Quick-Start Guide

Quick-Start Guide
Quick Start Guide
INSTEON® Keypad Dimmer Switch, 6 and
8-Button
Models: 2334-222, 2334-232
Primary
Load
Control
What’s Included?
•
•
KeypadLinc Dimmer (6 or 8-button)
Four wire nuts
Secondary
buttons
Tools Needed
•
•
Bladed #1 screwdriver
Philips screwdriver
•
•
Voltage meter
Wire cutter/stripper
Set button
Installing Keypad
Installation should only be performed by a qualified electrician or a homeowner who is familiar and comfortable with electrical
circuitry. If you have questions, consult an electrician or call the INSTEON Support Line at 866-243-8022
1)
Turn off breaker/fuse and verify that the power is off
2)
Unscrew existing switch, disconnect wires and prep all wires to be connected to Keypad, with 1/2” (12mm) of bare wire on
the ends
3)
Firmly connect wires per table/diagram and ensure no exposed wire.
Keypad Wire
Wall Box Wires
Ground - commonly bare, green wire
Bare Copper
or green screw
White
Neutral - commonly white
Red
Load - light, load, etc.
Black
4)
5)
Line - 100 – 277V (commonly black)
Place Keypad into wall box and turn on breaker/fuse
Connected load will turn on
Keypad On button will turn on
Test by tapping Keypad on/off buttons
Connected load will turn on and off
For 6-button, Keypad On button will turn on when on and Off button
will turn on when off
For 8-button, Keypad “Main On/Off” button will turn on and off
Using Keypad
•
•
•
Connected load will react just like the scene responders to on/off button taps
LED will mimic the on/off status of a dimmer whose scene level is 100% bright
Other buttons toggle by default
Button LED
Button Type
First Press and Hold
Subsequent Press and Holds
before Tap
Brighten scene until
Opposite of last press and hold
Toggle
Off
release
(e.g. if last was brighten, it will dim)
Opposite of last press and hold
Toggle
On
Dim scene until release
(e.g. if last was brighten, it will dim)
Always On
Either
Brighten scene until release
Always Off
Either
Dim scene until release
2334-222/2334-232 Rev. 6/19/2013 10:25 AM / See Owner’s Manual for Warranty Information.
Protected under U.S. and foreign patents (see www.insteon.com/patents)
© Copyright 2013 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022
Make Keypad a Controller
Use Keypad button to control other INSTEON devices.
1) Tap the Keypad button of choice (for 6-button, use ON button as main scene)
2) Press and hold Keypad set button until it beeps
Keypad button LED and the set button will start blinking green
3) Turn responder on (or any other state such as on 50% or even off)
4) Press and hold responder set button until it double-beeps
Keypad will double-beep and its LED will stop blinking
5) Test by tapping Keypad button on and off
Responder load will respond appropriately
Keypad button LED will turn on and off
Keypad set button will blink green once for each successful command
Keypad
(Controller)
Responder
Controller
Keypad
(Responder)
Make Keypad a Responder
Control Keypad from another INSTEON device.
1) Press and hold controller button until it beeps
Controller LED will start blinking
2) Press and hold Keypad button to adjust load to desired brightness (or off) when
scene is activated
Connected load will respond appropriately
3) Press and hold Keypad set button until it double-beeps
Controller will double-beep and its LED will stop blinking
Keypad will double-beep
4) Test by tapping controller button on and off
Connected load will return to the state set in step #2
Owner’s Manual and Tech Support
Visit: http://www.insteon.com/support for complete manual, online tech support and latest product documents.
Call: INSTEON Support Line at 866-243-8022
FCC and IC Warnings
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
CAUTION - To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a
transformer-supplied appliance.
Gradateurs commandant une lampe a filament de tungstene – afin de reduire le risqué de surchauffe et la possibilite d’endommagement a d’autres materiels, ne pas installer pour commader une
prise, un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.
2334-222/2334-232 Rev. 6/19/2013 10:25 AM / See Owner’s Manual for Warranty Information.
Protected under U.S. and foreign patents (see www.insteon.com/patents)
© Copyright 2013 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising