1W AC-DC Power-Supply PAC1B - HY-LINE

1W AC-DC Power-Supply PAC1B - HY-LINE
1W AC-DC Power-Supply PAC1B
●
●
●
●
●
85 … 264 VAC universal input range
Continuously short circuit and over current protected
Isolation class II
MTBF > 300000 h
Small outlines
Model guide
Type
PAC1B05S
PAC1B09S
PAC1B12S
PAC1B15S
PAC1B24S
Output voltage
Accuracy
[VDC]
[%] max.
5.0
±5
9.0
±5
12
±5
15
±5
24
±5
Output current
[mA] max.
200
111
83
67
42
Ripple & noise up
to 20 MHz
[mVp-p] max.
120
120
120
120
120
Efficiency typ.@ full
load, Vin 230 VAC
[%]
66
67
70
69
68
Capacitive load
[µF]
200
100
100
100
100
Specifications
Input
Voltage range
Frequency
Full load input current
Inrush current
Standby power
Recommended fuse
Hold up time
Isolation
Isolation voltage (input to output)
Isolation resistance
Output
Minimum load
Line regulation
Load regulation @ 5 to
100% load change
Temperature coefficient
85..264 VAC or
70..400 VDC
Power derating see diagram
47…440 Hz
120 mA max @ 115 VAC
40 mA max @ 230 VAC
10 A @ 115 VAC
20 A @ 230 VAC
0.5 W, max.
1 A / 250 V slow blow
80 ms @ 115 VAC
300 ms @ 230 VAC
3000 VAC for 1 minute
100 MΩ
5%
±1.5 %, typ.
±2.5 %, typ.
0.1 % / °C
Conducted emission
EMI
Radiation emission
ESD Electrostatic discharge
RS field susceptibility
EMC
EFT Fast transients on mains line
EMS
Surge
CS
PFM
Voltage dips,
short and interruptions immunity
Protection
Short circuit
Over temperature
General
Reliability MTBF@25°C
Switching frequency
Environmental
Operating temperature
(ambient)
Power derating
Storage temperature
Case temperature
Humidity
Cooling
Safety approvals
Physical
Dimensions
Weight
Case material
Mounting
Soldering temperature, Time
Continuous, auto recovery
No
>300000 h
~ 50 kHz
-40 °C to +85 °C
(with derating, see diagram)
see diagram
-40 °C to +105 °C
90 °C, max.
85 %, max.
Free-air convection
EN60950, UL60950
35.0 x 27.0 x 11 mm
8g
UL94V-0
On PCB
Wave 265 °C max., 10 s max.
Manual 370 °C max., 5 s max.
EN55022 (CISPR22), class A (External circuit refer to fig. 2)
EN55022 (CISPR22), class B (External circuit refer to fig. 3)
EN55022 (CISPR22), class A (External circuit refer to fig. 2)
EN55022 (CISPR22), class B (External circuit refer to fig. 3)
IEC, EN61000-4-2 contact ± 4 kV perf. criteria B
IEC, EN61000-4-3, 10 V/m perf. criteria A (External circuit refer to fig. 3)
IEC, EN61000-4-4, ± 2 kV, perf. criteria B (External circuit refer to fig. 2)
IEC, EN61000-4-4, ± 4 kV, perf. criteria B (External circuit refer to fig. 3)
IEC, EN61000-4-5, ± 1 kV perf. criteria B (External circuit refer to fig. 3)
IEC, EN61000-4-5, ± 2 kV perf. criteria B (External circuit refer to fig. 3)
IEC, EN61000-4-6, 3 V rms perf. criteria A (External circuit refer to fig. 3)
IEC, EN61000-4-8, 10 A/m perf. criteria A
IEC, EN61000-4-11, 0…70 % perf. criteria B
1. External electrolytic capacitor are required to models. More details refer to typical applications.
2. Ripple and noise were measured refer to “ripple and noise measure figure”.
3. All specifications were measured at Ta 25 °C, humidity <75 %, nominal input voltage (115 VAC or 230 VAC) and rated output load
unless otherwise specified.
4. In this datasheet, all the test methods of indications are based on corporate standards.
5. Module required dispensing fixed after assembled.
Page 1 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: power@hy-line.de
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: power@hy-line.ch
1W AC-DC Power-Supply PAC1B
Functional diagram
Vin (N)
Vin (L)
1
Input
rectifier
3
12
+ Vout
Output
rectifier &
filter
DC/DCConverter
10
- Vout
5
C1
External
capacitor
7
Application note inadmissible connection
PAC1BxxS
L
+Vout
-Vout
N
PE
This connection is not supported for the PAC1B series!
Ripple and noise measure configuration
PAC1BxxS
F1
L
C2
L1
C3
C4
Load
12
+Vo
3
Measure points for
oscilloscope probe
-Vo
10
N
1
7 C1
5
CY
Figure 2 EMC application circuit for standard requirement
L
N
F1
NTC
L2
PAC1BxxS
C2
L1
C3
D1
C4 +Vout
-Vout
U
MOV1
C1
CY
For standard EMC requirement, please refer to figure 2, recommended parameters are shown in this table.
Type
F1
MOV1
NTC
L1
L2
CY
C1
C2
C3
PAC1B05S
150
µF
1A
PAC1B09S
250V
Type
Type
2.2
10 µF
68 µF
1 nF
1 mH
PAC1B12S
slow S14K350
5D-9
µH
35 V
400 VAC 400 V
100 µF
PAC1B15S
blow
PAC1B24S
C4
0.1 µF
50 V
ceramic
D1
SMBJ7.0A
SMBJ12A
SMBJ20A
SMBJ30A
Page 2 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: power@hy-line.de
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: power@hy-line.ch
1W AC-DC Power-Supply PAC1B
Recommend PCB layout
Linewidth ≥3 mm, line to line distance ≥6 mm, line- ground distance ≥6mm, undefined unit: mm
Figure 3, EMC application circuit for applications with higher EMC requirement
Complete input filter module PN: PIF003A
PAC1BxxS
L F1
L
LDM
C2
CY
MOV2
U
CX
L1
C3 D1 C4 +Vout
+
Rd
-Vout
CY
N
N
LCM
PE
C1
CY
For higher EMC requirement, please refer to figure 3, recommended parameters are shown in this table.
Type
F1
Filter module
CY
C1
C2
C3
PAC1B05S
150 µF
PAC1B09S
1A 250V
68 µF, 35 V
PIF003A
1 nF, 400 VAC 10 µF, 400 V
PAC1B12S
slow blow
100 µF
PAC1B15S
PAC1B24S
C4
0.1 µF
50 V
ceramic
D1
SMBJ7.0A
SMBJ12A
SMBJ20A
SMBJ30A
Note:
C1 and C3 are electrolytic capacitors. They are required both AC input and DC input. When AC input, C1 is used as filter
capacitor, the value of C1 is recommended to be 10 μF / 400 V. When DC input, C1 is used as EMC filter capacitor, the value
of C1 is recommended to be 10 μF / 400 V (when the input voltage is above 370 VDC, the recommended value of C1 is 10 μF /
450 V). C2 and C3 are output filter capacitors, they are recommended to be high frequency and low impedance electrolytic
capacitors. Capacitance and rated ripple current of capacitors refer to the data sheets provided by the manufactures. Voltage
derating of capacitors should be 80 % or above. C4 is a ceramic capacitor, which is used to filter high frequency noise. C2, C3
and L1 form a pi-type filter circuit. Current of L1 and L2 refer to the datas heets provided by the manufactures, current derating
should be 80% or above. TVS is a recommended component to protect post-circuits (if converter fails). External input NTC is
recommended to use 5D-9. External input MOV1 is recommended to use S14K350.
Page 3 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: power@hy-line.de
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: power@hy-line.ch
1W AC-DC Power-Supply PAC1B
Page 4 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: power@hy-line.de
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: power@hy-line.ch
1W AC-DC Power-Supply PAC1B
Dimensions
Pin connections
Pin
Function
1
AC In (N) or -Vin
3
AC In (L) or +Vin
5
+ Capacitor (C1)
7
- Capacitor (C1)
10
- DC Out
12
+ DC Out
PHI-CON is a trademark of HY-LINE Power Components.
Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for
use carefully before using!
Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the
express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose
failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected
to result in significant injury to the user. Rev: 03.14 f
Page 5 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: power@hy-line.de
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: power@hy-line.ch
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising