020-0893-80101 RPL1000 Manual RevB ENG.ai

020-0893-80101 RPL1000 Manual RevB ENG.ai
RevA 02-2017
USER MANUAL - RPL1000V2 RACKLIGHT | POWER CONDITIONER | USB CHARGER
Welcome
Thank you for choosing Hill Audio for your sound system. To make sure that this product meets your
expectations and provides long-term, reliable performance, please read and follow this instruction
manual carefully.
Manual Language
UK
FR
DE
ES
PT
IT
This user manual is written in English. For other languages, visit
Ce guide est écrit en anglais. Pour les autres langues, visitez:
Diese Anleitung ist in Englisch verfasst. Für andere Sprachen:
Este manual está escrito en Inglés. Para otros idiomas, visite:
Este manual está escrito em Inglês. Para outros idiomas, visite:
Questo manuale è scritto in inglese. Per altre lingue, visitare:
www.hill-audio.com
www.hill-audio.com
www.hill-audio.com
www.hill-audio.com
www.hill-audio.com
www.hill-audio.com
Important safety instructions
Read these instructions and all markings on the product. Keep these instructions.
Heed all warnings and instructions, both in this manual and on the product.
Clean only with a dry cloth. Unplug from AC supply before cleaning.
Do not use this product near water and avoid any exposure to water.
Before connecting this product to any AC supply, make sure to check whether the AC mains voltage and frequency match the indication on the product and its packaging.
Only connect this product to an AC supply with sufficient power handling, protective earth connection, ground-fault (earth-fault) protection and overload protection.
Disconnect the product from the AC supply during thunderstorms or longer periods of being
unused.
Make sure any heat sink or other cooling surface, or any air convection slot , is exposed sufficiently
to free air circulation and is not blocked.
Do not operate this product in environmental temperatures exceeding 35 degrees Celsius and/or
85% relative humidity.
Position the product in a safe and stable place for operation, out of reach of unauthorized persons.
Make sure any cable connections to and from the product are neither subject to potentially destructive mechanical impact nor present any risk of stumbling or other accident risk to people.
Audio equipment may generate sound pressure levels sufficient to cause permanent hearing
damage to persons. Always start up at low volume settings and avoid prolonged exposure to sound
pressure levels exceeding 90 dB.
Do not open this product for service purposes. There are no user-serviceable parts inside.
Warranty will be void in any case of unauthorized service by the user or other not authorized persons.
Take any precaution required by local law, applicable regulations or good business practice to avoid
injury of people or material damage by use of this product.
Explanation of symbols used in this manual and on the product:
ATTENTION!
Read manual
before installation
and operation.
PAGE 1
DANGER!
Safety hazard.
Risk of injury or death.
WARNING!
Hazardous voltage.
Risk of severe or fatal
electric shock.
WARNING!
Fire hazard.
USER MANUAL - RPL1000V2 RACKLIGHT | POWER CONDITIONER | USB CHARGER
Description
The RPL-1000V2 is a unique combination of a dimmable rack light, a power conditioner, a power
distributor, an AC line volt meter and a USB 2A charger for mobile devices - all in a neat and compact
1U rackmount case. The power conditiong function protects all connected equipment from surges
and spikes, and the built-in circuit breaker provides overload protection. This unit makes the perfect
centre piece for professional equipment racks in all kinds of applications, whether mobile or installed.
Health advice
This unit produces and absorbs electromagnetic radiation. The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC requirements. A corresponding sign is printed
on the backside of the unit. Any change or modification may affect the behavior of the unit concerning
electromagnetic radiation, with the CE requirements eventually not to be met any more. The manufacturer takes no responsibility in this case.
Functional advice
This unit is immune to the presence of electromagnetic disturbances – both conducted and radiated
- up to a certain level. Under peak conditions, the unit is classified to show a “class C” performance
criteria and may encounter temporary degradation or loss of function which may need manual help
to recover. In such case, disconnect the AC power from the unit and reconnect it again to recover.
Environmental advice
This unit is built to conform to the ROHS standards and the WEEE directive 2002/96/EC of the
European Parliament and of the Council of the European Union. Under these regulations, the product
shall not be discarded into regular garbage at the end of its life, but shall be returned to authorized
recycling stations.
Unpacking
Please check that the box contains the following items:
Main parts:
1 pc. RPL-1000V2 main unit
1 pc. IEC C-19 plug for self-assembly
5 pcs. IEC C-14 plug for self-assembly
1 pc. Operation manual
If any part is missing, please contact your dealer immediately for replacement.
NOTE: this unit does not contain ready-for use supply or output cable assemblies.
Warning
After unpacking, and before plugging the AC cord in the wall outlet, check whether the
AC mains voltage and frequency is the same as this product is specified for (see rear
panel of product, close to the AC cord inlet). Whenever the specified voltage or your AC
plug should not match the local conditions, do NOT plug the AC cord into the wall outlet,
and contact your dealer immediately.
This device is specified for a total of 15A of load. Exceeding this maximum load can
damage internal components and may yield a risk of malfunction, shock hazard or fire. It
is not recommended to connect devices such as incandescend lamps, fog machines or
high-power audio amplifiers to this unit.
To provide protection on a system-level, this device must be connected to an earthed AC
supply. Usage with unearthed AC supply is strictly prohibited. In mobile systems, the
operator must check whether the earth contact of the AC supply line is connected to
earth accordingly.
PAGE 2
USER MANUAL - RPL1000V2 RACKLIGHT | POWER CONDITIONER | USB CHARGER
Controls and Connections
1
Controls - Front
3
6
Connections Rear
8
PAGE 3
5
4
7
2
USER MANUAL - RPL1000V2 RACKLIGHT | POWER CONDITIONER | USB CHARGER
Functional Description
The RPL-1000V2 is a dimmable LED rack light, a power conditioner, a power distributor, an AC line
volt meter and a USB 2A charger in one unit. The power conditiong function protects all connected
equipment from surges and spikes, and a built-in circuit breaker provides overload protection.
1
Power switch. This switch switches the complete unit on and off, including the USB charger
section (6), the racklight (3 & 4) and the rear-side power outlets (7). Note that in case the fuse
breaker (2) was tripped, the unit will be off even if the power switch is on.
2
Fuse breaker. This is a 15A fuse breaker in series with the power switch, which will trip if the
total power drawn through the power cord (8) exceeds 15A. If the breaker was tripped, switch
the unit off via the on/off switch (1), reduce the connected load, press the actuator on the
breaker and power the unit up again via the power switch (1).
3
LED light. This is a downwards-directed LED strip with daylight colour temperature. Provided
this unit is mounted in the top position of a rack, it can illuminate the user surfaces of devices
mounted below. The LED light can be switched on and off and adjusted in its brighntess via the
dimmer control (4).
4
LED light on/off switch and brightness control. Turn this fully counterclockwise to reduce the
brightness and turn it over the detent at the fully counterclockwise position to switch the LED
light (3) off. Accordingly, turning it clockwise switches on and increases the brightness of the
LED light (3).
5
AC Volt Meter. This display indicates the current voltage of the AC supply to which the power
cord (8) is connected, in full volts, with about 1% accuracy. This is helpful to determine
whether malfunction of equipment may be related to AC supply issues.
6
USB charging port. This is a USB type A socket, where the USB power lines carry 5V DC and
deliver up to 2A of current. This is sufficient to also charge devices with larger current requirements such as tablet computers.
ATTENTION:
This port provides 5V DC regulated voltage. No current regulation is provided however, so this port is only suitable for charging devices with on-board charge
current management. The manufacturer of this product does not accept any liability for charging compatibility and subsequent potential damages.
7
Switched AC Outlets. These are ten IEC 60320 - C13 outlets, which are switched on and off
simultaneously via the power switch (1). Each single outlet is limited to 5A load, each group of
5 outlets limited to 8A, while the total load of all ten outlets together may not exceed 15A. If
the load exceeds 15A, the circuit brealker (2) will trip. It is thus not recommended to connect
devices such as incandescend lamps, fog machines or high-power audio amplifiers to these
outlets. The voltage available at these outlets is filtered for spikes, surges and RF.
ATTENTION:
This product is not a power sequencer, so all outlets will be switched on and off at
the same time. If power sequencing is needed to reduce the surge current during
powering up, this product is not suitable.
8
AC inlet. This is an IEC-C20 power inlet capabale of handling up to 20A current. Make sure to
only connect AC cords to this inlet which can carry the required power (250V/16A). It is
essential that the outlet to which the power plug is connected is properly earthed, as otherwise no earthing will be provided to any devices connected to the AC outlets (7), which may
result in unexpected performance for equipment which requires proper earthing, or in safety
risks.
PAGE 4
USER MANUAL - RPL1000V2 RACKLIGHT | POWER CONDITIONER | USB CHARGER
Technical Specifications
AC IN............................................................................................................................................................AC 110-250V 50Hz
Switched Outlets...................................................................................................................................10 (2 groups 5 each)
Max. Output Current (per outlet/group)...................................................................................................15A (5A/8A)
Maximum suppressible spike volage.....................................................................................................................340V AC
Maximum energy absoprtion of spikes............................................................................................................240 Joules
Noise Attenuation...........transverse & common modes: 20dB @ 200kHz, rising to >40dB, 1-100 MHz
Circuit Breaker..........................................................................................................................................................................15A
Power consumption (internal electronics, without external loads).....................................................max. 25W
Dimensions.................................................................................................................................W483xH44.5xD150.0mm
Weight....................................................................................................................................................................................1.95 kg
Maintenance and warranty
While we have chosen the best components to make this product as rugged and reliable as possible, some parts in audio
products (potentiometers, faders, switches) are subject to wear which is a matter of operation cycles, and not of time.
While providing a full time-based warranty according to the country’s of purchase requirements on the function of the
electronic circuitry, we hence have to limit the warranty on such electro-mechanical parts to 90 days from the date of
purchase.
In many cases, malfunction of electro-mechanical parts occurs due to dust contamination, which may require cleaning of
such parts. As the inside of such parts is not accessible, a common practice is to use cleaning fluids in the shape of
sprays. Please be reminded that many of such fluids contain chemicals which may wash away the dust but at the same
time corrode or damage contact surface and may cause cosmetic damage to other parts. We hence explicitly exclude
any claims for exchange of damaged part due to mechanical or chemical impact.
PAGE 5
USER MANUAL - RPL1000V2 RACKLIGHT | POWER CONDITIONER | USB CHARGER
PAGE 6
EC Declaration of Conformity
Manufacturer:
Address:
Adelto Technologies Limited
Unit 2A Springfield Road, Springfield Industrial Estate
Burnham-on-Crouch, Essex CM08UA, England
We declare on our own responsibility, that the equipment
Hill Audio RPL-1000V2
is in conformity with the following directives and standards or regulations:
EMC Directive 2004/108/EC
EN55103-1:2009 (Emissions)
EN55103-2:2009 (Immunity)
EN61000-3-2:2006 + A1:2009 + A2:2009
EN61000-3-3:2008
LVD Directive 2006/95/EC
EN60065:2002 A1:2006 + A11:2008 + A2:2010
ROHS Directive 2002/95/EC
and is marked as follows:
Burnham-on-Crouch, 3. February 2017
Place and date of issuing
Authorized Signature
www.hill-audio.com
Hill Audio products are developed, manufactured and distributed by
Adelto Technologies
Unit 2A Springfield Road, Springfield Industrial Estate, Burnham-on-Crouch, Essex CM08UA, England
www.adelto.com | sales@adelto.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising