rauland 2524 ChronoCom Programming Manual

PDF

Documento

KI-1

629

ChronoCom TM Master Clock and

Intercom Controller

Programming

RAULAND-BORG CORPORATION

3450 West Oakton Street, Skokie, Illinois

60076-2951 l

(708) 679-0900

General Information

2

Description

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Programming Summary 2

Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Access to Programming

General Methods

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Exiting.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Planning

3

Planning Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Zones Chart..........:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Clock Modes A-F 5

Mode D (Edit Holiday events) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mode E (Relay Panels,Comm Activation) ..........................................................

Mode

F (Events: Totals and Erase All) ............................................................. .7

Clock

Modes

l-6 7

Mode 2 (Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mode 3 (Enter Regular Events) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Mode 4

(Edit Regular Events) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Mode 5 (Zone Duration)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mode 6 (Activate Zones and Schedules) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mode 0 (Run)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0

Communication Modes 1 0

Mode 2 (Zones and Scanning)...................................................................l 0

Printed in U.S.A.

Ruig.

4/90

Page

1 o f 17

2524

ChronoCom Programming

Mode 3 (System Options) . . . . . . . . . . . . . . . . . . .

TC4200 Display .........................

Automatically Connect Priority Call-ins .......

Remote Phone ...........................

Mode 4 (Monitoring Duration) . . . . . . . . . . . . . . .

Mode 5 (Call-in Sensitivity) ..................

ModeO(Run) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.......

. . . . . . .

. .

. . .

. .

. . .

. . . .

. . . . .

.......

....... 11

.......

Work Sheet for Custom Secondary-Clock Code

Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Commentary: ...........................

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 Programming Charts

14

General Information

Description

The Rauland 2524 is a multi-function Master Clock and

Communications Control Center. As a master clock, it will synchronize virtually any kind of secondary clock and control up to 350 “events” (such as sending tone signals or turning lights and equipment on and off). As an intercom controller, it adds control of room-switching functions and display functions to Director III intercom-control els.

anuals

This manual tells how to program the 2524 for both clock and intercom functions. The first section gives the basic programming procedures. The “Clock Modes A-F” section explains the programming for the general settings needed by the unit, whether it is used only as a master clock or also as a control unit for communications. The last two sections deal with the clock and intercom functions, respectively.

Generally, the Clock Modes A-E, especially Clock Mode

A, should be done before the numerical modes. Refer also to KI-1628, 2524 Installation, and KI-1630, 2524 Opera-

tfon.

Following the text are four tables that list all of the programming functions. Also attached are a work sheet for devising a special clock-correction code and charts for planning the system programming.

Power-up

When the 2524 is turned on, its displays normally appear as follows: the “Mode” window reads “0” (Run

Mode), the “Time” window shows the current time, the

“Sched” (“Schedule”) window shows a flashing “P” (to indicate that the power was off), and the “Clock” LED lights (to show the unit is set for clock operation). Push any key to stop the flashing “P.”

* The “Sched” window will show the number of the schedule currently in use.

Note: If the battery was “disabled,” the “Time” display may be random. In this case, set the date and time (Clock

Modes 1 and 2).

Programming Summary

This section gives the procedures for accessing, changing, and entering programming information.

After this summary, there is a section on planning. Then the three groups of programming modes are explained.

The alphabetical modes (A-F) are explained first, because this group affects both clock and intercom operation; moreover, these settings arc usually entered during setup and left that way, except for the annual holiday and

Daylight Savings Time changes. The other clock and the intercom modes follow in that order.

Sequence

P

Important:

Before entering clock events (Clock Mode editing them (Clock Mode 4), you should enter any c ock-correction codes (Mode A), because each code takes up two outputs that arc not, consequently, available for events. The 2524 will not allow you to enter an event for a zone that is taken up by a clock code. Should you enter events for zones that you subsequently take up with a clock code, the 2524 will not erase them. However, it will not activate events in clock-code tones, and these zones’

LEDs will not light when you review the events in Clock

Mode 4. The remaining modes may be programmed in any order.

Access to Programming

To begin programming, the clock must be in the Clock

Run Mode (“0”).

Step 1. Enter the Security Code (Funct 2524-that is, press in succession the Funct, 2, 5 , 2, and 4 keys):

Page 2 4/90

* The “0” in the “Mode” window will flash, meaning that you can select a programming mode. If you pause more than five seconds between keystrokes or enter invalid keystrokes, the clock will display

“ErrO,”

“beep,” and, after a moment, revert to the

Clock Run Mode.

Step 2. To select the Clock Modes, skip to Step 3. To

select the “Comm” modes, push the white Clock/Comm button.

* The “Comm” LED will light steadily, a “1” will flash in the “Mode” window, and a “P” will appear in the

“Sched” window.

Note: Once you select intercom programming, you can only select those “Comm” modes. To select the clock modes, you have to Erst exit to the Clock Run Mode, then begin again with Step 1.

Step 3. To select a numbered mode (l-9, type in its

number; to select a letter mode, press Funct while you type the corresponding number (“1” for “A,” “2” for “B,” etc.).

* The number or letter you selected will show steady in the “Mode” window. You can now either enter a different mode or commence programming.

General

Methods

Flashing, whether in a window or an entire group of

LEDs, marks the spot (field) in the programming that will be affected by your entrles. We refer to this flashing area as the “flashing cursor.”

Planning

2524 ChronoCom Programming

Step 1. When you are in

the desired mode,

USC t h e cursor keys (+ and -*) to move to the desired window or

LED group.

Step 2. Use the digit keys to enter the desired program-

ming. Keys 1-8 toggle the individual “Zones” and “Days”

LEDs on and off.

Step 3. Use the orange Clear key to restore a field’s

previous setting (except in Mode B, where it is used to enter the entire series of numbers). When you are sure all the entries for the mode (or individual event) are correct, press the orange Enter key.

* The new programming will be stored in the clock’s memory, and the “Time” window and any involved

LEDs will light steady, to show your final entries. If you enter invalid data, such as “13” for the month, the 2524 will “beep” and flash the left-most field that had an error (for times and dates, the 2524 typically reverts to the last valid entry). Correct that field and press Enter, which will cause the 2524 to record this change and check for any other errors. If it finds one, it will flash that field.

Note: In Modes 1 and 2, the 2524 will automatically advance to the next mode after you press Enter.

Exiting

To quit programming, return the cursor to the “Mode” window and type a “0” (Clock Run Mode). Alternatively, do nothing for one minute. In either case, the 2524 will return to the Clock Run Mode.

Information Needed

Because

of the interrelation between the wiring and the programming, a good deal of programming-related planning was required for the installation. You need the following information from that planning:

4 What is connected to each “Zone/Output” terminal

(secondary clocks, equipment, etc.).

4 What, if

any, secondary clock codes are needed; if two are used, which is needed for Outputs

and which for Outputs 7 and 8.

5

and 6,

4 How many relay panels are connected (O-20).

Whether there is an audio program source that can be used for clock events (“Music”).

v’

Whether there is a tone generator for clock tones.

From the customer, you need to find out:

The desired schedules for clock events, including lected stations, so that the operator can listen for any unusual sound that signals a need for action.)

Most of this information can simply be entered in one or two steps and, accordingly, will be explained in the appropriate “Modes” section of this manual. The events and the paging zones require more planning.

Planning Charts

Completing the charts attached to the end of this manual is an important part of planning. This will help you organize the programming, make it easier to enter the data, give the user helpful information, and simplify later programming changes. When you are Finished, provide copies to the users and keep a set for your own files.

holidays.

The desired zones for clock events and intercom paging.

The dates of the holidays and other special days for which a special schedule is desired. (You also need to know the dates for the changes to and from

Daylight Savings Time.)

The calling (“Architectural”) number that should be

Zones

Chart

When the 2524 is wired and used like a conventional master clock, you can easily figure out how its zones can be used. Any output connected to secondary clocks or to equipment can serve only them.

However, wiring the 2524 to speakers via relay panels introduces a second type of zone, which is determined by the software in “Comm” Mode 2. Although these two types of zones work independently in some respects, they programmed for each room station (typically the same as the room number).

are closely interrelated:

Which rooms should be included in the monitoring

These

software

zones are used for both events and function. (When this function is activated by the paging; thus, a page sent to Zone 4 will

include the operator, it continuously cycles through the se- same speakers as a clock-tone event.

4/90 Page 3

2524 ChronoCom Programming

The eight zones are tied in with the 2524’s

“Zone/Output” terminals. For example, if

Outputs

and 8 are used for a clock-correction code, you

cannot use Zones 7 and 8 for events (e.g., for sending clock tones via speakers).

To have clock tones via speakers, the corresponding output terminals must be wired to the tone generator, in or&r to activate the tone signals. This eliminates the use of clock events via speakers in any zone whose corresponding output terminal is used for correcting clocks or controlling equipment.

It is possible to have paging zones when the corresponding outputs are used for clock-correction codes. However, since the output terminals are tied up, they cannot channel tones or music to the speaker zones.

All

of these factors are summarized in the following table. Note that only one of the listed combinations can be active in a zone at a time. The first four zones have only two choice because clock-correction codes can only use

Outputs 5-8.

--.

Assigning Functions to Zones

Zone Possible Functions

1 T&P or L.

2 T&P or L.

3

T&P or L.

T&P or L or C&P

T = clock Tones via speakers.

P = Paging zones.

L = Latching zone for controlling equipment.

C = Clock-correction signal.

The “Duration” (Clock

Mode 5) tells how long an event will continue: l-59 seconds for tones, or “00” for latched events (an event with “00” duration holds the affected zone’s relay closed until another event, which does not include that zone, is executed). The “Description” is for the programmer and user. For example, a zone could be described as an area (“West Wing”), a classification (laboratory classes), a time (evenings, week-ends), or a function

(outside lights).

Stations Chart

This is needed only when relay panels are controlled by the 2524. Although the chart primarily deals with intercom functions, the “Paging Zones” entry directly affects clock tones sent to the speakers.

Physical Number: This refers to specific terminals on relay switching panels. The first terminal on the first nel is “001,” the first terminal on the second panel is

“026,” and so on. The system uses these numbers to keep track of each station (e.g., to determine which station is

J calling in, or to determine which relay to close to connect the operator with a station). The only way to change a station’s Physical Number is to wire it to different terminals.

Architectural Number: This is the number the user will enter on the 2524’s keypad in order to call the room.

The 2524 locks up the corresponding Physical Number to carry out the desired communications function.

Users typically want the room number for calling, but any three-digit number can be used. Make sure that you do not assign the same number to more than one station.

Paging Zones: Each room can be assigned no zones or from one to eight zones in any combination. Assigning a zone to a station means that the latter will receive both paging and clock events for that zone.

Monitor: Giving a station this feature means that

it will be included when the 2524’s monitoring function is enabled (see also “Comm” Modes in the “Comm” Run Mode, the monitoring function momentarily connects the control panel to each selected station in succession, so that the user can listen for disturbances or unusual sounds. The length of time that the

2524 remains connected to each station is determined by

“Comm” Mode 4.

Supervision: This setting determines whether or not a station will be included when the 2524’s supervisory function is activated. This function scans the selected stations for wiring faults. When activated in “Comm”

Mode

3,

3

and 4). When activated the function automatically runs every hour; it can also be manually activated at any time.

The Events Chart

This chart contains the most columns and will typically have the largest number of entries. In order to fill it out, you first have to fill out the charts explained above.

An “event” is simply the automatic closing of a “Zone” output terminal and the pulling in of relays on optional speaker relay panels.

The circuit closure on an output, in turn, is used to control external devices connected to the clock. The output may activate for a programmed time between one and 59 seconds (to ring bells, for instance), or it may be left on until it is turned off again by another event at a different time (to control lights or heating equipment, for instance).

The pulling in of panel relays enables clock tones or an audio program to be sent to room speakers.

Entering an event requires five pieces of information: the time and the days when the event will take place, which “Zone” outputs will be activated, which schedule is involved, and, if music or other audio programming is desired, how long it should play.

‘Event No.“: This column is for your reference only- to

keep track of the number of events, etc.; it is not programmed into the clock.

Time: If you are using the 12-hour display-format, be

sure to indicate “AM" and “PM”; if you are using the

24-hour format, leave the “AM” and “PM” columns blank

but use “13"-"23” for

the “PM” hours. Use this chart for

your own and the user’s convenience: should you quently change modes, the times for the

subse-

the clock will automatically adjust

events. Thus, if you

are more familiar

Page 4

4/90

2524 ChronoCom Programming

Mode B (Custom Clock Code)

This mode is used to program a correction routine for

a secondary clock that does not match any of the 2524’s standard codes. You can enter up to two sets of seven integers. The first set consists of Integers “01” through

“07,” and the second set consists of Integers “08” through

“14.” an invalid code entry, it will “beep” and keep the cursor on the “Time” window.

Creating a Custom Code

Find out the precise correction requirements of your special secondary clock. This includes such items as the on and off times for correcting the time, whether there is more than one clock motor involved, and the output or outputs on the 2524 to which the clock is wired.78 Use the

“Custom Code Work Sheet” at the back of this manual to establish the 2524 programming for the clock. After entering this programming into the 2524, keep this work sheet with the other installation documents for future reference.

Entering the Custom Code

Step 1. After entering the clock programming modes, select Mode B by holding in

Funct while you

press 2.

* A “b” will appear in the “Mode” window, and the left

“Time” window will display “01,” which indicates that the number in the right window is the first integer for the custom code.

Step 2. Push + to move the flashing cursor into the ht “Tie” window.

’

* The two digits in that window will flash.

Step 3. Type in the first two-digit number from your work sheet, then push

Enter.

* The left

“Time” window will increment to the next number, and the right window will flash the current entry for that integer.

Note: For Integers that need to be designated as minutes or

seconds (bytes

4, 6, 11, and 13), push

Funct to

toggle between minutes and seconds (the “PM” LED lights for “minutes’). When the setting is satisfactory, press

Enter.

Step 4. When you have finished with this mode, push

Clear to enter your code into the EEPROM.

=r All the custom-code settings will be entered, and the

“Time” windows will show the first integer.

Step 5. Go to Mode A and enter “21” as one of the correction codes. Be sure to select it as the first or second code in accordance with your work sheet.

Mode C (Holidays and Time Changes)

This mode is used to enter the dates for the holidays and Daylight Savings time changes.

Step 1. After entering the clock programming

modes

or finishing in another mode, select this mode by holding in

Funct

while you press3.

* A “C” will appear in the “Mode” window.

Step 2. Press --, to move the “flashing cursor” to the

"Time” windows.

* The “Time” windows will flash.

Step 3. To select a day for a special schedule

an automatic timechange, type two digits for the month and two more for the date (MMDD). Press * to move the cursor to the “Sched” window.

e The “Time” windows will go steady and the “Sched” window will flash.

Step 4. Make one of the following entries:

To disable all events on tbat day:

Type “0.”

To select a special schedule for tbat day:

Type in the on this date.

To repeat a holiday schedule on consecutive days:

you enter a schedule number, as explained in the preceding paragraph, the Schedule window will go steady and the “Music” LED will flash. If you want the holiday schedule you just entered to run for more than one day, type ” 1.” The left “Time” display will show

“du” (“duration”). Type in an integer (from 1 to 15) to

specify

iday schedule to run. This option is useful for vacation periods.

To advance tbe time one bour at

1 to enter "A” (“Advance”) in the “Sched” window.

To turn back the time one hour at 2 a. m.

6

Step 5. When you are satisfied with your entries, press

Enter.

holiday-and time-change events entered in Mode C.

select Mode D by simultaneously holding in you press 4.

3.

schedule’s number (1 through 8). Whether or not the schedule is selected in Mode 6, it will automatically run

This

how many consecutive days you want this holto enter “F” (“Fall” or “fall back”) in the “Sched” window.

a.m.:

Press

Funct

and

Mode D (Edit Holiday events)

Press

Funct

and

* The 2524

will check your entry for a valid date; if it finds an error, it will flash your entry in the “Time” windows. If you entered a “duration” value (to repeat a holiday schedule), the program will check it for validity, too. If it finds an error, it will “beep” to

Indicate an error, continue displaying “du” in the left

“Time” window, and flash the right “Time” window.

If you did not enter a duration value or if the program does not End any errors, it will store this holiday event and flash the “Time” windows again, signaling that it is ready for another entry.

mode is used to review, edit, and delete the

Step 1. After entering the clock programming modes,

* The “Mode” window will show a “d,” and the remaining windows and LEDs (except “Clock” and

“Comm”) will display the first holiday (in chronological order).

Step 2. If you want to work with this event, skip to Step

To move to the next holiday, push the

Funct

Enter

After while key. T

O move directly to an event for a certain date, press + to move the cursor into the “Time” windows, enter the desired date in the “MMDD” format, and push

* The

Funct.

front-pane1 displays will show the selected holiday event. If no holiday event has been programed on the selected date, the 2524 will display the event

Page 6

4/90

for the earliest following date. if there is no later holiday event, the 2524 will “beep” and display its earliest holiday event; if no holidays are programmed, the 2524 will “beep” and flash the “Mode” window.

Step 3. To modify an event, use the cursor keys to

select the appropriate window or LED block, then enter

the desired number. To delete an event, move the flashing

cursor into the “Time” windows, then press Erase. Check

your entries, then press Enter.

.* The 2524 will enter any changes into the EEPROM

(or erase an event from there) and display the next event.

Step 4. When you are finished programming in this mode, move the flashing cursor to the “Mode” window and select another programming mode or enter “0” to return the 2524 to the Clock Run Mode.

Mode E (Relay Panels, Comm Activation)

This

mode has three settings. The first tells the 2524 how many “SC” relay panels (TC4110, TC4130, or

TC4131) are connected

to it. The second tells the 2524 whether or not it should activate its communication functions. Unless this operating mode is activated here, the

2524 will not receive call-ins, make calls, do paging, or even switch over to the “Comm” mode. The third setting determines whether or not the 2524 will handle call-ins.

Important: Be sure to enter the correct number of relay panels. If, for example, you specified “20” but there were only two, the 2524 would operate correctly but more slowly, because it would waste time trying to work with non-existent relay panels: checking them for call-ins, trying to pull them in for paging, etc. On the other hand, if you were to specify fewer relay panels than there actually are, the 2524 would ignore call-ins from the highernumbered panels, and you would not be able to call

rooms connected to them. If no relays are connected to

the 2524, leave the intercom function disabled (the factory setting) to prevent an operator from entering the

“Comm” Mode, which blanks out the clock information from the front panel.

Step 1. After entering the clock programming function,

hold in Funct while you press 5.

* The “Mode” window will flash “E,” the left “Time” window will display “SC,” the right “Time” window will show the previously programed number of relay panels, and the “Sched” window will show “0”

(“Off) if the call-in function has been disabled or

“C” if it is enabled.

Step 2. Push + to move the flashing cursor to the

“Time” windows.

* The right “Time” window will flash.

2524 ChronoCom Programming

Step 3. Enter any number between “00” and ”20,” then move the flashing cursor to the “Zones” LEDs.

* If the communications mode is enabled, the first

LED will flash at the approximate rate of one second on and one second off; the remaining LEDs in

this block

will remain off. If the “Comm” mode is disabled, all eight LEDs in the blockwill flash at the rate of a half-second on and one-and-a-half seconds off.

If the “Comm” mode has already been enabled, the first “Zone” LED will light steadily, and the other

LEDs will be off.

Step 4. Use the 1 key to toggle between the two settings. When the setting is satisfactory, press --+ to move the flashing cursor to the “Sched” window.

* The “Sched” window will flash.

Step 5. Push Funct to

toggle between “0” (“Off’) and

“C” (call-ins). Make sure that all three settings are satisfac-

tory, then push Enter to store the data.

Important: You must calibrate Pot

RP1 in “Comm”

Mode 5 before.activating the call-scanning function here.

* The stored settings will be displayed, and the

“Mode” window will flash.

Step 6. You can now specify another mode for programming or enter “0” to return the 2524 to the Clock

Run Mode.

Mode F

(Events: Totals and Erase All)

This mode will show how many regular events and how many holiday events have been programmed. It can be also used to erase all of these events.

Step 1. If necessary, enter the clock programming

mode. Hold in Funct while you type a 6.

» The “Mode” window will flash “F,” the “Time” windows will display the number of events, and the

“Sched” window will show an “E” (regular Events).

Step 2. Use the Enter key to toggle between the regular

events and the holiday events.

» For the holiday events, the “Time” windows will display the appropriate number, and the “Sched” window will show “H.”

Step 3. To simultaneously delete all events (both regular and holiday), move the flashing cursor to the “Time”

windows, push and release the Funct key, type “2524,”

then press Enter.

Note: It does not matter which kind of events is cur-

rently displayed, since this procedure will erase both kinds at the same time.

» The “Mode” window will flash “F,” and the “Time” windows will show “0000,” indicating that no events are stored.

Step 4. You can now proceed to another mode or exit the programming function.

Clock Modes

1-6

Before beginning here, you should fill out the programming charts, as explained in the “Planning” section of this manual. You should also have completed the programming Modes A-F, espcially Mode A.

Mode 1 (Date)

Step 1. If necessary, enter the clock programming function. If you are

in a different programming mode,

press 1 while the “Mode”

window is flashing.

Page 7

2524 ChronoCom Programming

» A “1” will flash in the “Mode” window, and the

“Time” windows will show the current setting for the year.

Step

Press + to flash the “Time” windows. To ange the year, type in any number from

“2099.” Check the entry, then press Enter.

"1989"

» If you typed an invalid date, the 2524 will “beep,” redisplay its current setting, and wait for you to repeat this step. Otherwise, the 2524 will store your new date and flash its current setting for the month in the left “Time” window and that for the day in the right “Time” window (e.g., “03 15”).

Step 3. To change the date, type two digits for the month and two more for the day’s date (e.g., “03” for

“March” and “15” for the day. Make sure that your entry is satisfactory, then store it by pressing Enter.

» If you typed an invalid date, the 2524 will “beep,” redisplay its current date setting, and wait for you to repeat this step. If your date is valid, the 2524 will store it and Dash a “2” in the “Mode” window, indicating that the unit has automatically advanced to the next mode.

Mode

2 (Time)

Step

is flashing.

If necessary, press 2 while the “Mode” window

» A “2” will flash in the “Mode” window, and the

“Time” windows will show the current time setting.

Step

2. Push +.

» The “Time” windows will flash.

Step 3. To change to the 12- or 24-hour format, hold e Funct key while you press one of the following:

For the 24hour mode, press 2.

» The “AM” or “PM” LED will light if you selected the

12-hour mode, or turn off if you switched to the

24-hour mode. If an afternoon-time is set in the clock, the numbers will change (e.g., between

“03:27” pm and “15:27"). The “Time” windows will continue flashing.

Step 4. Enter four digits for the time (e.g., “0305” for

“3:05”). Your entry must match the 12- or 24-hour time mode (e.g., the 2524 will not accept “20:50” for “8:50 p.m.“).

» If the 2524 is in the 12-hour mode, the “Time” windows will go steady and the “AM” or “PM” LED will flash. If the 2524 is in the 24-hour mode, the

“Time” windows will continue to flash after you have typed in the new numbers.

Step 5. If you are in the 24-hour mode, skip to Step 6.

Press 1 to change to AM, or 2 to change to PM.

Step 6. When you are satisfied with the settings, press

Enter.

* An invalid time will cause the 2524 to “beep,” flash its current setting in the “Time” windows, and wait for you to enter a valid time. A valid entry will cause the 2524 to enter the new time and automatically m.

switch to Mode 3.

Step 7. Continue with Mode 3. enter the number of a cnt mode, or enter ”O” to return the 2524 to the Run

Mode 3 (Enter Regular Events)

This

mode is used to load new events (ringing bells, turning equipment on or off, etc.). You will need to write out all the events first, using copies of the attached Events

Chart, to use as guides.

Step 1. If necessary, get the “Mode” window to flash by entering the programming function or moving out of another programming mode.

Step 2. Type a “3”.

* The “Mode” window will flash the

“3,”

the “Time” windows will show the current time, all the valid

“Zones” LEDs and the “Days” LEDs will light, the

“Sched” window will show “ 1,” and the “Music” LED will be off.

Step 3. Push + to move the flashing cursor into the

“Time” windows.

* The “Time” windows will flash.

Step 4. Type in the time, using four digits.

* The new time will appear in the “Time” windows. If the 2524 is in the 24-hour mode, ail the available

“Zones” LEDs will flash, so you can skip to Step 6. If the 2524 is in the 12-hour mode, the “‘AM” or “PM”

LED will flash.

Step 5. Press 1 to select “‘AM” or 2 to select “PM.”

Alternatively, if the desired LED is flashing, you can press

+ to move to the next field.

* The selected LED will light steadily and all the available “Zone” LEDs will flash.

Step 6. Select the desired zones by using the corresponding keys. For example, pressing

Zone

3

LED on and off. When only the desired LEDs are lit, press + to move to the “Days” LEDs.

3

will toggle the

* The “Zone” LEDs you selected will light steadily, and all the “Days” LEDs will flash.

Note on the Flashing of LEDs: In this mode, when the

“cursor” is on the “Zones,” “Days,” or “Music” LEDs, the

2524 provides two types of flashing. If at least one LED in the field is selected, the 2524 will flash it at the rate of a half-second on and a half-second off. However, if no LED in that field is selected, the 2524 will flash the entire field at the rate of a half-second on and one-and-a-half seconds off. This enables you to quickly detect when the entire

LED block is off or on.

Step 7. Select the desired days by using the corresponding keys. For example, pressing 4 will toggle the

“Th” LED on and off. When only the desired LEDs are lit, press -B to

move

to the “Schcd” window.

* The selected “Days” LEDs will light steadily, and the

“Schcd” window will flash.

Step 8. Enter one schedule number (“1” through “8”).

* The number will be shown steadily in the “Sched” window, and the “Music” LED will flash.

Step 9. lf you want music to play over the speakers after they have sounded the bell tone, type in a “1 ." If you do not want this music, type in a

“0."

If you did not select music ("0”), the “Music” LED will flash at the rate of a half-second on and one-anda-half seconds off. If you selected music (“I”), the

“Music” LED will glow steadily, the left “Time” win-

Page 8 4/90

dow will read “du” (“duration”), and the right

“Time” window will flash.

Step 10. If you did not select music, skip to Step 11. If you did select music, type in a two-digit number to indicate how long you want the music to play. You can specify from one to 15 minutes (“01” through "15”).

* The right “Time” window will flash the number you entered.

Step 11. Check all the settings for the event. When all

is satisfactory, push

Enter.

* The 2524 will

check all the settings for this event. If it finds an invalid setting, it will “beep” and flash that setting; if there is more than one error, the 2524 will flash the left-most one, and work its way to the right as you correct each error. If no errors are found the

2524 will store the event and flash the “Time” window to show it is ready for you to enter another event (the time shown will be that which you entered for the last event).

Note: To

change any setting, use the cursor keys in the usual way to move back and forth through the settings.

The one exception is when the cursor is “Time” windows for the “du” setting: in this case, press the left (c) cursor to move the flashing cursor back to the “Sched” window

(or further back). To change the “du” setting when you have just entered an undesired value, push t, to return to the “Sched” window, push -, to move back to the

“Music” LED, then push 1 to select music again.

Step 12. When you are finished with this mode, move the flashing cursor back to the “Mode” window and either select another programming mode or type in “0” to

return

the

2524

to the Clock Run Mode.

Mode 4

(Edit Regular Events)

This

mode is used to Review, Edit, and Delete regular events.

Step 1. If necessary, get the “Mode” window to flash by entering the clock-programming function or moving out of another of its modes.

Step 2. Type a “4.”

* The “Mode” window will flash the “4,” the “Time” window will show the earliest time of day programmed for an event, and the LEDs and windows will show the programming for this event.

Step

3. To move to tbe next event,

push the

Enter

key.

To move to a specificevent,

push the --* key once to move the flashing cursor into the “Time” windows, enter the time of the event there, then press

Funct.

Caution:

Do not press

Enter, because

that would enter a new time for the displayed event.

* The next or the selected event will be displayed, and the flashing cursor will move back to the “Mode” window. If you entered a time for which there is no event, the 2524 will display the earliest event following the time you entered. If there is no event at that time or later, the 2524 will “beep” and display the latest event.

Step 4.

To edit (change)

any part

of an event,

move the flashing cursor to the appropriate window or LED block. Enter changes by typing in the desired value or using the numerical keys to toggle the LEDs on and off, as in Mode 3. To access the “duration” window, you have to enter a “1” when the “Music” window is flashing. When

2524 ChronoCom Programming

the 2524 shows the event as you want it, push

Enter. To erase a displayed event,

move the flashing cursor into the

“Time” window and press

Erase.

* The

event will be reprogrammed or erased, and th4

2524 will display the next event and move the flashing cursor back to the “Mode” window.

Step 5. When you are finished with this mode, move

the flashing cursor back to the “Mode” window, if necessary, and either select another programming mode or type in “0” to return the 2524 to the Clock Run Mode.

Mode 5 (Zone Duration)

This

mode is used to program the length of time (duration) that each zone’s relaywill close when it is activated by an event. Two kinds of events are set up here: regular, short-duration events like sounding a bell tone, and latched events, which turn on a

relay and leave it on until

another event turns it off. Latched events are used for controlling such things as lights and equipment for heating and cooling. Note that the duration for music or other program material is set as part of the event itself in Mode3.

Step 1. If necessary, get the “Mode” window to flash by

entering the programming function or moving out of another programming mode.

Step 2. Type a “5.”

* The “Mode” window will flash the “5,” the “Zone 1”

LED will light, the left “Time” window will show “du”

(“duration”), and the right “Time” window will flash with the programed duration of Zone 1.

Step 3. To cycle through the zones, press

Enter

while the right “Time” window is flashing.

* Whenever you press

Enter,

the 2524 will advance in numerical order to the next zone; after Zone 8, it will wrap around to Zone 1. If a zone is used for a clock-correction code and is therefore not available for events, the “Time” windows will show “Corr.”

Step 4. For a regular duration, type in from ”0l” second

to “59” seconds; for a latched event, type in “00.” When the zone is the way you want it, press

Enter.

* The 2524 will

store the new duration, turn off the

LED for that zone, and display the duration for the next zone.

Step 5. When you are finished with this mode, move

the flashing cursor back to the “Mode” window and either select another clock-programming mode or type in “0” to return the 2524 to the Clock Run Mode.

Mode 6 (Activate Zones and Schedules)

This

mode determines which zones and schedules are active. Unless a zone is “turned on” in this mode, it will not run even though it is included in a regular event that the 2524 executes. For example, if a regular event included Zones 1-4 but only Zone

3

was activated in Mode

6, the 2524 would only carry out this event in Zone

3.

Only one schedule can be active at a time, and only those regular events that have the currently selected schedule will be executed.

Note: A holiday entry will execute the events in its selected schedule even if they have not been sclcctcd in

Mode 6.

Step 1. If necessary, get the “Mode” window to flash by

entering the clock-programming function or moving out of another of its modes.

4/90

Page

Step 2. Type a 6”.

* The “Mode” window will flash the

“6,”

the “Time” window will be blank, the LED of each active zone will be lit, and the “Sched” window will show the currently selected schedule.

Step 3. To select

a different schedule,

skip to Step 5.

To select

different zones,

move the flashing cursor to the

“Zones” block.

* The currently selected “Zones” LEDs will flash; if none is selected, the entire block will light for a half-second every two seconds.

Step 4. Use the corresponding numeric keys to toggle the “Zones” LEDs on and off.

* Each available zone’s LED will toggle on and off as you press its corresponding numeric key. If you press the numeric key for a zone being used for clock corrections, nothing will happen.

Step 5. To select a different schedule, press + to move the flashing cursor to the “Sched” window. Type in a number from “1” to “8.” Doublethcck both this value and the “Zone” LEDs, then push Enter.

* The

“Zone” LEDs and the “Sched” window will light steadily with your new entries, and the

“Mode” window will flash.

Step 6. Select another clock-programming mode or type in “0” to return the 2524 to the Clock Run Mode.

Mode 0 (Run)

The

Clock Run Mode is the normal operating state of the 2524. To enter this mode from any programming mode, type a “0” while the “Mode” window is flashing.

Note that the 2524 will automatically revert to the Clock

Run

Mode

from any programming mode after one minute of inactivity (no button is pushed).

Communication

Modes

Before beginning here, you should have filled out the progra mming charts, as explained in the “Planning” section of this manual. You should also have performed the clock programming modes, especially Mode A.

Entering the "Comm”

Modes

Step 1. Enter the programming function in the usual way, by typing in the security code (Funct 2524).

A “0” will flash in the “Mode” window.

Step 2. Press the

Clock/Comm

(upper right) key once.

* The “Comm” LED will light and the “Clock” LED will go out, indicating that the 2524 is in the intercom function. The “Mode” window will flash “1.”

Step 3. Enter the number of the desired “Comm” programming mode (other than “1”).

Note:

Once you have entered the “Comm” function, you can access only the “Comm” programming functions.

To program clock functions, you first have to return to the

“Run” Mode, which will automatically return the 2524 to the Clock Run Mode.

Mode 1 (Room Numbers)

This mode is used for entering the “Architectural Number” for each room that can be called. This is the number that the user “dials” on the 2524’s keypad when calling the room, and it is the number that appears in the “Time” windows when the r o o m calls in. We designate this number “Architectural” because many users find it convenient to assign the room number for this purpose.

The 2524 uses a set of “Physical Numbers” that correspond to the room wiring. In this programming, you assign an Architectural Number to each Physical Number that has an intercom speaker. The 2524 then refers to an internal table of Architectural and Physical Numbers so that it knows which relay to activate and which number to display.

Step 1. Enter the “Comm” programming function, as described above; if you arc already in this programming function, move the flashing cursor to the “Mode” window a

‘he “Mode” window will flash “1.” the “Station”

(“Time”) window will read “001,” and the “Sched” window will read “P” (“Physical”). This means that you are ready to program the lowest Physical Number.

Step 2. Press the right cursor key (4) once to move the flashing cursor into the “Station” window. If you want to check or change the Architectural Number for this station, skip to Step 4.

Step 3. To select a different Physical Number, type it in. A fully expanded system would have Physical Numbers from “001” through “500”; “000” is reserved for Physical

Numbers without corresponding room stations.

* The new number will flash in the “Station” window.

Step 4. When the desired Physical Number is displayed, press

Funct.

The

Architectural Numbers will flash in the “Station” window, and an “A” will appear in the “Sched” window.

Step 5. To change the Architectural number, type in the new one (any number from “00 1” to

“999

station, “000” for any unused Physical Number). Push

Enter

to store the new Architectural Number.

for an active

* The “Sched” window will change to “P,” and the

“Station” window will show the next-highest Physical Number.

Step 6. Repeat Steps 3 through 5 for each number you want to check or change. When you are finished, use the left cursor (t) to move back to the “Mode” window. Enter a different number to program in another “Comm” mode, or enter “0” to return the 2524 to the Clock Run Mode.

Mode 2 (Zones and Scanning)

This mode specifies the zones for each station, and determines which stations can bc monitored and regularly checked for electrical faults (supervised). You can’ also use this mode to find a station’s Physical Number.

Step 1. If necessary, enter the “Comm” programming function. When the “Mode” window is flashing, type in

“2 .”

* The “Mode”’ window will flash “2,” the “Sched” window will read “A,” and the “Station” (“Time”) windows will show the Architectural Number assigned to the lowest Physical Number in

USC

(usually

Page

10 4190

2524

ChronoCom Programming

Physical Number ”001”). Note that the 2524 will skip past unused Physical Numbers- those assigned

“000” in place of an Architectural Number. The

“Zones” LEDs will show which zones have been assigned to the station, and the first two “Days” LEDs will light if the station has been given the monitoring and supervising functions, respectively.

Step 2. Press the right cursor (+) to make the “Station” windows flash. To select a different

Architectural

Number, either push Enter to display the next one in numerical order, or type in the desired number.

* The “Station” windows will show the new number.

Step 3. You can use the Funct key here to toggle between the Physical and Architectural Numbers for this station.

* The number will change, and the “Sched” window will read “A” or “P" to show which number is displayed. When the Physical Number is displayed, the

“P” will flash, indicating that you must toggle back to the Architectural Number before you can continue programming.

Step

4.

To program this station, push + to flash the

“Zones” LEDs. Use keys 1-8 to toggle the respective zones on and off.

* Selected LEDs will alternately light for a half-second and darken for a half-second. Those not selected will remain off unless none is selected; in the latter case, the entire block will alternately light for a half-second and darken for one-and-a-half seconds.

Step 5. Press + to flash the “Days” LEDs. Use numerical

keys 1 and 2 to toggle the first two LEDs on and off. Turn

LED 1 on to select the supervising function for this station, and LED 2 to select the monitoring function.

* When selected, these LEDs will alternately turn on for a half-second and turn off for a half-second. If neither is selected, all seven “Days” LEDs will alternately turn on for a half-second and turn off for one-and-a-half seconds.

Step 6. Check all of the programming for this station.

When all is satisfactory, push Enter.

* The 2524 will store the information and display the next “non-zero” Architectural Number. The flashing cursor will be in the “Station” windows.

Step 7. Repeat Steps 2-6 for any other station you wish to review or program. To exit this programming mode, use the left cursor (c) to flash the ”Mode” window, then enter another number to select a different “Comm” programming mode, or enter “0” to return to the Clock Run Mode.

Mode 3 (System Options)

This

mode is used to activate optional features of the unit. Monitoring and supervising have already been explained, in “Comm” Mode 2.

TC4200 Display

This optional Vacuum Fluorescent Display will normally show the time and date. In this mode, you can program the 2524 to display either normal or priority call-ins, both types, or neither. When there are no call-ins, the display will resume showing the time and date. Note that this programming option does not affect the 2524’s front-panel display.

Automatically Connect Priority Call-ins

This function causes the 2524 to automatically

connect a priority call-in to an optional intercom control panel. If this function is not selected, a priority call-in will be signaled at the 2524 and the control panel, but the user will have to press a button to establish communications with the caller; the user will also have the option of making a call or performing another function before answering a priority call-in.

Remote Phone

A “Remote Phone” can be installed in a different location from the 2524 to answer call-ins, and make All Pages.

Step 1. If necessary, enter the “Comm” programming function. When the “Mode” window is flashing, type in

“3.”

*

The “Mode” window will flash

“3,”

the “Station”

(“Time”) window will read “SELE” (“Select”), and the “Zones” LEDs will light to show which optional functions have been selected. If none has been selected, all the LEDs will remain off.

Step 2. Press the right cursor (+) to flash the “Zones”

LEDs.

* Selected LEDs will turn on and off every second.

Those not selected will remain off unless none is selected; in the latter case, the entire block of LEDs will alternately flash on for a half-second and turn off for a second-and-a-half.

Step 3. Use keys

l-6

to toggle the respective LEDs on and off. The following table shows the function associated with each LED:

1 "Zones” LED No. 1 Function when Selected

Enable Monitor function.

Enable Supervision function.

Display normal call-ins on TC4200.

Display priority call-ins on TC4200.

Automatically connect priority callins to the intercom control panel.

Enable Remote Phone.

[Future.]

Mode

4 (Monitoring Duration)

The monitoring function has already been explained under in the “Planning” section of this manual. This setting determines how long the 2524 will remain connected to each station as it cycles through the stations selected in “Comm” Mode 2.

Step 1. If necessary, enter the “Comm” programming function. When the “Mode” window is flashing, type in

“4 .”

* The “Mode” window will flash “4,” the left “Station” window will read “du” (“Duration”), and the right

“Station” window will show the current setting.

4/90

Page

Step 2. Press the right cursor (+) to flash the right

“Station” window. You may type in any number of seconds, from “01” to “15.” When the desired value appears,

The “Mode” window will flash, and the “Station” window will light steadily with “du” and the value you entered.

Step 3. Enter a different number to select another

“Comm” programming mode, or enter “0” to return to the

Clock Run Mode.

Mode 5 ‘(Call-in Sensitivity)

This mode is used to adjust Pot RP1 on the 2524 for call-in sensitivity; you must do this before activating the call-scanning function in Mode E.

Step 1. Select a station to use for this adjustment.

Temporarily install a 1500 fI resistor across its call-in wires

(its “‘I”’ and “G” terminalss on the rear of its relay panel).

Step 2. If necessary,, enter the “Comm” programming mode. When the “Mode” window is flashing, enter a “5.”

* The “Mode” window will flash a “5,” and the “Station” windows will display “000.”

Step 3. Press -b.

* The “Station” windows will flash.

Step 4. Enter the three-digit Architectural Number of the selected station. If you enter the wrong number, push

CIear and return to Step 2. When the desired Architectural

Number is flashing in the “Station” windows, press Funct.

* The display will now “freeze” with Mode 5 and the

Architectural Number. This signifies that the unit is continuously scanning the station.

Step 5. Face the back of the 2524 and locate RP1: its

dark blue thumbwheel can be accessed near the left end of the terminal slot, just to the right of the four-pin wire-wrap terminal.

Step 6. Use a small, flat-blade screwdriver to turn this

pot completely counterclockwise. Then slowly turn it back clockwise until the 2524 starts to “beep.” Mark this position on the pot.

Step 7. Resume moving the pot clockwise until the beeping stops. Mark this position on the pot, too.

Step 8. Move the pot back to the middle of your two markings. Remove the resistor from the call-in wires.

Step 9. Push Clear.

* The “Mode” window will flash “5,” and the “Station” windows will show “000” steadily.

Step 10. Enter a “0” to return the 2524 to the Clock

Run Mode.

Step 11. Have someone send normal and priority call-

ins from a nearby and a distant station. If necessary, try a different setting between the two markings on RP1.

Mode 0 (Run)

When the 2524 is in the Run Mode (“0”), the

Clock/Comm button will toggle the unit between the

clock and communications modes. Normally, there is no reason to select the communications mode. Whenever a call-in comes in or the user dials a number, the 2524 will automatically switch to the communications mode, and then switch back when all communications have ended.

Putting the 2524 in the “Comm” mode when there are no calls in progress will blank the front-panel displays (except for the “Mode” window).

2524 ChronoCom Programming

Work Sheet for Custom Secondary-Clock Code

Bit

Value I Bit

Value

03

04 11

05 12

13

07 14

Description

Starting hour: any number between “01” and “12.” Enter "80" to select every hour.

Starting minute: any number between ”00” and ”59.” Enter “80” to select every minute.

Starting second: any number between “00” and “59.” Enter “80” to select every second.

How long the relay should remain “on”: indicate whether your units are seconds ("S") or minutes (“M”).*

Number of cycles.

How long the relay should remain “off’: indicate whether your units are seconds (“S”) or minutes (“M").*

Select the output relay that this seven-byte block will control: enter “1” for Out 5” or Out 7"; enter “2” for Out 6 or Out 8.**

* The way you enter this number during programming

will determine whether the 2524 interprets it as minutes or seconds: after typing the number, press Enter for seconds or Funct for minutes.

**You must coordinate three factors to direct a sevennumber block to a particular clock or motor in the clock:

4 You must wire the clock to a particular relay (Out 5.

Out 6, Out 7, or Out 8).

In Mode A, you must enter the Custom Code as either the first correction code (the only choice when only one code is used) or the second code. In a singlecode system, the first correction code controls Out 7 and Out 8; in a two-code system, the first code controls Out5 and Out 6, and the second code controls Out 7 and Out 8.

Use the seventh number of the block to designate the odd or even relay.

Note: Although Mode! A and the seventh number in the block each designate two possible relays, in combination they designate only one relay. For example, choosing the second code in Mode A limits the relay choice to 7 or 8; entering a “2” in the seven-number block designates Relay 6 or 8. Only Out 8 matches both these designations.

Example

The following table shows how the correction code for

Rauland analog clocks (regular Correction Code 1) would be set up as a special code. This is done for illustration only; you would not usually need to enter a regular code as a special code (the only exception would be entering a simple standard code for each seven-number block, in order to get two corrections in a single code and thereby free up two output terminals).

Commentary:

Entry 1: “80” = hourly correction.

Entry 2: “00” = start the correction pulse during the

“zero” minute.

Entry 3: “00” = start the correction pulse on the “zero” second.

Entry 4: “25” = close the relay for 25 seconds per pulse.

Entry 5: “00” = only one correction pulse.

Entry 6: “00” matches Entry 5: no time between pulses, since there is only one pulse.

Entry 7: “01 ” = send this correction out the odd-numbered relay.

Entry 8: “06” = start the 12-hour correction during the sixth hour.

Entry 9: “00” = start the 12-hour correction during the

“zero” minute.

Entry 10: “25 ” = start the correction 25 seconds after the minute. Note that the standard code would start this at “00” seconds. The difference here is that we are using the same output terminal for both the hourly and the

12-hour correction (see Entries 7 and 14). Therefore, we have to wait 25 seconds for the hourly pulse to end (Entry

4) before beginning this pulse.

Entry 11: “24” = close the relay for 24 minutes.

Entry 12: (Like Entry 5.)

Entry 13: (Like Entry 6.).

Entry 14: (Like Entry 7.)

4/90

Page 13

Page 14

2524 ChronoCom Programming

Table 1. Clock Modes A-P

Id.

I-

holiday entries; erase them all.

Table 2. Clock Modes l-6

Date.

Function

1 2 ITime.

1 3 1

Enter Events.

I 4

Review, edit, or delete events.

1 Duration for each zone.

6 Select active zones and schedules.

[Future.]

I 8

I [Future.]

9

[Future. ]

Table

3.

Intercom Modes

Mode

Function

Architectural

Number for each speaker.

2 Enter and review intercom zones; monitor and supervision bits for each speaker.

3

I 4

Enable or disable the system’s monitor and supervision functions.

Duration for monitoring.

I 5

Adjust call-in sensitivity.

6 [Future.]

7 [Futute.]

8 [Future.]

9

[Future.]

Table 4. Cross-Reference to tbe Major Functions

Function

Call-in configuration

Mode

Mode E.

Intercom Mode

3.

Intercom Mode 5.

Call-in sensitivity

Clock Codes

Clock-event entry.

I Modes A and B.

Clock Mode

3.

Clock-event detailed re- Clock Mode 4.

view and edit.

Holiday-event detailed re- Mode D.

Holiday-event overview Mode F.

and erase all.

Monitoring

Intercom Mode 2-4. Activated in Intercom Run

Mode

Music Clock Modes

3

and 4

Numbers: room (Architec- 1 Intercom Modes 1 and 2.

tural) and line (physical)

Schedules

Clock Modes

3,4,

and 6.

Supervision

Intercom Modes 2 and

3

Time and date.

Clock Mode 1.

Time-change (Daylight

Savings)

Time-correction Mode A.

Zones

Zones for clock events.

Zones for paging.

Clock Modes

3, 4, 5,

and 6.

Reduced by codes in Mode

A. Clock Modes

C and D.

3-6;

Modes

Intercom Mode 2.

Table 5. Factory Settings

Mode Setting

A Correction Code “0 1”

E No. of SC’s = 0; Comm. Scanning disabled

Clock 5

“03” sec., all zones

Clock 6 Zones l-6 selected; Sched. 1

Comm.

3

Mon., Sup., Auto Answ., & Rem. Ph. disabled; normal and priority call-in enabled

Comm. 4 Monitor dur.: “03” seconds

Notes for

Table 5: 1. The

time

and dnte nre not set, nnd no events or station programming are entered.

2. In “Comm” Mode

only

the two call-in types are enabled.

These will not run unless Mode E is changed.

However,

should the “Comm” function be activated, these two call-in types will usually be wanted.

4/90

Ciao! Sono un chatbot AI specificamente addestrato per assisterti con il rauland 2524 ChronoCom Manuale di programmazione. Ho esaminato attentamente il documento e posso aiutarti a individuare le informazioni di cui hai bisogno o spiegare il contenuto in termini chiari e semplici. Che tu stia cercando indicazioni su funzionalità specifiche, passaggi per la risoluzione dei problemi o l'uso generale, non esitare a fare domande. Più dettagli fornisci sulle tue esigenze o dubbi, più accuratamente e efficacemente potrò aiutarti!

L''assistente sta scrivendo

L''assistente non è disponibile. Riprova più tardi.

ChronoCom TM Master Clock and

Intercom Controller

Programming

Table of Contents

General Information

2

Programming Summary 2

Planning

3

Clock Modes A-F 5

Clock

l-6 7

Communication Modes 1 0

2524

ChronoCom Programming

Work Sheet for Custom Secondary-Clock Code

13

13

Programming Charts

14

General Information

Description

anuals

Power-up

Programming Summary

Sequence

P

Access to Programming

Methods

Planning

2524 ChronoCom Programming

Exiting

Information Needed

Because

5

Planning Charts

2524 ChronoCom Programming

3

3,

3

2524 ChronoCom Programming

Mode B (Custom Clock Code)

Mode C (Holidays and Time Changes)

6

3.

This

Mode D (Edit Holiday events)

Mode E (Relay Panels, Comm Activation)

This

2524 ChronoCom Programming

Mode F

(Events: Totals and Erase All)

Clock Modes

Mode 1 (Date)

2524 ChronoCom Programming

Mode

2

(Time)

Mode 3 (Enter Regular Events)

This

“3,”

3

3

Mode 4

(Edit Regular Events)

This

2524 ChronoCom Programming

Mode 5 (Zone Duration)

This

Mode 6 (Activate Zones and Schedules)

This

3

3.

Mode 0 (Run)

The

Communication

Modes

Entering the "Comm”

Modes

Mode 1 (Room Numbers)

ADEMCO Vista-128FB Installation And Setup Manual