Spill Proof Water Dispenser

Spill Proof Water Dispenser
IMPORTANT: Do Not Return Dispenser to Store. If you have questions or issues please contact 1-866-429-7566 for expert assistance.
FEATURES & FUNCTIONS
Water Bottle – Not included. Uses 11.3 to 18.9 litre bottles.
Spill Proof Bottle Receptacle with Leak Guard – For fast, easy, spillproof loading. Reduces leaks from worn & damaged bottles.
Spill Proof
Water Dispenser
Cold Water Control – Depress paddle to dispense. Release paddle to
stop.
Hot Water Control with Child Safety Feature – Press and hold red
button then depress paddle to dispense. Release paddle to stop.
Model # 601159
SAFETY PRECAUTIONS
To reduce risk of injury and property damage, user must read this
entire guide before assembling, installing & operating dispenser.
Failure to execute the instructions in this manual can cause
personal injury or property damage.
This product dispenses water at very high temperatures. Failure to
use properly can cause personal injury.
When operating this dispenser, always exercise basic safety
precautions, including the following:


LED Nightlight – Helps in low light situations.
Spouts –
Cold water comes out here.
Hot water comes out here.
TO REDUCE THE RISK OF INJURY
AND PROPERTY DAMAGE, USER
MUST READ THIS MANUAL
BEFORE ASSEMBLING, INSTALLING
& OPERATING DISPENSER.
Drip Tray & Grid with Full Indicator – Dishwasher safe. Snaps in and
out. Red full indicator in tray rises when full of water. To dispense
water, place glass or cup over left or right hole.






SAVE THIS MANUAL
FOR FUTURE USE
Energy Saver Switches – Located on back. Switch red control to off to
stop heating. Switch green control to off to stop cooling.

Nightlight Switch – Located on back. Allows you to choose to have
the nightlight ON or OFF.







LOCATING DISPENSER
Prior to use, this dispenser must be properly assembled and installed in
accordance with this manual.
This dispenser is intended for water dispensing only. Do NOT use other liquids.
Do NOT use for other purposes. Never use any other liquid in the dispenser
other than known and microbiologically safe bottled water.
For indoor use only. Keep water dispenser in a dry place away from direct
sunlight. Do NOT use outdoors.
Install and use only on a hard, flat and level surface.
Do NOT place dispenser into an enclosed space or cabinet.
Do NOT operate dispenser in the presence of explosive fumes.
Position back of dispenser no closer than 4 inches from wall and permit free
airflow between wall and dispenser. There must be at least 4 inches clearance
on the sides of the dispenser to permit airflow.
Use only properly grounded outlets.
Do not use an extension cord with your water dispenser.
Always grasp plug and pull straight out from outlet. Never unplug by pulling on
power cord.
Do NOT use dispenser if cord becomes frayed or otherwise damaged.
To protect against electric shock, do NOT immerse cord, plug, or any other part
of dispenser in water or other liquids.
Ensure dispenser is unplugged prior to cleaning.
Never allow children to dispense hot water without proper and direct
supervision. Unplug unit to prevent unsupervised use by children.
Do not dispense hot water if water bottle is empty.
Service should be performed only by a certified technician. Please contact us at
866-429-7566 for assistance.
This unit has been tested and sanitized prior to packing and shipping. During
transit dust and odors can accumulate in the tank and lines. Dispense and
dispose at least one quart of water prior to drinking any water.
Water is leaking.
1. Remove tamper seal from top of bottle cap. Do NOT remove plastic cap.
After setup, it will take 1 hour to get water to maximum cold temperature.
During this time the compressor will run continuously. This is normal.
2. Clean bottle cap and neck with a cloth and warm soapy water, then rinse.
1. Position bottle, glass, pitcher or cooking pot below spout.
3. Lift bottle and insert onto the probe. Apply slight pressure until the plug
inside the cap pushes in and the bottle is seated. Water will begin to flow
into the reservoirs causing air bubbles in the bottle.
2. Using your beverage container, depress cold water paddle towards
dispenser to start cold water flow.
-
-
Install plastic anchor directly
into sheet rock using a Philips
screwdriver. DO NOT drill hole
into sheet rock first when using
this anchor.
Secure by installing screw
through bracket and into the
anchor.
3. Release cold water paddle once desired fill level is achieved.
Provide Electricity
Plug cord into a ground fault interrupting receptacle.
Dispensing Hot Water (85°C – 92°C)
Activate Heating & Cooling
Notice: This unit will not dispense hot or cold water until the switches are
activated.
If you do not want to heat water, push bottom side of red switch to OFF.
-
If you do not want to cool water, push bottom side of green switch to OFF.
Note
Activate Nightlight
Remove screw to free dispenser for
cleaning or relocating.
To activate, push top side of the blue switch (ON) in.
Bottle may have a leak that is too large for the Leak Guard feature to stop.
Remove bottle, dispense one quart of water and install new bottle.

If leak remains, remove bottle and call 866-429-7566 for assistance.
No water is coming from the spout.

Make sure the bottle is not empty. If empty, replace it.

Make sure to push the water controls in fully.
Cold water is not cold.

It takes up to one hour after setup to dispense cold water.

Make sure the power cord is properly connected to a working outlet.

Make sure the back of the dispenser is at least 10 cm from a wall and there
is free airflow on all 4 sides of the dispenser.

Make sure green power switch on back of dispenser is ON.

If water still isn’t cold, please call 866-429-7566 for assistance.
Hot water is not hot.
To activate, push top side of the switches (ON) in to start heating or cooling the
water.
-

Dispensing Cold Water (3°C – 10°C)
2. Locate dispenser on a hard and level surface in a cool shaded
location near a ground fault interrupting receptacle.
Clip bracket onto back right
corner of dispenser as shown in
illustration.
Primo Water Corporation
101 N Cherry St., Suite 501
Winston-Salem, NC 27101
866-429-7566
www.PrimoWater.com
Assemble
Install Water Bottle
-
The Limited Warranty is in lieu of all other express warranties. Vendor disclaims all
warranties for products that are purchased from seller other than authorized
retailers or distributors. AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS
WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. FURTHER, VENDOR SHALL HAVE NO LIABILITY
WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT,
PUNITIVE, INCIDENTAL, OR CONSEQUENTAL DAMAGES. Vendor assumes no
responsibility for any defects caused by third parties. This Limited Warranty gives
the purchaser specific legal rights; a purchaser may have other rights depending
upon where he or she lives. Some jurisdictions do not allow exclusion or limitation
of special, incidental or consequential damages, or limitations on how long a
warranty lasts, so the above exclusion and limitations may not apply to you.
TROUBLESHOOTING
1. Place dispenser upright.
4. Install bracket to prevent accidental
tip over:
The Limited Warranty does not cover any failures or operating difficulties due to
accident, abuse, misuse, alteration, misapplication, improper installation or
improper maintenance or service by you or any third party, or failure to perform
normal and routine maintenance on the dispenser, as set out in the User’s Manual.
In addition, the Limited Warranty does not cover damages to the finish, such as
scratches, dents, discoloration or rust after purchase.
DISPENSING WATER
2. Snap drip tray and grid assembly in place.
3. Position dispenser so the back is at least 10 cm from wall and there
are at least 10 cm of clearance on both sides.
Primo Water Corporation, (“Vendor”) warrants to the original purchaser of this
dispenser, and to no other person, that if this dispenser is assembled and operated
in accordance with the printed instructions accompanying it, then for a period of
one (1) year from the date of purchase, all parts in such dispenser shall be free from
defects in material and workmanship. Vendor may require reasonable proof of your
date of purchase from an authorized retailer or distributor. Therefore, you should
retain your sales slip or invoice. The Limited Warranty shall be limited to repair or
replacement of parts, which prove defective under normal use and service and
which Vendor shall determine in its reasonable discretion upon examination to be
defective. Before returning any parts, you should contact Vendor’s Customer
Service Department using the contact information listed below. If Vendor confirms,
after examination, a defect covered by this Limited Warranty in any returned part,
and if Vendor approves claim, Vendor will replace such defective part without
charge. If you return defective parts, transportation charges must be prepaid by
you. Vendor will return replacement parts to original purchaser, freight or postage
prepaid.
GETTING STARTED
1. Remove drip tray and grid assembly from protective packaging.
Notice: Do NOT plug in power cord yet.
LIMITED WARRANTY
After setup, hot water will be available in 15-20 minutes.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Press red button and depress paddle with beverage container to start hot
water flow.
3. Release hot water paddle once desired fill level is achieved.

It takes 15-20 minutes after setup to dispense hot water.

Make sure the power cord is properly connected to a working outlet.

Make sure red power switch on back of dispenser is ON.
Nightlight Isn’t Working

Make sure the power cord is properly connected to a working outlet.

Make sure nightlight power switch on back of dispenser is ON.
Register Online
While you wait for your dispenser to get the water hot and cold, please register
your dispenser. This will be helpful should you need customer service
assistance in the future.
Dispenser Is Noisy

Make sure the dispenser is positioned on a level surface.
Go to www.PrimoWater.com and click on Customer Care.
© 2014 Primo Water Corporation
Please visit www.PrimoWater.com for more useful information, instructional videos, tips and special offers.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising