Essence Food processor HR7754/01
Essence
Food processor
HR7754/01
Philips Consumer Lifestyle
Service Manual
PRODUCT INFORMATION
TECHNICAL INFORMATION
- The Foodprocessor is equipped with mechanical and
thermal safety switches.
- Motor
Materials used:
- Bowl, bowl lid, JE lid
blender jar & safety cover,
- Housing, screw cap, blender lid,
pusher, inlay bowl handle
- juice extractor (sieve, pusher),
citrus press (sieve & cone)
- Panel foil
- Kneading accessory
- Balloon beater
- Insert holder, handgrip blender jar
- Adjustable slicing disc
: SAN
: PP
: PP
:
:
:
:
:
Santoprene
PP / 30% chalk
POM
ABS
POM, ABS,
stainless steel
: universal, radio / TV interference
suppressed
- Power consumption : 800 Watt max.
- Voltage & frequency : 230 V, 50 Hz
- Cordset
: 100 cm, double insulated with
moulded on plug
- Speed setting
: Smart Process Control
- Bowl capacity
: 2.5 L dry ingredients, 1.7 L liquids
- Blender capacity
: total jar capacity 2.0 L,
1.5 L effective
- Speeds unloaded
: blender drive shaft 19500 rpm (max)
accessories drive shaft from 660 rpm
to 2150 rpm, depends on application
- Weight in fancy box : 6.200 g
- Dimensions
: 406 mm x 281 mm x 521 mm
fancy box (l x w x h)
Colours:
- White with Vapor Dusk accents, clear transparant
bowl & jar
Safety:
- Automatically resettable : protects motor against
thermal cut out
overheating
- Built – in safety lock
: detects wheter lid & bowl are
assembled
- Motor brake system
: stops the appliance within
1.5 seconds
- This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
Published by Philips Consumer Lifestyle
09/11
Printed in the Netherlands
© Copyright reserved
Subject to modification
REPAIR INSTRUCTIONS
HR7754/01
Safety lock (item 7)
Place the lid on the bowl in the right position. The appliance
will only function if the line on the applinace is directly
opposite the mark on the lid of the food processor bowl and
the same holds for the other accessoires. The built-in safety lock
will now be deblocked and you can turn the appliance on.
Note that if both the blender jar and the bowl have been
correctly mounted, only the blender will function.
- The blender coupling on the motor shaft has been provided
with a customary left-handed thread.
The drive coupling (item 10) can be detached by means of
a hammer and a screwdriver. Strike the screwdriver with a
short sharp blow and remove the drive coupling, or block
the acc. drive wheel (item 17) and thereby the rotor shaft,
by sticking a pin through the hole (5 mm dia. – marked
with an arrow) in the bottom plate.
- The assembly of the accessories depends on the national
version.
- For specific versions, the component configuration may
differ from the one shown on the exploded view. However,
the actual components can be distinguished by their code
numbers.
- Make sure that all functions, including the safety devices,
are working correctly after you have completed the repair.
- To check the processes of smart control, please look at the
described functions on the next page.
Important:
If the appliance is used without the blender jar, the appliance
will not function, when the blender coupling (item 10) has not
been protected by the blender cover (item 1).
Note:
The blender cover can only be removed, when the bowl
including the bowl lid is not mounted on the foodprocessor.
How to set the belt tension:
Step 1: Give 30 N pretension force on the adjusting plate to
minimise the distances between the belt and the belt
wheels
Step 2: Reduce the tension force from 30 N down to 10 N
which is the required belt drive force for the appliance.
Step 3: Fix the adjusting screw on the adjusting plate when the
tension force reaches the value of 10 N (after coming
down from 30 N!)
Automatic resettable cut-out (part of item 11)
To prevent damage due to overheating, the appliance has been
equipped with an automatic cut-out system.
This system will automatically cut off the power supply when
the appliance overheats.
If the appliance suddenly stops running:
- Unplug the appliance
- Switch off the appliance
- Let the appliance cool down for 15 minutes
- Plug the appliance in again
- Switch the appliance on again
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- No specific issues
OPTIONAL (accessories)
- No specific issues
F1
red
brown
MAINS
R10
C1
U
F2
black
red
white
S1
yellow
Rotor
S2
yellow
Main PCB
Change-over switch
in braking position
2-7
PROCESSES
SMART
CONTROL
SMART
CONTROL
SMART
CONTROL
SMART
CONTROL
SMART
CONTROL
SMART
CONTROL
SMART
CONTROL
HR7754/01
Chopping process
The chopping process starts with four pulses. After that, the food processor will pick up speed until it
runs at maximum power. He will continue to run at this speed until the STOP button is pressed.
The speed can be decreased in three steps by pressing the - button.
Shredding and slicing process
When the shredding and slicing button is pressed, the food processor will start to run at a constant
speed to produce the best end results with the adjustable slicing disc or the inserts.
The food processor will continue to run at this constant speed until the STOP button is pressed.
The speed can be increased or decreased in three steps by pressing the + button or - button.
Kneading process
The kneading process starts with a Soft Start and then increases to a powerful kneading speed to
achieve a good end result in a short time. The food processor will continue to run at this speed until
the STOP button is pressed. The speed can be decreased in three steps by pressing the - button.
Whisking process
When the whisking process is selected the appliance starts with a 10 second Soft Start. The speed will
gradually increase until the maximum working speed for perfectly whisked egg whites or whipped
cream has been reached. The speed is maintained until the STOP button is pressed.
The speed can be decreased in three steps by pressing the - button.
Blending process
To prevent splashing, the blending process features a Soft Start.After a few seconds the speed gradually
increases to maximum speed to produce a perfectly smooth result. The blender will continue to run at
this speed until the STOP button is pressed. During the biending process the speed can be decreased in
three steps by pressing the -button.
Citrus pressing process
The citrus pressing process features a Soft Start, which means the cone starts rotating at a low speed
guaranteeing a pieasant sensation and a perfect result. The food processor will continue to run at this
speed until the STOP button is pressed. The speed can be decreased in three steps by pressing the
-button.
Juice extracting process
The juice extracting process has a Soft Start, which means that the juice extractor will start to run at
a low speed and gradually increase to maximum speed to guarantee the highest possible, juice output.
The food processor will continue to run at this speed until the STOP button is pressed.
The speed can be decreased in three steps by pressing the -button.
3-7
PARTS LIST
Pos
Service code
1
2
3
4
5
HR7754/01
Description
Pos
Service code
Description
4203 065 63470
4203 065 63620
4203 065 63950
4203 065 63910
4203 065 63890
Blender cover
Screw cap
Top housing printed
Panelfoil assy
PCB controll assy
30
31
32
33
34
4203 065 63880
4203 065 63870
4203 065 63800
4203 065 63760
4203 065 63770
Press cone
Sieve
Pusher closed bowl
Bowl lid
Lid bearing
6
7
8
9
12
4203 065 63490
4203 065 63580
4203 065 63960
4203 035 53570
4203 065 63590
Housing parts
Safety switch lever
PCB brake
Motor / Coupling – Assy
Motor coupling assy
35
39
40
42
43
4203 065 63780
4203 065 61570
4203 065 61550
4203 065 61560
4203 065 62310
Closed bowl
Insert granulating
Insert shredding fine
Insert shredding medium
Insert shredding coarse
13
14
15
16
17
4203 065 63600
4203 065 63540
4203 065 60310
4203 065 65460
4203 065 63560
Mounting plate
Adjusting piece
Motor screw
Tooth belt
Belt wheel
44
45
46
47
48
4203 065 61520
4203 065 63670
4203 065 63970
4203 065 63690
4203 065 63660
Insert holder
Adjustable slicing disc
Plastic kneader
Metal knife
Emulsifing disc
18
19
4203 065 63610
4203 065 65340
4203 065 64000
4203 065 64020
Single speed gear
Cordset EURO
Cordset UK
Cordset SWISS
49
50
54
60
61
4203 065 63680
4203 065 61350
4203 035 90560
4203 065 63820
4203 065 63830
Toolholder
Ballon beater assy
Blender jar Assy
Juice extractor pusher
Juice extractor lid
62
63
4203 065 63840
4203 065 65760
Juice extractor lid bearing
Juice extractor accessory
Caused by Callrate at the Juice extractor accessory due to the possibility, that the consumer was able to assemble
it in a wrong way, some modifications have been done. The concerned parts are the shredding piece and the
sieve, which are now combined to an assy (Pos. 63). This was necessary, due to the non-interchangeability
between the old and new parts.
= changed
4-7
EXPLODED VIEW
HR7754/01
1
2
3
7
4
5
8
6
5-7
EXPLODED VIEW
HR7754/01
19
9
12
18
13
14
15
16
17
6-7
EXPLODED VIEW
HR7754/01
39
60
30
40
42
31
43
62
61
44
32
45
63
50
46
33
34
47
54
35
48
49
7-7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising