ZICO - Ziamatic

ZICO - Ziamatic
Rol-Loc® Mechanical Bracket
Model QM-ROLO-SA-____
Parts and Instruction Manual
ZICO®
1027PM1
Rev 3-16-16
Self-locking - simply press the cylinder through the rolling top clamp.
The Rol-Loc features a unique self-locking, PVC-coated top clamp to
securely lock SCBA cylinders without the need for straps or levers.
To secure the cylinder, place the SCBA valve into the footplate, then press
the cylinder against the top clamp. The top clamp will roll up and out of the
way to accept the cylinder, and then lock closed behind it.
To release the SCBA, simply pull on the release cord.
NFPA compliant and third party tested to exceed the 9G standard.
Fits st SCBAs with only minor adjustments.
Easty to retrofit into new or old seats. Works with most center pull releases.
Note: Not to be used in place
of a seat belt when used with
SCBA harness.
Note: Due to slight variations in cylinder length
between SCBAs of the same make and model,
Zico strongly recommends the purchase of the
Rol-Loc Adjustable Footplate Kit.
MODEL
DESCRIPTION
WT./@ IN LBS.
QM-ROLO-SA
Bracket, Stand Alone
18.3
QM-ROLO-SA-LSPR Bracket, Stand Alone less Pull Release
17.9
QM-AF-R
Adjustable Footplate Kit
0.6
Page 2
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
1
1027-110-101 Back Plate, Stand Alone
1
Rol-Loc
2
1027-110-103 Upper Strap
1
3
1027-110-105 Upper Bracket
1
4
1027-105-910 Bumper Spring Assem.
1
5
1027-105-133 Cyl. Stop, 3/4 x 5/8,
1
5/16-18 Thrd.
6
9015-173100 5/16-18 NylockIns. Nut,
4
ZPS, GR. 5
7
1027-105-101 Rotational Block Casting
1
8
9015-102512 1/4-20 x 3/4 Screw,
4
Hex Hd.
4
10
9015-172500 1/4-20 Nylock Ins Nuts,
ZPS, GR. 5
11
1027-105-111 Rotational Block Return
1
Spring
12
1090-000-150 Rubber Bumper (ACSR)
1
13
1045-320-106 Foot Plate Guide
1
14
1029-105-127 Foot Plate Mounting
1
Block
4
15
9014-203100 Lockwasher, 5/16 Dia.,
Split
16
9018-103116 Screw, 5/16-18 x 1" HH,
2
Gr 8
17
9070-002020 Clevis Pin, ZPS, 1/2" x
2
1-1/2"
18
1027-110-109 MSA Extension
1
(Optional)
19
9140-100612 Spring Pin, S/S, 1/16" x
1
3/4"
20
1027-105-139 Cable Guide
1
21
1045-320-169 Yellow Knob
1
22
1045-320-185 Knob Retainer
1
23
9010-391603 Retainer Set Screw
1
24
1027-105-131 Yellow Tubing, 10"
1
25
1010-175-131 Barb
1
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
26
1027-105-125 Pull Release Bracket
1
27
1027-105-127 Pull Release Cable
1
28
1027-105-129 Conduit w/Crimped
1
Fitting
29
1045-320-115 Footplate Adjuster Block
1
30
9120-101305 #6 x 5/16 SS Drive
1
Screw
31
1027-105-135 Pull Release Bracket Top
1
32
1027-105-137 Push Nut (for 6mm rod)
1
33
9010-352012 Screw, 10-32 x 3/4 BH
3
ZPS Allen
34
9013-252000 Nut, 10-32 Hex Nylon
4
Lock
35
9070-001212 Cotter Pin, 1/8 x 3/4
2
Steel
4
36
9010-162510 1/4-20 x 5/8" FH, PHIL
82 Deg., ZPS
37
9014-202500 Lockwasher, 1/4 Split
4
38
9010-222010 Screw, 10-32 x 5/8, PH,
1
PHIL, ZPS
1
39
9014-132500 Washer, 1/4 Dia., Gr. 8,
1/16 Thk
40
9025-172006 Screw, 10-32 x 3/8, ZPS
2
41
9010-103124 Screw, 5/16-18 x 1-1/2
2
Hex Hd., ZPS
5
42
9014-113100 Flatwasher, 5/16ø NOM.,
ZPS
43
1045-320-139 Spacer, 3/8
2
44
9010-103112 Screw, 5/16-128 x 3/4,
1
Hex Hd., ZPS
45
9010-573124 Stud, 5/16-18 x 1-1/2, ZPS
1
46
9010-573132 Stud, 5/16-18 x 2, ZPS
1
47
9112-203100 Nut, Jam 5/16-18 THIN, SS
1
48
9114-112500 Washer, 1/4 Dia. SS
4
1
49
9010-562520 Screw, 1/4-20 x 1/4"
Torx Pan, ZPS
Page 3
Preparing to Install
To provide optimum performance, the Rol-Loc must be
mounted properly for the specific SCBA, air cylinder size,
and seat model being used.
Your seat may need to be re-adjusted to fit your SCBA
combination efficiently.
The Rol-Loc bracket should be installed such that
the Rol-Loc (when rotated open) does not bind with
any part of the seat - including the head rest.
Verify that the SCBA and Rol-Loc will fit around any
structural members (tubing) near the bottom of the
seat. The seat brackets (or shroud) may need to be
adjusted in or out and up or down. Also, you may
have to raise or lower the Rol-Loc bracket to achieve
correct clearance.
Mounting the Rol-Loc to a seat
Here are some factors to be taken into consideration when
mounting an SCBA bracket in a seat:
•
•
1.
2.
3.
• Make sure the seat SCBA mounting brackets (or
shroud) is adjusted back far enough to provide
adequate clearance between the SCBA and the seat
cushion.
Remove the 5/16-18 x 3/4" hex bolt from the spring
assembly and detach the assembly from the bracket
Find the position where the spring assembly mounting
hole and bottom mounting hole line up to existing seat
bracket mounting holes. (In some cases you may need
to make a mounting hole.)
Using the mounting hardware provided (5/16-18 x
1-1/2" hd bolt) position the bolt through the spring
assembly in the specific position found in the chart
provided below.
Hole
Position
SCBA Cylinder Size
1
60 Min. Cyl.
2
45 Min., 30 Min. LP 2216 PSI,
30 Min. 3000 PSI
3
45 Min., 30 Min. LP 2216 PSI,
30 Min. 3000 PSI
4
30 Min. HP 4500 PSI
Note: Position 2 and 3 can be selected based on
fitting preference.
4. Take the spring assembly with the bolt in the correct
position and mount it through the back plate in the
same hole the spring assembly was unmounted from.
Page 4
5.
6.
7.
8.
Apply the 3/8" spacer to the back of the bracket's
backplate, onto the bolt holding the spring.
Mount the bracket with the spacer to the seat's
mounting strap or shroud. Secure with a flat washer
and 5/16-18 lock nut. (Do not tighten yet.)
Apply the lower mounting bolt with a flat washer
through the lower mounting hole using the second
spacer provided and secure with a lock nut.
Tighten top and bottom mounting bolts.
3. Loosen the T-30 torx head screw holding the footplate
guide enough to allow it to slide back and forth on the
footplate.
4. Place the SCBA cylinder valve in the footplate
assembly. Keep the cylinder valve assembly as far
forward as it will go and slide the footplate guide
so there is approximately 3/8" clearance between the
guide and the cylinder valve.
Rol-Loc Adjustment Procedure
1.
2.
Measure the overall length of your SCBA Air Cylinder
from the bottom of the valve to the top of the cylinder.
Adjust the length between the footplate to the upper
strap. The distance should be the length of your
SCBA cylinder plus anywhere from 1/8" to a 1/2" for
clearance of the upper strap.
5.
6.
Page 5
Remove the SCBA cylinder from the footplate and
retighten the T-30 torx head screw holding the
footplate guide.
Place your SCBA cylinder in the bracket and adjust
the bumper bottle stop so that there is a 1/4" clearance
from the bumper to the cylinder.
7.
Attach the pull release bracket with the yellow tube
and cable to the desired location on the seat frame by
drilling (2) holes with a #19 drill (.166). Use (2)
10-32 x 3/8" thread forming screws to attach the
bracket. (Thicker seat frame may require larger drill
size, #18 .169.) Be sure to carefully run the cable and
conduit around the seat and bracket without causing
kinks in the cable housing or interference with the
bracket's functioning.
8. Check the pull release for proper function.
9. If you place your cylinder in the bracket and feel it is
loose, you may adjust the spring assembly to another
position.
If using the Rol-Loc with an MSA SCBA cylinder, you must read this important safety
information:
TO SAFELY SECURE YOUR MSA SCBA
If your MSA SCBA cylinder uses a gauge guard with the approximate dimensions shown in Ref. A, you must use the
included adapter plate as shown in Ref. B, secured to the inside of the footplate as shown.
If your MSA SCBA cylinder has a smaller gauge guard, this adapter should not be used. Damage may result when
using the adapter with a smaller gauge guard.
If your MSA SCBA is a Model G1, you must use the included Footplate Riser as shown in Ref. C, secured to the Footplate
with double-sided tape (included). The adapter plate should not be used.
Ref. A
Ref. B
Ref. C
www.ziamatic.com
TOLL FREE: 800-711-3473
10 West College Avenue, P.O. Box 337, Yardley, PA 19067-0587 • (215) 493-3618 • FAX: (215) 493-1401
Ziamatic Corp.
*ZICO is a registered trademark for fire, safety and marine products made by Ziamatic Corp.
Page 6
Copyright Ziamatic Corp. 3-16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising