D-Link | DGS-1500-20 | Datasheet | D-Link DGS-1500-20 network switch

Switching | DGS-1500 SmartPro Family
5
DGS-1500 SmartPro Family
Switching | DGS-1500 SmartPro Family
6
Switching | DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
dlink
Software Features
Stackability
• Virtual Stacking/Clustering
of up to 32 units
- Supports D-Link Single IP Management
L2 Features
• MAC Address Table
- 16 K entries
• Flow Control
- 802.3x Flow Control
- HOL Blocking Prevention
• IGMP Snooping
- IGMP v1/v2 Snooping
- Supports 256 IGMP groups
- Supports at least 64
static multicast addresses
- IGMP per VLAN
- Supports IGMP Snooping Querier
• Spanning Tree Protocol
- 802.1D STP
- 802.1w RSTP
• Loopback Detection
• 802.3ad Link Aggregation
- DGS-1500-20: Max. 10 groups
per device, 8 ports per group
• DGS-1500-28/DGS-1500-28P4: Max.
14 groups per device, 8 ports per group
- DGS-1500-52: Max. 26 groups per
device, 8 ports per group
• Port Mirroring
- One-to-One
- Many-to-One
- Supports Mirroring for Tx/Rx/Both
• Cable Diagnostics
• Configurable MDI/MDIX
• Multicast Filtering
- Forwards all unregistered groups
- Filters all unregistered groups
• Jumbo Frame
- Up to 10,000 bytes
• LLDP
• LLDP-MED
• L2 Multicast Filtering
VLAN
• 802.1Q
• VLAN Group
- Max. 4K static VLAN groups
- Max. 4094 VIDs
• GVRP
- Up to 256 dynamic VLANs
• Asymmetric VLAN
• Auto Voice VLAN
- Max. 10 user defined OUI
- Max. 8 default OUI
• Auto Surveillance VLAN
Software Features
QoS (Quality of Service)
• 802.1p Quality of Service
• 4 queues per port
• Queue Handling
- Strict
- Weighted Round Robin (WRR)
• CoS based on
- 802.1p Priority Queues
- DSCP
- ToS5
- IPv6 Traffic Class5
- IPv6 flow label5
- TCP/UDP port5
• Bandwidth Control
• Port-based (Ingress/Egress, min.
granularity 10/100/1000 is 64 Kb/s)
L3 Features
• ARP
- 64 Static ARP
- Supports Gratuitous ARP
• IPv6 Neighbour Discovery (ND)5
• IP Interface
- Supports 4 interfaces
L3 Routing
• Default Routing
• Static Routing
- 32 IPv4 Static Route Entries
- Max. 128 IPv4 Host Routes
Access Control List (ACL)
• DGS-1500-20/28/28P4
- Max. 50 profiles
- Max. 200 rules shared by profiles
- Each rule can be associated with
a single port or multiple ports
• DGS-1500-52:
- Max. 50 profiles
- Max. 450 rules shared by profiles
- Each rule can only be associated
with a single port
• ACL based on
- MAC Address
- IPv4 Address (ICMP/IGMP/TCP/UDP)
- 802.1p
- DSCP Ethernet type
Security
• 802.1X Port-based Access Control
• Port Security
- Supports up to 64 MAC
addresses per port
• Broadcast/Multicast/
Unicast Storm Control
• D-Link Safeguard EngineTM
• DHCP Server Screening
• IP-MAC-Port Binding5
- Supports 512 address binding entries
- ARP mode
- Supports DHCP Snooping
• ARP Spoofing Prevention
- Max. 64 entries
• Traffic Segmentation
• SSL
- Supports v1/v2/v3
- Supports IPv65
AAA
• 802.1X Authentication
- Supports local/RADIUS database
- Supports Port-based access control
- Supports EAP, OTP, TLS, TTLS, PEAP
• IPv6 RADIUS Server5
MIB
• 1213 MIB II
• 1493 Bridge MIB
• 1907 SNMP v2 MIB
• 1215 Trap Convention MIB
• 2233 Interface Group MIB
• D-Link Private MIB
• LLDP MIB
• Power-Ethernet MIB6
OAM
• Cable Diagnostics
• Factory Reset
Management
• Web-based GUI
• Single IP Management
• Compact CLI
• Telnet Server
• TFTP Client
• Configurable MDI/MDIX
• SNMP
- Supports v1/v2/v3
• SNMP Trap
• Trap for SmartConsole Utility
Optional SFP Transceivers
DGS-1500-28P will be released in late 2011.
5 Will be available in a future release in 2012. IPv6 Ready Logo Phase II will be obtained in the future.
6
Available for DGS-1500-28P only.
• Backup/Upgrade firmware
• Smart Wizard
- Max. 500 log entries
• BootP/DHCP Client
• SNTP
• ICMP v65
• IPv4/v6 Dual Stack5
• DHCP Auto Configuration
• Debug Command
• Time Setting
- SNTP
• RMON1
• Trusted Host
• Time-based PoE6
• User Account
• Upload/Download Configuration file
Green
• Power Saving by:
- Link Status
- Cable Length
- LED Shutoff
- Port Standby
- System Hibernation
Security Features
• Access Control List secures network
• D-Link Safeguard Engine protects CPU from
Broadcast/Multicast/Unicast Flooding
• Port Security supports 64 MACs per port
• ARP Spoofing Prevention
• SSL
Certification
• IPv6 Core Ready Logo Phase II5
Intuitive Management
Optional WDM SFP Transceivers
Supported by DGS-1500-20/28/28P4
Supported by DGS-1500-20/28/28P4/52
DGS-712
1000BASE-T Copper
DEM-330T/R
DV-600S
DEM-310GT
1000BASE-LX, Single-mode, 10 km
D-View 6.0 Network Management
System (Standard Edition)
DV-600P
D-View 6.0 Network Management
System (Professional Edition)
1000BASE-SX, Multi-mode, 550 m
DEM-312GT2 1000BASE-SX, Multi-mode, 2 km
DEM-314GT
1000BASE-LHX, Single-mode, 50 km
DEM-315GT
1000BASE-ZX, Single -mode, 80km
Supported by DGS-1500-52
DGS-712
1000BASE-T Copper
DEM-310GT
1000BASE-LX, Single-mode, 10 km
DEM-311GT
1000BASE-SX, Multi-mode, 550 m
DEM-331T/R
1000BASE-LHX, Single-mode, 50km
DEM-315GT
1000BASE-ZX, Single-mode, 80km
DEM-210
100BASE-BX, Single-mode, 15 km
DEM-211
100BASE-BX, Multi-mode, 2 km
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 40 km
VoIP Deployment
• Highest priority for VoIP services
• Auto Voice VLAN
QoS (Quality of Service)
Optional Redundant Power Supply
Supported by DGS-1500-28P
DEM-330T/R
DPS-700
DEM-312GT2 1000BASE-SX, Multi-mode, 2 km
DEM-314GT
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 10 km
Supported by DGS-1500-52
DEM-331T/R
• SmartConsole utility or Web-based GUI
• Single IP Management (Virtual Stacking)
• Built-in SNMP MIB for remote NMS
(D-View 6.0)
Optional Management Software
Supported by DGS-1500-20/28/28P4
DEM-311GT
4
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 10 km
589 Watts Redundant Power Supply
370 Watts PoE Power Budget
• Supports IEEE 802.1p QoS,
up to four Priority Queues per port
• Bandwidth Control
• DSCP
Advanced Features
• Layer 3 Static Routing
• IPv6 support2
• Auto Surveillance VLAN
• Loopback Detection automatically disables
a port or VLAN when a loop is detected
• Cable Diagnostics allows administrators
to determine cable status
• Configurable MDI/MDIX
• LLDP/LLDP-MED
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 40 km
Trap & Logs
• SNMP Trap
• Trap for SmartConsole Utility
Online Help
• Link to local support website
• Online User Guide
For further information: www.dlink.eu
4
DGS-1500-28P will be released in late 2011.
Will be available in a future release in 2012. IPv6 Ready Logo Phase II will be obtained in the future.
Available for DGS-1500-28P only.
5 4
• System Log
• IEEE 802.3az EEE
• Power saving via LED and Port shutoff
• Power saving via Port Standby
• Power saving via System Hibernation
• Power saving via Cable Length detection
• Power saving via Link Status detection
• Time-based PoE (DGS-1500-28P1 only)
Optional Products
RFC Standard Compliance
• RFC 783 TFTP
• RFC 854 Telnet Server
• RFC 951 BootP/DHCP Client
• RFC 1157 SNMP v1, v2, v3
• RFC 1213 MIB II
• RFC 1215 MIB Traps Convention
• RFC 1350 TFTP
• RFC 1493 Bridge MIB
• RFC 1769 SNTP
• RFC 1542 BootP/DHCP Client
• RFC 1901 SNMP v1, v2, v3
• RFC 1907 SNMP v2 MIB
• RFC 1908 SNMP v1, v2, v3
• RFC 2068 FCS
• RFC 2131 BootP/DHCP Client
• RFC 2138 RADIUS Authentication
• RFC 2139 RADIUS Authentication
• RFC 2233 Interface Group MIB
• RFC-2246 SSL
• RFC 2475
• RFC 2570 SNMP v1, v2, v3
• RFC 2575 SNMP v1, v2, v3
• RFC 2598 CoS
• RFC 2616 FCS
• RFC 2618 RADIUS Authentication
• RFC 2819 RMON v1
• RFC 2865 RADIUS Authentication
• RFC 3164 System Log
• RFC 3195 System Log
• RFC 3411-17 SNMP
• RFC 3621 Power Ethernet MIB
Green Technology
6
C
US
ACN 052 202 838
I
D-Link European Headquarters. D-Link (Europe) Ltd., D-Link House, Abbey Road, Park Royal, London, NW10 7BX. Specifications are subject to change without notice. D-Link is a registered
trademark of D-Link Corporation and its overseas subsidiaries. All other trademarks belong to their respective owners. ©2011 D-Link Corporation. All rights reserved. Europe Release September 2011
D-Link’s DGS-1500 Series SmartPro switches
are designed for businesses which require
functions such as L3 Static Routing and Single
IP Management (Virtual Stacking) without
upgrading to a managed switch. This series
integrates advanced management and
security functions that are similar to those
of a managed switch, but less complex.
The switches feature D-Link GreenTM 3.0
technology which enables significant power
savings. Additionally, the DGS-1500-28P1’s
10/100/1000 Mbps ports are PoE-enabled,
offering ease-of-use and green features like
Time-based PoE, which enables the power
to the port to be shut off at a predetermined
time. Compliant with 802.3af and 802.3at,
these switches are capable of feeding power
to devices of up to 30 Watts. Management
options include SNMP, Web Management,
SmartConsole Utility, and Compact CLI. The
series also supports ACL filtering and D-Link’s
Safeguard Engine to protect the network.
The DGS-1500-20 and DGS-1500-28 both
feature a fanless design. The fanless design
allows them to emit less heat and noise than
a standard switch, making them suitable for
office environments. The DGS-1500-28P1 and
DGS-1500-52 both feature smart fans. Using
a thermal sensor that can detect temperature
change, the smart fans can react accordingly
by utilising different fan speeds for different
temperatures.
Advanced Features
The DGS-1500 Series integrates advanced
features such as Virtual Stacking and Layer 3
features like Static Routing. Virtual Stacking
reduces the number of IP addresses needed
on a network by configuring up to 32 devices
to appear as a single unit with one IP address.
This simplifies network management for small
workgroups and allows for switches to be
added without special cabling.
1
2
Extensive Layer 2 Features
These switches are equipped with a complete
lineup of Layer 2 features including IGMP
Snooping, Port Mirroring, Spanning Tree, and
Link Layer Discovery Protocol (LLDP). The IEEE
802.3x Flow Control function allows servers to
directly connect to the switch for fast, reliable
data transfer. At 2000 Mbps Full Duplex,
the Gigabit ports provide high-speed data
pipes to servers with minimum data transfer
loss. Network maintenance features include
Loopback Detection and Cable Diagnostics.
Loopback Detection is used to detect loops
created by a specific port or VLAN and
automatically shut down the affected port or
VLAN. The Cable Diagnostics feature, designed
primarily for adminstrators and customer
service representatives, can quickly discover
the type of error on cables and determine the
cable quality.
QoS, Bandwidth Control
The DGS-1500 Series supports Auto
Surveillance VLAN (ASV) and Auto Voice VLAN,
which are best suited for VoIP and video
surveillance deployments. Auto Surveillance
VLAN is a new, industry-leading technology
built into D-Link Smart Switches. This
technology consolidates data and surveillance
video transmission through a single SmartPro
switch, thus sparing businesses the expense
of maintaining dedicated hardware and
facilities. ASV also ensures the quality of
real-time video for monitoring and control
without compromising the transmission of
conventional network data. The Auto Voice
VLAN technology enhances VoIP service by
automatically placing voice traffic from an
IP phone to an assigned VLAN. With higher
priority and an individual VLAN, these features
guarantee the quality and security of VoIP
traffic. Furthermore, the DSCP markings on
Ethernet packets enable different levels of
service to be assigned to network traffic.
DGS-1500-28P will be released in late 2011.
IPv6 Ready Logo Phase II will be obtained in the future. IPv6 support will be available in a future release.
Switching | DGS-1500 SmartPro Family
2
Switching | DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
Rapid Response Support
If the worst should happen to your network you
need the very best support and fast. Downtime
costs your business money. D-Link Assist
maximises your uptime by solving technical
problems quickly and effectively. Our highlytrained technicians are on standby around the
clock, ensuring that award-winning support is
only a phone call away.
With a choice of three affordable service offerings
covering all D-Link business products, you can
select the package that suits you best:
D-Link Assist Gold - for comprehensive
24-hour support
D-Link Assist Gold is perfect for mission-critical
environments where maximum uptime is a high
priority. It guarantees four hour around-the-clock
response. Cover applies 24/7 for every day of the
year including holidays.
D-Link Assist Silver - for prompt same-day
assistance
D-Link Assist Silver is designed for ‘high
availability’ businesses that require rapid response
within regular working hours. It provides a four
hour response service Monday to Friday from 8am
to 5pm, excluding holidays.
D-Link Assist Bronze - for guaranteed response
on the next business day
D-Link Assist Bronze is a highly cost-effective
support solution for less critical environments.
Response is guaranteed within eight business
hours Monday to Friday from 8am to 5pm,
excluding holidays.
D-Link Assist can be purchased together with
any D-Link business product. So whether you’re
buying switching, wireless, storage, security or IP
Surveillance equipment from D-Link, your peace
of mind is guaranteed. D-Link Assist also offers
installation and configuration services to get your
new hardware working quickly and correctly.
Switching | DGS-1500 SmartPro Family
3
As a result, these voice and video packets
take precedence over other packets. In
addition, with Bandwidth Control, network
administrators can reserve bandwidth for
important functions that require more
bandwidth or might require high priority.
Secure your Network
D-Link’s innovative Safeguard Engine protects
the switches against traffic flooding caused
by virus attacks. The switches also support
802.1X port-based authentication, allowing
the network to be authenticated through
external RADIUS servers. In addition, the Access
Control List (ACL) feature enhances network
security and helps to protect the internal IT
network by screening traffic based on MAC
or IP addresses. The DGS-1500 Series includes
ARP Spoofing Prevention, which protects from
attacks on the Ethernet network that may allow
an intruder to sniff data frames, modify traffic,
or bring traffic to a halt altogether by sending
fake ARP messages to the network. To prevent
ARP Spoofing attacks, the switch uses Packet
Control ACLs to block invalid packets that
contain fake ARP messages. For added security,
the DHCP Server Screening feature screens
rogue DHCP server packets from user ports to
prevent unauthorised IP assignment.
Versatile Management
The DGS-1500 Series provides a SmartConsole
utility and a web-based management interface
that enables administrators to remotely
control their network down to the port level.
The SmartConsole easily allows customers to
discover multiple D-Link Web Smart Switches
within the same L2 network segment. With
this utility, users do not need to change the
IP address of their PC. It also simplifies the
initial setup of the Smart Switches. Switches
within the same L2 network segment that
are connected to the user’s PC are displayed
1
DGS-1500-28P will be released in late 2011.
on screen for instant access. This allows
extensive switch configuration and basic setup
of discovered devices including password
changes and firmware upgrades. The DGS-1500
Series also supports D-View 6.0 and Compact
Command Line Interface (CLI) through Telnet.
D-View 6.0 is a Network Management System
that allows for the central management
of critical network characteristics such as
availability, reliability, resilience, and security.
CLI management of the switches is possible
via Telnet. This makes it possible to adjust basic
settings, passwords, configuration files, and
firmware with ease.
4
DGS-1500 SmartPro Family
Technical Specifications
Interfaces
General
DGS-1500-20
DGS-1500-28
DGS-1500-28P3
DGS-1500-52
16x Gigabit Ethernet
4x SFP
24x Gigabit Ethernet
4x SFP
24x Gigabit Ethernet
4x SFP
48x Gigabit Ethernet
4x SFP
Optional Redundant Power Supply
RPS-700
Full/Half Duplex
Full/half duplex for 10/100 Mbps speeds, Full duplex for 1000 Mbps speed
Media Interface Exchange
Switching capacity
Deploying the DGS-1500 Series in an Office Environment
Packet forwarding rate
Auto MDI/MDIX adjustment
40 Gbps
56 Gbps
56 Gbps
104 Gbps
29.8 Mpps
41.7 Mpps
41.7 Mpps
77.4 Mpps
Transmission method
Performance
Store-and-forward
Packet buffer
1 MB per device
16 K entries per device
MAC Address table
Up to 256 static MAC entries
Enable/disable auto-learning of MAC addresses
MAC Address update
D-Link Green Technology
D-Link is striving to take the lead in developing
innovative and power-saving technology that
does not sacrifice operational performance or
functionality. The DGS-1500 Series implements
D-Link Green Technology, which includes a
power saving mode, smart fan, reduced heat
dissipation, and cable length detection. The
power-saving features include being able to
schedule when to turn off LEDs and ports when
not in use, and when to make the switch enter
hibernation mode. The switches can also detect
the length of connected cables to automatically
adjust power usage by saving energy on
shorter cable connections of up to 20 metres.
The switches can also support power-saving
by link status, which drastically reduces power
consumption by automatically toggling
ports without a link to sleep mode.
The DGS-1500-28P1 and DGS-1500-52 both
feature built-in smart fans. Using a thermal
sensor that can detect temperature change, the
fans can react accordingly by utilising different
fan speeds for different temperatures. The
Smart Fan feature enables the built-in fans to
automatically turn on at a certain temperature,
providing continuous, reliable and eco-friendly
operation of the switch.
Services Router
DSR-1000N
802.3af
802.3at
PoE standard
PoE
PoE capable ports
1-24
PoE power budget
Max. 370 W (740 W
with external RPS)
100 to 240 VAC, 50/60 Hz internal universal power supply
AC Input
Power
Max. Power consumption
Standby power consumption
Dimensions (W x D x H)
Weight
LEDs
14.06 W
16.81 W
43.5 W
7.2 W
6.42 W
440 x 140 x 44 mm
440 x 210 x 44 mm
2.2 Kg
2.9 Kg
Power
Link/Act/Speed
22.05W
440 x 310 x 44 mm
4.1 Kg
Power
Fan
Link/Act/Speed
PoE
PoE max
RPS
Power
Link/Act/Speed
1G Fibre
Fans
1G Copper
Physical &
Environmental
Acoustics
Heat dissipation
0
0
2 smart fans
0 dBA
47.1 dBA (max)
47.97 BTU/hr
57.36 BTU/hr
-20 to 70° C
Operating humidity
0% to 95% non-condensing
Storage humidity
0% to 95% non-condensing
FCC Class A, CE Class A, ICES-003, VCCI Class A, C-Tick, BSMI
Emission (EMI)
3
148.42 BTU/hr
-5 to 50° C
Storage temperature
Safety
DGS-1500-28P will be released in late 2011 .
Power
Fan
Link/Act/Speed
0 dBA
Operating temperature
MTBF
440 x 250 x 44 mm
253,460 hours
236,739 hours
201,517 hours
cUL, LVD
Switching | DGS-1500 SmartPro Family
2
Switching | DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
Rapid Response Support
If the worst should happen to your network you
need the very best support and fast. Downtime
costs your business money. D-Link Assist
maximises your uptime by solving technical
problems quickly and effectively. Our highlytrained technicians are on standby around the
clock, ensuring that award-winning support is
only a phone call away.
With a choice of three affordable service offerings
covering all D-Link business products, you can
select the package that suits you best:
D-Link Assist Gold - for comprehensive
24-hour support
D-Link Assist Gold is perfect for mission-critical
environments where maximum uptime is a high
priority. It guarantees four hour around-the-clock
response. Cover applies 24/7 for every day of the
year including holidays.
D-Link Assist Silver - for prompt same-day
assistance
D-Link Assist Silver is designed for ‘high
availability’ businesses that require rapid response
within regular working hours. It provides a four
hour response service Monday to Friday from 8am
to 5pm, excluding holidays.
D-Link Assist Bronze - for guaranteed response
on the next business day
D-Link Assist Bronze is a highly cost-effective
support solution for less critical environments.
Response is guaranteed within eight business
hours Monday to Friday from 8am to 5pm,
excluding holidays.
D-Link Assist can be purchased together with
any D-Link business product. So whether you’re
buying switching, wireless, storage, security or IP
Surveillance equipment from D-Link, your peace
of mind is guaranteed. D-Link Assist also offers
installation and configuration services to get your
new hardware working quickly and correctly.
Switching | DGS-1500 SmartPro Family
3
As a result, these voice and video packets
take precedence over other packets. In
addition, with Bandwidth Control, network
administrators can reserve bandwidth for
important functions that require more
bandwidth or might require high priority.
Secure your Network
D-Link’s innovative Safeguard Engine protects
the switches against traffic flooding caused
by virus attacks. The switches also support
802.1X port-based authentication, allowing
the network to be authenticated through
external RADIUS servers. In addition, the Access
Control List (ACL) feature enhances network
security and helps to protect the internal IT
network by screening traffic based on MAC
or IP addresses. The DGS-1500 Series includes
ARP Spoofing Prevention, which protects from
attacks on the Ethernet network that may allow
an intruder to sniff data frames, modify traffic,
or bring traffic to a halt altogether by sending
fake ARP messages to the network. To prevent
ARP Spoofing attacks, the switch uses Packet
Control ACLs to block invalid packets that
contain fake ARP messages. For added security,
the DHCP Server Screening feature screens
rogue DHCP server packets from user ports to
prevent unauthorised IP assignment.
Versatile Management
The DGS-1500 Series provides a SmartConsole
utility and a web-based management interface
that enables administrators to remotely
control their network down to the port level.
The SmartConsole easily allows customers to
discover multiple D-Link Web Smart Switches
within the same L2 network segment. With
this utility, users do not need to change the
IP address of their PC. It also simplifies the
initial setup of the Smart Switches. Switches
within the same L2 network segment that
are connected to the user’s PC are displayed
1
DGS-1500-28P will be released in late 2011.
on screen for instant access. This allows
extensive switch configuration and basic setup
of discovered devices including password
changes and firmware upgrades. The DGS-1500
Series also supports D-View 6.0 and Compact
Command Line Interface (CLI) through Telnet.
D-View 6.0 is a Network Management System
that allows for the central management
of critical network characteristics such as
availability, reliability, resilience, and security.
CLI management of the switches is possible
via Telnet. This makes it possible to adjust basic
settings, passwords, configuration files, and
firmware with ease.
4
DGS-1500 SmartPro Family
Technical Specifications
Interfaces
General
DGS-1500-20
DGS-1500-28
DGS-1500-28P3
DGS-1500-52
16x Gigabit Ethernet
4x SFP
24x Gigabit Ethernet
4x SFP
24x Gigabit Ethernet
4x SFP
48x Gigabit Ethernet
4x SFP
Optional Redundant Power Supply
RPS-700
Full/Half Duplex
Full/half duplex for 10/100 Mbps speeds, Full duplex for 1000 Mbps speed
Media Interface Exchange
Switching capacity
Deploying the DGS-1500 Series in an Office Environment
Packet forwarding rate
Auto MDI/MDIX adjustment
40 Gbps
56 Gbps
56 Gbps
104 Gbps
29.8 Mpps
41.7 Mpps
41.7 Mpps
77.4 Mpps
Transmission method
Performance
Store-and-forward
Packet buffer
1 MB per device
16 K entries per device
MAC Address table
Up to 256 static MAC entries
Enable/disable auto-learning of MAC addresses
MAC Address update
D-Link Green Technology
D-Link is striving to take the lead in developing
innovative and power-saving technology that
does not sacrifice operational performance or
functionality. The DGS-1500 Series implements
D-Link Green Technology, which includes a
power saving mode, smart fan, reduced heat
dissipation, and cable length detection. The
power-saving features include being able to
schedule when to turn off LEDs and ports when
not in use, and when to make the switch enter
hibernation mode. The switches can also detect
the length of connected cables to automatically
adjust power usage by saving energy on
shorter cable connections of up to 20 metres.
The switches can also support power-saving
by link status, which drastically reduces power
consumption by automatically toggling
ports without a link to sleep mode.
The DGS-1500-28P1 and DGS-1500-52 both
feature built-in smart fans. Using a thermal
sensor that can detect temperature change, the
fans can react accordingly by utilising different
fan speeds for different temperatures. The
Smart Fan feature enables the built-in fans to
automatically turn on at a certain temperature,
providing continuous, reliable and eco-friendly
operation of the switch.
Services Router
DSR-1000N
802.3af
802.3at
PoE standard
PoE
PoE capable ports
1-24
PoE power budget
Max. 370 W (740 W
with external RPS)
100 to 240 VAC, 50/60 Hz internal universal power supply
AC Input
Power
Max. Power consumption
Standby power consumption
Dimensions (W x D x H)
Weight
LEDs
14.06 W
16.81 W
43.5 W
7.2 W
6.42 W
440 x 140 x 44 mm
440 x 210 x 44 mm
2.2 Kg
2.9 Kg
Power
Link/Act/Speed
22.05W
440 x 310 x 44 mm
4.1 Kg
Power
Fan
Link/Act/Speed
PoE
PoE max
RPS
Power
Link/Act/Speed
1G Fibre
Fans
1G Copper
Physical &
Environmental
Acoustics
Heat dissipation
0
0
2 smart fans
0 dBA
47.1 dBA (max)
47.97 BTU/hr
57.36 BTU/hr
-20 to 70° C
Operating humidity
0% to 95% non-condensing
Storage humidity
0% to 95% non-condensing
FCC Class A, CE Class A, ICES-003, VCCI Class A, C-Tick, BSMI
Emission (EMI)
3
148.42 BTU/hr
-5 to 50° C
Storage temperature
Safety
DGS-1500-28P will be released in late 2011 .
Power
Fan
Link/Act/Speed
0 dBA
Operating temperature
MTBF
440 x 250 x 44 mm
253,460 hours
236,739 hours
201,517 hours
cUL, LVD
Switching | DGS-1500 SmartPro Family
2
Switching | DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
Rapid Response Support
If the worst should happen to your network you
need the very best support and fast. Downtime
costs your business money. D-Link Assist
maximises your uptime by solving technical
problems quickly and effectively. Our highlytrained technicians are on standby around the
clock, ensuring that award-winning support is
only a phone call away.
With a choice of three affordable service offerings
covering all D-Link business products, you can
select the package that suits you best:
D-Link Assist Gold - for comprehensive
24-hour support
D-Link Assist Gold is perfect for mission-critical
environments where maximum uptime is a high
priority. It guarantees four hour around-the-clock
response. Cover applies 24/7 for every day of the
year including holidays.
D-Link Assist Silver - for prompt same-day
assistance
D-Link Assist Silver is designed for ‘high
availability’ businesses that require rapid response
within regular working hours. It provides a four
hour response service Monday to Friday from 8am
to 5pm, excluding holidays.
D-Link Assist Bronze - for guaranteed response
on the next business day
D-Link Assist Bronze is a highly cost-effective
support solution for less critical environments.
Response is guaranteed within eight business
hours Monday to Friday from 8am to 5pm,
excluding holidays.
D-Link Assist can be purchased together with
any D-Link business product. So whether you’re
buying switching, wireless, storage, security or IP
Surveillance equipment from D-Link, your peace
of mind is guaranteed. D-Link Assist also offers
installation and configuration services to get your
new hardware working quickly and correctly.
Switching | DGS-1500 SmartPro Family
3
As a result, these voice and video packets
take precedence over other packets. In
addition, with Bandwidth Control, network
administrators can reserve bandwidth for
important functions that require more
bandwidth or might require high priority.
Secure your Network
D-Link’s innovative Safeguard Engine protects
the switches against traffic flooding caused
by virus attacks. The switches also support
802.1X port-based authentication, allowing
the network to be authenticated through
external RADIUS servers. In addition, the Access
Control List (ACL) feature enhances network
security and helps to protect the internal IT
network by screening traffic based on MAC
or IP addresses. The DGS-1500 Series includes
ARP Spoofing Prevention, which protects from
attacks on the Ethernet network that may allow
an intruder to sniff data frames, modify traffic,
or bring traffic to a halt altogether by sending
fake ARP messages to the network. To prevent
ARP Spoofing attacks, the switch uses Packet
Control ACLs to block invalid packets that
contain fake ARP messages. For added security,
the DHCP Server Screening feature screens
rogue DHCP server packets from user ports to
prevent unauthorised IP assignment.
Versatile Management
The DGS-1500 Series provides a SmartConsole
utility and a web-based management interface
that enables administrators to remotely
control their network down to the port level.
The SmartConsole easily allows customers to
discover multiple D-Link Web Smart Switches
within the same L2 network segment. With
this utility, users do not need to change the
IP address of their PC. It also simplifies the
initial setup of the Smart Switches. Switches
within the same L2 network segment that
are connected to the user’s PC are displayed
1
DGS-1500-28P will be released in late 2011.
on screen for instant access. This allows
extensive switch configuration and basic setup
of discovered devices including password
changes and firmware upgrades. The DGS-1500
Series also supports D-View 6.0 and Compact
Command Line Interface (CLI) through Telnet.
D-View 6.0 is a Network Management System
that allows for the central management
of critical network characteristics such as
availability, reliability, resilience, and security.
CLI management of the switches is possible
via Telnet. This makes it possible to adjust basic
settings, passwords, configuration files, and
firmware with ease.
4
DGS-1500 SmartPro Family
Technical Specifications
Interfaces
General
DGS-1500-20
DGS-1500-28
DGS-1500-28P3
DGS-1500-52
16x Gigabit Ethernet
4x SFP
24x Gigabit Ethernet
4x SFP
24x Gigabit Ethernet
4x SFP
48x Gigabit Ethernet
4x SFP
Optional Redundant Power Supply
RPS-700
Full/Half Duplex
Full/half duplex for 10/100 Mbps speeds, Full duplex for 1000 Mbps speed
Media Interface Exchange
Switching capacity
Deploying the DGS-1500 Series in an Office Environment
Packet forwarding rate
Auto MDI/MDIX adjustment
40 Gbps
56 Gbps
56 Gbps
104 Gbps
29.8 Mpps
41.7 Mpps
41.7 Mpps
77.4 Mpps
Transmission method
Performance
Store-and-forward
Packet buffer
1 MB per device
16 K entries per device
MAC Address table
Up to 256 static MAC entries
Enable/disable auto-learning of MAC addresses
MAC Address update
D-Link Green Technology
D-Link is striving to take the lead in developing
innovative and power-saving technology that
does not sacrifice operational performance or
functionality. The DGS-1500 Series implements
D-Link Green Technology, which includes a
power saving mode, smart fan, reduced heat
dissipation, and cable length detection. The
power-saving features include being able to
schedule when to turn off LEDs and ports when
not in use, and when to make the switch enter
hibernation mode. The switches can also detect
the length of connected cables to automatically
adjust power usage by saving energy on
shorter cable connections of up to 20 metres.
The switches can also support power-saving
by link status, which drastically reduces power
consumption by automatically toggling
ports without a link to sleep mode.
The DGS-1500-28P1 and DGS-1500-52 both
feature built-in smart fans. Using a thermal
sensor that can detect temperature change, the
fans can react accordingly by utilising different
fan speeds for different temperatures. The
Smart Fan feature enables the built-in fans to
automatically turn on at a certain temperature,
providing continuous, reliable and eco-friendly
operation of the switch.
Services Router
DSR-1000N
802.3af
802.3at
PoE standard
PoE
PoE capable ports
1-24
PoE power budget
Max. 370 W (740 W
with external RPS)
100 to 240 VAC, 50/60 Hz internal universal power supply
AC Input
Power
Max. Power consumption
Standby power consumption
Dimensions (W x D x H)
Weight
LEDs
14.06 W
16.81 W
43.5 W
7.2 W
6.42 W
440 x 140 x 44 mm
440 x 210 x 44 mm
2.2 Kg
2.9 Kg
Power
Link/Act/Speed
22.05W
440 x 310 x 44 mm
4.1 Kg
Power
Fan
Link/Act/Speed
PoE
PoE max
RPS
Power
Link/Act/Speed
1G Fibre
Fans
1G Copper
Physical &
Environmental
Acoustics
Heat dissipation
0
0
2 smart fans
0 dBA
47.1 dBA (max)
47.97 BTU/hr
57.36 BTU/hr
-20 to 70° C
Operating humidity
0% to 95% non-condensing
Storage humidity
0% to 95% non-condensing
FCC Class A, CE Class A, ICES-003, VCCI Class A, C-Tick, BSMI
Emission (EMI)
3
148.42 BTU/hr
-5 to 50° C
Storage temperature
Safety
DGS-1500-28P will be released in late 2011 .
Power
Fan
Link/Act/Speed
0 dBA
Operating temperature
MTBF
440 x 250 x 44 mm
253,460 hours
236,739 hours
201,517 hours
cUL, LVD
Switching | DGS-1500 SmartPro Family
5
DGS-1500 SmartPro Family
Switching | DGS-1500 SmartPro Family
6
Switching | DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
dlink
Software Features
Stackability
• Virtual Stacking/Clustering
of up to 32 units
- Supports D-Link Single IP Management
L2 Features
• MAC Address Table
- 16 K entries
• Flow Control
- 802.3x Flow Control
- HOL Blocking Prevention
• IGMP Snooping
- IGMP v1/v2 Snooping
- Supports 256 IGMP groups
- Supports at least 64
static multicast addresses
- IGMP per VLAN
- Supports IGMP Snooping Querier
• Spanning Tree Protocol
- 802.1D STP
- 802.1w RSTP
• Loopback Detection
• 802.3ad Link Aggregation
- DGS-1500-20: Max. 10 groups
per device, 8 ports per group
• DGS-1500-28/DGS-1500-28P4: Max.
14 groups per device, 8 ports per group
- DGS-1500-52: Max. 26 groups per
device, 8 ports per group
• Port Mirroring
- One-to-One
- Many-to-One
- Supports Mirroring for Tx/Rx/Both
• Cable Diagnostics
• Configurable MDI/MDIX
• Multicast Filtering
- Forwards all unregistered groups
- Filters all unregistered groups
• Jumbo Frame
- Up to 10,000 bytes
• LLDP
• LLDP-MED
• L2 Multicast Filtering
VLAN
• 802.1Q
• VLAN Group
- Max. 4K static VLAN groups
- Max. 4094 VIDs
• GVRP
- Up to 256 dynamic VLANs
• Asymmetric VLAN
• Auto Voice VLAN
- Max. 10 user defined OUI
- Max. 8 default OUI
• Auto Surveillance VLAN
Software Features
QoS (Quality of Service)
• 802.1p Quality of Service
• 4 queues per port
• Queue Handling
- Strict
- Weighted Round Robin (WRR)
• CoS based on
- 802.1p Priority Queues
- DSCP
- ToS5
- IPv6 Traffic Class5
- IPv6 flow label5
- TCP/UDP port5
• Bandwidth Control
• Port-based (Ingress/Egress, min.
granularity 10/100/1000 is 64 Kb/s)
L3 Features
• ARP
- 64 Static ARP
- Supports Gratuitous ARP
• IPv6 Neighbour Discovery (ND)5
• IP Interface
- Supports 4 interfaces
L3 Routing
• Default Routing
• Static Routing
- 32 IPv4 Static Route Entries
- Max. 128 IPv4 Host Routes
Access Control List (ACL)
• DGS-1500-20/28/28P4
- Max. 50 profiles
- Max. 200 rules shared by profiles
- Each rule can be associated with
a single port or multiple ports
• DGS-1500-52:
- Max. 50 profiles
- Max. 450 rules shared by profiles
- Each rule can only be associated
with a single port
• ACL based on
- MAC Address
- IPv4 Address (ICMP/IGMP/TCP/UDP)
- 802.1p
- DSCP Ethernet type
Security
• 802.1X Port-based Access Control
• Port Security
- Supports up to 64 MAC
addresses per port
• Broadcast/Multicast/
Unicast Storm Control
• D-Link Safeguard EngineTM
• DHCP Server Screening
• IP-MAC-Port Binding5
- Supports 512 address binding entries
- ARP mode
- Supports DHCP Snooping
• ARP Spoofing Prevention
- Max. 64 entries
• Traffic Segmentation
• SSL
- Supports v1/v2/v3
- Supports IPv65
AAA
• 802.1X Authentication
- Supports local/RADIUS database
- Supports Port-based access control
- Supports EAP, OTP, TLS, TTLS, PEAP
• IPv6 RADIUS Server5
MIB
• 1213 MIB II
• 1493 Bridge MIB
• 1907 SNMP v2 MIB
• 1215 Trap Convention MIB
• 2233 Interface Group MIB
• D-Link Private MIB
• LLDP MIB
• Power-Ethernet MIB6
OAM
• Cable Diagnostics
• Factory Reset
Management
• Web-based GUI
• Single IP Management
• Compact CLI
• Telnet Server
• TFTP Client
• Configurable MDI/MDIX
• SNMP
- Supports v1/v2/v3
• SNMP Trap
• Trap for SmartConsole Utility
Optional SFP Transceivers
DGS-1500-28P will be released in late 2011.
5 Will be available in a future release in 2012. IPv6 Ready Logo Phase II will be obtained in the future.
6
Available for DGS-1500-28P only.
• Backup/Upgrade firmware
• Smart Wizard
- Max. 500 log entries
• BootP/DHCP Client
• SNTP
• ICMP v65
• IPv4/v6 Dual Stack5
• DHCP Auto Configuration
• Debug Command
• Time Setting
- SNTP
• RMON1
• Trusted Host
• Time-based PoE6
• User Account
• Upload/Download Configuration file
Green
• Power Saving by:
- Link Status
- Cable Length
- LED Shutoff
- Port Standby
- System Hibernation
Security Features
• Access Control List secures network
• D-Link Safeguard Engine protects CPU from
Broadcast/Multicast/Unicast Flooding
• Port Security supports 64 MACs per port
• ARP Spoofing Prevention
• SSL
Certification
• IPv6 Core Ready Logo Phase II5
Intuitive Management
Optional WDM SFP Transceivers
Supported by DGS-1500-20/28/28P4
Supported by DGS-1500-20/28/28P4/52
DGS-712
1000BASE-T Copper
DEM-330T/R
DV-600S
DEM-310GT
1000BASE-LX, Single-mode, 10 km
D-View 6.0 Network Management
System (Standard Edition)
DV-600P
D-View 6.0 Network Management
System (Professional Edition)
1000BASE-SX, Multi-mode, 550 m
DEM-312GT2 1000BASE-SX, Multi-mode, 2 km
DEM-314GT
1000BASE-LHX, Single-mode, 50 km
DEM-315GT
1000BASE-ZX, Single -mode, 80km
Supported by DGS-1500-52
DGS-712
1000BASE-T Copper
DEM-310GT
1000BASE-LX, Single-mode, 10 km
DEM-311GT
1000BASE-SX, Multi-mode, 550 m
DEM-331T/R
1000BASE-LHX, Single-mode, 50km
DEM-315GT
1000BASE-ZX, Single-mode, 80km
DEM-210
100BASE-BX, Single-mode, 15 km
DEM-211
100BASE-BX, Multi-mode, 2 km
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 40 km
VoIP Deployment
• Highest priority for VoIP services
• Auto Voice VLAN
QoS (Quality of Service)
Optional Redundant Power Supply
Supported by DGS-1500-28P
DEM-330T/R
DPS-700
DEM-312GT2 1000BASE-SX, Multi-mode, 2 km
DEM-314GT
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 10 km
Supported by DGS-1500-52
DEM-331T/R
• SmartConsole utility or Web-based GUI
• Single IP Management (Virtual Stacking)
• Built-in SNMP MIB for remote NMS
(D-View 6.0)
Optional Management Software
Supported by DGS-1500-20/28/28P4
DEM-311GT
4
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 10 km
589 Watts Redundant Power Supply
370 Watts PoE Power Budget
• Supports IEEE 802.1p QoS,
up to four Priority Queues per port
• Bandwidth Control
• DSCP
Advanced Features
• Layer 3 Static Routing
• IPv6 support2
• Auto Surveillance VLAN
• Loopback Detection automatically disables
a port or VLAN when a loop is detected
• Cable Diagnostics allows administrators
to determine cable status
• Configurable MDI/MDIX
• LLDP/LLDP-MED
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 40 km
Trap & Logs
• SNMP Trap
• Trap for SmartConsole Utility
Online Help
• Link to local support website
• Online User Guide
For further information: www.dlink.eu
4
DGS-1500-28P will be released in late 2011.
Will be available in a future release in 2012. IPv6 Ready Logo Phase II will be obtained in the future.
Available for DGS-1500-28P only.
5 4
• System Log
• IEEE 802.3az EEE
• Power saving via LED and Port shutoff
• Power saving via Port Standby
• Power saving via System Hibernation
• Power saving via Cable Length detection
• Power saving via Link Status detection
• Time-based PoE (DGS-1500-28P1 only)
Optional Products
RFC Standard Compliance
• RFC 783 TFTP
• RFC 854 Telnet Server
• RFC 951 BootP/DHCP Client
• RFC 1157 SNMP v1, v2, v3
• RFC 1213 MIB II
• RFC 1215 MIB Traps Convention
• RFC 1350 TFTP
• RFC 1493 Bridge MIB
• RFC 1769 SNTP
• RFC 1542 BootP/DHCP Client
• RFC 1901 SNMP v1, v2, v3
• RFC 1907 SNMP v2 MIB
• RFC 1908 SNMP v1, v2, v3
• RFC 2068 FCS
• RFC 2131 BootP/DHCP Client
• RFC 2138 RADIUS Authentication
• RFC 2139 RADIUS Authentication
• RFC 2233 Interface Group MIB
• RFC-2246 SSL
• RFC 2475
• RFC 2570 SNMP v1, v2, v3
• RFC 2575 SNMP v1, v2, v3
• RFC 2598 CoS
• RFC 2616 FCS
• RFC 2618 RADIUS Authentication
• RFC 2819 RMON v1
• RFC 2865 RADIUS Authentication
• RFC 3164 System Log
• RFC 3195 System Log
• RFC 3411-17 SNMP
• RFC 3621 Power Ethernet MIB
Green Technology
6
C
US
ACN 052 202 838
I
D-Link European Headquarters. D-Link (Europe) Ltd., D-Link House, Abbey Road, Park Royal, London, NW10 7BX. Specifications are subject to change without notice. D-Link is a registered
trademark of D-Link Corporation and its overseas subsidiaries. All other trademarks belong to their respective owners. ©2011 D-Link Corporation. All rights reserved. Europe Release September 2011
D-Link’s DGS-1500 Series SmartPro switches
are designed for businesses which require
functions such as L3 Static Routing and Single
IP Management (Virtual Stacking) without
upgrading to a managed switch. This series
integrates advanced management and
security functions that are similar to those
of a managed switch, but less complex.
The switches feature D-Link GreenTM 3.0
technology which enables significant power
savings. Additionally, the DGS-1500-28P1’s
10/100/1000 Mbps ports are PoE-enabled,
offering ease-of-use and green features like
Time-based PoE, which enables the power
to the port to be shut off at a predetermined
time. Compliant with 802.3af and 802.3at,
these switches are capable of feeding power
to devices of up to 30 Watts. Management
options include SNMP, Web Management,
SmartConsole Utility, and Compact CLI. The
series also supports ACL filtering and D-Link’s
Safeguard Engine to protect the network.
The DGS-1500-20 and DGS-1500-28 both
feature a fanless design. The fanless design
allows them to emit less heat and noise than
a standard switch, making them suitable for
office environments. The DGS-1500-28P1 and
DGS-1500-52 both feature smart fans. Using
a thermal sensor that can detect temperature
change, the smart fans can react accordingly
by utilising different fan speeds for different
temperatures.
Advanced Features
The DGS-1500 Series integrates advanced
features such as Virtual Stacking and Layer 3
features like Static Routing. Virtual Stacking
reduces the number of IP addresses needed
on a network by configuring up to 32 devices
to appear as a single unit with one IP address.
This simplifies network management for small
workgroups and allows for switches to be
added without special cabling.
1
2
Extensive Layer 2 Features
These switches are equipped with a complete
lineup of Layer 2 features including IGMP
Snooping, Port Mirroring, Spanning Tree, and
Link Layer Discovery Protocol (LLDP). The IEEE
802.3x Flow Control function allows servers to
directly connect to the switch for fast, reliable
data transfer. At 2000 Mbps Full Duplex,
the Gigabit ports provide high-speed data
pipes to servers with minimum data transfer
loss. Network maintenance features include
Loopback Detection and Cable Diagnostics.
Loopback Detection is used to detect loops
created by a specific port or VLAN and
automatically shut down the affected port or
VLAN. The Cable Diagnostics feature, designed
primarily for adminstrators and customer
service representatives, can quickly discover
the type of error on cables and determine the
cable quality.
QoS, Bandwidth Control
The DGS-1500 Series supports Auto
Surveillance VLAN (ASV) and Auto Voice VLAN,
which are best suited for VoIP and video
surveillance deployments. Auto Surveillance
VLAN is a new, industry-leading technology
built into D-Link Smart Switches. This
technology consolidates data and surveillance
video transmission through a single SmartPro
switch, thus sparing businesses the expense
of maintaining dedicated hardware and
facilities. ASV also ensures the quality of
real-time video for monitoring and control
without compromising the transmission of
conventional network data. The Auto Voice
VLAN technology enhances VoIP service by
automatically placing voice traffic from an
IP phone to an assigned VLAN. With higher
priority and an individual VLAN, these features
guarantee the quality and security of VoIP
traffic. Furthermore, the DSCP markings on
Ethernet packets enable different levels of
service to be assigned to network traffic.
DGS-1500-28P will be released in late 2011.
IPv6 Ready Logo Phase II will be obtained in the future. IPv6 support will be available in a future release.
Switching | DGS-1500 SmartPro Family
5
DGS-1500 SmartPro Family
Switching | DGS-1500 SmartPro Family
6
Switching | DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
DGS-1500 SmartPro Family
dlink
Software Features
Stackability
• Virtual Stacking/Clustering
of up to 32 units
- Supports D-Link Single IP Management
L2 Features
• MAC Address Table
- 16 K entries
• Flow Control
- 802.3x Flow Control
- HOL Blocking Prevention
• IGMP Snooping
- IGMP v1/v2 Snooping
- Supports 256 IGMP groups
- Supports at least 64
static multicast addresses
- IGMP per VLAN
- Supports IGMP Snooping Querier
• Spanning Tree Protocol
- 802.1D STP
- 802.1w RSTP
• Loopback Detection
• 802.3ad Link Aggregation
- DGS-1500-20: Max. 10 groups
per device, 8 ports per group
• DGS-1500-28/DGS-1500-28P4: Max.
14 groups per device, 8 ports per group
- DGS-1500-52: Max. 26 groups per
device, 8 ports per group
• Port Mirroring
- One-to-One
- Many-to-One
- Supports Mirroring for Tx/Rx/Both
• Cable Diagnostics
• Configurable MDI/MDIX
• Multicast Filtering
- Forwards all unregistered groups
- Filters all unregistered groups
• Jumbo Frame
- Up to 10,000 bytes
• LLDP
• LLDP-MED
• L2 Multicast Filtering
VLAN
• 802.1Q
• VLAN Group
- Max. 4K static VLAN groups
- Max. 4094 VIDs
• GVRP
- Up to 256 dynamic VLANs
• Asymmetric VLAN
• Auto Voice VLAN
- Max. 10 user defined OUI
- Max. 8 default OUI
• Auto Surveillance VLAN
Software Features
QoS (Quality of Service)
• 802.1p Quality of Service
• 4 queues per port
• Queue Handling
- Strict
- Weighted Round Robin (WRR)
• CoS based on
- 802.1p Priority Queues
- DSCP
- ToS5
- IPv6 Traffic Class5
- IPv6 flow label5
- TCP/UDP port5
• Bandwidth Control
• Port-based (Ingress/Egress, min.
granularity 10/100/1000 is 64 Kb/s)
L3 Features
• ARP
- 64 Static ARP
- Supports Gratuitous ARP
• IPv6 Neighbour Discovery (ND)5
• IP Interface
- Supports 4 interfaces
L3 Routing
• Default Routing
• Static Routing
- 32 IPv4 Static Route Entries
- Max. 128 IPv4 Host Routes
Access Control List (ACL)
• DGS-1500-20/28/28P4
- Max. 50 profiles
- Max. 200 rules shared by profiles
- Each rule can be associated with
a single port or multiple ports
• DGS-1500-52:
- Max. 50 profiles
- Max. 450 rules shared by profiles
- Each rule can only be associated
with a single port
• ACL based on
- MAC Address
- IPv4 Address (ICMP/IGMP/TCP/UDP)
- 802.1p
- DSCP Ethernet type
Security
• 802.1X Port-based Access Control
• Port Security
- Supports up to 64 MAC
addresses per port
• Broadcast/Multicast/
Unicast Storm Control
• D-Link Safeguard EngineTM
• DHCP Server Screening
• IP-MAC-Port Binding5
- Supports 512 address binding entries
- ARP mode
- Supports DHCP Snooping
• ARP Spoofing Prevention
- Max. 64 entries
• Traffic Segmentation
• SSL
- Supports v1/v2/v3
- Supports IPv65
AAA
• 802.1X Authentication
- Supports local/RADIUS database
- Supports Port-based access control
- Supports EAP, OTP, TLS, TTLS, PEAP
• IPv6 RADIUS Server5
MIB
• 1213 MIB II
• 1493 Bridge MIB
• 1907 SNMP v2 MIB
• 1215 Trap Convention MIB
• 2233 Interface Group MIB
• D-Link Private MIB
• LLDP MIB
• Power-Ethernet MIB6
OAM
• Cable Diagnostics
• Factory Reset
Management
• Web-based GUI
• Single IP Management
• Compact CLI
• Telnet Server
• TFTP Client
• Configurable MDI/MDIX
• SNMP
- Supports v1/v2/v3
• SNMP Trap
• Trap for SmartConsole Utility
Optional SFP Transceivers
DGS-1500-28P will be released in late 2011.
5 Will be available in a future release in 2012. IPv6 Ready Logo Phase II will be obtained in the future.
6
Available for DGS-1500-28P only.
• Backup/Upgrade firmware
• Smart Wizard
- Max. 500 log entries
• BootP/DHCP Client
• SNTP
• ICMP v65
• IPv4/v6 Dual Stack5
• DHCP Auto Configuration
• Debug Command
• Time Setting
- SNTP
• RMON1
• Trusted Host
• Time-based PoE6
• User Account
• Upload/Download Configuration file
Green
• Power Saving by:
- Link Status
- Cable Length
- LED Shutoff
- Port Standby
- System Hibernation
Security Features
• Access Control List secures network
• D-Link Safeguard Engine protects CPU from
Broadcast/Multicast/Unicast Flooding
• Port Security supports 64 MACs per port
• ARP Spoofing Prevention
• SSL
Certification
• IPv6 Core Ready Logo Phase II5
Intuitive Management
Optional WDM SFP Transceivers
Supported by DGS-1500-20/28/28P4
Supported by DGS-1500-20/28/28P4/52
DGS-712
1000BASE-T Copper
DEM-330T/R
DV-600S
DEM-310GT
1000BASE-LX, Single-mode, 10 km
D-View 6.0 Network Management
System (Standard Edition)
DV-600P
D-View 6.0 Network Management
System (Professional Edition)
1000BASE-SX, Multi-mode, 550 m
DEM-312GT2 1000BASE-SX, Multi-mode, 2 km
DEM-314GT
1000BASE-LHX, Single-mode, 50 km
DEM-315GT
1000BASE-ZX, Single -mode, 80km
Supported by DGS-1500-52
DGS-712
1000BASE-T Copper
DEM-310GT
1000BASE-LX, Single-mode, 10 km
DEM-311GT
1000BASE-SX, Multi-mode, 550 m
DEM-331T/R
1000BASE-LHX, Single-mode, 50km
DEM-315GT
1000BASE-ZX, Single-mode, 80km
DEM-210
100BASE-BX, Single-mode, 15 km
DEM-211
100BASE-BX, Multi-mode, 2 km
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 40 km
VoIP Deployment
• Highest priority for VoIP services
• Auto Voice VLAN
QoS (Quality of Service)
Optional Redundant Power Supply
Supported by DGS-1500-28P
DEM-330T/R
DPS-700
DEM-312GT2 1000BASE-SX, Multi-mode, 2 km
DEM-314GT
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 10 km
Supported by DGS-1500-52
DEM-331T/R
• SmartConsole utility or Web-based GUI
• Single IP Management (Virtual Stacking)
• Built-in SNMP MIB for remote NMS
(D-View 6.0)
Optional Management Software
Supported by DGS-1500-20/28/28P4
DEM-311GT
4
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 10 km
589 Watts Redundant Power Supply
370 Watts PoE Power Budget
• Supports IEEE 802.1p QoS,
up to four Priority Queues per port
• Bandwidth Control
• DSCP
Advanced Features
• Layer 3 Static Routing
• IPv6 support2
• Auto Surveillance VLAN
• Loopback Detection automatically disables
a port or VLAN when a loop is detected
• Cable Diagnostics allows administrators
to determine cable status
• Configurable MDI/MDIX
• LLDP/LLDP-MED
Gigabit
Wavelength Tx:1550 nm, Rx:1310 nm
Single-mode, 40 km
Trap & Logs
• SNMP Trap
• Trap for SmartConsole Utility
Online Help
• Link to local support website
• Online User Guide
For further information: www.dlink.eu
4
DGS-1500-28P will be released in late 2011.
Will be available in a future release in 2012. IPv6 Ready Logo Phase II will be obtained in the future.
Available for DGS-1500-28P only.
5 4
• System Log
• IEEE 802.3az EEE
• Power saving via LED and Port shutoff
• Power saving via Port Standby
• Power saving via System Hibernation
• Power saving via Cable Length detection
• Power saving via Link Status detection
• Time-based PoE (DGS-1500-28P1 only)
Optional Products
RFC Standard Compliance
• RFC 783 TFTP
• RFC 854 Telnet Server
• RFC 951 BootP/DHCP Client
• RFC 1157 SNMP v1, v2, v3
• RFC 1213 MIB II
• RFC 1215 MIB Traps Convention
• RFC 1350 TFTP
• RFC 1493 Bridge MIB
• RFC 1769 SNTP
• RFC 1542 BootP/DHCP Client
• RFC 1901 SNMP v1, v2, v3
• RFC 1907 SNMP v2 MIB
• RFC 1908 SNMP v1, v2, v3
• RFC 2068 FCS
• RFC 2131 BootP/DHCP Client
• RFC 2138 RADIUS Authentication
• RFC 2139 RADIUS Authentication
• RFC 2233 Interface Group MIB
• RFC-2246 SSL
• RFC 2475
• RFC 2570 SNMP v1, v2, v3
• RFC 2575 SNMP v1, v2, v3
• RFC 2598 CoS
• RFC 2616 FCS
• RFC 2618 RADIUS Authentication
• RFC 2819 RMON v1
• RFC 2865 RADIUS Authentication
• RFC 3164 System Log
• RFC 3195 System Log
• RFC 3411-17 SNMP
• RFC 3621 Power Ethernet MIB
Green Technology
6
C
US
ACN 052 202 838
I
D-Link European Headquarters. D-Link (Europe) Ltd., D-Link House, Abbey Road, Park Royal, London, NW10 7BX. Specifications are subject to change without notice. D-Link is a registered
trademark of D-Link Corporation and its overseas subsidiaries. All other trademarks belong to their respective owners. ©2011 D-Link Corporation. All rights reserved. Europe Release September 2011
D-Link’s DGS-1500 Series SmartPro switches
are designed for businesses which require
functions such as L3 Static Routing and Single
IP Management (Virtual Stacking) without
upgrading to a managed switch. This series
integrates advanced management and
security functions that are similar to those
of a managed switch, but less complex.
The switches feature D-Link GreenTM 3.0
technology which enables significant power
savings. Additionally, the DGS-1500-28P1’s
10/100/1000 Mbps ports are PoE-enabled,
offering ease-of-use and green features like
Time-based PoE, which enables the power
to the port to be shut off at a predetermined
time. Compliant with 802.3af and 802.3at,
these switches are capable of feeding power
to devices of up to 30 Watts. Management
options include SNMP, Web Management,
SmartConsole Utility, and Compact CLI. The
series also supports ACL filtering and D-Link’s
Safeguard Engine to protect the network.
The DGS-1500-20 and DGS-1500-28 both
feature a fanless design. The fanless design
allows them to emit less heat and noise than
a standard switch, making them suitable for
office environments. The DGS-1500-28P1 and
DGS-1500-52 both feature smart fans. Using
a thermal sensor that can detect temperature
change, the smart fans can react accordingly
by utilising different fan speeds for different
temperatures.
Advanced Features
The DGS-1500 Series integrates advanced
features such as Virtual Stacking and Layer 3
features like Static Routing. Virtual Stacking
reduces the number of IP addresses needed
on a network by configuring up to 32 devices
to appear as a single unit with one IP address.
This simplifies network management for small
workgroups and allows for switches to be
added without special cabling.
1
2
Extensive Layer 2 Features
These switches are equipped with a complete
lineup of Layer 2 features including IGMP
Snooping, Port Mirroring, Spanning Tree, and
Link Layer Discovery Protocol (LLDP). The IEEE
802.3x Flow Control function allows servers to
directly connect to the switch for fast, reliable
data transfer. At 2000 Mbps Full Duplex,
the Gigabit ports provide high-speed data
pipes to servers with minimum data transfer
loss. Network maintenance features include
Loopback Detection and Cable Diagnostics.
Loopback Detection is used to detect loops
created by a specific port or VLAN and
automatically shut down the affected port or
VLAN. The Cable Diagnostics feature, designed
primarily for adminstrators and customer
service representatives, can quickly discover
the type of error on cables and determine the
cable quality.
QoS, Bandwidth Control
The DGS-1500 Series supports Auto
Surveillance VLAN (ASV) and Auto Voice VLAN,
which are best suited for VoIP and video
surveillance deployments. Auto Surveillance
VLAN is a new, industry-leading technology
built into D-Link Smart Switches. This
technology consolidates data and surveillance
video transmission through a single SmartPro
switch, thus sparing businesses the expense
of maintaining dedicated hardware and
facilities. ASV also ensures the quality of
real-time video for monitoring and control
without compromising the transmission of
conventional network data. The Auto Voice
VLAN technology enhances VoIP service by
automatically placing voice traffic from an
IP phone to an assigned VLAN. With higher
priority and an individual VLAN, these features
guarantee the quality and security of VoIP
traffic. Furthermore, the DSCP markings on
Ethernet packets enable different levels of
service to be assigned to network traffic.
DGS-1500-28P will be released in late 2011.
IPv6 Ready Logo Phase II will be obtained in the future. IPv6 support will be available in a future release.
Download PDF

advertising