Modular FRL Units

Modular FRL Units
New
Modular F.R.L. Units
Regulator
Set pressure:
Interchangeability
Selection of pressure gauges
Interchangeable
with the current
AR series by
panel mounting
0.05 to 0.85 MPa
0.02 to 0.2 MPa
Better visibility & environmental resistance
Double
layer
design
RoHS
Square embedded type
Round type Digital pressure
pressure gauge
pressure gauge
switch
The bowl is covered with
a transparent bowl guard!
¡The inside is visible from 360°.
¡The bowl is completely protected from the environment. Safety improved
Inner bowl
Transparent bowl guard
Material: Polycarbonate
Material: Polycarbonate
∗ Body size: 30 or more
Easy replacement of the element
The element and the bowl are in one piece. Replacement
in hand!
Replacement can be done in hand.
Existing model
New
∗ AF-A only
(Except AF10-A,
AF50-A, AF60-A)
Reduced required maintenance space
Regulator with backflow function AR0K is available.
AF40-A
AF40
75 mm
40 mm
Max.
46%
reduction
∗ For AF40-A
Regulator
Lubricator
35 mm
Series AC
reduction
Air Filter
Mist Separator
Filter Regulator
Lubricator
Filter Regulator
Mist Separator
Air Filter
Regulator
CAT.EUS40-60A-UK
Series AC
Transparent bowl guard
Better environmental resistance:
Transparent bowl guard can protect the inner bowl!
Windows on the bowl guard are abolished and
the inner bowl is covered with “polycarbonate
transparent bowl guard”. Even when the
product is used in an ambient environment
where it is exposed to chemicals or oil, which
do not stick to the bowl where the internal
pressure is applied. This can reduce direct
effects on the bowl.
Double layer
Existing
design
model
Pressure
Pressure
Transparent
rd
d
bowl guard
Applicable model
Air Filter
AF
Mist Separator
AFM
Cracks may occur
in a portion where
the internal pressure
is applied.
Lubricator
AL
Micro Mist Separator
AFD
Inner bowl
Bowl guard
Inner bowl
Transparent bowl guard
Filter
Regulator
AW:0(K)-B
Body size: 30 or more
Better visibility: 360°
Use of transparent bowl guard makes it possible to check the condensate inside the
filter case and the remaining oil amount in the lubricator from the entire periphery.
Light weight:
Metal related corrosion
does not occur.
Max. 90 g reduction
Except AW
AW10-A
AW첸0(K)-B
Existing model: AW첸0
AF40-A
AF40-A
AF40
AF40
Weight
360 g
Weight
450 g
Resin body does not rust.
Condensate can
be monitored from
anywhere.
New Spacer
Modular connection
Step :
Step @
Mount the product by lining up the mating surface of the
new spacer with bracket.
# Insert the retainer into the spacer bolt and tighten the
nut. (temporary assembling)
#
#
Spacer with bracket
Tighten the nut with the hexagon wrench.
Interchangeable with existing model
#
#
New spacer can be connected to existing AF, AR, AL, AW series.
Existing spacer can be connected to the New AF;-A, AR;(K)-B, AL;-A,
AW;(K)-B series.
Retainer
Nut
Tentative
tightening
by fingers
is possible.
1
Modular F.R.L. Units
Series AC
Port size
Model
INDEX
+ Lubricator
Filter Regulator
AW
AL
+ Regulator
Air Filter
Air Combination
AF
Air Filter
AR
+ Mist Separator + Regulator
AFM
AR
AF AR AL
AC10-A
AC20-B
AC25-B
AC30-B
AC40-B
AC40-06-B
AC50-B
AC55-B
AC60-B
P.7
AC10A-A
AC20A-B
AC30A-B
AC40A-B
AC40A-06-B
AC50A-B
AC60A-B
P.15
AC10B-A
AC20B-B
AC25B-B
AC30B-B
AC40B-B
AC40B-06-B
AC50B-B
AC55B-B
AC60B-B
P.21
AC20C-B
AC25C-B
AC30C-B
AC40C-B
AC40C-06-B
P.27
AC20D-B
AC30D-B
AC40D-B
AC40D-06-B
P.31
AW
+ Mist Separator
AFM
AW
Filter Regulator
AL
AR
AF
1
AW AL
AL
3/4
AF AR
AR
1/2
AF AFM AR
AF
+ Lubricator
3/8
AW AFM
+ Regulator
1/4
AF
Air Filter
1/8
Attachment
M5
AFM / AFD
Product
AC
Series Configuration
2
Series AC
Series Configuration
Port size
Product
Model
INDEX
M5
AF
1/8
1/4
3/8
1/2
3/4
1
AF10-A
AF20-A
Air Filter
AF30-A
AF40-A
P.43
AF40-06-A
AF50-A
AF60-A
AFM
AFM20-A
Mist Separator
AFM30-A
AFM40-A
P.53
AFM40-06-A
Micro Mist Separator
AFD
AFD20-A
AFD30-A
AFD40-A
P.53
AFD40-06-A
AR
AR10-A
AR20-B
Regulator
AR25-B
AR30-B
AR40-B
P.62
AR40-06-B
AR50-B
AR60-B
Regulator with
Backflow Function
AR쏔K
AR20K-B
AR25K-B
AR30K-B
AR40K-B
AR40K-06-B
AR50K-B
AR60K-B
3
P.65
Series
AC
Port size
Product
Model
INDEX
AL
1/8
1/4
3/8
1/2
3/4
1
AF AR AL
M5
AL10-A
AL20-A
AL30-A
AL40-A
P.76
AW AL
Lubricator
AC
Modular F.R.L. Units
AL40-06-A
AL50-A
AW
AF AR
AL60-A
AW10-A
Filter Regulator
AW30-B
AF AFM AR
AW20-B
P.84
AW40-B
AW40-06-B
AW쏔K
Attachment
AW AFM
AW60-B
AW20K-B
AW40K-B
P.87
AW40K-06-B
A system designed to respond quickly
and easily to your special ordering needs
AR
Simple Specials System
AFM / AFD
AF
AW60K-B
Short lead times
AL
This system enables us to respond to your special needs, such as
additional machining, accessory assembly, or modular unit, and
deliver such special products as quickly as standard products.
Repeat orders
Once we receive a Simple Special part number from your previous
order, we will process the order, manufacture the product, and
deliver it to you.
AW
Filter Regulator with
Backflow Function
AW30K-B
4
Series
AC
Attachment List
Check valve
Page 34
왎 A check valve with intermediate branch port can be easily
installed to prevent a backflow of lubricant when branching the
air flow and releasing the air on the outlet side of the regulator.
Pressure switch
Page 35
왎 A compact integrated pressure switch can be easily installed and
facilitates the pressure detection of the line.
Pressure switch
T-spacer
Page 35
왎 Using a T-shaped spacer facilitates the branching of air flow.
Applicable series
T-spacer
왎 Pipings are possible in all 4 directions.
· Air Filter + Regulator + Lubricator (AC20-B to AC60-B)
· Filter Regulator + Lubricator (AC20A-B to AC60A-B)
· Air Filter + Regulator (AC20B-B to AC60B-B)
· Air Filter + Mist Separator + Regulator (AC20C-B to AC60C-B)
· Filter Regulator + Mist Separator (AC20D-B to AC60D-B)
Pressure relief 3 port valve
왎 With the use of a pressure relief 3 port valve, pressure left in the line
can be easily exhausted.
Page 36
· Air Filter + Regulator + Lubricator (AC20-B to AC50-B)
· Filter Regulator + Lubricator (AC20A-B to AC50A-B)
· Air Filter + Regulator (AC20B-B to AC50B-B)
· Air Filter + Mist Separator + Regulator (AC20C-B to AC40C-B)
· Filter Regulator + Mist Separator (AC20D-B to AC40D-B)
Piping adapter
Piping adapter
5
Page 37
왎 A piping adapter allows installation/removal of the component
without removing the piping and thus makes maintenance easier.
Cross spacer
∗ Needs to be ordered separately.
Page 36
Pressure relief 3 port valve
· Air Filter + Regulator + Lubricator (AC10-A to AC60-B)
· Air Filter + Regulator (AC10B-A to AC60B-B)
· Air Filter + Mist Separator + Regulator (AC20C-B to AC40C-B)
Cross spacer
Applicable series
· Air Filter + Regulator + Lubricator (AC20-B to AC40-B)
· Filter Regulator + Lubricator (AC20A-B to AC40A-B)
∗ Port size: Except 06
Applicable series
Applicable series
Check valve
∗ Needs to be ordered separately.
Page 37
Accessories (Spacer/Spacer with bracket)
AC
Pressure switch with piping adapter
Series AC
Page 38
AF AR AL
Modular F.R.L. Units
Spacer
Pressure switch with
piping adapter
AW AL
Spacer with
bracket
AF AR
Spacer with bracket
∗ Needs to be ordered separately.
AF AFM AR
∗ Needs to be ordered separately.
Related Product
AW AFM
Modular adapter
Easy modular connections for all equipment!
Attachment
Example) Air filter + 3 port valve
Hexagon
socket
Uni 1/8 to 1/2
AF
3 port valve
AFM / AFD
Modular adapter (E310-U02)
Spacer with bracket (Y300T-A)
AW
AL
AR
Air filter (AF30-A)
6
Air Combination
Air Filter + Regulator + Lubricator
AC10-A
1
A
q
w
e
Option
q
앬
Float type auto drain
C
Refer to page 9 for size 20 to 60.
• Option/Semi-standard: Select one each for a to h.
• Option/Semi-standard symbol: When more than one specification is required,
indicate in alphanumeric order.
Example) AC10-M5CG-T-12NR-A
Symbol
a
2
L
How to Order
AC10 M5
Symbol
Description
—
Without auto drain
Note 1)
N.C. (Normally closed) Drain port is closed when pressure is not applied.
+
b
Pressure gauge
G
—
Without pressure gauge
Note 2)
Round type pressure gauge (without limit indicator)
+
w
앬
Attachment (T-spacer) Note 3)
—
Without attachment
T
Mounting position: AF+T+AR+AL
+
c
Set pressure Note 4)
—
0.05 to 0.7 MPa setting
1
0.02 to 0.2 MPa setting
+
d
Bowl Note 5)
—
Polycarbonate bowl
2
Metal bowl
6
Nylon bowl
e
앬
Semi-standard
+
e
Lubricator lubricant
exhaust port
—
Without drain cock
3
Lubricator with drain cock
+
f
Exhaust mechanism
—
Relieving type
N
Non-relieving type
+
g
Flow direction
—
Flow direction: Left to right
R
Flow direction: Right to left
+
h
Pressure unit
—
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Z
Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
Note 1) When pressure is not applied, condensate which does not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending operations for the day is recommended.
Note 2) A 1.0 MPa pressure gauge will be fitted. It is not assembled and supplied loose at the time of shipment.
Note 3) The bracket position varies depending on the T-spacer mounting.
Note 4) Pressure can be set higher than the specification pressure in some cases, but use pressure within the specification range.
Note 5) Refer to Chemical data on page 46 for chemical resistance of the bowl.
7
Series AC10-A
AC
Air Combination
AF AR AL
AC10-A
Air Filter [AF]
AF10-A
Regulator [AR]
AR10-A
Lubricator [AL]
AL10-A
Port size
M5 x 0.8
Pressure gauge port size [AR]
1/16
Air
Ambient and fluid temperature
AF AR
Fluid
–5 to 60°C (with no freezing)
Proof pressure
1.5 MPa
Maximum operating pressure
1.0 MPa
0.05 to 0.7 MPa
Nominal filtration rating [AF]
5 μm
Recommended lubricant [AL]
Class 1 turbine oil (ISO VG32)
Bowl material [AF/AL]
Polycarbonate
Construction [AR]
Relieving type
Weight [kg]
AF AFM AR
Set pressure range [AR]
0.27
AW AFM
Component
AW AL
Standard Specifications
Attachment
Specific Product Precautions
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
Selection
Caution
AW
AL
AR
AFM / AFD
AF
1. When releasing air at the intermediate position using a
T-spacer on the inlet side of the lubricator, lubricant may back
flow. Therefore, releasing air that does not contain traces of
lubricant is not possible.
2. An F.R.L. unit shipped from the plant has its model number
labeled. However, components that are combined together
during the distribution process do not have a label on them.
8
Air Combination
Air Filter + Regulator + Lubricator
Symbol
AC20-B to AC60-B
B
03 DE
q
w
e
r
t
y
2
L
Refer to page 7 for size 10.
How to Order
AC 30
1
• Option/Semi-standard: Select one each for a to m.
• Option/Attachment/Semi-standard symbol: When more than
one specification is required, indicate in alphanumeric order.
Example) AC30-F03DE1-KSTV-136NR-B
q
앬
Symbol
Description
Body size
20
w
앬
Pipe thread type
—
N Note 1)
F Note 2)
Port size
01
02
03
04
06
10
25
30
40
50
55
60
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Rc
NPT
G
+
e
앬
1/8
1/4
3/8
1/2
3/4
1
—
—
—
—
+
a
Float type
auto drain
Without auto drain
—
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
—
r
앬
Option Note 3)
+
Pressure
gauge Note 6)
b
Digital
pressure
switch
—
E
G
M
E1
E2
E3
E4
Without pressure gauge
Square embedded type pressure gauge (with limit indicator)
Round type pressure gauge (with limit indicator)
Round type pressure gauge (with colour zone)
Output: NPN output/Electrical entry: Wiring bottom entry
Output: NPN output/Electrical entry: Wiring top entry
Output: PNP output/Electrical entry: Wiring bottom entry
Output: PNP output/Electrical entry: Wiring top entry
+
c
Check valve
—
K
Without attachment
Mounting position: AF+AR+K+AL
Note 7)
t
앬
Attachment
+
d
Pressure
switch
Without attachment
—
S Note 8) Mounting position: AF+AR+S+AL
+
e
T-spacer
f
Pressure relief
3 port valve
—
Without attachment
T Note 8) Mounting position: AF+T+AR+AL
+
—
V
Without attachment
Mounting position: AF+AR+AL+V
+
y
앬
9
Semi-standard
g
Set
pressure Note 9)
—
1
Bowl Note 10)
—
2
6
8
C
6C
0.05 to 0.85 MPa setting
0.02 to 0.2 MPa setting
+
h
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
Nylon bowl with bowl guard
—
— Note 11) — Note 11) — Note 11) — Note 11) — Note 11) — Note 11)
— Note 12) — Note 12) — Note 12) — Note 12) — Note 12) — Note 12)
Series AC20-B
to AC60-B
AC20-B
AC40-B
q
앬
Description
Body size
20
j
Without drain cock
—
Lubricator lubricant
exhaust port
3 Note 16) Lubricator with drain cock
30
40
50
55
60
—
—
—
—
—
—
—
—
AF AR
i
With drain cock
—
Drain guide 1/8
Air filter
J Note 14)
drain port Note 13)
Drain guide 1/4
W Note 15) Drain cock with barb fitting (for ø6 x ø4 nylon tube)
25
AF AFM AR
Flow direction
—
R
Relieving type
Non-relieving type
+
l
Flow direction: Left to right
Flow direction: Right to left
+
m
Pressure unit
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Z Note 17) Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
ZA Note 18) Digital pressure switch: With unit conversion function
Note 1) Drain guide is NPT1/8 (applicable to the AC20-B)
and NPT1/4 (applicable to the AC25-B to AC60-B).
The auto drain port comes with ø3/8" One-touch
fitting (applicable to the AC25-B to AC60-B).
Note 2) Drain guide is G1/8 (applicable to the AC20-B) and
G1/4 (applicable to the AC25-B to AC60-B).
Note 3) Option G, M are not assembled and supplied loose
at the time of shipment.
Note 4) When pressure is not applied, condensate which
does not start the auto drain mechanism will be left
in the bowl. Releasing the residual condensate
before ending operations for the day is
recommended.
Note 5) If the compressor is small (0.75 kW, discharge flow
is less than 100 L/min[ANR]), air leakage from the
drain cock may occur during start of operations.
N.C. type is recommended.
Note 6) When the pressure gauge is attached, a 1.0 MPa
pressure gauge will be fitted for standard (0.85
MPa) type. 0.4 MPa pressure gauge for 0.2 MPa
type.
Note 7) Not available with piping port size: 06
Note 8) The bracket position varies depending on the
T-spacer or pressure switch mounting.
Note 9) Pressure can be set higher than the specification
pressure in some cases, but use pressure within
the specification range.
Note 10) Refer to Chemical data on page 46 for chemical
resistance of the bowl.
Note 11) A bowl guard is provided as standard equipment
(polycarbonate).
Note 12) A bowl guard is provided as standard equipment
(nylon).
Note 13) The combination of float type auto drain: C and D
is not available.
Note 14) Without a valve function
Note 19)
Note 19)
Note 19)
Note 19)
Note 19)
Note 19)
Note 19)
Note 20)
Note 20)
Note 20)
Note 20)
Note 20)
Note 20)
Note 20)
Note 15) The combination of metal bowl: 2 and 8 is not
available.
Note 16) When choosing with W: Filter drain port, the drain
cock of a lubricator will be with barb fittings.
Note 17) For pipe thread type: NPT.
Cannot be used with M: Round pressure gauge
(with colour zone). Available by request for
special.
The digital pressure switch will be equipped with
the unit conversion function, setting to psi initially.
Note 18) For options: E1, E2, E3, E4.
Note 19) 쑗: For pipe thread type: NPT only
Note 20) 왕: Select with options: E1, E2, E3, E4.
AF
—
Standard Specifications
AC30-B
AF30-A
AR30-B
AL30-A
1/4, 3/8
1/4, 3/8
0.70
0.78
AC40-B
AF40-A
AR40-B
AL40-A
AC40-06-B
AF40-06-A
AR40-06-B
AL40-06-A
AC50-B
AF50-A
AR50-B
AL50-A
1/4, 3/8, 1/2
3/4
3/4, 1
1/8
Air
–5 to 60°C (with no freezing)
1.5 MPa
1.0 MPa
0.05 to 0.85 MPa
5 μm
Class 1 turbine oil (ISO VG32)
Polycarbonate
Standard (Polycarbonate)
Relieving type
1.39
1.53
3.43
AC55-B
AF60-A
AR50-B
AL60-A
AC60-B
AF60-A
AR60-B
AL60-A
1
1
3.71
3.76
AL
AC25-B
AF30-A
AR25-B
AL30-A
AW
Model
AC20-B
Air Filter [AF]
AF20-A
Component Regulator [AR]
AR20-B
Lubricator [AL]
AL20-A
Port size
1/8, 1/4
Pressure gauge port size [AR] Note 1)
Fluid
Ambient and fluid temperature Note 2)
Proof pressure
Maximum operating pressure
Set pressure range [AR]
Nominal filtration rating [AF]
Recommended lubricant [AL]
Bowl material [AF/AL]
Semi-standard (Steel)
Bowl guard [AF/AL]
Construction [AR]
Weight [kg]
0.39
AW AFM
k
—
N
Attachment
+
Exhaust
mechanism
AFM / AFD
y
앬
Semi-standard
+
AR
Symbol
AW AL
AF AR AL
AC
Air Combination
Note 1) Pressure gauge connection threads are not available for F.R.L. unit with a square embedded type pressure gauge or with a digital pressure switch.
Note 2) –5 to 50°C for the products with the digital pressure switch
10
AC10-A
Series AC20-B to AC60-B
Series
Flow-rate Characteristics (Representative values)
AC10-A
M5 x 0.8
AC20-B
Rc1/4
0.4
0.3
0.2
0.1
25
50
75
100
125
0.5
0.4
0.3
0.2
0.1
0
0
150
200
AC30-B
Rc3/8
0.4
0.3
0.2
0.1
0
0
800
Rc1/2
0.4
0.3
0.2
0.1
1000
0.4
0.3
0.2
0.1
0
0
1000
Flow rate L/min (ANR)
Rc1
2000
0.4
0.3
0.2
0.1
0
0
3000
Rc1
0.4
0.3
0.2
0.1
2000
4000
6000
8000
0.5
0.4
0.3
0.2
0.1
0
10000
2000
0
4000
Pressure Characteristics (Representative values)
6000
8000
0.4
0.3
0.2
0.1
0
2000
0
6000
8000
10000
Conditions: Inlet pressure 0.7 MPa, Outlet pressure 0.2 MPa, Flow rate 20 L/min (ANR)
AC25-B
0.25
Set point
0.2
Outlet pressure [MPa]
0.2
Outlet pressure [MPa]
Set point
4000
Flow rate L/min (ANR)
0.25
0.25
5000
0.5
10000
AC20-B
0.3
4000
Rc1
Flow rate L/min (ANR)
Flow rate L/min (ANR)
AC10-A
3000
0.6
Outlet pressure [MPa]
Outlet pressure [MPa]
0.5
2000
AC60-B
0.6
0
0
1000
Flow rate L/min (ANR)
AC55-B
0.6
Rc3/4
0.5
Flow rate L/min [MPa]
AC50-B
1500
0.6
0.5
1500
1000
AC40-06-B
Outlet pressure [MPa]
0.5
500
500
Flow rate L/min (ANR)
0.6
Outlet pressure [MPa]
Outlet pressure [MPa]
600
AC40-B
0.6
Outlet pressure [MPa]
400
0.5
Flow rate L/min (ANR)
Flow rate L/min (ANR)
0
0
Rc3/8
0.6
Outlet pressure [MPa]
Outlet pressure [MPa]
0.5
0
0
Outlet pressure [MPa]
AC25-B
0.6
0.6
Outlet pressure [MPa]
Condition: Inlet pressure 0.7 MPa
Set point
0.2
0.15
0.15
0.15
0 0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0
1.0
0
0.2
0.3
AC30-B
Set point
0.2
Outlet pressure [MPa]
Outlet pressure [MPa]
0.6
0.7
0.8
0.9
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
0
0.2
0.3
0.9
1.0
0.5
0.6
0.7
0.8
0.9
1.0
AC40-06-B
0.25
Set point
0.2
0
0.4
Inlet pressure [MPa]
Set point
0.2
0.15
0.15
0
0
1.0
0.25
0.15
11
0.5
AC40-B
0.25
0
0.4
Inlet pressure [MPa]
Inlet pressure [MPa]
Outlet pressure [MPa]
0
0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
0.9
1.0
0
0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
0.9
1.0
Series AC10-A
Air Combination
Air Combination
Pressure Characteristics (Representative values)
0.7
0.8
0.9
1.0
0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0
0
AC
AF AR AL
0.2
0.3
Inlet pressure [MPa]
0.4
0.5
0.6
0.7
0.8
0.9
1.0
AW AL
0.6
Inlet pressure [MPa]
Specific Product Precautions
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
Mounting/Adjustment
Caution
Selection
Warning
1. A knob cover is available to prevent careless operation of the
knob. Refer to page 97 for details.
Piping
Warning
1. When mounting a check valve, make sure the arrow (IN side)
points in the correct direction of air flow.
Air Supply
Caution
1. Use an air filter with 5 μm or less filtration rating on the inlet
side of the valve to avoid any damage to the seat caused by
dust when mounting a pressure relief 3 port valve on the inlet
side.
Mounting/Adjustment
Caution
1. When the bowl is installed on the air filter, filter regulator, lubricator, mist separator, or micro mist separator (AC25-B to
AC60-B), install them so that the lock button lines up to the
groove of the front (or the back) of the body to avoid drop or
damage of the bowl.
Lock button
1. Float type auto drain
Operate under the following conditions to avoid malfunction.
<N.O. type>
· Operating compressor: 0.75 kW (100 L/min (ANR)) or more.
When using 2 or more auto drains, multiply the value above
by the number of auto drains to find the capacity of the
compressors you will need.
For example, when using 2 auto drains, 1.5 kW (200 L/min
(ANR)) of the compressor capacity is required.
· Operating pressure: 0.1 MPa or more
<N.C. type>
· Operating pressure for AD27-A: 0.1 MPa or more
Operating pressure for AD37-A/AD47-A: 0.15 MPa or more
2. Use a regulator or filter regulator with backflow function when
mounting a pressure release 3 port valve on the inlet side to
ensure the release of the residual pressure. Otherwise,
residual pressure will not be fully released.
Caution
1. When releasing air at the intermediate position using a
T-spacer on the inlet side of the lubricator, lubricant may back
flow. Therefore, releasing air that does not contain traces of
lubricant is not possible.
To release air that does not contain traces of lubricant, use a
check valve (Series AKM) on the inlet side of the lubricator to
prevent a backflow of the lubricant.
2. If a pressure relief 3 port valve is mounted on the inlet side of
the lubricator, causing a backflow of air, it can result in a backflow of oil or damage to internal parts. Do not use it in this
fashion.
3. An F.R.L. unit shipped from the plant has its model number labeled. However, components that are combined together during the distribution process do not have a label on them.
12
AF AR
0.5
Inlet pressure [MPa]
AF AFM AR
0.4
AW AFM
0.3
Attachment
0.2
0.15
AF
0
0
AFM / AFD
0.15
0.2
AR
0.15
0.2
Set point
AL
0.2
0.25
Set point
Outlet pressure [MPa]
Outlet pressure [MPa]
Outlet pressure [MPa]
AC60-B
0.25
Set point
0
Conditions: Inlet pressure 0.7 MPa, Outlet pressure 0.2 MPa, Flow rate 20 L/min (ANR)
AC55-B
0.25
to AC60-B
AW
AC50-B
Series AC20-B
AC10-A
Series AC20-B to AC60-B
Series
Dimensions
AC10-A
A
N
S
F
M
Q1
V
C
R
J
OUT
B
Q1
Q2
IN
2 x P1
(Port size)
G
Clearance for
maintenance
U
P2
(Pressure gauge port size)
Drain
AC20-B
A
N
F
M
S
IN
OUT
2 x P1
(Port size)
B
Q1
Q2
K
Q1
V
C
R
J
G
Clearance for
maintenance
U
P2
(Pressure gauge port size)
Drain
AC25-B to AC60-B
A
N
F
M
S
K
C
Q1
V
R
J
OUT
Q1
IN
2 x P1
(Port size)
G
E
13
Clearance for
maintenance
B
U
P2
Drain
(Pressure gauge port size)
AC10-A
Air Combination Series AC20-B to AC60-B
Round type pressure gauge Round type pressure gauge (with colour zone)
J
AC10-A
AC20-B
Metal bowl
With auto drain
With drain guide
With auto drain (N.O./N.C.)
1/8
Width across
flats 14
AF AR
B
B
B
Width across
flats 14
M5 x 0.8
Thread type/Rc, G:
ø10 One-touch fitting
Thread type/NPT:
ø3/8" One-touch fitting
1/8
AC25-B to AC60-B
Metal bowl with level gauge,
with drain guide
With drain guide
B
Drain cock with barb fitting
B
Dimensions
Width across
flats 17
Width across
flats 17
1/4
1/4
Width across
flats 17
Barb fitting
applicable
tubing: T0604
1/4
AW AFM
B
B
Metal bowl with drain guide
B
Metal bowl
Metal bowl
with level gauge
B
Applicable model
Optional/Semi-standard
specifications
Metal bowl with drain guide
N.O.: Black
N.C.: Grey
B
Dimensions
Metal bowl
AC25-B to AC60-B
B
Applicable model
Optional/Semi-standard
With auto drain
specifications
Centre of
piping
AF AR AL
Centre of
piping
AW AL
H
Centre of
piping
Dimensions
H
H
J
AF AFM AR
Digital pressure switch
J
B
Square embedded type pressure gauge
B
Option
AC
Series
Air Combination
B
C
E
F
1/16
87
59.9
25.5
—
1/8
126.4
87.6
35.9
—
1/8
167.4
115.1
38.1
1/8
167.4
115.1
Bracket mount
G
J
K
28
35
12.5
—
41.6
60
28.5
2 Note)
30
55.1
80
27.5
0
38.1
30
55.1
80
29.4
3.5
M
N
Q1
Q2
R
S
U
25
31
20
27
4.5
6.8
3
24.5
30
43.2
24
33
5.5
12
3.5
29
41
57.2
35
—
7
14
4
41
41
57.2
35
—
7
14
4
41
1/8
220.4
147.1
39.8
38.4
72.6
110
33.8
3.5
50
75.2
40
—
9
18
5
48
1/8
235.4
149.1
37.8
38.4
77.6
110
33.8
3
50
80.2
40
—
9
18
5
48
1/8
282.4
220.1
41.2
—
93.1
110
43.3
3.2
70
96.2
50
—
11
20
6
60
1/8
292.4
234.1
44.7
—
98.1
110
43.3
3.2
70
96.2
50
—
11
20
6
60
1/8
297.4
234.1
44.7
—
98.1
110
43.3
3.2
70
101.2
50
—
11
20
6
60
Optional specifications
Digital pressure
switch
Round type
pressure gauge
Round type
pressure gauge
(with colour zone)
With
auto
drain
With
barb
fitting
With
drain
guide
Metal
bowl
Metal bowl Metal bowl Metal bowl with
level gauge,
with drain with level
with drain guide
guide
gauge
H
J
H
J
H
J
H
J
B
B
B
B
B
B
B
—
—
—
—
ø26
26
—
—
77.9
—
—
59.3
—
—
—
첸28
29.5
첸27.8
40
ø37.5
65
ø37.5
66
104.9
—
91.4
87.4
93.9
—
—
첸28
28.5
첸27.8
39
ø37.5
64
ø37.5
65
156.8
123.6
121.9
117.6
122.1
137.6
142.1
첸28
30.4
첸27.8
40.9
ø37.5
65.9
ø37.5
66.9
156.8
123.6
121.9
117.6
122.1
137.6
142.1
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
186.9
155.6
153.9
149.6
154.1
169.6
174.1
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
188.9
157.6
155.9
151.6
156.1
171.6
176.1
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
259.9
228.6
226.9
222.6
227.1
242.6
247.1
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
273.9
242.6
240.9
236.6
241.1
256.6
261.1
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
273.9
242.6
240.9
236.6
241.1
256.6
261.1
AR
AC10-A
AC20-B
AC25-B
AC30-B
AC40-B
AC40-06-B
AC50-B
AC55-B
AC60-B
Square type
pressure gauge
Semi-standard specifications
AW
Model
V
AF
A
AFM / AFD
M5 x 0.8
AC10-A
1/8, 1/4
AC20-B
1/4, 3/8
AC25-B
1/4, 3/8
AC30-B
1/4, 3/8, 1/2
AC40-B
3/4
AC40-06-B
3/4, 1
AC50-B
1
AC55-B
1
AC60-B
P2
AL
P1
Attachment
Standard specifications
Model
Note) For the AC20-B only, the position of the pressure gauge is above the centre of the piping.
14
Air Combination
Filter Regulator + Lubricator
AC10A-A
How to Order
AC10A M5
A
q
w
e
앬
Option
q
앬
Float type auto drain
C
1
2
L
Refer to page 17 for size 20 to 60.
• Option/Semi-standard: Select one each for a to h.
• Option/Semi-standard symbol: When more than one specification is required,
indicate in alphanumeric order.
Example) AC10A-M5CG-T-12NR-A
Symbol
a
Symbol
Description
—
Without auto drain
Note 1)
N.C. (Normally closed) Drain port is closed when pressure is not applied.
+
b
Pressure gauge
G
—
Without pressure gauge
Note 2)
Round type pressure gauge (without limit indicator)
+
w
앬
Attachment (T-spacer) Note 3)
—
Without attachment
T
Mounting position: AW+T+AL
+
c
Set pressure Note 4)
—
0.05 to 0.7 MPa setting
1
0.02 to 0.2 MPa setting
+
d
Bowl Note 5)
—
Polycarbonate bowl
2
Metal bowl
6
Nylon bowl
e
앬
Semi-standard
+
e
Lubricator lubricant
exhaust port
—
Without drain cock
3
Lubricator with drain cock
+
f
Exhaust mechanism
—
Relieving type
N
Non-relieving type
+
g
Flow direction
—
Flow direction: Left to right
R
Flow direction: Right to left
+
h
Pressure unit
—
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Z
Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
Note 1) When pressure is not applied, condensate which does not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending operations for the day is recommended.
Note 2) A 1.0 MPa pressure gauge will be fitted. It is not assembled and supplied loose at the time of shipment.
Note 3) The bracket position varies depending on the T-spacer mounting.
Note 4) Pressure can be set higher than the specification pressure in some cases, but use pressure within the specification range.
Note 5) Refer to Chemical data on page 46 for chemical resistance of the bowl.
15
Series AC10A-A
AC
Air Combination
AF AR AL
AC10A-A
Filter Regulator [AW]
AW10-A
Lubricator [AL]
AL10-A
Air
Proof pressure
1.5 MPa
Maximum operating pressure
1.0 MPa
5 μm
Recommended lubricant [AL]
Class 1 turbine oil (ISO VG32)
Bowl material [AW/AL]
Polycarbonate
Construction [AW]
Relieving type
0.2
AW AFM
Weight [kg]
AF AFM AR
0.05 to 0.7 MPa
Nominal filtration rating [AW]
Attachment
Set pressure range [AW]
AF AR
–5 to 60°C (with no freezing)
AF
Ambient and fluid temperature
1/16
AFM / AFD
Fluid
M5 x 0.8
AR
Pressure gauge port size [AW]
AL
Port size
AW
Component
AW AL
Standard Specifications
16
Air Combination
Filter Regulator + Lubricator
Symbol
AC20A-B to AC60A-B
q
B
03 DE
w
e
r
t
y
2
L
Refer to page 15 for size 10.
How to Order
AC 30 A
1
• Option/Semi-standard: Select one each for a to l.
• Option/Attachment/Semi-standard symbol: When more than one
specification is required, indicate in alphanumeric order.
Example) AC30A-F03DE1-KSV-136NR-B
q
앬
Symbol
Description
Body size
20
w
앬
Pipe thread type
—
N Note 1)
F Note 2)
Port size
01
02
03
04
06
10
30
40
—
—
50
60
Rc
NPT
G
+
e
앬
1/8
1/4
3/8
1/2
3/4
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
+
a
Float type
auto drain
Without auto drain
—
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
—
r
앬
Option Note 3)
+
Pressure
gauge Note 6)
b
Digital
pressure
switch
—
E
G
M
E1
E2
E3
E4
Without pressure gauge
Square embedded type pressure gauge (with limit indicator)
Round type pressure gauge (with limit indicator)
Round type pressure gauge (with colour zone)
Output: NPN output/Electrical entry: Wiring bottom entry
Output: NPN output/Electrical entry: Wiring top entry
Output: PNP output/Electrical entry: Wiring bottom entry
Output: PNP output/Electrical entry: Wiring top entry
+
t
앬
Attachment
c
Check valve
—
K
Without attachment
Mounting position: AW+K+AL
Note 7)
—
—
+
d
Pressure
switch
e
Pressure relief
3 port valve
Without attachment
—
S Note 8) Mounting position: AW+S+AL
+
—
V
Without attachment
Mounting position: AW+AL+V
—
+
f
Set
pressure Note 9)
—
1
Bowl Note 10)
—
2
6
8
C
6C
0.05 to 0.85 MPa setting
0.02 to 0.2 MPa setting
y
앬
Semi-standard
+
g
—
—
—
Note 11)
Note 12)
—
—
Note 11)
Note 12)
—
—
Note 11)
Note 12)
—
—
Note 11)
Note 12)
+
—
h
Filter regulator
J Note 14)
drain port Note 13)
W Note 15)
17
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
Nylon bowl with bowl guard
With drain cock
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting: For ø6 x ø4 nylon tube
—
—
—
—
—
—
Series AC20A-B
to AC60A-B
AF AR AL
AC
Air Combination
AC20A-B
AC40A-B
q
앬
i
Description
Body size
20
30
40
50
60
Note 19)
Note 19)
Note 19)
Note 19)
Note 19)
Note 20)
Note 20)
Note 20)
Note 20)
Note 20)
Without drain cock
—
Lubricator lubricant
exhaust port
3 Note 16) Lubricator with drain cock
AW AL
Symbol
AF AR
+
k
Flow direction: Left to right
Flow direction: Right to left
+
—
l
Pressure unit
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Z Note 17) Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
ZA Note 18) Digital pressure switch: With unit conversion function
Note 1) Drain guide is NPT1/8 (applicable to the AC20A-B)
and NPT1/4 (applicable to the AC30A-B to
AC60A-B).
The auto drain port comes with ø3/8" One-touch
fitting (applicable to the AC30A-B to AC60A-B).
Note 2) Drain guide is G1/8 (applicable to the AC20A-B)
and G1/4 (applicable to the AC30A-B to AC60A-B).
Note 3) Option G, M are not assembled and supplied loose
at the time of shipment.
Note 4) When pressure is not applied, condensate which
does not start the auto drain mechanism will be left
in the bowl. Releasing the residual condensate
before ending operations for the day is
recommended.
Note 5) If the compressor is small (0.75 kW, discharge flow
is less than 100 L/min[ANR]), air leakage from the
drain cock may occur during start of operations.
N.C. type is recommended.
Note 6) When the pressure gauge is attached, a 1.0 MPa
pressure gauge will be fitted for standard (0.85
MPa) type. 0.4 MPa pressure gauge for 0.2 MPa
type.
Note 7) Not available with piping port size: 06
Note 8) The bracket position varies depending on the
pressure switch mounting.
Note 9) Pressure can be set higher than the specification
pressure in some cases, but use pressure within
the specification range.
Note 10) Refer to Chemical data on page 46 for chemical
resistance of the bowl.
Note 11) A bowl guard is provided as standard equipment
(polycarbonate).
Note 12) A bowl guard is provided as standard equipment
(nylon).
Note 13) The combination of float type auto drain: C and D
is not available.
Note 14) Without a valve function
Note 15) The combination of metal bowl: 2 and 8 is not
available.
Note 16) When choosing with W: Filter drain port, the drain
cock of a lubricator will be with barb fittings.
Note 17) For pipe thread type: NPT.
Cannot be used with M: Round pressure gauge
(with colour zone). Available by request for
special.
The digital pressure switch will be equipped with
the unit conversion function, setting to psi initially.
Note 18) For options: E1, E2, E3, E4.
Note 19) 쑗: For pipe thread type: NPT only
Note 20) 왕: Select with options: E1, E2, E3, E4.
AF AFM AR
Flow direction
—
R
Relieving type
Non-relieving type
AW AFM
j
—
N
Attachment
y
앬
Semi-standard
+
Exhaust
mechanism
1/4, 3/8
1/4, 3/8, 1/2
0.63
AC40A-06-B
AW40-06-B
AL40-06-A
3/4
1/8
Air
–5 to 60°C (with no freezing)
1.5 MPa
1.0 MPa
0.05 to 0.85 MPa
5 μm
Class 1 turbine oil (ISO VG32)
Polycarbonate
Standard (Polycarbonate)
Relieving type
1.15
1.25
AC50A-B
AW60-B
AL50-A
AC60A-B
AW60-B
AL60-A
3/4, 1
1
3.21
3.36
AFM / AFD
AC40A-B
AW40-B
AL40-A
AR
AC30A-B
AW30-B
AL30-A
AL
Model
AC20A-B
Filter Regulator [AW]
AW20-B
Component
Lubricator [AL]
AL20-A
Port size
1/8, 1/4
Pressure gauge port size [AW] Note 1)
Fluid
Ambient and fluid temperature Note 2)
Proof pressure
Maximum operating pressure
Set pressure range [AW]
Nominal filtration rating [AW]
Recommended lubricant [AL]
Bowl material [AW/AL]
Semi-standard (Steel)
Bowl guard [AW/AL]
Construction [AW]
Weight [kg]
0.33
AF
Standard Specifications
AW
Note 1) Pressure gauge connection threads are not available for F.R.L. unit with a square embedded type pressure gauge or with a digital pressure switch.
Note 2) –5 to 50°C for the products with the digital pressure switch
18
AC10A-A
Series AC20A-B to AC60A-B
Series
Dimensions
AC10A-A
A
J
F
M
Q1
V
C
R
S
OUT
B
Q1
Q2
IN
2 x P1
(Port size)
AC20A-B
P2
Clearance for
maintenance
G
U
(Pressure gauge port size)
Drain
A
F
M
R
S
IN
OUT
2 x P1
(Port size)
B
Q1
Q2
K
Q1
V
C
J
AC30A-B to AC60A-B
P2
Clearance for
maintenance
G
U
(Pressure gauge port size)
Drain
A
F
M
R
S
K
Q1
V
C
J
OUT
Q1
IN
2 x P1
(Port size)
G
E
19
Clearance for
maintenance
B
U
P2
(Pressure gauge port size)
Drain
AC10A-A
Air Combination Series AC20A-B to AC60A-B
Metal bowl
With auto drain
Metal bowl
AC
AC30A-B to AC60A-B
With drain guide
Metal bowl with drain guide
With auto drain (N.O./N.C.)
1/8
B
Width across
flats 14
B
Thread type/Rc, G:
ø10 One-touch fitting
Thread type/NPT:
ø3/8" One-touch fitting
1/8
AF AR
Width across
flats 14
M5 x 0.8
AC30A-B to AC60A-B
Metal bowl with level gauge,
with drain guide
With drain guide
Drain cock with barb fitting
B
Dimensions
Width across
flats 17
1/4
Width across
flats 17
1/4
Barb fitting
applicable
tubing: T0604
1/4
AW AFM
Width across
flats 17
B
B
B
Metal bowl with drain guide
B
Metal bowl
Metal bowl
with level gauge
B
Applicable model
Optional/Semi-standard
specifications
B
Dimensions
B
B
B
B
N.O.: Black
N.C.: Grey
Standard specifications
Model
P1
M5 x 0.8
AC10A-A
1/8, 1/4
AC20A-B
1/4, 3/8
AC30A-B
1/4, 3/8, 1/2
AC40A-B
3/4
AC40A-06-B
3/4, 1
AC50A-B
1
AC60A-B
P2
A
B
C Note)
E
F
G
J
K
1/16
56
59.9
47.4
—
28
25
12.5
—
Bracket mount
M
Q1
Q2
R
S
U
—
25
20
27
4.5
6.8
3
Model
AC10A-A
AC20A-B
AC30A-B
AC40A-B
AC40A-06-B
AC50A-B
AC60A-B
V
24.5
1/8
83.2
87.6
72.4
41.6
60
28.5
5
30
24
33
5.5
12
3.5
29
1/8
110.2
115.1
85.6
30
55.1
80
29.4
3.5
41
35
—
7
14
4
41
1/8
145.2
147.1
91.7
38.4
72.6
110
33.8
1.5
50
40
—
9
18
5
48
1/8
155.2
149.1
93.2
38.4
77.6
110
33.8
1.2
50
40
—
9
18
5
48
1/8
191.2
220.1
175.5
—
93.1
110
43.3
3.2
70
50
—
11
20
6
60
1/8
196.2
234.1
175.5
—
98.1
110
43.3
3.2
70
50
—
11
20
6
60
Optional specifications
Square type
pressure gauge
Digital pressure
switch
AF AR AL
AC20A-B
AF AFM AR
AC10A-A
Applicable model
Optional/Semi-standard
With auto drain
specifications
Centre of
piping
Attachment
Centre of
piping
Semi-standard specifications
Round type
Round type
pressure gauge
pressure gauge
(with colour zone)
With
auto
drain
With
barb
fitting
With
drain
guide
Metal
bowl
Metal bowl Metal bowl Metal bowl with
with drain with level level gauge, with
drain guide
guide
gauge
H
J
H
J
H
J
H
J
B
B
B
B
B
B
B
—
—
—
—
ø26
26
—
—
77.9
—
—
59.3
—
—
—
첸28
27
첸27.8
37.5
ø37.5
62.5
ø37.5
63.5
104.9
—
91.4
87.4
93.9
—
—
첸28
30
첸27.8
40.9
ø37.5
66.9
ø37.5
67.9
156.8
123.6
121.9
117.6
122.1
137.6
142.1
첸28
38.4
첸27.8
48.8
ø42.5
75.7
ø42.5
75.7
186.9
155.6
153.9
149.6
154.1
169.6
174.1
첸28
38.4
첸27.8
48.8
ø42.5
75.7
ø42.5
75.7
188.9
157.6
155.9
151.6
156.1
171.6
176.1
첸28
44.3
첸27.8
61.3
ø42.5
80.8
ø42.5
80.8
259.9
228.6
226.9
222.6
227.1
242.6
247.1
첸28
44.3
첸27.8
61.3
ø42.5
80.8
ø42.5
80.8
273.9
242.6
240.9
236.6
241.1
256.6
261.1
AW
Note) The dimension of C is the length when the filter regulator knob is unlocked.
AFM / AFD
H
H
Centre of
piping
Dimensions
J
AW AL
Round type pressure gauge Round type pressure gauge (with colour zone)
J
AR
Digital pressure switch
J
AL
Square embedded type pressure gauge
H
Option
Series
AF
Air Combination
20
Air Combination
Air Filter + Regulator
Symbol
AC10B-A
1
L
How to Order
AC10B M5
A
q
w
e
Option
q
앬
Float type auto drain
C
Refer to page 23 for size 20 to 60.
• Option/Semi-standard: Select one each for a to g.
• Option/Semi-standard symbol: When more than one specification is
required, indicate in alphanumeric order.
Example) AC10B-M5CG-T-12NR-A
Symbol
a
2
Description
—
Without auto drain
Note 1)
N.C. (Normally closed) Drain port is closed when pressure is not applied.
+
b
Pressure gauge
G
—
Without pressure gauge
Note 2)
Round type pressure gauge (without limit indicator)
+
w
앬
Attachment (T-spacer) Note 3)
—
Without attachment
T
Mounting position: AF+T+AR
+
c
Set pressure Note 4)
—
0.05 to 0.7 MPa setting
1
0.02 to 0.2 MPa setting
+
e
앬
Semi-standard
d
Bowl Note 5)
—
Polycarbonate bowl
2
Metal bowl
6
Nylon bowl
+
e
Exhaust mechanism
—
Relieving type
N
Non-relieving type
+
f
Flow direction
—
Flow direction: Left to right
R
Flow direction: Right to left
+
g
Pressure unit
—
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Z
Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
Note 1) When pressure is not applied, condensate which does not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending operations for the day is recommended.
Note 2) A 1.0 MPa pressure gauge will be fitted. It is not assembled and supplied loose at the time of shipment.
Note 3) The bracket position varies depending on the T-spacer mounting.
Note 4) Pressure can be set higher than the specification pressure in some cases, but use pressure within the specification range.
Note 5) Refer to Chemical data on page 46 for chemical resistance of the bowl.
21
Series AC10B-A
AC
Air Combination
AF AR AL
AC10B-A
Air Filter [AF]
AF10-A
Regulator [AR]
AR10-A
Air
Proof pressure
1.5 MPa
Maximum operating pressure
1.0 MPa
0.05 to 0.7 MPa
Bowl material [AF]
Polycarbonate
Construction [AR]
Relieving type
Weight [kg]
AF AFM AR
5 μm
0.16
AW AFM
Nominal filtration rating [AF]
Attachment
Set pressure range [AR]
AF AR
–5 to 60°C (with no freezing)
AF
Ambient and fluid temperature
1/16
AFM / AFD
Fluid
M5 x 0.8
AR
Pressure gauge port size [AR]
AL
Port size
AW
Component
AW AL
Standard Specifications
22
Air Combination
Air Filter + Regulator
Symbol
AC20B-B to AC60B-B
q
B
03 DE
w
e
r
t
y
2
L
Refer to page 21 for size 10.
How to Order
AC 30 B
1
• Option/Semi-standard: Select one each for a to j.
• Option/Attachment/Semi-standard symbol: When more than one
specification is required, indicate in alphanumeric order.
Example) AC30B-F03DE1-SV-16NR-B
q
앬
Symbol
Description
Body size
20
w
앬
Pipe thread type
—
N Note 1)
F Note 2)
Port size
01
02
03
04
06
10
25
30
40
—
—
—
50
55
60
Rc
NPT
G
+
e
앬
1/8
1/4
3/8
1/2
3/4
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
+
a
Float type
auto drain
Without auto drain
—
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
—
r
앬
Option Note 3)
+
Pressure
gauge Note 6)
b
Digital
pressure
switch
—
E
G
M
E1
E2
E3
E4
Without pressure gauge
Square embedded type pressure gauge (with limit indicator)
Round type pressure gauge (with limit indicator)
Round type pressure gauge (with colour zone)
Output: NPN output/Electrical entry: Wiring bottom entry
Output: NPN output/Electrical entry: Wiring top entry
Output: PNP output/Electrical entry: Wiring bottom entry
Output: PNP output/Electrical entry: Wiring top entry
t
앬
Attachment
+
c
Pressure
switch
T-spacer
—
Without attachment
S Note 7) Mounting position: AF+S+AR
T Note 7) Mounting position: AF+T+AR
+
Without attachment
—
Pressure relief
d
V
Mounting position: AF+AR+V
3 port valve
V1 Note 8) Mounting position: V+AF+AR쏔K
+
e
Set
pressure Note 9)
—
1
Bowl Note 10)
—
2
6
8
C
6C
0.05 to 0.85 MPa setting
0.02 to 0.2 MPa setting
y
앬
Semi-standard
+
f
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
Nylon bowl with bowl guard
—
— Note 11) — Note 11) — Note 11) — Note 11) — Note 11) — Note 11)
— Note 12) — Note 12) — Note 12) — Note 12) — Note 12) — Note 12)
+
—
With drain cock
Drain guide 1/8
Air filter
Note 14)
g
J
drain port Note 13)
Drain guide 1/4
W Note 15) Drain cock with barb fitting: For ø6 x ø4 nylon tube
23
—
—
—
—
—
—
—
—
Series
AC20B-B to AC60B-B
AC20B-B
AC40B-B
q
앬
Description
Body size
20
Flow direction
—
R
50
55
60
Relieving type
Non-relieving type
i
AF AR
+
Flow direction: Left to right
Flow direction: Right to left
+
—
j
Pressure unit
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Z Note 16) Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
ZA Note 17) Digital pressure switch: With unit conversion function
Note 1) Drain guide is NPT1/8 (applicable to the AC20B-B)
and NPT1/4 (applicable to the AC25B-B to
AC60B-B).
The auto drain port comes with ø3/8" One-touch
fitting (applicable to the AC25B-B to AC60B-B).
Note 2) Drain guide is G1/8 (applicable to the AC20B-B)
and G1/4 (applicable to the AC25B-B to AC60B-B).
Note 3) Option G, M are not assembled and supplied loose
at the time of shipment.
Note 4) When pressure is not applied, condensate which
does not start the auto drain mechanism will be left
in the bowl. Releasing the residual condensate
before ending operations for the day is
recommended.
Note 5) If the compressor is small (0.75 kW, discharge flow
is less than 100 L/min[ANR]), air leakage from the
drain cock may occur during start of operations.
N.C. type is recommended.
Note 6) When the pressure gauge is attached, a 1.0 MPa
pressure gauge will be fitted for standard (0.85
MPa) type. 0.4 MPa pressure gauge for 0.2 MPa
type.
Note 7) The bracket position varies depending on the
T-spacer or pressure switch mounting.
Note 8) Make sure that the outlet pressure is released to
atmospheric pressure using a pressure gauge.
Note 9) Pressure can be set higher than the specification
pressure in some cases, but use pressure within
the specification range.
Note 10) Refer to Chemical data on page 46 for chemical
resistance of the bowl.
Note 11) A bowl guard is provided as standard equipment
(polycarbonate).
Note 12) A bowl guard is provided as standard equipment
(nylon).
Note 13) The combination of float type auto drain: C and D
Note 18)
Note 18)
Note 18)
Note 18)
Note 18)
Note 18)
Note 18)
Note 19)
Note 19)
Note 19)
Note 19)
Note 19)
Note 19)
Note 19)
is not available.
Note 14) Without a valve function
Note 15) The combination of metal bowl: 2 and 8 is not
available.
Note 16) For pipe thread type: NPT.
Cannot be used with M: Round pressure gauge
(with colour zone). Available by request for
special.
The digital pressure switch will be equipped with
the unit conversion function, setting to psi initially.
Note 17) For options: E1, E2, E3, E4.
Note 18) 쑗: For pipe thread type: NPT only
Note 19) 왕: Select with options: E1, E2, E3, E4.
Standard Specifications
1/4, 3/8
0.53
AC40B-B AC40B-06-B AC50B-B
AF40-A AF40-06-A AF50-A
AR40-B AR40-06-B AR50-B
1/4, 3/8, 1/2
3/4
3/4, 1
1/8
Air
–5 to 60°C (with no freezing)
1.5 MPa
1.0 MPa
0.05 to 0.85 MPa
5 μm
Polycarbonate
Standard (Polycarbonate)
Relieving type
0.91
0.99
2.27
AC55B-B
AF60-A
AR50-B
AC60B-B
AF60-A
AR60-B
1
1
2.40
2.45
AFM / AFD
AC30B-B
AF30-A
AR30-B
AR
Model
AC20B-B AC25B-B
Air Filter [AF]
AF20-A
AF30-A
Component
Regulator [AR]
AR20-B
AR25-B
Port size
1/8, 1/4
1/4, 3/8
Pressure gauge port size [AR] Note 1)
Fluid
Ambient and fluid temperature Note 2)
Proof pressure
Maximum operating pressure
Set pressure range [AR]
Nominal filtration rating [AF]
Bowl material [AF]
Semi-standard (Steel)
Bowl guard [AF]
Construction [AR]
Weight [kg]
0.27
0.45
AF AFM AR
—
N
40
AW AFM
Exhaust
mechanism
30
Attachment
y
앬
Semi-standard
h
25
AF
Symbol
AW AL
AF AR AL
AC
Air Combination
AW
AL
Note 1) Pressure gauge connection threads are not available for F.R.L. unit with a square embedded type pressure gauge or with a digital pressure switch.
Note 2) –5 to 50°C for the products with the digital pressure switch
24
AC10B-A
Series AC20B-B to AC60B-B
Series
Dimensions
AC10B-A
A
F
S
M
OUT
B
Q1
Q2
IN
C
Q1
V
P2
(Pressure gauge port size)
R
J
2 x P1
(Port size)
G
Clearance for
maintenance
U
Drain
AC20B-B
A
F
P2
M
S
(Pressure gauge port size)
C
IN
OUT
2 x P1
(Port size)
B
Q1
Q2
K
Q1
V
R
J
G
Clearance for
maintenance
U
Drain
AC25B-B to AC60B-B
A
F
P2
S
M
(Pressure gauge port size)
K
C
Q1
V
R
F
OUT
Q1
IN
2 x P1
(Port size)
G
E
25
Clearance for
maintenance
B
U
Drain
AC10B-A
Air Combination Series AC20B-B to AC60B-B
With auto drain
Metal bowl
With drain guide
Metal bowl with drain guide
With auto drain (N.O./N.C.)
1/8
Width across
flats 14
AF AR
B
B
Width across
flats 14
M5 x 0.8
Thread type/Rc, G:
ø10 One-touch fitting
Thread type/NPT:
ø3/8" One-touch fitting
1/8
AC25B-B to AC60B-B
Metal bowl with level gauge,
with drain guide
Drain cock with barb fitting
B
Dimensions
Width across
flats 17
Width across
flats 17
1/4
Width across
flats 17
1/4
AW AFM
B
With drain guide
B
Metal bowl
with level gauge
B
Metal bowl with drain guide
B
Metal bowl
B
Applicable model
Optional/Semi-standard
specifications
AC25B-B to AC60B-B
N.O.: Black
N.C.: Grey
B
B
Metal bowl
B
Dimensions
AC
AC20B-B
Barb fitting
applicable
tubing: T0604
1/4
Standard specifications
Model
P1
M5 x 0.8
AC10B-A
1/8, 1/4
AC20B-B
1/4, 3/8
AC25B-B
1/4, 3/8
AC30B-B
1/4, 3/8, 1/2
AC40B-B
3/4
AC40B-06-B
3/4, 1
AC50B-B
1
AC55B-B
1
AC60B-B
P2
A
B
C
E
F
G
J
K
1/16
56
59.9
11
—
28
25
12.5
—
26.5
—
Bracket mount
M
Q1
Q2
R
S
U
25
20
27
4.5
6.8
3
83.2
87.6
41.6
25
28.5
2 Note)
30
24
33
5.5
12
3.5
29
1/8
110.2
115.1
28
30
55.1
35
27.5
0
41
35
—
7
14
4
41
1/8
110.2
115.1
30.7
30
55.1
35
29.4
3.5
41
35
—
7
14
4
41
1/8
145.2
147.1
35.8
38.4
72.6
40
33.8
3.5
50
40
—
9
18
5
48
1/8
155.2
149.1
35.8
38.4
77.6
40
33.8
3
50
40
—
9
18
5
48
1/8
186.2
220.1
43
—
93.1
30
43.3
3.2
70
50
—
11
20
6
60
1/8
191.2
234.1
43
—
98.1
30
43.3
3.2
70
50
—
11
20
6
60
1/8
196.2
234.1
46
—
98.1
30
43.3
3.2
70
50
—
11
20
6
60
Digital pressure
switch
With
auto
drain
With
barb
fitting
With
drain
guide
Metal
bowl
Metal bowl Metal bowl Metal bowl with
level gauge,
with drain with level
with drain guide
guide
gauge
H
J
H
J
H
J
H
J
B
B
B
B
B
B
B
—
—
—
—
ø26
26
—
—
77.9
—
—
59.3
—
—
—
첸28
29.5
첸27.8
40
ø37.5
65
ø37.5
66
104.9
—
91.4
87.4
93.9
—
—
첸28
28.5
첸27.8
39
ø37.5
64
ø37.5
65
156.8
123.6
121.9
117.6
122.1
137.6
142.1
첸28
30.4
첸27.8
40.9
ø37.5
65.9
ø37.5
66.9
156.8
123.6
121.9
117.6
122.1
137.6
142.1
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
186.9
155.6
153.9
149.6
154.1
169.6
174.1
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
188.9
157.6
155.9
151.6
156.1
171.6
176.1
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
259.9
228.6
226.9
222.6
227.1
242.6
247.1
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
273.9
242.6
240.9
236.6
241.1
256.6
261.1
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
273.9
242.6
240.9
236.6
241.1
256.6
261.1
AR
AC10B-A
AC20B-B
AC25B-B
AC30B-B
AC40B-B
AC40B-06-B
AC50B-B
AC55B-B
AC60B-B
Square type
pressure gauge
Semi-standard specifications
Round type
Round type
pressure gauge
pressure gauge
(with colour zone)
AW
Model
V
24.5
1/8
Optional specifications
AF AFM AR
AC10B-A
Applicable model
Optional/Semi-standard
With auto drain
specifications
Centre of
piping
Attachment
Centre of
piping
AF
H
H
H
Centre of
piping
Dimensions
AF AR AL
J
AW AL
Round type pressure gauge Round type pressure gauge (with colour zone)
J
AFM / AFD
Digital pressure switch
J
B
Square embedded type pressure gauge
B
Option
Series
AL
Air Combination
Note) For the AC20B-B only, the position of the pressure gauge is above the centre of the piping.
26
Air Combination
Air Filter + Mist Separator + Regulator
AC20C-B to AC40C-B
Symbol
1
2
L
L
How to Order
AC 30 C
q
B
03 DE
w
e
r
t
Symbol
y
• Option/Semi-standard: Select one each for a to j.
• Option/Attachment/Semi-standard symbol: When more than one
specification is required, indicate in alphanumeric order.
Example) AC30C-F03DE1-SV-16NR-B
Description
Body size
20
Pipe thread type
—
N Note 1)
F Note 2)
Port size
01
02
03
04
06
25
30
40
—
—
—
—
—
—
—
—
—
— Note 11)
— Note 11)
— Note 11)
— Note 12)
— Note 12)
— Note 12)
—
—
—
Rc
NPT
G
+
1/8
1/4
3/8
1/2
3/4
—
+
a
Float type
auto drain
Without auto drain
—
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
—
Option Note 3)
+
Pressure
gauge Note 6)
b
Digital
pressure
switch
—
E
G
M
E1
E2
E3
E4
Without pressure gauge
Square embedded type pressure gauge (with limit indicator)
Round type pressure gauge (with limit indicator)
Round type pressure gauge (with colour zone)
Output: NPN output/Electrical entry: Wiring bottom entry
Output: NPN output/Electrical entry: Wiring top entry
Output: PNP output/Electrical entry: Wiring bottom entry
Output: PNP output/Electrical entry: Wiring top entry
Attachment
+
c
Pressure
switch
T-spacer
—
Without attachment
S Note 7) Mounting position: AF+AFM+S+AR
T Note 7) Mounting position: AF+AFM+T+AR
+
Without attachment
—
Pressure relief
d
V
Mounting position: AF+AFM+AR+V
3 port valve
V1 Note 8) Mounting position: V+AF+AFM+AR쏔K
+
e
Set
pressure Note 9)
—
1
Bowl Note 10)
—
2
6
8
C
6C
0.05 to 0.85 MPa setting
0.02 to 0.2 MPa setting
Semi-standard
+
f
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
Nylon bowl with bowl guard
+
—
With drain cock
Air filter
Drain guide 1/8
Note 14)
g Mist separator J
Drain guide 1/4
drain port Note 13)
W Note 15) Drain cock with barb fitting: For ø6 x ø4 nylon tube
+
h
27
—
Exhaust
mechanism
—
N
Relieving type
Non-relieving type
—
—
Series
AC20C-B to AC40C-B
AC20C-B
AF AR AL
AC
Air Combination
AC40C-B
q
앬
Flow direction
—
R
Body size
20
25
30
40
Note 18)
Note 18)
Note 18)
Note 18)
Note 19)
Note 19)
Note 19)
Note 19)
AW AL
i
Description
Flow direction: Left to right
Flow direction: Right to left
Note 1) Drain guide is NPT1/8 (applicable to the
AC20C-B) and NPT1/4 (applicable to the
AC25C-B to AC60C-B).
The auto drain port comes with ø3/8" One-touch
fitting (applicable to the AC25C-B to AC60C-B).
Note 2) Drain guide is G1/8 (applicable to the AC20C-B)
and G1/4 (applicable to the AC25C-B to AC60C-B).
Note 3) Option G, M are not assembled and supplied
loose at the time of shipment.
Note 4) When pressure is not applied, condensate which
does not start the auto drain mechanism will be
left in the bowl. Releasing the residual
condensate before ending operations for the day
is recommended.
Note 5) If the compressor is small (0.75 kW, discharge
flow is less than 100 L/min [ANR]), air leakage
from the drain cock may occur during start of
operations. N.C. type is recommended.
Note 6) When the pressure gauge is attached, a 1.0 MPa
pressure gauge will be fitted for standard (0.85 MPa)
type. 0.4 MPa pressure gauge for 0.2 MPa type.
Note 7) The bracket position varies depending on the
T-spacer or pressure switch mounting.
Note 8) Make sure that the outlet pressure is released to
atmospheric pressure using a pressure gauge.
Note 9) Pressure can be set higher than the specification
pressure in some cases, but use pressure within
the specification range.
Note 10) Refer to Chemical data on page 46 for chemical
resistance of the bowl.
Note 11) A bowl guard is provided as standard equipment
(polycarbonate).
Note 12) A bowl guard is provided as standard equipment
(nylon).
Note 13) The combination of float type auto drain: C and
D is not available.
Note 14) Without a valve function
Note 15) The combination of metal bowl: 2 and 8 is not
available.
Note 16) For pipe thread type: NPT.
Cannot be used with M: Round pressure gauge
(with colour zone). Available by request for
special.
The digital pressure switch will be equipped
with the unit conversion function, setting to psi
initially.
Note 17) For options: E1, E2, E3, E4.
Note 18) 앪: For pipe thread type: NPT only
Note 19) 왕: Select with options: E1, E2, E3, E4.
Standard Specifications
AC20C-B
Air Filter [AF]
Component Mist Separator [AFM]
Regulator [AR]
Port size
AF30-A
AF30-A
AF40-A
AF40-06-A
AFM30-A
AFM30-A
AFM40-A
AFM40-06-A
AR20-B
AR25-B
AR30-B
AR40-B
AR40-06-B
1/8, 1/4
1/4, 3/8
1/4, 3/8
1/4, 3/8, 1/2
3/4
Note 1)
1/8
−5 to 60°C (with no freezing)
Maximum operating pressure
1.0 MPa
Set pressure range [AR]
0.05 to 0.85 MPa
AF: 5 µm, AFM: 0.3 µm (99.9% filtered particle size)
200
450
Outlet side oil mist concentration [AFM] Note 4) Note 5)
450
1100
AR
Nominal filtration rating [AF/AFM]
Rated flow (L/min(ANR)) [AFM] Note 3)
AFM / AFD
Air
Note 2)
1.5 MPa
1100
Max.1.0 mg/m3 (ANR) (≈0.8 ppm)
Bowl material [AF/AFM]
Polycarbonate
Semi-standard (Steel)
Standard (Polycarbonate)
Construction [AR]
Weight [kg]
AC40C-06-B
AF20-A
Proof pressure
Bowl guard [AF/AFM]
AC40C-B
AFM20-A
Fluid
Ambient and fluid temperature
AC30C-B
AL
Pressure gauge port size [AR]
AC25C-B
AF
Model
AF AFM AR
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Pressure unit Z Note 16) Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
ZA Note 17) Digital pressure switch: With unit conversion function
AW AFM
j
AF AR
+
—
Attachment
y
앬
Semi-standard
Symbol
Relieving type
0.38
0.69
0.77
1.39
1.53
AW
Note 1) Pressure gauge connection threads are not available for F.R.L. unit with a square embedded type pressure gauge or with a digital pressure switch.
Note 2) −5 to 50°C for the products with the digital pressure switch
Note 3) Conditions: Mist separator inlet pressure: 0.7 MPa; The rated flow varies depending on the inlet pressure.
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side.
Note 4) When the compressor oil mist discharge concentration is 30 mg/m3 (ANR).
Note 5) Bowl seal and other O-rings are slightly lubricated.
28
Series
AC20C-B to AC40C-B
Dimensions
AC20C-B
AC25C-B to AC40C-06-B
A
N
M
IN
OUT
Q1
B
P2
(Pressure gauge port size)
E
G
Square embedded type pressure gauge
Digital pressure switch
B
H
H
H
Centre of
piping
Centre of
piping
AC20C-B
AC25C-B to AC40C-06-B
Metal bowl
With drain guide
Width across
flats 14
M5 x 0.8
Metal bowl with drain guide
With auto drain (N.O./N.C.)
N.O.: Black
N.C.: Grey
B
B
B
Dimensions
(Pressure gauge port size)
J
Applicable model
With auto drain (N.C.)
P2
Drain
Round type pressure gauge Round type pressure gauge (with colour zone)
J
Centre of
piping
Drain
Width across
flats 14
1/8
B
Drain
2 x P1
(Port size)
Clearance for
maintenance
Clearance for
maintenance
Drain
Dimensions
Thread type/Rc, G: ø10 One-touch fitting
Thread type/NPT: ø3/8" One-touch fitting
1/8
AC25C-B to AC40C-06-B
With drain guide
Drain cock with barb fitting
B
B
B
B
Metal bowl with drain guide Metal bowl with level gauge Metal bowl with level gauge, with drain guide
B
Metal bowl
B
Applicable model
Optional/Semi-standard specifications
OUT
U
J
Optional/Semi-standard specifications
C
IN
B
Option
G
U
2 x P1
(Port size)
S
Q1
V
K
C
R
Q1
V
M
S
Q1
Q2
K
J
R
F
J
A
N
F
Dimensions
Width across
flats 17
Width across
flats 17
1/4
1/4
Width across
flats 17
Barb fitting
applicable
tubing: T0604
1/4
Standard specifications
Model
P1
1/8, 1/4
AC20C-B
1/4, 3/8
AC25C-B
1/4, 3/8
AC30C-B
AC40C-B 1/4, 3/8, 1/2
3/4
AC40C-06-B
Bracket mount
P2
A
B
C
E
F
G
J
K
1/8
126.4
87.6
26.5
—
41.6
40
28.5
2 Note)
1/8
167.4
115.1
28
30
55.1
50
27.5
0
41
57.2
35
—
7
14
4
41
1/8
167.4
115.1
30.7
30
55.1
50
29.4
3.5
41
57.2
35
—
7
14
4
41
1/8
220.4
147.1
35.8
38.4
72.6
75
33.8
3.5
50
75.2
40
—
9
18
5
48
1/8
235.4
149.1
35.8
38.4
77.6
75
33.8
3
50
80.2
40
—
9
18
5
48
M
N
Q1
Q2
R
S
U
V
30
43.2
24
33
5.5
12
3.5
29
Optional specifications
Model
AC20C-B
AC25C-B
AC30C-B
AC40C-B
AC40C-06-B
Square type
pressure gauge
Digital pressure
switch
J
Semi-standard specifications
Round type
Round type
pressure gauge
pressure gauge
(with colour zone)
H
J
H
J
With
barb
fitting
With
drain
guide
Metal
bowl
Metal bowl Metal bowl Metal bowl with
level gauge,
with drain with level
with drain guide
guide
gauge
H
J
H
B
B
B
B
B
B
B
첸28
29.5
첸27.8
40
ø37.5
65
ø37.5
66
104.9
—
91.4
87.4
93.9
—
—
첸28
28.5
첸27.8
39
ø37.5
64
ø37.5
65
156.8
123.6
121.9
117.6
122.1
137.6
142.1
첸28
30.4
첸27.8
40.9
ø37.5
65.9
ø37.5
66.9
156.8
123.6
121.9
117.6
122.1
137.6
142.1
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
186.9
155.6
153.9
149.6
154.1
169.6
174.1
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
188.9
157.6
155.9
151.6
156.1
171.6
176.1
Note) For the AC20C-B only, the position of the pressure gauge is above the centre of the piping.
29
With
auto
drain
30
AW
AL
AR
AFM / AFD
AF
Attachment
AW AFM
AF AFM AR
AF AR
AW AL
AF AR AL
AC
Air Combination
Filter Regulator + Mist Separator
AC20D-B to AC40D-B
Symbol
1
L
How to Order
AC 30 D
q
03 DE
w
e
r
B
t
Symbol
y
—
N Note 1)
F Note 2)
Port size
01
02
03
04
06
L
• Option/Semi-standard: Select one each for a to j.
• Option/Attachment/Semi-standard symbol: When more than one
specification is required, indicate in alphanumeric order.
Example) AC30D-F03DE1-SV-16NR-B
Description
Body size
20
Pipe thread type
2
30
40
—
—
Rc
NPT
G
+
1/8
1/4
3/8
1/2
3/4
—
—
—
—
—
+
a
Float type
auto drain
— Without auto drain
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
—
Option Note 3)
+
Pressure
gauge Note 6)
b
Digital
pressure
switch
—
E
G
M
E1
E2
E3
E4
Without pressure gauge
Square embedded type pressure gauge (with limit indicator)
Round type pressure gauge (with limit indicator)
Round type pressure gauge (with colour zone)
Output: NPN output/Electrical entry: Wiring bottom entry
Output: NPN output/Electrical entry: Wiring top entry
Output: PNP output/Electrical entry: Wiring bottom entry
Output: PNP output/Electrical entry: Wiring top entry
Attachment
+
c
Pressure
switch
—
Without attachment
S Note 7) Mounting position: AW+S+AFM
+
— Without attachment
Pressure relief
d
V
Mounting position: AW+AFM+V
3 port valve
V1 Note 8) Mounting position: V+AW쏔K+AFM
+
e
Set
pressure Note 9)
—
1
Bowl Note 10)
—
2
6
8
C
6C
0.05 to 0.85 MPa setting
0.02 to 0.2 MPa setting
+
y
Semi-standard
f
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
Nylon bowl with bowl guard
— Note 11)
— Note 11)
— Note 12)
— Note 12)
—
—
+
— With drain cock
Filter regulator
Drain guide 1/8
Note 14)
g Mist separator J
Drain guide 1/4
drain port Note 13)
W Note 15) Drain cock with barb fitting: For ø6 x ø4 nylon tube
+
h
Exhaust
mechanism
—
N
Flow direction
—
R
Relieving type
Non-relieving type
+
i
31
—
Flow direction: Left to right
Flow direction: Right to left
—
—
Series AC20D-B
to AC40D-B
AC20D-B
AF AR AL
AC
Air Combination
AC40D-B
q
앬
Note 1) Drain guide is NPT1/8 (applicable to the AC20D-B)
and NPT1/4 (applicable to the AC30D-B/AC40D-B).
The auto drain port comes with ø3/8" One-touch
fitting (applicable to the AC30D-B/AC40D-B).
Note 2) Drain guide is G1/8 (applicable to the AC20D-B)
and G1/4 (applicable to the AC30D-B/AC40D-B).
Note 3) Option G, M are not assembled and supplied loose
at the time of shipment.
Note 4) When pressure is not applied, condensate which
does not start the auto drain mechanism will be left
in the bowl. Releasing the residual condensate
before ending operations for the day is
recommended.
Note 5) If the compressor is small (0.75 kW, discharge flow
is less than 100 L/min [ANR]), air leakage from the
drain cock may occur during start of operations.
N.C. type is recommended.
Note 6) When the pressure gauge is attached, a 1.0 MPa
pressure gauge will be fitted for standard (0.85 MPa)
type. 0.4 MPa pressure gauge for 0.2 MPa type.
Note 7) The bracket position varies depending on the
pressure switch mounting.
Note 8) Make sure that the outlet pressure is released to
atmospheric pressure using a pressure gauge.
Note 9) Pressure can be set higher than the specification
pressure in some cases, but use pressure within
the specification range.
Note 10) Refer to Chemical data on page 46 for chemical
resistance of the bowl.
Note 11) A bowl guard is provided as standard equipment
(polycarbonate).
Note 12) A bowl guard is provided as standard equipment
(nylon).
Note 13) The combination of float type auto drain: C and D
30
40
Note 18)
Note 18)
Note 18)
Note 19)
Note 19)
Note 19)
is not available.
Note 14) Without a valve function
Note 15) The combination of metal bowl: 2 and 8 is not
available.
Note 16) For pipe thread type: NPT.
Cannot be used with M: Round pressure gauge
(with colour zone). Available by request for
special.
The digital pressure switch will be equipped with
the unit conversion function, setting to psi initially.
Note 17) For options: E1, E2, E3, E4.
Note 18) 앪: For pipe thread type: NPT only
Note 19) 왕: Select with options: E1, E2, E3, E4.
Standard Specifications
AC40D-B
Filter Regulator [AW]
AW20-B
AW30-B
AW40-B
AW40-06-B
Mist Separator [AFM]
AFM20-A
AFM30-A
AFM40-A
AFM40-06-A
1/8, 1/4
1/4, 3/8
1/4, 3/8, 1/2
3/4
Port size
Pressure gauge port size [AW] Note 1)
1/8
Fluid
Air
Ambient and fluid temperature Note 2)
1.5 MPa
Maximum operating pressure
1.0 MPa
0.05 to 0.85 MPa
Nominal filtration rating [AW/AFM]
Rated flow (L/min(ANR)) [AFM] Note 3)
AW: 5 µm, AFM: 0.3 µm (99.9% filtered particle size)
150
Note 4) Note 5)
330
800
800
3
Max.1.0 mg/m (ANR) (≈0.8 ppm)
Bowl material [AW/AFM]
Bowl guard [AW/AFM]
AFM / AFD
Set pressure range [AW]
Outlet side oil mist concentration [AFM]
AF
−5 to 60°C (with no freezing)
Proof pressure
Polycarbonate
Semi-standard (Steel)
Standard (Polycarbonate)
Construction [AW]
Weight [kg]
AC40D-06-B
AR
Component
AC30D-B
Attachment
AC20D-B
Model
AF AR
— Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Pressure unit Z Note 16) Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
ZA Note 17) Digital pressure switch: With unit conversion function
20
AW AL
Body size
AF AFM AR
j
Description
AW AFM
y
앬
Semi-standard
Symbol
Relieving type
0.32
0.62
1.15
1.25
AW
AL
Note 1) Pressure gauge connection threads are not available for F.R.L. unit with a square embedded type pressure gauge or with a digital pressure switch.
Note 2) −5 to 50°C for the products with the digital pressure switch
Note 3) Conditions: Mist separator inlet pressure: 0.5 MPa; The rated flow varies depending on the inlet pressure.
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side.
Note 4) When the compressor oil mist discharge concentration is 30 mg/m3 (ANR).
Note 5) Bowl seal and other O-rings are slightly lubricated.
32
Series AC20D-B
to AC40D-B
Dimensions
AC20D-B
AC30D-B to AC40D-06-B
A
J
F
M
M
S
C
R
Q1
V
Q1
V
IN
IN
OUT
2 x P1
(Port size)
B
U
Drain
E
Digital pressure switch
Centre of
piping
Centre of
piping
AC30D-B to AC40D-06-B
B
B
B
Width across
flats 14
M5 x 0.8
Metal bowl with drain guide
With auto drain (N.O./N.C.)
N.O.: Black
N.C.: Grey
B
Metal bowl
With drain guide
Dimensions
Width across
flats 14
1/8
Thread type/Rc, G: ø10 One-touch fitting
Thread type/NPT: ø3/8" One-touch fitting
1/8
AC30D-B to AC40D-06-B
Metal bowl with level gauge,
with drain guide
B
B
With drain guide
Drain cock with barb fitting
Dimensions
Width across
flats 17
Width across
flats 17
1/4
Width across
flats 17
1/4
B
Metal bowl
with level gauge
B
Metal bowl with drain guide
B
Metal bowl
B
Applicable model
Optional/Semi-standard
specification
Round type pressure gauge (with colour zone)
AC20D-B
Applicable model
With auto drain (N.C.)
Drain
Drain
J
H
H
Centre of
piping
Dimensions
Optional/Semi-standard
specification
Round type pressure gauge
J
J
P2
(Pressure gauge
port size)
B
Square embedded type pressure gauge
G
(Pressure gauge port size)
Clearance for
maintenance
Drain
P2
H
G
Option
Clearance for
maintenance
B
U
OUT
Q1
Q1
Q2
K
2 x P1
(Port size)
R
S
C
J
A
F
Barb fitting
applicable
tubing: T0604
1/4
Standard specifications
Model
P1
1/8, 1/4
AC20D-B
1/4, 3/8
AC30D-B
1/4, 3/8, 1/2
AC40D-B
3/4
AC40D-06-B
P2
A
B
C
1/8
1/8
1/8
1/8
83.2
110.2
145.2
155.2
87.6
115.1
147.1
149.1
E
F
G
J
K
—
30
38.4
38.4
41.6
55.1
72.6
77.6
40
50
75
75
28.5
29.4
33.8
33.8
5
3.5
1.5
1.2
Note)
72.4
85.6
91.7
93.2
Bracket mount
M
Q1
Q2
R
S
U
V
30
41
50
50
24
35
40
40
33
—
—
—
5.5
7
9
9
12
14
18
18
3.5
4
5
5
29
41
48
48
Optional specifications
Model
AC20D-B
AC30D-B
AC40D-B
AC40D-06-B
Square type
pressure gauge
Digital pressure
switch
Round type
pressure gauge
Semi-standard specifications
Round type
pressure gauge
(with colour zone)
With
barb
fitting
With
drain
guide
Metal
bowl
Metal bowl Metal bowl Metal bowl with
level gauge,
with drain with level
with drain guide
guide
gauge
H
J
H
J
H
J
H
J
B
B
B
B
B
B
B
첸28
첸28
첸28
첸28
27
30
38.4
38.4
첸27.8
첸27.8
첸27.8
첸27.8
37.5
40.9
48.8
48.8
ø37.5
ø37.5
ø42.5
ø42.5
62.5
66.9
75.7
75.7
ø37.5
ø37.5
ø42.5
ø42.5
63.5
67.9
75.7
75.7
104.9
156.8
186.9
188.9
—
123.6
155.6
157.6
91.4
121.9
153.9
155.9
87.4
117.6
149.6
151.6
93.9
122.1
154.1
156.1
—
137.6
169.6
171.6
—
142.1
174.1
176.1
Note) The dimension of C is the length when the filter regulator knob is unlocked.
33
With
auto
drain
Air Combination
Series AC
G27-10-R1
G27-10-R1
—
—
—
—
G36-10-첸01
G36-4-첸01
G36-10-첸01-L
G36-4-첸01-L
Attachment
Round
type
AW AL
G46-10-첸01
G46-4-첸01
G46-10-첸01-L
G46-4-첸01-L
GC3-10AS [GC3P-010AS (Pressure gauge cover only)]
GC3-4AS [GC3P-010AS (Pressure gauge cover only)]
ISE35-N-25-MLA [ISE35-N-25-M (Switch body only)] Note 3)
ISE35-R-25-MLA [ISE35-R-25-M (Switch body only)] Note 3)
—
ISE35-N-65-MLA [ISE35-N-65-M (Switch body only)] Note 3)
ISE35-R-65-MLA [ISE35-R-65-M (Switch body only)] Note 3)
—
—
AD38-A
AD48-A
AD17-A
AD27-A
AD37-A
AD47-A
Y100-A
Y200-A
Y300-A
Y400-A
Y500-A
Y600-A
Y100T-A
Y200T-A
Y300T-A
Y400T-A
Y500T-A
Y600T-A
AKM2000-첸01-A
AKM3000-(첸01)-A
AKM4000-(첸02)-A
Check valve Note 5) Note 6)
—
—
—
—
—
(첸02)-A
첸02-A
첸03-A
—
IS10M-20-A
IS10M-30-A
IS10M-40-A
IS10M-50-A
IS10M-60-A
Pressure switch Note 6)
Y210-첸01-A
Y310-(첸01)-A
Y410-(첸02)-A Y510-(첸02)-A Y610-첸03-A
Y610-(첸03)-A
Y110-M5-A
T-spacer Note 5) Note 6)
(첸02)-A
(첸04)-A
첸02-A
첸03-A
첸03-A
첸04-A
첸02A
VHS20-첸01A
VHS30-첸02A
VHS50-첸06A
Pressure relief
—
VHS40-첸03A VHS40-첸06A
—
—
3 port valve Note 6)
첸02A
첸03A
첸10A
첸04A
첸02-A
첸01-A
첸02-A
E400-첸03-A
E600-첸06
E100-M5-A
E200-첸02-A
E300-첸03-A
Piping adapter Note 6)
E500-첸06-A
첸04-A
첸10
첸03-A
첸04-A
첸06-A
첸02-A
첸01-A
첸02-A
IS10E-40첸03-A
Pressure switch with
—
—
—
—
—
IS10E-20첸02-A
IS10E-30첸03-A
piping adapter Note 6)
첸04-A
첸03-A
첸04-A
첸06-A
Y24-첸01-A
Y34-첸01-A
Y44-첸02-A
Y54-첸03-A
Y14-M5-A
Cross spacer Note 6)
—
—
—
첸02-A
첸02-A
첸03-A
첸04-A
Note 1) 첸 in part numbers for a round pressure gauge indicates a pipe thread type. No
Regarding how to order the digital pressure switch, please consult with SMC.
indication is necessary for R; however, indicate N for NPT. Please contact
Note 4) Minimum operating pressure: N.O. type–0.1 MPa; N.C. type–0.1 MPa (AD27-A)
SMC regarding the connection thread NPT and pressure gauge supply for psi
and 0.15 MPa (AD37-A/AD47-A). Please consult with SMC separately for psi
unit specifications.
and °F unit display specifications.
Note 2) Including one O-ring and 2 mounting screws
Note 5) For F.R.L. units, port sizes without ( ) are standard specifications.
Note 3) Lead wire with connector (2 m), adapter, lock pin, O-ring (1 pc.), mounting
Note 6) Separate spacers are required for modular unit.
screw (2 pcs.) are attached. [ ]: Switch body only.
Option
Pressure gauge Note 1)
Standard
0.02 to 0.2 MPa setting
Round type
Standard
(with colour
0.02 to 0.2 MPa setting
zone)
Square
Standard
embedded
type Note 2) 0.02 to 0.2 MPa setting
NPN output/Wiring bottom entry
Digital
NPN output/Wiring top entry
pressure
PNP output/Wiring bottom entry
switch
PNP output/Wiring top entry
N.O.
Float type
auto drain Note 4)
N.C.
Spacer
Spacer with bracket
For AC40-06-B For AC50-B For AC55-B For AC60-B
—
For AC40A-06-B For AC50A-B
For AC60A-B
For AC40B-06-B For AC50B-B For AC55B-B For AC60B-B
—
—
—
For AC40C-06-B
—
—
—
For AC40D-06-B
AF AR
Type
For AC40-B
For AC40A-B
For AC40B-B
For AC40C-B
For AC40D-B
AF AFM AR
Model
For AC30-B
For AC30A-B
For AC30B-B
For AC30C-B
For AC30D-B
AW AFM
Section
Part no.
For AC10-A For AC20-B For AC25-B
—
For AC10A-A For AC20A-B
For AC10B-A For AC20B-B For AC25B-B
—
For AC20C-B For AC25C-B
—
—
For AC20D-B
Attachment
Options/Attachments/Part No.
AF AR AL
AC
Options/Attachments
Check Valve: (K) 1/8, 1/4, 3/8
AF
A check valve with intermediate air release port can be easily installed to prevent a backflow of lubricant when redirecting the air flow
and releasing the air on the outlet side of the regulator.
AKM 30 00
01 A
q
w
Body size
1/8
1/4
3/8
—
—
OUT
—
A
Specifications
Model
Effective area [mm2]
AKM2000-A
AKM3000-A
AKM4000-A
28
Be sure to use above check valves when
redirecting the air flow on the inlet side of
the lubricator. Threads for IN and OUT
ports are not machined.
D
55
111
AL
IN
+
Model
By-pass
port size
A
B
C
D
E
Applicable model
AKM2000-A 1/8, 1/4
40 28 11 40 11 AC20-B, AC20A-B
AKM3000-A 1/8, 1/4
53 34 14 48 13
AKM4000-A 1/4, 3/8
70 42 18 54 15 AC40-B, AC40A-BNote)
AC25-B
AC30-B, AC30A-B
Note) Cannot be mounted on the AC40쏔-06-B.
∗ Refer to the attachment table above for standard by-pass port
sizes applicable to the AC.
34
AW
01
02
03
Rc
NPT
G
B
e
By-pass
port size
40
By-pass port size for
redirecting air flow
C
Pipe thread
type
30
E
AR
20
w
Check valve
q
Symbol Description
—
N
F
e
AFM / AFD
Symbol
Series AC
Pressure Switch: (S)
A compact integrated pressure switch can be easily installed and facilitates the pressure detection of the line.
IS10M 30
A
q
Symbol
Pressure switch
w
• Semi-standard: Select one each for a to c.
• Semi-standard symbol: When more than one specification is required, indicate in alphanumeric order.
Example) IS10M-30-6LP
Symbol
Description
—
6 Note 1)
0.1 to 0.4 MPa
0.1 to 0.6 MPa
—
L
Z
0.5 m
3m
5m
q
앬
Body size
a
b
Lead wire
length
30
40
50
60
+
23
15
+
MPa
—
Pressure unit of
the scale plate
MPa/psi dual scale
P
Note 1) Set pressure range of 6P (L, Z) is 0.2 to 0.6 MPa (30 to 90 psi).
(23)
c
(5000)
(3000)
(500)
(13)
w
앬
Semi-standard
20
Set pressure
range
0.1
0.3
0.2
0.4
Specifications
MPa
Air
−5 to 60°C (with no freezing)
1.0 MPa
0.7 MPa
0.1 to 0.4 MPa
0.08 MPa or less
B
C
Fluid
Ambient and fluid temperature
Proof pressure
Maximum operating pressure
Set pressure range (when OFF)
Hysteresis
Centre of
F.R.L. body
D
Switch Characteristics
Contact point configuration
Maximum contact point capacity
Operating voltage: AC, DC
1a
2 VA (AC), 2 W (DC)
100 V or less
Maximum operating current
12 V to 24 VAC, DC: 50 mA
48 VAC, DC: 40 mA
100 VAC, DC: 20 mA
Note) For detailed specifications on the IS10 series, refer to the section of our
website IS10 series, http://www.smc.eu
A
Applicable model
A
B
C
D
10.6 74.2 64.4
28 AC20쏔-B
12.6 84.5 70.5
30 AC25쏔-B, AC30쏔-B
14.6 93.3 75.3
36 AC40쏔-B
16.6 97.3 77.3
44 AC40쏔-06-B
22
92.5 68.5
53 AC50쏔-B, AC55쏔-B, AC60쏔-B
∗ Separate spacers are required for modular unit.
Model
IS10M-20-A
IS10M-30-A
IS10M-40-A
IS10M-50-A
IS10M-60-A
T-Spacer: (T) M5 x 0.8, 1/8, 1/4, 3/8, 1/2
Using a T-spacer facilitates the branching of air flow.
E
Port size
B
C
Octagon
Centre of
F.R.L. body
D
A
T-spacer
Model Note)
Port size
A
Y110-M5-A
Y210-쏔01-A
Y210-쏔02-A
Y310-쏔01-A
Y310-쏔02-A
Y410-쏔02-A
Y410-쏔03-A
Y510-쏔02-A
Y510-쏔03-A
Y610-쏔03-A
Y610-쏔04-A
M5 x 0.8
11.2
19
12
14
14.6
41.8 32
28
19
AC20-B, AC20B-B
AC20C-B
14.6
52.7 38.7
30
19
AC25-B, AC25B-B
AC25C-B, AC30C-B
18.6
62
44
36
24
AC40-B, AC40B-B
AC40C-B
18.6
66
46
44
24
AC40-06-B, AC40B-06-B
AC40C-06-B
22
81
57
53
30
AC50-B, AC55-B, AC60-B,
AC50B-B, AC55B-B, AC60B-B
1/8
1/4
1/8
1/4
1/4
3/8
1/4
3/8
3/8
1/2
B
C
D
E
Applicable model
8 AC10-A, AC10B-A
Note) 쏔 in model numbers indicates a pipe thread type. No indication is necessary
for Rc; however, indicate N for NPT, and F for G.
∗ Separate interfaces are required for modular unit.
∗ Refer to the attachment table on page 34 for standard port sizes when using
with the AC.
Caution on Mounting
If a T-spacer is used on the inlet side of the lubricator, lubricant may
be mixed. Use the AKM series check valve to avoid such possibility.
35
Series AC
Attachments
Pressure Relief 3 Port Valve: (V)
03 A
r
AF AR AL
e
• Semi-standard: Select one each for a to b.
• Semi-standard symbol: When more than one specification is required,
indicate in alphanumeric order.
Example) VHS30-03A-RZ
Rc
NPT
G
20 30 40 50
N Note)
F Note)
Pipe thread type
SUP
A
w
앬
AW AL
—
q
앬
Body size
IN
OUT
+
—
—
—
—
—
—
—
—
—
—
—
—
3
(Port size)
Symbol
Flow direction: Left to right
Flow direction: Right to left
2
EXH.
b
2
3 1
— Name plate in imperial units: MPa
Z Note) Name plate in imperial units: psi
Pressure
unit
H
G
F
+
SUP.
Semi-standard
r
앬
—
R
Flow
direction
P2
EXH
—
+
a
2 x P1
(Port size)
B
—
ø10
Port size
1/8
1/4
3/8
1/2
3/4
1
øI
e
앬
01
02
03
04
06
10
AF AR
Description
AF AFM AR
Symbol
1
3
E
D
C
Specifications
Model
VHS20
VHS30
VHS40
VHS40-06
VHS50
IN, OUT EXH
1/8
1/4
1/4
3/8
1/4
3/8
1/2
3/4
3/4
1
1/8
1/4
3/8
1/2
1/2
IN 씮 OUT
C(dm3/s·bar)
b
2.4
0.43
3.3
0.40
6.4
0.45
8.3
0.41
7.3
0.49
10.9
0.45
14.2
0.39
18.3
0.31
23.8
0.41
31.9
0.33
Specifications
OUT 씮 EXH
Cv C(dm3/s·bar)
b
Cv
0.65
2.5
0.39 0.69
0.88
3.1
0.51 0.84
1.7
6.2
0.38 1.7
2.3
7.0
0.41 1.9
2.0
8.5
0.35 2.3
3.0
11.6
0.40 3.1
3.8
13.3
0.43 3.6
5.0
17.7
0.37 4.8
6.4
21.8
0.41 5.9
8.6
23.5
0.44 6.4
Key can be mounted when residual
pressure is released.
Standard specifications
Model
P1
1/8, 1/4
VHS20
1/4, 3/8
VHS30
VHS40 1/4, 3/8, 1/2
3/4
VHS40-06
3/4, 1
VHS50
P2
A
B
C
D
E
F
G
H
I
1/8
1/4
3/8
1/2
1/2
66.4
80.3
104.9
110.4
134.3
22.3
29.4
38.5
42
53
40
53
70
75
90
37.5
49
63
63
76
14
19
22
22
26
46.6
52
58
58
76
33.6
38
44
44
61
28
30
36
44
53
37.5
49
63
63
81
Note) Use an air filter on the inlet side
for operating protection.
AF
Port size
AW AFM
Note) For pipe thread type: NPT only.
Cross Spacer: M5 x 0.8, 1/8, 1/4, 3/8, 1/2
B
C
F
F
E
Port size
E
AFM / AFD
Centre of F.R.L. body
Pipings are possible in all 4 directions.
IN/OUT ports are not machined for threads.
Please contact SMC if threaded (machined) ports are required.
E
Cross spacer
Model Note)
Caution on Mounting
1. When mounting a cross spacer directly on the IN side of the lubricator, be
sure to use the AKM series check valve between the lubricator and cross
spacer.
2. Factory mounting of a cross spacer on the AC model is available as a
special order.
Y14-M5-A
Y24-쏔01-A
Y24-쏔02-A
Y34-쏔01-A
Y34-쏔02-A
Y44-쏔02-A
Y44-쏔03-A
Y54-쏔03-A
Y54-쏔04-A
E (Port size)
M5
1/8
1/4
1/8
1/4
1/4
3/8
3/8
1/2
E
D
A
AR
F: Without thread
Attachment
w
A
B
C
D
23
16
14
25
AC10쏔-A
40
40
22
40
AC20쏔-B
49
43
28
48
AC25쏔-B, AC30쏔-B
60
48
36
54
AC40쏔-B
72
62
40
62
AC40쏔-06-B
Applicable model
Note) 쏔 in model numbers indicates a pipe thread type. No indication is
necessary for Rc; however, indicate N for NPT, and F for G.
∗ If threaded IN/OUT ports are required, they are available as a special order.
Please contact SMC.
∗ Two hexagon socket head plugs are included in the package.
36
AL
q
AW
VHS 30
AC
Pressure relief
3 port valve
With the use of a pressure relief 3 port valve, pressure left in the line can be easily exhausted.
Series AC
Piping Adapter: M5 x 0.8, 1/8, 1/4, 3/8, 1/2, 3/4, 1
A piping adapter allows installation/removal of the component
without removing the piping and thus makes maintenance easier.
B
Port size
Centre of
F.R.L.
body
D
A
Piping adapter
Model Note)
Port size
A
B
D
E100-M5-A
E200-쏔01-A
E200-쏔02-A
E200-쏔03-A
E300-쏔02-A
E300-쏔03-A
E300-쏔04-A
E400-쏔02-A
E400-쏔03-A
E400-쏔04-A
E400-쏔06-A
E500-쏔06-A
M5 x 0.8
10
14
14
AC10쏔-A
29.8
23.5
28
AC20쏔-B
31.8
30
30
AC25쏔-B, AC30쏔-B
31.8
36
36
AC40쏔-B
31.8
40
44
AC40쏔-06-B
E600-쏔06-A
3/4
E600-쏔10-A
35
48
53
1
AC50-B, AC55-B, AC60-B,
AC50A-B, AC60A-B, AC50B-B,
AC55B-B, AC60B-B
Applicable model
1/8
1/4
3/8
1/4
3/8
1/2
1/4
3/8
1/2
3/4
3/4
Note) 쏔 in model numbers indicates a pipe thread type. No indication is
necessary for Rc; however, indicate N for NPT, and F for G.
∗ Separate interfaces are required for modular unit.
∗ Factory mounting of a piping adapter on the AC models is available as a
special order.
Pressure Switch with Piping Adapter
IS10E 30
q
w
Symbol
A
03
e
r
• Semi-standard: Select one each for a to d.
• Semi-standard symbol: When more than one specification is required, indicate in alphanumeric order.
Example) IS10E-30N03-6PRZ
Symbol
Description
—
Rc
NPT
G
Left
Right
q
앬
Pressure switch with
piping adapter
Body size
20 30 40
Port size
+
a
Set pressure
range
—
6 Note 1)
— —
—
— —
0.1 to 0.4 MPa
0.1 to 0.6 MPa
E
(23)
e
앬
23
1/8
1/4
3/8
1/2
3/4
(5000)
(3000)
(500)
+
01
02
03
04
06
(13)
N Note)
F Note)
Pipe thread type
MPa
r
앬
Semi-standard
b
Lead wire
length
L
Z
B
+
—
0.1
0.3
0.2
0.4
Port
size
C
w
앬
0.5 m
3m
5m
+
c
—
Pressure unit of
the scale plate P Note 2)
D
MPa
MPa/psi dual scale
Centre of F.R.L. body
A
+
d
Mounting
position
—
R
Right
Left
Note 1) Set pressure range of 6P (L, R, Z) is 0.2 to 0.6 MPa (30 to 90 psi).
Note 2) For pipe thread type: NPT only.
Specifications
Fluid
Ambient and fluid temperature
Proof pressure
Maximum operating pressure
Set pressure range (when OFF)
Hysteresis
Air
−5 to 60°C (with no freezing)
1.0 MPa
0.7 MPa
0.1 to 0.4 MPa
0.08 MPa or less
Switch Characteristics
Contact point configuration
Maximum contact point capacity
Operating voltage: AC, DC
Maximum operating current
37
1a
2 VA (AC), 2 W (DC)
100 V or less
12 V to 24 V AC, DC: 50 mA
48 V AC, DC: 40 mA
100 V AC, DC: 20 mA
Model Note 1)
IS10E-20쏔01-A
IS10E-20쏔02-A
IS10E-20쏔03-A
IS10E-30쏔02-A
IS10E-30쏔03-A
IS10E-30쏔04-A
IS10E-40쏔02-A
IS10E-40쏔03-A
IS10E-40쏔04-A
IS10E-40쏔06-A
Port size
1/8
1/4
3/8
1/4
3/8
1/2
1/4
3/8
1/2
3/4
A
B
C
D
E
29.8
66.3
55.3
28
16
AC20쏔-B
31.8
72.8
58.8
30
13
AC25쏔-B,
AC30쏔-B
31.8
78.8
60.8
37
12.5 AC40쏔-B
Applicable model
Note 2)
Note 1) 쏔 in the model numbers indicates a pipe thread type. No indication is
necessary for Rc; however, indicate N for NPT, and F for G.
Note 2) Cannot be mounted on the AC40쏔-06-B.
∗ Separate interfaces are required for modular unit.
∗ The pressure switch on the AC40쏔-06-B can be mounted by screwing IS1001S into the piping adapter E500-쏔06-A-X501 (with top-face thread Rc1/8).
Products with a premounted switch are available as a special order. Please
contact SMC regarding their availability.
Series
AC
Accessories (Spacers/Brackets)
AC
Spacer
D
B
C
AF AR AL
Centre of
F.R.L. body
A
B
C
D
Applicable model
17.9
31.2
43.4
53
57
67.6
9
15.6
21.7
26.5
28.5
33.8
35.4
44.9
57.9
68.5
75.6
92.5
AC10씲-A
AC20씲-B
AC25씲-B, AC30씲-B
AC40씲-B
AC40씲-06-B
AC50씲-B, AC55씲-B, AC60씲-B
AF AR
A
6
3.2
4.2
5.2
5.2
6.2
Y200-A
Y400-A
Replacement Parts
Part no.
Description
Material
Seal
HNBR (NBR) Note 1)
Y100-A
Y200-A
Y300-A
Y400-A
Y500-A
Y600-A
Y120P-050AS Note 2)
Y220P-050S
Y320P-050S
Y420P-050S
Y520P-050S
Y620P-050S
AW AFM
Note 1) ( ): Size 10
Note 2) Assembly of 2 O-rings
Spacer with Bracket
D
AF
B
AFM / AFD
E
EE
Seal
(Y100T-A, Y200T-A only)
E
Centre of
F.R.L. body
C
G
J
Attachment
H
F
K
A
A
B
C
D
6
3.2
4.2
5.2
5.2
56
67
82
96
96
24.5
29
41
48
48
43.6
53.4
71.5
86.1
89.6
Y600T-A 6.2 120 60
118
E EE
F
G
H
J
K
6.8
12
14
18
18
4.5
5.5
7
9
9
13
15.5
19
26
26
3
3.5
4
5
5
25
30
41
50
50
31.2
6
20
24
35
40
40
27
33
—
—
—
50
— 20
11
Applicable model
AC10씲-A
AC20씲-B
AC25씲-B, AC30씲-B
AC40씲-B
AC40씲-06-B
AC50씲-B, AC55씲-B,
70
AC60씲-B
AL
Model
AR
(Spacer width)
Y100T-A
Y200T-A
Y300T-A
Y400T-A
Y500T-A
AF AFM AR
Model
Y100-A
Y200-A
Y300-A
Y400-A
Y500-A
Y600-A
AW AL
(Spacer width)
Seal
Y200T-A
Y400T-A
Description
Material
Seal
HNBR (NBR) Note 1)
AW
Replacement Parts
Part no.
Y100T-A
Y200T-A
Y300T-A
Y400T-A
Y500T-A
Y600T-A
Y120P-050AS Note 2)
Y220P-050S
Y320P-050S
Y420P-050S
Y520P-050S
Y620P-050S
Note 1) ( ): Size 10
Note 2) Assembly of 2 O-rings
38
Series AC
Mounting Position for Spacer with Bracket
Bracket
T-spacer: T
Pressure switch: S Check valve: K
IN
Pressure relief
3 port valve: V
OUT
IN
OUT
Bracket
A1
39
A2
A3
A4
A1
S
A1
—
AC10B-A
AC20B-B 41.6
AC25B-B 55.1
AC30B-B 55.1
AC40B-B 72.6
AC40B-06-B 77.6
AC50B-B 93.1
AC55B-B 98.1
AC60B-B 98.1
Model
Attachment
A4
—
43.2
57.2
57.2
75.2
—
—
—
—
A1
41.6
55.1
72.6
77.6
93.1
—
A2
43.2
57.2
75.2
80.2
96.2
—
A1
41.6
55.1
72.6
—
—
—
T
V
A1
28
41.6
55.1
55.1
72.6
77.6
93.1
98.1
98.1
A1
A2
—
—
41.6 43.2
55.1 57.2
55.1 57.2
72.6 75.2
77.6 80.2
93.1 189.3
—
—
—
—
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
—
—
A2
—
43.2
57.2
57.2
75.2
80.2
96.2
—
—
A2
43.2
57.2
57.2
75.2
80.2
A1
41.6
55.1
55.1
72.6
77.6
A2
43.2
57.2
57.2
75.2
80.2
A1
41.6
55.1
55.1
72.6
77.6
A2
43.2
57.2
57.2
75.2
80.2
A2
43.2
57.2
75.2
80.2
A1
41.6
55.1
72.6
77.6
S
V
V
A3
43.2
57.2
75.2
—
—
—
A1
41.6
55.1
72.6
—
—
—
A1
41.6
55.1
72.6
—
—
—
A2
43.2
57.2
75.2
80.2
A2
43.2
57.2
75.2
—
—
—
SV
A2
—
57
74
74
95
102
124
—
—
A3
43.2
57.2
57.2
75.2
80.2
A1
41.6
55.1
55.1
72.6
77.6
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
—
—
A2
—
61
76
76
99
104
124
124
129
A2
57
74
95
—
—
—
A3
43.2
57.2
75.2
—
—
—
A1
41.6
55.1
72.6
77.6
93.1
—
A2
—
61
76
76
99
104
124
—
—
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
—
—
A2
—
43.2
57.2
57.2
75.2
80.2
96.2
—
—
A3
57
74
74
95
102
A1
41.6
55.1
55.1
72.6
77.6
TV
A2
—
43.2
57.2
57.2
75.2
80.2
96.2
—
—
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
—
—
A3
43.2
57.2
57.2
75.2
80.2
A1
41.6
55.1
55.1
72.6
77.6
V1
SV
A1
41.6
55.1
72.6
77.6
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
98.1
98.1
KSV
SV1
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
—
—
V
V1
A4
—
43.2
57.2
57.2
75.2
—
—
—
—
A2
57
74
95
102
A2
43.2
57.2
57.2
75.2
80.2
SV1
A1
41.6
55.1
72.6
77.6
A2
43.2
57.2
75.2
80.2
A2
—
61
76
76
99
—
—
—
—
A3
—
43.2
57.2
57.2
75.2
—
—
—
—
A2
—
43.2
57.2
57.2
75.2
—
—
—
—
A1
A2
A3
—
—
—
41.6 43.2
57
55.1 57.2
74
55.1 57.2
74
72.6 75.2
95
77.6 80.2 102
93.1 189.3 124
—
—
—
—
—
—
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
—
—
SV
A3
—
43.2
57.2
57.2
75.2
—
—
—
—
KST
A4
—
43.2
57.2
57.2
75.2
—
—
—
—
A1
—
41.6
55.1
55.1
72.6
—
—
—
—
A2
—
61
76
76
99
104
124
—
—
A3
—
57
74
74
95
102
124
—
—
A1
—
41.6
55.1
55.1
72.6
77.6
93.1
—
—
A3
61
76
76
99
104
A1
41.6
55.1
55.1
72.6
77.6
STV
A2
—
61
76
76
99
—
—
—
—
A3
—
57
74
74
95
—
—
—
—
TV
A2
—
61
76
76
99
104
124
—
—
A3
—
43.2
57.2
57.2
75.2
80.2
96.2
—
—
SV
A2
57
74
95
102
124
—
TV1
SV
A2
43.2
57.2
57.2
75.2
80.2
KV
A1
—
41.6
55.1
55.1
72.6
—
—
—
—
ST
KV
A2
57
74
95
—
—
—
A1
—
41.6
55.1
55.1
72.6
—
—
—
—
AC
A3
—
57
74
74
95
—
—
—
—
A3
—
57
74
74
95
—
—
—
—
AF AR AL
A2
—
61
76
76
99
—
—
—
—
KS
T
A1
41.6
55.1
72.6
77.6
A1
—
41.6
55.1
55.1
72.6
—
—
—
—
KT
A2
—
43.2
57.2
57.2
75.2
—
—
—
—
KSTV
A3
—
43.2
57.2
57.2
75.2
—
—
—
—
V1
A1
—
41.6
55.1
55.1
72.6
—
—
—
—
AW AL
A2
—
61
76
76
99
—
—
—
—
S
A1
AC20D-B 41.6
AC30D-B 55.1
AC40D-B 72.6
AC40D-06-B 77.6
A4
—
43.2
57.2
57.2
75.2
—
—
—
—
KTV
A1
—
41.6
55.1
55.1
72.6
—
—
—
—
S
A1
AC20C-B 41.6
AC25C-B 55.1
AC30C-B 55.1
AC40C-B 72.6
AC40C-06-B 77.6
Model
A3
—
43.2
57.2
57.2
75.2
80.2
—
—
—
AF AR
A1
41.6
55.1
72.6
77.6
93.1
98.1
A2
—
43.2
57.2
57.2
75.2
80.2
—
—
—
AW AFM
A2
43.2
57.2
75.2
—
—
—
KS
A1
—
41.6
55.1
55.1
72.6
77.6
—
—
—
Attachment
A3
—
57
74
74
95
—
—
—
—
K
A1
AC20A-B 41.6
AC30A-B 55.1
AC40A-B 72.6
AC40A-06-B —
—
AC50A-B
—
AC60A-B
Attachment
A2
—
43.2
57.2
57.2
75.2
—
—
—
—
V
A2
48.2
61
76
76
99
104
124
124
129
SV1
A2
43.2
57.2
57.2
75.2
80.2
TV
A3
43.2
57.2
57.2
75.2
80.2
A1
41.6
55.1
55.1
72.6
77.6
A2
43.2
57.2
57.2
75.2
80.2
AF
Attachment
Model
Model
A1
28
41.6
55.1
55.1
72.6
77.6
93.1
98.1
98.1
KSV
A1
—
AC10-A
41.6
AC20-B
55.1
AC25-B
55.1
AC30-B
72.6
AC40-B
AC40-06-B —
—
AC50-B
—
AC55-B
—
AC60-B
Model
Attachment
T
A1
A2
—
—
41.6 43.2
55.1 57.2
55.1 57.2
72.6 75.2
77.6 80.2
93.1 96.2
98.1 96.2
98.1 101.2
TV1
A2
43.2
57.2
57.2
75.2
80.2
A3
43.2
57.2
57.2
75.2
80.2
AFM / AFD
Attachment
S
A3
—
43.2
57.2
57.2
75.2
—
—
—
—
A1: Dimension from the end of the IN side to the centre of the mounting hole for the
first bracket.
A2: Mounting hole pitch between the first and the second brackets.
A3: Mounting hole pitch between the second and the third brackets.
A4: Mounting hole pitch between the third and the fourth brackets.
AR
A2
—
43.2
57.2
57.2
75.2
—
—
—
—
AL
K
A1
—
AC10-A
41.6
AC20-B
55.1
AC25-B
55.1
AC30-B
72.6
AC40-B
AC40-06-B —
—
AC50-B
—
AC55-B
—
AC60-B
AW
Attachment
Model
Series AC
AF AFM AR
Attachments
40
41
M5 x 0.8
AF20-A
1/8, 1/4
AF30-A
1/4, 3/8
AF40-A
1/4, 3/8, 1/2
Mist Separator
Series AFM
Filtration
μm
Options
AW AL
AF10-A
Bracket (Except AF10-A)
5
AF AR
AF40-06-A
P.43 to 51
Port size
Float type auto drain
3/4
AF50-A
3/4, 1
AF60-A
1
AFM20-A
1/8, 1/4
AFM30-A
1/4, 3/8
AF AFM AR
Model
AW AFM
Air Filter
Series AF
AF AR AL
Series AF/AFM/AFD
Bracket
0.3
P.53 to 60
Micro Mist Separator
Series AFD
AFM40-06-A
Float type auto drain
1/4, 3/8, 1/2
Attachment
AFM40-A
3/4
AFD20-A
1/8, 1/4
AFD30-A
1/4, 3/8
Bracket
AFM / AFD
AR
3/4
AL
AFD40-06-A
Float type auto drain
AW
P.53 to 60
1/4, 3/8, 1/2
AF
0.01
AFD40-A
AC
Modular Type
Air Filters
42
Air Filter
AF10-A to AF60-A
Symbol
Air Filter
Air Filter with Auto Drain
1
2
1
2
L
L
AF10-A
AF20-A
AF40-A
How to Order
AF 30
q
A
03 BD
w
e
r
t Made to Order
• Option/Semi-standard: Select one each for a to f.
• Option/Semi-standard symbol: When more than one specification is
required, indicate in alphanumeric order.
Example) AF30-03BD-R-A
(Refer to pages 50 and 51 for details.)
Symbol
Pipe thread type
20
30
40
50
60
N Note 1)
F Note 2)
Metric thread (M5)
Rc
NPT
G
앬
—
—
—
—
앬
앬
앬
—
앬
앬
앬
—
앬
앬
앬
—
앬
앬
앬
—
앬
앬
앬
M5
01
02
03
04
06
10
M5 x 0.8
1/8
1/4
3/8
1/2
3/4
1
앬
—
—
—
—
—
—
—
앬
앬
—
—
—
—
—
—
앬
앬
—
—
—
—
—
앬
앬
앬
앬
—
—
—
—
—
—
앬
앬
—
—
—
—
—
—
앬
앬
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
—
앬
앬
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
+
e
Port size
+
r
Option
a
Mounting
—
Without mounting option
B Note 3) With bracket
+
b
Float type
auto drain
—
Without auto drain
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
+
t
Semi-standard
c
—
2
6
8
C
6C
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
With bowl guard (Nylon bowl)
앬
앬
앬
—
—
—
앬
앬
앬
—
앬
앬
—
W Note 11)
With drain cock
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting
앬
—
—
—
앬
앬
—
—
앬
—
앬
앬
앬
—
앬
앬
앬
—
앬
앬
앬
—
앬
앬
—
R
Flow direction: Left to right
Flow direction: Right to left
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
—
Name plate and caution plate for bowl in imperial units: MPa
Bowl Note 6)
+
d Drain port
Note 9)
J
Note 10)
+
e
Flow direction
+
f
Pressure unit
Body size
10
—
w
q
Description
Z Note 12) Name plate and caution plate for bowl in imperial units: psi, °F
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
— Note 7) — Note 7) — Note 7) — Note 7)
— Note 8) — Note 8) — Note 8) — Note 8)
앬
앬
앬
앬
앬
앬
앪 Note 13) 앪 Note 13) 앪 Note 13) 앪 Note 13) 앪 Note 13) 앪 Note 13)
Note 1) Drain guide is NPT1/8 (applicable to the AF20-A) and NPT1/4 (applicable to the AF30-A to AF60-A).
The auto drain port comes with ø3/8" One-touch fitting (applicable to the AF30-A to AF60-A).
Note 2) Drain guide is G1/8 (applicable to the AF20-A) and G1/4 (applicable to the AF30-A to AF60-A).
The auto drain port comes with ø10 One-touch fitting (applicable to the AF30-A to AF60-A).
Note 3) Option B is not assembled and supplied loose at the time of shipment. Assembly of a bracket and 2 mounting screws.
Note 4) When pressure is not applied, condensate which does not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending operations for the day is recommended.
Note 5) If the compressor is small (0.75 kW, discharge flow is less than 100 L/min [ANR]), air leakage from the drain cock may occur during start of operations. N.C. type is recommended.
Note 6) Refer to Chemical data on page 46 for chemical resistance of the bowl.
Note 7) A bowl guard is provided as standard equipment (polycarbonate).
Note 8) A bowl guard is provided as standard equipment (nylon).
Note 9) The combination of float type auto drain: C and D is not available.
Note 10) Without a valve function
Note 11) The combination of metal bowl: 2 and 8 is not available.
Note 12) For pipe thread type: M5, NPT.
Note 13) 앪: For pipe thread type: M5, NPT only
43
Air Filter
Series AF10-A
to AF60-A
AF20-A
AF30-A
M5 x 0.8
1/8, 1/4
1/4, 3/8
AF40-A
AF40-06-A
2.5
8
25
—
0.06
Semi-standard (Steel)
0.08
0.18
AF10-A
AF20-A
AF30-A
AF40-A
AF40-06-A
—
AF22P-050AS
AF32P-050AS
AF42P-050AS
AF42P-070AS
1/4, 3/8, 1/2
3/4
Air
–5 to 60 °C (with no freezing)
1.5 MPa
1.0 MPa
5 μm
AF50-A
AF60-A
3/4, 1
1
45
Polycarbonate
Standard (Polycarbonate)
0.36
0.41
0.87
AF AR AL
AF10-A
AW AL
Model
Port size
Fluid
Ambient and fluid temperature
Proof pressure
Maximum operating pressure
Nominal filtration rating
Drain capacity [cm3]
Bowl material
Bowl guard
Weight [kg]
AC
Standard Specifications
1.00
AF AR
Options/Part No.
Model
Optional specifications
Bracket assembly Note)
AF50-A
AF60-A
AF52P-050AS
Bowl Assembly/Part No.
Model
Automatic Normally closed (N.C.)
discharge Note)
(Auto drain) Normally open (N.O.)
With drain cock
Nylon bowl
Manual
Drain cock with barb fitting
discharge
With drain guide
(without valve function)
Automatic Normally closed (N.C.)
discharge Note)
(Auto drain) Normally open (N.O.)
Metal bowl
With drain cock
Manual
discharge With drain guide
(without valve function)
Automatic Normally closed (N.C.)
discharge Note)
(Auto drain) Normally open (N.O.)
C1SF-A
—
—
—
—
AD17-A
—
—
C1SF-6-A
—
—
—
—
AD17-6-A
—
—
C1SF-2-A
—
—
—
AD17-2-A
—
—
—
AF20-A
AF30-A
C2SF-A
—
C2SF-C-A
C3SF-A
—
C3SF-W-A
C2SF첸-J-A
—
C2SF첸-CJ-A C3SF첸-J-A
AD27-A
—
AD27-C-A
AD37첸-A
—
AD38첸-A
C2SF-6-A
—
C2SF-6C-A
C3SF-6-A
—
C3SF-6W-A
C2SF첸-6J-A
—
C2SF첸-6CJ-A C3SF첸-6J-A
AD27-6-A
—
AD27-6C-A AD37첸-6-A
—
AD38첸-6-A
C2SF-2-A
C3SF-2-A
—
C3LF-8-A
C2SF첸-2J-A C3SF첸-2J-A
—
C3LF첸-8J-A
AD27-2-A
AD37첸-2-A
—
AD37첸-8-A
AD38첸-2-A
—
—
AD38첸-8-A
AF40-A AF40-06-A AF50-A AF60-A
—
C4SF-A
C4SF-W-A
—
C4SF첸-J-A
—
AD47첸-A
AD48첸-A
—
C4SF-6-A
C4SF-6W-A
—
C4SF첸-6J-A
—
AD47첸-6-A
AD48첸-6-A
C4SF-2-A
C4LF-8-A
C4SF첸-2J-A
C4LF첸-8J-A
AD47첸-2-A
AD47첸-8-A
AD48첸-2-A
AD48첸-8-A
AW AFM
Manual
Drain cock with barb fitting
discharge
Polycarbonate
With drain guide
bowl
(without valve function)
—
With bowl guard
With bowl guard
—
With bowl guard
—
With bowl guard
With bowl guard
—
With bowl guard
With bowl guard
—
With bowl guard
—
With bowl guard
With bowl guard
—
With level gauge
—
With level gauge
—
With level gauge
—
With level gauge
AF10-A
Attachment
With drain cock
Other
AF
Drain port
AFM / AFD
Drain
discharge
mechanism
AR
Bowl
material
AF AFM AR
Note) Assembly of a bracket and 2 mounting screws
AW
AL
Note) Minimum operating pressure: N.O. type–0.1 MPa (AD38-A, AD48-A); N.C. type–0.1 MPa (AD17-A, AD27-A) and 0.15 MPa (AD37-A, AD47-A).
Bowl assembly for the AF20-A to AF60-A models comes with a bowl seal.
씲 in bowl assembly part numbers indicates a pipe thread type (applicable tubing for auto drain).
No indication is necessary for Rc thread; however, indicate N for NPT thread, and F for G thread. (For auto drain, —: ø10, N: ø3/8")
Please consult with SMC separately for psi and °F unit display specifications.
44
Series AF10-A
to AF60-A
Flow-rate Characteristics (Representative values)
M5
AF20-A
AF30-A
0.10
0.02
0
150
0
0
200
500
1000
1500
AF40-06-A
Rc3/4
4000
AF60-A
P1
0.02
Rc1
a
MP
P1
=0
MP
.5
.7
a
a
MP
=0
0.3
P1=
MP
a
0.06
P1
0.08
P1=
0.1
0.04
0.02
0
0
5000
10000
Flow rate L/min (ANR)
15000
Pressure drop [MPa]
0.04
=0
MP
.3
P1
=0
a
MP
0.1
P1=
Pressure drop [MPa]
0.06
a
P1=
Rc1
0.08
0.06
0.04
0.02
0
2000
4000
Flow rate L/min (ANR)
0.10
Pressure drop [MPa]
0.08
0
6000
Flow rate L/min (ANR)
45
a
P1
=0
.5
M
.7
Pa
M
Pa
a
MP
P1
=0
.7
MP
a
Pa
.5
0.3
M
P1=
P1
=0
Pa
.1 M
Pressure drop [MPa]
P1=0
2000
4000
0.10
0
0
0
.1 MP
AF50-A
0.10
0.02
3000
MP
a
P1
=0
.5
MP
P1
a
=0
.7
MP
a
0.10
2000
Flow rate L/min (ANR)
0.3
Rc1/2
0.04
1000
P1=
AF40-A
0.06
0
Flow rate L/min (ANR)
Flow rate L/min (ANR)
0.08
0.02
a
100
0.04
MP
50
P1=0
MP
MP
a
0.5
.7
P1
=0
0.3
MP
a
P1=
P1=
Pa
0.1
M
0.04
0.06
0.1
0
0
0.06
0.08
P1=
0.02
0.08
Pressure drop [MPa]
P1=
0.04
0.10
P1=
Pressure drop [MPa]
7
MP
.5
=0
.
P1
=0
P1
0.1
M
Pa
0.06
M
Pa
a
a
MP
P1=
0.3
0.08
Rc3/8
a
0.10
Pressure drop [MPa]
Rc1/4
0.3
MP
a
P1=
0.5
MP
P1
a
=0
.7
MP
a
AF10-A
6000
0
5000
10000
Flow rate L/min (ANR)
15000
Series AF10-A
to AF60-A
Maintenance
Warning
Warning
1. The standard bowl for the air filter, filter regulator, and
lubricator, as well as the sight dome for the lubricator
are made of polycarbonate. Do not use in an environment where they are exposed to or come in contact
with organic solvents, chemicals, cutting oil, synthetic
oil, alkali, and thread lock solutions.
Effects of atmosphere of organic solvents and chemicals, and
where these elements are likely to adhere to the equipment.
Chemical data for substances causing degradation (Reference)
Aromatic
series
Ketone
Alcohol
Oil
Ester
Ether
Amino
Gasoline
Kerosene
Phthalic acid dimethyl
Phthalic acid diethyl
Acetic acid
Methyl ether
Ethyl ether
Methyl amino
Degreasing of metals
Industrial salts
Water-soluble
cutting oil
҂
쑗
—
҂
왕
Cleansing liquid for metals
Printing ink
Dilution
҂
왕
Coatings
Dry cleaning
҂
왕
Photographic film
Dry cleaning
Textile industries
҂
҂
Antifreeze
Adhesives
왕
҂
҂
쑗
Synthetic oil
Anti-rust additives
҂
쑗
Brake oil additives
҂
쑗
Cutting oil
Brake oil additives
Rubber accelerator
҂
҂
҂
왕
—
Thread-lock fluid
Seawater
—
Leak tester
쑗: Essentially safe 왕: Some effects may occur.
Others
҂
Attachment
AW AFM
Lock button
AF
Chlorine
solvents
왕
AFM / AFD
Inorganic
salts
Acid washing
liquid for metals
AR
Alkaline
Hydrochloric acid
Sulfuric acid, Phosphoric acid
Chromic acid
Sodium hydroxide (Caustic soda)
Potash
Calcium hydroxide (Slack lime)
Ammonia water
Carbonate of soda
Sodium sulfide
Sulfate of potash
Sulfate of soda
Carbon tetrachloride
Chloroform
Ethylene chloride
Methylene chloride
Benzene
Toluene
Paint thinner
Acetone
Methyl ethyl ketone
Cyclohexane
Ethyl alcohol
IPA
Methyl alcohol
Material
Application examples PolycarNylon
bonate
Caution
1. When the bowl is installed on the air filter (AF30-A to AF60-A),
install them so that the lock button lines up to the groove of the
front (or the back) of the body to avoid drop or damage of the
bowl.
AL
Acid
Chemical name
Mounting/Adjustment
AW
Type
1. Replace the element every 2 years or when the pressure drop
becomes 0.1 MPa, whichever comes first, to prevent damage
to the element.
AW AL
Design/Selection
AF AR
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
AF AR AL
AC
Specific Product Precautions
AF AFM AR
Air Filter
҂: Effects will occur.
When the above factors are present, or there is some doubt, use a metal bowl
for safety.
46
Series
AF10-A to AF60-A
Working Principle: Float Type Auto Drain
N.O. type: AD38-A, AD48-A
Compact auto drain N.C. type:
N.C. type: AD37-A, AD47-A
AD17-A, AD27-A
: Bowl
; Valve
. Lever
@ Float
= Valve seat
2 Chamber
> Piston
B Spring
8 Housing
Seal
Drain cock
: Bowl
; Valve
. Lever
@ Float
= Valve seat
2 Chamber
B Spring
> Piston
8 Housing
Seal
Drain cock
: Bowl
@Float
.Lever
; Valve
= Valve seat
B Knob
Drain
Drain
Drain
• When pressure inside the bowl is
released:
• When pressure inside the bowl is
released:
• When pressure inside the bowl is
released:
When pressure is released from the bowl q,
the piston u is lowered by the spring y.
The sealing action of the seal !0 is interrupted,
and the outside air flows inside the bowl q
through the housing hole o and the drain cock
!1.
Therefore, if there is an accumulation of condensate in the bowl q, it will drain out through
the drain cock.
Even when pressure inside the bowl q is released, spring y keeps the piston u in its upward position.
This keeps the seal created by the seal !0 in
place; thus, the inside of the bowl q is shut off
from the outside air.
Therefore, even if there is an accumulation of
condensate in the bowl q, it will not drain out.
Even when pressure inside the bowl q is released, the weight of the float w causes the
valve r, which is connected to the lever e, to
seal the valve seat t. As a result, the inside of
the bowl q is shut off from the outside air.
Therefore, even if there is an accumulation of
condensate in the bowl q, it will not drain out.
• When pressure is applied inside the
bowl:
• When pressure is applied inside the
bowl:
When pressure is 0.1 MPa or more, the force of
the piston u surpasses the force of the spring
y, and the piston goes up.
This pushes seal !0 up so that it creates a seal,
and the inside of the bowl q, is shut off from
the outside air.
If there is no accumulation of condensate in the
bowl q at this time, the float w will be pulled
down by its own weight, causing the valve r,
which is connected to the lever e, to seal the
valve seat t.
Even when pressure is applied inside the bowl
q, the combined force of the spring y and the
pressure inside the bowl q keeps the piston u
in its upward position.
This maintains the seal created by the seal !0
in place; thus, the inside of the bowl q is shut
off from the outside air.
If there is no accumulation of condensate in the
bowl q at this time, the float w will be pulled
down by its own weight, causing the valve r,
which is connected to the lever e, to seal the
valve seat t.
• When there is an accumulation of
condensate in the bowl:
• When there is an accumulation of
condensate in the bowl:
The float w rises due to its own buoyancy and
the seal at the valve seat t is interrupted.
This allows the pressure inside the bowl q to
enter the chamber i. The result is that the
combined pressure inside the chamber i and
the force of the spring y lowers the piston u.
This causes the sealing action of the seal !0 to
be interrupted, and the accumulated condensate in the bowl q drains out through the drain
cock !1.
Turning the drain cock !1 manually counterclockwise lowers the piston u, and causes the
seal created by the seal !0 to be interrupted,
thus allowing the condensate to drain out.
The float w rises due to its own buoyancy and
the seal at the valve seat t is interrupted.This
allows the pressure inside the bowl q to enter
the chamber i.
The result is that the pressure inside the chamber i surpasses the force of the spring y and
pushes the piston u downward.
This causes the sealing action of the seal !0 to be
interrupted and the accumulated condensate in
the bowl q drains out through the drain cock !1.
Turning the drain cock !1 manually counterclockwise lowers the piston u, and causes the
seal created by the seal !00 to be interrupted,
thus allowing the condensate to drain out.
47
• When pressure is applied inside the
bowl:
Even when pressure is applied inside the bowl
q, the weight of the float w and the differential
pressure that is applied to the valve r cause
the valve r to seal the valve seat t, and the
outside air is shut off from the inside of the bowl
q.
• When there is an accumulation of
condensate in the bowl:
The float w rises due to its own buoyancy and
the seal at the valve seat t is interrupted.
The condensate inside the bowl q drains out
through the knob y.
Turning the knob y manually counterclockwise
lowers it and causes the sealing action of the
valve seat t to be interrupted, which allows
the condensate to drain out.
Air Filter
Series AF10-A
to AF60-A
Construction
:
;
@
:
;
@
.
=
=
.
AC
OUT
IN
:
@
B
.
;
Drain
=
AF
Attachment
AW AFM
Drain
AW AL
OUT
IN
AF AR
OUT
IN
AF50-A /AF60-A
AF AR AL
AF30-A to AF40-06-A
AF AFM AR
AF10-A /AF20-A
Drain
Description
1
Body
6
Housing
Material
Model
Zinc die-cast
AF10-A
Colour
Aluminium die-cast
AF20-A to AF60-A
Aluminium die-cast
AF50-A /AF60-A
White
White
No.
Description
Material
AR
Replacement Parts
Part no.
AF10-A
AF20-A
AF30-A
AF40-A
Non-woven fabric
AF10P-060S
AF20P-060S
AF30P-060S
AF40P-060S
AF40-06-A
AF42P-040S
AF50-A
AF60-A
AF50P-060S
AF60P-060S
AF50P-040S
AF60P-040S
2
Filter element
3
Baffle
PBT
AF10P-040S Note 2)
AF22P-040S
AF32P-040S
4
Bowl seal
NBR
C1SFP-260S
C2SFP-260S
C32FP-260S
C42FP-260S
5
Bowl assembly Note 1)
Polycarbonate
C1SF-A
C2SF-A
C3SF-A
C4SF-A
AL
No.
AFM / AFD
Component Parts
AW
Note 1) Bowl seal is included for the AF20-A to AF60-A. Please contact SMC regarding the supply of bowl assembly with psi and °F unit specifications.
Note 2) The baffle material for the AF10-A (AF10P-040S) only is polyacetal.
48
Series AF10-A
to AF60-A
Dimensions
AF10-A /AF20-A
M
U
D
AF50-A /AF60-A
T
N
S
Bracket
(Option)
C
R
Bracket
(Option)
Q
V
J
OUT
IN
J
T
N
M
U
2xP
(Port size)
S
Drain
A
C
IN
OUT
G
Clearance for
maintenance
Q
V
R
B
D
AF30-A to AF40-06-A
T
N
S
IN
OUT
B
2xP
(Port size)
C
Bracket
(Option)
R
M
U
D
Q
V
J
Drain
A
AF10-A /AF20-A
B
With drain guide
Dimensions
Width across
flats 14
M5 x 0.8
Metal bowl with drain guide
With auto drain (N.O./N.C.)
N.O.: Black
N.C.: Grey
Width across
flats 14
1/8
1/8
Thread type/Rc, G: ø10 One-touch fitting
Thread type/NPT: ø3/8" One-touch fitting
AF30-A to AF60-A
Metal bowl with level gauge,
with drain guide
With drain guide
Drain cock with barb fitting
B
Dimensions
Width across
flats 17
Width across
flats 17
1/4
1/4
Width across
flats 17
Optional specifications
Standard specifications
Model
P
M5 x 0.8
AF10-A
1/8, 1/4
AF20-A
1/4, 3/8
AF30-A
1/4, 3/8, 1/2
AF40-A
3/4
AF40-06-A
3/4, 1
AF50-A
1
AF60-A
49
A
B
C
25
40
53
70
75
90
95
59.9
87.6
115.1
147.1
149.1
220.1
234.1
7
9.8
14
18
20
24
24
D
E
G
J
25
25
35
40
40
30
30
12.5
20
26.7
35.5
35.5
45
47.5
M N Q
—
30
41
50
50
70
70
—
27
40
54
54
66
66
R
— —
22 5.4
23 6.5
26 8.5
25 8.5
35 11
35 11
Barb fitting
applicable
tubing: T0604
1/4
Semi-standard specifications
With
auto
drain
Bracket mount
12.5 —
20
—
26.7 30
35.5 38.4
35.5 38.4
45
—
47.5 —
B
B
B
Metal bowl with drain guide
B
Metal bowl
Metal bowl
with level gauge
B
Applicable model
Optional/Semi-standard
specifications
AF30-A to AF60-A
B
Metal bowl
B
With auto drain (N.C.)
AF20-A
B
Applicable model
Optional/Semi-standard
specifications
B
Clearance for
maintenance
Drain
G
A
E
G
Clearance for
maintenance
B
2xP
(Port size)
With
barb
fitting
With
drain
guide
Metal
bowl
Metal bowl Metal bowl
with drain with level
guide
gauge
Metal bowl
with level
gauge, with
drain guide
S
T
U
V
B
B
B
B
B
B
B
—
8.4
8
10.5
10.5
13
13
—
40
53
70
70
90
90
—
2.3
2.3
2.3
2.3
3.2
3.2
—
28
30
35
34
47
47
77.9
104.9
156.8
186.9
188.9
259.9
273.9
—
—
123.6
155.6
157.6
228.6
242.6
—
91.4
121.9
153.9
155.9
226.9
240.9
59.3
87.4
117.6
149.6
151.6
222.6
236.6
—
93.9
122.1
154.1
156.1
227.1
241.1
—
—
137.6
169.6
171.6
242.6
256.6
—
—
142.1
174.1
176.1
247.1
261.1
Air Filter/AF20-A to AF40-06-A
Made to Order
AC
Please contact SMC for detailed dimensions, specifications and lead times.
q Long Bowl
AF AR AL
Drain capacity is greater than that of standard models.
Applicable Model/Drain Capacity
Model
AF20-A
AF30-A
AF40-A
Port size
1/8, 1/4
1/4, 3/8
1/4, 3/8, 1/2
Drain capacity [cm3]
19
43
AF40-06-A
3/4
88
q
A X64
03
w
e
r
t
AF AR
AF 30
AW AL
Note) Please consult with SMC for dimensions.
Long bowl
AF AFM AR
• Semi-standard: Select one each for a to d.
• Option/Semi-standard symbol: When more than one specification is required, indicate in alphanumeric order.
Example) AF30-03B-2R-A-X64
q
Description
20
30
40
Pipe thread type
—
N Note 1)
F Note 2)
Rc
NPT
G
앬
앬
앬
앬
앬
앬
앬
앬
앬
Port size
01
02
03
04
06
1/8
1/4
3/8
1/2
3/4
앬
앬
—
—
—
—
앬
앬
—
—
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
Polycarbonate bowl
Metal bowl
Nylon bowl
With bowl guard
With bowl guard (Nylon bowl)
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
— Note 5)
— Note 6)
— Note 5)
— Note 6)
With drain cock
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting (for ø6 x ø4 nylon tube)
앬
앬
—
—
앬
—
앬
앬
앬
—
앬
앬
Flow direction: Left to right
Flow direction: Right to left
앬
앬
앬
앬
앬
앬
앬
앪 Note 10)
앬
앪 Note 10)
앬
앪 Note 10)
Option (Mounting)
Without mounting option
B Note 3) With bracket
+
t
Semi-standard
a
Bowl Note 4)
—
2
6
C
6C
+
—
b
Drain port
J Note 7)
W Note 8)
+
c
Flow direction
—
R
+
d
Pressure unit
—
Name plate and caution plate for bowl in imperial units: MPa
Z Note 9) Name plate and caution plate for bowl in imperial units: psi, °F
AW AFM
Attachment
r
AF
+
—
AFM / AFD
e
AR
+
Body size
AL
w
Symbol
AW
Note 1) Drain guide is NPT1/8 (applicable to the AF20-A) and NPT1/4 (applicable to the AF30-A to AF40-06-A).
The auto drain port comes with ø3/8" One-touch fitting (applicable to the AF30-A to AF40-06-A).
Note 2) Drain guide is G1/8 (applicable to the AF20-A) and G1/4 (applicable to the AF30-A to AF40-06-A).
Note 3) Option B is not assembled and supplied loose at the time of shipment. Assembly of a bracket and 2 mounting screws.
Note 4) Refer to Chemical data on page 46 for chemical resistance of the bowl.
Note 5) A bowl guard is provided as standard equipment (polycarbonate).
Note 6) A bowl guard is provided as standard equipment (nylon).
Note 7) Without a valve function
Note 8) The combination of metal bowl: 2 and 8 is not available.
Note 9) For pipe thread type: NPT.
Note 10) 앪: For pipe thread type: NPT only
50
Air Filter/AF20-A to AF40-06-A
Made to Order
Please contact SMC for detailed dimensions, specifications and lead times.
w With Element Service Indicator
Clogging status of elements can be checked visually.
Applicable Model
Model
AF20-A
AF30-A
AF40-A
AF40-06-A
Port size
1/8, 1/4
1/4, 3/8
1/4, 3/8, 1/2
3/4
AF 30
q
A X2141
03
w
e
r
t
• Option/Semi-standard: Select one each for a to f.
• Option/Semi-standard symbol: When more than one specification is
required, indicate in alphanumeric order.
Example) AF30-03BD-2R-A-X2141
With element service indicator
A special body type is required to mount the element service indicator. It cannot be mounted on a standard body.
q
Symbol
w
Pipe thread type
—
N Note 1)
F Note 2)
Port size
01
02
03
04
06
Description
20
30
40
Rc
NPT
G
앬
앬
앬
앬
앬
앬
앬
앬
앬
1/8
1/4
3/8
1/2
3/4
앬
앬
—
—
—
—
앬
앬
—
—
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
—
앬
앬
앬
앬
앬
앬
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
With bowl guard (Nylon bowl)
앬
앬
앬
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
— Note 7)
— Note 8)
— Note 7)
— Note 8)
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting (for ø6 x ø4 nylon tube)
앬
—
—
—
앬
앬
—
앬
앬
Flow direction: Left to right
Flow direction: Right to left
앬
앬
앬
앬
앬
앬
앬
앪 Note 13)
앬
앪 Note 13)
앬
앪 Note 13)
+
e
Body size
+
r
Option
a
Mounting
—
Without mounting option
B Note 3) With bracket
+
b
Float type
auto drain
—
Without auto drain
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
+
t
Semi-standard
c
Bowl Note 6)
—
2
6
8
C
6C
+
d Drain port Note 9)
J Note 10)
W Note 11)
+
e
Flow direction
—
R
+
f
Pressure unit
—
Name plate and caution plate for bowl in imperial units: MPa
Z Note 12) Name plate and caution plate for bowl in imperial units: psi, °F
Note 1) Drain guide is NPT1/8 (applicable to the AF20-A) and NPT1/4 (applicable to the AF30-A to AF40-06-A).
The auto drain port comes with ø3/8" One-touch fitting (applicable to the AF30-A to AF40-06-A).
Note 2) Drain guide is G1/8 (applicable to the AF20-A) and G1/4 (applicable to the AF30-A to AF40-06-A).
Note 3) Option B is not assembled and supplied loose at the time of shipment. Assembly of a bracket and 2 mounting screws.
Note 4) When pressure is not applied, condensate which does not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending operations for the day is recommended.
Note 5) If the compressor is small (0.75 kW, discharge flow is less than 100 L/min [ANR]), air leakage from the drain cock may occur during start of operations. N.C. type is recommended.
Note 6) Refer to Chemical data on page 46 for chemical resistance of the bowl.
Note 7) A bowl guard is provided as standard equipment (polycarbonate).
Note 8) A bowl guard is provided as standard equipment (nylon).
Note 9) The combination of float type auto drain: C and D is not available.
Note 10) Without a valve function
Note 11) The combination of metal bowl: 2 and 8 is not available.
Note 12) For pipe thread type: NPT.
Note 13) 앪: For pipe thread type: NPT only
51
52
AW
AL
AR
AFM / AFD
AF
Attachment
AW AFM
AF AFM AR
AF AR
AW AL
AF AR AL
AC
Mist Separator
Symbol
AFM20-A to AFM40-A
Mist Separator
1
Micro Mist Separator
L
AFD20-A to AFD40-A
AFM 30
03 BD
A
AFD 30
03 BD
A
w
e
r
t
AFM20-A
AFM40-A
AFD20-A
AFD40-A
Micro Mist Separator
1
• Series AFM Nominal filtration rating: 0.3 μm
• Series AFD Nominal filtration rating: 0.01 μm
How to Order
q
2
2
L
• Option/Semi-standard: Select one each for a to f.
• Option/Semi-standard symbol: When more than one
specification is required, indicate in alphanumeric order.
Example) AFM30-03BD-R-A
Made to Order
(Refer to pages 59 and 60 for details.)
q
w
Symbol
Description
20
30
40
Pipe thread type
—
N Note 1)
F Note 2)
Rc
NPT
G
앬
앬
앬
앬
앬
앬
앬
앬
앬
Port size
01
02
03
04
06
1/8
1/4
3/8
1/2
3/4
앬
앬
—
—
—
—
앬
앬
—
—
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
—
앬
앬
앬
앬
앬
앬
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
With bowl guard (Nylon bowl)
앬
앬
앬
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
— Note 7)
— Note 8)
— Note 7)
— Note 8)
With drain cock
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting (for ø6 x ø4 nylon tube)
앬
앬
—
—
앬
—
앬
앬
앬
—
앬
앬
Flow direction: Left to right
Flow direction: Right to left
앬
앬
앬
앬
앬
앬
앬
앪 Note 11)
앬
앪 Note 11)
앬
앪 Note 11)
+
e
Body size
+
r
Option
a
Mounting
—
Without mounting option
B Note 3) With bracket
+
b
Float type
auto drain
—
Without auto drain
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
+
t
Semi-standard
c
—
2
6
8
C
6C
Bowl Note 6)
+
—
d Drain port
Note 12)
J
Note 9)
W Note 13)
+
e
Flow direction
—
R
+
f
Pressure unit
—
Name plate and caution plate for bowl in imperial units: MPa
Z Note 10) Name plate and caution plate for bowl in imperial units: psi, °F
Note 1) Drain guide is NPT1/8 (applicable to the AFM20-A, AFD20-A) and NPT1/4 (applicable to the AFM30-A/40-A, AFD30-A/40-A).
The auto drain port comes with ø3/8" One-touch fitting (applicable to the AFM30-A/40-A, AFD30-A/40-A).
Note 2) Drain guide is G1/8 (applicable to the AFM20-A, AFD20-A) and G1/4 (applicable to the AFM30-A/40-A, AFD30-A/40-A).
Note 3) A bracket is not assembled and supplied loose at the time of shipment. Including 2 mounting screws
Note 4) When pressure is not applied, condensate which does not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending operations for the day is recommended.
Note 5) If the compressor is small (0.75 kW, discharge flow is less than 100 L/min [ANR]), air leakage from the drain cock may occur during start of operations. N.C. type is recommended.
Note 6) Refer to Chemical data on page 56 for chemical resistance of the bowl.
Note 7) A bowl guard is provided as standard equipment (polycarbonate).
Note 8) A bowl guard is provided as standard equipment (nylon).
Note 9) Without a valve function
Note 10) For pipe thread type: NPT.
Note 11) 앪: For pipe thread type: NPT only
Note 12) The combination of float type auto drain: C and D is not available.
Note 13) The combination of metal bowl: 2 and 8 is not available.
53
to AFM40-A
Micro Mist Separator Series AFD20-A to AFD40-A
Mist Separator
Series AFM20-A
Rated flow [L/min (ANR)] Note 1)
Drain capacity [cm3]
Bowl material
Bowl guard
Weight [kg]
1/4, 3/8, 1/2
3/4
Air
– 5 to 60°C (with no freezing)
1.5 MPa
1.0 MPa
0.05 MPa
0.3 μm (99.9% filtered particle size)
0.01 μm (99.9% filtered particle size)
MAX 1.0 mg/m3 (ANR) (≈ 0.8 ppm) Note 2) Note 3)
MAX 0.1 mg/m3 (ANR) (Before saturated with oil 0.01 mg/m3 (ANR) or less ≈ 0.008 ppm) Note 2) Note 3)
200
450
1100
120
240
600
8
25
45
Polycarbonate
Semi-standard (Steel)
Standard (Polycarbonate)
0.09
0.19
0.38
0.43
Note 1) Conditions: Inlet pressure: 0.7 MPa; The rated flow varies depending on the inlet pressure.
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side.
Note 2) When the compressor oil mist discharge concentration is 30 mg/m3 (ANR).
Note 3) Bowl seal and other O-rings are slightly lubricated.
Options/Part No.
Model
Bracket assembly Note 1)
Float type auto drain Note 2) Note 3)
N.C.
N.O.
AFM20-A
AFD20-A
AFM30-A
AFD30-A
AF22P-050AS
AD27-A
—
AF32P-050AS
AD37-A
AD38-A
AFM40-A
AFD40-A
AFM40-06-A
AFD40-06-A
AW AFM
Optional specifications
AF42P-050AS
AF42P-070AS
AD47-A
AD48-A
Note 1) Assembly of a bracket and 2 mounting screws
Note 2) Minimum operating pressure: N.O. type–0.1 MPa; N.C. type–0.1 MPa (AD27-A) and 0.15 MPa (AD37-A/AD47-A).
Please consult with SMC separately for psi and °F unit display specifications.
Note 3) Please consult with SMC for details on drain piping to fit NPT or G port sizes.
Bowl Assembly/Part No.
Model
With drain cock
Manual
Drain cock with barb fitting
discharge
With drain guide
Nylon bowl
(without valve function)
Automatic Note)
Normally closed (N.C.)
discharge
(Auto drain) Normally open (N.O.)
Metal bowl
With drain cock
Manual
discharge With drain guide
(without valve function)
Automatic Note) Normally closed (N.C.)
discharge
(Auto drain) Normally open (N.O.)
AFM30-A
AFD30-A
—
With bowl guard
With bowl guard
—
With bowl guard
—
With bowl guard
With bowl guard
—
With bowl guard
With bowl guard
—
With bowl guard
—
With bowl guard
With bowl guard
—
With level gauge
—
With level gauge
—
With level gauge
—
With level gauge
C2SF-A
C2SF-C-A
—
C2SF쏔-J-A
C2SF쏔-CJ-A
AD27-A
AD27-C-A
—
C2SF-6-A
C2SF-6C-A
—
C2SF쏔-6J-A
C2SF쏔-6CJ-A
AD27-6-A
AD27-6C-A
—
C2SF-2-A
—
C2SF쏔-2J-A
—
AD27-2-A
—
—
—
—
C3SF-A
C3SF-W-A
—
C3SF쏔-J-A
—
AD37쏔-A
AD38쏔-A
—
C3SF-6-A
C3SF-6W-A
—
C3SF쏔-6J-A
—
AD37쏔-6-A
AD38쏔-6-A
C3SF-2-A
C3LF-8-A
C3SF쏔-2J-A
C3LF쏔-8J-A
AD37쏔-2-A
AD37쏔-8-A
AD38쏔-2-A
AD38쏔-8-A
AFM40-A
AFD40-A
AFM40-06-A
AFD40-06-A
—
C4SF-A
C4SF-W-A
—
C4SF쏔-J-A
—
AD47쏔-A
AD48쏔-A
—
C4SF-6-A
C4SF-6W-A
—
C4SF쏔-6J-A
—
AD47쏔-6-A
AD48쏔-6-A
C4SF-2-A
C4LF-8-A
C4SF쏔-2J-A
C4LF쏔-8J-A
AD47쏔-2-A
AD47쏔-8-A
AD48쏔-2-A
AD48쏔-8-A
AF
Manual
Drain cock with barb fitting
discharge
Polycarbonate
With drain guide
bowl
(without valve function)
Automatic Note)
Normally closed (N.C.)
discharge
(Auto drain) Normally open (N.O.)
AFM20-A
AFD20-A
AFM / AFD
With drain cock
Other
AR
Drain port
AL
Drain
discharge
mechanism
AW
Bowl
material
AF AR AL
1/4, 3/8
AFM40-06-A
AFD40-06-A
AW AL
Outlet side oil mist
concentration
AFM20-A to AFM40-06-A
AFD20-A to AFD40-06-A
AFM20-A to AFM40-06-A
AFD20-A to AFD40-06-A
AFM20-A to AFM40-06-A
AFD20-A to AFD40-06-A
1/8, 1/4
AFM40-A
AFD40-A
AF AR
Nominal filtration rating
AFM30-A
AFD30-A
AF AFM AR
Port size
Fluid
Ambient and fluid temperature
Proof pressure
Maximum operating pressure
Minimum operating pressure
AFM20-A
AFD20-A
Attachment
Model
AC
Standard Specifications
Note) Minimum operating pressure: N.O. type–0.1 MPa (AD38-A, AD48-A); N.C. type–0.1 MPa (AD17-A, AD27-A) and 0.15 MPa (AD37-A, AD47-A).
Bowl assembly for the AFM20-A to AFM40-06-A, AFD20-A to AFD40-06-A models comes with a bowl seal.
쏔 in bowl assembly part numbers indicates a pipe thread type (applicable tubing for auto drain). No indication is necessary for Rc thread; however, indicate N for
NPT thread, and F for G thread. (For auto drain, —: ø10, N: ø3/8")
Please consult with SMC separately for psi and °F unit display specifications.
54
Series AFM20-A
to AFM40-A
Series AFD20-A to AFD40-A
When saturated with oil
Initial state
Flow-rate Characteristics (Representative values)
AFM20-A
AFD20-A
a
0.04
0.04
a
Pa
0.03
.3
.5
M
P
=0
0
1=
a
MP
0.7
MP
Pressure drop [MPa]
Pressure drop [MPa]
P
P1=
P1
0.02
a
P1
0.01
.3
=0
Pa
MP
.5 M
0
P1=
0.7
P1=
.3
=0
MP
a
MP
0.02
0.3
P1=
0.01
50
100
150
MP
a
MP
0.5
P1=
Pa
.7 M
P1=0
50
0
200
100
Flow rate L/min (ANR)
Flow rate L/min (ANR)
AFM30-A
AFD30-A
M
0.5
P1=
=0
P1
Pressure drop [MPa]
.3
0.03
a
MP
0.7
P1=
0.02
Pa
0.01
P1
Pa
5M
0.
P1=
M
0.3
=
0.7
P1=
P1
Pa
Pa
M
0.
P1=
a
MP
.3
=0
Pa
5M
0.04
0.04
Pressure drop [MPa]
0.7
P1=
0
0
0.02
Pa
3M
0.
P 1=
Pa
.7 M
P1=0
a
MP
0.03
0.01
0
Pa
5M
0.
P1=
P1=0.7
MPa
0
0
100
200
300
400
500
0
600
50
100
Flow rate L/min (ANR)
200
AFD40-A
.3
P1
0.03
=0
.5
P1
=0
a
MP
a
0.3
P1=
a
MP
Pa
.5 M
0
P1=
P1=0.7
MPa
0
200
400
600
800
Flow rate L/min (ANR)
3
0.
0.5
M
MP
P1=
=
MPa
0.7
P1=
0
P1=
0.02
0.01
P1
P
.7 M
Pressure drop [MPa]
Pa
M
a
Pa
0.04
0.04
0
150
Flow rate L/min (ANR)
AFM40-A
Pressure drop [MPa]
MP
0.03
a
MPa
0
55
a
0.5
P1=
1
1000
0.03
0.02
Pa
3M
=0.
0.01
P1
0
0
100
200
0.5
P1=
a
MP
300
Pa
.7 M
P1=0
400
Flow rate L/min (ANR)
500
600
to AFM40-A
Micro Mist Separator Series AFD20-A to AFD40-A
Series AFM20-A
Air Supply
Caution
Warning
1. The standard bowl for the air filter, filter regulator,
and lubricator, as well as the sight dome for the
lubricator are made of polycarbonate. Do not use in
an environment where they are exposed to or come
in contact with organic solvents, chemicals, cutting
oil, synthetic oil, alkali, and thread lock solutions.
1. Install an air filter (Series AF) as a pre-filter on the inlet side of
the mist separator to prevent premature clogging.
2. Install a mist separator (Series AFM) as a pre-filter on the inlet
side of the micro mist separator to prevent premature clogging.
3. Do not install on the inlet side of the dryer as this can cause
premature clogging of the element.
Effects of atmosphere of organic solvents and chemicals, and
where these elements are likely to adhere to the equipment.
Chemical data for substances causing degradation (Reference)
Maintenance
Material
Aromatic
series
Ketone
Alcohol
Oil
Gasoline
Kerosene
Degreasing of metals
Industrial salts
Water-soluble
cutting oil
҂
҂
—
҂
왕
Cleansing liquid for metals
Printing ink
Dilution
҂
왕
Coatings
Dry cleaning
҂
왕
Photographic film
Dry cleaning
Textile industries
҂
҂
Antifreeze
Adhesives
왕
҂
҂
쑗
—
Caution
1. When the bowl is installed on the
mist separator (AFM30-A/AFM40A), or micro mist separator (AFD30A/AFD40-A), install them so that the
lock button lines up to the groove of
the front (or the back) of the body to
avoid drop or damage of the bowl.
Lock button
Attachment
쑗
AW AFM
Mounting/Adjustment
Design
Caution
Phthalic acid dimethyl
Synthetic oil
Phthalic acid diethyl
҂
쑗
Anti-rust additives
Acetic acid
Methyl ether
Brake oil additives
Ether
҂
쑗
Ethyl ether
Cutting oil
Amino
Methyl amino
Brake oil additives
҂
҂
Rubber accelerator
Thread-lock fluid
Others
Seawater
—
҂
왕
Leak tester
쑗: Essentially safe 왕: Some effects may occur. ҂: Effects will occur.
Ester
When the above factors are present, or there is some doubt, use a metal bowl
for safety.
1. Design the system so that the mist separator is installed in a
pulsation-free location. The difference between internal and
external pressure inside the element should be kept within 0.1
MPa, as exceeding this value could cause damage.
Selection
AF
Chlorine
solvents
왕
AFM / AFD
Inorganic
salts
Acid washing liquid
for metals
Nylon
Caution
1. Do not allow air flow that exceeds the rated flow. If the air flow
is allowed outside the range of the rated flow even momentarily, drainage and lubricant may splash at the outlet side or
cause damage to the component.
2. Do not use in a low pressure application (such as a blower). An
F.R.L. unit has its own minimum operating pressure depending
on the equipment and is designed specifically to function with
compressed air. If used below the minimum operating pressure, a loss of performance and malfunction can occur. Please
contact SMC if an application under such conditions cannot be
avoided.
56
AR
Alkaline
Hydrochloric acid
Sulfuric acid, Phosphoric acid
Chromic acid
Sodium hydroxide (Caustic soda)
Potash
Calcium hydroxide (Slack lime)
Ammonia water
Carbonate of soda
Sodium sulfide
Sulfate of potash
Sulfate of soda
Carbon tetrachloride
Chloroform
Ethylene chloride
Methylene chloride
Benzene
Toluene
Paint thinner
Acetone
Methyl ethyl ketone
Cyclohexane
Ethyl alcohol
IPA
Methyl alcohol
Application examples Polycarbonate
AL
Acid
Chemical name
AW
Type
Warning
1. Replace the element every 2 years or when the pressure drop
becomes 0.1 MPa, whichever comes first, to prevent damage
to the element.
AW AL
Design/Selection
AF AR
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
AF AR AL
AC
Specific Product Precautions
AF AFM AR
Mist Separator
Series AFM20-A
to AFM40-A
Series AFD20-A to AFD40-A
Construction
AFM30-A to AFM40-06-A
AFD30-A to AFD40-06-A
AFM20-A
AFD20-A
IN
IN
OUT
OUT
:
:
.
.
@
@
;
;
Drain
Drain
Component Parts
No.
1
Description
Body
Material
Model
Colour
Aluminium die-cast
AFM20-A to AFM40-06-A
AFD20-A to AFD40-06-A
White
Replacement Parts
Part no.
No.
Description
2
Element assembly
3
Bowl seal
4
Bowl assembly Note)
Material
AFM20-A
AFD20-A
AFM30-A
AFD30-A
AFM20 to 40
—
AFM20P-060AS
AFM30P-060AS
AFM40P-060AS
AFD20 to 40
—
AFD20P-060AS
AFD30P-060AS
AFD40P-060AS
NBR
C2SFP-260S
C32FP-260S
C42FP-260S
Polycarbonate
C2SF-A
C3SF-A
C4SF-A
AFM40-A
AFD40-A
Note) Bowl seal is included. Please contact SMC regarding the supply of bowl assembly with psi and °F unit display specifications.
57
AFM40-06-A
AFD40-06-A
AFM20-A to AFM40-A
Micro Mist Separator Series AFD20-A to AFD40-A
Mist Separator
Series
Dimensions
U
S
AF AR AL
D
S
N
C
V
Q
IN
OUT
OUT
With drain guide
Metal bowl
Metal bowl with drain guide
With auto drain (N.O./N.C.)
M5 x 0.8
Width
across
flats 14
1/8
1/8
B
Thread type/Rc, G:
ø10 One-touch fitting
Thread type/NPT:
ø3/8" One-touch fitting
AFM30-A to AFM40-06-A /AFD30-A to AFD40-06-A
With drain guide
Drain cock with barb fitting
Width
across
flats 17
Width
across
flats 17
1/4
Barb fitting
applicable
tubing:
T0604
1/4
AR
1/4
B
B
Width
across
flats 17
Dimensions
Metal bowl with level gauge,
with drain guide
B
Metal bowl
with level gauge
B
Metal bowl with drain guide
B
Metal bowl
B
Applicable model
Optional/Semi-standard
specifications
B
Width
across
flats 14
Dimensions
B
B
B
N.O.: Black
N.C.: Grey
Attachment
With auto drain (N.C.)
AFM30-A to AFM40-06-A/AFD30-A to AFD40-06-A
AW AFM
A
AF AFM AR
AF AR
B
Drain
G
E
AFM20-A /AFD20-A
Applicable model
Clearance for
maintenance
A
G
Clearance for
maintenance
Drain
Optional/Semi-standard
specifications
2xP
(Port size)
B
2xP
(Port size)
AW AL
Bracket
(Option)
AF
IN
AFM / AFD
Bracket
(Option)
T
M
C
U
J
R
T
N
R
M
D
Q
V
J
AC
AFM30-A to AFM40-06-A
AFD30-A to AFD40-06-A
AFM20-A
AFD20-A
AFM20-A/AFD20-A
AFM30-A/AFD30-A
AFM40-A/AFD40-A
AFM40-06-A/AFD40-06-A
B
C
D
E
G
J
M
N
Q
R
S
T
U
V
B
40
53
70
75
87.6
115.1
147.1
149.1
9.8
14
18
20
20
26.7
35.5
35.5
—
30
38.4
38.4
40
50
75
75
20
26.7
35.5
35.5
30
41
50
50
27
40
54
54
22
23
26
25
5.4
6.5
8.5
8.5
8.4
8
10.5
10.5
40
53
70
70
2.3
2.3
2.3
2.3
28
30
35
34
104.9
156.8
186.9
188.9
Semi-standard specifications
Metal bowl with drain guide
Metal bowl with level gauge
With barb fitting
With drain guide
Metal bowl
B
B
B
B
B
Metal bowl with level gauge, with drain guide
B
—
123.6
155.6
157.6
91.4
121.9
153.9
155.9
87.4
117.6
149.6
151.6
93.9
122.1
154.1
156.1
—
137.6
169.6
171.6
—
142.1
174.1
176.1
58
AL
1/8, 1/4
AFM20-A/AFD20-A
1/4, 3/8
AFM30-A/AFD30-A
AFM40-A/AFD40-A 1/4, 3/8, 1/2
3/4
AFM40-06-A/AFD40-06-A
With auto drain
A
AW
P
Model
Optional specifications
Bracket mount
Standard specifications
Model
Mist Separator/AFM20-A to AFM40-06-A
Micro Mist Separator/AFD20-A to AFD40-06-A
Made to Order
Please contact SMC for detailed dimensions, specifications and lead times.
q Long Bowl
Drain capacity is greater than that of standard models.
Applicable Model/Drain Capacity
AFM20-A, AFD20-A AFM30-A, AFD30-A AFM40-A, AFD40-A
Model
Port size
1/8, 1/4
1/4, 3/8
Drain capacity [cm3]
19
43
AFM40-06-A, AFD40-06-A
1/4, 3/8, 1/2
3/4
88
Note) Please consult with SMC for dimensions.
AFM 30
03
A X64
AFD 30
03
A X64
q
w
e
r
t
• Semi-standard: Select one each for a to d.
• Option/Semi-standard symbol: When more than one specification is
required, indicate in alphanumeric order.
Example) AFM30-03B-2R-A-X64
Long bowl
q
Symbol
w
Pipe thread type
—
N Note 1)
F Note 2)
Port size
01
02
03
04
06
Description
20
30
40
Rc
NPT
G
앬
앬
앬
앬
앬
앬
앬
앬
앬
1/8
1/4
3/8
1/2
3/4
앬
앬
—
—
—
—
앬
앬
—
—
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
Polycarbonate bowl
Metal bowl
Nylon bowl
With bowl guard
With bowl guard (Nylon bowl)
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
— Note 5)
— Note 6)
— Note 5)
— Note 6)
With drain cock
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting (for ø6 x ø4 nylon tube)
앬
앬
—
—
앬
—
앬
앬
앬
—
앬
앬
Flow direction: Left to right
Flow direction: Right to left
앬
앬
앬
앬
앬
앬
앬
앪 Note 10)
앬
앪 Note 10)
앬
앪 Note 10)
+
e
Body size
+
r
Option (Mounting)
—
Without mounting option
B Note 3) With bracket
+
t
Semi-standard
a
Bowl Note 4)
—
2
6
C
6C
+
—
b
Drain port
J Note 7)
W Note 8)
+
c
Flow direction
—
R
+
d
Pressure unit
—
Name plate and caution plate for bowl in imperial units: MPa
Z Note 9) Name plate and caution plate for bowl in imperial units: psi, °F
Note 1) Drain guide is NPT1/8 (applicable to the AFM20-A, AFD20-A) and NPT1/4 (applicable to the AFM30-A/40-A, AFD30-A/40-A).
Note 2) Drain guide is G1/8 (applicable to the AFM20-A, AFD20-A) and G1/4 (applicable to the AFM30-A/40-A, AFD30-A/40-A).
Note 3) A bracket is not assembled and supplied loose at the time of shipment. Including 2 mounting screws.
Note 4) Refer to Chemical data on page 56 for chemical resistance of the bowl.
Note 5) A bowl guard is provided as standard equipment (polycarbonate).
Note 6) A bowl guard is provided as standard equipment (nylon).
Note 7) Without a valve function
Note 8) The combination of metal bowl: 2 is not available.
Note 9) For pipe thread type: NPT.
Note 10) 앪: For pipe thread type: NPT only
59
Mist Separator/AFM20-A to AFM40-06-A
Micro Mist Separator/AFD20-A to AFD40-06-A
Made to Order
AC
Please contact SMC for detailed dimensions, specifications and lead times.
w With Element Service Indicator
Applicable Model
Model
AFM20-A, AFD20-A
AFM30-A, AFD30-A
AFM40-A, AFD40-A
AFM40-06-A, AFD40-06-A
Port size
1/8, 1/4
1/4, 3/8
1/4, 3/8, 1/2
3/4
AFD 30
03
A X2141
q
w
e
r
t
• Option/Semi-standard: Select one each for a to f.
• Option/Semi-standard symbol: When more than one specification is
required, indicate in alphanumeric order.
Example) AFM30-03BD-2R-A-X2141
AF AR
A X2141
With element service indicator
A special body type is required to mount the element service indicator. It cannot be mounted on a standard body.
20
30
40
Pipe thread type
—
N Note 1)
F Note 2)
Rc
NPT
G
앬
앬
앬
앬
앬
앬
앬
앬
앬
Port size
01
02
03
04
06
1/8
1/4
3/8
1/2
3/4
앬
앬
—
—
—
—
앬
앬
—
—
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
—
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
앬
r
Option
a
Mounting
Without mounting option
B Note 3) With bracket
+
b
Float type
auto drain
—
Without auto drain
C Note 4) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 5) N.O. (Normally open) Drain port is open when pressure is not applied.
+
t
Semi-standard
c
Bowl Note 6)
—
2
6
8
C
6C
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
With bowl guard (Nylon bowl)
앬
앬
앬
—
앬
앬
— Note 7)
— Note 8)
— Note 7)
— Note 8)
—
With drain cock
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting (for ø6 x ø4 nylon tube)
앬
앬
—
—
앬
—
앬
앬
앬
—
앬
앬
—
R
Flow direction: Left to right
Flow direction: Right to left
앬
앬
앬
앬
앬
앬
—
Name plate and caution plate for bowl in imperial units: MPa
앬
앪 Note 11)
앬
앪 Note 11)
앬
앪 Note 11)
+
d Drain port
Note 12)
J
Note 9)
W Note 13)
+
e
Flow direction
+
f
Pressure unit
Z Note 10) Name plate and caution plate for bowl in imperial units: psi, °F
Note 1) Drain guide is NPT1/8 (applicable to the AFM20-A, AFD20-A) and NPT1/4
(applicable to the AFM30-A/40-A, AFD30-A/40-A).
The auto drain port comes with ø3/8" One-touch fitting (applicable to the
AFM30-A/40-A, AFD30-A/40-A).
Note 2) Drain guide is G1/8 (applicable to the AFM20-A, AFD20-A) and G1/4
(applicable to the AFM30-A/40-A, AFD30-A/40-A).
Note 3) A bracket is not assembled and supplied loose at the time of shipment.
Including 2 mounting screws
Note 4) When pressure is not applied, condensate which does not start the auto
drain mechanism will be left in the bowl. Releasing the residual
condensate before ending operations for the day is recommended.
Attachment
+
—
AF
e
AFM / AFD
+
AW AFM
Body size
AR
w
Description
AF AFM AR
q
Symbol
Note 5) If the compressor is small (0.75 kW, discharge flow is less than 100 L/min
[ANR]), air leakage from the drain cock may occur during start of operations.
N.C. type is recommended.
Note 6) Refer to Chemical data on page 56 for chemical resistance of the bowl.
Note 7) A bowl guard is provided as standard equipment (polycarbonate).
Note 8) A bowl guard is provided as standard equipment (nylon).
Note 9) Without a valve function
Note 10) For pipe thread type: NPT.
Note 11) 앪: For pipe thread type: NPT only
Note 12) The combination of float type auto drain: C and D is not available.
Note 13) The combination of metal bowl: 2 and 8 is not available.
60
AL
03
AW
AFM 30
AW AL
AF AR AL
Clogging status of elements can be checked visually.
61
Modular Type
Regulator
AF + AR + AL
Set pressure
Options
Bracket
AR10-A
M5 x 0.8
0.05 to 0.7 MPa
0.02 to 0.2 MPa
Round type pressure gauge
1/8, 1/4
Bracket
AR25(K)-B
AF + AFM + AR
AR20(K)-B
AF + AR
Set nut (for panel mount) ∗
Set nut (for panel mount)
1/4, 3/8
1/4, 3/8, 1/2
0.05 to 0.85 MPa
0.02 to 0.2 MPa
AW + AFM
Square embedded type
pressure gauge
AR30(K)-B
AR40(K)-B
Digital pressure switch
Round type pressure gauge
AR60(K)-B
1
Square embedded type
pressure gauge
Digital pressure switch
Round type pressure gauge
∗ Interchangeable with existing AR series
AR
3/4, 1
AF
Bracket
AR50(K)-B
AL
P.63 to 74
3/4
AW
AR40(K)-06-B
AW + AL
Port size
Attachment
Model
AFM / AFD
Regulator
Series AR
AC
Series AR
62
Regulator
AR10-A
Symbol
Regulator
1
2
AR10-A
How to Order
AR10 M5
• Option/Semi-standard: Select one each for a to g.
• Option/Semi-standard symbol: When more than one specification is required,
indicate in alphanumeric order.
Example) AR10-M5BG-1NR-A
A
q
w
q
앬
Option Note 1)
Symbol
a
Mounting
B
Refer to page 65 for size 20 to 60.
Description
—
Without mounting option
Note 2)
With bracket
H
With set nut (for panel mount)
+
b
Pressure gauge
G
—
Without pressure gauge
Note 3)
Round type pressure gauge (without limit indicator)
+
c
Set pressure Note 4)
—
0.05 to 0.7 MPa setting
1
0.02 to 0.2 MPa setting
+
w
앬
Semi-standard
d
Exhaust mechanism
—
Relieving type
N
Non-relieving type
+
e
Flow direction
—
Flow direction: Left to right
R
Flow direction: Right to left
+
f
Knob
—
Downward
Y
Upward
+
g
Pressure unit
—
Name plate and pressure gauge in imperial units: MPa
Z
Name plate and pressure gauge in imperial units: psi
Note 1) Options are not assembled and supplied loose at the time of shipment.
Note 2) Assembly of a bracket and set nuts
Note 3) A 1.0 MPa pressure gauge will be fitted. It is not assembled and supplied loose at the time of shipment.
Note 4) Pressure can be set higher than the specification pressure in some cases, but use pressure within the specification range.
63
Regulator
Series AR10-A
Port size
AC
Standard Specifications
M5 x 0.8
Pressure gauge port size Note)
1/16
Air
Ambient and fluid temperature
AF AR AL
Fluid
–5 to 60°C (with no freezing)
Proof pressure
1.5 MPa
Maximum operating pressure
1.0 MPa
Set pressure range
0.05 to 0.7 MPa
Relieving type
Weight [kg]
AW AL
Construction
0.06
AF AR
Note) Use a bushing (part no.: 131368) when connecting the R1/8 pressure gauge to the Rc1/16.
Options/Part No.
Bracket assembly Note 1)
AR12P-270AS
Mounting/Adjustment
1. Although exhaust of the residual pressure to the inlet side is
possible when eliminating the inlet pressure, exhaust is not
possible when the set pressure is 0.15 MPa or less.
1. Set the regulator while verifying the displayed values of the inlet and outlet pressure gauges. Turning the regulator knob excessively can cause damage to the internal parts.
2. Do not use tools on the pressure regulator knob as this may
cause damage. It must be operated manually.
Warning
Warning
Maintenance
Warning
1. When using the regulator between a solenoid valve and an actuator, check the pressure gauge periodically. Sudden pressure fluctuations may shorten the durability of the pressure
gauge. A digital pressure gauge is recommended for such
situation or as deemed necessary.
Caution
1. Be sure to unlock the knob before adjusting the pressure and lock
it after setting the pressure. Failure to follow this procedure can
cause damage to the knob and the outlet pressure may fluctuate.
• Pull the pressure regulator knob to unlock. (You can visually
verify this with the “orange mark” that appears in the gap.)
• Push the pressure regulator knob to lock. When the knob is not
easily locked, turn it left and right a little and then push it (when
the knob is locked, the “orange mark”, i.e., the gap will disappear).
2. Pulsation will be generated when the difference between the
inlet and the outlet pressure is large. In this case, reduce the
pressure difference between the inlet and the outlet. Please
consult with SMC if the pulsation problem is not resolved.
64
AW AFM
Attachment
Selection
AF
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
AFM / AFD
Specific Product Precautions
AR
G27-10-R1
Note 1) Assembly of a bracket and set nuts
Note 2) 1.0 MPa pressure gauge
AL
Round type pressure gauge
AF AFM AR
AR12P-260S
Note 2)
AW
Set nut
Regulator
Symbol
AR20-B to AR60-B
Regulator with Backflow Function
AR20K-B to AR60K-B
Regulator with
Backflow Function
Regulator
1
2
1
2
• With the backflow function it incorporates a mechanism to exhaust the air pressure in
the outlet side reliably and quickly.
Example 1)
When the pressure in the rear and
the front of the cylinder differs:
1
2
1
14 2
4
12
31 5
q
w
03 BE
e
r
t
B
y
1
L
2 1
3
2 1
2
10
Refer to page 63 for size 10.
How to Order
AR 30 K
12
Example 2)
When the air supply is cut off and
releasing the inlet pressure to the
atmosphere, the residual pressure
release of the outlet side can be
ensured for a safety purpose.
1
• Option/Semi-standard: Select one each for a to g.
• Option/Semi-standard symbol: When more than one
specification is required, indicate in alphanumeric order.
Example) AR30K-03BE-1NR-B
q
앬
Symbol
Description
With backflow
function
—
K Note 1)
Without backflow function
With backflow function
Pipe thread type
—
N
F
Port size
01
02
03
04
06
10
Body size
20
w
앬
25
30
40
—
—
—
50
60
+
e
앬
Rc
NPT
G
+
r
앬
1/8
1/4
3/8
1/2
3/4
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
+
a
Mounting
Without mounting option
—
B Note 3) With bracket
With set nut (for panel mount)
H
t
앬
Option Note 2)
+
Pressure
gauge Note 4)
b
Digital
pressure
switch Note 5)
65
—
E
G
M
E1
E2
E3
E4
Without pressure gauge
Square embedded type pressure gauge (with limit indicator)
Round type pressure gauge (with limit indicator)
Round type pressure gauge (with colour zone)
Output: NPN output/Electrical entry: Wiring bottom entry
Output: NPN output/Electrical entry: Wiring top entry
Output: PNP output/Electrical entry: Wiring bottom entry
Output: PNP output/Electrical entry: Wiring top entry
—
—
to AR60-B
Regulator with Backflow Function Series AR20K-B to AR60K-B
Series AR20-B
AF AR AL
AC
Regulator
AR40-B, AR40K-B
q
앬
Description
Body size
20
d
Exhaust
mechanism
—
N
Flow direction
—
R
Knob
—
Y
50
60
Relieving type
Non-relieving type
AW AFM
y
앬
Semi-standard
+
+
e
Flow direction: Left to right
Flow direction: Right to left
+
f
Downward
Upward
+
—
g
Pressure unit
Name plate and pressure gauge in imperial units: MPa
Z Note 7) Name plate and pressure gauge in imperial units: psi
ZA Note 8) Digital pressure switch: With unit conversion function
Note 1) Set the inlet pressure to at least 0.05 MPa higher than the set pressure.
Note 2) Option B, G, H, M are not assembled and supplied loose at the time of
shipment.
Note 3) Assembly of a bracket and set nuts (applicable to the AR20(K)-B to
AR40(K)-B). Including 2 mounting screws for the AR50(K)-B and AR60(K)-B
Note 4) When the pressure gauge is attached, a 1.0 MPa pressure gauge will be fitted
for standard (0.85 MPa) type. 0.4 MPa pressure gauge for 0.2 MPa type.
Note 5) When choosing with H (panel mount), the installation space for lead wires will
not be secured. In this case, select “wiring top entry” for the electrical entry.
(Select “wiring bottom entry” when the semi-standard Y is chosen
simultaneously.)
Note 6) Pressure can be set higher than the specification pressure in some cases, but
Note 9)
Note 9)
Note 9)
Note 9)
Note 9)
Note 9)
Note 10)
Note 10)
Note 10)
Note 10)
Note 10)
Note 10)
use pressure within the specification range.
Note 7) For pipe thread type: NPT.
Cannot be used with M: Round pressure gauge (with colour zone). Available
by request for special.
The digital pressure switch will be equipped with the unit conversion function,
setting to psi initially.
Note 8) For options: E1, E2, E3, E4.
Note 9) 앪: For pipe thread type: NPT only
Note 10) 왕: Select with options: E1, E2, E3, E4.
Standard Specifications
AR25-B
AR30-B
1/8, 1/4
1/4, 3/8
1/4, 3/8
0.16
0.21
AR40-B
AR40-06-B
1/4, 3/8, 1/2
3/4
1/8
Air
–5 to 60°C (with no freezing)
1.5 MPa
1.0 MPa
0.05 to 0.85 MPa
Relieving type
0.29
0.44
0.47
AR50-B
AR60-B
3/4, 1
1
1.17
1.22
AL
AR20-B
AW
Model
Port size
Pressure gauge port size Note 1)
Fluid
Ambient and fluid temperature Note 2)
Proof pressure
Maximum operating pressure
Set pressure range
Construction
Weight [kg]
Attachment
—
1
40
AF
Set
pressure Note 6)
30
AFM / AFD
c
25
0.05 to 0.85 MPa setting
0.02 to 0.2 MPa setting
AR
Symbol
AF AFM AR
AF AR
AW AL
AR20-B, AR20K-B
Note 1) Pressure gauge connection threads are not available for F.R.L. unit with a square embedded type pressure gauge or with a digital pressure switch.
Note 2) –5 to 50°C for the products with the digital pressure switch
66
Series AR20-B
to AR60-B
Series AR20K-B to AR60K-B
Options/Part No.
Model
Option
AR20(K)-B
AR25(K)-B
AR30(K)-B
AR40(K)-B
AR40(K)-06-B
AR50(K)-B
AR60(K)-B
Bracket assembly Note 1)
AR23P-270AS AR28P-270AS AR33P-270AS
AR43P-270AS
AR52P-270AS
Set nut
AR23P-260S AR28P-260S AR33P-260S
AR43P-260S
— Note 2)
Standard
G36-10-첸01
G46-10-첸01
Round
type Note 3) 0.02 to 0.2 MPa setting
G36-4-첸01
G46-4-첸01
Standard
G36-10-첸01-L
G46-10-첸01-L
Pressure Round type Note 3)
gauge (with colour zone) 0.02 to 0.2 MPa setting
G36-4-첸01-L
G46-4-첸01-L
Standard
GC3-10AS [GC3P-010AS (Pressure gauge cover only)]
Square Note 4)
embedded type 0.02 to 0.2 MPa setting
GC3-4AS [GC3P-010AS (Pressure gauge cover only)]
NPN output: Wiring bottom entry
ISE35-N-25-MLA [ISE35-N-25-M (Switch body only)]
Digital
NPN output: Wiring top entry
ISE35-R-25-MLA [ISE35-R-25-M (Switch body only)]
pressure
PNP output: Wiring bottom entry
ISE35-N-65-MLA [ISE35-N-65-M (Switch body only)]
Note 5)
switch
PNP output: Wiring top entry
ISE35-R-65-MLA [ISE35-R-65-M (Switch body only)]
Note 1) Assembly of a bracket and set nuts. Including 2 mounting screws for the AR50(K)-B and AR60(K)-B
Note 2) Please consult with SMC regarding the set nuts for the AR50(K)-B and AR60(K)-B.
Note 3) 첸 in part numbers for a round pressure gauge indicates a pipe thread type. No indication is necessary for R; however, indicate N for NPT.
Please contact SMC regarding the pressure gauge supply for psi unit specifications.
Note 4) Including one O-ring and 2 mounting screws. [ ]: Pressure gauge cover only
Note 5) In addition to the pressure switch body, lead wire with connector (2 m), adapter, lock pin, O-ring (1 pc.), mounting screw (2 pcs.) are attached.
[ ]: Switch body only. (Regarding how to order the digital pressure switch, please consult with SMC.
Specific Product Precautions
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
Selection
Mounting/Adjustment
1. Residual pressure disposal (outlet pressure removal) is not
possible for the AR20-B to AR60-B even though the inlet
pressure is exhausted. When the residual pressure disposal is
performed, use the regulator with a backflow function
(AR20K-B to AR60K-B).
1. Set the regulator while verifying the displayed values of the
inlet and outlet pressure gauges. Turning the regulator knob
excessively can cause damage to the internal parts.
2. Do not use tools on the pressure regulator knob as this may
cause damage. It must be operated manually.
Warning
Warning
Maintenance
Warning
1. When using the regulator with backflow function between a
solenoid valve and an actuator, check the pressure gauge
periodically. Sudden pressure fluctuations may shorten the
durability of the pressure gauge. A digital pressure gauge is
recommended for such situation or as deemed necessary.
Caution
1. Be sure to unlock the knob before adjusting the pressure and
lock it after setting the pressure. Failure to follow this procedure
can cause damage to the knob and the outlet pressure may
fluctuate.
• Pull the pressure regulator knob to unlock. (You can visually
verify this with the “orange mark” that appears in the gap.)
• Push the pressure regulator knob to lock. When the knob is
not easily locked, turn it left and right a little and then push it
(when the knob is locked, the “orange mark”, i.e., the gap will
disappear).
Orange mark
2. A knob cover is available to prevent careless operation of the
knob. Refer to page 97 for details.
67
AR10-A
Regulator Series AR20-B to AR60-B
Regulator with Backflow Function Series AR20K-B to AR60K-B
Series
Regulator
Flow-rate Characteristics (Representative values)
0.2
0.3
0.2
50
75
100
125
0
0
150
200
0.2
400
600
0
0
800
Rc3/8
AR40(K)-B
Rc1/2
0.5
0.5
0.5
0.2
0.1
0.4
0.3
0.2
500
1000
0
0
1500
Rc1
2000
AR60(K)-B
0.6
0.5
0.5
Outlet pressure [MPa]
0.6
0.4
0.3
0.2
0.1
Rc3/4
0.4
0.3
3000
0
0
1000
2000
3000
4000
5000
Flow rate L/min (ANR)
Rc1
0.4
0.3
0.2
0
5000
10000
Flow rate L/min (ANR)
AR
0
AL
Flow rate L/min (ANR)
10000
AW
5000
AFM / AFD
0.1
0
AC
0.2
AF
AR50(K)-B
1000
Flow rate L/min (ANR)
Flow rate L/min (ANR)
1500
0.1
0.1
0
0
0
Outlet pressure [MPa]
0.6
Outlet pressure [MPa]
0.6
0.3
1000
AR40(K)-06-B
0.6
0.4
500
Flow rate L/min (ANR)
Flow rate L/min (ANR)
Flow rate L/min (ANR)
AR30(K)-B
0.3
0.1
0.1
25
0.4
AF AR
0.3
0.4
AF AFM AR
0.4
AF AR AL
0.5
Rc3/8
AW AL
0.5
Outlet pressure [MPa]
0.5
0
0
Outlet pressure [MPa]
AR25(K)-B
0.6
0.1
Outlet pressure [MPa]
Rc1/4
0.6
AW AFM
AR20(K)-B
Attachment
M5
0.6
Outlet pressure [MPa]
Outlet pressure [MPa]
AR10-A
Condition: Inlet pressure 0.7 MPa
68
Series
Series
Series
AR10-A
AR20-B to AR60-B
AR20K-B to AR60K-B
Pressure Characteristics (Representative values)
AR10-A
Conditions: Inlet pressure 0.7 MPa, Outlet pressure 0.2 MPa, Flow rate 20 L/min (ANR)
AR20(K)-B
AR25(K)-B
0.3
Set point
0.2
0.15
0.25
Set point
0.2
Outlet pressure [MPa]
0.25
Outlet pressure [MPa]
Outlet pressure [MPa]
0.25
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0
0
1
0.2
0.3
AR30(K)-B
0.8
0.9
0
0
1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
Set point
0.2
0
0
1
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
0.2
0.15
Outlet pressure [MPa]
0.25
Set point
Set point
0.2
0.15
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
0.9
1
0
0
0.5
0.6
0.7
0.8
0.9
1
Set point
0.2
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
0
0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
AR60(K)-B
0.25
0.4
0.15
0.2
Inlet pressure [MPa]
AR50(K)-B
0.2
0.3
AR40(K)-06-B
0.15
0.2
0.2
Inlet pressure [MPa]
Outlet pressure [MPa]
Set point
Outlet pressure [MPa]
Outlet pressure [MPa]
0.7
0.25
Inlet pressure [MPa]
Outlet pressure [MPa]
0.6
0.25
0.15
69
0.5
AR40(K)-B
0.25
0
0
0.4
Inlet pressure (MPa)
Inlet pressure [MPa]
0
0
0.2
0.15
0.15
0
0
Set point
0.9
1
0.9
1
AR10-A
Regulator Series AR20-B to AR60-B
Regulator with Backflow Function Series AR20K-B to AR60K-B
Regulator
Series
Construction
t
IN
OUT
r
q
AR20(K)-B/AR25(K)-B
AC
e
q
t
e
IN
OUT
r
w
AF + AR + AL
AR10-A
AW + AL
w
AR30(K)-B/AR40(K)-B
AF + AR
y
y
q
t
OUT
r
w
t
q
e
IN
OUT
r
w
AW + AFM
IN
AF + AFM + AR
AR50(K)-B/AR60(K)-B
e
Attachment
y
Component Parts
No.
1
Description
Body
Material
Model
Zinc die-cast
AR10-A
Aluminium die-cast
AR20(K)-B to
AR60(K)-B
Colour
y
White
Aluminium die-cast
White
AR50(K)-B/
AR60(K)-B
AR20K-B to AR60K-B
(Regulator with Backflow Function)
Replacement Parts
[AR10-A]
Part no.
3
Valve
HNBR
AR10P-090S
1
4
Piston assembly
Polyacetal
AR10P-150AS
IN
5
Valve guide assembly
Polyacetal
131329
6
Knob
Polyacetal
AR12P-030
SMC
Description
3
Valve
Material
Brass, HNBR
AL
A
[AR20(K)-B to AR60(K)-B]
No.
AR
Material
u
OUT
Description
A-A
A
2
No.
AFM / AFD
Bonnet
Part no.
AR20(K)-B
AR25(K)-B
AR30(K)-B
AR20P-410S
AR25P-410S
AR30P-410S
AR40(K)-B
AR40(K)-06-B
AR40P-410S
AR50(K)-B
AR60(K)-B
AR50P-410S
AR60P-410S
4
Diaphragm assembly
Weatherable NBR
AR20P-150AS
AR25P-150AS
AR30P-150AS
AR40P-150AS
AR50P-150AS
5
Valve guide assembly
Polyacetal
AR20P-050AS
AR25P-050AS
AR30P-050AS
AR40P-050AS
AR50P-050AS AR60P-050AS
6
Knob
Polyacetal
AR23P-030
AR28P-030
AR33P-030
AR43P-030
AR52P-030
7
Check valve assembly Note)
—
AR23KP-020AS
Note) Check valve assembly is applicable for a regulator with backflow function (AR20K-B to AR60K-B) only.
Assembly of a check valve cover, check valve body assembly and 2 mounting screws
70
AW
2
AR20(K)-B to
AR40(K)-B
AF
AR10-A
Polyacetal
AR10-A
Series AR20K-B to AR60K-B
Series
Working Principle (Regulator with Backflow Function)
AR10-A
@
@
IN
OUT
IN
OUT
(Inlet pressure)
(Outlet pressure)
(Inlet pressure)
(Outlet pressure)
:
:
Figure 1
Figure 2
When the inlet pressure is higher than the regulating pressure, the check valve operates as a normal regulator (Figure 1).
When the inlet pressure is shut off and exhausted, any inlet pressure applied to the valve q will be lost. The force for seating the valve q
is the valve spring force w only. When the valve q is opened using the outlet force, the outlet pressure will be exhausted at the inlet side
(Figure 2). When the set pressure is 0.15 MPa or less, the valve q may not open due to the valve spring w force.
AR20K-B to AR60K-B
A
A-A
1
OUT
@
2
IN
SMC
A
@
Inlet pressure
(IN)
@
Pressure in
diaphragm chamber
Inlet pressure
(IN)
Pressure in
diaphragm chamber
;
;
IN
OUT
(Inlet pressure)
(Outlet pressure)
IN
OUT
:
:
.
.
Figure 1 Normal
Figure 2 Backflow
When the inlet pressure is higher than the regulating pressure, the check valve w closes and operates as a normal regulator (Figure 1).
When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released
into the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator
spring e lifts the diaphragm. The valve r opens through the stem, and the outlet pressure is released to the inlet side (Figure 2).
71
72
AW
AL
AR
AFM / AFD
AF
Attachment
AW AFM
AF AFM AR
AF AR
AW AL
AF AR AL
AC
Series AR10-A
Series AR20-B to AR60-B
Series AR20K-B to AR60K-B
Dimensions
AR10-A
Panel fitting dimensions
2 x P1
(Port size)
P2
A
C
(Pressure gauge port size)
W
OUT
OUT
IN
B
R
Q
V
IN
F
Plate thickness
AR10-A: Max. 3.5
S
D
J
U
M
N
T
Bracket
(Option)
AR20(K)-B to AR40(K)-06-B
2 x P1
(Port size)
Panel fitting dimensions
A
K
C
W
Y
OUT
IN
IN
OUT
Plate thickness
AR20(K)-B to AR30(K)-B: Max. 3.5
AR40(K)-B
: Max. 5
R
B
Q
V
Z
F
P2
S
(Pressure gauge port size)
D
J
U
M
Bracket
(Option)
N
T
AR50(K)-B/AR60(K)-B
2 x P1
(Port size)
K
C
A
OUT
R
B
Q
IN
F
P2
S
(Pressure gauge port size)
D
J
73
U
M
Bracket
(Option)
N
T
AR10-A
Regulator Series AR20-B to AR60-B
Regulator with Backflow Function Series AR20K-B to AR60K-B
AC
J
Centre of
piping
Centre of
piping
AF AR AL
H
H
Centre of
piping
Dimensions
Round type pressure gauge Round type pressure gauge (with colour zone)
J
Optional specifications
Standard specifications
Model
P1
M5 x 0.8
AR10-A
1/8, 1/4
AR20(K)-B
1/4, 3/8
AR25(K)-B
1/4, 3/8
AR30(K)-B
1/4, 3/8, 1/2
AR40(K)-B
3/4
AR40(K)-06-B
3/4, 1
AR50(K)-B
1
AR60(K)-B
C
Square type
pressure gauge
Digital pressure
switch
Round type
Round type pressure gauge
pressure gauge
(with colour zone)
P2
A
B Note 1)
D
F
J
K
H
J
H
J
H
J
H
J
1/16
25
47.4
11
12.5
M18 x 1
12.5
—
—
—
—
—
ø26
26
—
—
1/8
40
67.4
26.5
28.5
M28 x 1
28.5
2 Note 2)
첸28
29.5
첸27.8
40
ø37.5
65
ø37.5
66
1/8
53
71.9
28
27.5
M32 x 1.5
27.5
0
첸28
28.5
첸27.8
39
ø37.5
64
ø37.5
65
1/8
53
85.6
30.7
29.4
M38 x 1.5
29.4
3.5
첸28
30.4
첸27.8
40.9
ø37.5
65.9
ø37.5
66.9
1/8
70
91.7
35.8
33.8
M42 x 1.5
33.8
3.5
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
1/8
75
93.2
35.8
33.8
M42 x 1.5
33.8
3
첸28
34.8
첸27.8
45.3
ø42.5
71.3
ø42.5
71.3
1/8
90
125.2
43
43.3
M62 x 1.5
43.3
3.2
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
1/8
95
129.6
46
43.3
M62 x 1.5
43.3
3.2
첸28
44.3
첸27.8
54.8
ø42.5
80.8
ø42.5
80.8
Optional specifications
M
N
25
28
30
30
Q
Panel mount
R
S
T
U
V
W
Y
Z
30
4.5
6.5
40
2
18
18.5
—
—
34
43.9
5.4
15.4
55
2.3
24.7
28.5
14
6
34
43.9
5.4
15.4
55
2.3
25.7
32.5
16
6
41
40
45.8
6.5
8
53
2.3
31.1
38.5
19
7
50
54
54
8.5
10.5
70
2.3
35.5
42.5
21
7
50
54
55.5
8.5
10.5
70
2.3
37
42.5
21
7
70
66
65.8
11
13
90
3.2
—
—
—
—
70
66
65.8
11
13
90
3.2
—
—
—
—
AW AFM
AR10-A
AR20(K)-B
AR25(K)-B
AR30(K)-B
AR40(K)-B
AR40(K)-06-B
AR50(K)-B
AR60(K)-B
Bracket mount
Attachment
Model
AW AL
Digital pressure switch
J
AF AR
Square embedded type pressure gauge
H
Option
Series
AF AFM AR
Regulator
AW
AL
AR
AFM / AFD
AF
Note 1) The dimension of B is the length when the filter regulator knob is unlocked.
Note 2) For the AR20 (K) -B only, the position of the pressure gauge is above the centre of the piping.
74
75
Modular Type
Lubricator
AL20-A
1/8, 1/4
AL30-A
1/4, 3/8
AL40-A
1/4, 3/8, 1/2
1
Attachment
AL60-A
AF
3/4, 1
AFM / AFD
AL50-A
AW AFM
3/4
AR
P.77 to 82
Bracket (Except AL10-A)
AL
AL40-06-A
AF AR AL
M5 x 0.8
AW AL
AL10-A
Option
AF AR
Port size
AF AFM AR
Model
AW
Lubricator
Series AL
AC
Series AL
76
Lubricator
AL10-A to AL60-A
Symbol
AL10-A
How to Order
AL 30
03 B
q
w
e
A
r
t
AL20-A
AL40-A
• Option/Semi-standard: Select one each for a to d.
• Option/Semi-standard symbol: When more than one specification is
required, indicate in alphanumeric order.
Example) AL30-03B-3RW-A
Nq
Symbol
Description
10
20
30
40
50
60
N
F
Metric thread (M5)
Rc
NPT
G
V
—
—
—
—
V
V
V
—
V
V
V
—
V
V
V
—
V
V
V
—
V
V
V
M5
01
02
03
04
06
10
M5 x 0.8
1/8
1/4
3/8
1/2
3/4
1
V
—
—
—
—
—
—
—
V
V
—
—
—
—
—
—
V
V
—
—
—
—
—
V
V
V
V
—
—
—
—
—
—
V
V
—
—
—
—
—
—
V
V
—
V
V
V
V
V
V
V
V
V
V
V
V
V
—
—
—
V
V
V
—
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
—
V
V
—
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
—
w
Pipe thread type
+
e
Port size
+
r
Option (Mounting)
—
Without mounting option
B Note 1) With bracket
+
t
Semi-standard
a
Bowl Note 2)
—
2
6
8
C
6C
+
b
Lubricant
exhaust port
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
With bowl guard (Nylon bowl)
Without drain cock
—
With drain cock
3
3W Note 5) Drain cock with barb fitting
+
c
Flow direction
—
R
Flow direction: Left to right
Flow direction: Right to left
—
Name plate and caution plate: MPa
+
d
Pressure unit
Z Note 6) Name plate and caution plate: psi, °F
Note 1) Option is not assembled and supplied loose at the time of shipment.
Note 2) Refer to Chemical data on page 80 for chemical resistance of the bowl.
Note 3) A bowl guard is provided as standard equipment (polycarbonate).
Note 4) A bowl guard is provided as standard equipment (nylon).
Note 5) The combination of metal bowl: 2 and 8 is not available.
Note 6) For pipe thread type: M5, NPT.
Note 7) v: For pipe thread type: M5, NPT only
77
Body size
— Note 3) — Note 3) — Note 3) — Note 3)
— Note 4) — Note 4) — Note 4) — Note 4)
V
V
V
V
V
V
v Note 7) v Note 7) v Note 7) v Note 7) v Note 7) v Note 7)
Lubricator
Series AL10-A
to AL60-A
1/4, 3/8
4
15
7
25
—
0.07
Semi-standard (Steel)
0.10
AL40-A
AL40-06-A
AL50-A
1/4, 3/8, 1/2
3/4
3/4, 1
Air
–5 to 60°C (with no freezing)
1.5 MPa
1.0 MPa
1/4:30
1/4:30
3/8:40
50
190
3/8:40
1/2:50
55
135
Class 1 turbine oil (ISO VG32)
Polycarbonate
Standard (Polycarbonate)
0.20
0.38
0.43
0.94
AL60-A
1
AF AR AL
AL30-A
1/8, 1/4
220
AW AL
Oil capacity [cm3]
Recommended lubricant
Bowl material
Bowl guard
Weight [kg]
AL20-A
M5 x 0.8
1.09
AF AFM AR
Note) · The flow rate is 5 drops or greater/min under the following conditions: Inlet pressure of 0.5 MPa; Class 1 turbine oil (ISO VG32); Temperature at 20°C; Oil
adjustment valve fully open.
· For a circuit that repeatedly turns ON and OFF on the outlet side, make the adjustment so that the average air consumption per minute becomes the minimum
dripping flow rate or more.
Options/Part No.
Optional specifications
Bracket assembly Note)
Model
AL10-A
—
AL20-A
AL30-A
AL40-A
AL40-06-A
AL50-A
AF22P-050AS AF32P-050AS AF42P-050AS AF42P-070AS
AL60-A
AF52P-050AS
Note) Assembly of a bracket and 2 mounting screws
Bowl Assembly/Part No.
Model
AL10-A
AL20-A
AL30-A
—
C1SL-A
C2SL-A
—
With bowl guard
—
C2SL-C-A
C3SL-A
Polycarbonate
—
C1SL-3-A
C2SL-3-A
—
bowl
With drain cock
With bowl guard
—
C2SL-3C-A C3SL-3-A
Drain cock with barb fitting With bowl guard
—
—
C3SL-3W-A
—
C1SL-6-A
C2SL-6-A
—
Without drain cock
With bowl guard
—
C2SL-6C-A C3SL-6-A
Nylon bowl
—
C1SL-36-A C2SL-36-A
—
With drain cock
With bowl guard
—
C2SL-36C-A C3SL-36-A
Drain cock with barb fitting With bowl guard
—
—
C3SL-36W-A
—
C1SL-2-A
C2SL-2-A
C3SL-2-A
Without drain cock
With level gauge
—
—
C3LL-8-A
Metal bowl
—
C1SL-23-A C2SL-23-A C3SL-23-A
With drain cock
With level gauge
—
—
C3LL-38-A
Without drain cock
AL40-A
AL40-06-A
AL50-A
AL60-A
Attachment
Other
—
C4SL-A
—
C4SL-3-A
C4SL-3W-A
—
C4SL-6-A
—
C4SL-36-A
C4SL-36W-A
C4SL-2-A
C4LL-8-A
C4SL-23-A
C4LL-38-A
AF
Lubricant
exhaust port
AFM / AFD
Bowl
material
AF AR
Minimum dripping flow rate
[L/min (ANR)] Note)
AL10-A
AW AFM
Model
Port size
Fluid
Ambient and fluid temperature
Proof pressure
Maximum operating pressure
AC
Standard Specifications
AW
AL
AR
Note) · Bowl seal is included for the AL20-A to AL60-A.
· Please consult with SMC separately for psi and °F unit display specifications.
78
Series AL10-A
to AL60-A
Flow-rate Characteristics (Representative values)
AL10-A
150
0.02
1000
2000
3000
6000
AL60-A
Pa
P1
=0
.
P1 5 M
Pa
=0
.7
M
Pa
=0
.3
M
6000
P1
Rc1
.3
MP
P1
a
=0
.5
M
P1 Pa
=0
.7
M
Pa
P1
=0
0.08
MP
a
0.06
P1
=0
.1
0.04
0.02
0
2000
4000
6000
Flow rate L/min (ANR)
Flow rate L/min (ANR)
Pressure drop [MPa]
MP
a
P1
=0
.7
MP
a
0.02
0
8000
P1=
0.5
MPa
0.04
0
4000
P1=
0.3
MPa
0.06
P1=0.1
Pressure drop [MPa]
Pa
M
.7
P1
=0
P1=
0
2000
Pa
AL50-A
0.1
0.08
4000
Flow rate L/min (ANR)
Rc3/4
a
MP
a
0.5
MP
0.3
P1 =
Pa
.1 M
P1=0
0.02
0
2000
0
0.1
0.1
0.04
0.02
4000
AL40-06-A
Rc1/2
0.06
0.04
Flow rate L/min (ANR)
AL40-A
0.08
0.06
0
0
200
0.08
P1 =
0.1
M
.5
MP
a
P1
=0
.7
M
Pressure drop [MPa]
0.04
Flow rate L/min (ANR)
Pressure drop [MPa]
P1
=0
0.06
0
0
100
Rc3/8
Pa
Conditions: P1 = 0.5 MPa
Needle: One side fully open
0.08
MP
a
P1
=0
.3
MP
a
Ope
0.02
50
AL30-A
0.1
P1=
0.1
n 1.
n 2.0
5 tu
turns
rns
rn
Ope
0.04
0
Rc1/4
0.1
Pressure drop [MPa]
0.06
1.0 tu
0.08
Open
open
Open 0
.5 turn
Needle fully
Pressure drop [MPa]
0.1
AL20-A
M5
8000
0
5000
10000
15000
Flow rate L/min (ANR)
Rc1
Pa
Pa
M
Pa
P1
=0
.5
M
P1
=0
.3
0.08
M
P1
Pa
0.06
7
.
=0
.1
M
0.04
P1
=0
Pressure drop [MPa]
0.1
0.02
0
0
5000
10000
15000
Flow rate L/min (ANR)
Working Principle: AL10 Type
Needle
79
Section AA’
A portion of the air introduced from the IN side pressurizes the lubricant inside the bowl. The remainder
of the air passes through the needle o, and flows to the OUT side. The differential pressure between the
inside of the bowl and the inside of the sight dome w, causes the lubricant inside the bowl into the oil
passage !0. The lubricant drips from the dripping tube !1, and lubricates the OUT side. The amount of
lubricant is adjusted by the needle o on the front face. Turning the needle clockwise increases the
amount of the lubricant, and turning it counterclockwise until fully open shuts off the lubricant. The needle
on the side that is not used should be left fully open.
Series AL10-A
to AL60-A
Caution
Effects of atmosphere of organic solvents and chemicals, and
where these elements are likely to adhere to the equipment.
Chemical data for substances causing degradation (Reference)
Acid
Alkaline
Inorganic
salts
Chlorine
solvents
Aromatic
series
Ketone
Alcohol
Oil
Chemical name
Hydrochloric acid
Sulfuric acid, Phosphoric acid
Chromic acid
Sodium hydroxide (Caustic soda)
Potash
Calcium hydroxide (Slack lime)
Ammonia water
Carbonate of soda
Sodium sulfide
Sulfate of potash
Sulfate of soda
Carbon tetrachloride
Chloroform
Ethylene chloride
Methylene chloride
Benzene
Toluene
Paint thinner
Acetone
Methyl ethyl ketone
Cyclohexane
Ethyl alcohol
IPA
Methyl alcohol
Gasoline
Kerosene
Application examples
Material
Polycarbonate Nylon
Acid washing liquid
for metals
왕
҂
Degreasing of metals
Industrial salts
Water-soluble cutting oil
҂
쑗
Caution
—
҂
왕
Cleansing liquid for metals
Printing ink
Dilution
҂
왕
1. Check the dripping amount once a day. Drip failure can cause
damage to the components that need lubrication.
Mounting/Adjustment
Coatings
Dry cleaning
҂
왕
Photographic film
Dry cleaning
Textile industries
҂
҂
Antifreeze
Adhesives
왕
҂
—
Warning
1. For the AL10-A/AL20-A type, replenish the lubricant after releasing the inlet pressure. Lubrication cannot take place under
a pressurized condition.
2. Adjustment of the oil regulating valve for models from the
AL20-A to AL60-A should be carried out manually. Turning it
counterclockwise increases the dripping amount, and turning it
clockwise reduces the dripping amount. The use of tools etc.
can result in damage to the unit. From the fully closed position, three rotations will bring it to the fully open position.
Do not rotate it any further than this. Note that the numbered
scale markings are guidelines for adjusting the position, and
not indicators of the dripping amount.
Caution
1. When the bowl is installed on the AL30-A to AL60-A, install
them so that the lock button lines up to the groove of the front
(or the back) of the body to avoid drop or damage of the bowl.
AFM / AFD
Type
Maintenance
Lock button
҂
AW AL
1. Use a check valve (Series AKM) to prevent back flow of the lubricant when redirecting the air flow before the lubricator.
Warning
AF AR
1. Do not introduce air from the outlet side as this can damage the
bumper.
2. The standard bowl for the air filter, filter regulator, and lubricator, as well as the sight dome for the lubricator are
made of polycarbonate. Do not use in an environment
where they are exposed to or come in contact with organic
solvents, chemicals, cutting oil, synthetic oil, alkali, and
thread lock solutions.
AF AFM AR
Selection
AW AFM
Selection
Attachment
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
AF AR AL
AC
Specific Product Precautions
AF
Lubricator
쑗
AR
Phthalic acid dimethyl
Synthetic oil
Phthalic acid diethyl
҂
쑗
Anti-rust additives
Acetic acid
Methyl ether
Brake oil additives
Ether
҂
쑗
Ethyl ether
Cutting oil
Amino
Methyl amino
Brake oil additives
҂
҂
Rubber accelerator
Thread-lock fluid
Others
Seawater
—
҂
왕
Leak tester
쑗: Essentially safe 왕: Some effects may occur. ҂: Effects will occur.
AW
AL
Ester
When the above factors are present, or there is some doubt, use a metal bowl
for safety.
80
Series AL10-A
to AL60-A
Construction
AL10-A
AL20-A
@
:
=
@
:
OUT
IN
IN
OUT
B
;
>
B
>
AL30-A /AL40-A
@
:
=
AL50-A /AL60-A
@ .
:
=
.
OUT
IN
OUT
IN
.
;
B
>
;
2
B
>
Component Parts
No.
Description
1
Body
8
Housing
Material
Model
Zinc die-cast
AL10-A
Colour
Aluminium die-cast
AL20-A to AL60-A
Aluminium die-cast
AL50-A /AL60-A
White
White
Replacement Parts
Part no.
No.
Description
Material
2
Sight dome assembly
Polycarbonate
AL10P-080AS
3
Lubrication plug assembly
—
—
AL22P-060AS
AL32P-060AS
4
Bumper retainer assembly
—
—
AL20P-030AS
AL30P-030AS
AL40P-030AS
AL50P-030AS
AL60P-030AS
5
Bumper (assembly)
Synthetic resin
—
AL20P-040S
AL30P-040S
AL40P-040S
AL50P-040AS
AL60P-040AS
6
Bowl seal
NBR
C1SFP-260S
C2SFP-260S
C32FP-260S
C42FP-260S
7
Bowl assembly Note)
Polycarbonate
C1SL-A
C2SL-A
C3SL-A
C4SL-A
AL10-A
AL20-A
AL30-A
AL40-A
AL40-06-A
AL60-A
AL42P-060AS
Note) · Bowl seal is included for the AL20-A to AL60-A. Please consult with SMC separately for psi and °F unit display specifications.
· Bowl assembly for the AL30-A to AL60-A models comes with a bowl guard (Material: Polycarbonate).
81
AL50-A
AL20P-080AS
Lubricator
Series AL10-A
to AL60-A
T
N
B
A
AL10-A /AL20-A
Metal bowl
AF
Metal bowl with drain cock
B
B
Dimensions
AL30-A to AL60-A
Metal bowl
B
With drain cock
B
Applicable model
G
2xP
(Port size)
Clearance for
maintenance
A
G
Clearance for
maintenance
E
AL30-A to AL60-A
Metal bowl with level gauge, with drain cock
B
B
Dimensions
Metal bowl with drain cock
Drain cock with barb fitting
B
Metal bowl with level gauge
B
With drain cock
B
Applicable model
Optional/Semi-standard specifications
Barb fitting
applicable
tubing: T0604
Optional specifications
Standard specifications
Model
P
M5 x 0.8
AL10-A
1/8, 1/4
AL20-A
1/4, 3/8
AL30-A
1/4, 3/8, 1/2
AL40-A
3/4
AL40-06-A
3/4, 1
AL50-A
1
AL60-A
AF AR AL
OUT
B
Bracket
(Option)
2xP
(Port size)
Optional/Semi-standard specifications
AF AR
C
C
IN
OUT
A
B
C
25
40
53
70
75
90
95
51.5
79.3
104.1
136.1
138.1
209.1
223.1
25.5
35.9
38.1
39.8
37.8
41.2
44.7
D
Semi-standard specifications
With
drain
cock
Bracket mount
E
12.5 —
—
20
26.7 30
35.5 38.4
35.5 38.4
—
45
47.5 —
G
J
35
60
80
110
110
110
110
12.5
20
26.7
35.5
35.5
45
47.5
M N Q
—
30
41
50
50
70
70
—
27
40
54
54
66
66
R
— —
22 5.4
23 6.5
26 8.5
25 8.5
35 11
35 11
With
barb
fitting
AF AFM AR
R
R
S
S
IN
AW AL
B
U
D
Q
V
T
N
M
Metal
bowl
Metal bowl Metal bowl Metal bowl with
with
with level level gauge,
drain cock gauge with drain cock
S
T
U
V
B
B
B
B
B
B
—
8.4
8
10.5
10.5
13
13
—
40
53
70
70
90
90
—
2.3
2.3
2.3
2.3
3.2
3.2
—
28
30
35
34
47
47
59.9
87.7
115.1
147.1
149.1
220.1
234.1
—
—
123.6
155.6
157.6
228.6
242.6
56.3
84.5
104.1
136.1
138.1
209.1
223.1
59.3
87.5
117.6
149.6
151.6
222.6
236.6
—
—
124.1
156.1
158.1
229.1
243.1
—
—
137.6
169.6
171.6
246.2
256.6
82
AFM / AFD
J
Q
V
U
Bracket
(Option)
AR
Q
V
AL50-A
AL60-A
T
N
M
OUT
A
AL30-A to AL40-06-A
J
C
C
2xP
(Port size)
IN
AL
Clearance for
maintenance
2xP
(Port size)
B
OUT
S
G
IN
Bracket
(Option)
D
A
Clearance for
maintenance
JD
AW AFM
U
Attachment
M
AW
J
R
AL20-A
G
AL10-A
AC
Dimensions
83
Modular Type
Filter Regulator
AC
AF + AR + AL
Options
Bracket
AW10-A
M5 x 0.8
0.05 to 0.7 MPa
0.02 to 0.2 MPa
Round type pressure gauge
Set nut (for panel mount) ∗
Bracket
1/8, 1/4
Set nut (for panel mount) ∗
AF + AFM + AR
AW20-B
Float type auto drain
AW30-B
1/4, 3/8
Square embedded type
pressure gauge
Digital pressure switch
AW40-B
AW40-06-B
1/4, 3/8, 1/2
3/4
0.05 to 0.85 MPa
0.02 to 0.2 MPa
Round type pressure gauge
Bracket
Square embedded type
pressure gauge
Digital pressure switch
AW60-B
3/4, 1
AW + AL
Set pressure
AF + AR
Port size
Round type pressure gauge
P.85 to 96
AW
AL
AR
AFM / AFD
* Interchangeable with existing AW series
AW + AFM
Model
Attachment
Filter Regulator
Series AW
AW
AF
Series
84
Filter Regulator
AW10-A
Symbol
Filter Regulator
1
• Integrated filter and regulator units save space and require less piping.
2
L
How to Order
A
AW10 M5
q
w
• Option/Semi-standard: Select one each for a to h.
• Option/Semi-standard symbol: When more than one specification is required,
indicate in alphanumeric order.
Example) AW10-M5CG-12NR-A
Symbol
q
V
Option Note 1)
a
Mounting
b
Float type auto drain
Description
—
B
H
Without mounting option
With bracket
With set nut (for panel mount)
—
Without auto drain
+
Refer to page 87 for size 20 to 60.
C Note 2) N.C. (Normally closed) Drain port is closed when pressure is not applied.
+
c
Pressure gauge
—
Without pressure gauge
G Note 3) Round type pressure gauge (without limit indicator)
+
d
—
1
0.05 to 0.7 MPa setting
0.02 to 0.2 MPa setting
Bowl Note 5)
—
2
6
Polycarbonate bowl
Metal bowl
Nylon bowl
Exhaust mechanism
—
N
Relieving type
Non-relieving type
Flow direction
—
R
Flow direction: Left to right
Flow direction: Right to left
Pressure unit
—
Z
Name plate, caution plate, and pressure gauge in imperial units: MPa
Name plate, caution plate, and pressure gauge in imperial units: psi, °F
Set pressure
Note 4)
+
w
V
Semi-standard
e
+
f
+
g
+
h
Note 1) Option B, G, H are not assembled and supplied loose at the time of shipment.
Note 2) When pressure is not applied, condensate which does not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending operations for the day is recommended.
Note 3) A 1.0 MPa pressure gauge will be fitted. It is not assembled and supplied loose at the time of shipment.
Note 4) Pressure can be set higher than the specification pressure in some cases, but use pressure within the specification range.
Note 5) Refer to Chemical data on page 90 for chemical resistance of the bowl.
85
Series AW10-A
AF + AR + AL
AC
Filter Regulator
AW + AL
AW10-A
Standard Specifications
Port size
M5 x 0.8
Pressure gauge port size
Fluid
AF + AR
1/16
Air
–5 to 60°C (with no freezing)
Proof pressure
1.5 MPa
Maximum operating pressure
1.0 MPa
Set pressure range
AF + AFM + AR
Ambient and fluid temperature
0.05 to 0.7 MPa
Nominal filtration rating
5 mm
Drain capacity [cm ]
Bowl material
Polycarbonate
Construction
Relieving type
Weight [kg]
AW + AFM
2.5
3
0.09
Bracket assembly Note 1)
Attachment
Options/Part No.
AR12P-270AS
Set nut
AR12P-260S
Round type pressure gauge Note 2)
G27-10-R1
AF
Note 1) Assembly of a bracket and set nuts
Note 2) 1.0 MPa pressure gauge
Polycarbonate bowl
Nylon bowl
Metal bowl
Drain discharge mechanism
Drain port
Bowl part no.
Manual discharge
Automatic discharge (Auto drain) Note 2)
Manual discharge
Automatic discharge (Auto drain) Note 2)
Manual discharge
Automatic discharge (Auto drain) Note 2)
With drain cock
Normally closed (N.C.)
With drain cock
Normally closed (N.C.)
With drain cock
Normally closed (N.C.)
C1SF-A
AD17-A
C1SF-6-A
AD27-6-A
C1SF-2-A
AD17-2-A
AR
Bowl material
AFM / AFD
Bowl Assembly/Part No.
AW
AL
Note 1) Please consult with SMC separately for psi and °F unit display specifications.
Note 2) Minimum operating pressure: 0.1 MPa
86
Filter Regulator
AW20-B to AW60-B
Filter Regulator with Backflow Function
AW20K-B to AW60K-B
Symbol
Filter Regulator with
Backflow Function
Filter Regulator
1
2
1
2
L
L
• Integrated filter and regulator units save space and require less piping.
• With the backflow function it incorporates a mechanism to exhaust the air pressure in
the outlet side reliably and quickly.
Example)
When the air supply is cut off and releasing the inlet pressure to the atmosphere, the residual
pressure release of the outlet side can be ensured for a safety purpose.
12
1
q
w
B
03 BE
e
Symbol
r
t
y
With backflow
function
—
K Note 1)
+
q
V
Description
Body size
Pipe thread type
N Note 2)
F Note 3)
Rc
NPT
G
01
02
03
04
06
10
1/8
1/4
3/8
1/2
3/4
1
+
r
V
Port size
+
a
Mounting
30
40
60
—
—
—
—
—
—
—
—
—
—
Without backflow function
With backflow function
—
e
V
L
10
• Option/Semi-standard: Select one each for a to i.
• Option/Semi-standard symbol: When more than one specification is
required, indicate in alphanumeric order.
Example) AW30K-03BE-1N-B
20
w
V
2
3
Refer to page 85 for size 10.
How to Order
AW 30 K
2 1
2 1
L
—
—
—
—
Without mounting option
—
B Note 5) With bracket
With set nut (for panel mount)
H
—
+
t
V
Option Note 4)
b
Float type
auto drain
Without auto drain
—
C Note 6) N.C. (Normally closed) Drain port is closed when pressure is not applied.
D Note 7) N.O. (Normally open) Drain port is open when pressure is not applied.
+
—
E
G
M
E1
E2
E3
E4
Without pressure gauge
Square embedded type pressure gauge (with limit indicator)
Round type pressure gauge (with limit indicator)
Round type pressure gauge (with colour zone)
Output: NPN output / Electrical entry: Wiring bottom entry
Output: NPN output / Electrical entry: Wiring top entry
Output: PNP output / Electrical entry: Wiring bottom entry
Output: PNP output / Electrical entry: Wiring top entry
Set
d
pressure Note 10)
—
1
0.05 to 0.85 MPa setting
0.02 to 0.2 MPa setting
e
—
2
6
8
C
6C
Polycarbonate bowl
Metal bowl
Nylon bowl
Metal bowl with level gauge
With bowl guard
Nylon bowl with bowl guard
—
With drain cock
Drain guide 1/8
Drain guide 1/4
Drain cock with barb fitting
Pressure
gauge Note 8)
c
Digital
pressure
switch Note 9)
y
V
Semi-standard
+
Bowl Note 11)
+
+
f Drain port Note 14) J Note 15)
W Note 16)
87
—
—
—
—
— Note 12)
— Note 13)
— Note 12)
— Note 13)
— Note 12)
— Note 13)
—
—
—
to AW60-B
Series AW20K-B to AW60K-B
Filter Regulator
AW40-B, AW40K-B
AF AR
AW20-B, AW20K-B
q
앬
Flow direction
—
R
30
40
60
Note 19)
Note 19)
Note 19)
Note 19)
Note 20)
Note 20)
Note 20)
Note 20)
AF AFM AR
—
N
20
Relieving type
Non-relieving type
+
h
Flow direction: Left to right
Flow direction: Right to left
+
i
Pressure unit
Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa
Z Note 17) Name plate, caution plate for bowl, and pressure gauge in imperial units: psi, °F
ZA Note 18) Digital pressure switch: With unit conversion function
Note 1) Set the inlet pressure to at least 0.05 MPa higher than
the set pressure.
Note 2) Drain guide is NPT1/8 (applicable to the AW20(K)-B) and
NPT1/4 (applicable to the AW30(K)-B to AW60(K)-B).
The auto drain port comes with ø3/8" One-touch fitting
(applicable to the AW30(K)-B to AW60(K)-B).
Note 3) Drain guide is G1/8 (applicable to the AW20(K)-B) and
G1/4 (applicable to the AW30(K)-B to AW60(K)-B).
Note 4) Option B, G, H, M are not assembled and supplied loose
at the time of shipment.
Note 5) Assembly of a bracket and set nuts (applicable to the
AW20(K)-B to AW40(K)-B). Including 2 mounting screws
for the AW60(K)-B
Note 6) When pressure is not applied, condensate which does
not start the auto drain mechanism will be left in the bowl.
Releasing the residual condensate before ending
operations for the day is recommended.
Note 7) If the compressor is small (0.75 kW, discharge flow is
less than 100 L/min[ANR]), air leakage from the drain
cock may occur during start of operations. N.C. type is
recommended.
Note 8) When the pressure gauge is attached, a 1.0 MPa
pressure gauge will be fitted for standard (0.85 MPa)
type. 0.4 MPa pressure gauge for 0.2 MPa type.
Note 9) When choosing with H (panel mount), the installation
space for lead wires will not be secured. In this case,
select “wiring top entry” for the electrical entry. (Select
“wiring bottom entry” when the semi-standard Y is chosen
simultaneously.)
Note 10) Pressure can be set higher than the specification
pressure in some cases, but use pressure within the
specification range.
Note 11) Refer to Chemical data on page 90 for chemical
resistance of the bowl.
Note 12) A bowl guard is provided as standard equipment
(polycarbonate).
Note 13) A bowl guard is provided as standard equipment (nylon).
Note 14) The combination of float type auto drain: C and D is not
available.
Note 15) Without a valve function
Note 16) The combination of metal bowl: 2 and 8 is not available.
Note 17) For pipe thread type: NPT. Cannot be used with M:
Round pressure gauge (with colour zone). Available by
request for special. The digital pressure switch will be
equipped with the unit conversion function, setting to psi
initially.
Note 18) For options: E1, E2, E3, E4.
Note 19) 쑗: For pipe thread type: NPT only
Note 20) 왕: Select with options: E1, E2, E3, E4.
AF
—
Standard Specifications
AW40-B
1/4, 3/8
1/4, 3/8, 1/2
1/8
Air
–5 to 60°C (with no freezing)
1.5 MPa
1.0 MPa
0.05 to 0.85 MPa
5 μm
8
25
Semi-standard (Steel)
0.20
0.36
AW40-06-B
3/4
45
Polycarbonate
Standard (Polycarbonate)
Relieving type
0.66
0.72
AW60-B
3/4, 1
AR
AW30-B
1/8, 1/4
AL
AW20-B
AW
Model
Port size
Pressure gauge port size Note 1)
Fluid
Ambient and fluid temperature Note 2)
Proof pressure
Maximum operating pressure
Set pressure range
Nominal filtration rating
Drain capacity [cm3]
Bowl material
Bowl guard
Construction
Weight [kg]
AW AFM
Exhaust
mechanism
Body size
AFM / AFD
y
앬
Semi-standard
g
Description
Attachment
Symbol
AW AL
AF AR AL
AC
Filter Regulator with Backflow Function
Series AW20-B
2.05
Note 1) Pressure gauge connection threads are not available for F.R.L. unit with a square embedded type pressure gauge or with a digital pressure switch.
Note 2) –5 to 50°C for the products with the digital pressure switch
88
Series AW20-B
to AW60-B
Series AW20K-B to AW60K-B
Options/Part No.
Optional specifications
Bracket assembly Note 1)
Set nut
Standard
0.02 to 0.2 MPa setting
Standard
Pressure Round type Note 3)
(with colour zone) 0.02 to 0.2 MPa setting
gauge
Standard
Square embedded
type Note 4)
0.02 to 0.2 MPa setting
NPN output: Wiring bottom entry
NPN output: Wiring top entry
Digital pressure
switch Note 5)
PNP output: Wiring bottom entry
PNP output: Wiring top entry
Round type Note 3)
Model
AW20(K)-B
AW30(K)-B
AW40(K)-B
AW40(K)-06-B
AW23P-270AS
AR33P-270AS
AR43P-270AS
AR23P-260S
AR33P-260S
AR43P-260S
G36-10-첸01
G46-10-첸01
G36-4-첸01
G46-4-첸01
G36-10-첸01-L
G46-10-첸01-L
G36-4-첸01-L
G46-4-첸01-L
GC3-10AS [GC3P-010AS (Pressure gauge cover only)]
GC3-4AS [GC3P-010AS (Pressure gauge cover only)]
ISE35-N-25-MLA [ISE35-N-25-M (Switch body only)]
ISE35-R-25-MLA [ISE35-R-25-M (Switch body only)]
ISE35-N-65-MLA [ISE35-N-65-M (Switch body only)]
ISE35-R-65-MLA [ISE35-R-65-M (Switch body only)]
AW60(K)-B
AW62P-270AS
— Note 2)
Note 1) Assembly of a bracket and set nuts. Including 2 mounting screws for the AW60(K)-B
Note 2) Please consult with SMC regarding the set nuts for the AW60(K)-B.
Note 3) 첸 in part numbers for a round pressure gauge indicates a pipe thread type.
No indication is necessary for R; however, indicate N for NPT.
Please contact SMC regarding the pressure gauge supply for psi unit specifications.
Note 4) Including one O-ring and 2 mounting screws.
[ ]: Pressure gauge cover only
Note 5) In addition to the pressure switch body, lead wire with connector (2 m), adapter, lock pin, O-ring (1 pc.), mounting screw (2 pcs.) are attached.
[ ]: Switch body only. (Regarding how to order the digital pressure switch, please consult with SMC.
A pressure switch can be mounted on the AW60(K)-B, with a special mounting adapter (Pressure switch adapter assembly: AW63P-310AS) and mounting
screws (M3 x 0.5 x 14) which are delivered with the mounting adapter.
Bowl Assembly/Part No.
Bowl
material
Drain
discharge
mechanism
Model
Drain port
With drain cock
Manual
discharge
Drain cock with barb fitting
With drain guide
(without valve function)
Polycarbonate
bowl
Automatic
discharge Note)
(Auto drain)
Normally closed (N.C.)
Normally open (N.O.)
With drain cock
Manual
discharge
Drain cock with barb fitting
With drain guide
(without valve function)
Nylon bowl
Automatic
discharge Note)
(Auto drain)
Manual
discharge
Metal bowl
Automatic
discharge Note)
(Auto drain)
Normally closed (N.C.)
Normally open (N.O.)
With drain cock
With drain guide
(without valve function)
Normally closed (N.C.)
Normally open (N.O.)
Other
—
With bowl guard
With bowl guard
—
With bowl guard
—
With bowl guard
With bowl guard
—
With bowl guard
With bowl guard
—
With bowl guard
—
With bowl guard
With bowl guard
—
With level gauge
—
With level gauge
—
With level gauge
—
With level gauge
AW20-B
AW30-B
C2SF-A
C2SF-C-A
—
C2SF첸-J-A
C2SF첸-CJ-A
AD27-A
AD27-C-A
—
C2SF-6-A
C2SF-6C-A
—
C2SF첸-6J-A
C2SF첸-6CJ-A
AD27-6-A
AD27-6C-A
—
C2SF-2-A
—
C2SF첸-2J-A
—
AD27-2-A
—
—
—
—
C3SF-A
C3SF-W-A
—
C3SF첸-J-A
—
AD37첸-A
AD38첸-A
—
C3SF-6-A
C3SF-6W-A
—
C3SF첸-6J-A
—
AD37첸-6-A
AD38첸-6-A
C3SF-2-A
C3LF-8-A
C3SF첸-2J-A
C3LF첸-8J-A
AD37첸-2-A
AD37첸-8-A
AD38첸-2-A
AD38첸-8-A
AW40-B
AW40-06-B
—
C4SF-A
C4SF-W-A
—
C4SF첸-J-A
—
AD47첸-A
AD48첸-A
—
C4SF-6-A
C4SF-6W-A
—
C4SF첸-6J-A
—
AD47첸-6-A
AD48첸-6-A
C4SF-2-A
C4LF-8-A
C4SF첸-2J-A
C4LF첸-8J-A
AD47첸-2-A
AD47첸-8-A
AD48첸-2-A
AD48첸-8-A
Note) Minimum operating pressure: N.O. type–0.1 MPa (AD38-A, AD48-A); N.C. type–0.1 MPa (AD27-A) and 0.15 MPa (AD37-A, AD47-A).
Bowl assembly comes with a bowl seal.
첸 in bowl assembly part numbers indicates a pipe thread type (applicable tubing for auto drain).
No indication is necessary for Rc thread; however, indicate N for NPT thread, and F for G thread. (For auto drain, —: ø10, N: ø3/8")
Please consult with SMC separately for psi and °F unit display specifications.
89
AW60-B
to AW60-B
Maintenance
Warning
Warning
1. Residual pressure disposal (outlet pressure removal) is not possible for the AW20-B to AW60-B even though the inlet pressure is
exhausted. When the residual pressure disposal is performed, use
the filter regulator with backflow function (AW20K-B to AW60K-B).
1. Replace the element every 2 years or when the pressure drop
becomes 0.1 MPa, whichever comes first, to prevent damage
to the element.
2. The standard bowl for the air filter, filter regulator, and lubricator, as well as the sight dome for the lubricator are made of
polycarbonate. Do not use in an environment where they are
exposed to or come in contact with organic solvents, chemicals, cutting oil, synthetic oil, alkali, and thread lock solutions.
Mounting/Adjustment
Effects of atmosphere of organic solvents and chemicals, and
where these elements are likely to adhere to the equipment.
Chemical data for substances causing degradation (Reference)
Warning
1. Set the regulator while verifying the displayed values of the inlet and outlet pressure gauges. Turning the regulator knob excessively can cause damage to the internal parts.
2. Do not use tools on the pressure regulator knob as this may
cause damage. It must be operated manually.
Material
Chlorine
solvents
Aromatic
series
Ketone
Alcohol
Oil
Gasoline
Kerosene
왕
Degreasing of metals
Industrial salts
Water-soluble cutting oil
҂
쑗
—
҂
왕
Cleansing liquid for metals
Printing ink
Dilution
҂
왕
Coatings
Dry cleaning
҂
왕
Photographic film
Dry cleaning
Textile industries
҂
҂
Antifreeze
Adhesives
왕
҂
҂
쑗
—
҂
Phthalic acid dimethyl
Synthetic oil
Phthalic acid diethyl
҂
쑗
Anti-rust additives
Acetic acid
Methyl ether
Ether
Brake oil additives
҂
쑗
Ethyl ether
Cutting oil
Amino
Methyl amino
Brake oil additives
҂
҂
Rubber accelerator
Thread-lock fluid
Others
Seawater
—
҂
왕
Leak tester
쑗: Essentially safe 왕: Some effects may occur. ҂: Effects will occur.
When the above factors are present, or there is some doubt, use a metal bowl
for safety.
Ester
AW AFM
Acid washing liquid
for metals
Caution
1. Be sure to unlock the knob before adjusting the pressure and lock it after
setting the pressure. Failure to follow
this procedure can cause damage to
the knob and the outlet pressure may
fluctuate.
• Pull the pressure regulator knob to
unlock. (You can visually verify this
with the “orange mark” that appears
in the gap.)
• Push the pressure regulator knob to
lock. When the knob is not easily
locked, turn it left and right a little
and then push it (when the knob is
locked, the “orange mark”, i.e., the
gap will disappear).
2. A knob cover is available to prevent
careless operation of the knob. Refer
to page 97 for details.
3. When the bowl is installed on the
AW30-B to AW60-B, install them so
that the lock button lines up to the
groove of the front (or the back) of the
body to avoid drop or damage of the
bowl.
Orange
mark
Attachment
Nylon
AF
Inorganic
salts
Polycarbonate
Lock
button
AR
Alkaline
Hydrochloric acid
Sulfuric acid, Phosphoric acid
Chromic acid
Sodium hydroxide (Caustic soda)
Potash
Calcium hydroxide (Slack lime)
Ammonia water
Carbonate of soda
Sodium sulfide
Sulfate of potash
Sulfate of soda
Carbon tetrachloride
Chloroform
Ethylene chloride
Methylene chloride
Benzene
Toluene
Paint thinner
Acetone
Methyl ethyl ketone
Cyclohexane
Ethyl alcohol
IPA
Methyl alcohol
Application examples
AL
Acid
Chemical name
AW
Type
AW AL
Design/Selection
AF AR
Be sure to read this before handling. Refer to the back cover for Safety Instructions, “Handling Precautions for
SMC Products” and the Operation Manual for F.R.L. Precautions, http://www.smc.eu
AF AR AL
AC
Specific Product Precautions
AF AFM AR
Series AW20-B
AFM / AFD
Filter Regulator
90
AW10-A
AW20-B to AW60-B
AW20K-B to AW60K-B
Series
Series
Series
Flow-rate Characteristics (Representative values)
M5
AW20(K)-B
AW30(K)-B
0.6
0.5
0.5
0.5
0.4
0.3
0.2
0
Outlet pressure [MPa]
0.6
0.4
0.3
0.2
0.1
0.1
0
25
50
75
100
125
0
150
0
200
400
600
0.5
Outlet pressure [MPa]
0.5
0.4
0.3
0.2
Rc3/4
0
500
2000
0.3
0.2
Rc1
0.5
0.4
0.3
0.2
0.1
0
1000
2000
3000
0
0
4000
5000
Flow rate L/min (ANR)
Flow rate L/min (ANR)
Pressure Characteristics (Representative values)
AW10-A
1500
0.6
0.4
0
3000
1000
AW60(K)-B
0.1
0.1
1000
0.2
Flow rate L/min (ANR)
AW40(K)-06-B
0.6
0
0.3
0
800
Outlet pressure [MPa]
Rc1/2
0.6
0
0.4
Flow rate L/min (ANR)
AW40(K)-B
Rc3/8
0.1
Flow rate L/min (ANR)
Outlet pressure [MPa]
Rc1/4
0.6
Outlet pressure [MPa]
Outlet pressure [MPa]
AW10-A
Condition: Inlet pressure 0.7 MPa
10000
Flow rate L/min (ANR)
Conditions: Inlet pressure 0.7 MPa, Outlet pressure 0.2 MPa, Flow rate 20 L/min (ANR)
AW20(K)-B
AW30(K)-B
0.3
Set point
0.2
0.15
0
0
0.25
Set point
0.2
0.15
0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
0
0.2
0.3
0.6
0.7
0.8
0.9
0
1
0.2
0.5
0.6
0.7
0.8
0.3
0.9
1
0.4
0.5
0.6
0.7
0.8
0.9
1
0.25
Set point
0.2
0
0.4
Inlet pressure [MPa]
0.2
AW60(K)-B
Set point
0.2
0.15
0.15
0.3
0
Inlet pressure [MPa]
Outlet pressure [MPa]
Set point
Outlet pressure [MPa]
Outlet pressure [MPa]
0.5
0.25
0.15
91
0.4
AW40(K)-06-B
0.25
0.2
0.2
Inlet pressure [MPa]
AW40(K)-B
0
Set point
0.15
Inlet pressure [MPa]
0
Outlet pressure [MPa]
0.25
Outlet pressure [MPa]
Outlet pressure [MPa]
0.25
0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
0.9
1
0
0 0.2
0.3
0.4
0.5
0.6
0.7
0.8
Inlet pressure [MPa]
0.9
1
Filter Regulator
Series
AW10-A
Construction
AC
AW10-A
i
w
OUT
e
Body
2
Bonnet
Material
Colour
Zinc die-cast
White
Polyacetal
White
No.
3
Valve
r
4
Filter element
5
Piston assembly
6
Bowl O-ring
7
Bowl assembly
8
Knob
u
Drain
Description
Material
Part no.
HNBR
AR10P-090S
Non-woven fabric
AF10P-060S
Polyacetal
AR10P-150AS
NBR
C1SFP-260S
Polycarbonate
C1SF-A
Polyacetal
AR12P-030
AF + AR
y
AW + AL
Replacement Parts
AF + AFM + AR
IN
Description
1
Working Principle (Filter Regulator with Backflow Function)
q
q
IN
OUT
IN
OUT
(Inlet pressure)
(Outlet pressure)
(Inlet pressure)
(Outlet pressure)
w
AW + AFM
AW10-A
w
AW
AL
AR
AFM / AFD
When the inlet pressure is higher than the regulating pressure, the check valve operates as a normal regulator (Figure 1).
When the inlet pressure is shut off and exhausted, any inlet pressure applied to the valve q will be lost. The force for seating the valve q
is the valve spring force w only. When the valve q is opened using the outlet force, the outlet pressure will be exhausted at the inlet side
(Figure 2). When the set pressure is 0.15 MPa or less, the valve q may not open due to the valve spring w force.
Attachment
No.
q
AF + AR + AL
Component Parts
AF
t
92
AW20-B to AW60-B
Series AW20K-B to AW60K-B
Series
Construction
AW20(K)-B
AW30(K)-B/AW40(K)-B
AW60(K)-B
o
o
o
IN
w
w
y
q
w
y
q
OUT
IN
y
q
OUT
u
r
t
i
IN
u
r
t
i
OUT
r
e
Drain
t
AW20K-B to AW60K-B
Drain
(Filter Regulator with Backflow Function)
A-A
u
10
A
i
P
SH
K
SMC
U
OC
t o L
A
Drain
Component Parts
No.
1
Description
Body
2
Bonnet
3
Housing
Material
Model
Aluminium die-cast
AW20-B to AW60-B
Colour
White
Polyacetal
AW20-B to AW40-B
White
Aluminium die-cast
AW60-B
White
Aluminium die-cast
AW60-B
White
Replacement Parts
No.
Description
Material
Part no.
AW20(K)-B
AW30(K)-B
AW20P-340AS
AW30P-340AS
AW40(K)-B
AW40(K)-06-B
AW60(K)-B
4
Valve assembly
5
Filter element
Non-woven fabric
AF20P-060S
AF30P-060S
AF40P-060S
AW60P-060S
6
Diaphragm assembly
Weatherable NBR
AR20P-150AS
AR30P-150AS
AR40P-150AS
AR50P-150AS
7
Bowl seal
8
Bowl assembly Note 1)
9
Knob
10
Check valve assembly Note 3)
Brass, HNBR
AW40P-340AS
NBR
C2SFP-260S
C32FP-260S
C42FP-260S
Polycarbonate
C2SF-A
C3SF-ANote 2)
C4SF-ANote 2)
Polyacetal
AR23P-030
AR33P-030
—
AR43P-030
AR23KP-020AS
Note 1) Bowl assembly includes the bowl O-ring.
Please consult with SMC separately for psi and °F unit display specifications.
Note 2) Bowl assembly for the AW30(K)-B to AW60(K)-B models comes with a bowl guard (Material: Polycarbonate).
Note 3) Check valve assembly is applicable for a filter regulator with backflow function (AW20(K)-B to AW60(K)-B) only.
Assembly of a check valve cover, check valve body assembly and 2 mounting screws
93
AW60P-090AS
AR52P-030
Filter Regulator with Backflow Function
Series
AW20K-B to AW60K-B
Working Principle (Filter Regulator with Backflow Function)
AC
AW20K-B to AW60K-B
A-A
@
AF AR AL
A
C
AW AL
O
t o L
A
Inlet pressure
(IN)
Pressure in
diaphragm chamber
Inlet pressure
(IN)
.
.
:
:
AF AFM AR
Pressure in
diaphragm chamber
AF AR
@
@
IN
OUT
IN
OUT
Inlet pressure
Outlet pressure
Inlet pressure
Outlet pressure
Figure 1 Normal
Attachment
;
;
AW AFM
SH
Figure 2 Backflow
AW
AL
AR
AFM / AFD
When the inlet pressure is higher than the regulating pressure, the check valve w closes and operates as a normal regulator (Figure 1).
When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released
into the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator
spring e lifts the diaphragm. The valve r opens through the stem, and the outlet pressure is released to the inlet side (Figure 2).
AF
P
U
K
SMC
94
AW10-A
AW20-B to AW60-B
AW20K-B to AW60K-B
Series
Series
Series
Dimensions
AW10-A
AW20(K)-B
J
T
N
A
M
U
Bracket
(Option)
S
(Pressure gauge port size)
IN
OUT
2 x P1
(Port size)
B
B
P2
V
Q
OUT
IN
2 x P1
(Port size)
K
V
Q
C
C
F
S
F
Bracket
(Option)
R
D
S
R
J
T
N
M
D
U
A
W
W
OUT
IN
Drain
Y
IN
Z
Plate thickness
AW10-A: Max. 3.5
G
Panel fitting dimensions
Clearance for
maintenance
Panel fitting dimensions
G
Drain
Clearance for
maintenance
P2
(Pressure gauge port size)
OUT
Plate thickness
AW20(K)-B: Max. 3.5
AW30(K)-B to AW40(K)-06-B
AW60(K)-B
Bracket
(Option)
J
M
T
N
D
U
T
N
M
D
U
S
F
IN
Q
K
K
V
Q
C
R
Bracket
(Option)
R
S
C
J
OUT
IN
OUT
B
2 x P1
(Port size)
2 x P1
(Port size)
Drain
Panel fitting dimensions
IN
A
P2
W
Y
OUT
B
G
E
Clearance for
maintenance
P2
(Pressure gauge port size)
(Pressure gauge port size)
95
E
Drain
A
G
Plate thickness
AW30(K)-B: Max. 3.5
AW40(K)-B: Max. 5
Clearance for
maintenance
Z
AW10-A
Filter Regulator Series AW20-B to AW60-B
Filter Regulator with Backflow Function Series AW20K-B to AW60K-B
Width across
flats 14
S
1/8
Width across
flats 14
M5 x 0.8
1/8
AF + AR + AL
Thread type/Rc, G: ø10 One-touch fitting
Thread type/NPT: ø3/8" One-touch fitting
AW30(K)-B to AW60(K)-B
With drain guide
Width across
flats 17
1/4
Width across
flats 17
1/4
Drain cock with barb fitting
B
Barb fitting
applicable
tubing: T0604
1/4
Optional specifications
Standard specifications
Model
C Note)
D
AW10-A
AW20(K)-B
AW30(K)-B
AW40(K)-B
AW40(K)-06-B
AW60(K)-B
Round type
Round type pressure gauge
pressure gauge
(with colour zone)
P2
A
B
E
F
G
J
K
H
J
H
J
H
J
H
J
1/16
25
59.9
47.4 12.5
—
M18 x 1
25
12.5
—
—
—
—
—
ø26
26
—
—
1/8
40
87.6
72.4 26
—
M28 x 1
40
26
5
28
27
27.8
37.5
ø37.5
62.5
ø37.5
63.5
1/8
53
115.1
85.6 29.4 30
M38 x 1.5
55
29.4 3.5
28
30
27.8
40.9
ø37.5
65.9
ø37.5
66.9
1/8
70
147.1
91.7 37.3 38.4
M42 x 1.5
80
37.3 1.5
28
38.4
27.8
48.8
ø42.5
74.8
ø42.5
74.8
1/8
75
149.1
93.2 37.3 38.4
M42 x 1.5
80
37.3 1.2
28
38.4
27.8
48.8
ø42.5
74.8
ø42.5
74.8
1/8
95
234.1 170.5 47.5
—
20
47.5 3.2
28
44.3
27.8
61.3
ø42.5
80.8
ø42.5
80.8
—
Optional specifications
Model
Digital pressure
switch
Bracket mount
Q
Semi-standard specifications
With
With
With
Metal
Metal bowl
Metal bowl Metal bowl with level gauge,
auto drain barb fitting drain guide bowl with drain guide with level gauge
with drain guide
Panel mount
M
N
R
S
T
U
W
Y
Z
B
B
B
B
B
B
B
25
28
30
4.5
6.5
40
2
18
18.5
—
—
77.9
—
—
59.3
—
—
—
30
34
43.9
5.4 15.4
55
2.3
29.7 28.5
14
6
104.9
—
91.4
87.4
93.9
—
—
41
40
45.8
6.5
53
2.3
31.1 38.5
19
7
156.8
123.6
121.9
117.6
122.1
137.6
142.1
50
54
54
8.5 10.5
70
2.3
35.5 42.5
21
7
186.9
155.6
153.9
149.6
154.1
169.6
174.1
50
54
55.5
8.5 10.5
70
2.3
37
42.5
21
7
188.9
157.6
155.9
151.6
156.1
171.6
176.1
70
66
65.8 11
90
3.2
—
—
—
273.9
240.9
242.6
236.6
241.1
256.6
261.1
8
13
V
—
AR
P1
M5 x 0.8
AW10-A
1/8, 1/4
AW20(K)-B
1/4, 3/8
AW30(K)-B
1/4, 3/8, 1/2
AW40(K)-B
3/4
AW40(K)-06-B
3/4, 1
AW60(K)-B
Square type
pressure gauge
AW + AL
AW + AFM
Width across
flats 17
B
B
Dimensions
Metal bowl with level gauge,
with drain guide
B
Metal bowl with drain guide
B
Metal bowl
Metal bowl with
level gauge
B
Applicable model
Optional/Semi-standard
specifications
N.O.: Black
N.C.: Grey
B
B
B
Dimensions
O
With auto drain (N.O./N.C.)
Metal bowl with drain guide
AF + AR
With drain guide
Metal bowl
AW30(K)-B to AW60(K)-B
AF + AFM + AR
With auto drain (N.C.)
AW20(K)-B
Attachment
AW10-A /AW20(K)-B
Centre of
piping
AF
Centre of
piping
B
Centre of
piping
Applicable model
Optional/Semi-standard
specifications
J
H
H
Dimensions
Round type pressure gauge Round type pressure gauge (with colour zone)
J
AFM / AFD
Digital pressure switch
J
B
Square embedded type pressure gauge
H
Option
AC
Series
Filter Regulator
AW
AL
Note) The dimension of C is the length when the filter regulator knob is unlocked.
96
Option
Knob Cover
Prevents careless knob operation.
Lock cover
Lock (supplied by users)
Keyhole dia.: ø8
Part no.
AR20P-580AS
AR25P-580AS
AR30P-580AS
AR40P-580AS
97
Applicable model
AC20첸-B, AR20(K)-B, AW20(K)-B
AC25첸-B, AR25(K)-B
AC30첸-B, AR30(K)-B, AW30(K)-B
AC40첸(-06)-B, AR40(K)(-06)-B,
AW40(K)(-06)-B
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or
equipment damage. These instructions indicate the level of potential hazard with the
labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety
and must be followed in addition to International Standards (ISO/IEC)∗1), and other
safety regulations.
Caution:
Caution indicates a hazard with a low level of risk
which, if not avoided, could result in minor or moderate
injury.
Warning:
Warning indicates a hazard with a medium level of risk
which, if not avoided, could result in death or serious
injury.
Danger :
Danger indicates a hazard with a high level of risk
which, if not avoided, will result in death or serious injury.
∗1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
ISO 4413: Hydraulic fluid power – General rules relating to systems.
IEC 60204-1: Safety of machinery – Electrical equipment of machines.
(Part 1: General requirements)
ISO 10218-1: Manipulating industrial robots - Safety.
etc.
Warning
1. The compatibility of the product is the responsibility of the person
who designs the equipment or decides its specifications.
Since the product specified here is used under various operating conditions, its
compatibility with specific equipment must be decided by the person who designs the
equipment or decides its specifications based on necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the
responsibility of the person who has determined its compatibility with the product. This
person should also continuously review all specifications of the product referring to its
latest catalogue information, with a view to giving due consideration to any possibility of
equipment failure when configuring the equipment.
2. Only personnel with appropriate training should operate machinery
and equipment.
The product specified here may become unsafe if handled incorrectly. The assembly,
operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do
.
not service or attempt to remove
machinery/equipment until safety is confirmed.
product
and
1. The inspection and maintenance of machinery/equipment should only be performed
after measures to prevent falling or runaway of the driven objects have been
confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned
above are implemented and the power from any appropriate source is cut, and read
and understand the specific product precautions of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected
operation and malfunction.
Limited warranty and Disclaimer/
Compliance Requirements
The product used is subject to the following “Limited warranty and
Disclaimer” and “Compliance Requirements”.
Read and accept them before using the product.
Limited warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years
after the product is delivered, wichever is first.∗2)
Also, the product may have specified durability, running distance or
replacement parts. Please consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly
our responsibility, a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any
other damage incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty
terms and disclaimers noted in the specified catalogue for the particular
products.
∗2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the vacuum
pad or failure due to the deterioration of rubber material are not covered by the limited
warranty.
4. Contact SMC beforehand and take special consideration of safety
measures if the product is to be used in any of the following
conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in
a place exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation,
space, shipping, vehicles, military, medical treatment, combustion and recreation, or
equipment in contact with food and beverages, emergency stop circuits, clutch and
brake circuits in press applications, safety equipment or other applications unsuitable
for the standard specifications described in the product catalogue.
3. An application which could have negative effects on people, property, or animals
requiring special safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible
failure by using a mechanical protective function, and periodical checks to confirm
proper operation.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of
weapons of mass destruction (WMD) or any other weapon is strictly
prohibited.
2. The exports of SMC products or technology from one country to another are
governed by the relevant security laws and regulations of the countries
involved in the transaction. Prior to the shipment of a SMC product to
another country, assure that all local rules governing that export are known
and followed.
Caution
Caution
1. The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing
industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
SMC products are not intended for use as instruments for legal
metrology.
Measurement instruments that SMC manufactures or sells have not been qualified by
type approval tests relevant to the metrology (measurement) laws of each country.
Therefore, SMC products cannot be used for business or certification ordained by the
metrology (measurement) laws of each country.
Safety Instructions Be sure to read “Handling Precautions for SMC Products” (M-E03-3) before using.
SMC Corporation (Europe)
Austria
Belgium
Bulgaria
Croatia
Czech Republic
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Ireland
Italy
Latvia
+43 (0)2262622800
+32 (0)33551464
+359 (0)2807670
+385 (0)13707288
+420 541424611
+45 70252900
+372 6510370
+358 207513513
+33 (0)164761000
+49 (0)61034020
+30 210 2717265
+36 23511390
+353 (0)14039000
+39 0292711
+371 67817700
SMC CORPORATION
www.smc.at
www.smcpneumatics.be
www.smc.bg
www.smc.hr
www.smc.cz
www.smcdk.com
www.smcpneumatics.ee
www.smc.fi
www.smc-france.fr
www.smc.de
www.smchellas.gr
www.smc.hu
www.smcpneumatics.ie
www.smcitalia.it
www.smclv.lv
office@smc.at
info@smcpneumatics.be
office@smc.bg
office@smc.hr
office@smc.cz
smc@smcdk.com
smc@smcpneumatics.ee
smcfi@smc.fi
promotion@smc-france.fr
info@smc.de
sales@smchellas.gr
office@smc.hu
sales@smcpneumatics.ie
mailbox@smcitalia.it
info@smclv.lv
Lithuania
Netherlands
Norway
Poland
Portugal
Romania
Russia
Slovakia
Slovenia
Spain
Sweden
Switzerland
Turkey
UK
+370 5 2308118
+31 (0)205318888
+47 67129020
+48 (0)222119616
+351 226166570
+40 213205111
+7 8127185445
+421 (0)413213212
+386 (0)73885412
+34 902184100
+46 (0)86031200
+41 (0)523963131
+90 212 489 0 440
+44 (0)845 121 5122
www.smclt.lt
www.smcpneumatics.nl
www.smc-norge.no
www.smc.pl
www.smc.eu
www.smcromania.ro
www.smc-pneumatik.ru
www.smc.sk
www.smc.si
www.smc.eu
www.smc.nu
www.smc.ch
www.smcpnomatik.com.tr
www.smcpneumatics.co.uk
info@smclt.lt
info@smcpneumatics.nl
post@smc-norge.no
office@smc.pl
postpt@smc.smces.es
smcromania@smcromania.ro
info@smc-pneumatik.ru
office@smc.sk
office@smc.si
post@smc.smces.es
post@smc.nu
info@smc.ch
info@smcpnomatik.com.tr
sales@smcpneumatics.co.uk
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: 03-5207-8249 FAX: 03-5298-5362
1st printing TO printing TO 00 Printed in Spain
Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising