Iris Carrier Board Datasheet

Iris Carrier Board Datasheet
Iris V1.1
Datasheet
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 1
Iris Carrier Board Datasheet
Revision History
Date
25-Sept-15
Doc. Rev.
Iris Version
Rev. 1.0
V1.1
Changes
Initial Release: Datasheet has been updated to new format.
Please note: FF UART has been renamed to UART-A, BT UART to
UART-B and STD UART to UART-C.
07-July-16
Rev. 1.1
V1.1
Section 2.2, Hardware Architecture Block Diagram: Updated block
diagram (fig 1).
04-Aug-16
Rev. 1.2
V1.1
Section 2.2, Hardware Architecture Block Diagram: Updated block
diagram (fig 1).
30-Sept-16
Rev. 1.3
V1.1
Section 2.2, Hardware Architecture Block Diagram: Updated block
diagram (fig 1).
07-Feb-17
Rev. 1.4
V1.1
Section 1.1, Reference Documents: Updated web-links.
Section 3.7.2, Unified Interface Display Connector (X3): Updated weblinks.
Section 3.10.2, Battery Holder (BAT1): Added note regarding battery
holder spring contact issue.
Section 7, Design data: Updated web-links.
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 2
Iris Carrier Board Datasheet
Contents
1.
Introduction ........................................................................................................ 5
1.1. Reference Documents ................................................................................................................. 5
2.
1.1.1
Colibri Computer Modules .................................................................................... 5
1.1.2
Synchronous DC/DC Buck Converter .................................................................... 5
1.1.3
USB, Current Limiter, Power Distribution Switches .................................................. 5
1.1.4
LVDS Transmitter, FPD-Link ................................................................................ 5
1.1.5
Video DAC, Parallel RGB to VGA .......................................................................... 5
Features ............................................................................................................ 6
2.1. Overview ...................................................................................................................................... 6
2.2. Hardware Architecture Block Diagram ......................................................................................... 7
2.3. Physical Drawings ........................................................................................................................ 8
2.3.1
Top Side Connectors: Physical Drawing ................................................................. 8
2.3.2
Bottom Side Connectors: Physical Drawing ............................................................ 9
2.4. Assembly Options ...................................................................................................................... 10
3.
2.4.1
Iris Assembly Options – Top Side ........................................................................ 10
2.4.2
Iris Assembly Options – Bottom Side ................................................................... 11
Interface Description .......................................................................................... 12
3.1. Colibri Computer-On-Module ..................................................................................................... 12
3.1.1
Colibri SODIMM Connector (X1) ......................................................................... 12
3.1.2
Boot Mode header (JP1) .................................................................................... 12
3.2. Power Supply ............................................................................................................................. 12
3.2.1
Terminal Block Power Supply Connector (X17) ..................................................... 12
3.2.2
Power Out Header (X20) .................................................................................... 12
3.3. Indications .................................................................................................................................. 13
3.4. Ethernet ...................................................................................................................................... 13
3.4.1
Ethernet Connector (X15) ................................................................................... 13
3.4.2
Central Tab Jumper (JP2) .................................................................................. 13
3.5. USB Interface ............................................................................................................................. 14
3.5.1
USB Host (X11) ................................................................................................ 14
3.5.2
USB Host/Client (X12) ....................................................................................... 14
3.6. SD/MMC Interface ...................................................................................................................... 14
3.6.1
Micro SD Card Holder (X10) ............................................................................... 14
3.7. Display Interface ........................................................................................................................ 15
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 3
Iris Carrier Board Datasheet
3.7.1
DVI FFC connector (X2) ..................................................................................... 16
3.7.2
Unified Interface Display Connector (X3) .............................................................. 17
3.7.3
DVI-I Connector (X4) ......................................................................................... 18
3.7.4
LVDS Connector (X7) ........................................................................................ 19
3.8. Audio Interface ........................................................................................................................... 20
3.8.1
Audio Jack (X8) ................................................................................................ 20
3.8.2
Audio Header (X9)............................................................................................. 20
3.9. Digital and Analog I/O Interface ................................................................................................. 21
3.9.1
UART-A RS-232 header (X13) ............................................................................ 21
3.9.2
UART-B/C RS-232 header (X14) ......................................................................... 21
3.9.3
Extension Connector (X16) ................................................................................. 22
3.9.4
Touch Connector (X19) ...................................................................................... 23
3.10. Real-Time Clock (RTC) .............................................................................................................. 24
4.
3.10.1
External RTC .................................................................................................... 24
3.10.2
Battery Holder (BAT1)........................................................................................ 24
Electrical Characteristics .................................................................................... 25
4.1. Electrical Specifications ............................................................................................................. 25
5.
Temperature Range .......................................................................................... 25
5.1. Operating Temperature Range .................................................................................................. 25
6.
Mechanical Data ............................................................................................... 26
6.1. Iris Dimensions – Top Side ........................................................................................................ 26
6.2. Iris Dimensions – Bottom Side ................................................................................................... 27
7.
Design Data ..................................................................................................... 28
8.
Product Compliance .......................................................................................... 28
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 4
Iris Carrier Board Datasheet
1. Introduction
Iris is a carrier board for the Colibri family of computer-on-modules. Iris supports all modules in the
Colibri product family, and includes support for the additional/enhanced functionality available on the
latest products in Colibri family.
1.1. Reference Documents
For detailed technical information about the suitable computer modules, please refer to the sections
below:
1.1.1
Colibri Computer Modules
An overview of the Colibri product family:
https://www.toradex.com/computer-on-modules/colibri-arm-family
1.1.2
Synchronous DC/DC Buck Converter
http://www.ti.com/product/tps51120
1.1.3
USB, Current Limiter, Power Distribution Switches
http://www.ti.com/product/tps2042b
1.1.4
LVDS Transmitter, FPD-Link
http://www.ti.com/product/ds90c363b
1.1.5
Video DAC, Parallel RGB to VGA
http://www.analog.com/en/products/digital-to-analog-converters/da-converters/adv7125.html
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 5
Iris Carrier Board Datasheet
2. Features
2.1. Overview
Iris carrier board provides the following features and communication interfaces:

USB Type-A and OTG Micro-AB connectors for host and host/client

RJ45 Ethernet

Micro SD card slot

Digital (TDMS) and Analog (VGA) interfaces on a single DVI-I connector

LVDS interface

Digital RGB interface

Audio out on 3.5mm stereo jack

Microphone In and Line-In on audio header

SSP, I2C, 4 ADCs, 4 PWMs and 8 GPIOs on extension header

UART-A/B/C available with TTL and RS-232 level

Real-time clock with battery backup

Resistive touch screen connector
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 6
Iris Carrier Board Datasheet
2.2. Hardware Architecture Block Diagram
* This is a module-specific feature and may not be supported by all the computer-on-modules in the Colibri family.
For more details, refer to the datasheet of Colibri computer-on-modules.
Fig.1 Iris Carrier Board Hardware Architecture
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 7
Iris Carrier Board Datasheet
2.3. Physical Drawings
2.3.1
Top Side Connectors: Physical Drawing
Unified Interface
Display FFC
DVI FFC
Touch Connector
X16
Power Supply
Connector
X17
JP1 X20
X19
Battery
Holder
Extension Connector
BAT1
X13
UART-A
RS-232
X1
X9
Reset
Switch
SW1
X11
USB
X4
DVI-I
JP2
X8
X12
Audio Micro
Jack
USB
UART-B/C
RS-232
X14
X7
X15
Ethernet
Micro SD
Card Holder
Fig. 2 Iris Carrier Board Connectors – Top Side
Ref.
Description
Remarks
X1
Colibri SODIMM connector
X4
DVI-I connector
X7
LVDS connector
X8
Audio Jack
X9
Audio header
X11
USB Host
X12
USB Host/Client
X13
UART-A RS-232 header
X14
UART-B/C RS-232 header
X15
Ethernet connector
X16
Extension connector
X17
Power Supply connector
X19
Touch connector
X20
Power Out header
Not populated
BAT1
12mm Battery holder
Supported batteries: BR1216, CR1216, BR1220, CL1220, CR1220,
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 8
Iris Carrier Board Datasheet
BR1225
SW1
Reset Button
JP1
Boot Mode header
JP2
Central Tab jumper
2.3.2
Not populated
Bottom Side Connectors: Physical Drawing
DVI FFC
Unified Interface
Display Connector
X2
X3
X10
Micro SD
Card Holder
Fig. 3 Iris Carrier Board Connetors – Bottom Side
Ref.
Description
X2
DVI FFC connector
X3
Unified Interface Display Connector
X10
Micro SD Card Holder
Remarks
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 9
Iris Carrier Board Datasheet
2.4. Assembly Options
This section marks/highlights the components on the Iris carrier board that can be used to configure
different features and functional options.
WARNING:


2.4.1
Changing the PCB assembly voids the product warranty.
Toradex doesn’t take any responsibility for malfunction or damages caused by changing any
assembly option.
Iris Assembly Options – Top Side
LED2 LED1
R63
R43
R75
R91
R88
R37
R45
R41
R46 R42
R44 R40
Fig.4 Iris Carrier Board Assembly Options – Top Side
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 10
Iris Carrier Board Datasheet
2.4.2
Iris Assembly Options – Bottom Side
R21
R19
R20
R22
R110
R16 R23
R113
R112
R111
R17 R14 R18 R15
R109
Fig.5 Iris Carrier Board Assembly Options – Bottom Side
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 11
Iris Carrier Board Datasheet
3. Interface Description
3.1. Colibri Computer-On-Module
3.1.1
Colibri SODIMM Connector (X1)
Type:
SODIMM 200 Socket
Manufacturer: Tyco Electronics-1473005-1
Refer to the Colibri datasheets for pin-out assignment details of the Colibri modules.
3.1.2
Boot Mode header (JP1)
This is an unpopulated 2.54mm (pitch) pin which provides the signals required to boot the Colibri T20
and T30 module into recovery mode (this is not functional on all other Colibri modules e.g. PXAxxx or
VFxx).
Connector type: 1x3 Pin Header Male, 2.54mm, Not assembled
Pin
Signal Name
Remarks
1
RECOVERY
By shorting the pin 1-2 the Colibri will boot in Recovery boot mode.
2
GND
3
SD_BOOT
By shorting the pin 2-3 the Colibri will boot in SD boot mode.
The following table describes the assembly options available on the Iris carrier board with respect to
the SD Boot (only with Colibri T20):
Assembled
Components
on Iris V1.1
Solution Selected
Assembly Options
SD Boot Mode
Assemble 100R resistors R109, R111, R112 and R113.
PCB Side
Bottom
Please refer to figure 5 in Section 2.4, Assembly Options for the position of the resistors.
3.2. Power Supply
Iris carrier board has a wide input voltage range of 6-27V DC. The supply is protected against reverse
input voltage polarity and short circuits.
The on-board power supply provides the following supplies (maximum power).
5V / 3.5A
3.3V / 2.5A
3.2.1
(17.5W)
(8.25W)
Terminal Block Power Supply Connector (X17)
Connector type: Tyco 284512-2
Pin
Description
1
GND_IN
2
PWR_IN
3.2.2
Voltage / range
6 – 27V
Power Out Header (X20)
Connector type: 1x3 Pin Header Male, 2.54mm, Not assembled
Pin
Description
1
+5V
2
GND
3
+3.3V
Voltage / range
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 12
Iris Carrier Board Datasheet
3.3. Indications
There are two LEDs on the top side of the PCB; they are tuned on if the power supply circuit is
correctly providing 3.3 and 5V power rails.
Ref.
Description
LED1
3.3V
LED2
5V
Please refer to the figure 4 in Section 2.4, Assembly Options for the position of the LEDs.
3.4. Ethernet
3.4.1
Ethernet Connector (X15)
Connector type: RJ-45, Pulse J00-0065NL
Pin
Signal Name
SODIMM Pin Number
I/O Type
Voltage
Pull-up/Pull-down
1
ETH_TX0_P
189
O
+3.3V
50R to ETH_AVCC
2
ETH_TX0_N
187
O
+3.3V
50R to ETH_AVCC
3
ETH_RXI_P
195
I
+3.3V
4
ETH_AVCC (CT_TXD)
PWR
5
ETH_AGND (CT_RXD)
PWR
6
ETH_RXI_N
7
NC
8
SHIELD
9
+3.3V
10
ETH_LINK_ACT
183
I
+3.3V
11
ETH_SPEED
185
I
+3.3V
12
+3.3V
S1
SHIELD
S2
SHIELD
3.4.2
193
I
+3.3V
PWR
PWR
Central Tab Jumper (JP2)
Jumper JP2 should be configured based upon the Ethernet controller which is present on the installed
Colibri module.
Header pin pitch: 2.54 mm
Jumper position
Description
1-2
Use this configuration for DM9000E on PXA270
2-3
Use this configuration for DM9000A/ASIX on other modules
Please refer to the figure 4 in Section 2.4, Assembly Options for the position of the Jumper (JP2).
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 13
Iris Carrier Board Datasheet
3.5. USB Interface
3.5.1
USB Host (X11)
The Iris carrier board features 1x USB 2.0 host interface using a USB 2.0 type-A connector X11. The
USB interface supports USB 2.0 high-speed and can operate at a maximum of 480 Mbit/s, depending
on the Colibri module being used.
Connector type: FCI 73725-0110BLF
Pin
Signal Name
1
VCC_USB1
2
USBH_N
141
3
USBH_ P
139
4
GND
S1
SHIELD
S2
SHIELD
3.5.2
SODIMM Pin Number
I/O Type
Voltage
PWR
+5V
Pull-up/Pull-down
I/O
15K to GND
I/O
15K to GND
PWR
USB Host/Client (X12)
The Iris carrier board features 1x USB host/client interface using a Micro AB type USB connector X12.
Connector type: Molex 47589-0001
Pin
Signal Name
SODIMM Pin Number
I/O Type
Voltage
PWR
+5V
Pull-up/Pull-down
1
VCC_USB2
2
USBC_N
145
I/O
15K to GND
3
USBC_P
143
I/O
15K to GND
4
USB ID
5
GND
S1
SHIELD
S2
SHIELD
S3
SHIELD
S4
SHIELD
PWR
3.6. SD/MMC Interface
3.6.1
Micro SD Card Holder (X10)
Connector type: Amphenol 101-00581-59
Pin
Signal Name
SODIMM Pin Number
I/O Type
Voltage
Pull-up/Pull-down
1
2
MM_DAT_2
51
I/O
+3.3V
68K to +3.3V
MM_DAT_3
53
I/O
+3.3V
68K to +3.3V
3
MM_CMD
190
I
+3.3V
33K to +3.3V
4
+3.3V
PWR
+3.3V
5
MM_CLK
I
+3.3V
6
GND
7
MM_DAT_0
192
I/O
+3.3V
68K to +3.3V
8
MM_DAT_1
49
I/O
+3.3V
68K to +3.3V
CD1/2 MM_CD
S1
SHIELD
S2
SHIELD
47
PWR
43
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 14
Iris Carrier Board Datasheet
3.7. Display Interface
Iris carrier board provides many options for connecting LCD panels and monitors, with the following
three interfaces supported:
 18 bit digital RGB
 LVDS
 DVI-I (Digital TDMS and Analog VGA)
DVI
DVI-I connector
VGA
VGA
VGA DAC
upto 140MHz
VGA source selection
(zero ohm link assembly option)
Colibri DVI/VGA FFC
connector
(Tegra
(ColibriT20
Txxonly)
and
iMX6 (HDMI only))
18 bit LVDS converter
(NS DS90C363B)
VGA
LVDS connector
(DF13 20 way 1mm pitch)
LVDS
Digital RGB
Colibri digital RGB interface
Digital RGB FFC
Fig.5 Display Interface Architecture
The combination of display interfaces which are available are dependent upon the Colibri module
which is installed:
 The Colibri Txx and iMX6 is able to drive two independent displays on the following
combination of display interfaces:

o DVI and VGA
o DVI and LVDS
o DVI and RGB
The Colibri PXAxxx, VFxx are able to drive single display on the following display interfaces:
o
o
o
RGB
LVDS
VGA
It is possible to select, using an assembly option, whether the VGA output from the Colibri T20 FFC or
VGA DAC (generated from the RGB interface) is connected to the analogue VGA of the DVI-I
interface.
The default configuration connects the output of the on-board VGA DAC to the DVI-I connector.
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 15
Iris Carrier Board Datasheet
The following table describes the assembly options available on the Iris carrier board with respect to
the DVI-I Interface:
Assembled
Components
on Iris V1.1
PCB Side
Assemble resistors R14, R15, R16, R19, and R20.
Disassemble resistors R17, R18, R21, R22, and R23.
R14, R15, R16,
R19, R20
Bottom
Assemble resistors R17, R18, R21, R22, and R23.
Disassemble resistors R14, R15, R16, R19, and R20.
R14, R15, R16,
R19, R20
Bottom
Solution Selected
Assembly Options
Use the RGB to VGA DAC
signals
Use the Colibri T20 FFC
VGA signals
Please refer to figure 5 in Section 2.4, Assembly Options for the position of the resistors.
Note:

3.7.1
Assembly options for the selection of VGA output apply only to Colibri T20 (only WinCE).
DVI FFC connector (X2)
Connector type: Molex 52435-2471
Pin
Signal Name
SODIMM Pin Number
I/O Type
Voltage
Pull-up/Pull-down
1
GND
2
TMDS_CLK_P
I
+3.3V
3
TMDS_CLK_N
I
+3.3V
4
GND
5
TMDS_DATA0_P
I
+3.3V
6
TMDS_DATA0_N
I
+3.3V
7
GND
8
TMDS_DATA1_P
I
+3.3V
9
TMDS_DATA1_N
I
+3.3V
10
GND
11
TMDS_DATA2_P
I
+3.3V
12
TMDS_DATA2_N
I
+3.3V
13
NC
14
HOTPLUG_DETECT
O
+3.3V
15
DDC_CLK
I
+5V
1.8K to +5V
16
DDC_DATA
I
+5V
1.8K to +5V
17
GND
18
CRT_RED
19
GND
20
CRT_GREEN
21
GND
22
CRT_BLUE
I
+3.3V
23
CRT_VSYNC
I
+3.3V
24
CRT_HSYNC
I
+3.3V
PWR
PWR
PWR
PWR
PWR
I
+3.3V
PWR
I
+3.3V
PWR
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 16
Iris Carrier Board Datasheet
3.7.2
Unified Interface Display Connector (X3)
Iris carrier board provides a digital RGB interface port (18-bpp) to interface with the LCD panels using
a 40-way, Unified Interface Display connector (X3). It also includes a 4-wire resistive touch screen
interface on the same FFC connector.
The Unified Interface Display connector (X7) is compatible with the EDT Unified TFT Interface. A
variety of LCD panels with integrated touch support for evaluation purposes are available at the
Toradex Webshop.
For customers looking for capacitive touch display solution, Iris carrier boards are fully compatible with
the Toradex Capacitive Multi-Touch Display solution. Please refer to the following developer page link
for more details:

http://developer.toradex.com/products/capacitive-multi-touch-display
For more TFT display solutions, refer to the following developer webpage articles:



http://developer.toradex.com/knowledge-base/supported-displays
http://developer.toradex.com/knowledge-base/tianma-rgb-display-adapter-board
http://developer.toradex.com/knowledge-base/generic-rgb-display-adapter-board
Connector type: Omron XF2M-4015-1A
Color Mapping
18bpp
SODIMM
Number
Pin
Signal Name
I/O Type
Voltage
1
GND
PWR
2
GND
PWR
3
+3.3V
PWR
+3.3V
4
+3.3V
PWR
+3.3V
5
BL_ON
71
O
+3.3V
6
PWM_A
59
O
+3.3V
7
RESET_OUT#
87
O
+3.3V
8
LCD_D_5
BLUE 5
72
O
+3.3V
9
LCD_D_4
BLUE 4
78
O
+3.3V
10
LCD_D_3
BLUE 3
58
O
+3.3V
11
LCD_D_2
BLUE 2
60
O
+3.3V
12
LCD_D_1
BLUE 1
70
O
+3.3V
13
LCD_D_0
BLUE 0
76
O
+3.3V
14
GND
15
LCD_D_11
GREEN 5
50
O
+3.3V
16
LCD_D_10
GREEN 4
74
O
+3.3V
17
LCD_D_9
GREEN 3
48
O
+3.3V
18
LCD_D_8
GREEN 2
62
O
+3.3V
19
LCD_D_7
GREEN 1
46
O
+3.3V
20
LCD_D_6
GREEN 0
80
O
+3.3V
21
GND
22
LCD_D_17
RED 5
61
O
+3.3V
23
LCD_D_16
RED 4
57
O
+3.3V
24
LCD_D_15
RED 3
64
O
+3.3V
25
LCD_D_14
RED 2
66
O
+3.3V
26
LCD_D_13
RED 1
54
O
+3.3V
27
LCD_D_12
RED 0
52
O
+3.3V
28
LCD_PCLK_WR
56
O
+3.3V
Pull-up/
Pull-down
PWR
PWR
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 17
Iris Carrier Board Datasheet
Color Mapping
18bpp
SODIMM
Number
Pin
Signal Name
I/O Type
Voltage
29
GND
30
LCD_LCLK_A0
68
O
+3.3V
31
LCD_FCLK_RD
82
O
+3.3V
32
LCD_BIAS
44
O
+3.3V
33
Connected to 3.3V or GND via
assembly option. The default
assembly is GND
O
+3.3V/GND
34
Connected to 3.3V or GND via
assembly option. The default
assembly is GND
O
+3.3V/GND
35
GND
36
+3.3V
PWR
+3.3V
37
TOUCH_TSPY
18
O
+3.3V
38
TOUCH_TSMX
16
O
+3.3V
39
TOUCH_TSMY
20
O
+3.3V
40
TOUCH_TSPX
14
O
+3.3V
Pull-up/
Pull-down
PWR
PWR
The following table describes the assembly options available on the Iris carrier board with respect to
the Unified Inferface Display:
Solution Selected
Assembly Options
Unified Interface Display ,
Rotate display
Assemble appropriate 0R resistors R43, R63, R75, and
R91. Refer to LCD TFT datasheet for configuration
details.
Assembled
Components
on Iris V1.1
PCB Side
R63, R91
Bottom
Please refer to figure 5 in Section 2.4, Assembly Options for the position of the resistors.
3.7.3
DVI-I Connector (X4)
Connector type: Molex 74320-1004
Pin
Signal Name
Description
I/O Type
Voltage
1
TMDS_DATA2_N
The negative DVI output number 2
O
2
TMDS_DATA2_P
The positive DVI output number 2
O
3
GND
4
NC
Not connected
5
NC
Not connected
6
DDC_CLK
DVI EDID Clock signal
O
+5V
7
DDC_DATA
DVI EDID Data signal
I/O
+5V
8
CRT_VSYNC
O
+5V
9
TMDS_DATA1_N
The negative DVI output number 1
O
10
TMDS_DATA1_P
The positive DVI output number 1
O
11
GND
12
NC
Not connected
13
NC
Not connected
14
+5V
PWR
15
GND
PWR
16
HOTPLUG_DETECT
DVI Hot Plug signal
I
17
TMDS_DATA0_N
The negative DVI output number 0
O
Pull-up/Pull-down
PWR
+5V
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 18
Iris Carrier Board Datasheet
Pin
Signal Name
Description
18
TMDS_DATA0_P
The positive DVI output number 0
19
GND
20
NC
Not connected
21
NC
Not connected
22
GND
23
TMDS_CLK_P
The positive DVI Clock signal
O
24
TMDS_CLK_N
The negative DVI Clock signal
O
C1
CRT_RED
O
C2
CRT_GREEN
O
C3
CRT_BLUE
O
C4
CRT_HSYNC
O
C5
AGND
3.7.4
I/O Type
Voltage
Pull-up/Pull-down
I/O Type
Voltage
Pull-up/Pull-down
O
PWR
PWR
PWR
LVDS Connector (X7)
Connector type: Hirose DF13A-20DP-1.25V(56)
Pin
Signal Name
Description
1
LVDS_5V
5V power supply pin
PWR
+5V
2
LVDS_3.3V
3.3V power supply pin
PWR
+3.3V
3
GND
4
SEL1
Connected to LVDS_3.3V or GND via
assembly option. The default assembly is
GND
5
LVDS_OUT0_N
The negative LVDS output number 0
6
GND
7
LVDS_OUT0_P
The positive LVDS output number 0
O
8
LVDS_OUT1_N
The negative LVDS output number 1
O
9
GND
10
LVDS_OUT1_P
The positive LVDS output number 1
11
LVDS_OUT2_N
The negative LVDS output number 2
PWR
O
PWR
PWR
O
O
PWR
12
GND
13
LVDS_OUT2_P
The positive LVDS output number 2
O
14
LVDS_CLK_N
The negative LVDS clock signal
O
15
GND
16
LVDS_CLK_P
The positive LVDS clock signal
O
17
BL_ON
Back Light control signal
O
18
GND
19
SEL2
Connected to LVDS_5V, LVDS_3.3V or
GND via assembly option. The default
assembly is 5V
20
SEL3
Connected to LVDS_3.3V or GND via
assembly option. The default assembly is
LVDS_3.3V
PWR
PWR
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 19
Iris Carrier Board Datasheet
The following table describes the assembly options available on the Iris carrier board with respect to
the LVDS Interface:
Solution Selected
Assembly Options
Assembled
Components
on Iris V1.1
PCB Side
SEL1 Configuration
Assemble appropriate 0R resistor - R40 or R44.
R44
Top
SEL2 Configuration
Assemble appropriate 0R resistor - R37 or 41 or R45.
R37
Top
SEL3 Configuration
Assemble appropriate 0R resistor - R42 or R46.
R42
Top
Please refer to figure 4 in Section 2.4, Assembly Options for the position of the resistors.
Note:

Please use the pins 1 and 2 as power supply pins (max 0.9A) and the SEL1, SEL2, SEL3
as setting pins.
3.8. Audio Interface
3.8.1
Audio Jack (X8)
Connector type: CUI SJ-43516-SMT
Pin
Signal Name
1
Audio AGND
2
Headphone L
15
O
3
Headphone R
17
O
4
Not connected
5
Headphone L
15
O
6
Headphone R
17
O
3.8.2
SODIMM Pin Number
I/O Type
Voltage
Pull-up/Pull-down
I/O Type
Voltage
Pull-up/Pull-down
PWR
+3.3V
PWR
Audio Header (X9)
Connector type: 1x5 Pin Header Male, 2.54mm
Pin
Signal Name
SODIMM Pin Number
1
Audio AVCC
2
Microphone In
1
I
3
Line-In R
7
I
4
Line-In L
5
I
5
Audio AGND
PWR
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 20
Iris Carrier Board Datasheet
3.9. Digital and Analog I/O Interface
3.9.1
UART-A RS-232 header (X13)
The Full Function (FF) UART-A RS-232 connector is a 10 way (2 rows x 5 way) 2.54mm pitch header
capable of being connected to an industry standard DTK/INTEL 10 way IDC to 9 way D-type male
connector.
Connector type: 2x5 Pin Header Male, 2.54mm
Pin
Signal Name
1
RS232_A_ DCD
I
2
RS232_A_ DSR
I
3
RS232_A_ RXD
I
4
RS232_A_ RTS
O
5
RS232_A_ TXD
O
6
RS232_A_ CTS
I
7
RS232_A_ DTR
O
8
RS232_A_ RI
I
9
GND
10
NC
3.9.2
SODIMM Pin Number
I/O Type
Voltage
Pull-up/Pull-down
Voltage
Pull-up/Pull-down
PWR
UART-B/C RS-232 header (X14)
Connector type: 2x5 Pin Header Male, 2.54mm
Pin
Signal Name
SODIMM Pin Number
I/O Type
1
RS232_C_RXD
2
NC
3
RS232_B_RXD
I
4
RS232_B_RTS
O
5
RS232_B_TXD
O
6
RS232_B_CTS
I
7
RS232_C_TXD
O
8
NC
9
GND
10
NC
I
PWR
Remarks:

The RS232 serial transceivers can be shut down via two GPIOs which have been
connected to the ForceOFF# pin. This is needed in order to use the UART signals that are
on the extension connector at TTL logic level. The following table shows the SODIMM pin
assignment of the GPIOs reserved for this purpose:
Header
Signal Level  Header Status
Signal Level  Header Status
102
X13
Logic Low  Disabled
Logic High  Enabled
104
X14
Logic Low  Disabled
Logic High  Enabled
SODIMM Pin Number
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 21
Iris Carrier Board Datasheet
3.9.3
Extension Connector (X16)
Connector type: 2x20 Pin Header Male, 2.54mm
Pin
Signal Name
SODIMM Pin Number
I/O Type
Voltage
Pull-up/Pull-down
1
RESET_EXT#
26
I
+3.3V
2
GND
PWR
3
GND
PWR
4
RESET_OUT#
87
O
+3.3V
5
I2C_SDA
194
I/O
+3.3V
4.7K to 3.3V
6
12C_SCL
196
I/O
+3.3V
4.7K to 3.3V
7
GND
8
SSPSCLK
88
I/O
+3.3V
9
SSPFRM
86
I/O
+3.3V
10
SSPRXD
90
I
+3.3V
11
SSPTXD
92
O
+3.3V
12
+5V
PWR
+5V
13
SODIMM_98 (GPIO)
98
I/O
+3.3V
14
SODIMM_133 (GPIO)
133
I/O
+3.3V
15
SODIMM_103 (GPIO)
103
I/O
+3.3V
16
SODIMM_101 (GPIO)
101
I/O
+3.3V
17
SODIMM_97 (GPIO)
97
I/O
+3.3V
18
SODIMM_85 (GPIO)
85
I/O
+3.3V
19
SODIMM_79 (GPIO)
79
I/O
+3.3V
20
SODIMM_45 (GPIO)
45
I/O
+3.3V
21
GND
22
ANALOG_IN3
PWR
PWR
2
I
+3.3V
(Refer Note 1)
23
ANALOG_IN2
4
I
+3.3V
24
ANALOG_IN1
6
I
+3.3V
25
ANALOG_IN0
8
I
+3.3V
26
AUDIO_AGND
27
UART_A_ TXD
35
O
+3.3V
28
UART_A_ RXD
33
I
+3.3V
29
UART_B_ CTS
32
I
+3.3V
30
UART_B_ RTS
34
O
+3.3V
31
UART_B_ RXD
36
I
+3.3V
32
UART_B_ TXD
38
33
+3.3V
34
UART_C_ RXD
35
UART_C_ TXD
36
GND
37
PWM_A (Refer Note 2)
59
O
+3.3V
38
PWM_B
28
O
+3.3V
39
PWM_C
30
O
+3.3V
40
PWM_D (Refer Note 3)
67
O
+3.3V
PWR
O
+3.3V
PWR
+3.3V
19
I
+3.3V
21
O
+3.3V
PWR
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 22
Iris Carrier Board Datasheet
The following table describes the assembly options available on the Iris carrier board with respect to
the Analog-In Interface:
Solution Selected
Assembly Options
ANALOG_IN3
Disassemble the resistor R88
PWM_D for PXA3XX
modules
Assemble the resistor R110
Assembled
Components
on Iris V1.1
PCB Side
R88
Top
Bottom
Note 1:

The signal ANALOG_IN3 is also used as the TOUCH_WIPER signal for the Touch (X19) and
the RGB connector (X3). For this reason a populated 0ohm resistor (R88) has been placed
between the signals ANALOG_IN3 and TOUCH_WIPER. This resistor can be removed in the
event the fourth analog signal is required and the TOUCH_WIPER signal (for 5 wire resistive
touch screen panels) is not.
Note 2:

The PWM_A signal has also been routed to the RGB display connector (X3) to provide
backlight brightness control for connected LCD displays; for this reason a populated zero ohm
resistor (R84) has been placed before connector X16.
Note 3:

Since the Colibri PXA3XX does not support the PWM_D signal, pin 152 of the SODIMM
connector has been connected to the PWM_D line through a not assembled 0ohm resistor
(R110).
Please refer to figure 4 and 5 in Section 2.4, Assembly Options for the position of the resistors.
3.9.4
Touch Connector (X19)
Connector type: Hirose DF13C-6P-1.25V(51)
Pin Signal Name
SODIMM Pin Number
I/O Type
Voltage
1
GND
2
TOUCH_TSMY
20
I
+3.3V
3
TOUCH_TSPY
18
I
+3.3V
4
TOUCH_TSMX
16
I
+3.3V
5
TOUCH_TSPX
14
I
+3.3V
6
TOUCH_WIPER
2
I
+3.3V
Remarks
PWR
Shared with ANALOG_IN3,
(Refer Note 1)
Remarks:

For further information about the 5-wire resistive touch interface, please refer to our
developer site:
http://developer.toradex.com/knowledge-base/5-wire-resistive-touch-interface
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 23
Iris Carrier Board Datasheet
3.10. Real-Time Clock (RTC)
3.10.1 External RTC
The Iris carrier board uses the STMicroelectronics, M41T0M6 chip as external RTC.
3.10.2 Battery Holder (BAT1)
A 12 mm (diameter) coin cell/battery should be used with the Battery Holder (BAT1). Coin cell can be
used to provide power backup to the external RTC circuits when external power supply is not
available. The following type of batteries is supported: BR1216, CR1216, BR1220, CL1220, CR1220,
BR1225.
Connector type: KEYSTONE-3000
Pin
Description
1
VCC_BAT
2
GND
Voltage
+3.0V
Note:
The spring contact on the top side of the battery holder sets/bends based on the battery thickness.
In case a thicker battery (like BR1225, 2.5mm thickness) is inserted first, the spring contact will set
and later if the battery is replaced by a thinner battery (like BR1220, 2.0mm thickness). The battery
holder will not hold the replacement battery firmly.
Customers are advised to not to use thinner battery after using the thicker battery with the battery
holder (BAT1).
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 24
Iris Carrier Board Datasheet
4. Electrical Characteristics
4.1. Electrical Specifications
Symbol
Description
PWR_IN_V
Main power supply voltage
PWR_IN_I
Main power supply current
V_BACKUP
Optional RTC battery voltage
I_(+5V)
Total current for external devices at power rail:
Voltage
Min
Typ
Max
Unit
6
24
27
V
6
A
3
3.6
V
+5V
2.5
A
1.5
A
0
2.3
X16 Pin 12
X20 Pin 1
USB connectors / USB header
I_(+3.3V)
Total current for external devices at power rail:
X16 Pin 33
X20 Pin 3
+3.3V
I_Pin(X16)
Current for the single power pin 33 of connector X16
+3.3V
0.5
1.5
A
I_Pin(X20)
Current for the single power pin 3 of connector X20
+3.3V
1.0
1.5
A
I_Pin(X11)
Current for a single power pin of connector X11
+5V
0.5
A
I_Pin(X12)
Current for a single power pin of connector X12
+5V
0.5
A
I_Pin(X16)
Current for the single power pin 12 of connector X16
+5V
1.0
2.5
A
I_Pin(X20)
Current for the single power pin 1 of connector X20
+5V
1.0
2.5
A
5. Temperature Range
5.1. Operating Temperature Range


- 10 to 70 °C
- 20 to 85 °C (the LVDS picture quality might be lower at this range)]
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 25
Iris Carrier Board Datasheet
6. Mechanical Data
6.1. Iris Dimensions – Top Side
Fig.7 Iris Dimensions – Top Side, all dimensions are in millimetres (mm)
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 26
Iris Carrier Board Datasheet
6.2. Iris Dimensions – Bottom Side
Fig.7 Iris Dimensions – Bottom Side, all dimensions are in millimetres (mm)
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 27
Iris Carrier Board Datasheet
7. Design Data
The design data for Toradex carrier boards are freely available in the Altium Designer format. The
design data includes schematics, layout, and component libraries.
To download the carrier board design data, please use the web-link below:
http://developer.toradex.com/carrier-board-design
8. Product Compliance
Up-to-date information about product compliance such as RoHS, CE, UL-94, Conflict Mineral, REACH
etc. can be found on our website at: http://www.toradex.com/support/product-compliance
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 28
Iris Carrier Board Datasheet
Disclaimer:
Copyright © Toradex AG. All rights reserved. All data is for information purposes only and not
guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate;
however, no responsibility is assumed for inaccuracies.
Brand and product names are trademarks or registered trademarks of their respective owners.
Specifications are subject to change without notice.
Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l [email protected]
Page | 29
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement