Instruction Manual
EN
Instruction Manual
Congratulations on the purchase of your ECOVACS Robotics WINBOT!
We hope it brings you many years of satisfaction. We trust the purchase of your
new robot will help keep your home clean and provide you more quality time to
do other things.
Live Smart. Enjoy Life.
Should you encounter situations that have not been properly addressed in
this Instruction Manual, please contact our Customer Service Center where a
technician can address your specific problem or question.
For more information, please visit the ECOVACS official website: www.ecovacs.com
The company reserves the right to make technological and/or design changes
to this product for continuous improvement.
Thank you for choosing WINBOT!
Contents
1. Important Safety Instructions.......................................................................2
2. Package Contents and Technical Specifications.......................................4
2.1 Package Contents.....................................................................................4
2.2 Specifications............................................................................................4
2.3 Product Diagram........................................................................................5
3. Operating the Robot......................................................................................6
3.1 Notes Before Cleaning ..............................................................................6
3.2 Attach the Cleaning Pad ...........................................................................7
3.3 Assemble the Power Adapter.....................................................................7
3.4 Install the Safety Tether.............................................................................7
3.5 Place the Safety Pod ................................................................................9
3.6 Spray Cleaning Solution............................................................................9
3.7 Start.........................................................................................................10
3.8 Pause......................................................................................................11
3.9 Stop.........................................................................................................12
4. Maintenance.................................................................................................13
4.1 Cleaning Pad.......................................................................................... 13
4.2 Cupule, Sensors, Squeegee, Corners.....................................................13
4.3 Driving Treads.........................................................................................14
5. Status Indicator Light and Sounds ............................................................15
6. Troubleshooting...........................................................................................16
1. Important Safety Instructions
When using an electrical appliance, basic precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
SAVE THESE INSTRUCTIONS
1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge
on proper use. Supervision may be necessary. Do not allow children to play with the
Appliance.
2. Do not use the Appliance in extremely hot or cold environments (below 0˚C/32˚F or above
40˚C/104˚F). The Appliance can be used to clean outside windows if it is properly tethered
to the Safety Pod, winds are calm, and it is not raining or snowing.
3. Please ensure the Appliance is plugged in while it is cleaning. The Appliance has a Back-Up
Battery that charges during use. The Back-Up Battery powers the Appliance if it becomes
unplugged or the electricity fails.
4. Do not leave the Appliance unattended when it is plugged in.
5. For household use ONLY. Do not use the Appliance in commercial or industrial environments.
6. Do not use the Appliance on cracked glass.
7. Only use accessories recommended or supplied by the manufacturer. Only use the Power
Adapter supplied by the manufacturer.
8. Please make sure your power supply voltage matches the power voltage marked on the
Power Adapter.
9. Do not use the Appliance on a framed window with a frame smaller than 5mm (0.2 inches).
10. Do not use the Appliance on wet or greasy windows.
11. Store the Appliance away from heat and flammable materials.
12. Do not use the Appliance if it does not firmly attach to the glass or has visible signs of damage.
13. To reduce the risk of electrical shock, do not put the Appliance in water or other liquid. Do
not place or store Appliance where it can fall or be pulled into a tub or sink.
14. Do not touch power plug or the Appliance with wet hands.
15. Do not charge the Appliance in extremely hot or cold environments, or it may affect battery
life span.
16. When charging the Appliance, do not place it on other electrical appliances and keep it
away from fire and liquid.
17. Take care not to damage the power cord. Do not pull on or carry the Appliance by the power
cord, use the power cord as a handle, close a window on the power cord, or put heavy
weights on the power cord. Keep power cord away from hot surfaces.
18. Do not use with a damaged power cord or receptacle. Do not use the Appliance if it is not
working properly, has been dropped, damaged, or come in contact with water. It must be
repaired by the manufacturer or its service agent in order to avoid a hazard.
19. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
in order to avoid a hazard.
20. The plug must be removed from the receptacle before cleaning or maintaining the Appliance.
Do not unplug the Power Adapter by pulling on the power cord.
21. The Back-Up Battery must be replaced by the manufacturer or its service agent in order
to avoid a hazard.
22. The Back-Up Battery must be removed and discarded according to local laws and regulations
before disposal of the Appliance.
23. The Appliance must be disconnected from the receptacle before removing the battery for
disposal of the Appliance.
2
EN
1. Important Safety Instructions
24. Please dispose of used batteries according to local laws and regulations.
25. Do not incinerate the Appliance even if it is severely damaged. The battery can explode in
a fire.
26. The Appliance must be used in accordance with the directions in this Instruction Manual.
The company cannot be held liable or responsible for any damages or injuries caused by
improper use.
For EU Countries
Correct Disposal of this product
This marking indicates that this product should not be disposed of with other household
waste throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To recycle your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can safely recycle
this product.
EN
3
2. Package Contents and Technical Specifications
2.1 Package Contents
DE
IT
FR
EN
Benutzerhandbuch
Manuale d’Istruzione
Mode d'emploi
Instruction Manual
WINBOT 9
Power Adapter
Instruction Manual
Safety Pod and
Tether
(3) Cleaning Pads
WINBOT
Cleaning Solution
(1) WINBOT
Extension Cord
(1.5m/4’11”)
Finishing Cloth
Remote Control
with Batteries
2.2 Specifications
Model
Working Voltage
W930
15V DC
Rated Power
35W
Remote Control
3V DC
Input Voltage
Power Adapter:WT1503000
Input:100-240V AC 50/60Hz 1.6A
Output:15V DC 3.0A
* Technical and design specifications may be changed in the course of continuous product improvement.
4
EN
2. Package Contents and Technical Specifications
2.3 Product Diagram
Robot
6
7
8
1
2
3
9
10
11
12
13
4
5
14
1. Power Cord
2. Handle
3. Status Indicator Light and
START/PAUSE Button
4. Air Release Trigger
5. Cleaning Pad Plate
6. Squeegee
7. Cupule
8. Driving Treads
9. Wheel Sensor
10. Bottom Status
Indicator Light
11. Bottom Power Switch
12. Edge Detection
Sensors
13. Cleaning Pad
14. Cleaning Pad Velcro
Remote Control
1
2
3
1. RESET Button
2. Direction Control Buttons
3. START/PAUSE Button
4. Remote Control Pairing Button
4
EN
5
3. Operating the Robot
3.1 Notes Before Cleaning
35
60
Do not use WINBOT 9 on a framed window
with frame smaller than 5mm (0.2").
WINBOT 9 can be used to clean framed or
frameless glass, larger than 35cm x 60cm
(13.8’’ x 23.6’’).
If WINBOT 9’s Status Indicator Light
If the window is fully covered with dirt, clean
flashes GREEN after powering ON, the
a small area on the glass before use and
Back-Up Battery requires charging. Keep
place WINBOT 9 there.
WINBOT 9 plugged in to charge the BackUp Battery until the Status Indicator Light
flashes BLUE. WINBOT 9 will not clean
until the Back-Up Battery is charged.
Please ensure there is a 15cm (5.9”) clearance between the glass and obstacles in the room
like curtains or furniture.
WINBOT 9 can clean horizontally mounted glass, or glass mounted at an angle, using the
Direction Control Buttons on the Remote Control.
Do not use WINBOT 9 upside down.
Do not use WINBOT9 on windows with an uneven surface, such as decaled, frosted, textured,
patterned, or coated glass.
WINBOT 9 should only be used with WINBOT Cleaning Solution. Using other cleaners significantly
reduces WINBOT’s performance and can damage the robot.
6
EN
3. Operating the Robot
3.2 Attach the Cleaning Pad
3.3 Assemble the Power Adapter
Turn WINBOT 9 over and attach the
Cleaning Pad to the Velcro smoothly. Make
sure the Cleaning Pad is placed exactly
within its Velcro area.
3.4 Install the Safety Tether
If WINBOT 9 is used to clean an outside window, the Safety Pod and
Tether MUST be used.
* If WINBOT 9 is being used to clean an inside window, please skip to step 3.6.
A
B
C
End A: Robot Power Cord
End C: Safety Pod
D
D
End B: Power Adapter Power Cord
End D: Safety Tether
EN
7
3. Operating the Robot
1
Loop one end of the Safety Tether to End
A on the Robot Power Cord and tighten.
2
Connect End A and End B and tighten.
3
Loop the other end of the Safety Tether
around the Safety Pod’s channel and pull
it tight.
* If the length of power cord restricts WINBOT 9’s movement, a WINBOT Extension Cord can
be used. Disconnect End A and End B, and connect them with both ends of the Extension
Cord respectively and tighten.
* Only one Extension Cord can be used when WINBOT 9 is cleaning an outside window.
8
EN
3. Operating the Robot
3.5 Place the Safety Pod
The Safety Pod MUST be placed
on the inside of the window.
Press the Safety Pod FIRMLY on the
inside of the window being cleaned.
Make sure the Safety Pod is attached
securely in place.
3.6 Spray Cleaning Solution
* WINBOT 9 should only be used with WINBOT Cleaning Solution. Using other cleaners
significantly reduces WINBOT’s performance and can damage the robot.
Spray each side of the Cleaning Pad with the
provided WINBOT Cleaning Solution 3 times.
The Cleaning Pad should be damp, not wet.
After spraying, wipe the bottom of WINBOT 9
with the provided Finishing Cloth.
EN
9
3. Operating the Robot
3.7 Start
1 Plug in WINBOT 9
2 Power ON
Move the Bottom Power Switch to the “ ”
position. WINBOT 9 is powered ON when it
beeps and the Status Indicator Light flashes
BLUE.
3 Place on the Glass
Press the START/PAUSE Button on
WINBOT 9’s Handle. WINBOT 9’s
suction motor starts.
Place WINBOT 9 on the window at least
10cm (4’’) from the corners or other
obstacles and press it firmly on the
window. WINBOT 9 has successfully
attached to the window when the Status
Indicator Light glows a continuous BLUE.
* Please ensure there is a 15cm (5.9”)
clearance between the glass and
obstacles in the room like curtains or
furniture.
10
EN
/4”
3. Operating the Robot
4 Start
Press the START/PAUSE Button on
WINBOT 9 or on the Remote Control to
begin cleaning.
3.8 Pause
Pause WINBOT 9 during cleaning by
pressing the START/PAUSE button on the
robot or on the Remote control.
WINBOT 9 can be directed to move forward,
backward, left and right using the Direction
Control Buttons on the Remote Control
when Paused. WINBOT 9 will clean when
Direction Control Buttons are used.
EN
11
3. Operating the Robot
3.9 Stop
When WINBOT 9 completes its cleaning cycle, it returns to the place it started and beeps.
1 Remove WINBOT 9
Grasp WINBOT 9’s Handle. Pull the Air
Release Trigger and remove WINBOT 9 from
the window. Polish away any marks left on
the glass from WINBOT 9’s removal with the
provided Finishing Cloth.
3 Remove the Safety Pod, if used.
2 Power OFF
Move the Power Switch to the “O” position.
4 Unplug WINBOT 9
* If WINBOT 9 has a problem and the Indicator Light glows RED, it can be reset by pressing
the Reset Button on the Remote Control.
12
EN
4. Maintenance
Before performing cleaning and maintenance on WINBOT 9, move the Bottom Power Switch
to the “O” position and unplug it from the receptacle.
4.1 Cleaning Pad
Turn the robot over and remove the Cleaning
Pad. Rinse the Cleaning Pad and allow it to dry
completely before re-attaching it to the robot.
* Do NOT use a wet Cleaning Pad
on WINBOT 9, or it may slip on the
window.
4.2 Cupule, Sensors, Squeegee, Corners
Cupule
Wheel Sensor
Turn the robot over and wipe any debris from
the surface of the Cupule with the provided
Finishing Cloth to maintain suction.
Turn the robot over and wipe the Wheel
Sensor with the provided Finishing Cloth
to maintain its effectiveness.
Edge Detection Sensors
Squeegee
Turn the robot over and wipe the four Edge
Detection Sensors clean with the provided
Finishing Cloth to maintain their effectiveness.
Turn the robot over and wipe the Squeegee
clean with the provided Finishing Cloth
to maintain its effectiveness.
EN
13
4. Maintenance
Cleaning WINBOT 9’s corners
Turn the robot over, remove the Cleaning
Pad and wipe the four corners of WINBOT 9
with the provided Finishing Cloth.
4.3 Driving Treads
Move the Bottom Power Switch to the “ ”
position.
14
EN
Inspect the Driving Treads by using the and
buttons on the Remote Control. Stop the
Driving Treads if dirt is seen on the Treads.
Move the Bottom Power Switch to the “O”
position.
Clean any dirt on the Driving Treads with the
provided Finishing Cloth.
5. Status Indicator Light and Sounds
Indicator
Description
Status Indicator Light flashes
GREEN
Back-Up Battery is low and is charging. WINBOT 9 will not clean
until the Back-Up Battery is properly charged.
Status Indicator Light flashes
BLUE
WINBOT 9 is powered ON, suction motor is running, and is ready
to be placed on the window.
If WINBOT 9 is already on the window, please refer to section 6
Troubleshooting.
Status Indicator Light glows
a continuous BLUE
WINBOT 9 has successfully attached itself to the glass and is
ready to clean.
Status Indicator Light glows
RED
WINBOT 9 has a problem. Please refer to Section 6,
Troubleshooting, for details.
WINBOT emit beeps
WINBOT 9 beeps in following situations:
WINBOT 9 is powered ON.
WINBOT 9 finishes cleaning.
WINBOT 9 is successfully paired with its Remote Control.
WINBOT 9 has a problem.
EN
15
6. Troubleshooting
NO. Malfunction
1
2
16
EN
Remote
Control
does not
work.
Status
Indicator
Light
flashes
BLUE after
WINBOT 9
is placed on
the glass.
Possible Causes
Solutions
WINBOT 9 is cleaning.
When WINBOT 9 is
cleaning, only the START/
PAUSE Button works on the
Remote Control.
Pause WINBOT 9 by pressing the START/
PAUSE button on the robot or Remote
Control. Other buttons on the Remote Control
will function when WINBOT 9 is paused.
The Remote Control is not
paired with WINBOT 9.
WINBOT 9 arrives from
the factory paired with
its Remote Control. If the
Remote Control becomes
un-paired or is replaced, it
can be re-paired.
Power ON WINBOT 9. At the same time,
press and hold
button on WINBOT 9
and
button on the Remote Control. Paring
is complete when WINBOT 9 beeps.
The batteries are not
installed in the Remote
Control or need to be
changed.
Install or replace the batteries in the Remote
Control.
There is not enough suction
to attach WINBOT 9 to the
glass.
A.Press WINBOT 9 on the window a little
more firmly.
B.Check for debris on the Cupule. Clean
the surface of the Cupule with the provided
Finishing Cloth as described in section 4.
C.The glass is too dirty for WINBOT 9 to
attach to the glass properly. Clean a small
area on the glass before use and place
WINBOT 9 there.
D.If the problem persists, please contact
Customer Service.
6. Troubleshooting
NO. Malfunction
Possible Causes
Interruption of electricity
while WINBOT 9 was
cleaning due to power
failure, plug displacement,
or loose connection to the
Power Adapter.
Status Light
Indicator
glows RED
3 after it is
powered ON, WINBOT 9 has encountered
a problem.
or during
cleaning.
4
WINBOT 9
does not
follow its
normal
cleaning
pattern,
moves
erratically or
stops.
Solutions
A. Connect WINBOT 9 to the Power Adapter
and plug into the receptacle. Press START/
PAUSE Button on the robot or on the Remote
Control. WINBOT 9 will resume cleaning.
B. In case of power failure, and the above
solution does not work, WINBOT 9 should
automatically go back to a place near its start
point. In rare cases when the robot does not go
back to a place near its start point, please use
the Direction Control Buttons on the Remote
Control to direct the robot to a position on the
window where you can safely reach it. Remove
the robot from the window and move the Bottom
Power Switch to the OFF position. If power
has resumed, move the Bottom Power Switch
back to the ON position, place the robot on the
window again and restart.
A. Press the RESET Button on the Remote
Control.
B. Check for stubborn stains on the window.
Clean the stains before using WINBOT 9.
C. Check the Cupule for dirt or damage. Clean
the Cupule as described in section 4. If Cupule
is scratched or damaged, replace it with a new
one.
D. If the problem persists, please contact
Customer Service.
The Cleaning Pad Plate
turned before WINBOT 9
reached the edge of the
window.
Spray additional Cleaning Solution on the
Cleaning Pad. Restart. If the problem persists,
call Customer Service.
Edge Detection Sensor
malfunction.
Clean the four Edge Detection Sensors as
described in Section 4. If the problem persists,
please contact Customer Service.
The window has a thick
layer of dirt on it.
Clean the window by hand first and use
WINBOT 9 for regular cleaning after that.
*WINBOT 9 is intended to be used for
maintenance cleaning on common windows.
The product is NOT designed to replace heavy
duty or first time cleaning.
The Cleaning Pad is not
placed exactly within its
Velcro area.
Remove and reattach the Cleaning Pad making
sure it is placed exactly within its Velcro area.
The Cleaning Pad is dirty.
Replace the Cleaning Pad.
The Cupule is dirty or the
Driving Treads are dirty.
Clean the surface of the Cupule and Driving
Treads with the provided Finishing Cloth as
described in section 4. If the problem persists,
please contact Customer Service.
EN
17
WINBOT 9S-000-IM2014R01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising