Dome Camera
Dome Camera
User Manual
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.”
1
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
2
municipal waste in the European Union. For proper recycling,
return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.
3
Table of Contents
1 Introduction .................................................................. 5
1.1 Product Features ..................................................5
1.2 Overview .............................................................6
2 Installation ................................................................... 7
2.1 Ceiling Mounting ..................................................7
2.2 Ceiling Mounting with a gang box ......................... 11
2.3 Wall Mounting .................................................... 14
2.4 Side Conduit Cabling ........................................... 17
2.5 Wiring ............................................................... 19
4
1 Introduction
1.1 Product Features
This series of camera adopts high-sensitive sensor and advanced
circuit board design technology. It possesses of high resolution,
low distortion, and low noise features, etc. It is extremely suitable
for surveillance system and image process system.
The main features are as follows:

Adopt high-performance SONY CCD, up to 700TVL
resolution, providing high definition and clear image

OSD menu, which enables user to configure the detailed
parameters

Support Digital Wide Dynamic Range (D-WDR) for
backlighting surveillance

Auto-white balance with high color rendition

High Signal Noise Ratio (SNR), which brings clear and
high-quality image

Auto electronic shutter control to adapt to the different
surveillance environments

Auto gain control, adaptive brightness

Auto-iris

Support up to 8 configurable privacy masks to ensure your
privacy
5
Advanced 3-axis design allows this dome camera to be

adjusted 0-355°horizontally and 0-75°vertically to meet
different mounting requirements
1.2 Overview
3
1
5
6
4
7
2
Figure 1-1 Overview
1 Black Liner
5 Power Cable
2 Lower Dome
6 Video Cable
3 AUX Interface
7 Lens
4 Menu Button
8 Adapter Ring
6
8
2 Installation
Before you start:
Please make sure that the device in the package is in good
condition and all the assembly parts are included.
This series of camera support ceiling mounting, ceiling mounting
with a gang box, wall mounting and side conduit mounting.
2.1 Ceiling Mounting
Note:
Please make sure that the ceiling is strong enough to withstand
three times the weight of the camera.
Steps:
1. Attach the drill template (supplied) to the place where you
want to fix the camera.
2. Drill 3 screw holes and one cable hole (if you want to route the
cable through the mounting base) according to the drill
template.
7
Side Cable Outlet
Cable Outlet
Screw Hole
Screw Hole
Drilling Template for Outdoor
Day/Night Vandal-proof Dome Camera
Screw Hole
Figure 2-1 The Drill Template
3. Loosen the screws with the supplied L-shape screwdriver to
open the lower dome.
4. Remove the black liner.
Figure 2-2 Remove the Black Liner
8
Note:
If you want to install the camera to the cement ceiling, you need to
screw 3 expansion screws into the 3 drilled holes first.
5. Route the cables and connect the power supply and output the
video on a monitor.
6. Secure the dome camera to the ceiling with 3 self-tapping
screws. Refer to Figure 2-3.
Figure 2-3 Secure the Camera to the Ceiling
7. Adjust the Lens.
1). View the camera image via the monitor.
2). Loosen the lock screw besides the lens.
3). Rotate the panning table to adjust the panning position of
the camera. 0 to 355°is adjustable.
9
4). Rotate the tilting table to adjust the tilting position of the
camera. 0 to 75°is adjustable.
5). Rotate the lens to adjust the azimuth angle of the image. 0
to 355°is adjustable.
6). Tighten the lock screw.
7). Move the focus lever and zoom lever to adjust the focus
and the zoom.
Pan
Tilt
Rotation
Figure 2-4 Lens Adjustment
8. Attach the black liner back to the camera.
9. Attach the lower dome back to the camera and secure it with
the screws.
Figure 2-5 Install the Black Liner and the Lower Dome
10
10. Remove the protection film softly to complete the installation.
Note:
Remove the protection film after the installation is completed in
case of the image problem caused by the scrape of the lower
dome.
2.2 Ceiling Mounting with a gang box
Steps:
1. Secure the adapter ring to the gang box.
Figure 2-6 Secure the Adapter Ring
2. Loosen the screws to open the lower dome.
3. Remove the black liner.
11
Figure 2-7 Remove the Black Liner
4. Route the cables and connect the power supply and output the
video on a monitor.
5. Secure the camera to the adapter ring with the screws.
Figure 2-8 Install the Camera
6. Adjust the lens.
1). View the camera image via the monitor.
12
2). Loosen the lock screw besides the lens.
3). Rotate the panning table to adjust the panning position of
the camera. 0 to 355°is adjustable.
4). Rotate the tilting table to adjust the tilting position of the
camera. 0 to 75°is adjustable.
5). Rotate the lens to adjust the azimuth angle of the image. 0
to 355°is adjustable.
6). Tighten the lock screw.
7). Move the focus lever and zoom lever to adjust the focus
and the zoom.
7. Attach the black liner back to the camera.
Figure 2-9 Attach the Black Liner
8. Attach the lower dome back to the camera and secure it with
the screws.
13
Figure 2-10 Install the Lower Dome
9. Remove the protection film softly to complete the installation.
Note:
Remove the protection film after the installation is completed in
case of the image problem caused by the scrape of the lower
dome.
2.3 Wall Mounting
Note:
Please make sure that the wall is strong enough to withstand three
times the weight of the camera.
Steps:
1. Drill four expansion screw holes on the wall.
2. Secure the mount to the wall with the expansion screws.
3. Insert the adapter ring to the mount.
14
Figure 2-11 Install the Mount and the Adapter Ring
4. Loosen the screws to open the lower dome.
5. Remove the black liner.
6. Secure the camera to the adapter ring.
Figure 2-12 Install the Camera
7. Route the cables and connect the power supply and output the
video on a monitor.
15
8. Adjust the Lens.
1). View the camera image via the monitor.
2). Loosen the lock screw besides the lens
3). Rotate the panning table to adjust the panning position of
the camera. 0 to 355°is adjustable.
4). Rotate the tilting table to adjust the tilting position of the
camera. 0 to 75°is adjustable.
5). Rotate the lens to adjust the azimuth angle of the image. 0
to 355°is adjustable.
6). Tighten the lock screw.
7). Move the focus lever and zoom lever to adjust the focus
and the zoom.
9. Attach the black liner back to the camera.
Figure 2-13 Install the Black Liner
10. Attach the lower dome back to the camera and secure it with
the screws.
16
Figure 2-14 Install the Lower Dome
11. Remove the protection film softly to complete the installation.
Note:
Remove the protection film after the installation is completed in
case of the image problem caused by the scrape of the lower
dome.
2.4 Side Conduit Cabling
There are two cabling methods selectable for this series of camera.
One is to route the cable through the ceiling, and the other is to
route the cable though the side conduit.
Steps:
1. Unscrew the water-proof plug shown below.
17
Figure 2-15 Unscrew the Water-proof Plug
2. Route the power/video cables through the water-proof plug to
the conduit.
3. Connect the corresponding power/video cables.
4. Screw the conduit to the water-proof plug to complete the
installation.
Figure 2-16 Connect the Conduit to the Camera
18
2.5 Wiring
Figure 2-17 The Power/Video Cable (Two-pins Power Interface)
Notes:

Please make sure that the power adapter can match with the
camera.

The standard power supply of the camera is 12V DC or 24V
AC (Please refer to technical specifications for more details).
Figure 2-18 The Power/Video Cable
Notes:

Please make sure that the power adapter can match with the
camera.

The standard power supply of the camera is 12V DC (Please
refer to technical specifications for more details).
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising