions in this guide to
install your camera. To configure the camera settings, refer to the HBD7S(X) Bullet Camera Configuration
Guide.
3.27″ (83 mm)
4.84″ (123 mm)
Important Safety Instructions
3.68″ (93.5 mm)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
WARNING
Installation and servicing should be performed only
by qualified and experienced technicians to conform to all local
codes and to maintain your warranty.
WARNING
This device is configured for 12 V DC or 24 V AC
operation. Do not connect to a higher voltage. Use only with NTRLapproved Class 2 power supplies.
1 Installing the Camera
Before You Begin
Before you begin installing the camera, check that you have received all of the parts listed below.
If any parts are missing or damaged, contact your dealer immediately.
•
•
•
•
•
Camera (cable included)
Manuals
Video test cable
DC power pigtail
Mounting plate
•
•
•
•
Focus and zoom adjustment tool
4 socket head cap screws
4 pan head screws
1 hex key
Connecting the Camera Cable
•
Read and keep these instructions.
•
Please ensure that your installation area can safely support the weight of the camera.
•
Do not aim the camera toward an extreme light source to prevent damage to the CCD.
•
Do not touch the camera lens or bezel (front glass plate).
•
Do not drop the camera or subject it to physical shock.
•
Do not use a strong or abrasive detergent when cleaning the camera.
•
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of 14°F to 122°F [–10°C to 50°C]).
Document 800-15430 – Rev A – 07/2013
BNC Video Out (Yellow)
DC Power Jack (Red)
1.
Connect the camera’s video output to the video input on your monitor or DVR.
2.
Connect the camera’s power input to a 12 V DC or 24 V AC power supply.
HBD7S(X) Bullet Camera Quick Installation Guide
3 Configuring the Camera
Mounting the Camera
1.
Using a Phillips driver (not supplied), attach the mounting plate to the mounting surface (with the
foam side facing the wall) using the four supplied 1-inch (25.4 mm) pan head screws,
2.
Using the supplied hex key, attach the camera and bracket to the mounting plate using the four
supplied 3/8-inch (9.52 mm) socket head cap screws. Ensure that the notch in the bracket base is
facing down.
The camera is programed using on-screen display (OSD) menus.
LENS
EXPOSURE
WHITE BALANCE
DC
MANUAL
SHUTTER
AGC
SENSE-UP
BLC
D-WDR
RETURN
ATW
AWB
AWC->SET
MANUAL
DAY&NIGHT
3DNR
SPECIAL
COLOR
B/W
AUTO
EXT
OFF
ON
CAM TITLE
D-EFFECT
MOTION
PRIVACY
DEFECT
DEFOG
RETURN
ADJUST
RESET
EXIT
SHARPNESS
MONITOR
FACTORY
RETURN
Positioning the Camera
After the camera is mounted, adjust the multidirectional bracket to set the camera’s field of view.
There are three adjustment points.
180°
360°
Adjustment
screw
360°
Adjustment
screw
Adjustment
ring
These menus are controlled by the built-in OSD joystick on the underside of the camera
(next to the focus and zoom controls).
1.
Loosen the adjustment screws with the supplied hex key, move the camera to the desired position,
and then tighten the screws.
2.
Loosen the adjustment ring, move the camera to the desired position, and then tighten the ring.
2 Setting the Focus and Zoom
•
Press down and hold the OSD joystick for two seconds to
bring up the OSD main menu on the connected monitor.
•
Push the joystick up or down to move up or down through
the list of menu options.
•
Press down on the joystick to to enter a submenu ( ) or
to execute (set) a menu selection.
•
Push the joystick left or right to change a menu setting.
SET UP
The focus and zoom controls are located on the underside of the camera.
1.
2.
3.
4.
Unscrew the cap on the underside of the camera to access the
focus and zoom controls.
ZOOM
Connect the supplied video test cable to VIDEO TEST and
connect the other end to a portable service monitor.
Adjust the camera’s focus and zoom settings using the supplied
tool. If the focus and zoom adjustment screws do not move
freely, loosen the lock screw.
Tighten the lock screw to prevent the focus and zoom settings
from changing as a result of camera vibration.
FOCUS
LOCK
VIDEO TEST
SET UP
www.honeywell.com/security
+1 800 323 4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-15430 – Rev A – 07/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising