Control Valves
Control Valves
Control Valves
Fully assembled sectional body hydraulic directional control valves fromParker FPS with bolt kits and end plates for
mobile and industrial hydraulic system, open center hydraulic systems only.. Properly torqued with pressure preadjusted to 2000 psi. Relief valve can be re-adjusted for settings of 700 psi to 2000 psi. Max flow is 12 gpm and
180 deg F. SAE 6 ports. Each spool includes handle. Can be used with Joy Stick and Power Beyond options
purchased separately.
FPS MV3-2000 2 way, 3-position, 1 Spool,
Spring Centered, Fine Metering
ConVal 1
$426.00
Parker MV3
2 way, 3-position, 2 Spool,
Spring Centered
(Picture shows this control valve with
a power beyond option included)
ConVal 2
$476.00
FPS MV3 -2000 2 way, 3-position, 4 Spool,
Spring Centered with SAE 6 ports.
Con Val 4
$576.00
Power Beyond Option
The power beyond option is pre-assembled in a
control valve, and cannot be purchased
separately.. Port Plug included.
Ask for this option when you plan to use two
attachments on your tractor at the same time,
such as a Loader and a Backhoe.
Power Beyond
$50.00
Converts a 2 section FPS MV3 control valve to
a single handle control. Available with straight
or bent handle.
Joy-Straight
$75.00
Converts a 4 section FPS MV3 control valve to
a two handle control. Available with bent
handles.
Joy-Bent
$150.00
Flow Dividers
Flow Dividers
Designed to synchronize the operation of multiple cylinders, hydraulic motors, or other hydraulic circuits to provide
proportional division of a single pump output to two circuits, or to combine flows from two sources to provide a single
greater flow to a hydraulic cylinder or motor.
B-50 Flow Divider
Proportionally divides a single flow of
hydraulic oil. Maybe combined in reverse
direction and synchronized in both
directions.
Flow Divider
$135.00
Rotory Flow Divider
Synchronizes the operation of multiple
cylinders or hydraulic motors to provide
proportional division for a single pump
output to several circuits. Has SAE 10input
and output ports.
Can be used to intensify flow pressure when
higher pressure than pump capacity is
required
$399.00
Rotory Flow Divider
Hydraulic Cylinders
Hydraulic Cylinders
USA made, welded construction, screw in end replaceable seal type with red oxide paint, chrome plated
rods and 5-1 safety factor for bursting. Seal kits available
2”Bore x 8” Stroke x 20.25” CPCD x1.125”
Rod , Cross Tube Ends
$138.00
CYL 2x8x1.125
2”Bore x 10” Stroke x 20.25” CPCD
x1.125” Rod , Cross Tube Ends
CYL 2x10x1.125
2”Bore x 16” Stroke x 26.25” CPCD x
1.125” Rod , Cross Tube Ends
CYL 2x16x26.25
2.5”Bore x 8” Stroke x 20.25” CPCD
x1.125” Rod , Cross Tube Ends
CYL 2.5x8x20.25
2.5”Bore x 10” Stroke x 17” CPCD x1.125”
Rod , Cross Tube Ends
CYL 2.5x10x17
2.5”Bore x 14” Stroke x 21.5” CPCD x
1.25” Rod , Cross Tube Ends
CYL 2.5x14x1.25
2.5”Bore x 14” Stroke x 21.5” CPCD x 1.5”
Rod , Cross Tube Ends
CYL 2.5x14x1. 5
2.5”Bore x 16” Stroke x 22” CPCD x 00”
Rod , Cross Tube Ends
CYL 2.5x14x1. 5
3”Bore x 16” Stroke x 24” CPCD x1.5”
Rod, Cross Tube Ends
CYL 3x16x24
3”Bore x 20” Stroke x 28” CPCD x1.5”
Rod, Cross Tube Ends
CYL 3x20x28
$144.00
$177.00
$143.00
$144.00
$161.00
$191.00
$191.00
$188.00
$201.00
Hydraulic High Pressure Hoses
Hydraulic High Pressure Hoses
Three wire hoses with working pressure of 2500 psi and SAE male fittings on ends.
1/4” Diameter
Hose 1/4"x12
Hose 1/4"x18
Hose 1/4"x24
1/2” Diameter
Hose 1/2"x24"
Hose 1/2"x48
Hose 1/2"x72
3/8” Diameter
Hose 3/8"x12
Hose 3/8"x24”
Hose 3/8"x36”
Hose 3/8"x42"
Hose 3/8"x48"
Hose 3/8"x52"
Hose 3/8"x60”
Hose 3/8"x72”
Hose 3/8"x84”
Hose 3/8"x96”
Hose 3/8"x108
Hose 3/8"x120
Hose 3/8"x132
Hose 3/8"x144
Hose 3/8"x156
Low Pressure
Hose 3/8"x164
Suction Hose
To connect reservoir to pump and as low pressure
retun lines to reservoir.
0.75”ID x 1-3/8” OD 300psi working, 1200psi
bursting. Wire reinforced, neoprene cover.
$5.70
$6.45
$7.03
$10.33
$14.20
$17.55
$6.20
$7.50
$8.88
$9.69
$13.00
$11.20
$15.63
$16.75
$15.00
$16.25
$17.90
$13.00
$21.65
$23.20
$24.78
$19.00
$22.50
Power Parts
Pump Mounts
Speeds assembly time, ensures shaft alignment and improves compactness and appearance.
Pump Mount
Adapts 5 hp Briggs and Stratton Engine to
SAE “AA” 2 bolt pump.
Fabricated from aluminum.
POW#03
$98.00
Pump Mount
Adapts 10 hp Briggs and Stratton Engine
to SAE “AA” 2 bolt pump.
Fabricated from steel for greater durability.
POW#02
$98.00
Pump PTO Bracket Kit
Instructions and drawings for mounting
PTO pump using bracket kit. Kit also
contains flame cut steel bracket with 2
angles.
For SAE “B” 2 bolt pump.
(Snap adapter shown sold separately)
$50.00
Pump PTO Bracket Kit
Engines with Fuel Tanks and Mufflers
Available
18-HP Briggs & Stratton I/C
Vanguard V-Twin engine with recoil and
electronic ignition, muffler, 1 ¾ gallon fuel
tank, bracket and clamp. Has a 1” x 2
29/32” shaft, ¼” keyway; 3/8”-24 tapped
end. Use our Pump Mount (POW#02) with
this engine.
Engine-18hp
$1789.00
Briggs & Stratton I/C
Briggs & Stratton Intek 305 Industrial /
Commercial with overhead valves, cast
iron sleeve, electric and recoil start. Key
switch start and stop.
Engine- 10 hp
$929.00
Power Parts
Briggs and Stratton 10 hp Intek I/C
industrial/commercial, #
2054370041E1H1001. Used on 821 or 728
with split hydraulics
Engine-10hp
$929.00
Flex coupling to mount your engine to
pump. Synthetic rubber inserts between the
coupling halves. Available to fit ½”, ¾”
and 1” engine and pump shaft sizes.
Coupling
$29.25
Snap Adapter with a 1 3/8” x 6” spline to
mount your PTO to pump.
Bore size 7/8” , Keyway 3/16” & ¼”
Pump-PTO adapter
Gage Kit
Used to adjust the control valve to a
custom operation pressure. Includes a
pressure gage with plexiglas crystal,
aluminum dial, and white background plus
the fittings to plumb into 3/8” NPT pipe
threads.
Gage Kit
$69.95
$45.00
Gage
Pressure gage with plexiglas crystal,
aluminum dial, and white background with
NPT ¼” ports
Gage
$35.00
Breather Cap for petroleum based
products. Filters air intake into the tank.
Features glass-filled nylon construction
and polyurethane foam element.
0.75”NPT, 10 micron, 2.25” length.
HYD#03
$9.95
Power Parts
Spin-on-Filter
Filters the fine dirt from your oil line to
protect the pump and add longer life to
your hydraulic system. Has 10 micron w
¾” ports, 15 psi by-pass and max 15 gpm
for return line.
HYD#03
Weldable Black Steel Pipe Coupling
For use on oil tanks to connect to filters.
¾” Diameter
Black Coupling ¾”
Weldable Black Steel Pipe Coupling
For use on oil tanks to connect to Breather
Cap
Black Coupling 1-1/4”
$34.50
$2.50
$5.90
Suction Strainer-TMF 10 – 1¼ for freestanding CADDiggers. Filters coarse dirt
in oil line to protect the pump. Has ¾”
ports
HYD#98
$32.25
Hydraulic Wheel Motors
Speeds assembly time, ensures shaft alignment and improves compactness and appearance.
Hydraulic Motor
High Torque, Low Speed.
15.9 cu in., 1-1/4” tapered shaft, 5 bolt on
4-1/2” pattern
*****For Faster speed, less power ******
POW#03
$510.00
Hydraulic Motor
High Torque, Med Speed.
32.7 cu in., 1-1/4” tapered shaft
Max inlet pressure
1500#144
$510.00
Seats
Page 1 of 1
Seats
Seats for use on industrial, commercial, and farm equipment.
Rider Seat
Black vinyl molded cushion constructed rider
seat. Bolt pattern varies.
ACC#03
$55.00
CADTrac seat
Large seat measuring 20” wide x 21 ¾” Length
x 21 ¾” Tall. Bolt pattern is 11 ¼” x 11”.
Features slide tract with fore & aft adjustment.
Constructed for air circulation and water
drainage. Fits CADTrac and 99%of existing
forklift and other material handling and
construction equipment.
ACC#10
$368.00
Bucket Teeth
Parts for use on industrial, commercial, and farm equipment
Bucket Tooth & Holder Assembly
Used on all CADDiggers.
821#H09
$35.19
Loader Tooth & Holder Assembly
Can be used on all Loaders.
Loader Tooth Assembly
$43.20
Trailer Coupler
Shelby 2” coupler for 2” Tongue with 3500 lb
max capacity
821#65
Grease Fittings
Provides a grease port into hydraulic cylinders
for long term maintenance. Simply drill an 1/8”
hole in each end of cylinder at a convenient
location for adding grease, then screw in the
grease fittings tightly.
Pkg contains qty 15
ACC#02
$19.25
$9.00
Seats
Page 2 of 2
Cutting Edge
High Carbon (above 0.5% carbon), beveled steel, rolled formed to shape for greater strength.
Note: Must be welded with low hydrogen rods such as 7018.
3/8” x 3” x 4” length.
Cutting Edge - 4
3/8” x 3” x 6.5” length.
Cutting Edge – 6.5
3/8” x 3” x 10” length.
Cutting Edge - 10
3/8” x 3” x 12” length.
Cutting Edge - 12
3/8” x 3” x 13” length.
Cutting Edge - 13
3/8” x 3” x 15.75” length.
Cutting Edge – 15.75
3/8” x 3” x 18” length.
Cutting Edge - 18
3/8” x 3” x 48” length.
Cutting Edge - 48
Top Link Cat II
CAD II – Adjustable from 21” to 33”, thread 11/8”NC. 1” sockets. For CADTrac
1500#137
Top Link Cat 0 & Cat I
CAD I – For CADDigger 710/810/610.
Top Link Cat I
Lift Arm Draw Pins
Cad I Adjustable 7/8” diameter, 6.25” length.
ACC#40
Lift Arm Draw Pins
Cad 0 Adjustable 5/8” diameter, 4.00” length.
ACC#41
Lift Arm Draw Pins
Cad II Adjustable 1-1/8” diameter, 6.25” length.
ACC#42
$9.77
$16.15
$24.48
$29.32
$31.79
$38.16
$44.20
$117.30
$68.45
$68.45
$9.50
$7.50
$11.50
Lock Nut for CAT II TopLink
1500#138
$4.45
Threaded Repair end for CAT II Top Link
Right handed 1-1/8”, Socket has 1” bore with 11/8”dia handle x 7 threads
1500#143
Hitch Pins-Bent
5/8” diameter x 5 ¼” long, bent, with keeper.
ACC#03
Hitch Pins-Straight
5/8” x 4 ½” usable length with keeper.
ACC#04
Hitch Pins-Straight
7/8” x 6” usable length with keeper.
801#09
$38.95
$7.60
$7.60
$9.90
Seats
Page 3 of 3
Top Link Pins
Cad I ¾” diameter, 6-3/8” length.
ACC#50
Top Link Pins
Cad II, 1”diameter, 6” length.
ACC#51
$7.25
$8.75
Cable Ties
Extra Heavy Duty, 14” long, Pkg contains qty
15
ACC#01
$7.00
CAD II Replacement End
Replacement Weld-on ball joint for Cad II
Toplink.
1500#107
$32.50
Tires and Wheels
Tires and Wheels
Tires and wheels for use on industrial, commercial, and farm equipment
Skid Steer Tire & Wheel
Size 27-8.5-15 4 ply skid steer type tires
with heavy duty tread for maximum
stability and improved clean out. Unique
lug give superior traction in any soil.
Reinforced sidewall protects rim and
prevents tears and punctures. Mounted on
wheels with a 5 hole, 4 ½” bolt pattern.
Used on CADTrac.
1500#146
$199.00
Tire & Wheel
Tire, size 15, mounted on dex white
spoke wheels with a 5 hole, 4 ½” bolt
pattern. Used on CADDigger 628, 728,
821 and 841.
ACC#06
$115.00
Tire & Wheel - Towing
Tire, size 20.5 x 8.5 x 10 with a 5 hole, 4
½” bolt pattern. Used on CADDigger
841. (refn:841#51)
ACC#20
$94.00
Tire & Wheel – Pivot
Tire, size 4.8, mounted on wheels with a
8.5 x 4 ½” bolt pattern . 2500 lb. capacity.
Used as pivot wheels on CADDigger 841.
(refn:841#71)
(Hub not included)
ACC#23
$55.00
Tires and Wheels
Wheel Hubs
Fit Size 15 tires with 5 hole, 4 ½” bolt
pattern. Includes bearings, seal, cap, nuts,
washer, cottor pin. (Order with stub axle
ACC#06.) Used on CADDigger 628, 728,
and 821.
ACC#07
Wheel Hubs - Pivot
Fit Pivot tires with 5 hole, 4 ½” bolt
pattern. Includes bearings, seal, cap, nuts,
washer, cottor pin. (Order with stub axle
ACC#21.) Used on CADDigger 628, 728,
and 821.
ACC#22
Stub Axle
1 ¾” round, 4” shank . (order with wheel
hub ACC#07) Used on CADDigger 628,
728, 821, and 841.
ACC#08
Stub Axle - Pivot
1.25” round, 4” shank . (order with wheel
hub ACC#22) Used on CADDigger 841
refn:841#51
Acc#21
$48.50
$38.50
$24.30
$23.00
Bearings Pins Tubing
Nylatron Bearings
Nylatron bearings are molybednum impregnated to lubricate over the lifetime of the bearing. Can be
greased for even longer bearing life.
Nylatron Bearing
$9.20
1-1/2”OD x 1”ID x 3”length
NyB15x3
Nylatron Bearing
1-1/2”OD x 1”ID x 3.5”length
$9.20
NyB15x3.5
Nylatron Bearing
1-1/2”OD x 1”ID x 4”length
$10.35
NyB15x4
Nylatron Bearing
2”OD x 1.5”ID x 3”length
$9.20
NyB2x3
Nylatron Bearing Plate
4 x 4 with a 2” hole
$6.45
NyBPlate
Pins to fit Mechanical Tubing
Undersized to make a tight fit in the 1” or 2” ID of mechanical tubing
1” Pins
Pins
63/64” diameter pin stock, 6” length
$6.00
Pin1x6
Pins
63/64” diameter pin stock, 7” length
$7.00
Pin1x7
Pins
63/64” diameter pin stock, 9” length
$7.80
Pin1x9
Pins
63/64” diameter pin stock, 13” length
$11.65
Pin1x13
Pins
63/64” diameter pin stock, 17” length
$14.10
Pin1x17
Pins
63/64” diameter pin stock, 36” length
$25.65
Pin1x36
Pins
63/64” diameter pin stock, Custom Cut $1.00/in
$1.00
Pin1xCustom
Pins 1.5”
Pins 1.5”
1-31/64” diameter pin stock, 8” length
$9.05
Pin15x8
Pins 1.5”
1-31/64” diameter pin stock, 9” length
$10.30
Pin15x8
Pins 1.5”
1-31/64” diameter pin stock, 17” length
$18.10
Pin15x17
Pins 1.5”
1-31/64” diameter pin stock, 36” length
$37.00
Pin15x36
Pins 1.5”
1-31/64” diameter pin stock, Custom Cut at
$1.25 / inch
Pin15xCustom
$1.25
Bearings Pins Tubing
Mechanical Tubing
DOM Tubing sized to fit with pins tightly
2.5” Mechanical Tubing:
Mechanical Tubing
2.5”OD x ¼” wall x 5.5”
$11.00
MechT25x5.5
Mechanical Tubing
2.5”OD x ¼” wall x 6”
$11.25
MechT25x6
Mechanical Tubing
2.5”OD x ¼” wall x 10”
$16.10
MechT25x10
Mechanical Tubing
2.5”OD x ¼” wall x Custom Cut $2.00/inch
$2.00
MechT25xCustom
2” Mechanical Tubing:
Mechanical Tubing
2”OD x 1.5”ID x 10”
$17.50
MechT2x10
Mechanical Tubing
2”OD x 1.5”ID x Custom Cut at $2.25 / inch
$2.25
MechT2xCustom
1.5” Mechanical Tubing:
Mechanical Tubing
1-1/2”OD x ¼”wall x 3/4”
$1.65
MechT15x1
Mechanical Tubing
1-1/2”OD x ¼”wall x 1”
$1.65
MechT15x1
Mechanical Tubing
1-1/2”OD x ¼”wall x 1.25”
$1.90
MechT15x1.25
Mechanical Tubing
1-1/2”OD x ¼”wall x 1.5”
$2.25
MechT15x1.5
Mechanical Tubing
1-1/2”OD x ¼”wall x 12”
$18.00
MechT15x12
Mechanical Tubing
1-1/2”OD x ¼”wall x 18”
$19.50
MechT15x18
Mechanical Tubing
1-1/2”OD x ¼”wall x 3”
$4.50
MechT15x3
Mechanical Tubing
1-1/2”OD x ¼”wall x 4”
$6.00
MechT15x4
Mechanical Tubing
1-1/2”OD x ¼”wall x 5”
$7.50
MechT15x5
Mechanical Tubing
1-1/2”OD x ¼”wall x Custom Cut at $1.50/inch
MechT15xCustom
$1.50
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising