GTD33EASK - Webcollage.net
GTD33EASK
GE Appliances 7.2 Cu. Ft. Capacity
Aluminized Alloy Drum Electric Dryer
22 1/2"
29 1/2"
27"
Power Cord 4 1/2"
26"
11 3/4"
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRIC DRYER RATING:
240V
5600W
24A
60Hz
208V
4400W
22A
60Hz
44"
37 1/2"
EXHAUST OPTION: 4-way rear, right,
left and bottom
CIRCUIT REQUIREMENTS: An
individual, properly-grounded branch
circuit, protected by a 30-amp circuit
breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be
located within 36" of service cord entry
and acessible when dryer is mounted in
position.
INSTALLATION INFORMATION:
For complete information, see installation
instructions packed with your dryer.
8"
3 1/2"
Side View
1 3/4"
5"
3 1/4"
Rear View
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- I f your dryer is approved for installation in an alcove or closet, it will be stated on a label on
the dryer back.
-T
he dryer MUST be exhausted to the outside.
-M
inimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 1" front, top and rear
-C
loset doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.
of open area equally distributed. If this closet contains both a washer and a dryer, doors must
contain a minimum of 120 sq. in. of open area equally distributed.
- No
other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
-T
he dryer MUST be exhausted to the outdoors.
-T
he installation must conform with the local codes, or in the absence of local codes, with the
National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
-M
inimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION­:
Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Listed by
Underwriters
Laboratories
Specification Revised 7/16
GE Dryer Vent
GTD33EASK
GE Appliances 7.2 Cu. Ft. Capacity
Aluminized Alloy Drum Electric Dryer
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED WITH
YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If
rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit
WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent
using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY
in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where
a 4" diameter can be maintained throughout the entire length of the transition duct. Please see
installation instruction packed with your dryer for complete instructions when using flexible metal
(foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown
in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house
floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture
could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
GE Dryer Vent
DRYER EXHAUSTING INFORMATION—
USE METAL DUCT ONLY VERTICAL AND
HORIZONTAL DUCTING
BEST PERFORMANCE
Maximum length
of 4" dia rigid
A 4
metal duct
B
Exhaust hood type
A
Number
A
B
of 90°
4"
2-1/2"
4
2-1/2
Domestic dryer
turns
opening opening
B models
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2-1/2
Long Vent 6.1-7.4 cu. ft.
2
85 ft.
65 ft.
capacity electric & gas
3
70 ft.
55 ft.
(GTD33, GTD42, GTD45,
4
60 ft.
45 ft.
GTD65, GTX22, GTX33, GTX42
and GTX65)
5
55 ft.
35 ft.
A
For every extra 90° elbow, reduce the allowable vent system
length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all
the straight portions and elbows of the system (including the
transition duct.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.
The wall cap must also be located at least 12" above the ground or any other obstruction with the
opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL
1-800-GE-CARES.
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 7/16
GTD33EASK
GE Appliances 7.2 Cu. Ft. Capacity
Aluminized Alloy Drum Electric Dryer
FEATURES AND BENEFITS
Aluminized alloy drum – Improves energy efficiency and resists corrosion
3 heat selections – Offer a choice of drying temperatures for personalized
fabric care.
Up to 120 ft. venting capability – Provides flexible installation
Auto Dry – For clothes that come out feeling and looking great, this setting
monitors air temperature to set the optimal drying time
Rotary electromechanical controls – Make it simple to set cycles
Up-front lint filter – Makes cleaning out lint easy
Reverse-a-door – Door opening can be reversed to meet laundry room needs
Model GTD33EASKWW – White
GTX33EASKWW_GTX33GASKWW_GTX33GASKWW_GTD33GASKWW
Specification Revised 7/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising