External Wireless Sounder

External Wireless Sounder
External Wireless
Sounder
WL S50
Installation and Programming Instructions
2
Wireless Sounder Instructions
Table of Contents
Introduction........................................................................................................... 4
Operational Functions.......................................................................................... 4
Alarm / Tamper Indication ...................................................................................4
Low Battery Indication.........................................................................................4
Supervision .........................................................................................................4
Pre Alarm Indication............................................................................................4
Sounder Self Testing...........................................................................................4
LED display.........................................................................................................4
Mounting the Sounder.......................................................................................... 5
Programming the sounder ................................................................................... 6
Step 1: Sounder/Receiver Communication Set up..............................................6
Step 2: Setting the Sounder Parameters.............................................................7
Strobe Control ............................................................................................... 7
Strobe Blink ................................................................................................... 7
Strobe Arm Squawk ...................................................................................... 7
Adjusting the Volume .................................................................................... 7
Muting Tamper .............................................................................................. 7
Setting Supervision Time .............................................................................. 8
Pre Alarm indication ...................................................................................... 8
Step 3: Testing the Sounder ...............................................................................8
Communication Test ..................................................................................... 8
Diagnostics.................................................................................................... 8
Replacing Batteries .............................................................................................. 9
Technical Information........................................................................................... 9
Electrical .............................................................................................................9
Wireless ..............................................................................................................9
Environment........................................................................................................9
Wireless Sounder Instructions
3
Introduction
RISCO Group's two-way External Wireless Sounder is designed to extend the
signaling capabilities of the RISCO Group WisDom and Agility wireless systems,
within the protected area. The wireless sounder offers an easy and flexible solution
for quick installation. The sounder is powered with its own batteries and
communicates wirelessly with the security panel using 868MHz frequency band.
Up to 3 wireless sounders can be assigned to a system.
Operational Functions
Alarm / Tamper Indication
Upon an alarm condition, the sounder will be activated for a period of time defined
by the system (Bell Time Out parameter).
The maximum time that the sound will be activated is 5 minutes.
Low Battery Indication
Upon a low battery condition a fault indication is sent to the panel.
There are 2 types of low battery indications:
Ê Radio low battery
Ê Speaker low battery
Supervision
Each sounder can be defined to be supervised by the panel. The system generates
a local fault signal identifying the sounder whose signal is not received during a
predefined time, followed by a report to the Alarm Receiving Center (if defined).
Pre Alarm Indication
When an entry time starts, the system transmits a pre-alarm signal to the sounder.
If the system is unset before the entry delay time expires, a cancellation signal is
sent to the sounder.
If the sounder does not receive a cancellation signal within the entry delay time, the
sounder will be activated.
Sounder Self Testing
Once placing all batteries in the battery holders or pressing on the reset switch
located on the PCB (with the tamper switch open), the sounder performs a
functional self test indicated by a strobe flash squawk sound.
LED display
The wireless sounder has 2 LEDs located on the PCB. These LEDs are
enabled when the tamper is open and 10 minutes after the tamper is closed.
Red: Indicates transmission
Yellow: Indicates a low battery
Red and Yellow (3 seconds): Confirms successful learning
4
Wireless Sounder Instructions
Mounting the Sounder
1) Open the screw cover by
applying thumb pressure on
the screw cover lower part.
When raised, push outwards.
Once you have gained
access to the cover screw,
open screw and lift the cover
away until cleared from the
back plate.
Siren cover
screw
Screw cover Lower section
Cover - Exploded View
2) Once the cover has been removed it
may be slid into one of the Cover
Holder Clips. This is done by
placing the cover next to the cover
holding clips and then sliding it into
place. To release cover, press the
release tab and slide cover out.
3) To reach the PCB release the inner
cover and lift the cover until it locks
in the raised position.
Retaining Clip Inner Cover
Tab
Release Tabs
Sliding pattern of Tab
into the Cover holder clips
Cover Holder
Clips
4) Position the sounder base plate against the wall and mark the securing holes
according to the strobe required position. The unit should be mounted to the wall
using at least three 2" No 10 screws and suitable wall anchors.
Fixing points with
strobe at the top
Fixing points with
strobe at the bottom
Strobe
Strobe
5) Insert the supplied batteries in the metal clips according to the polarity.
6) The sounder is ready for communication set up with the system.
7) Once the communication set up is completed, close the inner cover and reattach the
outer cover.
Wireless Sounder Instructions
5
Two Indication
LEDs
Reset Switch
Radio Batteries
(3V, Parallel
Connection)
TAMPER SPEAKER
Speaker
Speaker & Strobe
Batteries
(6V, Serial
Connection)
Strobe
LEDS
External Sounder - PCB Diagram
Programming the sounder
Programming the wireless sounder consists of the following 3 steps:
1. Setting communication between the receiver and the sounder
2. Setting sounder parameters
3. Testing the sounder
Step 1: Sounder/Receiver Communication Set up
The sounder must identify itself to the system's receiver by writing its ID into the
system. Perform the following steps:
1. Set the receiver to the Write mode.
NOTE:
In the WisDom , as a first step, you need to allocate the sounder in the following programming location:
Main engineer menu> 9) Devices > 2)Sounder > 1) Allocation > Select sounder> Choose ODWS1
2.
3.
4.
5.
Select the sounder's ID.
Unpack the supplied batteries
Insert two speaker batteries and three Radio batteries into the batteries' holders.
After a squawk is heard and the sounder's strobe flashes you have 10 seconds to
press on the tamper switch for at least 3 seconds. If the sounder is successfully
recognized, the system will sound a confirmation beep and the sounder will initiate
a second squawk sound and the 2 LEDs on the sounder will flash for 3 seconds.
6. Repeat the process for other sounders in the system.
6
Wireless Sounder Instructions
Step 2: Setting the Sounder Parameters
Each sounder can be defined with different sets of parameters. The table below
describes the list of parameters of the sounder.
NOTE:
For the specific programming location of each parameter refer to the system manuals.
Strobe Control
Defines the Strobe operation mode:
¾ Always Off: The strobe is deactivated
¾ Follow Bell (Default): The strobe is activated when the sounder bell is
triggered.
¾ Follow Alarm: The strobe is activated when an alarm event occurs in the
system.
Strobe Blink
Defines the number of times that the strobe will flash per minute (Default 40 times per
minute). Strobe Blink options:
[1] 20 times per minute
[4] 50 times per minute
[2] 30 times per minute
[5] 60 times per minute
[3] 40 times per minute (Default)
Strobe Arm Squawk
The time that strobe blinking will continue when set is performed (Default: 05)
NOTE:
If the sounder’s squawk strobe is defined as NO (Refer to Allocation section) this parameter will be ignored.
Adjusting the Volume
Defines the sounder sound volume for the following system modes:
¾ Exit / Entry: The sound produced during Exit/Entry time (Default: 0)
¾ Alarm: The sound produced during alarm (Default: 9)
¾ Squawk: The sound produced during squawk sounds (Default: 9)
The sound volume range is between 0 (silent) to 9 (maximum volume).
Muting Tamper
This feature disables a tamper alarm from the sounder and it is recommended to be
used when replacing the sounder's batteries.
NOTES:
1. An ongoing tamper alarm will not be disabled.
2. WisDom: This feature is controlled under the Engineer Menu (Quick key [9][2][5]). Tamper alarm
will be disabled during the current installation programming period.
3. Agility: This feature is controlled under the Grand Master menu. Tamper alarm will be disabled for
20 minutes.
Wireless Sounder Instructions
7
Setting Supervision Time
Specifies how often the system generates a supervision request to the sounder.
If any of the sounders does not respond to the request at least once, during the
receiver supervision time, the system will regard the accessory as lost.
NOTE:
The receiver supervision time should be higher than the sounder supervision time in order to
eliminate false lost event.
Range: 00-255 minutes
Default: 58 minutes
NOTE:
WisDom: Engineer menu: 1) System > 1) Timers > 9) Accessory supervision time
Agility: Engineer menu: 1) System > 1) Timers > TX supervision
Pre Alarm indication
This wireless sounder incorporates a pre-alarm feature that enhances the security of
the system, by producing a local alarm in case of sabotage.
If defined, the system sends a pre-alarm signal to the sounder at the beginning of the
entry delay. If the sounder does not receive a cancellation signal from the system at
the end of the entry time, the sounder goes into alarm mode.
NOTE:
WisDom (Ver 4.25): Engineer menu Quick key: 1)System> 2)Parameters> 35)Sounder Pre alarm
Agility: Engineer menu: [1][2] > Advanced > Sounder Pre alarm
Step 3: Testing the Sounder
Communication Test
The sounder communication test performs a communication test between the sounder
receiver and the system.
¾ To perform a communication test:
1. Access the communication test option.
NOTE:
WisDom: Engineer menu > 9) Devices > 2) Sounders > 3) Communication test
Agility: Engineer menu > 2) Testing > 5) Sounder > 1) Communication test
2. The system sends a test signal to the sounders. A number between 00-99 indicates
the strength of the communication signal between the system and the sounder.
NOTE:
For successful communication, the strength of the signal should be higher that the sounder receiver noise
threshold level.
(WisDom: Engineer menu quick key [9][2][4], Agility: Engineer menu > 2)Testing >1)Main unit >
1)Calibration).
Diagnostics
The Diagnostics menu enables to test parameters reflecting the operation of the
sounder:
Ê Speaker batteries voltage: Tests the selected sounder’s speaker batteries voltage
Ê Radio batteries voltage: Tests the selected sounder’s radio's batteries voltage
Ê Sounder version: Displays information regarding the sounder's version
8
Wireless Sounder Instructions
NOTE:
WisDom: User menu: 4) Maintenance > 7) Sounders > 1) Diagnostics
Agility: Engineer menu > 2) Testing> 5) Sounder>2) Battery test > 3)Version
The diagnostic features can also be performed from the Upload/Download software, locally or
remotely.
Replacing Batteries
1.
2.
3.
4.
5.
Before opening the sounder it is advised to silence the tamper alarm using the
Tamper Mute option.
Remove the screws on both sides of the external wireless sounder and open the
cover of the sounder upwards.
Insert the batteries supplied.
Remove the old batteries from the metal clips and replace them with the new ones.
Pay attention to the polarity.
Replace the cover and lock the screws.
NOTES:
Dispose of old batteries according to your local regulations.
Risk of explosion if battery is replaced by an incorrect type.
Technical Information
Electrical
Power supply
Battery lifetime
Sounder volume
Strobe lens
Flash frequency
Dimensions (HxWxD)
Weight (including batteries)
5 x CR123, 3V Lithium batteries
3 batteries for the wireless system
2 batteries for signalling
3 years (typical)
105 dB @ 1 meter (adjustable)
Polycarbonate
60 times per minute (max.)
300x 325x70 mm (11.8 x 12.8 x 2.8 inch)
1 Kg
Wireless
Wireless technology
Frequency
Range
Monitoring
Modulation Type
Bidirectional narrow band
868 / 433MHz
150m (492’) Line of sight
YES
ASK
Environment
Temperature range
IP class
Environment class
- 25°C to 60°C (-4°F to 140°F)
IP 44
Class IV
Ordering Information
Part Number
WL S50
Description
2 way External Wireless Sounder, 433 / 868.65 MHz
Specifications are subject to change without prior notice. Should any questions arise please contact your
supplier.
Wireless Sounder Instructions
9
RTTE Compliance Statement
Hereby RISCO Group declares that this wireless sounder is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
For the CE Declaration of Conformity please refer to our website: www.riscogroup.com.
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and receiver.
c) Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
d) Consult the dealer or an experienced radio/TV technician.
FCC ID: JE4RWRT433 valid for model WL S50
IC: 6564A-RWRT433 valid for model WL S50
FCC Warning
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
RISCO Group Limited Warranty
RISCO Group Ltd. and its subsidiaries and affiliates ("Seller") warrants its products to
be free from defects in materials and workmanship under normal use for 24 months
from the date of production. Because Seller does not install or connect the product and
because the product may be used in conjunction with products not manufactured by
the Seller, Seller cannot guarantee the performance of the security system which uses
this product. Seller's obligation and liability under this warranty is expressly limited to
repairing and replacing, at Seller's option, within a reasonable time after the date of
delivery, any product not meeting the specifications. Seller makes no other warranty,
expressed or implied, and makes no warranty of merchantability or of fitness for any
particular purpose.
In no case shall seller be liable for any consequential or incidental damages for breach
of this or any other warranty, expressed or implied, or upon any other basis of liability
whatsoever.
Seller's obligation under this warranty shall not include any transportation charges or
costs of installation or any liability for direct, indirect, or consequential damages or
delay.
Seller does not represent that its product may not be compromised or circumvented;
that the product will prevent any personal injury or property loss by burglary, robbery,
fire or otherwise; or that the product will in all cases provide adequate warning or
protection. Buyer understands that a properly installed and maintained alarm may only
reduce the risk of burglary, robbery or fire without warning, but is not insurance or a
guaranty that such will not occur or that there will be no personal injury or property loss
as a result.
Consequently seller shall have no liability for any personal injury, property damage or
loss based on a claim that the product fails to give warning. However, if seller is held
liable, whether directly or indirectly, for any loss or damage arising from under this
limited warranty or otherwise, regardless of cause or origin, sellers maximum liability
shall not exceed the purchase price of the product, which shall be complete and
exclusive remedy against seller.
No employee or representative of Seller is authorized to change this warranty in any
way or grant any other warranty.
WARNING: This product should be tested at least once a week.
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact
us through our website www.riscogroup.com or as follows:
United Kingdom
Tel: +44-161-655-5500
technical@riscogroup.co.uk
USA
Tel: +1- 631-719-4400
support-usa@riscogroup.com
Italy
Tel: +39-02-66590054
support@riscogroup.it
Brazil
Tel: +1-866-969-5111
support-br@riscogroup.com
Spain
Tel: +34-91-490-2133
support-es@riscogroup.com
China
Tel: +86-21-52-39-0066
support-cn@riscogroup.com
France
Tel: +33-164-73-28-50
support-fr@riscogroup.com
Poland
Tel: +48-22-500-28-40
support-pl@riscogroup.com
Belgium
Tel: +32-2522-7622
support-be@riscogroup.com
Israel
Tel: +972-3-963-7777
support@riscogroup.com
All rights reserved.
No part of this document may be reproduced in any form without prior written
permission from the publisher.
© RISCO Group 07/09
5INRWS50 D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising