C20-DN Series 650 TV lines

C20-DN Series 650 TV lines
C20-DN Series 650 TV lines
High Resolution Camera
Installation/Operation Manual
C3901M-EN (02/12)
Before attempting to connect or operate this product, please read these instructions
carefully and save this manual for future use.
1
CONTENTS
Important Safety Instructions ........................................................................................................................ 3
Troubleshooting Tips ..................................................................................................................................... 4
Regulatory Notices ........................................................................................................................................ 5
1. Introduction................................................................................................................................................ 6
2. Part Names and Locations ........................................................................................................................ 7
3. OSD Menu ............................................................................................................................................... 10
4. OSD Menu Settings ................................................................................................................................ 11
4.1 LENS .............................................................................................................................................. 12
4.2 SHUTTER/AGC ............................................................................................................................. 12
4.3 WHITE BAL .................................................................................................................................... 13
4.4 BACKLIGHT ................................................................................................................................... 14
4.5 PICTURE ADJUST ........................................................................................................................ 14
4.6 ATR* ............................................................................................................................................... 14
4.7 MOTION DET................................................................................................................................. 14
4.8 PRIVACY ....................................................................................................................................... 15
4.9 DAY/NIGHT.................................................................................................................................... 15
4.10 NR ................................................................................................................................................ 15
4.11 CAMERA ID ................................................................................................................................. 16
4.12 SYNC ........................................................................................................................................... 16
4.13 LANGUAGE ................................................................................................................................. 16
4.14 CAMERA RESET......................................................................................................................... 16
4.15 SAVE ALL .................................................................................................................................... 16
5. Specification ............................................................................................................................................ 17
PRODUCT WARRANTY AND RETURN INFORMATION ......................................................................... 18
2
C3901M-EN(02/12)
Important Safeguards and Warnings
Important Safeguards and Warning
IMPORTANT
SAFETY INSTRUCTIONS
Important Safety
Instructions
1.
Read Instructions. All the safety and operating instructions should be read before the camera is
operated.
2.
Retain Instructions. The safety and operating instructions should be retained for future reference.
3.
Heed Warnings. All warnings on the camera and in the operating instructions should be adhered
to.
4.
Follow Instructions. All operating and use instructions should be followed.
5.
Cleaning: Unplug the power unit from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
6.
Attachments: Do not use attachments not recommended by your appliance dealer, as they may
cause hazards.
7.
Water and Moisture: Do not use the camera in any location in which it may be exposed to water
or moisture. (For example, dripping, splashing, or liquid near equipment etc.)
8.
Accessories: Do not place the camera on an unstable cart, stand, tripod,
bracket, or table. The camera may fall, causing serious injury to a child or adult,
and serious damage to the camera. Use only with mounting accessories
recommended by your appliance dealer or sold with the camera. Any mounting
of the camera should follow your appliance dealer's instructions.
The camera must be installed in a location or on a piece of equipment that can
withstand three times the total weight of the camera, including the lens, camera,
mount, adapter, etc.
9.
Any appliance and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and cart combination to overturn.
10. Ventilation: The camera should never be placed near or over a radiator or heat register. The
camera should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or your appliance dealer's instructions have been adhered to.
11. Power Sources: The camera should be operated only from the type of power source indicated
on the rating plate. If you are not sure of the type of power supply for your installation site,
consult your appliance dealer or local power company.
12. Power Cord Protection: Power supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit from the camera.
13. Lightning: For added protection for the camera during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the
cable system. This will prevent damage to the camera due to lightning and power line surges.
14. Overloading: Do not overload the wall outlet and extension cord, as this can result in a risk of fire
or electric shock.
15. Object and Liquid Entry: Never push objects of any kind into the camera through openings, as
they may touch dangerous voltage points or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the camera.
3
C3901M-EN(02/12)
16.
Important Safeguards and Warnings
Important Safeguards and Warning
Servicing:IMPORTANT
Do not attempt to service
the camera yourself,
as opening or removing covers may
SAFETY
INSTRUCTIONS
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
17. Damage Requiring Service: Unplug the power unit from the wall outlet. Refer servicing to
qualified service personnel under the following conditions.
a.
When the power supply cord or plug is damaged.
b.
If liquid has been spilled or objects have fallen into the camera.
c.
If the camera has been exposed to rain or water.
d.
If the camera does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions, as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to restore the camera to its normal operation.
e.
If the camera has been dropped or the cabinet has been damaged.
f.
When the camera exhibits a distinct change in performance. This indicates a need for
service.
18. Replacement Parts: When replacement parts are required, be sure the service technician has
used replacement parts specified by a qualified dealer or that have the same characteristics as
the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
19. Safety Check: Upon completion of any service or repairs to the camera, ask the service
technician to perform safety checks to determine that the camera is in proper operating condition.
Troubleshooting Tips
 Ensure that all power cords are attached.
 Ensure that all power switches are in the ON position.
 Ensure that all cables are installed in the proper location and are fully seated.
4
C3901M-EN(02/12)
Important Safeguards and Warnings
Important Safeguards and Warning
IMPORTANT SAFETY INSTRUCTIONS
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Changes and Modifications not expressly approved by the manufacturer or registrant of this
equipment can void your authority to operate this equipment under Federal Communications
Commission’s rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this
equipment. Operation with non-approved -equipment or unshielded cables is likely to result in
interference to radio and television reception.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Operating Notes:
 For dual voltage model: Connect to DC12V or AC 24V power adapter.
 For high voltage model: Connect to AC 220V power source.
Operating Conditions
• Avoid viewing very bright objects (example, light fixtures) for extended periods.
•
Avoid operating or storing the unit in the following locations:
- Extremely humid, dusty, hot/cold environments (where the operating temperature is outside
the recommended range of 14°F to 122°F [-10°C to +50°C])
- Close to sources of powerful radio or TV transmitters
- Close to fluorescent lamps or objects reflecting light
- Under unstable light sources (may cause flickering)
5
C3901M-EN(02/12)
1. Introduction
Introduction
INTRODUCTION
The box camera is ideal for indoor installation in commercial environment.
Before You Begin:
Please read this guide carefully before you install the box camera. Keep this guide for future reference.
Package Contents:
Check that the items received match those listed on the order form and packing slip. The box camera
packing box includes:
•
One installation/operation manual
•
One fully assembled camera
•
One Lens mounting cap
•
One Hexagonal and Minus wrench
•
One C adapter ring
•
One Auto Iris lens connector
If any parts are missing or damaged, contact the dealer you purchased the camera.
Optional Accessories:
•
C10-UM Mount
It is recommended mounting camera with C10-UM mount, a C10 series universal wall/ceiling/rail
mounting kit.
6
C3901M-EN(02/12)
Part Names and Locations
OSD Setup Menu
2. Part Names and Locations
Figure 2-1 C20-DN-6/C20-DN-6X
7
C3901M-EN(02/12)
Part Names and Locations
OSD Setup Menu
Figure 2-2 C20-DN-7X
8
C3901M-EN(02/12)
Part Names and Locations
OSD Setup Menu
(1) Lens mount C/CS
For the installation of CS Mount lenses only, use
no adapter.
Before mounting the C mount lens, you can
screw the C adapter onto the lens, and then
screw the lens onto the lens mount.
(2) Back Focus adjustment
A. Back Focus Screw:
Using Minus wrench to loosen this screw before
you use the Focus Adjustment. To maintain the
correct focus afterwards, ensure that it is
tightened.
B. Focus Adjustment:
Adjust this dial to obtain correct back-focus
whilst using a CS mount lens.
(3) Video Output Terminal
BNC: Used to give out the video signal.
Connected to the video input terminal of a
monitor, Matrix, etc. (to be terminated with 75
ohm impedance)
(4) OSD joystick control
Press the OSD joystick control straight down:
• For two seconds to enter the Main menu.
• To enter a screen or to select a submenu
option. A selected menu item blinks.
(5) I/O
Connect your external devices to the
corresponding I/O terminal block. The pins of the
I/O terminal block controls the following signals:
TP+/-: UTP (Unshielded Twisted Pair)
(6) Power Connector
Connect to the respective power source.
• For dual-voltage model: Connect to DC12V or
AC 24V power adapter.
• For high-voltage model: Connect to AC 220V
power source.
WARNING:
This apparatus must be GROUNDED.
(7) Power Indicator
The power indicator light is lit (Red), which
means the power is connected.
(8) Auto Iris lens connector
Supplies power and control signals to an
auto-iris lens.
9
C3901M-EN(02/12)
OSD Setup Menu
OSD Setup Menu
3. OSD Menu
Set up menu
Default set
Menu
Lens
AUTO
AUTO/Manual
Shutter/AGC
AUTO
AUTO (High Luminance, Low Luminance)/ Manual (Mode,
Shutter, AGC)
WHITE BAL
Backlight
Pic Adjust
ATR
Motion Det
ATW
OFF
Option
OFF
OFF
ATW/Push Lock/User1/User2/Anti CR/Manual
OFF/BLC/HLC
Mirror, Brightness, Contrast, Sharpness, Hue, Gain
OFF/ON (Luminance, Contrast)
OFF/ON (Detect Sense, Block DISP, Motion Area, Area Sel)
Privacy
OFF
OFF/ON (Area Sel, Color, Transp, Mosaic)
Day/Night
AUTO
AUTO/BW/Color
NR
OFF
NR Mode (Off, Y, C)
Y Level
C Level
Camera ID
SYNC
OFF
INT
OFF/ON
INT
Language
English
ENGLISH / SPANISH / RUSSIAN / GERMAN / FRENCH /
JAPANESE or PORTUGUESE
Camera Reset
Exit
Save All
10
C3901M-EN(02/12)
Menu Settings
4. OSD Menu Settings
Entering OSD Menu
Hold down on the joystick to open the Main menu. Use the UP/DOWN functions of the joystick to move
the cursor to the item you want to modify. A selected menu item will be highlighted.
Press UP: Press to move the cursor up.
Press Down: Press to move the cursor down.
Enter button: Hold down on the joystick to enter the selected item or change the settings of the
selected item.
Press Right: Press it to change the settings of the selected item.
Press Left: Press it to change the settings of the selected item.
NOTE: When an item is selected, it will be highlighted.
After all the settings have been satisfied, move the cursor to the "Save All" item and press the enter
button. Then move the cursor to the "EXIT" item and press the enter button to exit OSD setup menu.
You can also restore the settings to factory default by moving the cursor to the "CAMERA RESET" item
and then pressing the Enter button. Then move the cursor to the "Save All" item and press the Enter
button.
11
C3901M-EN(02/12)
Menu Settings
Use the OSD menu to set up the camera for optimum performance.
LENS
SHUTTER/AGC
WHITE BAL
PICT ADJUST
ATR
MOTION DET
NEXT
EXIT
AUTO
AUTO
ATW
OFF
OFF
SAVE ALL
PRIVACY
OFF
DAY/NIGHT
AUTO
NR
CAMERA ID
OFF
SYNC
INT
LANGUAGE
ENGLISH
CAMERA RESET
BACK
EXIT
SAVE ALL
4.1 LENS
Select Auto or Manual lens function. The default setting is AUTO (Auto Iris lens). Move the joystick
control LEFT or RIGHT to select Auto or Manual Lens. Enter the AUTO submenu as shown in the figure.
Move the joystick control UP or DOWN to open, close, or set IRIS to auto mode. Move the joystick
control UP or DOWN to adjust the DC Iris Lens convergence speed.
If speed value is less, the IRIS will be become more slower. If speed value is higher, the IRIS will be
become more faster.
TYPE
MODE
SPEED
RETURN
DC
OPEN
046
4.2 SHUTTER/AGC
Set Shutter speed/AGC (Auto Gain Control) function. The default setting is AUTO. Move the joystick
control LEFT or RIGHT to select AUTO or MANUAL.
SUGGESTED USE:
DC Lens: When using DC lens, it is recommended to set SHUTTER/AGC to AUTO mode. Enter the
AUTO submenu as shown in the figure. Move the joystick control UP or DOWN to adjust HIGH
LUMINANCE MODE to AUTO IRIS.
Manual Lens: When using MANUAL lens, it is recommended to set SHUTTER/AGC to AUTO mode.
Enter the AUTO submenu as shown in the figure. Move the joystick control UP or DOWN to adjust HIGH
LUMINANCE MODE and LOW LUMINANCE setting.
12
C3901M-EN(02/12)
Menu Settings
AUTO IRIS and SHUT+AUTO IRIS difference
• Use DC lens and setting to AUTO IRIS mode for normal condition application environments. The IRIS
level will be controlled by camera brightness.
• Use DC lens and setting to SHUT+AUTO IRIS mode for high light application environments. The
exposure will be controlled by AES or the DC Iris. The iris level will be controlled by camera brightness.
HIGH LUMINANCE
MODE
BRIGHTNESS
LOW LUMINANCE
MODE
BRIGHTNESS
RETURN
AUTO IRIS
024
AGC
x 0.25
The shutter speed is variable from 1/50(1/60) sec to the 1/10Ksec and the AGC is selectable depending
on your environment condition.
MODE
SHUTTER
AGC
RETURN
OFF
1/50(1/60)
6.0
Note:Menu settings for Lens and Shutter/AGC
• When the camera first starts up the menu setting for Lens=Auto (Mode=Auto) and the settings for
Shutter/AGC= High Luminance=Auto Iris
• When you change Lens=Manual then the default settings for Shutter/AGC= High Luminance=Shut
• When you change Lens=Auto then the settings for Shutter/AGC=Shut+AutoIris (this is not the default
value of menu setting when first turned on)
4.3 WHITE BAL
WHITE BALANCE controls color on the screen. The default is ATW. The color temperature range is
2500°K~ 9500°K. Move the joystick control LEFT or RIGHT to select ATW (Auto White Balance), PUSH,
PUSH LOCK, USER1, USER2, Anti CR (Anti Color Rolling Suppression) or MANUAL mode. Enter the
ATW submenu as shown in the figure. Move the joystick control UP or DOWN to select the desired
value. ATW (Auto White Balance) select when the scene illumination varies between indoor scenes and
outdoor scene lighting.
NOTE:
When setting different value of ATW FRAME and application environment, the color temperature range
of white balance will be changed. The color temperature range of x0.50 of ATW FRAME will be smaller
than x2.00.
SPEED
DELAY CNT
ATW FRAME
ENVIRONMENT
RETURN
171
152
x 0.50
INDOOR
If selected MANUAL mode, you can adjust LEVEL from 17 to 54.
If selected USER1 or USER2 mode, you can adjust B-GAIN and R-GAIN value from 0 to 255.
If selected PUSH mode in the appropriate position, whole area will perform white balance.
If selected PUSH LOCK mode in the appropriate position, WHITE BALANCE will perform once.
If selected Anti CR mode in the appropriate position, whole area will effectively restrain color cast.
13
C3901M-EN(02/12)
Menu Settings
4.4 BACKLIGHT
Set Backlight compensation function. The default is OFF. Move the joystick control LEFT or RIGHT to
select OFF, BLC or HLC (Highlight Compensation) mode. When you switched BLC, the function
controls the light level to overcome severe backlighting conditions. HLC activated automatically
depending on the shooting condition (detects night and high-luminance)
BLC and HLC Compensation are the functions that achieve the brightness of a selected area to an
optimum image level. Due to the intense light coming from the back of objects in the area expected to
view, the auto iris lens tends to close and areas desired to see become dark and invisible.
4.5 PICTURE ADJUST
Set PICTURE ADJUST function. Enter PICT ADJUST submenu as shown in the figure. Move the
joystick control UP or DOWN to set picture Brightness, Contrast, Sharpness, Hue, or Gain value. In
addition, you can set MIRROR to the ON mode then the picture to be left or right.
MIRROR
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
GAIN
RETURN
OFF
000
128
128
128
128
4.6 ATR*
Set ATR (Adaptive Tone-curve Reproduction) function. The default is OFF. Move the joystick control
LEFT or RIGHT to select the ON mode then enter to the ATR submenu, you can set LUMINACE and
CONTRAST to optimize by image.
LUMINANCE
CONTRAST
RETURN
LOW
LOW
*Also known as Wide Dynamic Range. This function expands the video dynamic range of the camera
and improves visibility of images even in high contrast environments.
4.7 MOTION DET
Set Motion Detection function. MOTION DET allows detecting moving objects on the screen. The default
is OFF. Move the joystick control LEFT or RIGHT to select the ON mode then enter to the MOTION DET
submenu. You can set 4 motion areas to detect moving objectives and adjusts the motion detection
sensitivity. Use the LEFT/RIGHT functions of the joystick control to set the sensitivity from 000 to 127.
DETECT SENSE
BLOCK DISP
MONITOR AREA
AREA SEL
TOP
BOTTOM
LEFT
RIGHT
RETURN
100
OFF
OFF
1/4
000
000
000
000
14
C3901M-EN(02/12)
Menu Settings
4.8 PRIVACY
Set PRIVACY function. The default setting is OFF. Move the joystick control LEFT or RIGHT to select
the ON mode then enter to the PRIVACY submenu. You can configure 8 privacy positions, set 8 privacy
areas, choose different color zone and set transparency of 8 privacy zone. However if you enable
MOTION DET function, then PRIVACY function will be supported 4 zones only. In addition, the image
of PRIVACY can allow you to set MOSAIC function.
REA SEL
TOP
BOTTOM
LEFT
RIGHT
COLOR
TRANSP
MOSAIC
RETURN
1/8
000
000
000
000
1
0.00
OFF
4.9 DAY/NIGHT
Set DAY/NIGHT function. The default setting is AUTO. Move the joystick control LEFT or RIGHT to
select the AUTO, COLOR, BW mode. Enter the AUTO submenu as shown in the figure. Move the
joystick control UP or DOWN to adjust BURST value and set the time before the camera switches to
DAY-> NIGHT mode or NIGHT->DAY mode.
When select Day->NIGHT level to set up switchover point of brightness from COLOR mode to B/W mode
under different Lux levels.
When select NIGHT->DAY level to set up switchover point of brightness from B/W mode to COLOR
mode under different Lux levels.
BURST
DELAY CNT
DAY->NIGHT
NIGHT->DAY
RETURN
OFF
100
100
100
If selected COLOR mode, you can force the camera to stay in DAY (COLOR) mode.
If selected BW mode, you can force the camera to stay in BW (NIGHT) mode. The BW submenu allows
you to select BURST to be ON or OFF.
4.10 NR
You can configure the 2D DNR (Digital Noise Reduction) settings and reduce noise on the screen. Enter
NR submenu as shown in the figure. Move the joystick control UP or DOWN to set NR MODE. When
you enable the NR MODE to the Y (BRIGHT) / C (COLOR), C LEVEL or Y LEVEL mode, you can adjust
Y LEVEL or C LEVEL depending on your environment condition.
NR MODE
Y LEVEL
C LEVEL
RETURN
Y/C
000
000
Note: When the Y Level is higher the noise in dark areas becomes lessened. Also, resolution will
become lower. When it is lower, there are more noise in dark areas.
15
C3901M-EN(02/12)
Menu Settings
When the C Level is higher the noise in dark areas becomes lessened. Also, resolution will become
lower. When it is lower, there are more noise in dark areas.
In the dark environment, you can adjust the value higher of Y Level to reduce the dark noise; adjust the
value higher of C Level to reduce the color noise.
4.11 CAMERA ID
CAMERA ID displays ON or OFF. The default setting is OFF. You can set the ON mode to add a camera
title up to 26 characters with 2 lines and also select where the title appears on the monitor screen.
4.12 SYNC
The default setting is INT. This has no adjustment.
4.13 LANGUAGE
OSD supports 6 multi built in languages. The default setting is English. Move the joystick control LEFT or
RIGHT to select the ENGLISH / SPANISH / RUSSIAN / GERMAN / FRENCH / JAPANESE or
PORTUGUESE.
4.14 CAMERA RESET
Move to the CAMERA RESET mode then Press the ENTER key to recall factory settings.
4.15 SAVE ALL
Save all settings and exit.
16
C3901M-EN(02/12)
5. Specification
Camera System Type
Format
Optical System
Imager Size
In Cut Filter
IR
IR Sensitivity
Electric
Sync System
Lens Mount
Easy Back Focus Adjustment
Lens Drive
Horizontal Resolution
Sensitivity
S/N Ratio
Shutter
AGC
Easy Back Focus Adjustment
Color Correction
White Balance
BLC
WDR
Noise Reduction-DNR
Motion Detection
Privacy Zones
Camera ID
Connection/Termination
Set Up/OSD Input Device
Multi Language
Specification
SPECIFICATION
C20-DN-6
NTSC
C20-DN-6X
1/3"
Yes - D/N Switch (ICR)
850nm >40% Peak Response
Internal
CS
Yes
DC
650 TV lines
f/1.2; 2,850°K; 30IRE
f/1.2; 2,850°K; 30IRE
Color (17 ms) 0.13 Lux
Color (20 ms) 0.13 Lux
Mono (17 ms) 0.05 Lux
Mono (20 ms) 0.05 Lux
default 48dB
>52dB by parameter adjustment
Auto: 1/60~1/10,000
Auto: 1/50~1/10,000
Manual: 1/60~10,000
Manual: 1/50~10,000
Off/On 35dB
Yes
With White Balance
ATW/Push Lock/Manual/Anti CR/User2/User/Push
Off/ BLC/ HLC(High Light compensation) (selectable)
On / Off (selectable, ATR)
2D
Yes
Yes
Yes
Terminal Strip - Removable
Input Buttons/5 Way Rocker
English, Russian, German,
French, Spanish, Japanese
UTP
Power supply
Power
Power Consumption (Max)
Environment
Operating Temperature Range
Operating humidity
Mechanism
Construction
Dimension (L W H)
Weight(unit)
Power LED
C20-DN-7X
PAL
English, Russian, German,
French, Spanish, Portuguese
Yes
12VDC/24VAC, Autosensing +10/-15%
220VAC, +10/-15%
4W
5W
14°F (-10°C) Minimum,
122°F (50°C) Maximum
20~90% non-condensing
Diecast
60mm X55mm X108mm
300g
450g
Red-Rear Panel
17
C3901M-EN(02/12)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any
merchandise proved defective in material or
workmanship for a period of one year after the
date of shipment.
Exceptions to this warranty are as noted below:
•
•
•
Five years:
– Fiber optic products
– Unshielded Twisted Pair (UTP) transmission
products
– CC3701H-2, CC3701H-2X, CC3751H-2,
CC3651H-2X, MC3651H-2, and MC3651H2X camera models
Three years:
– FD Series and BU Series analog camera
models.
– Fixed network cameras and network dome
cameras with Sarix® technology
– Sarix thermal imaging products (TI and ESTI
Series)
– Fixed camera models (C20 Series,
CCC1390H Series, C10DN Series, C10CH
Series)
– EH1500 Series enclosures
®
– Spectra IV products (including Spectra IV
IP)
– Spectra HD dome products
®
– Camclosure IS Series integrated camera
systems
– DX Series video recorders (except DX9000
Series which is covered for a period of one
year), DVR5100 Series digital video
recorders, Digital Sentry® Series hardware
products, DVX Series digital video recorders,
and NVR300 Series network video
recorders
®
– Endura Series distributed network-based
video products
®
– Genex Series products (multiplexers,
server, and keyboard)
– PMCL200/300/400 Series LCD monitors
– PMCL5xxF Series and PMCL5xxNB Series
LCD monitors
Two years:
– Standard varifocal, fixed focal, and
motorized zoom lenses
– DF5/DF8 Series fixed dome products
®
– Legacy Series integrated positioning
systems
™
– Spectra III , Spectra Mini, Spectra Mini IP,
®
Esprit , ExSite®, ExSite IP, and PS20
scanners, including when used in
continuous motion applications
– Esprit Ti and TI2500 Series thermal imaging
products
– Esprit and WW5700 Series window wiper
(excluding wiper blades)
– CM6700/CM6800/CM9700 Series matrix
®
– Digital Light Processing (DLP ) displays
(except lamp and color wheel). The lamp
and color wheel will be covered for a period
of 90 days. The air filter is not covered
under warranty.
• Six months:
– All pan and tilts, scanners, or preset lenses
used in continuous motion applications
(preset scan, tour, and auto scan modes)
Pelco will warrant all replacement parts and
repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair
shall be sent freight prepaid to a Pelco
designated location. Repairs made necessary
by reason of misuse, alteration, normal wear, or
accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to
no liability for damages or loss resulting from the
specific use or application made of the Products.
Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of
any rights of any party or product liability,
relating to the Products shall not exceed the
price paid by the Dealer to Pelco for such
Products. In no event will Pelco be liable for any
special, incidental, or consequential damages
(including loss of use, loss of profit, and claims
of third parties) however caused, whether by the
negligence of Pelco or otherwise.
The above warranty provides the Dealer with
specific legal rights. The Dealer may also have
additional rights, which are subject to variation
from state to state.
If a warranty repair is required, the Dealer must
contact Pelco at (800) 289-9100 or (559) 2921981 to obtain a Repair Authorization number
(RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, sales order
number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a
product that does not fall under the warranty
conditions stated above, please include a
18
C3901M-EN(02/12)
PRODUCT WARRANTY AND RETURN INFORMATION
written explanation with the product when
returned.
Method of return shipment shall be the same or
equal to the method by which the item was
received by Pelco.
RETURNS
To expedite parts returned for repair or credit,
please call Pelco at (800) 289-9100 or (559)
292-1981 to obtain an authorization number (CA
number if returned for credit, and RA number if
returned for repair) and designated return
location.
All merchandise returned for credit may be
subject to a 20 percent restocking and
refurbishing charge.
Goods returned for repair or credit should be
clearly identified with the assigned CA or RA
number and freight should be prepaid.
This equipment contains electrical or electronic components that must be recycled
properly to comply with Directive 2002/96/EC of the European Union regarding the
disposal of waste electrical and electronic equipment (WEEE). Contact your local
dealer for procedures for recycling this equipment.
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates.
All other product names and services are the property of their respective companies.
Product specifications and availability are subject to change without notice.
© Copyright 2012, Pelco, Inc.
All rights reserved.
19
C3901M-EN(02/12)
www.pelco.com
Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising