Sunding Bicycle Computer FUNCTIONS Computer Battery

Sunding Bicycle Computer FUNCTIONS Computer Battery
Sunding Bicycle Computer
wheel.
battery is re-installed).
SD-548B (14Functions)
Computer
Reset of Mileage Parameter
FUNCTIONS
Attach the computer to the mounting shoe by sliding the
unit until it snaps firmly into its postion. To remove it, press
the button on it in the opposite direction.
To check for proper speed function and sensor alignment,
spin the front wheel with computer in speed mode. Adjust
the position of sensor and magnet when there is no or weak
reaction.
In ODO mode, Press and hold both RIGHT and LEFT
button simultaneously for 3 seconds to clear the
circumference value and cancel (km/m) setting. The user
need to reset the tyre circumference, and (km/m), the
original ODO value and CLOCK will remain unaffected.
-
SPD
CURRENT SPEED
ODO ODOMETER (0.001~99999km/m)
DST
TRIP DISTANCE
MXS MAXIMUM SPEED
AVS
AVERAGE SPEED
TM
ELAPSED TIME .
CLK CLOCK (12H/24H)
SCAN
“+” “-” COMPARATOR
SETTING SPEED SCALE(km/h,m/h)
SETTING TYRE CIRCUMFERENCE : (0mm ~
9999mm)
SETTING
THE
LAST
VALUE
OF
ODOMETER/ODO
FREEZE FRAME MEMORY
AUTO ON/OFF
Computer Battery Installation
Remove the battery cover from the bottom of the computer
by using a flat blade screwdriver, install an AG13 battery
with the positive (+) pole facing the battery cover and
replace the cover. Should the LCD show irregular figures,
take out the battery and re-install it.
Speedometer Sensor
Attach the speedometer sensor bracket to the left fork blade,
using the shims to adjust the diameter, and using the cable
ties (show below) to tie it with the fork. Position the sensor
and magnet as show; make sure that the arc of the magnet
intersects the alignment mark on the sensor with 1mm
clearance.
Wheel Size Input
‘2060’ appears on the screen when the battery has been
installed, with one figure flashing, choose the correct wheel
circumference from the table below. Press RIGHT button to
advance digits as needed and LEFT button to confirm and
TIRE SIZE
700c x 38mm
700c x 35mm
700c x 32mm
700c x 30mm
700c x 28mm
700c x 25mm
700c x 23mm
700c x 20mm
700cTubulari
650c x 23mm
650c x 20mm
27’’ x 1-1/4’’
27’’ x 1-1/8’’
26’’ x 2.3’’
CIRC
2180
2168
2155
2145
2136
2124
2105
2074
2130
1990
1945
2161
2155
2135
TIRE SIZE
26’’ x 2.25’’
26’’ x 2.1’’
26’’ x 2.0’’
26’’ x 1.9’’/1.95’’
26’’ x 1.75’’
26’’ x 1.5’’
26’’ x 1.25’’
26’’ x 1.0’’
24’’ x 1.9’’/1.95’’
20’’ x 1-1/4’’
16’’ x 2.0’’
16’’ x 1.95’’
16’’ x 1.5’’
CIRC
2115
2095
2074
2055
2035
1985
1953
1913
1916
1618
1253
1257
1206
advance. (The circumference ranges 0mm~9999mm),press
LEFT button to enter KM/M mode.
Setting(
(km/h)
)/(
(m/h)
)
Press the RIGHT button to choose km/h
or m/h. Press the LEFT button to enter
CLOCK mode.
CLK Mode(12H/24H)
Mounting Shoe
Attach the mounting shoe
with the cable ties to the
handlebar,
adjust
the
mounting shoe on the
handlebar with the shims to
hold its position.
Sensor Wiring
Route the sensor wire up the fork
blade, using cable ties to secure it
at the bottom and crown to avoid it
hinder the movement of the front
In CLOCK Mode, press the LEFT button
for 3 seconds to enter 12/24H selection.
Re-press the LEFT button for 12/24
exchanging. Press the RIGHT button to
enter Hour setting mode, when the figure
indicating HOUR start to flash, press the
LEFT button to adjust it.
Continue to press the RIGHT button to enter Minute setting
mode, when the figure indicating MINUTE start to flash,
press the LEFT button to adjust it and RIGHT button to
confirm, re-press RIGHT button to enter ODO mode.
Setting the Last value of Odometer
In ODO mode, press the LEFT
button for 2 seconds to set the ODO
value, its initial value is 0000.0.
when one figure flashing, press
RIGHT button to adjust it and LEFT
button to confirm it, and start to set the next
figure.(after re-install the battery, latest value can
be inputted according to the value exists before the
Speedometer
SCAN
In Scan mode , DST, MXS, AVS and TM
mode are indicated in turn every 4
seconds.
Press the RIGHT button to enter CLOCK
Mode.
Sleep Mode
Speed is shown all the time on the screen, its maximum
reading is 99.9km/h(m/h), and it is accurate to +/- 0.1km/h
(m/h).
If no signal has been inputted for 300 seconds, computer
will enter into Sleep Mode,and CLK value remains. It will
turn back to the former mode with all the data collected then
when any signal is inputted or any button is pressed.
Speed Comparator
FREEZE FRAME MEMORY
During riding , ‘+’and ‘-’ indicates the current speed is
higher or lower than average speed(AVS) .
Press the LEFT button in any time will enter into freeze
frame memory mode. Flashing TM data will appear on the
screen. Press the RIGHT button to view the records of DST,
MXS,AVS,TM.
Press the LEFT button to end it.
Odometer
In ODO mode , the total distance is
indicated on the screen, its mileage range
is 0.001~99999km(m). The display will
be back to 0 when value exceeds its
maximum limit, press the RIGHT button to enter DST
mode.
Trip Distance (DST)
In DST mode, the distance for one trip is
indicated
on the bottom line. DST
ranges from 0~99999km(m), when the
value exceed the range limit, it restarts from
0 automatically. Both the time and the
distance records will be cleared when the time of one trip
exceed the range limited.
press the LEFT button for 5 seconds, the computer will
clear the records of DST,MXS,AVS,TM to 0.
Press the RIGHT button to enter MXS mode.
Buttons Instruction
Press the RIGHT button to choose any mode below :
ODO, DST, MXS, AVS, TM, SCAN(DST、MXS、AVS、
TM) and CLOCK. It’s unnecessary to press the LEFT
button except choosing the Freeze frame Memory mode.
In Freeze Frame Momery mode, press the RIGHT button,
several data will display, re-press LEFT button to turn back
to other modes.
Malfunctions and Problems
Malfunctions
No speedometer
Inaccurate value is
indicated
Slo w d i s p lay
response
Maximum Speed (MXS)
In MXS mode, maximum speed is
indicated on the bottom line. Press the
LEFT button for 5 seconds to clear the
records of, MXS,DST,AVS,TM to 0.
Press the RIGHT button to enter AVS mode.
Average Speed
In AVS mode, average speed is indicated
on the bottom line. Press the LEFT button
for 5 seconds to clear the records of
AVS,DST,MXS,TM to 0.
Press RIGHT button to enter TM mode.
Trip Time
In TM mode, trip time is indicated on the
bottom line. TM ranges 0 :00 :00 ~
99 :59 :59. It will be back to 0 when
value exceed the limits.
Press the LEFT button for 5 seconds to clear the records of
TM, DST, MXS and AVS to 0.
Press the RIGHT button to enter SCAN mode.
Black display
Weak display
Display shows
Irregular figures
Accessories
Problems
Improper magnet/sensor alignment
Improper input, such as wheel
circumference.
Temperature exceeds operating
limits(0℃~55℃).
Temperature too high, or put in
direct sunlight for too long time.
Need back to shadow place for a
period.
Poor battery contact or dead battery.
Take out battery and reinstall it after
10 seconds.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising