Installation Instructions - Republic Plumbing Supply

Installation Instructions - Republic Plumbing Supply
Installation
Instructions
LAKELAND
4114.100
SINGLE CONTROL KITCHEN
PULL-OUT FAUCET
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
M 9 6 8 4 7 0 R E V. 1. 5
TOOLS REQUIRED
Regular Screwdriver
1
Phillips Screwdriver
Adjustable Wrench
Plumbers' Putty or Caulking
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
Turn off hot and cold water
supplies before beginning.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
7
7
A
B
SPOUT BASE
1
3
PUTTY
2
2
3
4
SINK OR
MOUNTING
S U R FA C E
4
5
5
8
6
8
6
2
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
2
1
Faucet supplies are 21" long from faucet base.
COLD
Note: If additional supply length is
required, installer must purchase
additional parts separately.
HOT
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
3
CONNECT SPRAY HOSE
3
Slide COUPLING NUT (1) onto HOSE (2)
Place WASHER (3) into COUPLING NUT (1)
on HOSE (2). Thread COUPLING NUT (1) onto
HAND SPRAY (4) and tighten.
(May already be assembled).
1
6
5
4
Feed small end of HOSE (2) through BODY (5) so
HAND SPRAY (4) rests inside SPRAY HOLDER (6).
2
Thread HOSE END (7) onto OUTLET HOSE ADAPTER (8)
and tighten.
With HAND SPRAY (4) seated in SPRAY HOLDER (6),
install WEIGHTS (9) onto HOSE (2) using two SCREWS (10).
Locate the WEIGHTS (9) two feet (2') from the underside of
the sink deck. Tighten SCREWS (10) firmly.
24"
4
8
With HANDLE (1) down in "off"
position.
TEST INSTALLED FAUCET
Move HANDLE (1) down into "off"
position.
Turn on water supplies.
Check connections for leaks (See
Section 5).
Pull HAND SPRAY (2) from FAUCET (5)
and disconnect HAND SPRAY (2). Be
careful not to lose WASHER (7). Pull
HOSE (3) (HOSE should pull
approximately 2 feet) and direct open
HOSE END (4) into sink.
6
7
9
10
2
1
2
Operate handle up and down, in COLD and HOT positions, to
flush water lines thoroughly.
7
3
5
Place WASHER (7) into HOSE END (4) and connect
HAND SPRAY (2) to HOSE END (4). Place HAND SPRAY (2)
back into faucet.
Check HAND SPRAY (2) operation:
With faucet on push front of BUTTON (6) for a broad
cleansing spray.
4
M 9 6 8 4 7 0 R E V. 1. 5
5
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE down into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
6
SERVICE
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Pull off ESCUTCHEON CAP (4). Unscrew three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6A).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
2
3
1
4
5
HOT LIMIT SAFETY STOP ADJUSTMENT
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
6
6A
8
7
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade
screwdriver or your fingers to pull up and rotate red HOT LIMIT
SAFETY STOP (5). Follow Step "A" or "B" to adjust min./max.
discharge temperature. "0" being the hottest to "7" the coldest
temperature setting. Factory set at "0".
"A"
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten
HANDLE SCREW (1) and install INDEX BUTTON (2).
PRY RED RING FORWARD
AND ROTATE COUNTERCLOCKWISE ONE CLICK
"A"
1
3
4
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
5
6
6
"B"
2
"B"
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
0
TEMPERATURE
SETTING NUMBERS
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
5
"RED RING"- HOT
LIMIT SAFETY STOP
7
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M 9 6 8 4 7 0 R E V. 1. 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising